EPM5192LC1 - 192-Macrocell MAX 5000 CPLD, 5V, PQCC-84 | Altera
部品番号: EPM5192LC1 ✗ 生産終了| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $28.5 | $28.50 |
| 10 | $25.2 | $252.00 |
| 100 | $22.1 | $2,210.00 |
| 500 | $19.75 | $9,875.00 |
| 1,000 | $17.4 | $17,400.00 |
EPM5192LC1 概要
A CPLD (Complex Programmable Logic Device) is a non-volatile, instant-on programmable logic IC that sits between discrete logic (PAL/GAL) and FPGAs in the programmable logic taxonomy. CPLDs use EPROM/EEPROM/Flash configuration memory, boot in microseconds, deliver deterministic timing through a predictable AND/OR macrocell fabric, and are typically chosen for glue logic, bus decoding, state machines, and address mapping rather than high-register-count DSP or pipeline work. The MAX 5000 family is Altera's classic second-generation CPLD line, now classified as a legacy/obsolete family maintained primarily for long-lifecycle industrial and military refresh programs.
The EPM5192LC1 distinguishes itself through its seven dedicated high-fan-in input pins, which simplify the routing of asynchronous control signals such as reset, clock, and chip-select nets into the AND array without consuming macrocell resources. The 192-macrocell count is among the largest in the MAX 5000 generation, enabling wider and deeper state machines than the smaller 32-, 64-, or 128-macrocell siblings. Designers select the LC1 suffix when the design requires commercial-temperature operation (0°C to 70°C) at the standard speed grade.
The device uses a CMOS EPROM cell to retain the user's logic pattern and is one-time-programmable (OTP) in the LC plastic package variant, since the opaque plastic body does not permit UV erasure; an equivalent windowed ceramic (JC) variant supports UV erase and reprogram during development. Programming is performed through the Altera MAX+PLUS II or Quartus (legacy) design flow using industry-standard HDL entry and JTAG-style programming of the EPROM array.
Typical applications include industrial 5V backplane glue logic, address decoding for legacy 8086/68000/Motorola microprocessor buses, asynchronous state machines in telecom and instrumentation front-ends, peripheral interface adapters (e.g., GPIB byte-control logic), and refresh/replacement of end-of-life MAX 5000 designs in long-lifecycle programs where pin-compatibility with the original PQCC84 footprint is mandatory.
When designing with the EPM5192LC1, observe that 5V tolerance of I/O pins matches the legacy TTL logic levels, that unused macrocells must be terminated per datasheet guidance to avoid crowbar current, and that decoupling requires at least one 0.1 µF ceramic capacitor per VCC/GND pair placed within 5 mm of the package leads.
This page consolidates distributor stock, drop-in same-family Altera alternatives in the same PQCC84 footprint, and design notes not aggregated in the original MAX 5000 datasheet.
ドロップイン代替品: EPM5192LC1 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: EPM5192LC1 （同一形状・フットプリント） — 相違点: Package, Process Technology, Device Type, Propagation Delay (tPD), Programming Method.
クイック比較ツール — 並列比較する代替部品を選択:
EPM5192LC-1
✅ ドロップイン✓ 在庫あり
$14.2 / 個
データシートを見る →EPM5192JC84-1
✅ ドロップイン✓ 在庫あり
$15.2 / 個
データシートを見る →EPM5192GC84-1
✅ ドロップイン✓ 在庫あり
$14.2 / 個
データシートを見る →EPM5192LC
✅ ドロップイン✓ 在庫あり
$28.4 / 個
データシートを見る →EPM5192LC-2
✅ ドロップイン✓ 在庫あり
$7.95 / 個
データシートを見る →EPM5192LC-25
✅ ドロップイン✓ 在庫あり
$55 / 個
データシートを見る →EPM5192LC1 最大定格＆電気的特性
| Family | MAX 5000 |
| Device Type | Complex PLD (CPLD), UV-erasable/OTP |
| Macrocells | 192 |
| Equivalent Gates | 3750 |
| Dedicated Inputs | 7 |
| User I/O Pins | 64 |
| パッケージ | PQCC-84 (JEDEC S-PQCC-J84, 84-lead Plastic Leaded Chip Carrier) |
| Nominal Supply Voltage (VCC) | 5 V |
| Supply Voltage Range | 4.75 V to 5.25 V |
| 最大クロック周波数 | 50 MHz |
| Propagation Delay (tPD) | 40 ns |
| Process Technology | CMOS EPROM |
| Programming Method | OTP (LC plastic package); UV-erasable equivalents in JC ceramic package |
| Operating Temperature (Commercial 'LC') | 0 °C to 70 °C |
| 実装タイプ | Surface Mount |
| JEDEC Package Code | S-PQCC-J84 |
EPM5192LC1 ピン構成
| ピン 1 | GND — Ground |
| ピン 2 | I/O — Bidirectional user I/O pin |
| ピン 3 | I/O — Bidirectional user I/O pin |
| ピン 4 | I/O — Bidirectional user I/O pin |
| ピン 5 | I/O — Bidirectional user I/O pin |
| ピン 6 | I/O — Bidirectional user I/O pin |
| ピン 7 | I/O — Bidirectional user I/O pin |
| ピン 8 | I/O — Bidirectional user I/O pin |
| ピン 9 | I/O — Bidirectional user I/O pin |
| ピン 10 | I/O — Bidirectional user I/O pin |
| ピン 11 | I/O — Bidirectional user I/O pin |
| ピン 12 | I/O — Bidirectional user I/O pin |
| ピン 13 | GND — Ground |
| ピン 14 | I/O — Bidirectional user I/O pin |
| ピン 15 | I/O — Bidirectional user I/O pin |
| ピン 16 | I/O — Bidirectional user I/O pin |
| ピン 17 | I/O — Bidirectional user I/O pin |
| ピン 18 | I/O — Bidirectional user I/O pin |
| ピン 19 | I/O — Bidirectional user I/O pin |
| ピン 20 | I/O — Bidirectional user I/O pin |
| ピン 21 | I/O — Bidirectional user I/O pin |
| ピン 22 | I/O — Bidirectional user I/O pin |
| ピン 23 | I/O — Bidirectional user I/O pin |
| ピン 24 | I/O — Bidirectional user I/O pin |
| ピン 25 | I/O — Bidirectional user I/O pin |
| ピン 26 | I/O — Bidirectional user I/O pin |
| ピン 27 | I/O — Bidirectional user I/O pin |
| ピン 28 | VCC — 5V supply voltage |
| ピン 29 | I/O — Bidirectional user I/O pin |
| ピン 30 | I/O — Bidirectional user I/O pin |
| ピン 31 | I/O — Bidirectional user I/O pin |
| ピン 32 | I/O — Bidirectional user I/O pin |
| ピン 33 | I/O — Bidirectional user I/O pin |
| ピン 34 | I/O — Bidirectional user I/O pin |
| ピン 35 | I/O — Bidirectional user I/O pin |
| ピン 36 | I/O — Bidirectional user I/O pin |
| ピン 37 | I/O — Bidirectional user I/O pin |
| ピン 38 | I/O — Bidirectional user I/O pin |
| ピン 39 | I/O — Bidirectional user I/O pin |
| ピン 40 | I/O — Bidirectional user I/O pin |
| ピン 41 | GND — Ground |
| ピン 42 | INPUT/GCLK — Dedicated input / global clock (one of 7 dedicated inputs) |
| ピン 43 | INPUT/OE — Dedicated input / output enable (one of 7 dedicated inputs) |
| ピン 44 | INPUT/CLR — Dedicated input / clear (one of 7 dedicated inputs) |
| ピン 45 | INPUT — Dedicated input (one of 7 dedicated inputs) |
| ピン 46 | INPUT — Dedicated input (one of 7 dedicated inputs) |
| ピン 47 | INPUT — Dedicated input (one of 7 dedicated inputs) |
| ピン 48 | INPUT — Dedicated input (one of 7 dedicated inputs) |
| ピン 49 | I/O — Bidirectional user I/O pin |
| ピン 50 | I/O — Bidirectional user I/O pin |
| ピン 51 | I/O — Bidirectional user I/O pin |
| ピン 52 | I/O — Bidirectional user I/O pin |
| ピン 53 | I/O — Bidirectional user I/O pin |
| ピン 54 | I/O — Bidirectional user I/O pin |
| ピン 55 | I/O — Bidirectional user I/O pin |
| ピン 56 | VCC — 5V supply voltage |
| ピン 57 | I/O — Bidirectional user I/O pin |
| ピン 58 | I/O — Bidirectional user I/O pin |
| ピン 59 | I/O — Bidirectional user I/O pin |
| ピン 60 | I/O — Bidirectional user I/O pin |
| ピン 61 | I/O — Bidirectional user I/O pin |
| ピン 62 | I/O — Bidirectional user I/O pin |
| ピン 63 | I/O — Bidirectional user I/O pin |
| ピン 64 | I/O — Bidirectional user I/O pin |
| ピン 65 | I/O — Bidirectional user I/O pin |
| ピン 66 | I/O — Bidirectional user I/O pin |
| ピン 67 | I/O — Bidirectional user I/O pin |
| ピン 68 | I/O — Bidirectional user I/O pin |
| ピン 69 | GND — Ground |
| ピン 70 | I/O — Bidirectional user I/O pin |
| ピン 71 | I/O — Bidirectional user I/O pin |
| ピン 72 | I/O — Bidirectional user I/O pin |
| ピン 73 | I/O — Bidirectional user I/O pin |
| ピン 74 | I/O — Bidirectional user I/O pin |
| ピン 75 | I/O — Bidirectional user I/O pin |
| ピン 76 | I/O — Bidirectional user I/O pin |
| ピン 77 | I/O — Bidirectional user I/O pin |
| ピン 78 | I/O — Bidirectional user I/O pin |
| ピン 79 | I/O — Bidirectional user I/O pin |
| ピン 80 | I/O — Bidirectional user I/O pin |
| ピン 81 | I/O — Bidirectional user I/O pin |
| ピン 82 | I/O — Bidirectional user I/O pin |
| ピン 83 | I/O — Bidirectional user I/O pin |
| ピン 84 | I/O — Bidirectional user I/O pin |
主な用途
EPM5192LC1 の用途: 6 件s: 5V Industrial Backplane Glue Logic, Legacy Microprocessor Address Decoding, Asynchronous State Machines in Telecom & Instrumentation, Peripheral Interface Adapters (GPIB, SCSI, IEEE-488), Refresh / Replacement of End-of-Life MAX 5000 Designs, Embedded Control & Legacy Industrial PLC I/O.
5V Industrial Backplane Glue Logic
The EPM5192LC1's 192 macrocells and 64 I/O pins at 5V CMOS levels match legacy industrial backplane requirements where TTL-compatible signaling and deterministic timing are essential. The 40 ns tPD and 50 MHz fMAX comfortably handle bus decoding, interrupt steering, and chip-select generation for backplane cards. Its 7 dedicated inputs simplify clock/reset distribution without burning macrocell resources, while the PQCC84 footprint has been used in production backplanes for decades.
おすすめ
Legacy Microprocessor Address Decoding
The EPM5192LC1 is well matched to address decoding for 8086, 68000, Z80, and similar legacy microprocessors, replacing multiple PAL/GAL devices with a single 192-macrocell CPLD. Its wide input fan-in via 7 dedicated pins plus 64 I/O accommodates full 20-24 bit address buses and 8-16 bit data-path control logic. Deterministic 40 ns propagation delay guarantees clean chip-select timing across read/write cycles without metastability risk in asynchronous designs.
おすすめ
Asynchronous State Machines in Telecom & Instrumentation
Telecom and instrumentation front-ends rely on asynchronous state machines for protocol handling, line-interface control, and measurement sequencing where the EPM5192LC1's MAX 5000 fabric excels. The 50 MHz fMAX supports fast state transitions while the CMOS EPROM technology provides instant-on, non-volatile configuration that survives power loss. The 5 V supply and TTL I/O levels simplify interfacing with ECL-to-TTL translators and front-panel switch matrices.
おすすめ
Peripheral Interface Adapters (GPIB, SCSI, IEEE-488)
The EPM5192LC1 implements byte-control and handshaking logic for legacy peripheral interfaces such as GPIB (IEEE-488), SCSI, and parallel port adapters. Its 192 macrocells handle full state machines for talker/listener arbitration, NRZ encoding, and REQ/ACK handshaking, while 64 I/O pins map cleanly to 8-bit data plus control nets. The 5 V TTL I/O and PQCC84 footprint match the original GPIB controller reference designs still in production today.
おすすめ
Refresh / Replacement of End-of-Life MAX 5000 Designs
Many long-lifecycle aerospace, defense, and industrial programs still depend on the original MAX 5000 footprint, and the EPM5192LC1 is the pin-compatible OTP production part to keep those boards running. The PQCC84 land pattern, JEDEC S-PQCC-J84 outline, and 192-macrocell count are identical to the original qualification baseline. Where the LC1 plastic OTP variant is the production fit, the JC84-1 windowed ceramic variant supports the same footprint for field re-programming.
おすすめ
Embedded Control & Legacy Industrial PLC I/O
The EPM5192LC1 supports embedded control blocks such as legacy PLC digital I/O expansion, encoder-counter decoding, and isolated relay-driver sequencing, where its 64 I/O pins interface directly to 5 V logic families and opto-isolators. The 192-macrocell capacity lets designers integrate scan-matrix, debounce, and PWM generation into one CPLD, eliminating multiple 22V10/16V8 PALs. The OTP plastic LC package is suitable for high-volume factory-floor production.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: EPM5192LC1 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | EPM5192LC-1 | EPM5192JC84-1 | EPM5192GC84-1 | EPM5192LC | EPM5192LC-2 |
|---|---|---|---|---|---|---|
| Package | PQCC-84 (S-PQCC-J84) | PQCC-84 (S-PQCC-J84) | PQCC-84 (S-PQCC-J84) | PQCC-84 (S-PQCC-J84) | PQCC-84 (S-PQCC-J84) | PQCC-84 (S-PQCC-J84) |
| Brand | Altera | Altera | Altera | Altera | Altera | Altera |
| Macrocells | 192 | 192 | 192 | 192 | 192 | 192 |
| User I/O | 64 | 64 | 64 | 64 | 64 | 64 |
| Supply Voltage | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V |
| Programming Method | OTP (plastic) | OTP (plastic) | UV-erasable (windowed ceramic) | UV-erasable (windowed ceramic) | OTP (plastic) | OTP (plastic) |
| Operating Temperature | 0 °C to 70 °C (commercial) | 0 °C to 70 °C (commercial) | 0 °C to 70 °C (commercial) | 0 °C to 70 °C (commercial) | 0 °C to 70 °C (commercial) | 0 °C to 70 °C (commercial) |
主な差別化要因
- 192 macrocells, largest in MAX 5000 family （vs EPM5064LC-1 (64 macrocells))
- 7 dedicated high-fan-in inputs （vs EPM5128JC-1 (128 macrocells, 4 dedicated inputs))
- Industry-standard PQCC84 footprint （vs EPM5192LC-2N (PQFP package))
設計ノート
Estimated: at 50 MHz with all 64 I/O toggling, the EPM5192LC1 draws roughly 200–300 mA from the 5 V supply (typical ICC at full logic activity). Place a bulk 10 µF tantalum capacitor at the board 5 V entry, then one 0.1 µF ceramic per VCC/GND pair within 5 mm of the PQCC84 leads to suppress VCC sag during simultaneous switching outputs. Use a 4-layer PCB with a dedicated ground plane; the high edge rates of 5 V CMOS outputs couple noise into VCC if decoupling is inadequate.
Route all seven dedicated inputs (GCLK, OE, CLR, and four additional dedicated pins) before any bidirectional I/O to keep clock and reset distribution paths short. Keep a continuous ground ring around the PQCC84 J-leads; via-fan the ground ring to the internal ground plane every 5 mm. Avoid running 5 V TTL signals parallel to clock traces for more than 25 mm to prevent crosstalk into the AND array, which directly impacts tPD and fMAX.
Estimated: floating I/O pins on the EPM5192LC1 may source or sink 1–2 mA each through input-protection diodes, potentially causing VCC droop. Always terminate unused I/O pins per datasheet (typically pull-up or pull-down to VCC/GND via 10 kΩ) and configure unused macrocells to default low-power mode in MAX+PLUS II. Do not exceed 5.25 V on any I/O even momentarily; the EPROM programming algorithm requires a higher voltage on specific pins that must never be applied during normal operation.
コンプライアンス情報
EPM5192LC1 is part of the legacy Altera MAX 5000 family, classified obsolete. RoHS, lead-free, halogen-free, REACH, and conflict-minerals status are not explicitly stated in the verified distributor data and should be requested from the supplier on a per-lot basis. For automotive programs, AEC-Q100 is not applicable; use the GM/883B military-grade variant instead.
