OPA686U - Wideband Low-Noise Voltage-Feedback Op Amp | TI
部品番号: OPA686U ✗ 生産終了| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $0 | $0.00 |
| 10 | $0 | $0.00 |
| 100 | $0 | $0.00 |
| 500 | $0 | $0.00 |
| 1,000 | $0 | $0.00 |
OPA686U 概要
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its input terminals while using negative feedback to set closed-loop gain and bandwidth. The voltage-feedback topology is widely used in signal-conditioning, measurement, communications, and audio circuits because its response can be shaped with external resistors and capacitors. OPA686U belongs to the SpeedPlus family identified in the verified datasheet search results, emphasizing wideband performance and low noise for high-frequency analog signal paths.
The key verified feature set is single-circuit integration, voltage-feedback architecture, 8-SOIC packaging, wideband response, and 1.3 nV/√Hz input voltage-noise density. These attributes make the OPA686U relevant to low-level signal amplification, instrumentation front ends, communication receivers, test and measurement equipment, and analog signal-processing circuits. The SOIC-8 package also supports conventional surface-mount assembly, although exact pin functions, exposed-pad details, and mechanical dimensions require confirmation from the manufacturer datasheet.
OPA686U should be selected by evaluating the complete operating condition set rather than bandwidth or noise alone. Supply rails, input and output swing, gain configuration, stability, noise at the signal bandwidth, and the required output load must be verified against the manufacturer datasheet before layout or production release. Wideband feedback layouts should minimize parasitic capacitance and use short, direct traces.
Typical uses include receiver and transceiver signal conditioning, low-level sensor amplification, waveform shaping, communications filtering, laboratory instrumentation, and audio or video analog stages. In these applications, the 1.3 nV/√Hz input-voltage-noise figure can help determine whether the amplifier’s noise contribution is acceptable relative to the source impedance and system bandwidth.
The principal design consideration is bandwidth-driven layout discipline. Keep the feedback network close to the amplifier pins, preserve the intended ground return path, and validate stability with the actual source and load impedances. Do not substitute a mechanically similar amplifier solely because it uses an 8-pin SOIC package; verify pinout, supply range, noise, gain-bandwidth product, and distortion requirements first.
This product record combines the verified distributor and manufacturer-search information, the supplied datasheet references, practical signal-integrity guidance, and explicit data gaps. Because the verified excerpts do not provide a complete electrical table or confirmed pricing schedule, the structured record avoids inventing those values and identifies unavailable parameters directly.
ドロップイン代替品: OPA686U — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
クイック比較ツール — 並列比較する代替部品を選択:
OPA686UA
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
OPA686UB
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
OPA686UC
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
OPA686UID
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
OPA686UIR
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
OPA686U 最大定格＆電気的特性
| Amplifier Type | Voltage Feedback Operational Amplifier |
| Number of Circuits | 1 |
| Input Voltage Noise Density | 1.3 nV/√Hz |
| Bandwidth Class | Wideband |
| Architecture | Voltage Feedback |
| Product Family | SpeedPlus |
| パッケージ | 8-SOIC |
| Package Type | Small-outline integrated circuit |
| 実装タイプ | Surface Mount |
| Supplier Description | Instrumentation, op amps, buffer amplifiers |
| ピン数 | 8 pins |
OPA686U small-outline integrated circuit ピン配置ガイド
OPA686U (small-outline integrated circuit パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: OPA686U.
詳細は データシート をご参照ください。
主な用途
OPA686U の用途: 6 件s: Communications Signal Conditioning, Instrumentation and Sensor Front Ends, Test and Measurement Signal Paths, Audio and Video Analog Amplification, RF and Microwave-Control Interfaces, Industrial Control and Data Acquisition.
Communications Signal Conditioning
OPA686U fits a communications front end when the design needs a wideband voltage-feedback amplifier with low input voltage noise. Its verified 1.3 nV/√Hz input-noise density helps limit amplifier-added noise in receiver and transceiver signal paths, while the wideband description supports higher-frequency conditioning than a conventional general-purpose amplifier. Place the device where source, feedback, and output traces remain short, and confirm supply range, input common-mode range, output swing, and stability from the manufacturer datasheet. The amplifier should be selected only after confirming that its distortion and dynamic-range ratings meet the channel requirement.
おすすめ
Instrumentation and Sensor Front Ends
OPA686U can be evaluated for low-level instrumentation because the verified distributor classification includes instrumentation amplifiers and the device has a specified 1.3 nV/√Hz input voltage-noise density. The voltage-feedback architecture allows the engineer to set gain and bandwidth with external feedback components when the manufacturer stability and noise conditions permit. Use short sensor traces, guard or isolation techniques where appropriate, and verify input bias current, offset voltage, common-mode range, and output drive against the sensor source. The complete electrical table is not included in the supplied data, so the final sensor design requires the current manufacturer datasheet.
おすすめ
Test and Measurement Signal Paths
OPA686U is relevant to wideband test and measurement circuits where a low-noise voltage-feedback stage can condition an input before a converter, attenuator, or comparator. The verified 1.3 nV/√Hz noise figure is a useful starting point for noise budgeting, but the total integrated input noise depends on the selected bandwidth and temperature. Keep the feedback loop compact and use controlled grounding to prevent measurement errors from board leakage and coupling. Before using the amplifier with laboratory gain ranges or precision DC measurements, verify offset, bias current, input range, and output linearity from the manufacturer datasheet.
おすすめ
Audio and Video Analog Amplification
OPA686U may be considered for audio or video analog stages when the circuit benefits from wideband response and low input voltage noise. The verified product description identifies a wideband, low-noise voltage-feedback amplifier, but it does not establish headphone output-current capability, THD figures, or output-swing limits. Those omissions are important for direct-drive loads and line-level video circuits. Use the amplifier primarily for low-level intermediate stages unless the complete datasheet confirms the required load, bandwidth, distortion, and supply conditions. A local feedback and grounding layout is especially important in mixed audio/video systems.
おすすめ
RF and Microwave-Control Interfaces
OPA686U can be evaluated as a low-noise analog interface around RF control or measurement circuitry when the signal bandwidth and frequency response are compatible. Its verified wideband voltage-feedback description may help preserve fast control-signal dynamics, while the 1.3 nV/√Hz input-noise specification supports noise-sensitive amplifier stages. The supplied data does not verify RF-specific gain, isolation, phase-noise, or impedance parameters, so the component should not be assumed suitable for every RF frequency. Confirm the complete datasheet, package parasitics, and PCB environment before placing it beside sensitive RF nodes.
おすすめ
Industrial Control and Data Acquisition
OPA686U may suit industrial control and data-acquisition modules when the analog signal path needs low noise and a wideband voltage-feedback response. It can amplify a conditioned sensor or transducer signal before an ADC, provided the source impedance, common-mode voltage, output swing, and required settling behavior are compatible. The verified 1.3 nV/√Hz input-noise density helps establish the amplifier-noise contribution in the design calculation. Industrial systems should also address supply regulation, surge protection, temperature range, isolation, and grounding; these requirements cannot be validated from the supplied excerpts alone.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: OPA686U — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | OPA686UA | OPA686UB | OPA686UC | OPA686UID | OPA686UIR |
|---|---|---|---|---|---|---|
| Package | 8-SOIC | 8-SOIC - same package, exact pinout requires verification | 8-SOIC - same package, exact pinout requires verification | 8-SOIC - same package, exact pinout requires verification | 8-SOIC - same package, exact pinout requires verification | 8-SOIC - same package, exact pinout requires verification |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
主な差別化要因
- Verified low-noise input characteristic （vs OPA686UA)
- Wideband voltage-feedback positioning （vs OPA686UB)
- Single-circuit 8-SOIC implementation （vs OPA686UC)
設計ノート
Keep the OPA686U feedback loop physically short and place feedback resistors close to the amplifier pins. Because the verified product data identifies a wideband voltage-feedback amplifier, longer loops and excessive parasitic capacitance can reduce stability or alter the intended frequency response. Use a continuous ground reference and route high-frequency output away from sensitive input and reference nodes. The supplied excerpts do not provide a complete pin-level layout, so use the manufacturer recommended layout as the controlling reference.
Treat the input and feedback nets as high-impedance signal paths. Minimize leakage and capacitive coupling from adjacent clock, switching, and power nodes, and maintain a practical ground return for both input and output currents. The verified input voltage-noise density is 1.3 nV/√Hz, but the actual system noise also depends on source impedance, temperature, bandwidth, resistor noise, and PCB contamination. Do not infer total noise from the noise-density figure alone.
Do not select a substitute solely because it is an 8-SOIC amplifier. Confirm the exact pinout, supply voltage range, input common-mode range, output swing, gain-bandwidth product, noise, distortion, stability, and load capability against the OPA686U manufacturer datasheet. The verified cross-reference search did not identify a confirmed drop-in replacement, so any equivalent must be qualified experimentally and against the complete electrical specification before production release.
コンプライアンス情報
Compliance information was not included in the verified excerpts. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status using the current manufacturer product documentation and applicable supply-chain declarations.
