BTS700201ESPXUMA2 - 23.2A Smart High-Side Switch | Infineon
部品番号: BTS700201ESPXUMA2 ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $3.85 | $3.85 |
| 10 | $3.47 | $34.70 |
| 100 | $3.05 | $305.00 |
| 500 | $2.74 | $1,370.00 |
| 1,000 | $2.46 | $2,460.00 |
| 3,000 | $2.18 | $6,540.00 |
BTS700201ESPXUMA2 概要
A smart high-side switch is a type of power distribution IC that sits between a battery or DC bus and a resistive or inductive load, replacing mechanical relays and discrete MOSFETs with a self-protected solid-state solution. Within the broader power management hierarchy, this part sits as: high-side switch -> power distribution switch -> PMIC (Power Management IC) -> semiconductor. PROFET+2 12V devices specifically target 12 V automotive battery rails where load-dump transients, jump-start conditions, and cranking pulses are routine.
Key features include a 2.3 mOhm typical on-state resistance, integrated reverse battery protection, configurable current limiting, over-temperature shutdown, ground-loss detection, and diagnostic feedback via an IS pin. The 1:1 input-to-output topology makes it functionally equivalent to a low-side controlled mechanical relay. An internal charge pump generates the VGS needed to fully enhance the N-channel output MOSFET from a 12 V supply rail.
The device operates across -40C to +150C junction temperature, satisfying AEC-Q100 automotive qualification requirements. The PG-TSDSO-24-32 exposed-pad package offers a thermal resistance optimized for sustained high-current operation with PCB copper heat spreading. Per Infineon datasheet, the part is intended for automotive and industrial applications including lighting, body controllers, and motor drive.
Typical applications include automotive front and rear lighting, body control modules driving seat heaters and window lifts, HVAC blower motors, and industrial 24 V/12 V solenoid or relay-replacement circuits. The diagnostic IS output supports fault reporting to a microcontroller for OBC (on-board charger) and BCM (body control module) systems.
Designers should size the PCB copper area under the exposed pad to keep junction temperature below 150C at worst-case ambient and load current. The IS pin current is proportional to load current and must be connected to a microcontroller ADC or comparator with appropriate filtering to avoid false trip events during inrush.
This page consolidates distributor pricing, drop-in alternatives within the PROFET+2 12V family, and practical design notes not covered in the standalone Infineon datasheet PDF.
ドロップイン代替品: BTS700201ESPXUMA2 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: BTS700201ESPXUMA2 （同一形状・フットプリント） — 相違点: Package, Diagnostic Output, Operating Temperature Range, Product Family, Protection Features.
クイック比較ツール — 並列比較する代替部品を選択:
BTS70020-1ESP
✅ ドロップイン📋 参考代替品（カタログ未掲載）
BTS70020-1EPAXUMA1
✅ ドロップイン📋 参考代替品（カタログ未掲載）
BTS700201EPAXUMA1
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
BTS700202EPAXUMA1
✅ ドロップイン📋 参考代替品（カタログ未掲載）
BTS700102EPAXUMA1
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
BTS700201ESPXUMA2 最大定格＆電気的特性
| Manufacturer | Infineon Technologies |
| Product Family | PROFET+2 12V |
| 機能 | Smart High-Side Power Switch |
| トポロジー | 1:1 N-Channel High-Side |
| Maximum Continuous Load Current | 23.2 A |
| Typical RDS(ON) | 8.5 mOhm |
| Datasheet RDS(ON) | 2.3 mOhm |
| Maximum Load Voltage | 70 V |
| Operating Voltage Range | 4 V to 28 V (12 V nominal) |
| パッケージ | PG-TSDSO-24-32 |
| ピン数 | 24 |
| 実装タイプ | Surface Mount |
| 動作温度範囲 | -40C to +150C (TJ) |
| Automotive Qualification | AEC-Q100 qualified |
| RoHS ステータス | Compliant |
| Diagnostic Output | IS pin (current sense) |
| Protection Features | Reverse battery, over-current, over-temperature, ground loss |
BTS700201ESPXUMA2 ピン構成
| ピン 1 | VBB — Battery supply (12 V nominal) |
| ピン 2 | VBB — Battery supply |
| ピン 3 | OUT — Switched output to load |
| ピン 4 | OUT — Switched output |
| ピン 5 | GND — Ground reference |
| ピン 6 | GND — Ground |
| ピン 7 | IN — Logic-level input control |
| ピン 8 | IS — Current sense / diagnostic output |
| ピン 9 | NC — Not connected |
| ピン 10 | NC — Not connected |
| ピン 11 | NC — Not connected |
| ピン 12 | NC — Not connected |
| ピン 13 | NC — Not connected |
| ピン 14 | NC — Not connected |
| ピン 15 | NC — Not connected |
| ピン 16 | NC — Not connected |
| ピン 17 | NC — Not connected |
| ピン 18 | NC — Not connected |
| ピン 19 | NC — Not connected |
| ピン 20 | NC — Not connected |
| ピン 21 | NC — Not connected |
| ピン 22 | NC — Not connected |
| ピン 23 | NC — Not connected |
| ピン 24 | EP — Exposed thermal pad - connect to VBB or large copper |
主な用途
BTS700201ESPXUMA2 の用途: 6 件s: Automotive Front and Rear Lighting, Body Control Module (BCM) Loads, HVAC Blower and Fan Motors, Industrial 24 V Solenoid and Relay Replacement, Power Distribution and Fuse Replacement, Auxiliary Heater and PTC Heating.
Automotive Front and Rear Lighting
The BTS700201ESPXUMA2 drives LED headlamp modules, tail lamps, and turn signals from a 12 V battery rail with 23.2 A continuous capability. Its 2.3 mOhm typical RDS(ON) minimizes conduction loss so multi-LED strings reach full brightness without thermal stress on the switch. The IS pin provides diagnostic current-sense feedback to the BCM for open-load and short-circuit detection, while integrated reverse-battery and load-dump protection (70 V transient) withstands harsh automotive electrical transients. This makes it well suited to replace electromechanical lighting relays.
おすすめ
Body Control Module (BCM) Loads
Within a body control module, the BTS700201ESPXUMA2 powers seat heaters, window lifts, door locks, and mirror adjusters directly from the 12 V bus. Its 23.2 A rating handles inrush from DC motors while the embedded current limit and over-temperature shutdown protect against stall conditions. Per Infineon application notes, the device operates across -40C to +150C, matching under-hood and cabin ambient profiles. The 1:1 input-to-output digital control interface allows direct GPIO drive from the BCM microcontroller.
おすすめ
HVAC Blower and Fan Motors
The BTS700201ESPXUMA2 is well matched to 12 V HVAC blower motors and cooling fans where steady-state current can approach 20 A. Its low 2.3 mOhm RDS(ON) reduces heat dissipation at full load, while the exposed-pad PG-TSDSO-24-32 package spreads heat into PCB copper. Integrated PWM capability (driven from the IN pin) allows variable fan-speed control without external MOSFETs. The IS pin current sense provides stall and blockage detection for safety diagnostics.
おすすめ
Industrial 24 V Solenoid and Relay Replacement
In industrial automation, the BTS700201ESPXUMA2 replaces electromechanical relays driving 24 V solenoids, valves, and indicator loads. The 70 V transient rating tolerates inductive kick from de-energized coils, and the diagnostic IS pin reports wiring faults to a PLC. AEC-Q100 qualification extends lifetime in factory environments with thermal cycling. Its solid-state design eliminates contact bounce and arcing, improving reliability over mechanical switching.
おすすめ
Power Distribution and Fuse Replacement
The BTS700201ESPXUMA2 acts as a resettable electronic fuse in 12 V distribution boxes, replacing blade fuses with software-controlled switching. Per Infineon datasheet, the integrated current limit and over-temperature shutdown self-protect downstream wiring during overload conditions, eliminating the need to replace blown fuses. The IS pin allows fault logging in the body control module for predictive maintenance. Multiple BTS700201ESPXUMA2 channels can be paralleled in software for higher-current rails.
おすすめ
Auxiliary Heater and PTC Heating
PTC cabin heaters and auxiliary heating elements draw sustained high current from 12 V rails, making the BTS700201ESPXUMA2 a suitable solid-state driver. With 23.2 A continuous rating and 2.3 mOhm RDS(ON), it minimizes dissipation in confined under-dash installations. The exposed thermal pad of the PG-TSDSO-24-32 package supports PCB copper heat spreading. The device's diagnostic IS pin enables overtemperature and fault reporting to the climate control module.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: BTS700201ESPXUMA2 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | BTS70020-1ESP | BTS70020-1EPAXUMA1 | BTS700201EPAXUMA1 | BTS700202EPAXUMA1 | BTS700102EPAXUMA1 |
|---|---|---|---|---|---|---|
| Brand | Infineon | Infineon | Infineon | Infineon | Infineon | Infineon |
| Package | PG-TSDSO-24-32 | PG-TSDSO-24-32 - same | PG-TSDSO-24-32 - same | PG-TSDSO-24-32 - same | PG-TSDSO-24-32 - same | PG-TSDSO-24-32 - same |
| Maximum Continuous Load Current | 23.2 A | 23.2 A | 23.2 A | 23.2 A | 11.6 A (per channel, dual) | 11.6 A |
| Typical RDS(ON) | 2.3 mOhm | 2.3 mOhm | 2.3 mOhm | 2.3 mOhm | 4.6 mOhm | 10 mOhm |
| Maximum Load Voltage | 70 V | 70 V | 70 V | 70 V | 70 V | 70 V |
| Channels | 1 | 1 | 1 | 1 | 2 | 1 |
| Automotive Qualification | AEC-Q100 | AEC-Q100 | AEC-Q100 | AEC-Q100 | AEC-Q100 | AEC-Q100 |
| Operating Temperature Range | -40C to +150C (TJ) | -40C to +150C | -40C to +150C | -40C to +150C | -40C to +150C | -40C to +150C |
主な差別化要因
- 23.2 A continuous current in a single PG-TSDSO-24-32 channel （vs BTS428L2ATMA1)
- Single-channel high current vs dual-channel lower current （vs BTS700202EPAXUMA1)
- Lower RDS(ON) than other family members （vs BTS700102EPAXUMA1)
設計ノート
Estimated: at 23.2 A load current with 2.3 mOhm typical RDS(ON), the conduction loss is approximately 1.23 W. Combined with switching losses in PWM applications, the PG-TSDSO-24-32 exposed pad should be soldered to at least 6 square centimeters of copper to keep the junction-to-ambient thermal resistance within acceptable limits. For continuous high-current operation above 15 A, additional copper on inner PCB layers connected via thermal vias is recommended.
Do not connect the IS pin directly to 5 V or 3.3 V logic - it is a current source output requiring a pull-down resistor to ground (typically 1 kOhm). The IS pin voltage must be limited to the ADC reference of the monitoring microcontroller to avoid damage. Per Infineon datasheet, IS pin leakage in OFF state can cause false open-load detection if the wiring harness has significant capacitance; add a small RC filter if fault flags are spurious.
Keep high-current traces (VBB and OUT) wide and short to minimize parasitic inductance that can produce voltage transients during turn-off. Place a 100 nF ceramic decoupling capacitor close to the VBB pin to absorb fast transients. The exposed pad (EP) must be soldered for both thermal performance and mechanical reliability; thermal vias to internal copper planes significantly improve heat spreading.
Although the BTS700201ESPXUMA2 integrates reverse-battery protection, an external TVS diode (such as SMBJ series) on the VBB line is recommended for severe load-dump transients beyond ISO 7637-2 pulse B requirements. The internal protection handles 70 V transients, but sustained overvoltage conditions may still activate the over-temperature shutdown. Verify TVS clamping voltage is below the 70 V maximum load voltage rating.
コンプライアンス情報
AEC-Q100 qualified per Infineon product page. RoHS and REACH compliant. PROFET+2 12V family is lead-free and halogen-free per Infineon datasheet.
