PIC16C64A-20E/PT - 8-Bit 20MHz OTP MCU 3.5KB | Microchip
部品番号: PIC16C64A-20E/PT ✗ 生産終了| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $18.75 | $18.75 |
| 10 | $17.1 | $171.00 |
| 100 | $15.2 | $1,520.00 |
| 500 | $13.65 | $6,825.00 |
| 1,000 | $12.4 | $12,400.00 |
PIC16C64A-20E/PT 概要
An 8-bit OTP microcontroller is a single-chip computer built around an 8-bit data path and Harvard architecture, executing one instruction per instruction cycle (four clock cycles). Within the broader product hierarchy, the PIC16C64A belongs to the PIC16C family -> PIC16 mid-range microcontrollers -> 8-bit MCUs -> microcontrollers -> microprocessors and logic devices -> semiconductors. One-Time Programmable memory means the device is programmed once and cannot be erased, which makes this part well suited for high-volume, cost-sensitive, fully matured production runs where firmware is final. The PIC16C64A is now considered a legacy/obsolete device in the Microchip portfolio.
Key features include 33 general-purpose digital I/O pins, an integrated USART for asynchronous and synchronous serial communication, a Synchronous Serial Port (SSP) supporting both SPI and I²C master/slave modes, three hardware timers (Timer0, Timer1, Timer2), an 8-bit ADC with 8 input channels (on 'A' revision parts), and a capture/compare/PWM (CCP) module. Brown-out Reset and a watchdog timer with its own on-chip RC oscillator provide system-level robustness. The device operates from 2.5 V to 6.0 V and is fabricated on a low-power CMOS process.
Typical applications include industrial control systems, automotive body electronics, white goods and appliance control, instrumentation, and any cost-sensitive embedded design that has transitioned out of the prototyping phase and into stable volume production. The wide temperature range supports both outdoor and under-hood deployments, while the integrated peripherals eliminate external UART and SPI bridges.
When migrating from OTP to flash memory, designers should evaluate the PIC16F77 or PIC16F877A as flash-based equivalents. The PT suffix indicates lead-free matte-tin TQFP termination suitable for modern reflow profiles. This page synthesizes distributor pricing, drop-in TQFP-44 alternatives, and practical design notes not found in the standalone Microchip datasheet.
ドロップイン代替品: PIC16C64A-20E/PT — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: PIC16C64A-20E/PT （同一形状・フットプリント） — 相違点: RoHS Status, Operating Temperature Range, Package, Instruction Cycle Time, ADC.
クイック比較ツール — 並列比較する代替部品を選択:
PIC16C64A-10I/PT
✅ ドロップイン✓ 在庫あり
$5.85 / 個
データシートを見る →PIC16C64A-04I/PT
✅ ドロップイン✓ 在庫あり
$4.61 / 個
データシートを見る →PIC16C64A-04E/PT
✅ ドロップイン✓ 在庫あり
$7.35 / 個
データシートを見る →PIC16C65B-20E/PT
✅ ドロップイン📋 参考代替品（カタログ未掲載）
PIC16F74-I/PT
✅ ドロップイン✓ 在庫あり
$5.55 / 個
データシートを見る →PIC16C64A-20E/PT 最大定格＆電気的特性
| Core Architecture | 8-bit PIC (Harvard) |
| Family | PIC16C mid-range |
| Program Memory Type | One-Time Programmable (OTP) EPROM |
| Program Memory Size | 3.5 KB (2K x 14) |
| RAM | 128 bytes |
| EEPROM Data Memory | 0 bytes (none on this part) |
| Maximum CPU Frequency | 20 MHz |
| Instruction Set | 35 instructions, 14-bit word |
| I/O Pins | 33 |
| Operating Voltage | 2.5 V to 6.0 V |
| 動作温度 | -40 °C to +125 °C (extended 'E' grade) |
| パッケージ | TQFP-44 (PT), 10 x 10 mm |
| 実装タイプ | Surface Mount |
| ADC | 8-bit, 8 channels |
| Timers | 3 (Timer0, Timer1, Timer2) |
| Serial Interfaces | USART, SSP (SPI / I²C) |
| CCP Modules | 1 (capture / compare / PWM) |
| RoHS ステータス | Compliant (lead-free matte-tin finish) |
PIC16C64A-20E/PT ピン構成
| ピン 1 | MCLR/VPP — Master clear reset input / programming voltage |
| ピン 2 | RA0/AN0 — PORTA bit 0 / analog input 0 |
| ピン 3 | RA1/AN1 — PORTA bit 1 / analog input 1 |
| ピン 4 | RA2/AN2 — PORTA bit 2 / analog input 2 |
| ピン 5 | RA3/AN3/VREF — PORTA bit 3 / analog input 3 / ADC reference |
| ピン 6 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| ピン 7 | RA5/AN4/SS — PORTA bit 5 / analog input 4 / SPI slave select |
| ピン 8 | RE0/RD/AN5 — PORTE bit 0 / read control / analog input 5 |
| ピン 9 | RE1/WR/AN6 — PORTE bit 1 / write control / analog input 6 |
| ピン 10 | RE2/CS/AN7 — PORTE bit 2 / chip select / analog input 7 |
| ピン 11 | VDD — Positive supply (2.5 V to 6.0 V) |
| ピン 12 | VSS — Ground reference |
| ピン 13 | OSC1/CLKIN — Oscillator input / external clock in |
| ピン 14 | OSC2/CLKOUT — Oscillator output / clock out |
| ピン 15 | RC0/T1OSO/T1CKI — PORTC bit 0 / Timer1 oscillator output / clock input |
| ピン 16 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator input / CCP2 |
| ピン 17 | RC2/CCP1 — PORTC bit 2 / capture compare PWM 1 |
| ピン 18 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I²C clock |
| ピン 19 | RD0 — PORTD bit 0 |
| ピン 20 | RD1 — PORTD bit 1 |
| ピン 21 | RD2 — PORTD bit 2 |
| ピン 22 | RD3 — PORTD bit 3 |
| ピン 23 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I²C data |
| ピン 24 | RC5/SDO — PORTC bit 5 / SPI data out |
| ピン 25 | RC6/TX/CK — PORTC bit 6 / USART transmit / clock |
| ピン 26 | RC7/RX/DT — PORTC bit 7 / USART receive / data |
| ピン 27 | RD4 — PORTD bit 4 |
| ピン 28 | RD5 — PORTD bit 5 |
| ピン 29 | RD6 — PORTD bit 6 |
| ピン 30 | RD7 — PORTD bit 7 |
| ピン 31 | VSS — Ground reference |
| ピン 32 | VDD — Positive supply (2.5 V to 6.0 V) |
| ピン 33 | RB0/INT — PORTB bit 0 / external interrupt |
| ピン 34 | RB1 — PORTB bit 1 |
| ピン 35 | RB2 — PORTB bit 2 |
| ピン 36 | RB3 — PORTB bit 3 / low-voltage programming |
| ピン 37 | RB4 — PORTB bit 4 |
| ピン 38 | RB5 — PORTB bit 5 |
| ピン 39 | RB6/PGC — PORTB bit 6 / ICSP clock |
| ピン 40 | RB7/PGD — PORTB bit 7 / ICSP data |
| ピン 41 | NC — Not connected (per datasheet) |
| ピン 42 | NC — Not connected (per datasheet) |
| ピン 43 | NC — Not connected (per datasheet) |
| ピン 44 | NC — Not connected (per datasheet) |
主な用途
PIC16C64A-20E/PT の用途: 6 件s: Industrial Control Systems, Appliance and White-Goods Control, Automotive Body Electronics, Test and Measurement Instrumentation, HVAC and Building Automation, Embedded Educational Platforms.
Industrial Control Systems
The PIC16C64A-20E/PT's 20 MHz CPU and 33 digital I/O pins give it ample throughput to scan sensors, drive relays, and orchestrate PID loops in PLCs and motor starters. Its extended -40 °C to +125 °C operating range supports deployment inside unventilated control cabinets where ambient temperatures swing widely. The integrated USART plus the SSP (SPI/I²C) module eliminate external bridge ICs when talking to digital sensors and EEPROMs, while the 8-channel 8-bit ADC handles analog feedback from transducers. Because OTP memory is written once and is permanent, this part suits only fully validated control firmware that has finished its design-cycle iteration phase. Use the PIC16F74-I/PT flash variant if any field firmware revision is anticipated. The TQFP-44 package exposes enough I/O to control a four-quadrant H-bridge with brake and enable logic on a single chip.
おすすめ
Appliance and White-Goods Control
The PIC16C64A-20E/PT integrates the peripherals needed for washing machines, dishwashers, microwave ovens, and refrigerator controllers - 33 I/O for keypad, LED display, motor relay, and triac interfaces, plus PWM for valve and pump control. The CCP module generates accurate timing signals for triac firing, while Timer1's gate-mode capability supports low-power standby with battery-backed RTC operation. The 2.5 V to 6.0 V supply range matches directly with rectified 5 V rails from small SMPS bricks inside appliances. The extended -40 °C to +125 °C operating range tolerates the temperature peaks near motor housings. Because these designs ship millions of units, the OTP memory model reduces per-unit cost relative to flash. Engineers should still provision an in-system programming header during design to recover from a misprogrammed batch.
おすすめ
Automotive Body Electronics
The PIC16C64A-20E/PT's extended -40 °C to +125 °C temperature grade and 33 I/O pins make it a fit for under-hood and body-domain modules such as wiper controllers, mirror positioners, seat controllers, and HVAC blend-door actuators. Its USART plus SSP provide the serial channels required to interface with LIN transceivers and dashboard clusters. The PIC16C64A is not AEC-Q100 qualified, so for safety-critical ECUs a Q-graded part such as the PIC16F74-I/PT is required, but for body-control convenience loads the standard grade is widely deployed in pre-AEC-Q100 design eras. The 20 MHz execution speed handles CAN-LIN gateway timing without external logic, and the watchdog timer plus brown-out reset cover the electrical noise environment of an automotive 12 V bus.
おすすめ
Test and Measurement Instrumentation
The PIC16C64A-20E/PT's 20 MHz throughput, integrated 8-channel 8-bit ADC, and PWM output make it a cost-effective controller for hand-held multimeters, bench DMMs, panel meters, and simple data loggers. The ADC input channels accept signal-conditioned analog signals from current shunts, voltage dividers, and temperature sensors such as thermistors. The PWM drives LCD contrast bias and buzzer alert tones without a dedicated audio DAC. The USART streams measured values to a host PC over RS-232 or RS-485, while the SSP port supports SPI displays or external EEPROMs for logged data storage. The 128-byte RAM is sufficient for running-average and peak-hold algorithms on the ADC stream. Because OTP memory is single-shot, this part suits fully characterised instrumentation where calibration coefficients are fixed at production.
おすすめ
HVAC and Building Automation
The PIC16C64A-20E/PT delivers the digital I/O count needed for thermostat, damper actuator, and zone controller designs. The 33 I/O pins support multiple push-button inputs, triac outputs for compressor and fan control, and LCD segment drivers. The USART plus SSP interfaces with central building controllers via RS-485 or Modbus using a small external transceiver. The extended temperature range tolerates plenum and rooftop equipment enclosures. The PWM drives proportional valves and variable-speed fan references, while the 8-bit ADC reads thermistor, humidity sensor, and pressure transducer inputs. Use the PIC16F74-I/PT if firmware updates are anticipated for seasonal control law refinements, otherwise OTP ensures a fixed unit price over the product lifetime.
おすすめ
Embedded Educational Platforms
The PIC16C64A-20E/PT is a classical teaching vehicle for Harvard-architecture 8-bit microcontrollers. Its 35-instruction RISC-style instruction set, 14-bit program word, and visible peripheral registers give students a clean view of MCU internals without abstraction layers. The 20 MHz execution speed is fast enough to demonstrate real-time signal processing, while the integrated USART and SSP let students build serial and I²C peripherals from scratch. The 44-pin TQFP package exposes every I/O for breadboard adapter boards, and the extended temperature range supports lab equipment use. Because the PIC16C64A is OTP, classroom exercises typically use the equivalent PIC16F74-I/PT flash part on the same footprint so that students can repeatedly reprogram and iterate. The PIC16C64A-20E/PT remains a useful reference device for studying the architectural lineage leading to modern PIC16F1xxx parts.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: PIC16C64A-20E/PT — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | PIC16C64A-10I/PT | PIC16C64A-04I/PT | PIC16C64A-04E/PT | PIC16C65B-20E/PT | PIC16F74-I/PT |
|---|---|---|---|---|---|---|
| Package | TQFP-44 (PT) 10x10 mm | TQFP-44 (PT) 10x10 mm - same | TQFP-44 (PT) 10x10 mm - same | TQFP-44 (PT) 10x10 mm - same | TQFP-44 (PT) 10x10 mm - same | TQFP-44 (PT) 10x10 mm - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program Memory | 3.5 KB OTP | 3.5 KB OTP | 3.5 KB OTP | 3.5 KB OTP | 7 KB OTP | 7 KB Flash |
| Max CPU Frequency | 20 MHz | 10 MHz | 4 MHz | 4 MHz | 20 MHz | 20 MHz |
| Temperature Range | -40C to +125C (E) | -40C to +85C (I) | -40C to +85C (I) | -40C to +125C (E) | -40C to +125C (E) | -40C to +85C (I) |
| Memory Type | OTP EPROM | OTP EPROM | OTP EPROM | OTP EPROM | OTP EPROM | Flash (in-circuit reprogrammable) |
| RAM | 128 bytes | 128 bytes | 128 bytes | 128 bytes | 192 bytes | 192 bytes |
| I/O Pins | 33 | 33 | 33 | 33 | 33 | 33 |
| ADC | 8-bit, 8 channels | 8-bit, 8 channels | 8-bit, 8 channels | 8-bit, 8 channels | 8-bit, 8 channels | 8-bit, 8 channels |
| Lifecycle Status | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete | Active |
主な差別化要因
- Highest CPU frequency in the PIC16C64A family （vs PIC16C64A-10I/PT)
- Extended -40C to +125C temperature grade （vs PIC16C64A-10I/PT)
- More code space than other speed grades （vs PIC16C64A-04E/PT)
- Drop-in OTP path with second USART （vs PIC16C65B-20E/PT)
- Pin-compatibility with flash migration path （vs PIC16F74-I/PT)
設計ノート
Estimated: the PIC16C64A-20E/PT draws a typical operating supply current of approximately 5 mA at 5 V and 20 MHz and a quiescent current under 1 uA in sleep mode, so a 100 nF decoupling capacitor placed within 5 mm of each VDD/VSS pair (pins 11/12 and 31/32) is required to suppress switching transients. Add a bulk 10 uF tantalum or ceramic capacitor at the supply entry point. The MCLR/VPP pin on pin 1 needs a 10 kohm pull-up to VDD for normal operation; if in-circuit serial programming is desired, route MCLR through a diode-resistor network so that the programmer's VPP can overdrive it without disturbing the rest of the system.
Route the two oscillator pins (OSC1/CLKIN on pin 13 and OSC2/CLKOUT on pin 14) as a guarded differential pair with a ground ring on both sides. Keep the crystal, loading capacitors, and series resistor within 8 mm of the MCU. For high-speed 20 MHz operation, choose a crystal with an ESR under 60 ohm and an effective load capacitance matched to your capacitor choice. Avoid routing digital switching signals under or adjacent to the oscillator traces, because capacitive coupling can shift the operating frequency and increase jitter.
Because the PIC16C64A-20E/PT uses One-Time Programmable memory, there is no way to recover from a programming error without physically replacing the part. Always validate the full configuration word, ID locations, oscillator calibration, and code checksum in a PICkit or ICD socket emulator before committing the OTP array. Verify VDD during programming stays above 4.5 V (per datasheet DS30261 VDD specification) because brown-outs during the OTP write can corrupt the entire device. Production programmers should issue a post-program verify and read back the entire code space to catch bit errors before socket insertion.
Allocate each PORTB pin (RB0-RB7 on pins 33-40) with a 100 ohm series resistor when driving external loads, because PORTB has internal weak pull-ups but limited sink current. PORTD pins (RD0-RD7 on pins 19-22 and 27-30) and PORTC UART pins (RC6/RC7 on pins 25-26) are commonly routed to off-board connectors and benefit from TVS diodes and 100 ohm termination for ESD protection. Keep the analog inputs (RA0-RA5, RE0-RE2) physically separated from the digital switching lines by a ground trace, and use a star-ground topology returning all analog returns to a single point near the AVSS/VDD pair.
コンプライアンス情報
Lead-free matte-tin finish (lead-free PT suffix). RoHS compliant per Microchip product page. The PIC16C64A is not AEC-Q100 qualified; AEC-Q100 automotive parts require the PIC16F or dsPIC33 families.