PIC18F442-I/L - 40MHz 8-bit MCU 16KB Flash 44-PLCC | Microchip
部品番号: PIC18F442-I/L ✗ 生産終了| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $5.99 | $5.99 |
| 10 | $5.39 | $53.90 |
| 100 | $4.79 | $479.00 |
| 500 | $4.25 | $2,125.00 |
| 1,000 | $3.75 | $3,750.00 |
PIC18F442-I/L 概要
An 8-bit microcontroller is a single-chip computer built around an 8-bit data path and a small but powerful instruction set optimized for embedded control. PIC18-family devices sit in the upper tier of Microchip's 8-bit portfolio, sitting above the PIC16 family in code density, peripheral count, and MIPS throughput, while remaining part of the broader MCU -> embedded controller -> semiconductor taxonomy. The PIC18F442 specifically targets designs that need more code space and RAM than the PIC16 mid-range parts but do not yet justify stepping up to a PIC24 dsPIC or 32-bit MCU.
Key features include 34 digital I/O lines, a 10-bit A/D converter with 8 input channels, two Capture/Compare/PWM (CCP) modules, an enhanced USART, an MSSP configurable as SPI or I2C, and nanoWatt Technology dynamic power management. The 8-channel 10-bit ADC supports up to 8 multiplexed analog inputs, and the CCP peripherals make the device well-suited for motor control, power conversion, and PWM-driven actuator applications. The 256-byte on-chip EEPROM provides non-volatile data storage for calibration constants or user settings without external memory.
The architecture combines a 16-bit-wide instruction word with an 8-bit data path, allowing most instructions to execute in a single cycle. Self-programming capability, an ICD (In-Circuit Debugger) interface, and C-compiler friendly design reduce development friction. The PIC18F442 is upwardly code-compatible with PIC16C5X, PIC12CXXX, PIC16CXX, and PIC17CXX devices, giving engineers a migration path to higher performance without rewriting firmware.
Typical applications include industrial automation and control, automotive body and sensor subsystems, home appliances, sensor interfacing, small motor control, and low-power embedded nodes. The combination of EEPROM, ADC, CCP, and serial peripherals in a 44-pin package is a common fit for HVAC, vending, lighting control, and instrument front-end boards.
When designing with this device, budget the oscillator startup time and decoupling carefully; the PLCC package benefits from a ground plane and 100 nF ceramic bypass caps on each supply pin. Note that the PIC18F442-I/L is in Not Recommended for New Designs (NRND) status; existing designs can continue using it but new programs should evaluate the PIC18F452 successor family.
This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet alone.
ドロップイン代替品: PIC18F442-I/L — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: PIC18F442-I/L （同一形状・フットプリント） — 相違点: Package, Core Architecture, Mounting Type, Operating Temperature, Timers.
クイック比較ツール — 並列比較する代替部品を選択:
PIC18F452-I/L
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$6.85 / 個
データシートを見る →PIC18F4520-I/L
✅ ドロップイン📋 参考代替品（カタログ未掲載）
PIC18F442-I/P
✅ ドロップイン✓ 在庫あり
$5.4 / 個
データシートを見る →PIC18F442T-I/L
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$4.61 / 個
データシートを見る →PIC18F458-I/L
✅ ドロップイン✓ 在庫あり
$4.79 / 個
データシートを見る →PIC18F4420-I/PT
✅ ドロップイン📋 参考代替品（カタログ未掲載）
PIC18F442-I/L 最大定格＆電気的特性
| Core Processor | PIC |
| Core Size | 8-bit |
| Program Memory Type | Flash |
| Program Memory Size | 16 KB (8K x 16) |
| RAM Size | 768 bytes |
| EEPROM Size | 256 bytes |
| 最大クロック周波数 | 40 MHz |
| Instruction Set | 77 instructions, 16-bit opcode, 8-bit data |
| Throughput | 10 MIPS |
| Supply Voltage (Vdd) | 4.2 V to 5.5 V |
| I/O Pins | 34 |
| A/D Converter | 10-bit, 8 channels |
| CCP Modules | 2 (Capture/Compare/PWM) |
| Serial Interfaces | MSSP (SPI / I2C), Enhanced USART |
| パッケージ | 44-pin PLCC (J-Lead, 16.59 x 16.59 mm) |
| 動作温度 | -40 C to +85 C (Industrial) |
| 実装タイプ | Surface Mount |
| RoHS ステータス | Compliant |
| Power-Saving Modes | nanoWatt Technology (sleep, idle, etc.) |
PIC18F442-I/L ピン構成
| ピン 1 | MCLR — Master Clear (reset) input, active-low |
| ピン 2 | RA0/AN0 — Digital I/O / Analog input 0 |
| ピン 3 | RA1/AN1 — Digital I/O / Analog input 1 |
| ピン 4 | RA2/AN2/Vref- — Digital I/O / Analog input 2 / ADC Vref- |
| ピン 5 | RA3/AN3/Vref+ — Digital I/O / Analog input 3 / ADC Vref+ |
| ピン 6 | RA4/T0CKI — Digital I/O / Timer0 clock input |
| ピン 7 | RA5/AN4/SS — Digital I/O / Analog input 4 / SPI Slave Select |
| ピン 8 | OSC1/CLKI — Oscillator input / external clock input |
| ピン 9 | OSC2/CLKO/RA6 — Oscillator output / I/O |
| ピン 10 | RC0/T1OSO/T1CKI — Digital I/O / Timer1 oscillator output |
| ピン 11 | RC1/T1OSI/CCP2 — Digital I/O / Timer1 oscillator input / CCP2 |
| ピン 12 | RC2/CCP1 — Digital I/O / CCP1 PWM output |
| ピン 13 | RC3/SCK/SCL — Digital I/O / SPI clock / I2C clock |
| ピン 14 | RC4/SDI/SDA — Digital I/O / SPI data in / I2C data |
| ピン 15 | RC5/SDO — Digital I/O / SPI data out |
| ピン 16 | RC6/TX/CK — Digital I/O / USART TX / clock |
| ピン 17 | RC7/RX/DT — Digital I/O / USART RX / data |
| ピン 18 | Vss — Ground reference |
| ピン 19 | Vdd — Positive supply (4.2V - 5.5V) |
| ピン 20 | RB0/INT0 — Digital I/O / External interrupt 0 |
| ピン 21 | RB1/INT1 — Digital I/O / External interrupt 1 |
| ピン 22 | RB2/INT2 — Digital I/O / External interrupt 2 |
| ピン 23 | RB3/CCP2 — Digital I/O / CCP2 alternate |
| ピン 24 | RB4 — Digital I/O / interrupt-on-change |
| ピン 25 | RB5 — Digital I/O / interrupt-on-change |
| ピン 26 | RB6/PGC — Digital I/O / ICSP clock |
| ピン 27 | RB7/PGD — Digital I/O / ICSP data |
| ピン 28 | NC — Not connected (per datasheet) |
| ピン 29 | NC — Not connected (per datasheet) |
| ピン 30 | NC — Not connected (per datasheet) |
| ピン 31 | NC — Not connected (per datasheet) |
| ピン 32 | RD0/PSP0 — Digital I/O / Parallel Slave Port bit 0 |
| ピン 33 | RD1/PSP1 — Digital I/O / Parallel Slave Port bit 1 |
| ピン 34 | RD2/PSP2 — Digital I/O / Parallel Slave Port bit 2 |
| ピン 35 | RD3/PSP3 — Digital I/O / Parallel Slave Port bit 3 |
| ピン 36 | RD4/PSP4 — Digital I/O / Parallel Slave Port bit 4 |
| ピン 37 | RD5/PSP5 — Digital I/O / Parallel Slave Port bit 5 |
| ピン 38 | RD6/PSP6 — Digital I/O / Parallel Slave Port bit 6 |
| ピン 39 | RD7/PSP7 — Digital I/O / Parallel Slave Port bit 7 |
| ピン 40 | Vss — Ground reference |
| ピン 41 | Vdd — Positive supply (4.2V - 5.5V) |
| ピン 42 | RE0/RD/AN5 — Digital I/O / Read control / Analog input 5 |
| ピン 43 | RE1/WR/AN6 — Digital I/O / Write control / Analog input 6 |
| ピン 44 | RE2/CS/AN7 — Digital I/O / Chip select / Analog input 7 |
主な用途
PIC18F442-I/L の用途: 6 件s: Industrial Automation & Sensor Hubs, Automotive Body & Sensor Subsystems, Home Appliance Control Boards, HVAC & Climate Control Systems, Small Motor & Stepper Control, Test & Measurement Instruments.
Industrial Automation & Sensor Hubs
The PIC18F442-I/L is well-matched to industrial sensor-hub and PLC-front-end designs that require reliable 8-bit control over a 4.2-5.5 V supply. Its 8-channel 10-bit ADC samples multiple analog sensors (temperature, pressure, current) at up to 40 MHz instruction throughput, and the Enhanced USART supports RS-485 multi-drop industrial networks common in factory automation. The 256-byte on-chip EEPROM stores calibration coefficients and machine ID without external memory.
おすすめ
Automotive Body & Sensor Subsystems
The Industrial-temperature PIC18F442-I/L (-40 to +85 C) is used in non-powertrain automotive subsystems such as seat controllers, mirror modules, lighting controls, and HVAC actuators. Its two CCP modules generate PWM for LED drivers and small DC motor speed control, while the 10-bit ADC reads thermistors, position sensors, and current shunts. The 34 I/O pins comfortably drive multi-channel lighting or H-bridge interfaces in 12 V body-electronics environments.
おすすめ
Home Appliance Control Boards
Washing machines, dishwashers, microwave ovens, and induction cooktops frequently use PIC18F442-class devices for front-panel control and load management. The 8-channel ADC reads keypad touch sensors, NTC thermistors, and motor current; the two CCP channels drive TRIAC firing or variable-frequency inverter PWM at low cost. The 16 KB Flash and 768-byte RAM fit appliance state-machine firmware, and the PLCC-44 package simplifies wave-solder manufacturing.
おすすめ
HVAC & Climate Control Systems
HVAC controllers use the PIC18F442-I/L to read multiple temperature sensors, drive damper stepper motors or TRIAC-controlled fans, and communicate with thermostats over the Enhanced USART or MSSP. The 10 MIPS throughput easily handles PID loops for closed-loop temperature control, and the 256-byte EEPROM retains user-set schedules across power cycles. The wide Industrial temperature range supports unconditioned equipment-room installations.
おすすめ
Small Motor & Stepper Control
The two CCP modules on PIC18F442-I/L generate complementary PWM outputs suitable for brushed DC motor speed control and small bipolar stepper drives. The 40 MHz clock supports up to 10 MIPS, enabling closed-loop PID with reasonable update rates for fan, pump, and conveyor applications. The 8-channel ADC reads back-EMF or current shunt feedback for torque regulation, while the EUSART provides a diagnostic port for factory tuning.
おすすめ
Test & Measurement Instruments
Bench-top instruments such as digital multimeters, panel meters, and simple data loggers use the PIC18F442-I/L for the user interface, ADC scanning, and isolated serial communication to a host PC. The 10-bit ADC handles most general-purpose analog measurements, and the 256-byte EEPROM stores offset/gain calibration. The PLCC-44 footprint supports hand-rework-friendly prototyping while still being suitable for low-volume production.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: PIC18F442-I/L — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | PIC18F452-I/L | PIC18F4520-I/L | PIC18F458-I/L |
|---|---|---|---|---|
| Package | 44-pin PLCC (J-Lead) | 44-pin PLCC - same | 44-pin PLCC - same | 44-pin PLCC - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program Memory (Flash) | 16 KB | 32 KB | 32 KB | 32 KB |
| RAM Size | 768 bytes | 1536 bytes | 1536 bytes | 1536 bytes |
| EEPROM Size | 256 bytes | 256 bytes | 256 bytes | 256 bytes |
| Maximum Clock Speed | 40 MHz | 40 MHz | 40 MHz | 40 MHz |
| CAN Module | No | No | No | Yes |
| ADC Resolution / Channels | 10-bit / 8 channels | 10-bit / 8 channels | 10-bit / 8 channels | 10-bit / 8 channels |
| I/O Pins | 34 | 34 | 34 | 34 |
| Operating Voltage | 4.2 V to 5.5 V | 4.2 V to 5.5 V | 4.2 V to 5.5 V | 4.2 V to 5.5 V |
主な差別化要因
- Long-proven 44-pin PLCC footprint with broad ecosystem （vs PIC18F4520-I/L)
- Lower program-memory and RAM than successors （vs PIC18F452-I/L)
- No CAN, no enhanced PWM - simpler for non-networked control （vs PIC18F458-I/L)
設計ノート
The PIC18F442-I/L requires 4.2 V to 5.5 V on Vdd; unlike newer PIC18 K-series parts, it cannot operate down to 2.0 V. Place a 100 nF ceramic decoupling capacitor close to each Vdd pin (pins 19 and 41 on the PLCC-44 package), plus a bulk 10 uF tantalum or aluminum polymer on the main Vdd rail. The brown-out reset voltage is factory-configured; verify BOR enable bit in your initialization code to avoid unintended resets on noisy industrial supplies.
Estimated: at 40 MHz clock and 5.0 V supply, the PIC18F442-I/L draws approximately 16 mA active and under 1 uA in sleep mode. Total power dissipation at full activity is roughly 80 mW, well within the PLCC-44 package's ~1 W thermal limit, but industrial enclosures should still provide 100 mm^2 of copper on the PLCC thermal pad for margin. The nanoWatt Technology dynamic power-down modes can cut quiescent current by 100x for battery-backed nodes.
The 44-pin PLCC package uses J-lead surface-mount pads on a 1.27 mm pitch. Reserve at least 1 mm of clearance around the part for cleaning and inspection. Keep the OSC1/OSC2 traces short (under 10 mm) and surround them with a ground guard ring if the oscillator is feeding sensitive analog circuits. The MCLR pin should be pulled up to Vdd via 10 kohm and have a 100 nF cap to ground for reliable reset behavior.
PIC18F442-I/L is now NRND - Microchip no longer recommends it for new designs. Existing production can continue, but for new programs evaluate PIC18F452, PIC18F4520, or modern PIC18F K-series parts in the same or smaller packages. When migrating firmware, pay attention to the new oscillator PLL configuration bits, ADC acquisition time, and enhanced CCP register mapping, which differ from the F442 baseline.
コンプライアンス情報
RoHS and lead-free compliance per Microchip product page. PIC18F442-I/L is not AEC-Q100 qualified; for automotive use consider PIC18F458-I/L or modern AEC-graded parts. Halogen-free status not stated in the verified data.
