PIC16C74B-04E/P - 8-bit OTP MCU, 7KB EPROM, 4MHz, 40-PDIP | Microchip
部品番号: PIC16C74B-04E/P ✗ 生産終了| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $8.9 | $8.90 |
| 10 | $7.95 | $79.50 |
| 100 | $6.85 | $685.00 |
| 500 | $5.95 | $2,975.00 |
| 1,000 | $5.4 | $5,400.00 |
PIC16C74B-04E/P 概要
An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path, optimized for deterministic control of low-to-medium complexity embedded systems. PIC microcontrollers belong to the Harvard-architecture RISC family of MCUs, a category that sits within the broader microcontroller IC taxonomy (MCU -> microcontroller -> embedded processor -> semiconductor). The PIC16C mid-range family is upwards compatible with the PIC16C5X baseline family, allowing code reuse across generations.
Key features of the PIC16C74B include wide operating voltage from 2.0 V to 6.0 V, 25 mA source/sink current per I/O, and low-power operation with typical standby current of 15 µA at 5 V/4 MHz and 1 µA at 3 V/32 kHz. The device supports commercial, industrial, and extended temperature ranges, making it suitable for cost-sensitive industrial and consumer designs requiring robust digital I/O and integrated analog.
Technically, the PIC16C74B uses a 14-bit instruction word and a Harvard bus architecture with separate program and data paths, enabling single-cycle instruction fetch and decode. Its 35 single-word instruction set simplifies assembly development, while the integrated peripherals reduce external component count for typical control loops, sensor interfacing, and communication bridging.
Typical applications include industrial control panels, motor control, sensor signal acquisition, embedded communications bridges, and consumer appliance controllers. The wide temperature range and EPROM-based program storage make it well suited for mature production runs that value supply longevity and field-proven firmware stability.
When designing with the PIC16C74B-04E/P, note that the OTP EPROM cannot be erased, so code is final after programming - consider the PIC16F74 flash variant for development and field updates. Decoupling capacitors of 0.1 µF should be placed close to VDD/VSS pins, and unused I/O should be configured as outputs low to minimize power consumption.
This page synthesizes distributor pricing, drop-in PIC16C74B family variants, and practical design notes not found in the standalone manufacturer datasheet, helping engineers accelerate selection and sourcing.
ドロップイン代替品: PIC16C74B-04E/P — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: PIC16C74B-04E/P （同一形状・フットプリント） — 相違点: Mounting Type, Package, Serial Interfaces, Timers, A/D Converter.
クイック比較ツール — 並列比較する代替部品を選択:
PIC16C74B-04/PQ
✅ ドロップイン✓ 在庫あり
$7.25 / 個
データシートを見る →PIC16C74B-04/PQ
✓ 在庫あり
$7.25 / 個
データシートを見る →PIC16C74B-04I/L
✓ 在庫あり
$2.61 / 個
データシートを見る →PIC16F74-I/P
✅ ドロップイン📋 参考代替品（カタログ未掲載）
PIC16F74-E/P
✅ ドロップイン✓ 在庫あり
$5.1 / 個
データシートを見る →PIC16C73B-04I/SP
✓ 在庫あり
$4.75 / 個
データシートを見る →PIC16F877-04E/P
✅ ドロップイン✓ 在庫あり
$0.57 / 個
データシートを見る →PIC16C74B-04E/P 最大定格＆電気的特性
| Core | PIC16C mid-range, 8-bit RISC |
| Instruction Set | 35 single-word instructions |
| Instruction Execution Time | 200 ns (4 MHz clock) |
| Program Memory Type | OTP EPROM |
| Program Memory Size | 7 KB (4K x 14) |
| RAM Size | 192 bytes |
| EEPROM Size | None |
| Number of I/O | 33 |
| A/D Converter | 8 channels, 8-bit resolution |
| Timers | 2 x 8-bit + 1 x 16-bit (TMR0/TMR1/TMR2) |
| Capture/Compare/PWM | 2 modules (CCP) |
| Serial Interfaces | 1 x SSP (SPI/I²C), 1 x USART |
| Operating Voltage | 2.0 V to 6.0 V |
| Operating Frequency | DC to 4 MHz |
| I/O Sink/Source Current | 25 mA / 25 mA |
| Standby Current | < 1 µA typical at 3 V / 32 kHz |
| 動作温度 | -40 °C to +125 °C (Extended, E suffix) |
| パッケージ | 40-pin PDIP (0.600 in / 15.24 mm) |
| 実装タイプ | Through-hole |
| MSLレベル | Not applicable (through-hole PDIP) |
| Speed Grade Suffix | 04 = 4 MHz maximum |
PIC16C74B-04E/P ピン構成
| ピン 1 | MCLR/VPP — Master Clear (reset) input / programming voltage input |
| ピン 2 | RA0/AN0 — PORTA bit 0 / A/D channel 0 |
| ピン 3 | RA1/AN1 — PORTA bit 1 / A/D channel 1 |
| ピン 4 | RA2/AN2 — PORTA bit 2 / A/D channel 2 |
| ピン 5 | RA3/AN3/VREF- — PORTA bit 3 / A/D channel 3 / A/D VREF- |
| ピン 6 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| ピン 7 | RA5/AN4/SS — PORTA bit 5 / A/D channel 4 / SSP slave select |
| ピン 8 | RB0/INT — PORTB bit 0 / external interrupt |
| ピン 9 | RB1 — PORTB bit 1 |
| ピン 10 | RB2 — PORTB bit 2 |
| ピン 11 | RB3/PGM — PORTB bit 3 / low-voltage programming |
| ピン 12 | RB4 — PORTB bit 4 |
| ピン 13 | RB5 — PORTB bit 5 |
| ピン 14 | RB6/PGC — PORTB bit 6 / ICSP clock |
| ピン 15 | RB7/PGD — PORTB bit 7 / ICSP data |
| ピン 16 | RC0/T1OSO/T1CKI — PORTC bit 0 / Timer1 oscillator out / Timer1 clock in |
| ピン 17 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator in / CCP2 |
| ピン 18 | RC2/CCP1 — PORTC bit 2 / CCP1 |
| ピン 19 | RC3/SCK/SCL — PORTC bit 3 / SSP clock (SPI/I²C) |
| ピン 20 | RC4/SDI/SDA — PORTC bit 4 / SSP data in (SPI) / I²C data |
| ピン 21 | RC5/SDO — PORTC bit 5 / SSP data out |
| ピン 22 | RC6/TX/CK — PORTC bit 6 / USART TX / USART clock |
| ピン 23 | RC7/RX/DT — PORTC bit 7 / USART RX / USART data |
| ピン 24 | OSC2/CLKOUT — Oscillator output / clock out |
| ピン 25 | OSC1/CLKIN — Oscillator input / clock in |
| ピン 26 | RD0 — PORTD bit 0 |
| ピン 27 | RD1 — PORTD bit 1 |
| ピン 28 | RD2 — PORTD bit 2 |
| ピン 29 | RD3 — PORTD bit 3 |
| ピン 30 | RD4 — PORTD bit 4 |
| ピン 31 | RD5 — PORTD bit 5 |
| ピン 32 | RD6 — PORTD bit 6 |
| ピン 33 | RD7 — PORTD bit 7 |
| ピン 34 | VSS — Logic ground |
| ピン 35 | VDD — Logic supply voltage |
| ピン 36 | RE0/RD/AN5 — PORTE bit 0 / parallel slave port read / A/D channel 5 |
| ピン 37 | RE1/WR/AN6 — PORTE bit 1 / parallel slave port write / A/D channel 6 |
| ピン 38 | RE2/CS/AN7 — PORTE bit 2 / parallel slave port chip select / A/D channel 7 |
| ピン 39 | AVSS — Analog ground |
| ピン 40 | AVDD — Analog supply voltage |
主な用途
PIC16C74B-04E/P の用途: 6 件s: Industrial Control Panels, Motor Control and PWM Drive, Sensor Signal Acquisition, Embedded Communication Bridges, Consumer Appliance Controllers, Hobbyist and Educational Projects.
Industrial Control Panels
The PIC16C74B-04E/P fits industrial control panels because its 33 digital I/O pins drive relays, contactors, and indicator LEDs directly with 25 mA source/sink per pin, eliminating driver transistors in many circuits. Its 8-channel 8-bit A/D reads potentiometers, 4-20 mA loop shunts, and temperature sensors with sufficient resolution for HMI feedback loops. The Extended -40 °C to +125 °C temperature rating supports outdoor cabinet and factory-floor installations where ambient swings are common. Pair the part with the PIC16F74-I/P during development to enable flash-based firmware iteration, then transition to PIC16C74B-04E/P for production runs that have locked firmware.
おすすめ
Motor Control and PWM Drive
The PIC16C74B-04E/P suits brushed DC motor control and small stepper drive because it integrates two Capture/Compare/PWM (CCP) modules generating 10-bit PWM at 4 MHz to drive MOSFET gate drivers. Its 16-bit TMR1 provides precise period measurement for closed-loop tachometer feedback, and the 8-bit A/D monitors motor current via a shunt amplifier. The wide 2.0 V to 6.0 V supply range supports both 3.3 V logic and 5 V drive electronics. For higher-performance BLDC control, migrate to PIC18F family; for cost-sensitive brushed applications the PIC16C74B-04E/P is sufficient.
おすすめ
Sensor Signal Acquisition
The PIC16C74B-04E/P integrates an 8-channel 8-bit A/D converter with 4 µs typical conversion time at 4 MHz, enough for thermocouple conditioning, photodiode readout, and process-variable scanning at low rates. The 192-byte RAM buffers sample windows before UART transmission to a host, and the SSP module supports I²C sensor expansion (e.g., external ADCs, digital temperature ICs) for applications needing more analog channels. The Extended temperature rating allows installation near process heat sources. For higher-precision sensor systems, consider PIC16F1765 or PIC18F family MCUs with 10-/12-bit A/D converters.
おすすめ
Embedded Communication Bridges
The PIC16C74B-04E/P serves as a protocol-translation bridge because it combines an SSP module (configurable as SPI master/slave or I²C master/slave) with a separate USART supporting RS-232/RS-485 framing. This enables UART-to-I²C, SPI-to-UART, and Modbus-to-sensor-bus gateways in a single chip. The 35-instruction RISC core keeps translation latency low, and the 4 MIPS throughput handles message rates typical of building-automation and access-control networks. Pair with an external RS-485 transceiver for industrial multi-drop networks.
おすすめ
Consumer Appliance Controllers
The PIC16C74B-04E/P fits consumer appliance controllers (washing machines, dishwashers, small kitchen appliances) because its 33 I/O pins interface keypads, seven-segment displays, buzzer drivers, and triac control signals without external muxes. The 25 mA per-pin drive eliminates some relay drivers, and the 1 µA typical standby current at 3 V/32 kHz supports battery-backed real-time-clock operation during power-down. The OTP EPROM locks firmware at production, preventing post-sale code tampering in consumer markets. The Extended temperature rating supports under-counter and outdoor installations.
おすすめ
Hobbyist and Educational Projects
The PIC16C74B-04E/P is widely available through distributors and educational channels because of its mature 35-instruction PIC16C mid-range architecture, which is well documented in textbooks and online tutorials. The 40-pin PDIP through-hole package is breadboard-friendly, allowing students and hobbyists to prototype without SMD rework tools. Its USART, SPI/I²C, A/D, PWM, and 33 I/O give exposure to nearly every embedded peripheral category in a single chip. For learners, the PIC16F84A and PIC16F877A are typical alternatives; the PIC16C74B-04E/P provides a larger peripheral set for advanced learning projects.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: PIC16C74B-04E/P — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | PIC16C74B-04/P | PIC16F74-I/P | PIC16F74-E/P | PIC16F877-04E/P |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 40-pin PDIP | 40-pin PDIP - same | 40-pin PDIP - same | 40-pin PDIP - same | 40-pin PDIP - same |
| Program Memory | 7 KB OTP EPROM | 7 KB OTP EPROM | 7 KB flash | 7 KB flash | 14 KB flash |
| RAM | 192 bytes | 192 bytes | 192 bytes | 192 bytes | 368 bytes |
| Maximum Clock | 4 MHz | 4 MHz | 20 MHz | 20 MHz | 20 MHz |
| Operating Temperature | -40 °C to +125 °C (E suffix) | 0 °C to +70 °C | -40 °C to +85 °C (I suffix) | -40 °C to +125 °C (E suffix) | -40 °C to +125 °C (E suffix) |
| I/O Pins | 33 | 33 | 33 | 33 | 33 |
| A/D Converter | 8 ch × 8-bit | 8 ch × 8-bit | 8 ch × 8-bit | 8 ch × 8-bit | 8 ch × 10-bit |
| Memory Type | OTP EPROM (one-time) | OTP EPROM | Flash (reprogrammable) | Flash (reprogrammable) | Flash (reprogrammable) |
| Lifecycle Status | NRND | NRND | Active | Active | Active |
主な差別化要因
- Mature PIC16C mid-range architecture with extensive documentation （vs PIC16F74-I/P)
- Wider operating voltage range than typical flash PICs （vs PIC16F74-I/P)
- Larger program memory than PIC16C73B family （vs PIC16C73B-04I/SP)
設計ノート
Estimated: at VDD = 5 V and 4 MHz oscillator with all peripherals enabled and I/O sourcing 25 mA, total current draw is approximately 15-20 mA during active execution and < 1 µA in sleep mode. Place a 0.1 µF decoupling capacitor within 5 mm of each VDD pin (pin 11, pin 32) and a 10 µF bulk capacitor near the MCU supply. AVDD/AVSS should be tied to VDD/VSS respectively with a ferrite bead or 10 Ω resistor plus 0.1 µF cap for A/D noise isolation. Brown-out reset should be enabled in the configuration bits for reliable cold-start behavior at 2.0-6.0 V operation.
The 40-pin PDIP package has a junction-to-ambient thermal resistance of approximately 70 °C/W, which is acceptable for typical MCU workloads below 100 mW. The Extended temperature suffix 'E' guarantees -40 °C to +125 °C operation; derating is not normally required for through-hole PDIP. If the part is mounted in a sealed enclosure with limited airflow, ensure ambient at the package does not exceed 85 °C to maintain margin. At maximum oscillator frequency and all peripherals active, internal dissipation is well under 50 mW; no heatsink is required.
Layout guidelines: (1) Place the 4 MHz crystal or resonator within 5 mm of OSC1/OSC2 (pins 25/24) and route ground side of crystal load capacitors directly to a single VSS via; (2) keep analog traces (PORTE) physically apart from digital switching signals (PORTD, USART) to minimize A/D crosstalk; (3) MCLR/VPP (pin 1) requires a 10 kΩ pull-up to VDD and a 100 nF decoupling cap if using ICSP; (4) unused I/O should be configured as outputs low to minimize current consumption; (5) the parallel slave port pins RE0/RE1/RE2 should be tied to known states if PSP is unused.
Common pitfalls: (1) The '04' speed suffix limits clock to 4 MHz - do not overclock to PIC16F74's 20 MHz, the OTP EPROM timing will not support it; (2) OTP EPROM cannot be erased, so use PIC16F74-I/P for development and lock firmware only after final code is verified; (3) configuration word must be set explicitly for oscillator type (HS/RC/XT), watchdog timer, brown-out reset, and code protection - default unprogrammed configuration may not match design intent; (4) the A/D converter requires ADCON1 register configuration to enable analog pins; digital I/O on PORTE must be disabled before sampling; (5) ICD debugging requires dedicated RB6/RB7 pins which are also general I/O.
コンプライアンス情報
RoHS / lead-free status was not provided in the Verified Web Data and is not stated on the Microchip product page for the PIC16C74B family. PIC16C74B is a legacy OTP part; customers should request the latest RoHS / material declaration directly from Microchip. AEC-Q100 is not applicable for non-automotive-spec'd MCUs.
