IKCM15H60GA - 600V 15A CIPOS Mini IPM | Infineon
部品番号: IKCM15H60GA ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $11.5 | $11.50 |
| 10 | $10.2 | $102.00 |
| 100 | $8.95 | $895.00 |
| 500 | $7.8 | $3,900.00 |
| 1,000 | $6.95 | $6,950.00 |
IKCM15H60GA 概要
An Intelligent Power Module (IPM) is a power semiconductor module that combines the power switches (IGBT or MOSFET), gate drivers, and protection circuitry into a single isolated package. The hierarchy is: IGBT/MOSFET -> power switch -> power module -> IPM. IPMs sit at the integration tier above discrete driver + IGBT designs, eliminating the need to design high-side/low-side bootstrap, fault feedback, and dead-time generation discretely. They are widely used in white goods, HVAC compressors, and small industrial inverters where PCB space, time-to-market, and reliability outweigh absolute BOM cost.
Key features of the IKCM15H60GA include: integrated bootstrap diodes for all three high-side channels (eliminating external bootstrap components), an integrated shunt resistor for current sensing, fully isolated DBC substrate with 2500 V isolation voltage, fault output (open-drain, active-low) for overcurrent, short-circuit, undervoltage, and over-temperature events, and 3.3 V/5 V logic-compatible Schmitt-trigger inputs. The integrated TRENCHSTOP IGBTs deliver low VCE(sat) and reduced Eoff, supporting switching frequencies up to 20 kHz in motor drive applications.
The IKCM15H60GA operates across -40C to +150C junction temperature with Tj(max) at +175C, drawing quiescent current of typically 1.6 mA from VBS. The module is a drop-in successor to the legacy IM393L6E with simplified 24-pin pinout versus 30 pins, integrating functions previously requiring external VTH and RFE components. Power management ICs in this voltage/current class typically use 24-pin DIP (36 x 21 mm) housings with mounting tabs for screw attachment to the heatsink.
Typical applications include BLDC and PMSM motor drives in washing machines, refrigerator compressors, HVAC fans, small industrial pumps, and servo motor control. The 15 A current rating and 600 V blocking voltage make it suitable for universal-input (100-240 VAC) rectified to 340 V DC bus operation. Compared with discrete IGBT + gate driver solutions, the IKCM15H60GA reduces PCB area by approximately 40% and cuts BOM count by 25-30 components per phase. In fan and pump drives, the integrated over-temperature shutdown and short-circuit detection protect the system without external sensors, while the open emitter configuration enables both single-shunt and leg-shunt current-sensing topologies.
ドロップイン代替品: IKCM15H60GA — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
クイック比較ツール — 並列比較する代替部品を選択:
IKCM20H60GA
✅ ドロップイン📋 参考代替品（カタログ未掲載）
IKCM10H60GA
✅ ドロップイン📋 参考代替品（カタログ未掲載）
IKCM15H60GAXKMA2
✅ ドロップイン📋 参考代替品（カタログ未掲載）
IM393L6E
✅ ドロップイン📋 参考代替品（カタログ未掲載）
IKCM15H60GA 最大定格＆電気的特性
| トポロジー | 3-phase inverter (6 IGBTs + 6 freewheeling diodes) |
| Technology | TRENCHSTOP IGBT with open emitter |
| Collector-Emitter Voltage (VCE) | 600 V |
| Continuous Collector Current (IC at TC=25C) | 15 A |
| Continuous Collector Current (IC at TC=80C) | 10 A |
| Repetitive Peak Collector Current (ICRM) | 30 A (tp=1 ms) |
| DC-Link Voltage (Bus) | 450 V maximum |
| Isolation Voltage (Visol) | 2500 V RMS (50 Hz, 1 min) |
| Output Power (recommended, fan drive) | 1.5 kW maximum |
| Switching Frequency (recommended) | up to 20 kHz |
| Short-Circuit Withstand Time | 6 us minimum |
| Quiescent Current VBS (Iqbs) | 1.6 mA typical |
| Logic Input Voltage Compatibility | 3.3 V / 5 V (LSTTL/CMOS, Schmitt-trigger) |
| Internal Pull-Down Resistor on LIN/HIN | 5 kohm typical |
| Bootstrap Diode | Integrated |
| Junction Temperature Range (Tj) | -40C to +150C (operating), +175C (maximum) |
| Storage Temperature Range (Tstg) | -40C to +125C |
| Mounting Torque | 0.6 N.m (M3 screw) |
| パッケージ | 24-pin DIP (36 x 21 mm) Power Module with offset leads |
| RoHS ステータス | Compliant |
IKCM15H60GA ピン構成
| ピン 1 | VTH — Thermistor voltage reference / analog temperature output |
| ピン 2 | GND — Logic ground / low-side emitter return |
| ピン 3 | ITRIP — Current trip threshold programming input (internal shunt) |
| ピン 4 | VCC — +15V low-side gate drive supply |
| ピン 5 | FO — Fault output (open-drain, active-low) |
| ピン 6 | EN — Enable input (active-high) |
| ピン 7 | LINU — Low-side gate input, phase U |
| ピン 8 | LINV — Low-side gate input, phase V |
| ピン 9 | LINW — Low-side gate input, phase W |
| ピン 10 | HINU — High-side gate input, phase U |
| ピン 11 | HINV — High-side gate input, phase V |
| ピン 12 | HINW — High-side gate input, phase W |
| ピン 13 | VBSU — Bootstrap supply, phase U high-side |
| ピン 14 | VBSV — Bootstrap supply, phase V high-side |
| ピン 15 | VBSW — Bootstrap supply, phase W high-side |
| ピン 16 | DC+ — DC-link positive bus input |
| ピン 17 | U — Phase U output (open emitter) |
| ピン 18 | V — Phase V output (open emitter) |
| ピン 19 | name — [DATA_NEEDED: detailed description for pin 19] |
| ピン 20 | P — [DATA_NEEDED: detailed description for pin 20] |
| ピン 21 | NC — Not connected (per datasheet) |
| ピン 22 | NC — Not connected (per datasheet) |
| ピン 23 | NC — Not connected (per datasheet) |
| ピン 24 | NC — Not connected (per datasheet) |
Forward Bias 安全動作領域 (FBSOA)
主な用途
IKCM15H60GA の用途: 6 件s: BLDC Motor Drive - Washing Machine Drum Motor, Refrigerator Compressor IPM, HVAC Fan and Blower Drives, Small Industrial Pumps and Circulators, Servo Motor Control, EV Charging Auxiliary Modules.
BLDC Motor Drive - Washing Machine Drum Motor
The IKCM15H60GA's 600 V / 15 A rating and integrated 3-phase inverter make it ideal for direct-drive washing machine BLDC drum motors in 1.0-1.5 kW class. The integrated shunt resistor enables single-shunt FOC control typical of modern inverter drum drives, while the 2500 V isolation and built-in over-temperature/short-circuit protection handle the harsh vibration and moisture environment under the tub. The 36 x 21 mm DIP package mounts directly on the chassis-attached heatsink, eliminating separate driver PCBs. Compared with discrete IGBT + IR2136 driver designs, the IKCM15H60GA reduces inverter PCB area by 40% and BOM count by 25+ components per motor.
おすすめ
Refrigerator Compressor IPM
Variable-speed refrigerator compressors in the 100-400 W class operate from 100-240 VAC rectified to 170-340 VDC, perfectly matching the IKCM15H60GA's 600 V / 15 A envelope with significant headroom. The CIPOS Mini's integrated bootstrap diodes eliminate 6 external diodes plus their charge-pump circuitry, while the open-emitter configuration supports leg-shunt current sensing for smooth sinusoidal FOC. At TC=80C continuous current of 10 A, the module drives compressors up to ~400 W without derating. Built-in fault output directly interfaces with the appliance's safety MCU, providing UL 250 compliance for compressor stall and overcurrent events without external protection circuits.
おすすめ
HVAC Fan and Blower Drives
Indoor unit fans in HVAC systems (1.0-1.5 kW BLDC class) require quiet, variable-speed control from 100-240 VAC, an ideal operating point for the IKCM15H60GA. The 20 kHz switching capability moves switching noise above the audible range, while the low-Eoff TRENCHSTOP IGBTs minimize acoustic noise and reduce EMI filter cost. The integrated fault output (open-drain active-low) feeds directly to the HVAC controller's interrupt pin, providing UL 1995 compliant protection against rotor lock, overcurrent, and overheating. The compact 36 x 21 mm DIP module enables slim indoor unit designs where vertical PCB space is constrained, and the offset leads simplify screw-down heatsink mounting without bending I/O traces.
おすすめ
Small Industrial Pumps and Circulators
Circulator pumps for residential hydronic heating, solar water heating, and small industrial fluid handling require 3-phase motor drives up to 1.5 kW from single-phase mains via a rectifier stage. The IKCM15H60GA's 600 V blocking voltage handles rectified 240 VAC with generous 2x margin, and the 15 A continuous rating covers pumps with inrush surge up to 30 A repetitive peak. The module's over-temperature protection at 150C junction plus 2500 V isolation complies with IEC 60335 (household appliance safety) for water-pump applications. The integrated shunt enables precise torque control for constant-flow pump algorithms, while the open emitter topology supports sensorless back-EMF operation for cost-sensitive models.
おすすめ
Servo Motor Control
Small servo drives for robotics, CNC spindles, and automated machinery (1.0-1.5 kW range) benefit from the IKCM15H60GA's low switching losses and high-bandwidth current sensing. The integrated shunt resistor combined with open-emitter output enables 20 kHz current loop sampling for high-dynamic servo control, while the 600 V / 15 A envelope covers 200-240 VAC input servos. The module's fault output with 6 us short-circuit detection protects expensive servo motors from catastrophic winding shorts, and the 2500 V isolation provides safe separation between logic and power stages in industrial cabinet environments. Compatible with 3.3 V MCUs, the module pairs directly with modern servo controllers running FOC with field-weakening for high-speed spindle operation.
おすすめ
EV Charging Auxiliary Modules
While not suitable for the main traction inverter, the IKCM15H60GA fits well in auxiliary 3-phase motor drives within EV charging stations and battery thermal management systems - specifically the coolant pumps and HVAC blowers in 800 V battery architectures (where the 600 V rating covers the auxiliary DC-link). The module's AEC-Q100 qualification status is not applicable (industrial grade), so designers must qualify it for automotive use separately, but its robust fault protection and 150C junction rating suit under-hood thermal management pump drives. The integrated bootstrap and shunt reduce auxiliary inverter BOM, which is critical for cost-sensitive thermal management systems across EV platforms.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: IKCM15H60GA — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | IKCM20H60GA | IKCM10H60GA | IKCM15H60GAXKMA2 | IM393L6E |
|---|---|---|---|---|---|
| Brand | Infineon | Infineon | Infineon | Infineon | Infineon |
| Package | 24-pin DIP (36x21) | 24-pin DIP (36x21) - same | 24-pin DIP (36x21) - same | 24-pin DIP (36x21) - same | 30-pin DIP (36x21) - larger body |
| Collector-Emitter Voltage | 600 V | 600 V | 600 V | 600 V | 600 V |
| Continuous Collector Current (TC=25C) | 15 A | 20 A | 10 A | 15 A | 15 A |
| Output Power (fan drive) | 1.5 kW | 2.2 kW | 1.0 kW | 1.5 kW | 1.5 kW |
| Pin Count | 24 | 24 | 24 | 24 | 30 |
| Bootstrap Diodes | Integrated | Integrated | Integrated | Integrated | Integrated |
| Current Sense | Integrated shunt | Integrated shunt | Integrated shunt | Integrated shunt | Integrated shunt |
| RoHS Compliance | Yes | Yes | Yes | Yes | Yes |
主な差別化要因
- Higher continuous current rating in same CIPOS Mini family （vs IKCM10H60GA)
- Integrated bootstrap diodes eliminate 6 discrete components （vs IM393L6E (legacy predecessor))
- Simplified 24-pin pinout vs legacy 30-pin design （vs IM393L6E (legacy predecessor))
設計ノート
Estimated: At IC=10 A continuous, VCE(sat)=1.6 V, and 16 kHz switching with E_total ~2.5 mJ per cycle, per-module dissipation is approximately 18 W steady state (P_cond = 10x1.6 = 16 W + P_sw = 2x18x16kHz/1000 = 0.6 W). With Rth(j-f)=1.0 C/W, the heatsink must keep TC below 80C in 25C ambient, requiring heatsink thermal resistance below ~2.5 C/W. Apply thermal grease with thermal pad rated at <0.1 C-in2/W and torque M3 mounting screws to 0.6 N.m per Infineon's datasheet mechanical specifications.
Keep the DC-link bus capacitor (typically 1-2 uF X2 + 220-470 uF electrolytic) within 30 mm of the module's DC+ pin (pin 16) to minimize stray inductance that causes overvoltage spikes at IGBT turn-off. Place bootstrap capacitors (typically 1-10 uF ceramic) close to VBSU/VBSV/VBSW pins (13/14/15) with short traces to their respective phase output pins to ensure proper high-side gate drive. The logic ground (pin 2) must connect to the controller's ground plane separately from power grounds - use a star-ground topology at pin 2 to avoid ground bounce during high di/dt switching events.
Do not exceed the 6 us short-circuit withstand time window - configure the controller's overcurrent protection to trigger shutdown well within this window. Do not apply logic signals to LIN/HIN pins before VCC reaches 13V minimum or the module may enter undefined states; sequence power-up VCC first, then enable, then PWM. Do not exceed 2500 V isolation between power and logic sides - provide at least 8 mm creepage on PCB between high-voltage DC+ bus and logic traces. Finally, do not skip the external TVS diode across VCC - transients above 18V will damage the gate drive IC.
コンプライアンス情報
RoHS compliant per Infineon product page. Not AEC-Q100 qualified - industrial grade IPM. Conflict minerals compliant per Infineon supplier declaration.
