PIC16C74A-04I/P - 8-Bit 4MHz 7KB OTP MCU 40-PDIP | Microchip
部品番号: PIC16C74A-04I/P ✗ 生産終了| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $12.5 | $12.50 |
| 10 | $11.25 | $112.50 |
| 100 | $10 | $1,000.00 |
| 500 | $8.75 | $4,375.00 |
| 1,000 | $7.5 | $7,500.00 |
PIC16C74A-04I/P 概要
An 8-bit microcontroller (MCU) is a small computer-on-a-chip that integrates a CPU, RAM, non-volatile program memory, and peripheral interfaces into a single IC. PIC16C microcontrollers sit in the broader PIC mid-range family hierarchy: PIC16C -> PIC mid-range -> 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. These MCUs serve as the main controller in embedded systems, executing firmware stored in on-chip memory to read sensors, drive actuators, and communicate with other ICs.
Key features of the PIC16C74A-04I/P include a wide operating voltage range of 2.5 V to 6.0 V, 33 digital I/O pins, high sink/source current of 25 mA per pin suitable for direct LED drive, and low-power consumption of 15 uA typical at 5 V/4 MHz plus 1 uA standby at 3 V/32 kHz. The integrated peripherals comprise three timers, a USART, an SSP, and a capture/compare/PWM module.
The architecture employs a Harvard design with separate program and data buses, enabling simultaneous instruction fetch and data access. The 14-bit instruction word provides more opcode space than 12-bit PIC cores, enabling richer addressing modes and larger immediate operands. The OTP EPROM program memory allows one-time programming using standard EPROM programmers, while the 192-byte data RAM supports general variables and stack operations.
Typical applications include industrial control systems, motor control, instrumentation, consumer electronics, and automotive subsystems. The industrial temperature range (-40C to +85C) makes it suitable for factory automation and outdoor equipment where commercial-grade parts are insufficient.
When designing with the PIC16C74A, ensure the 4 MHz clock limit is respected - higher-frequency variants (PIC16C74B at 20 MHz) exist if more performance is needed. The OTP memory cannot be re-programmed, so code must be fully verified before burning; for in-circuit reprogrammability, consider the flash-based PIC16F74.
This page synthesizes distributor pricing, drop-in compatible alternatives, and practical design notes not found in the manufacturer datasheet.
ドロップイン代替品: PIC16C74A-04I/P — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: PIC16C74A-04I/P （同一形状・フットプリント） — 相違点: Package, Core Architecture, Timers, Operating Temperature Range, Program Memory Type.
クイック比較ツール — 並列比較する代替部品を選択:
PIC16C74B-04I/P
✅ ドロップイン✓ 在庫あり
$5.55 / 個
データシートを見る →PIC16C74B-20I/P
✅ ドロップイン✓ 在庫あり
$6.78 / 個
データシートを見る →PIC16F74-I/P
✅ ドロップイン✓ 在庫あり
価格はお問い合わせください
データシートを見る →PIC16C74A-04/PQ
✅ ドロップイン✓ 在庫あり
$5.8 / 個
データシートを見る →PIC16C74A-20I/P
✅ ドロップイン✓ 在庫あり
$8.74 / 個
データシートを見る →PIC16C77-04I/P
✅ ドロップイン✓ 在庫あり
$6.05 / 個
データシートを見る →PIC16C74A-04I/P 最大定格＆電気的特性
| Core Architecture | PIC 8-bit RISC (Harvard) |
| Program Memory Type | OTP EPROM |
| Program Memory Size | 7 KB (4K x 14) |
| RAM Size | 192 bytes |
| Data EEPROM | 0 bytes (not present) |
| 最大クロック周波数 | 4 MHz |
| Operating Voltage Range | 2.5 V to 6.0 V (typical 4.0 V to 5.5 V) |
| Digital I/O Pins | 33 |
| ADC | 8 channels x 8-bit |
| Timers | 3 (Timer0, Timer1, Timer2) |
| Communication Peripherals | USART, SSP (SPI/I2C) |
| Capture/Compare/PWM | 1 CCP module |
| I/O Sink/Source Current | 25 mA / 25 mA per pin |
| 動作温度範囲 | -40 C to +85 C (Industrial) |
| パッケージ | 40-pin PDIP (DIP-40) |
| 実装タイプ | Through-Hole |
| RoHS ステータス | Non-Compliant (contains lead) |
| Instruction Set | 35 single-word instructions |
| Reset | POR, MCLR, WDT |
| Watchdog Timer | Yes |
PIC16C74A-04I/P ピン構成
| ピン 1 | MCLR — Master Clear (reset, active low) |
| ピン 2 | RA0/AN0 — PORTA bit 0 / Analog input 0 |
| ピン 3 | RA1/AN1 — PORTA bit 1 / Analog input 1 |
| ピン 4 | RA2/AN2 — PORTA bit 2 / Analog input 2 |
| ピン 5 | RA3/AN3/VREF — PORTA bit 3 / Analog input 3 / Voltage reference |
| ピン 6 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| ピン 7 | RA5/AN4/SS — PORTA bit 5 / Analog input 4 / SPI slave select |
| ピン 8 | RE0/RD/AN5 — PORTE bit 0 / Read control / Analog input 5 |
| ピン 9 | RE1/WR/AN6 — PORTE bit 1 / Write control / Analog input 6 |
| ピン 10 | RE2/CS/AN7 — PORTE bit 2 / Chip select / Analog input 7 |
| ピン 11 | VDD — Positive supply voltage |
| ピン 12 | VSS — Ground |
| ピン 13 | OSC1/CLKIN — Oscillator crystal input / external clock |
| ピン 14 | OSC2/CLKOUT — Oscillator crystal output / clock out |
| ピン 15 | RC0/T1OSO/T1CKI — PORTC bit 0 / Timer1 oscillator output / Timer1 clock |
| ピン 16 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator input / CCP2 |
| ピン 17 | RC2/CCP1 — PORTC bit 2 / Capture Compare PWM 1 |
| ピン 18 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I2C clock |
| ピン 19 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| ピン 20 | RC5/SDO — PORTC bit 5 / SPI data out |
| ピン 21 | RC6/TX/CK — PORTC bit 6 / USART transmit / USART clock |
| ピン 22 | RC7/RX/DT — PORTC bit 7 / USART receive / USART data |
| ピン 23 | RD0/PSP0 — PORTD bit 0 / Parallel Slave Port bit 0 |
| ピン 24 | RD1/PSP1 — PORTD bit 1 / Parallel Slave Port bit 1 |
| ピン 25 | RD2/PSP2 — PORTD bit 2 / Parallel Slave Port bit 2 |
| ピン 26 | RD3/PSP3 — PORTD bit 3 / Parallel Slave Port bit 3 |
| ピン 27 | RD4/PSP4 — PORTD bit 4 / Parallel Slave Port bit 4 |
| ピン 28 | RD5/PSP5 — PORTD bit 5 / Parallel Slave Port bit 5 |
| ピン 29 | RD6/PSP6 — PORTD bit 6 / Parallel Slave Port bit 6 |
| ピン 30 | RD7/PSP7 — PORTD bit 7 / Parallel Slave Port bit 7 |
| ピン 31 | VSS — Ground |
| ピン 32 | VDD — Positive supply voltage |
| ピン 33 | RB0/INT — PORTB bit 0 / External interrupt |
| ピン 34 | RB1 — PORTB bit 1 |
| ピン 35 | RB2 — PORTB bit 2 |
| ピン 36 | RB3/PGM — PORTB bit 3 / Low-voltage programming |
| ピン 37 | RB4 — PORTB bit 4 |
| ピン 38 | RB5 — PORTB bit 5 |
| ピン 39 | RB6/PGC — PORTB bit 6 / ICSP clock |
| ピン 40 | RB7/PGD — PORTB bit 7 / ICSP data |
主な用途
PIC16C74A-04I/P の用途: 6 件s: Industrial Control Systems, Motor Control and PWM Drives, Consumer Electronics and Appliances, Instrumentation and Data Acquisition, Automotive Body and Chassis Electronics, Educational and Hobby Projects.
Industrial Control Systems
The PIC16C74A-04I/P is well-suited for industrial control applications including PLCs, sensor interfaces, and actuator drivers. Its 33 digital I/O pins and 25 mA sink/source capability allow direct LED and relay drive without external transistors, reducing BOM cost. The 8-channel 8-bit ADC enables direct connection to temperature, pressure, and flow sensors common in factory automation. Industrial temperature range (-40 C to +85 C) supports harsh factory environments where commercial-grade parts fail.
おすすめ
Motor Control and PWM Drives
The integrated Capture/Compare/PWM (CCP) module and three timers make PIC16C74A-04I/P suitable for brushed DC motor speed control, stepper motor sequencing, and small BLDC applications. The 25 mA I/O drive can handle small signal MOSFET gates directly. For higher-current motors, pair with external H-bridge drivers. The 4 MHz clock provides adequate PWM resolution for motor speeds up to several thousand RPM at typical switching frequencies of 1-10 kHz.
おすすめ
Consumer Electronics and Appliances
The PIC16C74A-04I/P fits consumer products like washing machine controllers, microwave oven interfaces, and HVAC thermostats where the OTP memory provides low unit cost and the 192-byte RAM handles user interface state machines. Low power consumption (15 uA at 4 MHz/5V, 1 uA standby) suits battery-backed appliance applications. The wide 2.5 V to 6.0 V supply range allows direct operation from rectified mains or battery sources.
おすすめ
Instrumentation and Data Acquisition
With its 8-channel 8-bit ADC and USART/SSP peripherals, PIC16C74A-04I/P serves as a compact data acquisition front-end for laboratory instruments and test equipment. The 4 MIPS CPU speed at 4 MHz handles 1 kHz sample rates with on-chip averaging. The PIC16C74A-04I/P can serve as a sensor hub aggregating analog signals and forwarding digital data to a host PC via RS-232. Industrial temperature grade supports lab and field deployments.
おすすめ
Automotive Body and Chassis Electronics
The industrial temperature range and rugged PDIP packaging of PIC16C74A-04I/P make it applicable to non-safety automotive systems like seat controllers, window lift modules, and instrument cluster sub-functions. The 33 I/O pins and USART enable CAN/LIN gateway implementations when paired with external transceivers. Note: AEC-Q100 qualification is NOT present on this part; for safety-critical systems, choose PIC16F74-I/P or PIC18F equivalent with automotive grade.
おすすめ
Educational and Hobby Projects
The PIC16C74A-04I/P is widely used in university embedded systems courses and DIY electronics due to its through-hole PDIP-40 package that fits standard breadboards and ZIF sockets. Its mature instruction set and abundant online code examples make it ideal for teaching RISC architecture fundamentals. However, the OTP memory requires an external EPROM programmer, which adds cost; the flash-based PIC16F74-I/P is often preferred for educational settings requiring repeated code iteration.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: PIC16C74A-04I/P — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | PIC16C74B-04I/P | PIC16C74B-20I/P | PIC16F74-I/P | PIC16C74A-04/PQ |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | PDIP-40 | PDIP-40 - same | PDIP-40 - same | PDIP-40 - same | PDIP-40 - same |
| Max Clock Frequency | 4 MHz | 4 MHz | 20 MHz (+400%) | 20 MHz (+400%) | 4 MHz |
| Program Memory Type | OTP EPROM (7KB) | OTP EPROM (7KB) | OTP EPROM (7KB) | Flash (7KB, reprogrammable) | OTP EPROM (7KB) |
| RAM Size | 192 bytes | 192 bytes | 192 bytes | 192 bytes | 192 bytes |
| Temperature Range | -40C to +85C (Industrial) | -40C to +85C (Industrial) | -40C to +85C (Industrial) | -40C to +85C (Industrial) | 0C to +70C (Commercial) |
| ADC | 8-ch x 8-bit | 8-ch x 8-bit | 8-ch x 8-bit | 8-ch x 8-bit | 8-ch x 8-bit |
| RoHS Status | Non-compliant (Pb) | Non-compliant (Pb) | Non-compliant (Pb) | Compliant | Non-compliant (Pb) |
| Lifecycle Status | NRND | NRND | NRND | Active | NRND |
主な差別化要因
- Industrial temperature range (-40C to +85C) （vs PIC16C74A-04/PQ)
- Established OTP-based design heritage （vs PIC16F74-I/P)
- Mid-range PIC compatibility （vs PIC16C74B-04I/P)
設計ノート
Estimated: At 5 V supply and 4 MHz clock, PIC16C74A-04I/P consumes approximately 15 mA active and 1 uA standby according to Microchip datasheet DC characteristics. Add 10 uF bulk and 0.1 uF decoupling ceramic capacitor close to VDD pins (11 and 32) to suppress switching noise. The two VDD/VSS pin pairs should both be connected - leaving one pair floating can cause erratic operation or reset glitches under load.
For the 40-pin PDIP package, place the IC in a DIP-40 socket for prototyping to allow easy replacement. Keep crystal/oscillator traces short (under 10 mm) and route them away from high-current digital lines to prevent clock corruption. MCLR pin (pin 1) requires a 10 kohm pull-up to VDD and a 100 nF capacitor to ground for proper reset behavior - omitting these causes intermittent reset failures.
Do not confuse PIC16C74A (4 MHz, OTP) with PIC16C74B (20 MHz, OTP) or PIC16F74 (20 MHz, Flash) - the speed suffixes and memory types differ significantly. The OTP memory of PIC16C74A-04I/P cannot be erased, so each burned part is one-time use; verify code thoroughly before programming. According to Microchip, this part is NRND - new designs should consider PIC16F74-I/P for flash reprogrammability and active lifecycle support.
コンプライアンス情報
Non-RoHS PDIP-40 package with SnPb plating. Not AEC-Q100 qualified - choose PIC16F74 automotive variants for safety-critical designs. REACH and conflict minerals compliance per Microchip material declarations.
