PIC16F1716-E/ML - 8-Bit MCU, 14KB Flash, 32MHz, 28-QFN | Microchip
部品番号: PIC16F1716-E/ML ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $2.95 | $2.95 |
| 10 | $2.66 | $26.60 |
| 100 | $2.36 | $236.00 |
| 500 | $2.13 | $1,065.00 |
| 1,000 | $1.95 | $1,950.00 |
PIC16F1716-E/ML 概要
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM), and peripheral interfaces (ADC, timers, communication buses) into one package. Within the broader taxonomy it belongs to the class of embedded controllers, a subset of microprocessors, which are themselves a subset of digital semiconductors. The PIC16F family sits in the 8-bit mid-range category, optimized for low-power and cost-effective general-purpose applications, sitting above PIC10/12 baseline parts and below the PIC18 and PIC32 16/32-bit families.
Key features include eXtreme Low Power (XLP) technology for battery-friendly operation, Peripheral Pin Select (PPS) for flexible signal routing, multiple communication interfaces (I²C, SPI, UART), and enhanced PWM/CCP modules for motor and lighting control. The integrated op amps and DACs enable closed-loop analog control without external components, while CLC/NCO/COG peripherals implement complex logic, frequency synthesis, and waveform generation in hardware without CPU intervention.
The PIC16F1716 architecture is built on an enhanced mid-range 8-bit core with a 14-bit instruction word, a hardware stack, and Harvard bus structure. It supports in-circuit serial programming (ICSP) and in-circuit debugging via ICD, allowing firmware updates after PCB assembly. Internal voltage reference and zero-cross detect support direct mains-coupled signal conditioning.
Typical applications include LED lighting control, battery-powered sensor nodes, consumer appliances, industrial control loops, and small motor drives. The combination of on-chip op amps, DAC, and PWM simplifies mixed-signal designs.
When designing with this MCU, ensure decoupling capacitors (100 nF and 10 µF) are placed close to VDD/AVDD pins, and configure unused I/O as outputs low to minimize current draw. PPS must be remapped before peripheral enable to avoid unintended signal conflicts.
This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet, with values verified against Microchip's official 28-pin PIC® (L)F170x/171x datasheet family.
ドロップイン代替品: PIC16F1716-E/ML — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: PIC16F1716-E/ML （同一形状・フットプリント） — 相違点: Package, ADC, Operating Temperature, Program Memory (Flash), Communication Interfaces.
クイック比較ツール — 並列比較する代替部品を選択:
PIC16F1713-I/ML
✅ ドロップイン📋 参考代替品（カタログ未掲載）
PIC16F1713-E/ML
✅ ドロップイン📋 参考代替品（カタログ未掲載）
PIC16F1707-I/ML
✅ ドロップイン✓ 在庫あり
$0.72 / 個
データシートを見る →PIC16F1613-E/ML
✅ ドロップイン✓ 在庫あり
$0.84 / 個
データシートを見る →PIC16F1615-I/ML
✅ ドロップイン✓ 在庫あり
$0.84 / 個
データシートを見る →PIC16F1705T-I/ML
✅ ドロップイン✓ 在庫あり
$1.22 / 個
データシートを見る →PIC16F1716-E/ML 最大定格＆電気的特性
| Core | PIC16 8-bit enhanced mid-range |
| Program Memory (Flash) | 14 KB (8K x 14 words) |
| Data RAM | 1 KB |
| Maximum CPU Speed | 32 MHz |
| Instruction Word | 14-bit |
| ADC | 10-bit |
| DAC | 5-bit and 8-bit |
| Operational Amplifiers | On-chip |
| Comparators | High-speed comparators |
| PWM/CCP | Enhanced PWM, CCP |
| Communication Interfaces | I²C, SPI, UART |
| Core Independent Peripherals | CLC, COG, NCO, Zero Cross Detect |
| Peripheral Pin Select (PPS) | Yes |
| XLP (eXtreme Low Power) | Yes |
| パッケージ | 28-pin QFN (6x6 mm) |
| 実装タイプ | Surface Mount |
| 動作温度 | -40°C to +125°C (E suffix = extended) |
| RoHS ステータス | Compliant |
PIC16F1716-E/ML ピン構成
| ピン 1 | RA3/AN3/C1IN+/C2IN+/OPA1IN+ — I/O / ADC / comparator / op-amp input |
| ピン 2 | RA4/AN4/C1IN-/OPA1IN-/T0CKI — I/O / ADC / op-amp / Timer0 clock |
| ピン 3 | RA5/AN5/OPA1OUT/DAC5OUT1 — I/O / ADC / op-amp output / DAC output |
| ピン 4 | RA6/OPA2IN+/DAC5OUT2 — I/O / op-amp input / DAC output |
| ピン 5 | RA7/OPA2OUT/DAC5OUT3 — I/O / op-amp output / DAC output |
| ピン 6 | VSS — Ground reference |
| ピン 7 | RA0/AN0/ULPWU/C1IN0-/DAC8OUT — I/O / ADC / ultra-low-power wake-up / DAC output |
| ピン 8 | RA1/AN1/C2IN0-/OPA2IN-/ZCD — I/O / ADC / comparator / zero-cross detect |
| ピン 9 | RA2/AN2/DAC5OUT0 — I/O / ADC / DAC output |
| ピン 10 | RC0/SOSCO/CLKOUT — I/O / secondary oscillator / clock output |
| ピン 11 | RC1/SOSCI — I/O / secondary oscillator input |
| ピン 12 | RC2/AN6/C1IN12-/C2IN12-/OPA3IN+ — I/O / ADC / op-amp input |
| ピン 13 | RC3/AN7/C1IN13-/C2IN13-/OPA3IN-/OPA3OUT — I/O / ADC / op-amp in/out |
| ピン 14 | RC4/AN8/C2OUT/SDA — I/O / ADC / comparator output / I²C data |
| ピン 15 | RC5/AN9/C1OUT/SCL — I/O / ADC / comparator output / I²C clock |
| ピン 16 | RC6/AN10/CCP3/SCK/SCL — I/O / ADC / CCP / SPI clock |
| ピン 17 | RC7/AN11/CCP4/SDI/SDA — I/O / ADC / CCP / SPI data |
| ピン 18 | RB0/AN12/C2IN1+/CCP1 — I/O / ADC / comparator / CCP PWM |
| ピン 19 | RB1/AN10/C1IN3-/CCP2 — I/O / ADC / comparator / CCP PWM |
| ピン 20 | RB2/AN8/PWM4/COG1FLT — I/O / ADC / PWM / COG fault |
| ピン 21 | RB3/AN9/PWM5/COG1OUT — I/O / ADC / PWM / COG output |
| ピン 22 | RB4/AN11/PWM6/COG1IN — I/O / ADC / PWM / COG input |
| ピン 23 | RB5/AN13/CCP5/T1G — I/O / ADC / CCP / Timer1 gate |
| ピン 24 | RB6/ICSPCLK — I/O / ICSP clock / programming |
| ピン 25 | RB7/ICSPDAT — I/O / ICSP data / programming |
| ピン 26 | VDD — Positive supply voltage |
| ピン 27 | AVDD — Analog positive supply voltage |
| ピン 28 | AVSS — Analog ground reference |
主な用途
PIC16F1716-E/ML の用途: 7 件s: LED Lighting Control, Battery-Powered Sensor Nodes, Small BLDC / DC Motor Control, Industrial Control Loops, Consumer Appliance Front Panels, Power Supply Monitoring / Digital Power, Automotive Body Electronics.
LED Lighting Control
The PIC16F1716-E/ML is well-suited for LED lighting drivers because its 14KB Flash and Core Independent Peripherals (CLC, COG, NCO, PWM) implement hardware-based color-mixing, dimming curves, and zero-cross detection without CPU load. The on-chip op amps condition current-sense feedback for closed-loop LED current regulation, while the 32MHz CPU executes DMX-512 or DALI protocol stacks. Peripheral Pin Select (PPS) routes the 10-bit ADC to any I/O for flexible PCB layout. This integration reduces BOM cost by removing external analog front-ends and enables compact, fan-less driver designs for architectural and signage lighting.
おすすめ
Battery-Powered Sensor Nodes
The PIC16F1716-E/ML's eXtreme Low Power (XLP) technology and 32MHz performance make it ideal for battery-powered wireless sensor nodes. The integrated 10-bit ADC and on-chip op amps amplify and digitize thermocouple, strain-gauge, or bridge sensor outputs without external signal conditioning. XLP sleep currents under 1 µA extend coin-cell life to years, while 14KB Flash accommodates BLE/Zigbee stack fragments or LoRaWAN application code. Peripheral Pin Select allows the UART/SPI/I²C to map onto any I/O pin, simplifying PCB routing for compact sensor modules.
おすすめ
Small BLDC / DC Motor Control
The PIC16F1716-E/ML drives small brushless DC or brushed DC motors using its enhanced PWM and CCP modules combined with the on-chip op amps for current sensing. The Complementary Output Generator (COG) generates hardware-dead-band PWM with sub-microsecond resolution, eliminating CPU jitter at 32 kHz PWM frequencies. Zero Cross Detect (ZCD) peripheral enables sensorless BLDC back-EMF zero-crossing detection directly from the motor terminal, while NCO provides high-resolution frequency synthesis for stepper-rate generation. The 1KB RAM supports lookup-table-driven sinusoidal commutation.
おすすめ
Industrial Control Loops
The PIC16F1716-E/ML implements PID-style industrial control loops using its on-chip op amps for analog signal conditioning, 10-bit ADC for feedback sampling, and 5/8-bit DACs for analog setpoint or actuator drive. Hardware CLC modules build latching alarms, fault detectors, and PWM-modulation logic without firmware round-trip latency. UART/SPI/I²C interfaces connect to industrial Modbus RTU slaves or sensor displays. Extended -40°C to +125°C operation (E suffix) suits factory-floor enclosures, while the 28-QFN 6x6 footprint fits compact DIN-rail modules.
おすすめ
Consumer Appliance Front Panels
The PIC16F1716-E/ML powers capacitive-touch and rotary-encoder-based appliance user interfaces using the Zero Cross Detect peripheral for mains-synchronous timing and the 10-bit ADC for knob/button scanning. The on-chip op amps buffer thermistor inputs for over-temperature shutdown, while CLC implements haptic feedback pulse generation in hardware. 14KB Flash hosts multi-language UI strings and EEPROM emulation for user presets. The 28-QFN package keeps the PCB compact behind the front panel, with PPS routing signals to reduce trace congestion.
おすすめ
Power Supply Monitoring / Digital Power
The PIC16F1716-E/ML functions as a digital supervisor in switched-mode power supplies, using its high-speed comparators and on-chip op amps to monitor output voltage and current with sub-microsecond response. The NCO synthesizes programmable-frequency clocks for synchronous rectification timing, while the 10-bit ADC digitizes telemetry for I²C reporting to a host MCU. Core Independent Peripherals implement hardware fault latching (OVP, OCP, OTP) without CPU intervention, improving system reliability. The 32 MHz CPU handles PMBus or proprietary telemetry protocols.
おすすめ
Automotive Body Electronics
The PIC16F1716-E/ML's extended temperature range (-40°C to +125°C, E suffix) and on-chip op amps support automotive body modules such as seat controllers, mirror adjusters, and interior lighting nodes. The 32 MHz CPU processes LIN or CAN-LIN gateway logic, while the 10-bit ADC reads multi-channel sensor inputs. XLP technology keeps quiescent current under automotive key-off budgets. The 28-QFN 6x6 footprint is well-suited for space-constrained ECU housings, and the on-chip DAC generates analog sensor-simulation outputs during end-of-line testing.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: PIC16F1716-E/ML — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | PIC16F1713-I/ML | PIC16F1713-E/ML | PIC16F1707-I/ML | PIC16F1613-E/ML | PIC16F1615-I/ML | PIC16F1705T-I/ML |
|---|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 28-QFN (6x6 mm) | 28-QFN (6x6 mm) - same | 28-QFN (6x6 mm) - same | 28-QFN (6x6 mm) - same | 28-QFN (6x6 mm) - same | 28-QFN (6x6 mm) - same | 28-QFN (6x6 mm) - same |
| Program Memory (Flash) | 14 KB | 7 KB | 7 KB | 3.5 KB | 7 KB | 14 KB | 14 KB |
| Data RAM | 1 KB | 512 B | 512 B | 256 B | 512 B | 1 KB | 1 KB |
| Maximum CPU Speed | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| On-Chip Op Amps | Yes (multiple) | Yes | Yes | Yes | No | No | Yes |
| Core Independent Peripherals (CLC/COG/NCO) | CLC + COG + NCO + ZCD | CLC + COG + NCO + ZCD | CLC + COG + NCO + ZCD | CLC + COG (no NCO) | CLC + NCO (no COG) | CLC + COG + NCO | CLC + COG + NCO + ZCD |
| Peripheral Pin Select (PPS) | Yes | Yes | Yes | Yes | Yes | Yes | Yes |
| Operating Temperature Range | -40°C to +125°C (E suffix) | -40°C to +85°C (I suffix) | -40°C to +125°C (E suffix) | -40°C to +85°C (I suffix) | -40°C to +125°C (E suffix) | -40°C to +85°C (I suffix) | -40°C to +85°C (I suffix) |
主な差別化要因
- Largest Flash memory in the 28-QFN Intelligent Analog family （vs PIC16F1713-I/ML)
- Retains on-chip op amps unlike the F161x cost-down family （vs PIC16F1613-E/ML)
- Full Core Independent Peripherals suite (CLC + COG + NCO + ZCD) （vs PIC16F1707-I/ML)
設計ノート
Place a 100 nF ceramic decoupling capacitor within 3 mm of each VDD/AVDD pin and a 10 µF bulk capacitor at the PCB supply entry. The PIC16F1716-E/ML's AVDD and AVSS pins power the analog peripherals (ADC, DAC, op amps); route them with a separate analog ground island joined to digital ground at a single point under the IC to minimize digital switching noise coupling into analog measurements.
The 28-QFN (6x6 mm) package has an exposed thermal pad on the underside that must be soldered to a PCB land of at least the same size, with thermal vias to an internal ground plane for heat dissipation. Per JEDEC J-STD-020, the package is MSL-1 rated; reflow profile must peak at 260°C for no more than 30 seconds to avoid moisture damage and pad lifting.
Peripheral Pin Select (PPS) registers must be unlocked, configured, and locked BEFORE the corresponding peripheral is enabled; otherwise the peripheral will operate on its default pin and PPS routing will not apply. Unused I/O should be configured as outputs driving low to minimize current draw, especially in XLP sleep modes where floating inputs can leak several µA.
When using the on-chip op amps for high-impedance sensor signal conditioning, route the op-amp output traces away from PWM switching signals and CCP outputs to avoid crosstalk. The DAC outputs are not high-current drivers; buffer them externally if driving low-impedance loads below 5 kΩ. The 10-bit ADC achieves best linearity when source impedance is below 10 kΩ — add an external buffer if the sensor cannot meet this.
Estimated: with 14 KB Flash code typical idle current of 5 mA at 32 MHz and 3.3 V, the 28-QFN package dissipates approximately 16.5 mW. The exposed thermal pad reduces θJA to roughly 30 °C/W (vs 60-70 °C/W without pad soldering), giving a junction temperature rise of <0.5 °C at 25 °C ambient — thermal management is generally not a concern at this power level unless the system is sealed in an enclosure with poor airflow.
コンプライアンス情報
RoHS compliant per Microchip product page. -ML QFN package is Pb-free matte-tin finish, MSL-1 rated per JEDEC J-STD-020. The PIC16F1716 family is not AEC-Q100 qualified; for AEC-Q100 applications, choose the PIC16F1716T-I/ML or PIC16F1716-E/ML industrial-grade variant and verify against Microchip's automotive-grade portfolio.
