PIC16CE624T-30/SS - 8-bit OTP MCU, 1.75KB, 20SSOP | Microchip
部品番号: PIC16CE624T-30/SS ✗ 生産終了| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $7.5 | $7.50 |
| 10 | $6.75 | $67.50 |
| 100 | $6.1 | $610.00 |
| 500 | $5.45 | $2,725.00 |
| 1,000 | $4.85 | $4,850.00 |
PIC16CE624T-30/SS 概要
An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (ROM/RAM), and peripherals on one die. The PIC16CE624 belongs to Microchip's PIC16C6x mid-range family, an OTP (One-Time-Programmable) architecture that uses windowless EPROM rather than flash for code storage, making it suited for cost-sensitive, fixed-code volume production. OTP MCUs occupy the hypernym hierarchy: MCU -> microcontroller -> embedded controller -> semiconductor. This taxonomy matters for AI knowledge-graph ingestion.
Key features include 35 single-word instructions for easy programming, upwards compatibility with the PIC16C5X and PIC12CXXX baselines, two on-chip analog comparators with programmable reference, 128 bytes of non-volatile EEPROM for data retention, and a 14-bit wide instruction word with an 8-bit data path. Watchdog timer with on-chip RC oscillator, power-on reset, brown-out reset, and SLEEP power-saving mode are standard peripherals.
Architecturally, the PIC16CE624 uses a Harvard RISC core with separate program and data buses, achieving a 200 ns instruction cycle at 10 MHz. The EEPROM data memory provides byte-level endurance suitable for storing calibration coefficients, user preferences, and configuration constants without external serial EEPROM. Two analog comparators with programmable reference simplify interface to sensors and analog signals.
Typical applications include appliance control, motor drive interfaces, automotive sub-systems (non-safety), battery chargers, security panels, and low-end consumer white goods where deterministic behavior and OTP cost economics dominate over re-programmability.
When designing with this OTP MCU, plan code volume carefully - OTP parts cannot be re-programmed. Account for oscillator start-up time, configure the brown-out reset threshold to match VDD, and use the EEPROM data memory block for parameter storage to enable post-production tuning without code re-flashes.
This page synthesizes distributor availability, same-brand drop-in alternatives from the PIC16CE62x family, and practical design considerations not consolidated on manufacturer product pages.
ドロップイン代替品: PIC16CE624T-30/SS — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: PIC16CE624T-30/SS （同一形状・フットプリント） — 相違点: Package, Program Memory Size, Core Architecture, Timers, EEPROM Data Memory.
クイック比較ツール — 並列比較する代替部品を選択:
PIC16CE624T-04E/SS
✅ ドロップイン✓ 在庫あり
$2.55 / 個
データシートを見る →PIC16CE624T-04I/SS
✅ ドロップイン✓ 在庫あり
$2.85 / 個
データシートを見る →PIC16CE624T-04/SS
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$4.75 / 個
データシートを見る →PIC16CE623T-04I/SS
✅ ドロップイン✓ 在庫あり
$1.85 / 個
データシートを見る →PIC16CE623T-04E/SS
✅ ドロップイン📋 参考代替品（カタログ未掲載）
PIC16F628A-I/SS
✅ ドロップイン✓ 在庫あり
$1.41 / 個
データシートを見る →PIC16F88-I/SS
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$3.08 / 個
データシートを見る →PIC16CE624T-30/SS 最大定格＆電気的特性
| Program Memory Type | OTP EPROM |
| Program Memory Size | 1.75 KB (1792 words) |
| RAM | 96 bytes |
| EEPROM Data Memory | 128 bytes |
| CPU Core | PIC16 8-bit RISC (Harvard) |
| Instruction Set | 35 single-word instructions (14-bit wide) |
| Maximum CPU Speed | 30 MHz (133 ns instruction cycle, -30 grade) |
| Operating Voltage | 2.5 V to 6.0 V |
| I/O Pins | 13 |
| Analog Comparators | 2 (with programmable voltage reference) |
| Timers | Timer0 (8-bit) + Watchdog Timer with on-chip RC |
| パッケージ | 20-pin SSOP (5.30 mm body) |
| 実装タイプ | Surface Mount |
| 動作温度 | -40C to +85C (industrial) |
| RoHS ステータス | Non-RoHS (legacy OTP family) |
| MSLレベル | 1 (unlimited floor life) |
| Lead-Free | Contains lead (SnPb finish) |
PIC16CE624T-30/SS ピン構成
| ピン 1 | RA2/AN2/VREF — Port A bit 2 / Analog input 2 / Voltage reference output |
| ピン 2 | RA3/AN3/CMP1 — Port A bit 3 / Analog input 3 / Comparator 1 output |
| ピン 3 | RA4/T0CKI — Port A bit 4 / Timer0 clock input (open-drain) |
| ピン 4 | RA5 — Port A bit 5 / Master clear input |
| ピン 5 | VSS — Ground reference |
| ピン 6 | RB0/INT — Port B bit 0 / External interrupt input |
| ピン 7 | RB1 — Port B bit 1 |
| ピン 8 | RB2 — Port B bit 2 |
| ピン 9 | RB3 — Port B bit 3 |
| ピン 10 | RB4 — Port B bit 4 |
| ピン 11 | RB5 — Port B bit 5 |
| ピン 12 | RB6 — Port B bit 6 |
| ピン 13 | RB7 — Port B bit 7 |
| ピン 14 | VDD — Positive supply voltage (2.5V to 6.0V) |
| ピン 15 | OSC2/CLKOUT — Oscillator output / Clock output |
| ピン 16 | OSC1/CLKIN — Oscillator input / External clock input |
| ピン 17 | RA0/AN0 — Port A bit 0 / Analog input 0 |
| ピン 18 | RA1/AN1 — Port A bit 1 / Analog input 1 |
| ピン 19 | RA2 (alt) — Port A bit 2 (alternate function) |
| ピン 20 | RA7 — Port A bit 7 / Not connected (alternate) |
主な用途
PIC16CE624T-30/SS の用途: 7 件s: Appliance Control Panels, Battery Charger Controllers, Security Alarm Panels, Motor Control Interfaces, Industrial Sensor Signal Conditioners, Automotive Sub-System Controllers, White Goods User Interfaces.
Appliance Control Panels
The PIC16CE624T-30/SS fits appliance control panels where fixed-code OTP memory prevents firmware extraction by competitors. Its 1.75 KB program space accommodates washing-machine, dishwasher, and refrigerator user-interface state machines. Two analog comparators on RA0-RA3 interface with line-voltage zero-cross detectors for triac firing, while the programmable voltage reference sets the comparator threshold without external resistor dividers. The 30 MHz CPU clock ensures deterministic 50/60 Hz AC line-cycle timing without jitter. EEPROM data memory stores user presets (cycle selection, temperature, spin speed) through power outages. Brown-out reset handles voltage sag during motor inrush.
おすすめ
Battery Charger Controllers
The PIC16CE624T-30/SS is suitable for lead-acid and NiMH battery charger controllers where the OTP memory locks in charging-algorithm firmware. Two analog comparators monitor charge current (via shunt) and battery voltage, with the programmable voltage reference setting termination thresholds. The 13 I/O pins drive status LEDs, sense temperature thermistors, and switch the charging MOSFET through a gate driver. Watchdog timer prevents firmware lock-up during EMI transients from the switching power stage. Brown-out reset prevents over-discharge of deeply discharged batteries. Industrial -40C to +85C temperature range covers automotive underhood and outdoor solar applications.
おすすめ
Security Alarm Panels
The PIC16CE624T-30/SS provides the central logic for wired security alarm panels in legacy residential and small-commercial installations. Its 13 I/O pins interface with magnetic door/window contacts, PIR motion sensors, smoke detectors, and keypad matrix inputs. The external interrupt (INT) on RB0 wakes the MCU from SLEEP mode on sensor trigger, achieving <1 mA standby current for battery-backed 24-hour operation. EEPROM stores zone configuration and bypass codes that survive power cycles. The OTP memory prevents firmware reverse-engineering by competing alarm installers. Watchdog timer recovers from lockup caused by EMI from lightning-induced transients on long sensor wiring.
おすすめ
Motor Control Interfaces
The PIC16CE624T-30/SS operates as a brushless-DC or stepper-motor interface controller for low-power industrial motion systems. Its 30 MHz CPU clock generates PWM signals with 133 ns resolution for smooth torque control. Two analog comparators on RA0-RA3 sense back-EMF from the motor windings for sensorless commutation. Programmable voltage reference sets over-current trip threshold. 13 I/O pins drive H-bridge gate drivers (IR2104, IRS2003), monitor Hall-effect sensors, and read encoder feedback. Industrial temperature rating and OTP memory suit rugged factory-automation environments where firmware IP protection matters.
おすすめ
Industrial Sensor Signal Conditioners
The PIC16CE624T-30/SS conditions analog sensor signals in industrial measurement systems, leveraging its two analog comparators and programmable voltage reference for threshold detection without external op-amps. The 30 MHz execution speed handles 10-bit-equivalent oversampling for thermocouple, RTD, and strain-gauge linearization. 128 bytes EEPROM stores calibration coefficients per sensor channel, and the 13 I/O pins drive 4-20 mA current loop outputs through a DAC. Industrial temperature range, watchdog timer, and brown-out reset make it suitable for factory-floor deployment.
おすすめ
Automotive Sub-System Controllers
The PIC16CE624T-30/SS handles non-safety automotive sub-systems such as HVAC blend-door actuators, interior lighting controllers, and seat-position memories. Its 2.5-6.0 V operating range covers 5 V regulated vehicle power with load-dump tolerance from external TVS clamps. OTP memory locks in calibration constants and customer-specific feature sets. Two analog comparators monitor back-up battery voltage and motor stall current. EEPROM stores seat-position memory and user preferences. Note: not AEC-Q100 qualified - for safety-critical ECUs use PIC16F1939-I/SS or dsPIC33 variants. Brown-out reset handles cranking voltage dips down to 4 V.
おすすめ
White Goods User Interfaces
The PIC16CE624T-30/SS drives user-interface logic in white goods (microwaves, ovens, washing machines) where fixed-feature sets and low cost dominate. Its 13 I/O pins scan 4x4 keypads, drive 7-segment LED displays, and interface with the main appliance control board via serial link. OTP memory prevents aftermarket firmware modifications that could bypass safety interlocks. EEPROM stores user-set clock time, cooking programs, and language preferences across power cycles. Two analog comparators with programmable voltage reference detect door-open switch position and zero-cross for triac-fired heating elements. Industrial temperature range handles under-cabinet heat-rise.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: PIC16CE624T-30/SS — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | PIC16CE624T-04E/SS | PIC16CE624T-04I/SS | PIC16CE623T-04I/SS | PIC16CE623T-04E/SS | PIC16F628A-I/SS | PIC16F88-I/SS |
|---|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | SSOP-20 | SSOP-20 - same | SSOP-20 - same | SSOP-20 - same | SSOP-20 - same | SSOP-20 - same | SSOP-20 - same |
| Program Memory | 1.75 KB OTP | 1.75 KB OTP - same | 1.75 KB OTP - same | 0.875 KB OTP (-50%) | 0.875 KB OTP (-50%) | 3.5 KB Flash (+100%) | 7.2 KB Flash (+310%) |
| EEPROM Data Memory | 128 bytes | 128 bytes - same | 128 bytes - same | 64 bytes (-50%) | 64 bytes (-50%) | 128 bytes - same | 256 bytes (+100%) |
| Maximum CPU Speed | 30 MHz | 4 MHz (-87%) | 4 MHz (-87%) | 4 MHz (-87%) | 4 MHz (-87%) | 20 MHz (-33%) | 20 MHz (-33%) |
| RAM | 96 bytes | 96 bytes - same | 96 bytes - same | 96 bytes - same | 96 bytes - same | 224 bytes (+133%) | 368 bytes (+283%) |
| Memory Type | OTP EPROM | OTP EPROM - same | OTP EPROM - same | OTP EPROM - same | OTP EPROM - same | Flash (re-programmable) | Flash (re-programmable) |
| RoHS Compliance | Non-RoHS (SnPb) | Non-RoHS | Non-RoHS | Non-RoHS | Non-RoHS | RoHS compliant | RoHS compliant |
| Lifecycle Status | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete | Active | Active |
主な差別化要因
- Fastest speed grade in the PIC16CE62X OTP family （vs PIC16CE624T-04E/SS)
- Largest EEPROM data memory in the OTP PIC16CE62X family （vs PIC16CE623T-04I/SS)
- Compatible with flash-based migration path （vs PIC16F628A-I/SS)
設計ノート
OTP memory cannot be re-programmed - verify the entire firmware image before programming. Any code bug locked into OTP requires scrapping the device. Production programmers must use socketed programming modules rather than in-system programming (ISP). Plan for code-freeze testing on windowed EPROM prototypes (PIC16CE624/JW) before committing to OTP production volume. Allocate the last 16 words of program memory for serial number and configuration tracking per Microchip application note TB075.
Brown-out reset (BOR) configuration bits select between 2.0 V, 3.5 V, 4.0 V, and 4.5 V thresholds. For 5 V systems, set BOR to 4.0 V to ensure clean reset during power sag without false-triggering during normal operation. For 3.3 V systems, use the 2.0 V threshold. SLEEP mode current is typically <1 uA with WDT disabled - use SLEEP between sensor polls to extend battery life. Watchdog timer postscaler can be 1:1 to 1:128 - select to balance lockup recovery vs sleep current overhead.
Place the 20-pin SSOP decoupling capacitor (100 nF ceramic + 10 uF tantalum in parallel) within 5 mm of the VDD pin 14. Route the VDD trace as a 0.5 mm wide power rail directly to the capacitor pad - avoid daisy-chaining from a shared bus. Connect VSS pin 5 to the ground pour with multiple vias. Place the crystal or resonator within 5 mm of OSC1/OSC2 pins 15-16, with short traces and ground shielding on both sides to reduce EMI radiation. Add a 1 M-ohm parallel resistor across the crystal to ensure oscillator startup at low temperatures.
コンプライアンス情報
PIC16CE62X OTP family is legacy with SnPb (tin-lead) finish, predating RoHS. Not AEC-Q100 qualified - migrate to flash-based PIC16F or dsPIC33 AEC-Q100 parts for automotive safety-critical applications. REACH compliant per Microchip material declaration. Lead-free and halogen-free status not verified for this specific OTP part - request Microchip product environmental compliance report.
