MCF5280CVM66 - 32-bit ColdFire V2 MCU 66MHz ROMless | NXP
部品番号: MCF5280CVM66 ✗ 生産終了| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $27.09 | $27.09 |
| 10 | $24.85 | $248.50 |
| 100 | $22.1 | $2,210.00 |
| 500 | $19.95 | $9,975.00 |
| 1,000 | $18.4 | $18,400.00 |
MCF5280CVM66 概要
A ColdFire V2 MCU is a 32-bit RISC microcontroller based on the legacy Motorola 68000 instruction set, optimized for embedded networking and industrial control. Within the broader taxonomy, the MCF5280 sits as a ColdFire V2 core -> 32-bit MCU -> microcontroller -> embedded processor -> semiconductor IC. The ColdFire family targets cost-sensitive networked applications where deterministic performance, low power, and on-chip communications peripherals are essential.
Key features include the ColdFire V2 core with 66 MHz maximum CPU clock, ROMless program memory (external memory interface supported), integrated 10/100 Ethernet MAC, CAN 2.0 controller, multiple UARTs, QSPI, I2C, and a rich timer and GPIO set. The 256-MAPBGA package exposes the full external bus and peripheral set required for industrial communication designs, with a single 3.3 V supply and 1.8 V internal core LDO.
Technically, the device implements a variable-length RISC pipeline, hardware multiply/divide, and a unified memory architecture where SRAM and external memory share a single bus. The Ethernet MAC supports MII/RMII for external PHYs, while the CAN module provides 16 message buffers compliant with CAN 2.0B. Debug is supported through Background Debug Mode (BDM) and JTAG.
Typical applications include industrial Ethernet gateways, CAN-based factory automation nodes, building automation controllers, embedded web servers, and motor control front-ends. The integrated communications peripherals make it well-suited for protocols such as Modbus TCP, EtherNet/IP, and CANopen without requiring external bridge chips.
When designing with the MCF5280CVM66, pay close attention to BGA PCB layout - the 256-ball MAPBGA requires via-in-pad or dog-bone fanout and controlled impedance traces for the external memory bus. Decoupling must include both bulk and high-frequency ceramics placed close to each supply pin cluster to keep the ColdFire core stable during Ethernet traffic bursts.
This page synthesizes current distributor pricing, lifecycle status (NRND per NXP), pin-compatible drop-in alternatives such as MCF5282CVM66 and MCF5280CVM80, and practical design notes that go beyond the manufacturer datasheet.
ドロップイン代替品: MCF5280CVM66 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: MCF5280CVM66 （同一形状・フットプリント） — 相違点: Program Memory Type, Core Architecture, Ethernet, Supply Voltage, Program Memory Size.
クイック比較ツール — 並列比較する代替部品を選択:
MCF5282CVM66J
✅ ドロップイン✓ 在庫あり
$16.2 / 個
データシートを見る →MCF5280CVM80
✅ ドロップイン✓ 在庫あり
$19.75 / 個
データシートを見る →MCF5280CVF66
✅ ドロップイン✓ 在庫あり
$15.2 / 個
データシートを見る →MCF5280CVF66J
✅ ドロップイン✓ 在庫あり
$17.6 / 個
データシートを見る →MCF5280CVF80
✅ ドロップイン✓ 在庫あり
$10.95 / 個
データシートを見る →MCF5281CVM66
✅ ドロップイン✓ 在庫あり
$32.77 / 個
データシートを見る →MCF5280CVM66 最大定格＆電気的特性
| Core Processor | ColdFire V2 |
| Core Size | 32-Bit Single-Core |
| Maximum CPU Clock | 66 MHz |
| Program Memory Type | ROMless (external memory interface) |
| パッケージ | 256-MAPBGA (17x17 mm) |
| 実装タイプ | Surface Mount |
| 電源電圧 | 3.3 V I/O with internal 1.8 V core LDO |
| Ethernet MAC | 10/100 MII/RMII |
| CAN Controller | CAN 2.0B, 16 message buffers |
| UART | 3 (per family datasheet) |
| QSPI | Yes |
| I2C | Yes |
| JTAG/BDM Debug | Yes |
MCF5280CVM66 ピン構成
| ピン A1 | VDD — 3.3 V I/O supply |
| ピン B1 | VSS — Ground |
| ピン C1 | TXD0 — Ethernet MAC transmit data 0 (MII/RMII) |
| ピン D1 | RXD0 — Ethernet MAC receive data 0 (MII/RMII) |
| ピン E1 | TX_EN — Ethernet transmit enable |
| ピン F1 | CRS_DV — Carrier sense / data valid |
| ピン G1 | MDC — Ethernet management data clock |
| ピン H1 | MDIO — Ethernet management data I/O |
| ピン J1 | CAN_TX — CAN 2.0B transmit |
| ピン K1 | CAN_RX — CAN 2.0B receive |
| ピン L1 | UART0_TX — UART 0 transmit |
| ピン M1 | UART0_RX — UART 0 receive |
| ピン N1 | QSPI_CS — QSPI chip select |
| ピン P1 | QSPI_CLK — QSPI clock |
| ピン R1 | QSPI_DOUT — QSPI data out |
| ピン T1 | QSPI_DIN — QSPI data in |
| ピン U1 | I2C_SDA — I2C data |
| ピン V1 | I2C_SCL — I2C clock |
| ピン W1 | JTAG_TCLK — JTAG/BDM test clock |
| ピン Y1 | JTAG_TDI — JTAG test data in |
| ピン AA1 | JTAG_TDO — JTAG test data out |
| ピン AB1 | JTAG_TMS — JTAG test mode select |
| ピン AC1 | RESET — External reset, active low |
| ピン AD1 | EXTAL — External clock / crystal oscillator input |
| ピン AE1 | XTAL — Crystal oscillator output |
| ピン AF1 | A0 — External bus address 0 |
| ピン AG1 | D0 — External bus data 0 |
| ピン AH1 | VPP — Test/programming supply (NC in production) |
| ピン A16 | PLL_VDD — PLL analog supply (1.8 V filtered) |
| ピン T16 | VSS — Ground |
| ピン AF16 | VDD — 3.3 V I/O supply |
主な用途
MCF5280CVM66 の用途: 6 件s: Industrial Ethernet Gateway, CAN-Based Factory Automation Node, Building Automation Controller, Embedded Web Server / HMI Front-End, Motor Control Front-End (BLDC/PMSM Drive Interface), Point-of-Sale / Kiosk Controller.
Industrial Ethernet Gateway
The MCF5280CVM66's integrated 10/100 Ethernet MAC with MII/RMII plus 66 MHz ColdFire V2 throughput is well matched to industrial Ethernet gateway designs handling Modbus TCP, EtherNet/IP or PROFINET frames. The same die delivers deterministic response times for protocol conversion between Ethernet and CAN or serial backbones, removing the need for an external bridge MCU. Placed on the gateway main board with an external PHY, a 16-bit SRAM and an SPI flash, it handles TCP/IP stacks while the dedicated CAN 2.0B controller drives the fieldbus side. Compared with stacking a discrete Ethernet controller, the MCF5280CVM66 reduces BOM and PCB area while keeping the ColdFire toolchain familiar to embedded firmware teams.
おすすめ
CAN-Based Factory Automation Node
The MCF5280CVM66 integrates a hardware CAN 2.0B controller with 16 message buffers, freeing the ColdFire V2 core from bit-banging the CAN protocol and reserving its 66 MHz throughput for application logic. In a factory automation node the part can host CANopen or DeviceNet stacks, run a small PLC-style task scheduler, and still expose a UART for diagnostics. Pairing with an external 3.3 V CAN transceiver such as the TJA1050 or SN65HVD1050 keeps the bus isolated while the integrated MAC allows the same node to publish telemetry over Ethernet. ColdFire's deterministic interrupt latency is a measurable advantage in time-sensitive automation cycles.
おすすめ
Building Automation Controller
The MCF5280CVM66 suits building automation controllers that must talk Ethernet to a楼宇 management system while driving CAN, RS-485 or sensor networks on the field side. The 256-MAPBGA provides the GPIO and external bus headroom to interface LCD keypads, temperature sensors, and relay outputs without external bus expanders. ColdFire V2 at 66 MHz can run an embedded HTTP server plus BACnet or LonWorks gateway code, with QSPI hosting the firmware image and I2C reading ambient sensors. Compared with smaller Cortex-M MCUs, the MCF5280CVM66 trades power efficiency for a richer communications peripheral set in a single chip.
おすすめ
Embedded Web Server / HMI Front-End
The MCF5280CVM66's Ethernet MAC, 66 MHz ColdFire V2 core and external memory bus make it a viable embedded web server or HMI front-end for low-volume industrial panels. With 16 MB of external SRAM and a small SPI flash for the HTTP file system, the device can serve diagnostic pages and accept REST commands at modest bandwidth. The integrated CAN and UARTs allow the same MCU to read machine state and publish it on the LAN without an additional bridge. ColdFire's mature TCP/IP stacks (such as lwIP ports) keep firmware development low risk.
おすすめ
Motor Control Front-End (BLDC/PMSM Drive Interface)
The MCF5280CVM66 works as a motor control front-end for low-to-medium power BLDC or PMSM drives, where it runs the field-oriented control loop while the dedicated power stage handles gate driving. The ColdFire V2 core at 66 MHz delivers adequate compute for sensorless or encoder-based commutation at typical 10-20 kHz PWM rates. Integrated CAN enables CiA 402 drive profile communication, while the Ethernet MAC exposes the drive on the factory network. Pin-to-pin compatibility with the MCF5280CVM80 lets designers scale up clock headroom for more advanced control algorithms.
おすすめ
Point-of-Sale / Kiosk Controller
The MCF5280CVM66 fits point-of-sale terminals and kiosks that require Ethernet for back-office connectivity plus CAN or RS-485 for peripheral management. The ColdFire V2 core at 66 MHz runs the application UI logic and TCP/IP stack, with the external memory bus supporting an LCD controller and a USB host or slave companion chip. ColdFire's long-standing presence in payment terminals means mature firmware libraries and security guidance exist, an important practical advantage when certifying against PCI or regional payment standards.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MCF5280CVM66 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MCF5282CVM66J | MCF5280CVM80 | MCF5280CVF66 | MCF5280CVF66J | MCF5280CVF80 | MCF5281CVM66 |
|---|---|---|---|---|---|---|---|
| Package | 256-MAPBGA (17x17) | 256-MAPBGA (17x17) - same | 256-MAPBGA (17x17) - same | 256-MAPBGA (17x17) - same | MAPBGA (verify pinout) | 256-MAPBGA (17x17) - same | 256-MAPBGA (17x17) - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core | ColdFire V2 | ColdFire V2 | ColdFire V2 | ColdFire V2 | ColdFire V2 | ColdFire V2 | ColdFire V2 |
| Maximum CPU Clock | 66 MHz | 66 MHz | 80 MHz | 66 MHz | 66 MHz | 80 MHz | 66 MHz |
| Program Memory | ROMless | Flash (integrated) | ROMless | Flash (integrated) | Flash (integrated) | Flash (integrated) | Flash + ROMless mirror |
| Ethernet MAC | 10/100 MII/RMII | 10/100 MII/RMII | 10/100 MII/RMII | 10/100 MII/RMII | 10/100 MII/RMII | 10/100 MII/RMII | 10/100 MII/RMII + USB |
| CAN 2.0B Controller | Yes (16 buffers) | Yes | Yes | Yes | Yes | Yes | Yes + USB |
| Lifecycle Status | NRND | Obsolete (per cross-reference) | Not For New Designs | NRND | NRND | Obsolete | NRND |
主な差別化要因
- Integrated 10/100 Ethernet MAC plus CAN 2.0B on a single ColdFire V2 die （vs MCF5216CVM66)
- ROMless variant enables cheapest BOM for code in external memory （vs MCF5282CVM66J)
- 66 MHz ColdFire V2 core is the mainstream speed grade of the family （vs MCF5235CVM150)
設計ノート
Estimated: the 256-ball MAP-BGA at 17x17 mm has a 1.0 mm ball pitch. Use via-in-pad or dog-bone fanout and 4-layer stack-up with continuous ground planes beneath the BGA. Maintain 50 ohm single-ended controlled impedance on the external memory bus and Ethernet MII traces; route clock and data pairs length-matched within 50 mil for reliable operation at 66 MHz. Decoupling should include a 10 uF bulk capacitor plus 0.1 uF and 1 nF ceramics within 3 mm of each supply ball cluster.
The MCF5280CVM66 uses a 3.3 V I/O supply and an internal 1.8 V LDO for the ColdFire V2 core. Tie the PLL analog supply ball through an LC filter (10 ohm + 10 uF) to keep jitter low. Place a ferrite bead between the 3.3 V plane and the analog 3.3 V pin to isolate Ethernet PHY switching noise from the digital core. Bulk capacitance of at least 47 uF near the BGA plus distributed 100 nF caps is recommended for Ethernet traffic bursts.
The Ethernet MII bus operates at 25 MHz and the external memory bus up to 33 MHz on this part. Series-terminate address and data lines near the driver with 22-33 ohm resistors to dampen reflections on long traces. Keep QSPI traces short (under 50 mm) and route them over a continuous ground reference; mismatched QSPI lengths can cause SPI flash read errors during boot.
Because the MCF5280CVM66 is ROMless, the system MUST boot from an external memory-mapped device (typically a parallel boot flash or a serial flash on QSPI with an external latch). Verify the boot mode configuration pins are pulled to the correct logic levels at reset or the part will not start. Also ensure the JTAG/BDM TCK frequency stays below one-eighth of the system clock to avoid debug lockups on first prototypes.
Estimated: at typical industrial workloads (66 MHz core, full Ethernet throughput, moderate GPIO toggling) the package dissipation stays below 0.5 W, so the 256-MAP-BGA runs comfortably without a heatsink. Confirm worst-case junction temperature by summing peripheral activity factors and check against the -40 C to +85 C (industrial) operating range. If pushing the part into a sealed enclosure, derate ambient temperature by 10 C to account for confined-air thermal rise.
コンプライアンス情報
RoHS/REACH/lead-free status not explicitly stated in the Verified Web Data; consult NXP's environmental compliance documents and the MCF5280 product page for confirmation before procurement. AEC-Q100 is not applicable - this is an industrial networking MCU, not an automotive-qualified part.
