MC9S12D32MFUE - 16-Bit 25MHz HCS12 MCU | NXP | Automotive
部品番号: MC9S12D32MFUE ✗ 生産終了| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $26.4032 | $26.40 |
| 10 | $26.4032 | $264.03 |
| 100 | $26.4032 | $2,640.32 |
| 500 | $26.4032 | $13,201.60 |
| 1,000 | $26.4032 | $26,403.20 |
MC9S12D32MFUE 概要
A microcontroller is a programmable semiconductor that executes firmware, reads sensors, controls actuators, and coordinates peripheral devices. The HCS12 core belongs to the MCU hierarchy and combines a 16-bit processor with integrated memory and communications interfaces. Rather than requiring separate interface controllers, the MC9S12D32MFUE places CAN, serial, SPI, timing, and watchdog resources beside the CPU.
Verified product data identifies 32 KB of flash organized as 32K x 8, 4K x 8 bytes of RAM, 1K x 8 bytes of EEPROM, and 59 I/O pins. Its communication set includes CANbus, I2C, SCI, and SPI, while PWM supports time-dependent output functions and the watchdog helps protect embedded operation. The part also supports both 2.5 V and 5 V operation according to the supplied comparison data.
The S12D architecture provides full 16-bit internal data paths and an external bus that can operate in an 8-bit narrow mode for lower-cost memory interfacing. That combination allows engineers to retain 16-bit processing internally while connecting narrower external devices where appropriate. System integration resources managed by the SIM include clock generation, interrupt control, and bus interfacing.
Typical uses include automotive body and chassis controllers, motor-control equipment, industrial automation, CAN-connected sensors, and compact embedded control panels. The 80-QFP footprint supports conventional PCB assembly, while the broad peripheral set can reduce component count in systems that otherwise require separate communication and timing ICs.
Design planning must verify exact pin multiplexing, clock setup, memory interfaces, and peripheral electrical limits against the official datasheet before layout. Because the official NXP page identifies the lifecycle state as NRND, long-lived production programs should confirm availability, migration timing, and any approved replacement strategy before committing new designs.
This page consolidates verified distributor specifications, lifecycle information, sourcing data, and practical engineering considerations for the MC9S12D32MFUE. It also separates documented facts from unavailable electrical details, helping engineers evaluate this NRND 16-bit MCU without assuming unverified pinout, supply-voltage, or timing parameters.
ドロップイン代替品: MC9S12D32MFUE — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: MC9S12D32MFUE （同一形状・フットプリント） — 相違点: Package, ADC, Supply Voltage, Connectivity, EEPROM.
クイック比較ツール — 並列比較する代替部品を選択:
MC9S12D32VFUE
✅ ドロップイン✓ 在庫あり
$10.32 / 個
データシートを見る →MC9S12GC32CFUE
✅ ドロップイン📋 参考代替品（カタログ未掲載）
MC9S12D64MFUER
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$1.0524 / 個
データシートを見る →MC9S12D32MFUE 最大定格＆電気的特性
| Processor Core | HCS12 |
| Processor Series | S12D |
| データバス幅 | 16 bit |
| 最大クロック周波数 | 25 MHz |
| Program Memory Size | 32 KB (32K x 8) |
| Program Memory Type | Flash |
| RAM Size | 4K x 8 bytes |
| EEPROM Size | 1K x 8 bytes |
| Number of I/O | 59 |
| Connectivity | CANbus, I2C, SCI, SPI |
| Peripherals | PWM, WDT |
| Operating Voltage | 2.5 V / 5 V |
| パッケージ | 80-QFP (14 x 14 mm) |
| ピン数 | 80 pins |
| 実装タイプ | Surface Mount |
| ライフサイクル状態 | NRND |
| RoHS | Not stated in verified data |
MC9S12D32MFUE 80-qfp (14 x 14 mm) ピン配置ガイド
MC9S12D32MFUE (80-qfp (14 x 14 mm) パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: MC9S12D32MFUE.
詳細は データシート をご参照ください。
主な用途
MC9S12D32MFUE の用途: 6 件s: Automotive Body Control, CAN-Connected Industrial Control, Motor and PWM Control, Sensor and Conditioning Hub, Communication Gateway, Test and Measurement Equipment.
Automotive Body Control
The MC9S12D32MFUE fits body-control modules because its HCS12 core operates up to 25 MHz and combines 59 I/O pins with CANbus, PWM, SCI, and watchdog resources in one 80-QFP device. A controller can acquire switch and sensor inputs, apply vehicle logic, drive actuators, and report status over CAN. Its 32 KB flash supports embedded firmware while 4K x 8 bytes of RAM handles working state. Because the official page marks the MCU NRND, an automotive program should also confirm qualification documentation and secure lifecycle supply.
おすすめ
CAN-Connected Industrial Control
The integrated CANbus, SCI, SPI, and I2C interfaces make MC9S12D32MFUE useful for distributed industrial equipment that must coordinate sensors and actuators. Its 25 MHz HCS12 core can execute control logic while the 59 available I/O handle discrete inputs and outputs. The external bus can also operate in an 8-bit narrow mode according to the supplied comparison data, allowing lower-cost memory interfacing where appropriate. Firmware must verify timing, bus arbitration, termination, and peripheral multiplexing against the manufacturer datasheet.
おすすめ
Motor and PWM Control
MC9S12D32MFUE can serve as the supervisory controller for motors, valves, lamps, and other PWM-controlled loads because PWM is included among its documented peripherals. Its 16-bit data paths support efficient fixed-width processing, while the 25 MHz clock provides headroom for control-loop execution and peripheral scheduling. Designers should treat the available I/O and PWM resources as muxed and confirm channel counts, timer frequencies, output levels, and fault-handling requirements in the official datasheet before assigning pins.
おすすめ
Sensor and Conditioning Hub
The SPI and I2C interfaces of the MC9S12D32MFUE allow a compact controller to collect data from sensors, converters, and external memory without dedicating separate logic to each bus. Its 4K x 8 bytes of RAM and 1K x 8 bytes of EEPROM provide working and nonvolatile configuration storage, while the 32 KB flash holds application code. Because no detailed ADC, analog, or sensor-interface specifications were supplied, analog signal conditioning and sensor selection require separate engineering validation.
おすすめ
Communication Gateway
MC9S12D32MFUE is suitable for a protocol gateway that bridges CANbus with SCI, SPI, or I2C equipment because several serial interfaces are integrated around the HCS12 CPU. The 80-QFP package provides a conventional surface-mount option with 59 stated I/O pins, and 32 KB flash can hold protocol conversion and diagnostics. Real designs must budget bus timing, isolation, protection, connector routing, and firmware state space carefully; verified source data does not specify transceiver models or detailed electrical thresholds.
おすすめ
Test and Measurement Equipment
A 25 MHz HCS12 microcontroller with flash, EEPROM, watchdog, PWM, and multiple serial buses can coordinate automated test fixtures and measurement controllers. MC9S12D32MFUE can manage sequencing, fixture control, data transfer, and fault recovery while its external bus supports system integration. The supplied evidence does not specify analog accuracy, operating-temperature limits, or ADC performance, so precision-instrument designs should not assume suitability without reviewing the complete electrical specification and application requirements.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MC9S12D32MFUE — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MC9S12D32VFUE | MC9S12GC32CFUE | MC9S12D64MFUER |
|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
主な差別化要因
- Verified 32 KB flash configuration （vs MC9S12GC32CFUE)
- Documented 25 MHz operating class （vs MC9S12GC32CFUE)
- Broad integrated communication set （vs MC9S12GC32CFUE)
設計ノート
Do not treat an 80-pin package as proof of drop-in compatibility. Before substituting MC9S12D32VFUE, MC9S12GC32CFUE, or MC9S12D64MFUER, compare every power pin, ground pin, reset connection, debug interface, clock source, communication pin, and multiplexed peripheral signal against the manufacturer pin-assignment tables. The supplied comparison records do not establish complete pin-level equivalence, so board and firmware qualification remains mandatory.
The verified comparison data identifies 2.5 V and 5 V operation, but it does not provide individual I/O-domain limits, regulator requirements, or absolute maximum ratings. Determine the actual supply topology and signal levels from the official datasheet before connecting external devices. Include local decoupling at the MCU supply pins and preserve routing flexibility for filtering and debug instrumentation.
The MC9S12D32MFUE uses an 80-QFP package with a stated 14 x 14 mm body. Follow the manufacturer's land-pattern and solder-mask recommendations rather than treating all 80-QFP packages as identical. Preserve access to programming and debug signals, route sensitive clocks away from high-current switching paths, and place decoupling capacitors close to their intended supply pins using short ground returns.
Because the official NXP page marks MC9S12D32MFUE NRND, inventory visibility should not be treated as a long-term supply guarantee. Track product-change notices, record approved manufacturer sources, and qualify enough stock for repair and maintenance cycles. New designs should begin a migration assessment rather than allowing an NRND MCU to become the default choice for another long-life platform.
コンプライアンス情報
The supplied sources identify the part as automotive-related but do not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. These fields remain unknown rather than inferred.
