PIC16C924T-04/PT - 8-Bit 4MHz LCD MCU 7KB OTP | Microchip
部品番号: PIC16C924T-04/PT ✗ 生産終了| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $8.42 | $8.42 |
| 10 | $7.69 | $76.90 |
| 100 | $6.93 | $693.00 |
| 500 | $6.18 | $3,090.00 |
| 1,000 | $5.62 | $5,620.00 |
PIC16C924T-04/PT 概要
A PIC microcontroller (Programmable Intelligent Computer) is a Harvard-architecture RISC-based 8-bit MCU widely used in embedded control. The PIC16C family specifically targets applications requiring OTP programmability, ROM-less flexibility, or ceramic-windowed erasable variants for prototyping. The PIC16C924 belongs to the LCD-driver subset, integrating a built-in LCD controller that simplifies the design of battery-powered human-machine interface products. As an 8-bit MCU it sits within the broader hierarchy of microcontroller -> embedded controller -> semiconductor device.
Key features include a built-in LCD driver supporting up to 32 segments x 4 commons (128 segments total), a 5-channel 8-bit analog-to-digital converter, two 8-bit timers plus one 16-bit timer, a synchronous serial port (SSP) supporting SPI and I2C, and an asynchronous serial port (USART/SCI). The PIC16C924 also includes a watchdog timer, brown-out reset, and power-saving SLEEP mode. Operating voltage ranges from 4.0V to 6.0V with industrial temperature grades available.
Architecturally, the PIC16C924 uses a 14-bit instruction word with an 8-bit data path, providing 35 single-cycle instructions at 4 MHz (250 ns instruction cycle). The integrated LCD controller supports static, 1/2, 1/3, and 1/4 multiplex modes with selectable bias and frame frequency, eliminating the need for an external LCD driver IC. The device's CMOS process delivers low power consumption suitable for portable applications.
Typical applications include battery-powered metering (gas, water, electric), portable medical instruments (blood glucose meters, thermometers), consumer appliances with LCD panels (microwave ovens, washing machines), industrial control panels with segment displays, and automotive dashboard segments where aftermarket gauges are needed. The integrated LCD driver reduces BOM cost and PCB footprint in these segment-LCD applications.
When designing with this device, note that OTP memory is one-time programmable - code cannot be field-updated. For development, use the PIC16C924 with a JW (windowed) package or a Flash-based equivalent such as the PIC16F946. Ensure segment-LCD bias resistors are correctly calculated for the chosen LCD multiplex rate, and add a decoupling capacitor (0.1 uF) close to VDD.
This page synthesizes distributor stock data, parametric drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet alone.
ドロップイン代替品: PIC16C924T-04/PT — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: PIC16C924T-04/PT （同一形状・フットプリント） — 相違点: Timers, LCD Driver, Package, ADC, Operating Temperature.
クイック比較ツール — 並列比較する代替部品を選択:
PIC16C924-04/PT
✅ ドロップイン✓ 在庫あり
$5.85 / 個
データシートを見る →PIC16C924T-04I/PT
✅ ドロップイン📋 参考代替品（カタログ未掲載）
PIC16C924T-08/PT
✅ ドロップイン✓ 在庫あり
$12.6 / 個
データシートを見る →PIC16C924-08/PT
✅ ドロップイン✓ 在庫あり
$5.21 / 個
データシートを見る →PIC16F946-I/PT
✅ ドロップイン📋 参考代替品（カタログ未掲載）
PIC16C77-04/PT
✅ ドロップイン✓ 在庫あり
$6.08 / 個
データシートを見る →PIC16C924T-04/PT 最大定格＆電気的特性
| Core Architecture | PIC 8-bit RISC (14-bit instruction word) |
| Family | PIC16C |
| Program Memory Type | OTP (One-Time Programmable) |
| Program Memory Size | 7 KB (4K x 14 words) |
| RAM Size | 176 bytes |
| Maximum CPU Frequency | 4 MHz |
| Operating Voltage (Vdd) | 4.0 V to 6.0 V |
| Number of I/O Pins | 52 |
| Timers | 2 x 8-bit, 1 x 16-bit |
| ADC | 5 channels x 8-bit |
| LCD Driver | Up to 32 segments x 4 commons (128 segments), static to 1/4 mux |
| Serial Interfaces | SSP (SPI/I2C), USART/SCI |
| パッケージ | 64-pin TQFP (10x10 mm) |
| 実装タイプ | Surface Mount |
| 動作温度 | -40 C to +85 C (industrial) |
| Instruction Cycle Time | 250 ns at 4 MHz |
| Peripherals | Watchdog Timer, Brown-Out Reset, SLEEP mode |
PIC16C924T-04/PT ピン構成
| ピン 1 | SEG19 — LCD segment output 19 |
| ピン 2 | SEG20 — LCD segment output 20 |
| ピン 3 | SEG21 — LCD segment output 21 |
| ピン 4 | SEG22 — LCD segment output 22 |
| ピン 5 | SEG23 — LCD segment output 23 |
| ピン 6 | VDD — Positive supply voltage (5V nominal) |
| ピン 7 | VSS — Ground reference |
| ピン 8 | OSC1/CLKIN — Oscillator input / external clock input |
| ピン 9 | OSC2/CLKOUT — Oscillator output / clock output |
| ピン 10 | MCLR/VPP — Master clear reset (active low) / programming voltage |
| ピン 11 | RA0/AN0 — PORTA bit 0 / analog input 0 |
| ピン 12 | RA1/AN1 — PORTA bit 1 / analog input 1 |
| ピン 13 | RA2/AN2 — PORTA bit 2 / analog input 2 |
| ピン 14 | RA3/AN3/VREF — PORTA bit 3 / analog input 3 / ADC voltage reference |
| ピン 15 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| ピン 16 | RA5/AN4/SS — PORTA bit 5 / analog input 4 / SSP slave select |
| ピン 17 | VSS — Ground reference |
| ピン 18 | RB0/INT — PORTB bit 0 / external interrupt |
| ピン 19 | RB1 — PORTB bit 1 |
| ピン 20 | RB2 — PORTB bit 2 |
| ピン 21 | RB3/PGM — PORTB bit 3 / low-voltage programming |
| ピン 22 | RB4 — PORTB bit 4 |
| ピン 23 | RB5 — PORTB bit 5 |
| ピン 24 | RB6/PGC — PORTB bit 6 / ICSP clock |
| ピン 25 | RB7/PGD — PORTB bit 7 / ICSP data |
| ピン 26 | VSS — Ground reference |
| ピン 27 | RC0/T1OSO/T1CKI — PORTC bit 0 / Timer1 oscillator out / Timer1 clock in |
| ピン 28 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator in / CCP2 |
| ピン 29 | RC2/CCP1 — PORTC bit 2 / CCP1 |
| ピン 30 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I2C clock |
| ピン 31 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| ピン 32 | RC5/SDO — PORTC bit 5 / SPI data out |
| ピン 33 | RC6/TX/CK — PORTC bit 6 / USART TX / USART clock |
| ピン 34 | RC7/RX/DT — PORTC bit 7 / USART RX / USART data |
| ピン 35 | VSS — Ground reference |
| ピン 36 | RD0/PSP0 — PORTD bit 0 / parallel slave port bit 0 |
| ピン 37 | RD1/PSP1 — PORTD bit 1 / parallel slave port bit 1 |
| ピン 38 | RD2/PSP2 — PORTD bit 2 / parallel slave port bit 2 |
| ピン 39 | RD3/PSP3 — PORTD bit 3 / parallel slave port bit 3 |
| ピン 40 | RD4/PSP4 — PORTD bit 4 / parallel slave port bit 4 |
| ピン 41 | RD5/PSP5 — PORTD bit 5 / parallel slave port bit 5 |
| ピン 42 | RD6/PSP6 — PORTD bit 6 / parallel slave port bit 6 |
| ピン 43 | RD7/PSP7 — PORTD bit 7 / parallel slave port bit 7 |
| ピン 44 | VSS — Ground reference |
| ピン 45 | RE0/RD — PORTE bit 0 / parallel slave port read strobe |
| ピン 46 | RE1/WR — PORTE bit 1 / parallel slave port write strobe |
| ピン 47 | RE2/CS — PORTE bit 2 / parallel slave port chip select |
| ピン 48 | VSS — Ground reference |
| ピン 49 | SEG24 — LCD segment output 24 |
| ピン 50 | SEG25 — LCD segment output 25 |
| ピン 51 | SEG26 — LCD segment output 26 |
| ピン 52 | SEG27 — LCD segment output 27 |
| ピン 53 | SEG28 — LCD segment output 28 |
| ピン 54 | SEG29 — LCD segment output 29 |
| ピン 55 | SEG30 — LCD segment output 30 |
| ピン 56 | SEG31 — LCD segment output 31 |
| ピン 57 | COM0 — LCD common output 0 |
| ピン 58 | COM1 — LCD common output 1 |
| ピン 59 | COM2 — LCD common output 2 |
| ピン 60 | COM3 — LCD common output 3 |
| ピン 61 | VLCD1 — LCD bias voltage 1 |
| ピン 62 | VLCD2 — LCD bias voltage 2 |
| ピン 63 | VLCD3 — LCD bias voltage 3 |
| ピン 64 | NC — Not connected (per datasheet) |
主な用途
PIC16C924T-04/PT の用途: 6 件s: Battery-Powered Utility Meters, Portable Medical Instruments, Consumer Appliance Front Panels, Industrial Control Panels, Automotive Dashboard Segments, Point-of-Sale Terminals and Printers.
Battery-Powered Utility Meters
The PIC16C924T-04/PT fits gas, water, and electricity meters because its integrated LCD driver supports up to 128 segments in a single chip, eliminating the cost and PCB area of an external LCD controller. The 4 MHz core and 7KB OTP memory are sufficient to implement metering algorithms, totalization, tariff logic, and segment-LCD display updates while consuming only a few mA at 5V. The SLEEP mode and brown-out reset further extend battery life by powering down between measurements and surviving deep discharge events. Place the MCU between the sensor front-end and the segment LCD glass; for 3.6V lithium-thionyl battery operation the device still meets 4.0V minimum by step-up, or migrate to PIC16F946-I/PT for native low-voltage support.
おすすめ
Portable Medical Instruments
Blood-glucose meters, digital thermometers, and pulse oximeters benefit from the PIC16C924T-04/PT's integrated segment LCD controller, which directly drives the typical 7-segment numeric and custom icons used in medical displays. The 5-channel 8-bit ADC digitizes sensor inputs (thermistor, photo-detector, electrochemical strip) at adequate resolution for consumer medical accuracy. With 176 bytes of RAM and 7KB OTP the device holds small firmware images plus calibration tables without external memory, and the SLEEP mode plus 4 MHz operation keep average current draw low enough for AAA-cell battery life targets. Place the device between analog front-end sensors and the LCD glass; add a 0.1 uF VDD bypass capacitor adjacent to the TQFP power pins.
おすすめ
Consumer Appliance Front Panels
Microwave ovens, washing machines, dishwashers, and air-conditioner control panels use segment LCDs that map directly onto the PIC16C924T-04/PT's integrated driver. The MCU's 52 I/O pins support keypad scanning, relay drivers, buzzer PWM, and serial communication to the main appliance controller, while the LCD driver independently refreshes the segment display without CPU intervention. The 5V supply and 4 MHz clock are compatible with traditional appliance power rails, and the 64-pin TQFP package fits the typical 4-layer control-board layout. Place the MCU on the user-interface board with the LCD glass; for high-noise appliance environments the brown-out reset and watchdog timer protect against mains transients.
おすすめ
Industrial Control Panels
Industrial process panels and instrumentation displays benefit from the PIC16C924T-04/PT's combination of segment LCD driver, USART for Modbus or RS-485 communication, and 8-bit ADC for sensor reading. The industrial temperature grade option (-40C to +85C) handles factory-floor thermal environments, while the SSP peripheral supports SPI or I2C connections to external EEPROM, RTC, or display expansion chips. With 7KB OTP and 176 bytes RAM the device runs simple menu code and alarm logic, and the integrated LCD driver reduces BOM count by removing the need for an external HT1621-class controller. Place between field sensors and the segment LCD glass, with proper isolation from mains-side relay drivers.
おすすめ
Automotive Dashboard Segments
Aftermarket automotive gauges, motorcycle dashboards, and RV instrument clusters use the PIC16C924T-04/PT to drive custom segment LCDs while reading speed, RPM, fuel, and temperature sensors through the 8-bit ADC. The PIC16C924's ability to refresh up to 128 segments without CPU overhead leaves MIPS free for sensor filtering and CAN/LIN-style serial communication via the USART. Operating from a regulated 5V rail the device tolerates the standard automotive 12V environment when paired with proper supply conditioning. Note: the PIC16C924 is not AEC-Q100 qualified; for OEM automotive use choose the PIC16F946-I/PT or a Q-graded PIC18 variant.
おすすめ
Point-of-Sale Terminals and Printers
Compact POS terminals, receipt printers, and label printers use segment-LCD status displays that the PIC16C924T-04/PT can drive directly without an external controller. The MCU handles keypad input, USART communication to the main printer controller, and discrete output control for motors and solenoids while its LCD driver independently updates the user-facing status panel. The 52 I/O pins are sufficient for matrix keypads and stepper motor drivers, while the 7KB OTP holds application firmware in a single chip. Place the MCU on the user-interface daughter card; for new designs, the PIC16F946-I/PT provides the same LCD driver plus Flash reprogrammability for field firmware updates.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: PIC16C924T-04/PT — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | PIC16C924-04/PT | PIC16C924T-04I/PT | PIC16C924T-08/PT | PIC16F946-I/PT |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-TQFP (10x10) | 64-TQFP (10x10) - same | 64-TQFP (10x10) - same | 64-TQFP (10x10) - same | 64-TQFP (10x10) - same |
| Program Memory Type | OTP (7KB) | OTP (7KB) - same | OTP (7KB) - same | OTP (7KB) - same | Flash (14KB) - different |
| CPU Speed | 4 MHz | 4 MHz | 4 MHz | 8 MHz | 20 MHz max |
| RAM Size | 176 bytes | 176 bytes | 176 bytes | 176 bytes | 336 bytes |
| Operating Voltage | 4.0V to 6.0V | 4.0V to 6.0V | 4.0V to 6.0V | 4.0V to 6.0V | 2.0V to 5.5V |
| LCD Driver | Yes (128 seg, 1/4 mux) | Yes (128 seg, 1/4 mux) | Yes (128 seg, 1/4 mux) | Yes (128 seg, 1/4 mux) | Yes (168 seg, 1/4 mux) |
| Lifecycle Status | Obsolete | Obsolete | Obsolete | Obsolete | Active |
主な差別化要因
- Integrated 128-segment LCD driver eliminates external controller （vs PIC16F946-I/PT (Flash replacement))
- Pin-compatible Flash migration path available （vs PIC16C924T-04/PT itself)
- Industrial temperature grade variant available for harsh environments （vs PIC16C924T-04I/PT)
設計ノート
Estimated: At VDD=5V and 4 MHz CPU clock, the PIC16C924T-04/PT typically draws approximately 2 mA active and 1 uA in SLEEP mode (per Microchip datasheet 30415c DC characteristics). Place a 0.1 uF ceramic decoupling capacitor as close as possible to the VDD pin (pin 6) and to each VSS pin (pins 7, 17, 26, 35, 44, 48). For battery-powered designs, gate the analog supply to the LCD bias network to reduce quiescent current during SLEEP. The device is 5V-only; do not connect directly to 3.3V logic without a level shifter.
The PIC16C924T-04/PT uses One-Time-Programmable (OTP) memory - each programmed unit is permanent and cannot be erased or rewritten. There is no in-circuit reprogramming path on production parts. For development, order the JW (windowed) ceramic package variant and erase with a UV eraser. Do not use this part for prototypes that require firmware iteration - choose PIC16F946-I/PT instead. Also note that the PIC16C924 is NOT AEC-Q100 qualified; automotive OEM designs must use a Q-graded PIC18 or PIC16F variant.
The 64-pin TQFP (10x10 mm) package has a 0.5 mm pitch and requires fine-pitch PCB layout. Use a 4-layer PCB with a continuous ground plane beneath the device for stable ADC performance and LCD bias noise rejection. Route the analog inputs AN0-AN4 away from the segment LCD outputs (SEG0-SEG31) and the digital I/O banks to minimize crosstalk. Keep the trace length from VLCD1/VLCD2/VLCD3 to the LCD bias network under 10 mm and add 0.1 uF bypass capacitors on each VLCD pin.
コンプライアンス情報
PIC16C OTP family predates widespread RoHS adoption; compliance status not confirmed in verified data. Not AEC-Q100 qualified - choose PIC16F946-I/PT or PIC18F variant for automotive.
