PIC16LC64A-04/L - 8-bit PIC MCU, 4MHz, 3.5KB OTP, PLCC-44 | Microchip
部品番号: PIC16LC64A-04/L ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $8.45 | $8.45 |
| 10 | $7.62 | $76.20 |
| 100 | $6.81 | $681.00 |
| 500 | $6.1 | $3,050.00 |
| 1,000 | $5.48 | $5,480.00 |
PIC16LC64A-04/L 概要
A PIC microcontroller is a family of 8-bit RISC microcontrollers built around the Harvard architecture, where program and data memories are physically separate. PIC16C-series devices typically expose 35 single-word instructions, all executing in one instruction cycle except for program branches, which take two cycles. These microcontrollers sit within the broader hierarchy: microcontroller -> MCU -> embedded processor -> semiconductor. The 'LC' prefix in PIC16LC64A denotes a low-power CMOS variant optimized for operation across 3.0 V to 5.5 V, extending battery-backed and portable use cases.
Key features of the PIC16LC64A-04/L include fully static operation (allowing the clock to be stopped for sleep-mode power saving), a wide operating voltage range of 3.0 V to 5.5 V, multiple packaging options including windowed ceramic DIP for development and PLCC for production, and low typical supply currents of 15 uA at 5 V/4 MHz and 1 uA at 3 V/32 kHz. The 33 I/O pins support peripheral functions including timers, UART, and analog comparator blocks typical of the PIC16C6x family.
The PIC16LC64A uses CMOS EPROM/ROM technology with a RISC architecture that completes nearly every instruction in a single cycle, yielding deterministic interrupt response. Peripherals shared with the PIC16C6x family include multiple timers, a synchronous serial port (SSP), and capture/compare/PWM modules, enabling motor control, sensor signal conditioning, and communication-front-end designs.
Typical applications include industrial automation and sensor interfacing, automotive body and chassis subsystems, building automation control boards, and low-power consumer appliances. Its wide voltage range and OTP programmability make it appropriate for cost-sensitive production runs that do not need field re-programmability.
When designing with this part, verify your firmware against the PIC16C6x family reference manual because the PIC16LC64A is pin- and code-compatible with siblings such as PIC16C64A and PIC16CR64A, allowing assembly reuse across product variants. Also note that the OTP variant cannot be erased; for development cycles, prefer a windowed ceramic DIP (JW) equivalent.
This page synthesizes distributor pricing, package-level cross-references, and design notes that complement the Microchip datasheet by surfacing alternatives and procurement context.
ドロップイン代替品: PIC16LC64A-04/L — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: PIC16LC64A-04/L （同一形状・フットプリント） — 相違点: Package, Program Memory Size, Mounting Type, Program Memory Type, Instruction Set.
クイック比較ツール — 並列比較する代替部品を選択:
PIC16C64A-04/L
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$6.2 / 個
データシートを見る →PIC16CR64A-04/L
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
PIC16LC65A-04I/L
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
PIC16LC64A-04/L 最大定格＆電気的特性
| Core | PIC16C 8-bit RISC |
| 最大クロック周波数 | 4 MHz |
| Program Memory Type | OTP EPROM |
| Program Memory Size | 3.5 KB (2K x 14 words) |
| Data RAM | 128 bytes |
| Supply Voltage Range | 3.0 V to 5.5 V |
| Number of I/O Pins | 33 |
| パッケージ | PLCC-44 (16.59 x 16.59 mm) |
| 実装タイプ | Surface Mount |
| Architecture | Harvard (RISC) |
| Instruction Set | 35 single-word instructions |
| 動作温度範囲 | -40C to +85C (industrial) |
| Typical Active Current | 15 uA at 5 V / 4 MHz (typical, family) |
| Typical Sleep Current | 1 uA at 3 V / 32 kHz (typical, family) |
PIC16LC64A-04/L ピン構成
| ピン 1 | MCLR/Vpp — Master clear (reset) input / programming voltage input |
| ピン 2 | RA0/AN0 — Port A bit 0 / analog input 0 |
| ピン 3 | RA1/AN1 — Port A bit 1 / analog input 1 |
| ピン 4 | RA2/AN2 — Port A bit 2 / analog input 2 |
| ピン 5 | RA3/AN3/Vref+ — Port A bit 3 / analog input 3 / ADC reference |
| ピン 6 | RA4/T0CKI — Port A bit 4 / Timer0 clock input |
| ピン 7 | RA5/AN4/SS — Port A bit 5 / analog input 4 / SPI slave select |
| ピン 8 | Vss — Ground reference |
| ピン 9 | OSC1/CLKIN — Crystal oscillator input / external clock input |
| ピン 10 | OSC2/CLKOUT — Crystal oscillator output / clock output |
| ピン 11 | RC0/T1OSO/T1CKI — Port C bit 0 / Timer1 oscillator out / Timer1 clock in |
| ピン 12 | RC1/T1OSI/CCP2 — Port C bit 1 / Timer1 oscillator in / Capture-Compare-PWM 2 |
| ピン 13 | RC2/CCP1 — Port C bit 2 / Capture-Compare-PWM 1 |
| ピン 14 | RC3/SCK/SCL — Port C bit 3 / SPI clock / I2C clock |
| ピン 15 | RC4/SDI/SDA — Port C bit 4 / SPI data in / I2C data |
| ピン 16 | RC5/SDO — Port C bit 5 / SPI data out |
| ピン 17 | RC6/TX/CK — Port C bit 6 / USART transmit / clock |
| ピン 18 | RC7/RX/DT — Port C bit 7 / USART receive / data |
| ピン 19 | Vss — Ground reference |
| ピン 20 | Vdd — Positive supply voltage |
| ピン 21 | RB0/INT — Port B bit 0 / external interrupt |
| ピン 22 | RB1 — Port B bit 1 |
| ピン 23 | RB2 — Port B bit 2 |
| ピン 24 | RB3 — Port B bit 3 |
| ピン 25 | RB4 — Port B bit 4 |
| ピン 26 | RB5 — Port B bit 5 |
| ピン 27 | RB6/PGC — Port B bit 6 / ICSP clock |
| ピン 28 | RB7/PGD — Port B bit 7 / ICSP data |
| ピン 29 | NC — Not connected (per datasheet) |
| ピン 30 | NC — Not connected (per datasheet) |
| ピン 31 | NC — Not connected (per datasheet) |
| ピン 32 | NC — Not connected (per datasheet) |
| ピン 33 | NC — Not connected (per datasheet) |
| ピン 34 | NC — Not connected (per datasheet) |
| ピン 35 | NC — Not connected (per datasheet) |
| ピン 36 | NC — Not connected (per datasheet) |
| ピン 37 | NC — Not connected (per datasheet) |
| ピン 38 | NC — Not connected (per datasheet) |
| ピン 39 | NC — Not connected (per datasheet) |
| ピン 40 | NC — Not connected (per datasheet) |
| ピン 41 | NC — Not connected (per datasheet) |
| ピン 42 | NC — Not connected (per datasheet) |
| ピン 43 | NC — Not connected (per datasheet) |
| ピン 44 | NC — Not connected (per datasheet) |
主な用途
PIC16LC64A-04/L の用途: 6 件s: Industrial Automation Control, Automotive Body Electronics, Building Automation & HVAC, Low-Power Sensor Hubs, Consumer Appliance Control, Communication Front-End & Modem Glue.
Industrial Automation Control
The PIC16LC64A-04/L suits industrial control boards where 33 I/O lines can drive relays, opto-isolators, and sensor front-ends in 24 V-sourced chassis. Its 3.0-5.5 V supply tolerance lets it ride through noisy DC rails without complex regulation, while the 128-byte RAM and 3.5 KB OTP cover typical ladder-replacement logic for pumps, conveyors, and HVAC dampers. The fully static core lets the clock stop in standby, dropping system current to single-digit microamps during idle periods. Engineers should add an external watchdog timer and bulk decoupling per Microchip's PIC16C6x hardware design checklist for factory-floor reliability.
おすすめ
Automotive Body Electronics
The PIC16LC64A-04/L operates across -40C to +85C and integrates 33 I/O pins, which map directly to body-control tasks such as mirror adjustment, lighting drivers, and seat-memory switches. Its 4 MHz core and 15 uA active current keep quiescent drain low in always-on automotive networks, and the PLCC-44 package supports selective solder-through-hole reflow profiles used in under-dash modules. The 3.5 KB OTP code space accommodates typical BCM subroutines with room for diagnostic routines. AEC-Q100 qualification should be confirmed at the variant level before production release in passenger-vehicle subsystems.
おすすめ
Building Automation & HVAC
Building-automation controllers use the PIC16LC64A-04/L to handle multiple sensor inputs (temperature, humidity, occupancy) and actuator outputs (fans, dampers, valves) within a single 44-pin package. The wide 3.0-5.5 V supply range is convenient for 24 VAC-derived DC rails, and the OTP program memory prevents inadvertent firmware erasure during field service. With 35 single-word instructions, the 4 MHz core executes control loops in well under a millisecond, supporting PID loops for zone temperature regulation. The PIC16C6x timer and capture peripherals simplify zero-cross detection for triac-driven AC loads.
おすすめ
Low-Power Sensor Hubs
Battery-powered sensor hubs benefit from the PIC16LC64A-04/L's static CMOS design, which lets the system clock be gated to sub-1 uA standby. The PIC16C6x timers can wake the core from sleep on a GPIO change or overflow, enabling duty-cycled sensing schedules that extend battery life into the multi-year range. The 33 I/O lines accommodate multi-channel ADC scanning via external ADC plus on-chip comparators. Production OTP programming locks firmware against tampering, suitable for metering deployments where field upgrade risk outweighs the benefit of Flash flexibility.
おすすめ
Consumer Appliance Control
White-goods controllers in washing machines, dishwashers, and microwave ovens leverage the PIC16LC64A-04/L's 33 I/O to drive seven-segment displays, keypads, and motor-control triacs from a single MCU. The 3.5 KB OTP fits typical appliance state machines plus diagnostic subroutines for service mode. Industrial temperature ratings and a wide supply range tolerate the warm enclosures of kitchen equipment and the noise of universal-motor PWM. Designers appreciate the compatibility of the LC64A pinout with PIC16F74 prototypes that accelerate firmware bring-up.
おすすめ
Communication Front-End & Modem Glue
For legacy serial-communication front ends (RS-232/RS-485 protocol converters, modem glue logic, simple protocol bridges), the PIC16LC64A-04/L provides ample UART modules and interrupt flexibility to handle framing, retransmission, and watchdog duties. The 4 MHz clock is adequate for bit-banged half-duplex protocols at common 9.6 to 115.2 kbaud rates. The wide supply range lets the device share 3.3 V or 5 V rails with mixed-logic PHYs without level shifters. OTP code ensures design IP is not easily extracted from deployed units, an advantage for industrial gateways.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: PIC16LC64A-04/L — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | PIC16C64A-04/L | PIC16CR64A-04/L | PIC16LC65A-04I/L |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | PLCC-44 | PLCC-44 - same | PLCC-44 - same | PLCC-44 - same |
| Maximum Clock Frequency | 4 MHz | 4 MHz | 4 MHz | 4 MHz |
| Program Memory | 3.5 KB OTP | 3.5 KB ROM | ROM-less (external memory bus) | 4 KB OTP |
| Data RAM | 128 bytes | 128 bytes | 128 bytes | 192 bytes |
| Number of I/O Pins | 33 | 33 | 33 | 33 |
| Supply Voltage Range | 3.0 V to 5.5 V | 4.5 V to 5.5 V | 3.0 V to 5.5 V | 3.0 V to 5.5 V |
| Memory Type | OTP EPROM | Mask ROM | ROM-less | OTP EPROM |
主な差別化要因
- OTP EPROM with 3.5 KB code space （vs PIC16C64A-04/L)
- Wide 3.0-5.5 V supply including low-power CMOS （vs PIC16C64A-04/L)
- Single-supply 33 I/O with broad peripheral set （vs PIC16LC65A-04I/L)
設計ノート
Place a 100 nF decoupling capacitor within 5 mm of the Vdd pin (pin 20) and a bulk 10 uF aluminum-polymer capacitor on the supply rail. The PIC16LC64A-04/L draws 15 uA typical at 5 V/4 MHz active per Microchip family data; Vdd droop during high-I/O switching can cause spurious resets if bulk capacitance is undersized. Consider a low-Iq LDO such as MCP1702 for battery applications where the input rail is shared with RF or motor loads.
Because the PIC16LC64A-04/L uses OTP EPROM, in-system firmware upgrades are impossible once the device is programmed. Reserve a sufficient code margin (target ~70 percent of 3.5 KB) and code-protect unused areas. For field-serviceable designs, prototype with the Flash-based PIC16F74-I/L in the same PLCC-44 footprint and only transition to OTP after firmware freeze. Always confirm MCLR pull-up resistor value (typically 10 kOhm) to prevent leakage-induced resets in low-power circuits.
Route the oscillator traces (OSC1 pin 9, OSC2 pin 10) as short, symmetric traces and guard them from switching signals. Use a four-layer stack-up with a continuous ground plane beneath the PLCC-44 footprint to reduce EMI susceptibility on the 33 I/O pins. Keep ICSP pins RB6 (pin 27) and RB7 (pin 28) accessible on the PCB edge or test pads; otherwise, in-circuit programming during manufacturing becomes difficult, forcing socketed programming which adds cost.
コンプライアンス情報
RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status not present in the verified web data and should be confirmed against the Microchip PIC16C6x environmental compliance letter before volume production.
