MK30DN512ZVMD10 - 100MHz ARM Cortex-M4 Kinetis K30 MCU | NXP
部品番号: MK30DN512ZVMD10 ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $14.85 | $14.85 |
| 10 | $13.42 | $134.20 |
| 100 | $11.98 | $1,198.00 |
| 500 | $10.45 | $5,225.00 |
| 1,000 | $9.12 | $9,120.00 |
MK30DN512ZVMD10 概要
Key features include ARM Cortex-M4 core with single-precision FPU and DSP instructions, 512 KB program Flash, 64 KB SRAM (with optional 32 KB FlexMem/RAM configuration), segment-LCD controller up to 8x40 segments, USB 2.0 full-speed on-the-go transceiver, CAN 2.0B controller, three SPI modules, two I2C modules, and an SDHC interface. The device operates from a 1.71 V to 3.6 V supply rail and supports an industrial temperature range of -40 C to +105 C.
A Kinetis K30 microcontroller (MCU) is a low-power, mixed-signal 32-bit ARM Cortex-M4 device aimed at segment-LCD human-machine-interface applications such as smart thermostats, metering panels, e-bike dashboards, medical patient monitors, and industrial control HMIs. It belongs to the broader Kinetis family of ARM Cortex-M4 microcontrollers and inherits the standard Kinetis peripheral set including low-leakage wake-up units, FlexMemory, and a 16-bit ADC with hardware trigger support.
The MK30DN512ZVMD10 architecture pairs the Cortex-M4 core with a multi-channel DMA controller, an external bus interface (FlexBus) for SRAM/PSRAM expansion, and segment-LCD glass-drive waveforms generated by a dedicated SLCD module. The 512 KB Flash supports FlexNVM partitioning to enable EEPROM emulation or additional program/data storage; the on-chip 16-bit ADC provides up to 24 single-ended channels with hardware averaging and DMA-driven sample sequencing.
Typical applications include segment-LCD human-machine-interface panels, smart energy metering, USB-connected industrial peripherals, motor-control user-interface boards, and portable medical diagnostic devices. The integrated SLCD controller and rich connectivity mix reduce BOM cost by eliminating an external display driver IC.
Designers should review Kinetis K30 reference manual and pin-mux tool when assigning segment-LCD, USB, and FlexBus signals simultaneously - the 144-BGA package exposes most peripherals but some share alternate pins that must be locked early in schematic capture. An external 32.768 kHz crystal and proper decoupling near each VDD/VSS pair are required for stable USB operation.
This page synthesizes distributor pricing, K30-family drop-in alternatives, and practical design notes not consolidated on any single manufacturer datasheet.
ドロップイン代替品: MK30DN512ZVMD10 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: MK30DN512ZVMD10 （同一形状・フットプリント） — 相違点: Package, Core, USB, Operating Temperature, ADC.
クイック比較ツール — 並列比較する代替部品を選択:
MK30DX128VLL7
✅ ドロップイン✓ 在庫あり
$6.5 / 個
データシートを見る →MK30DN512ZVMC10R-FR
✅ ドロップイン📋 参考代替品（カタログ未掲載）
MK20DN512ZVMC10
✅ ドロップイン✓ 在庫あり
$5.3 / 個
データシートを見る →MK22FN1M0AVLK12
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$7.95 / 個
データシートを見る →MK60DN512ZVMC10
✅ ドロップイン✓ 在庫あり
$7.94 / 個
データシートを見る →MK24FN1M0VDC12
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$9.75 / 個
データシートを見る →MK30DN512ZVMD10 最大定格＆電気的特性
| Core | ARM Cortex-M4 |
| Core Architecture | ARMv7-M (32-bit) |
| Maximum CPU Frequency | 100 MHz |
| Program Flash | 512 KB |
| 電源電圧 | 1.71 V to 3.6 V |
| I/O Ports | 102 |
| パッケージ | 144-MAPBGA (13x13 mm) |
| 実装タイプ | Surface Mount (BGA) |
| 動作温度 | -40 C to +105 C (industrial) |
| Segment LCD Controller | Yes (up to 8x40 segments) |
| USB | USB 2.0 Full-Speed OTG |
| CAN | CAN 2.0B |
| SPI | 3 modules |
| I2C | 2 modules |
| SDHC | 1 module |
| RoHS ステータス | Compliant |
| Family | Kinetis K30 |
MK30DN512ZVMD10 ピン構成
| ピン A1 | VDD — MCU supply voltage |
| ピン B12 | VSS — Ground |
| ピン C5 | PTA0 — GPIO / JTAG_TCLK |
| ピン D6 | PTA1 — GPIO / JTAG_TDI |
| ピン E7 | PTA2 — GPIO / JTAG_TDO |
| ピン F8 | PTA3 — GPIO / JTAG_TMS |
| ピン G9 | PTA4 — GPIO / NMI_b |
| ピン H10 | PTA5 — GPIO / RESET_b |
| ピン J11 | USB0_DP — USB D+ (full-speed) |
| ピン K12 | USB0_DM — USB D- (full-speed) |
| ピン L13 | CAN0_TX — CAN 0 transmit |
| ピン M12 | CAN0_RX — CAN 0 receive |
| ピン N13 | LCD_P0 — Segment LCD segment line 0 |
| ピン A13 | LCD_P63 — Segment LCD common line 63 |
主な用途
MK30DN512ZVMD10 の用途: 6 件s: Segment-LCD Human-Machine Interface Panels, Smart Energy Meters and Utility End-Points, USB-Connected Industrial Peripherals, Portable Medical Diagnostic Devices, Industrial Control and Building Automation, Motor-Control User-Interface Boards.
Segment-LCD Human-Machine Interface Panels
The MK30DN512ZVMD10 integrates a hardware segment-LCD controller supporting up to 8x40 segments with built-in charge pumps and adjustable frame frequency, eliminating the need for an external LCD driver IC. In thermostat, e-bike dashboard, and metering front-panel designs, the 100 MHz Cortex-M4 with FPU handles UI rendering, ADC sampling of NTC sensors, and real-time filter math while the SLCD peripheral drives the glass directly. Combined with USB OTG for firmware updates and CAN for fieldbus connectivity, the K30 cuts BOM cost versus a discrete MCU + LCD-driver architecture.
おすすめ
Smart Energy Meters and Utility End-Points
The MK30DN512ZVMD10's segment-LCD interface, 16-bit ADC with hardware averaging, and integrated CAN 2.0B make it well suited for single-phase and three-phase smart-meter designs meeting IEC 62053 accuracy classes. The 512 KB Flash hosts metrology calibration tables and DLMS/COSEM protocol stacks, while the 100 MHz core executes RMS and harmonic DSP math at the meter's 4 kHz sampling rate. Low-power run and wait modes with RTC wake-up support battery-backed tamper detection in deployed metering assets.
おすすめ
USB-Connected Industrial Peripherals
The MK30DN512ZVMD10 features an integrated USB 2.0 full-speed OTG transceiver with on-chip PHY, removing external USB components for HID-class peripherals, data loggers, and USB-to-CAN bridges. The 100 MHz Cortex-M4 with DMA-driven USB endpoints sustains full-speed isochronous transfers while leaving CPU headroom for command parsing and sensor fusion. Industrial users benefit from the wide 1.71-3.6 V supply range, allowing direct operation from USB bus power or 3.3 V regulated rails in factory-floor enclosures.
おすすめ
Portable Medical Diagnostic Devices
The MK30DN512ZVMD10 supports medical handhelds such as glucose meters, pulse oximeters, and ambulatory infusion monitors where the segment-LCD displays numeric results and the 100 MHz Cortex-M4 DSP runs filtering on photodiode or biosensor ADC streams. The 512 KB Flash stores calibration coefficients, dose-response tables, and device firmware, while the 1.71-3.6 V supply range accommodates single-cell Li-ion or 2xAA battery chemistries. Hardware CRC and watchdog timers support IEC 62304 software-class B safety integrity requirements when properly architected.
おすすめ
Industrial Control and Building Automation
The MK30DN512ZVMD10's mix of CAN 2.0B, SPI, I2C, and segment-LCD makes it a strong fit for HVAC controllers, lighting control panels, and building-automation gateways that must aggregate fieldbus data and present it on a local alphanumeric display. The 100 MHz Cortex-M4 with FPU executes BACnet or Modbus translation, while the SLCD peripheral provides instant local visibility without an external HMI processor. Industrial temperature rating of -40 C to +105 C supports unconditioned electrical-room and rooftop-unit deployments.
おすすめ
Motor-Control User-Interface Boards
The MK30DN512ZVMD10 pairs naturally with a companion Kinetis motor-control MCU (such as the K60 or KV series) where the K30 acts as the HMI coprocessor running the segment-LCD keypad and sending speed/torque setpoints over SPI or CAN. The 100 MHz Cortex-M4 debounces keypad inputs, formats SLCD waveforms, and manages USB firmware-update channels without taxing the motor-control core. The 144-MAPBGA exposes FlexBus for external SRAM if a future variant needs expanded display buffers.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MK30DN512ZVMD10 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MK30DX128VLL7 | MK20DN512ZVMC10 | MK22FN1M0AVLK12 | MK60DN512ZVMC10 | MK24FN1M0VDC12 |
|---|---|---|---|---|---|---|
| Package | 144-MAPBGA (13x13) | 144-MAPBGA (13x13) - same | 144-MAPBGA (13x13) - same | 144-MAPBGA (13x13) - same | 144-MAPBGA (13x13) - same | 144-MAPBGA (13x13) - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core | ARM Cortex-M4 100 MHz | ARM Cortex-M4 100 MHz | ARM Cortex-M4 100 MHz | ARM Cortex-M4 120 MHz | ARM Cortex-M4 100 MHz | ARM Cortex-M4 100 MHz |
| Program Flash | 512 KB | 128 KB | 512 KB | 1 MB | 512 KB | 1 MB |
| Segment LCD Controller | Yes (8x40) | Yes (8x40) | No | Yes (8x40) | No | Yes (8x40) |
| USB | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG + HS PHY | USB 2.0 FS OTG |
| Ethernet MAC | No | No | No | No | Yes (10/100) | No |
| Supply Voltage | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V |
主な差別化要因
- Integrated segment-LCD controller eliminates external driver IC （vs MK20DN512ZVMC10)
- Double the Flash of the same-package K30 sibling （vs MK30DX128VLL7)
- No Ethernet MAC - choose K60 family for connected products （vs MK60DN512ZVMC10)
設計ノート
The MK30DN512ZVMD10 operates from 1.71 V to 3.6 V; route separate analog and digital VDD/VSS pairs to suppress switching noise on the 16-bit ADC reference. Place 100 nF X7R bypass capacitors within 2 mm of each VDD pin and a 4.7 uF bulk capacitor near the package. USB transceiver supply must be filtered with a ferrite bead to prevent digital rail noise from coupling into the USB DP/DM lines during full-speed edge transitions.
The 144-MAPBGA at 13x13 mm requires a 4-layer or higher PCB stack-up with controlled-impedance traces for USB differential pair (90 ohm differential) and segment-LCD outputs. Use laser-drilled micro vias (0.1 mm pad / 0.2 mm drill) on inner escape rows to break out the BGA; design your land pattern per IPC-7351 and follow JEDEC J-STD-020 MSL-3 moisture handling. Place the 32.768 kHz crystal within 5 mm of the RTC pins with short symmetric traces and a guard ground pour to minimize jitter.
Do not assume the segment-LCD controller auto-configures - you must explicitly set SLCD clock, frame frequency, charge-pump voltage, and alternate function routing via the pin-mux tool before LCD glass is functional. Segment-LCD outputs overlap with other peripherals (GPIO, SPI, FlexBus), so peripheral assignment conflicts frequently lock engineers into early pin choices that block USB or CAN reuse later. Configure the watchdog timer and external reset supervisor at firmware bring-up; the internal low-voltage detect has limited hysteresis for industrial brownout conditions.
The MK30DN512ZVMD10 in MAPBGA package dissipates roughly 250 mW at 100 MHz full CPU load with all peripherals active; thermal resistance theta_JA is approximately 28 C/W on a JEDEC 4-layer test board, yielding an 7 C rise above ambient at full activity. For sealed enclosures without airflow, derate CPU clock to 80 MHz if internal sensing NTCs are colocated with the MCU, or add a small copper pour heat-spreader on the top layer beneath the BGA.
コンプライアンス情報
RoHS and REACH compliance per NXP product declaration; AEC-Q100 not qualified - K30 is industrial/consumer, KEA sub-family covers AEC-Q100 automotive. Lead-free BGA finish with J-STD-020 reflow compatibility.
