PIC16F88T-I/ML - 8-Bit 20MHz Flash MCU | Microchip
部品番号: PIC16F88T-I/ML ✓ 生産中PIC16F88T-I/ML 概要
A PIC16-family microcontroller is an embedded-processing device that combines a RISC-based CPU, program memory, data memory, I/O ports, and dedicated peripherals on one integrated circuit. The PIC16F88 belongs to Microchip's enhanced Flash microcontroller family and uses 35 single-word instructions with a stated 200 ns instruction-execution capability. This architecture is suited to motor-control, instrumentation, communications, and general-purpose embedded products.
Key device characteristics include 8 KB of total Flash capacity as described by the 7 KB programming figure, 4K × 14-word program organization, 368 bytes of RAM, 16 I/O lines, and operation up to 20 MHz. These resources allow a single device to handle digital I/O, timed control sequences, serial data, and analog monitoring functions. The -40 °C to +85 °C temperature range is associated with the related PIC16F88-I/ML ordering code and must be confirmed for the exact target before qualification.
The T designation identifies the temperature-grade version within the PIC16F88 ordering system, while /ML denotes the QFN package used by the target device. Microchip also offers the PIC16F88 in an 18-pin package, as stated on the manufacturer product page, but that configuration is not interchangeable with the 28-pin QFN footprint. Firmware development is therefore performed around the 28-pin pin assignment while retaining the familiar PIC16 instruction set.
Typical applications include small motor controllers, digital thermometers and environmental monitors, sensor acquisition nodes, programmable LED drivers, compact power-control modules, and industrial interface boards. The combination of 20 MHz processing speed, Flash memory, RAM, and 16 I/O pins lets one controller coordinate several peripheral functions without requiring a separate processor.
PCB design must account for the exposed-pad and thermal characteristics of the QFN package, adequate decoupling near the supply pins, and clean return paths for sensitive analog inputs. Confirm oscillator, I/O, programming, and power-pin assignments against the manufacturer pin-description table before routing the PCB. Do not substitute the 18-pin or SOIC package without changing the land pattern and firmware-dependent board configuration.
This product record combines the exact ordering information, memory organization, package dimensions, clock rating, and practical replacement guidance for PIC16F88T-I/ML. The comparison also highlights package constraints, programming-interface considerations, and the verification steps needed when replacing an existing PIC16F88 design without introducing board-level incompatibilities.
ドロップイン代替品: PIC16F88T-I/ML — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: PIC16F88T-I/ML (同一形状・フットプリント) — 相違点: Package, I/O Pins, RoHS Status, ADC, Communication.
PIC16F88-I/ML
✅ ドロップイン価格はお問い合わせください
データシートを見る →PIC16F887T-I/ML
✅ ドロップイン価格はお問い合わせください
データシートを見る →PIC16F884T-I/ML
✅ ドロップイン価格はお問い合わせください
データシートを見る →PIC16F88T-I/ML 最大定格&電気的特性
| Microcontroller Type | 8-bit PIC microcontroller |
| 最大クロック周波数 | 20 MHz |
| Instruction Execution Time | 200 ns |
| Instruction Set | 35 single-word instructions |
| Program Memory | 7 KB Flash organized as 4K × 14 words |
| RAM | 368 bytes |
| I/O Pins | 16 |
| パッケージ | 28-pin QFN, 6 × 6 mm |
| 実装タイプ | Surface mount |
| Core Architecture | Enhanced-Flash PIC architecture |
| Programming Memory Type | Flash |
| Related Industrial Temperature Range | -40 °C to +85 °C |
| Manufacturer Product Family | PIC16F88 18/20/28-pin enhanced Flash microcontroller family |
| RoHS ステータス | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
PIC16F88T-I/ML 28-pin qfn, 6 × 6 mm ピン配置ガイド
PIC16F88T-I/ML (28-pin qfn, 6 × 6 mm パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: PIC16F88T-I/ML.
詳細は データシート をご参照ください。
主な用途
PIC16F88T-I/ML の用途: 6 件s: Compact Motor Controller, Environmental Sensor Node, Programmable LED Driver, Industrial Interface Module, Temperature and Process Monitor, Battery-Powered Instrument.
Compact Motor Controller
The PIC16F88T-I/ML fits compact motor-control and sequencing designs because its 20 MHz 8-bit core provides faster instruction execution than many lower-clock embedded controllers, while 368 bytes of RAM supports state variables and 16 I/O pins provide control and status connections. The device can coordinate timers, digital feedback, and protection inputs for a small stepper, solenoid, or fan assembly. Designers should confirm the required PWM, timer, capture, comparator, and interrupt resources in the manufacturer datasheet. Keep motor-current switching away from sensitive logic traces, and provide external driver, flyback, and overcurrent protection because the microcontroller does not directly replace those power-stage functions.
おすすめ
Environmental Sensor Node
PIC16F88T-I/ML is appropriate for a compact environmental sensor node that combines digital sensing, timed sampling, status indication, and serial reporting. Its 7 KB Flash program memory is sufficient for a focused acquisition and communication routine, while 16 I/O pins allow sensor-enable lines, alarm outputs, and a serial interface to share one controller. Use the ADC or comparator resources only after checking their availability and channel assignment for the 28-pin QFN configuration. Keep sensor excitation and analog traces away from switching nodes, establish a defined grounding strategy, and calibrate measurements against the device's operating-temperature limits.
おすすめ
Programmable LED Driver
The 20 MHz PIC16F88T-I/ML can manage programmable LED sequences, dimming, and status patterns in industrial or commercial panels where 16 I/O pins reduce the need for additional logic. Flash memory supports fixed lighting tables or compact update logic, and the microcontroller can implement timers for fading and fault blinking. Confirm the available PWM outputs and compare the LED supply voltage with the MCU's electrical limits; the PIC should normally drive logic-level transistor or LED-driver circuits rather than load a lighting rail directly. Use current-limiting resistors or constant-current drivers and place switched-current paths to minimize coupling into the MCU's supply and control traces.
おすすめ
Industrial Interface Module
PIC16F88T-I/ML suits small industrial interface modules that translate switches, discrete sensors, and field-level signals into a digital communication stream. Its 16 I/O pins provide practical digital-channel capacity, while 7 KB of Flash and 368 bytes of RAM are adequate for protocol handling, debounce state, diagnostics, and configuration storage. Validate the selected peripheral, interrupt vectors, and pin multiplexing against the exact 28-pin QFN ordering code. For longer field cables, use protection networks and isolation at the interface boundary, keep external transients away from the MCU pins, and provide a robust common-mode strategy for reliable operation outside the bench environment.
おすすめ
Temperature and Process Monitor
PIC16F88T-I/ML can support a temperature or general process-monitoring product that periodically samples an analog signal, applies thresholds, drives local indicators, and reports status. The 20 MHz operating rate provides adequate headroom for scheduling, filtering, debounce, and communication tasks, while 16 I/O pins allow inputs and alarms to be distributed around the board. Confirm the ADC, comparator, timer, and reference requirements in the manufacturer documentation before finalizing the design. Place analog inputs away from digital outputs and switching regulators, sample only after the input network has settled, and recalibrate at the product's required temperature range.
おすすめ
Battery-Powered Instrument
The PIC16F88T-I/ML is suitable for a small battery-powered instrument requiring local measurement, user input, and low-power standby behavior. Its Flash program memory supports firmware without external program storage, and the 16 I/O pins can support a display, buttons, alarm output, and status indicators. Power-consumption performance depends on the selected clock, peripheral configuration, sleep mode, and operating temperature, so calculate the duty cycle from the complete system rather than the CPU frequency alone. Use the manufacturer's sleep and peripheral-disable procedures, remove unnecessary external loads during standby, and account for battery self-discharge and regulator dropout in the power-budget calculation.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: PIC16F88T-I/ML — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | PIC16F88-I/ML | PIC16F887T-I/ML | PIC16F884T-I/ML |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 28-pin QFN (6 × 6 mm) | 28-pin QFN (6 × 6 mm) | 28-pin QFN (6 × 6 mm) | 28-pin QFN (6 × 6 mm) |
| Microcontroller Architecture | 8-bit PIC enhanced-Flash architecture | 8-bit PIC enhanced-Flash architecture | 8-bit PIC architecture | 8-bit PIC architecture |
| Temperature Grade | T ordering code; exact range requires confirmation | Non-T ordering code; exact range requires confirmation | T ordering code; exact range requires confirmation | T ordering code; exact range requires confirmation |
主な差別化要因
- Closest direct package-ordering match (vs PIC16F88-I/ML)
- Established PIC16F88 firmware target (vs PIC16F887T-I/ML)
- Direct 16-channel digital I/O allocation (vs PIC16F884T-I/ML)
設計ノート
Use the manufacturer drawing for the 28-pin QFN land pattern, including the exposed pad, pad dimensions, solder-mask opening, and paste pattern. Place the device's required bypass capacitors adjacent to the supply and ground connections, with short, low-impedance paths. A typical 6 × 6 mm QFN package has fine-pitch pads on all four sides, so inspect the assembled board for bridging and verify annular rings after the board rules are finalized.
Keep oscillator components and their return path compact, and route oscillator signals away from switching nodes and high-current digital outputs. For analog measurements, use a quiet ground reference and separate analog and digital return paths where the board architecture permits it. Place programming or test contacts so an in-circuit programmer can reach the required interface without removing nearby components.
Do not treat the 18-pin PIC16F88, SOIC package, and 28-pin QFN version as interchangeable. The target is the /ML QFN ordering code, and its exposed-pad and pin arrangement must match the PCB. Likewise, do not assume that a related PIC16F88 or PIC16F88x device is firmware-compatible merely because the family name is similar. Review the manufacturer ordering table, pin-description table, and pin-and-code compatibility chart before approving a substitution.
Design the supply and decoupling around the manufacturer's electrical-characteristics limits and the highest operating clock. The 20 MHz CPU rating does not determine supply current by itself; current also depends on the selected oscillator, active peripherals, I/O loading, and operating voltage. Verify brownout, input-voltage, and output-pin limits during power-up and shutdown, and prevent externally powered peripherals from back-feeding I/O pins through protection diodes.
コンプライアンス情報
The available manufacturer and distributor information does not state a component-level RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration for the exact ordering code.