MPC8533EVTALFA557 - PowerQUICC III 667MHz SoC | NXP Semiconductors
部品番号: MPC8533EVTALFA557 ✓ 生産中MPC8533EVTALFA557 概要
A PowerQUICC integrated communications processor is a category of embedded SoC that combines a high-performance CPU core with multiple communications peripherals on a single die, typically used for networking and telecom equipment where deterministic throughput and protocol acceleration are critical. The MPC8533E belongs to the PowerPC e500 family of reduced-instruction-set processors, descendants of the original Power Architecture used in early Apple-IBM-Motorola workstations. In the broader taxonomy, it is a microprocessor -> embedded processor -> communications SoC -> networking ASIC, occupying a tier just below full network processors but above general-purpose MCUs.
Key features include hardware-accelerated cryptography (SEC engine), integrated DDR1/DDR2 controller with ECC support, dual Gigabit Ethernet MACs, PCI Express and PCI interfaces, USB 2.0 controller, four DMA channels, and dual I²C. The 32-bit Power Architecture v2 core runs at 667 MHz with a 32 KB L1 instruction cache, 32 KB L1 data cache, and a 256 KB unified L2 cache. The 783-FCPBGA package offers high signal density required to route the multiple parallel buses, SerDes lanes, and memory channels.
Architecturally, the MPC8533E combines a single e500v2 core with the QUICC Engine technology block for protocol handling, offloading tasks such as ATM, Ethernet, and HDLC from the CPU. Silicon revision 2.1 includes errata fixes accumulated since the original mask set, and the extended temperature grade (0°C to 90°C) targets commercial and industrial networking deployments rather than full automotive-grade AEC-Q100 applications.
Typical applications include wired networking routers and switches, industrial control gateways, telecom base-station control boards, network-attached storage (NAS) controllers, and embedded telecommunications platforms. The integrated security engine makes the MPC8533E particularly suited for VPN gateways, secure routers, and IPsec/SSL acceleration appliances. The dual Gigabit Ethernet and PCI Express connectivity suit it for line-card processors in modular chassis designs.
When designing with this device, allocate a minimum 4-layer PCB with dedicated ground planes under the BGA to maintain signal integrity on the DDR2 memory bus. The 783-ball FCPBGA requires 0.8 mm or 1.0 mm pitch land patterns and reflow profiles compliant with JEDEC J-STD-020. Plan for thermal dissipation of 6-9 W typical; the package's theta-JA of approximately 18 °C/W requires thermal vias and bottom-side copper pours for reliable operation at full 667 MHz clock.
This page synthesizes distributor inventory snapshots, lifecycle context, drop-in compatibility data, and engineering design considerations that are not collated in the manufacturer hardware-specifications document alone.
ドロップイン代替品: MPC8533EVTALFA557 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
MPC8533EVTALFA
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
MPC8533EVTANFA
✅ ドロップイン📋 参考代替品（カタログ未掲載）
MPC8533EVTARFA
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
MPC8533EVTANGFA557
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
MPC8533EVTALFA
✅ ドロップイン📋 参考代替品（カタログ未掲載）
MPC8533EVTALFA557 最大定格＆電気的特性
| Architecture | PowerPC e500v2 |
| Core Count | 1 |
| データバス幅 | 32-bit |
| 最大クロック周波数 | 667 MHz |
| パッケージ | 783-FCPBGA (29x29 mm) |
| Memory Controller | DDR1 / DDR2 with ECC |
| L1 Instruction Cache | 32 KB |
| L1 Data Cache | 32 KB |
| L2 Cache | 256 KB unified |
| Ethernet | Dual Gigabit Ethernet MACs |
| PCI / PCIe Interfaces | PCI and PCI Express |
| USB | USB 2.0 |
| Security Engine | SEC (IPsec/SSL acceleration) |
| DMA Channels | 4 |
| I²C Controllers | 2 |
| 動作温度 | 0°C to 90°C |
| Silicon Revision | Rev 2.1 |
| 実装タイプ | Surface Mount (BGA) |
| RoHS ステータス | Compliant |
MPC8533EVTALFA557 783-fcpbga (29x29 mm) ピン配置ガイド
MPC8533EVTALFA557 (783-fcpbga (29x29 mm) パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: MPC8533EVTALFA557.
詳細は データシート をご参照ください。
主な用途
MPC8533EVTALFA557 の用途: 6 件s: Wired Enterprise Router / VPN Gateway, Network-Attached Storage (NAS) Controller, Telecom Base Station Control Board, Industrial Control Gateway, Secure Router for SOHO / SMB, Embedded Telecommunications Platform.
Wired Enterprise Router / VPN Gateway
The MPC8533EVTALFA557 fits wired enterprise router and VPN gateway designs where its integrated Security Engine (SEC) accelerates IPsec and SSL/TLS at line rate while the PowerPC e500v2 core at 667 MHz handles routing tables and control-plane protocols. Dual Gigabit Ethernet MACs feed packets through QUICC Engine protocol offload, and the DDR2 controller with ECC provides robust memory throughput for routing lookups and crypto key tables. Placing the MPC8533E as the main SoC reduces BOM count versus discrete CPU-plus-NPU architectures, while PCIe connectivity allows expansion to multi-Gigabit or 10G uplinks via external PHY/MAC cards.
おすすめ
Network-Attached Storage (NAS) Controller
The MPC8533EVTALFA557 suits small-to-medium NAS controllers where its Gigabit Ethernet and SATA-capable PCI/PCIe interfaces connect to disk arrays while the e500v2 core runs NAS firmware, file-system stacks, and user authentication. The 256 KB L2 cache accelerates directory traversal and the SEC engine accelerates SMB / NFS Kerberos authentication. The 667 MHz clock is sufficient for sustained 100 MB/s file-transfer throughput with multiple concurrent clients, and the 783-FCPBGA's high signal density simplifies the multi-SATA design with reduced routing congestion.
おすすめ
Telecom Base Station Control Board
The MPC8533EVTALFA557 fits telecom base-station control boards where deterministic latency, hardware cryptography, and a wide peripheral set replace multiple discrete MCUs. The e500v2 core executes real-time control loops while the SEC engine secures backhaul links via IPsec; the QUICC Engine block handles TDM / E1 / T1 framing for legacy telecom I/O. The DDR2 controller with ECC supports the memory bandwidth needed for Layer-2 / Layer-3 protocol processing, and PCI Express interfaces connect to baseband FPGA co-processors or DSP arrays for radio-chain processing.
おすすめ
Industrial Control Gateway
The MPC8533EVTALFA557 suits industrial control gateways where its combination of Ethernet, USB, and PCI connectivity bridges factory-floor protocols (Modbus, Profinet, EtherNet/IP) to enterprise IT networks. The e500v2 core runs gateway logic while the SEC engine secures remote-management sessions via SSL/TLS. Dual I²C controllers interface to local sensors and supervisory ICs, and the integrated DMA engine moves bulk sensor data without CPU intervention. The 783-FCPBGA package's commercial 0-90°C window suits climate-controlled control cabinets; for outdoor or unheated enclosures, select the industrial-temperature variant instead.
おすすめ
Secure Router for SOHO / SMB
The MPC8533EVTALFA557's SEC-accelerated IPsec makes it ideal for SOHO / SMB secure router designs where it can sustain line-rate VPN throughput on both Gigabit Ethernet ports while running the routing stack on the e500v2 core. The USB 2.0 interface supports 3G/4G dongles for cellular failover or external storage, and the PCI/PCIe expansion bus allows Wi-Fi 6 / 802.11ax modules for wireless backhaul. The 667 MHz clock is more than sufficient for 1 Gbps routing, and the 783-FCPBGA's compact footprint simplifies the small-form-factor chassis layout typical of SOHO appliances.
おすすめ
Embedded Telecommunications Platform
The MPC8533EVTALFA557 fits embedded telecom platforms including IP-PBX controllers, media gateways, and unified-communications appliances. Its QUICC Engine handles multi-channel TDM voice while the SEC engine secures SIP/TLS signalling. The DDR2 controller with ECC provides the memory bandwidth for packet-voice processing, and the PCI/PCIe lanes connect to DSP arrays for echo-cancellation and voice-quality enhancement. The e500v2 core runs VxWorks or embedded Linux for deterministic telecom-software stacks, and the 783-FCPBGA's commercial 0-90°C window suits the climate-controlled telecom-room environment.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MPC8533EVTALFA557 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MPC8533EVTALFA | MPC8533EVTANFA | MPC8533EVTARFA | MPC8533EVTANGFA557 |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 783-FCPBGA (29x29) | 783-FCPBGA (29x29) - same | 783-FCPBGA (29x29) - same | 783-FCPBGA (29x29) - same | 783-FCPBGA (29x29) - same |
| Core Architecture | PowerPC e500v2 | PowerPC e500v2 | PowerPC e500v2 | PowerPC e500v2 | PowerPC e500v2 |
| Clock Frequency | 667 MHz | 667 MHz | 667 MHz | 667 MHz | 667 MHz |
| Operating Temperature | 0°C to 90°C | 0°C to 90°C | -40°C to 105°C | 0°C to 90°C | -40°C to 105°C |
| Security Engine (SEC) | Yes | Yes | Yes | Yes | Yes |
| Memory Controller | DDR1/DDR2 with ECC | DDR1/DDR2 with ECC | DDR1/DDR2 with ECC | DDR1/DDR2 with ECC | DDR1/DDR2 with ECC |
主な差別化要因
- Higher commercial operating temperature ceiling vs industrial variants （vs MPC8533EVTANFA)
- Integrated Security Engine (SEC) for line-rate crypto （vs MPC8533 (non-E variant))
- Mature PowerPC e500v2 ecosystem with extensive BSP support （vs Newer QorIQ P1010)
設計ノート
The 783-FCPBGA package requires a minimum 4-layer PCB stack-up to maintain controlled impedance on the DDR2 memory bus (typically 50 ohm single-ended, 100 ohm differential for PCIe). Use 1 oz copper on outer layers and 0.5 oz on inner layers, with dedicated ground planes directly under the BGA. Per JEDEC J-STD-020, the FCPBGA requires MSL-3 handling and a peak reflow temperature of 245°C for lead-free assembly.
Estimated: typical power dissipation of the MPC8533EVTALFA557 at 667 MHz with active Ethernet and SEC engines is approximately 6-9 W. The 783-FCPBGA package's theta-JA of approximately 18 °C/W (with thermal vias and 4-layer PCB copper pours) means junction temperature rise above ambient is 108-162°C, which exceeds the 90°C commercial limit. Provide thermal vias under the package's thermal balls, bottom-side copper flood, and adequate airflow. For sealed enclosures, select the industrial-temperature variant MPC8533EVTANFA instead.
Do not assume all MPC8533 family members share identical silicon revisions - the trailing letter in the part number (e.g., 'A' in VTALFA vs 'R' in VTARFA) encodes silicon revision and packaging. Verify the silicon revision matches your firmware's errata list before substituting. The 'E' suffix indicates the integrated Security Engine - parts without 'E' (plain MPC8533) lack SEC and cannot run IPsec/SSL acceleration.
コンプライアンス情報
RoHS compliance per NXP product page. Not AEC-Q100 qualified - choose industrial or automotive variants if AEC-Q100 is required.