MC33993DWBR2 - 22-Ch Switch Detection Interface | NXP
部品番号: MC33993DWBR2 ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $4.92 | $4.92 |
| 10 | $4.43 | $44.30 |
| 100 | $3.94 | $394.00 |
| 500 | $3.55 | $1,775.00 |
| 1,000 | $3.16 | $3,160.00 |
| 3,000 | $2.78 | $8,340.00 |
MC33993DWBR2 概要
A Multiple Switch Detection Interface (MSDI) is a type of specialized automotive interface IC that scans multiple mechanical or electronic switch inputs and reports their state to a microcontroller. It belongs to the broader hierarchy of interface ICs -> communication ICs -> automotive semiconductors, and is engineered to replace discrete pull-ups and multiplexing circuits with a single robust solution. This category of IC dramatically reduces wiring harness complexity in body control modules by allowing many switches to share a common return path.
Key features include 22 input channels with programmable wetting current (typically 1 mA, 6 mA, or 16 mA selectable via SPI), built-in debounce timers, an analog-to-digital mode for ratiometric measurement, an interrupt output to wake the host MCU on state change, and robust automotive transient immunity. The 32-pin SOIC W (DWB) package supports -40C to +125C automotive operating temperature range and is qualified per AEC-Q100 standards.
The MC33993 uses a sequential scanning architecture where each switch input is multiplexed through an internal analog front-end, then compared to programmable thresholds. The SPI register map provides status, configuration, and interrupt control. Two programmable wetting current sources ensure reliable operation with both dry-contact and electronic switches by preventing contact oxidation.
Typical applications include automotive body control modules for window switches, door lock and mirror controls, steering wheel button clusters, HVAC control panels, and seat adjustment switches. The device replaces discrete resistor networks and dozens of MCU pins, freeing the host processor for higher-level functions while maintaining low quiescent current (<=100 uA typical standby).
When designing with this part, ensure the SPI master clock does not exceed 8 MHz and configure wetting current to match the switch contact type. For battery-connected applications, add reverse-battery and load-dump protection per system requirements.
This page synthesizes drop-in alternatives, parametric comparison data, and practical design notes not found in the manufacturer datasheet alone.
ドロップイン代替品: MC33993DWBR2 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
クイック比較ツール — 並列比較する代替部品を選択:
MC33993DWB
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
MC33993DWBR2G
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
MC33993DWBR2 最大定格＆電気的特性
| 機能 | Multiple Switch Detection Interface (MSDI) |
| Number of Switch Inputs | 22 channels |
| インターフェース | SPI (Serial Peripheral Interface) |
| Maximum SPI Clock | 8 MHz |
| Supply Voltage Range | 5.5 V to 26 V (4.5 V to 5.5 V with SPI-configured mode) |
| Wetting Current (programmable) | 1 mA / 6 mA / 16 mA (SPI-selectable) |
| 動作温度範囲 | -40 C to +125 C (automotive) |
| パッケージ | 32-pin SOIC W (DWB), 7.5 x 11 mm body |
| 実装タイプ | Surface Mount |
| Packaging | Tape & Reel (R2 suffix) |
| AEC-Q100 Qualification | Qualified |
| RoHS ステータス | Compliant |
| Lead-Free | Yes |
| Interrupt Output | Yes (active-low INTB) |
| Switch Debounce | Programmable via SPI |
MC33993DWBR2 ピン構成
| ピン 1 | VBAT — Battery supply input (5.5 V to 26 V) |
| ピン 2 | GND — Ground return |
| ピン 3 | VDD — Logic supply (4.5 V to 5.5 V) |
| ピン 4 | CS — SPI chip select (active low) |
| ピン 5 | SCLK — SPI serial clock input |
| ピン 6 | MOSI — SPI master-out / slave-in data |
| ピン 7 | MISO — SPI master-in / slave-out data |
| ピン 8 | INTB — Interrupt output (active low) |
| ピン 9 | RSTB — Reset input (active low) |
| ピン 10 | SP0 — Switch input channel 0 |
| ピン 11 | SP1 — Switch input channel 1 |
| ピン 12 | SP2 — Switch input channel 2 |
| ピン 13 | SP3 — Switch input channel 3 |
| ピン 14 | SP4 — Switch input channel 4 |
| ピン 15 | SP5 — Switch input channel 5 |
| ピン 16 | SP6 — Switch input channel 6 |
| ピン 17 | SP7 — Switch input channel 7 |
| ピン 18 | SP8 — Switch input channel 8 |
| ピン 19 | SP9 — Switch input channel 9 |
| ピン 20 | SP10 — Switch input channel 10 |
| ピン 21 | SP11 — Switch input channel 11 |
| ピン 22 | SP12 — Switch input channel 12 |
| ピン 23 | SP13 — Switch input channel 13 |
| ピン 24 | SP14 — Switch input channel 14 |
| ピン 25 | SP15 — Switch input channel 15 |
| ピン 26 | SP16 — Switch input channel 16 |
| ピン 27 | SP17 — Switch input channel 17 |
| ピン 28 | SP18 — Switch input channel 18 |
| ピン 29 | SP19 — Switch input channel 19 |
| ピン 30 | SP20 — Switch input channel 20 |
| ピン 31 | SP21 — Switch input channel 21 |
| ピン 32 | NC — Not connected (per datasheet) |
主な用途
MC33993DWBR2 の用途: 7 件s: Automotive Body Control Module (BCM), Power Window and Door Lock Switch Panel, Steering Wheel Button Cluster Interface, HVAC Control Panel Input Reading, Seat Adjustment and Memory Module, Industrial Control Panel Switch Aggregation, Agricultural and Heavy Equipment Cab Controls.
Automotive Body Control Module (BCM)
The MC33993DWBR2 is purpose-built for automotive body control modules that aggregate switch inputs from door panels, liftgates, and instrument clusters. With 22 channels and AEC-Q100 qualification, it directly interfaces to wet and dry switch contacts across the 12V battery bus while offloading scan and debounce duties from the host MCU. Its 8 MHz SPI bus keeps communication overhead low, allowing the MCU to handle higher-level body control logic.
おすすめ
Power Window and Door Lock Switch Panel
Door-mounted switch panels for power windows, mirror adjustment, and door locks typically expose 8-16 SPDT contacts routed through a wiring harness to the BCM. The MC33993DWBR2 reads all 22 possible inputs through its multiplexed analog front-end, applies programmable wetting current to prevent contact oxidation, and reports state changes over SPI to the central body controller - eliminating dozens of harness wires per door.
おすすめ
Steering Wheel Button Cluster Interface
Modern steering wheels carry 8-20 button inputs for audio, cruise control, phone, and ADAS functions. The MC33993DWBR2 reads these switches through a single SPI connection running across the clockspring, dramatically reducing wiring complexity versus discrete pull-up designs. Its <100 uA standby current allows the steering wheel to remain powered in accessory mode without draining the battery.
おすすめ
HVAC Control Panel Input Reading
HVAC head units combine rotary encoders, push buttons, and backlit indicators that historically required dedicated MCU pins. The MC33993DWBR2 replaces 22 of these discrete inputs with a single SPI-scanned interface, freeing the host MCU's GPIO for LED drivers and display control. Its analog mode also supports ratiometric reading of temperature selectors and mode switches.
おすすめ
Seat Adjustment and Memory Module
Power seat modules expose 8-16 switches for position, lumbar, and memory presets that must operate reliably through years of mechanical wear. The MC33993DWBR2's programmable wetting current prevents oxidation on seat switch contacts, while its SPI interrupt output wakes the seat controller only on state change, minimizing quiescent draw in parked vehicles with active seat memory.
おすすめ
Industrial Control Panel Switch Aggregation
Outside automotive, the MC33993DWBR2 is well-suited to industrial control panels that aggregate many limit switches, selector switches, and E-stop contacts into a single SPI-reporting interface. Its wide 5.5V to 26V supply tolerance matches 24V industrial rails, while AEC-Q100 grade transient immunity ensures reliable operation in factory environments with motor-drive EMI.
おすすめ
Agricultural and Heavy Equipment Cab Controls
Tractors and construction equipment cabs carry dozens of switch inputs for PTO, hydraulics, and transmission controls routed through vibration-prone wiring harnesses. The MC33993DWBR2's 26V supply tolerance and AEC-Q100 automotive qualification make it robust enough for these off-road environments, while its multiplexed SPI interface simplifies the harness from cab to body controller.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MC33993DWBR2 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MC33993DWB | MC33993DWBR2G |
|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 32-pin SOIC W (DWB) | 32-pin SOIC W (DWB) - same | 32-pin SOIC W (DWB) - same |
| Switch Inputs | 22 channels | 22 channels | 22 channels |
| SPI Clock Max | 8 MHz | 8 MHz | 8 MHz |
| Supply Voltage Range | 5.5 V to 26 V | 5.5 V to 26 V | 5.5 V to 26 V |
| Wetting Current Options | 1 / 6 / 16 mA | 1 / 6 / 16 mA | 1 / 6 / 16 mA |
| AEC-Q100 Qualified | Yes | Yes | Yes |
| Operating Temperature | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C |
| Packaging Format | Tape & Reel (R2) | Tube / Tray | Tape & Reel (lead-free) |
| Lead-Free / RoHS | Yes | Yes | Yes (green) |
主な差別化要因
- Integrated programmable wetting current in three ranges （vs Discrete resistor + MCU ADC design)
- 22 channels with single SPI connection （vs Discrete multiplexer ICs)
- AEC-Q100 qualification and 26V VBAT tolerance （vs Industrial-only switch interface ICs)
設計ノート
Place a 100 nF decoupling capacitor as close as possible to the VDD pin (4.5V to 5.5V logic supply) and a 10 uF bulk capacitor on the VBAT pin to suppress automotive load-dump transients. Keep SPI traces short and route them over a continuous ground plane; the SOIC W package benefits from a copper pour on pin 2 (GND) to provide thermal relief and a low-impedance return path for the wetting current sources.
Do not exceed 26V on VBAT without external TVS protection; the absolute maximum rating allows brief transients but sustained overvoltage will damage the part. Ensure the SPI CS pin returns high between transactions, and that the host MCU respects the INTB pin polarity (active-low open-drain requires an external pull-up to VDD). Misconfiguring the wetting current register can cause switch contact welding - always default to 1 mA until SPI control is verified.
Route the 22 switch inputs (SP0-SP21) as short, parallel traces to minimize capacitance imbalance across the multiplexer. For noisy environments, add 10 kohm series resistors and 100 pF filter caps at each input to suppress RF injection. Avoid routing switch traces near high-current motor driver outputs (e.g., MC33926) to prevent conducted coupling into the analog front-end.
コンプライアンス情報
RoHS and lead-free per NXP product page. AEC-Q100 qualified for automotive applications. Halogen-free per Freescale/NXP product family declaration.
