PIC18F2585-H/SP - 48KB Flash 8-bit MCU w/ECAN, 25MHz, SPDIP-28 | Microchip
部品番号: PIC18F2585-H/SP ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $8.42 | $8.42 |
| 10 | $7.58 | $75.80 |
| 100 | $6.74 | $674.00 |
| 500 | $6.05 | $3,025.00 |
| 1,000 | $5.38 | $5,380.00 |
PIC18F2585-H/SP 概要
An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path that integrates a CPU core, program memory (flash/ROM), data RAM, peripherals (timers, ADC, communication controllers), and I/O pins. PIC18F devices use Microchip's enhanced Harvard RISC architecture with a 16-bit instruction word and 8-bit data path, reaching up to 10 MIPS at 40 MHz. Within the power management and embedded hierarchy, MCUs sit below microprocessors and above digital signal controllers in capability; the PIC18 family specifically spans the 28- to 80-pin range with CAN, USB, and Ethernet connectivity options.
Key features include a 25 MHz maximum operating frequency (10 MIPS instruction rate), an internal oscillator, an integrated 10-bit analog-to-digital converter with up to 8 input channels, a CAN 2.0B active controller, nanoWatt power management for low-power sleep modes, and an Enhanced Capture/Compare/PWM (ECCP) module. The part also offers 25 digital I/O pins, two USART modules, MSSP (SPI/I2C), and 1 KB of data EEPROM. The 48 KB flash provides comfortable headroom for CAN stacks plus application firmware.
Architecture-wise, the PIC18F2585 uses a 16-bit instruction word with a two-stage pipeline, hardware multiply, and C-friendly register set. The integrated ECAN module is fully CAN 2.0B active compliant with hardware acceptance filters, supporting baud rates up to 1 Mbps. Combined with 8-channel 10-bit ADC and nanoWatt technology, this device is designed for sensor-heavy automotive nodes.
Typical applications include automotive body and chassis ECUs, industrial CAN nodes, sensor aggregation gateways, HVAC controllers, and high-temperature under-hood or industrial automation equipment. The H temperature grade and ECAN make it a strong fit for OBD-II peripherals and CAN-based sensor clusters.
When designing with this device, ensure the CAN bus is terminated per ISO 11898 with 120 ohm resistors at each end and that the ECAN bit timing is configured per the CiA-recommended oscillator error calculation. Programming is supported via ICSP and the MPLAB ICD 5 debugger.
This page synthesizes distributor pricing, drop-in alternatives, and design notes not found in the manufacturer datasheet alone.
ドロップイン代替品: PIC18F2585-H/SP — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: PIC18F2585-H/SP （同一形状・フットプリント） — 相違点: MSL Level, RoHS Status, Timers, Operating Temperature Range, ADC.
クイック比較ツール — 並列比較する代替部品を選択:
PIC18F2585-I/SP
✅ ドロップイン✓ 在庫あり
$5.95 / 個
データシートを見る →PIC18F2585-E/SP
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$5.02 / 個
データシートを見る →PIC18F2580-I/SP
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$4.55 / 個
データシートを見る →PIC18F2685-I/SP
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
PIC18F2480-I/SP
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$4.1 / 個
データシートを見る →PIC18F2585-H/SP 最大定格＆電気的特性
| Program Memory Size | 48 KB (24K x 16) Flash |
| RAM Size | 3.25 KB (3328 bytes) |
| Data EEPROM | 1 KB |
| CPU Core | PIC18 8-bit RISC (Harvard) |
| 最大クロック周波数 | 25 MHz (10 MIPS) |
| Operating Voltage Range | 2.0 V to 5.5 V |
| 動作温度範囲 | -40C to +150C (H temp grade) |
| Number of I/O Pins | 25 |
| ADC | 10-bit, up to 8 channels |
| CAN Module | ECAN 2.0B active, 1 controller |
| USART | 2 modules |
| MSSP (SPI/I2C) | 1 module (SPI or I2C) |
| Timers | 4 (Timer0/1/2/3) |
| CCP/ECCP Modules | 2 CCP + 1 ECCP |
| パッケージ | 28-pin SPDIP (0.300 inch, 7.62 mm) |
| 実装タイプ | Through-Hole (DIP) |
| ICSP (In-Circuit Serial Programming) | Yes |
| RoHS ステータス | Compliant |
| Lead-Free | Yes |
| MSLレベル | 1 (unlimited floor life) |
PIC18F2585-H/SP ピン構成
| ピン 1 | MCLR/RA5 — Master Clear (reset) input / digital I/O |
| ピン 2 | RA0/AN0 — Digital I/O / analog input channel 0 |
| ピン 3 | RA1/AN1 — Digital I/O / analog input channel 1 |
| ピン 4 | RA2/AN2/VREF- — Digital I/O / analog input 2 / ADC negative reference |
| ピン 5 | RA3/AN3/VREF+ — Digital I/O / analog input 3 / ADC positive reference |
| ピン 6 | RA4/T0CKI — Digital I/O / Timer0 clock input |
| ピン 7 | VSS — Ground reference |
| ピン 8 | VSS — Ground reference |
| ピン 9 | OSC1/CLKI/RA7 — Crystal oscillator input / external clock in / I/O |
| ピン 10 | OSC2/CLKO/RA6 — Crystal oscillator output / clock out / I/O |
| ピン 11 | RC0/T1OSO/T1CKI — Digital I/O / Timer1 oscillator output / Timer1 clock input |
| ピン 12 | RC1/T1OSI/CCP2 — Digital I/O / Timer1 oscillator input / CCP2 |
| ピン 13 | RC2/CCP1 — Digital I/O / Capture Compare PWM 1 |
| ピン 14 | RC3/SCK/SCL — Digital I/O / SPI clock / I2C clock |
| ピン 15 | RC4/SDI/SDA — Digital I/O / SPI data in / I2C data |
| ピン 16 | RC5/SDO — Digital I/O / SPI data out |
| ピン 17 | RC6/TX/CK — Digital I/O / USART TX / USART synchronous clock |
| ピン 18 | RC7/RX/DT — Digital I/O / USART RX / USART synchronous data |
| ピン 19 | VSS — Ground reference |
| ピン 20 | VDD — Positive supply voltage (2.0V to 5.5V) |
| ピン 21 | RB0/INT0 — Digital I/O / external interrupt 0 |
| ピン 22 | RB1/INT1 — Digital I/O / external interrupt 1 |
| ピン 23 | RB2/INT2 — Digital I/O / external interrupt 2 |
| ピン 24 | RB3/INT3/CCP2 — Digital I/O / external interrupt 3 / CCP2 alternate |
| ピン 25 | RB4 — Digital I/O / interrupt-on-change |
| ピン 26 | RB5/PGM — Digital I/O / LVP programming |
| ピン 27 | RB6/PGC — Digital I/O / ICSP clock |
| ピン 28 | RB7/PGD — Digital I/O / ICSP data |
主な用途
PIC18F2585-H/SP の用途: 6 件s: Automotive CAN Body Control Modules, Industrial CAN Sensor Nodes, HVAC Climate Control ECUs, Battery Management Slave Modules, CAN-Based Security & Access Panels, Industrial Automation Sensor Aggregators.
Automotive CAN Body Control Modules
The PIC18F2585-H/SP fits automotive body control modules because its integrated ECAN 2.0B active controller handles CAN 2.0B communication at up to 1 Mbps, eliminating an external CAN transceiver controller. With 48 KB flash and 3.25 KB RAM, the device comfortably hosts an OBD-II compatible CAN stack plus body-control firmware. The H temperature grade (-40C to +150C) covers under-dash and most engine-compartment conditions. Use it between the 12V automotive rail and the CAN bus with an external MCP2551 or TJA1050 transceiver; the ECAN hardware filters offload the CPU from bus traffic.
おすすめ
Industrial CAN Sensor Nodes
The PIC18F2585-H/SP is well suited for industrial CANopen or DeviceNet sensor nodes where its 8-channel 10-bit ADC and integrated ECAN together let one chip digitize sensors and publish them onto a CAN bus. The H temperature grade tolerates factory-floor heat near motors or ovens. The 25 MHz clock (10 MIPS) is sufficient for 100 Hz control loops with CAN traffic. Place 120 ohm termination resistors at each bus end per ISO 11898, and use shielded twisted pair for long cable runs.
おすすめ
HVAC Climate Control ECUs
The PIC18F2585-H/SP fits automotive and building HVAC climate control ECUs because its 8-channel 10-bit ADC reads multiple temperature sensors, while the ECAN module reports setpoints and status to a central body controller. The 2.0V to 5.5V supply range tolerates 12V automotive rails when paired with a regulator. The H temperature grade allows placement near heater cores or in plenum cavities. Use PWM on the ECCP module to drive blower motor control FETs.
おすすめ
Battery Management Slave Modules
The PIC18F2585-H/SP serves as a battery-management slave module in distributed Li-ion or lead-acid packs because its 8-channel ADC monitors cell voltages and the ECAN module reports the data over the battery CAN bus. The 1 KB data EEPROM stores calibration coefficients and cycle counters without external storage. The H grade tolerates under-hood or in-pack temperatures. Decouple VDD with 100 nF plus 10 uF bulk and use a precision voltage reference for ADC accuracy.
おすすめ
CAN-Based Security & Access Panels
The PIC18F2585-H/SP integrates well into CAN-based security panels, keyless entry modules, and access control nodes that need both ADC for tamper sensing and CAN for inter-panel communication. The 48 KB flash supports encrypted authentication firmware, and the 3.25 KB RAM handles small message buffers. The H grade suits outdoor or rooftop installations. Use the MSSP peripheral to drive a secure SPI EEPROM for key storage alongside the CAN bus interface.
おすすめ
Industrial Automation Sensor Aggregators
The PIC18F2585-H/SP aggregates multiple sensor inputs onto a single CAN node in industrial automation, replacing discrete I/O modules. Its 25 I/O pins and 8-channel ADC handle several analog sensors plus digital I/O simultaneously, while the ECAN module publishes aggregated data at standard 250 kbps or 500 kbps. The H grade tolerates cabinet temperatures up to 150C. Combine with opto-isolated digital inputs and the internal USART for RS-485 bridging where needed.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: PIC18F2585-H/SP — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | PIC18F2585-I/SP | PIC18F2585-E/SP | PIC18F2580-I/SP | PIC18F2685-I/SP | PIC18F2480-I/SP |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 28-pin SPDIP (0.300 inch) | 28-pin SPDIP - same | 28-pin SPDIP - same | 28-pin SPDIP - same | 28-pin SPDIP - same | 28-pin SPDIP - same |
| Program Flash | 48 KB | 48 KB | 48 KB | 24 KB (-50%) | 96 KB (+100%) | 16 KB (-67%) |
| RAM | 3.25 KB | 3.25 KB | 3.25 KB | 1.5 KB (-54%) | 3.25 KB | 768 B (-77%) |
| Max Clock | 25 MHz (10 MIPS) | 25 MHz | 25 MHz | 25 MHz | 25 MHz | 25 MHz |
| ECAN Module | Yes (CAN 2.0B active) | Yes | Yes | Yes | Yes | No |
| Temperature Grade | H: -40C to +150C | I: -40C to +85C | E: -40C to +125C | I: -40C to +85C | I: -40C to +85C | I: -40C to +85C |
| 10-bit ADC Channels | 8 channels | 8 | 8 | 8 | 8 | 8 |
主な差別化要因
- Extended -40C to +150C H temperature grade （vs PIC18F2585-I/SP)
- Integrated hardware ECAN with hardware acceptance filters （vs PIC18F2480-I/SP)
- Doubled flash and RAM versus PIC18F2580 （vs PIC18F2580-I/SP)
設計ノート
Estimated: At VDD=5.0V, VSS=0V, and 25 MHz active, the PIC18F2585-H/SP core draws roughly 12-16 mA; in Sleep mode it falls below 1 uA thanks to nanoWatt technology. Decouple VDD (pin 20) with a 100 nF ceramic placed within 5 mm of the pin plus a 10 uF bulk near the regulator. Place a ferrite bead on AVDD if you isolate the analog supply, since the ADC reference shares pin 5 (VREF+).
ECAN requires precise oscillator accuracy to meet CAN bit timing requirements. Estimate: a 25 MHz crystal with 30 ppm tolerance is acceptable up to 500 kbps bus speed; for 1 Mbps, use 20 ppm or better. The CAN baud rate prescaler (BRP) and time segments must be configured using the CiA bit-timing calculator to satisfy propagation delay and sampling point requirements across the bus length.
The H temperature grade is rated -40C to +150C junction. Estimate: with 25 MHz active and all peripherals on, internal power dissipation stays below 100 mW, so theta_JA on the SPDIP-28 (typically 60-80 C/W) gives a junction-to-ambient rise of 8C or less. Even so, derate when ambient exceeds 100C; the silicon die is small and ambient dominates the thermal budget.
Keep the 28-pin SPDIP socket or PCB footprint to standard 0.100 inch (2.54 mm) row spacing and 0.300 inch (7.62 mm) row-to-row width - verified against Microchip package outline 28-006B. Route the CAN bus differential pair (CANTX/CANRX to external transceiver) as a matched 100 ohm differential pair; even short traces benefit from ground-referenced routing on an inner layer to maintain 50 ohm single-ended impedance.
コンプライアンス情報
RoHS and REACH compliant per Microchip product page. AEC-Q100 qualification is not applicable (PIC18F2585 family is not AEC-Q100 qualified in Microchip's automotive part list; H temperature grade is industrial). For AEC-Q100 qualified alternatives, contact Microchip automotive product line.
