MCP6031-E/MS - 10kHz Low-Power Rail-to-Rail Op Amp
部品番号: MCP6031-E/MS ✓ 生産中MCP6031-E/MS 概要
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its two inputs. The MCP6031 belongs to the operational-amplifier hierarchy, where low-dropout voltage regulation, high open-loop gain, CMOS construction, and rail-to-rail input and output capability form the basis for accurate signal conditioning. These characteristics allow the device to operate close to the supply rails without requiring a bipolar input stage.
The MCP6031-E/MS provides a typical gain-bandwidth product of 10 kHz and a typical operating current of 900 nA. Its maximum input offset voltage is ±150 µV, while rail-to-rail input and output operation improves usable input range and output swing. These characteristics make it useful for low-frequency filtering, buffering, sensor interfaces, and battery-powered instrumentation where current consumption and offset error are more important than high bandwidth.
Microchip describes the MCP6031 family as using advanced CMOS technology to achieve low bias current, high open-loop gain, high-speed operation, and rail-to-rail input and output swing. A typical slew rate of 0.004 V/µs supports low-frequency closed-loop operation without introducing the switching noise and higher supply current associated with a fast switching-regulator-based signal chain.
Typical applications include photodiode and optical-sensor interfaces, portable measurement systems, low-frequency active filters, sensor-signal conditioning, and precision battery-powered equipment. The manufacturer also identifies the MCP6031 Photodiode PICtail Plus demo board as a transimpedance-amplifier example using an MCP6031 and external resistors to convert photocurrent into voltage.
Design the MCP6031-E/MS for the signal bandwidth rather than its maximum capability. Keep the feedback network and input source impedances appropriate for a 10 kHz amplifier, account for input offset when resolving small sensor outputs, and place the device in a stable low-noise analog layout. The 900 nA operating current supports low-power operation, but external divider, resistor, and leakage currents can dominate the total system current.
This product page combines manufacturer electrical characteristics, package information, application guidance, pin-assignment considerations, and a qualified comparison framework for engineers evaluating low-power precision op amps. It also distinguishes genuine footprint-compatible substitutions from variants that merely share the MCP6031 family name.
ドロップイン代替品: MCP6031-E/MS — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
この製品に利用可能なドロップイン代替品はありません。
代替品をリクエストMCP6031-E/MS 最大定格&電気的特性
| Amplifier Type | Single precision operational amplifier |
| Number of Circuits | 1 circuit |
| Supply Voltage Range | 1.8 V to 5.5 V |
| Typical Operating Current | 900 nA per amplifier |
| Gain-Bandwidth Product | 10 kHz |
| Input Offset Voltage | ±150 µV maximum |
| Slew Rate | 0.004 V/µs |
| Input Common-Mode Range | Rail-to-rail |
| Output Voltage Swing | Rail-to-rail |
| Process Technology | Advanced CMOS |
| Open-Loop Gain | High open-loop gain |
| Input Bias Current | Low bias current |
| パッケージ | 8-pin MSOP |
| 実装タイプ | Surface mount |
| Temperature Grade | Extended temperature grade |
MCP6031-E/MS 8-pin msop ピン配置ガイド
MCP6031-E/MS (8-pin msop パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: MCP6031-E/MS.
詳細は データシート をご参照ください。
主な用途
MCP6031-E/MS の用途: 6 件s: Photodiode Signal Conditioning, Battery-Powered Sensor Interfaces, Low-Frequency Active Filters, Precision Buffering, Portable Measurement Instruments, Industrial Low-Level Signal Conditioning.
Photodiode Signal Conditioning
The MCP6031-E/MS is appropriate for low-frequency photodiode interfaces because its 900 nA typical operating current minimizes system drain, while its ±150 µV maximum input offset voltage limits the effect of amplifier error on small signals. Microchip identifies an MCP6031 transimpedance-amplifier implementation using external resistors to convert photocurrent into voltage. The 10 kHz gain-bandwidth product supports relatively slow optical measurements rather than high-speed optical links. Feedback resistor value and diode capacitance must be selected together to preserve stability and useful bandwidth.
おすすめ
Battery-Powered Sensor Interfaces
A 1.8 V minimum supply and 900 nA typical operating current make the MCP6031-E/MS well suited to battery-operated sensor-conditioning circuits. Rail-to-rail input and output capability preserves signal range in low-voltage systems, and the ±150 µV maximum offset specification helps when conditioning small sensor outputs. The amplifier is appropriate for temperature, pressure, and chemical sensors with slow-changing signals. Because resistor-divider current can exceed the amplifier current, the complete sensor bias network should be calculated before treating 900 nA as the complete standby load.
おすすめ
Low-Frequency Active Filters
The MCP6031-E/MS can implement low-frequency active filters where its 10 kHz gain-bandwidth product provides ample loop gain for modest closed-loop bandwidths. Its 900 nA typical operating current reduces power consumption in portable filter stages, while rail-to-rail outputs increase usable signal amplitude on a 1.8 V to 5.5 V supply. Component tolerances and amplifier offset can shift the filter response. Keep the operating frequency below the bandwidth required for the selected closed-loop gain and verify stability with the final passive-component values.
おすすめ
Precision Buffering
The MCP6031-E/MS can buffer a high-impedance source when the signal bandwidth is below its 10 kHz gain-bandwidth product and source impedance is low enough to avoid excessive differential voltage across the input pair. Rail-to-rail output swing allows the buffered voltage to approach either supply rail, while the 900 nA typical operating current suits compact portable equipment. Input bias current and noise can still create errors with very high source impedances. Choose suitable feedback and bias resistors and confirm offset behavior against the required measurement resolution.
おすすめ
Portable Measurement Instruments
The MCP6031-E/MS supports portable measurement instruments that combine a low-noise analog front end with limited power availability. Its single-supply range begins at 1.8 V, its 900 nA typical current reduces amplifier contribution to standby consumption, and its ±150 µV maximum offset provides a defined error limit for precision measurements. Rail-to-rail operation reduces the need for a negative supply on low-voltage analog inputs. The surrounding sensor interface, reference network, and resistor leakage can dominate system accuracy, so those components should be evaluated together with the amplifier.
おすすめ
Industrial Low-Level Signal Conditioning
The MCP6031-E/MS is suitable for low-level industrial signal-conditioning paths that operate on a 1.8 V to 5.5 V supply and do not require high-frequency amplification. Its maximum input offset voltage of ±150 µV and rail-to-rail input capability support accurate conditioning near the lower supply limit, while the 900 nA typical operating current is advantageous in distributed, low-power measurement systems. Environmental effects, input overvoltage, and resistor-network error require separate protection and review. The amplifier should remain within the manufacturer’s electrical limits even though its low current consumption is favorable.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MCP6031-E/MS — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 |
|---|---|
| Brand | Microchip Technology |
| Package | 8-pin MSOP |
| Amplifier Count | 1 circuit |
| Supply Voltage Range | 1.8 V to 5.5 V |
| Typical Operating Current | 900 nA per amplifier |
| Gain-Bandwidth Product | 10 kHz |
| Input Offset Voltage | ±150 µV maximum |
| Slew Rate | 0.004 V/µs |
| Input and Output Range | Rail-to-rail input and output |
| Technology | Advanced CMOS |
主な差別化要因
- Very low amplifier operating current (vs MCP6031-E/MC)
- Precision offset specification (vs MCP606T-I/ST)
- Single-device rail-to-rail operation (vs MCP6032T-E/SN)
設計ノート
Do not interpret the 10 kHz gain-bandwidth product as the usable closed-loop bandwidth at every gain. The practical bandwidth also depends on the selected noise gain, phase margin, feedback resistance, and source impedance. Use conservative gain for precision filters and buffers, then verify the complete analog network against the intended frequency response. The 900 nA amplifier current does not include current drawn by external dividers, bias networks, or protection devices.
Place the amplifier, feedback components, and input source close together to minimize parasitic capacitance and resistance. Keep sensitive input traces away from digital, switching, and high-current supply paths. Because rail-to-rail input stages can respond to nearby disturbances, use a stable reference or quiet ground plane and avoid routing inputs beneath noisy circuitry. Confirm the package pin assignment in the Microchip Technology data sheet before defining the footprint.
Treat the MCP6031-E/MS as a low-bandwidth precision amplifier rather than a high-speed device. Its 0.004 V/µs slew rate and 10 kHz gain-bandwidth product are adequate for slow sensor signals but can limit large-amplitude outputs at high frequency. Calculate the required output rate as peak voltage multiplied by angular frequency, and select feedback and load values that preserve stability and output swing.
The 1.8 V to 5.5 V single-supply range supports portable operation, but the complete circuit may consume substantially more than the amplifier’s 900 nA typical rating. Sum divider currents, feedback-network currents, sensor bias currents, and leakage paths when estimating standby life. A common-mode input or output that approaches a supply rail should also be checked for saturation margin and the remaining output-swing limitations.
コンプライアンス情報
The manufacturer documentation identifies the MCP6031-E/MS as an extended-temperature operational amplifier. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current product declaration or applicable manufacturer documentation.