PIC18F452-E/ML - 8-bit MCU, 32KB Flash, 40MHz, 44-QFN | Microchip
部品番号: PIC18F452-E/ML ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $9.04 | $9.04 |
| 10 | $8.41 | $84.10 |
| 100 | $7.49 | $749.00 |
| 500 | $6.95 | $3,475.00 |
| 1,000 | $6.32 | $6,320.00 |
PIC18F452-E/ML 概要
What is a PIC18F 8-bit microcontroller? The PIC18F family is Microchip's high-performance 8-bit architecture built on a Harvard RISC core, upward compatible with PIC16C5X/PIC12CXXX/PIC16CXX/PIC17CXX devices. It targets mid-range embedded designs requiring more code space, more peripherals, and faster throughput than the PIC16F baseline. In the broader taxonomy: PIC18F -> 8-bit MCU -> microcontroller -> embedded processor -> semiconductor IC. This positioning makes it a workhorse for industrial control, instrumentation, and automotive subsystems.
Key features include 256 bytes of EEPROM, self-programming capability, an ICD (In-Circuit Debugger) interface, two Capture/Compare/PWM modules, an 8-channel 10-bit Analog-to-Digital converter, and a synchronous serial port configurable as either 3-wire SPI or 2-wire I2C. The C-compiler-friendly instruction set contains only 77 single-word instructions, lowering the learning curve for new firmware developers.
Architecturally, the PIC18F452 integrates a 16-bit wide instruction path with separate program and data buses, enabling single-cycle instruction fetch plus ALU operation in most cases. The 10-bit ADC with 8 channels supports acquisition of mixed analog signals from sensors, while the dual PWM modules provide flexible motor or power control. The extended temperature grade (E) plus QFN package make it suitable for thermally constrained or vibration-prone environments.
Typical applications include industrial automation controllers, HVAC peripherals, automotive body modules, sensor signal conditioning, and battery-powered metering. The combination of EEPROM storage and self-programming also supports field-upgradeable end products.
When designing with this device, ensure the 44-QFN exposed pad is properly soldered to a sufficiently large copper pour for thermal dissipation; QFN packages require careful PCB layout to avoid tombstoning. For new designs, consider the pin-compatible PIC18F4520 family which offers enhanced peripherals and nanoWatt technology for lower sleep current.
This page synthesizes distributor pricing, drop-in alternatives from the PIC18F family, and practical design notes not found in the manufacturer datasheet alone.
ドロップイン代替品: PIC18F452-E/ML — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: PIC18F452-E/ML （同一形状・フットプリント） — 相違点: Package, Program Memory (Flash), RAM, Operating Temperature, Serial Interfaces.
クイック比較ツール — 並列比較する代替部品を選択:
PIC18F452-I/ML
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
PIC18F452T-E/ML
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
PIC18F452-E/L
✅ ドロップイン✓ 在庫あり
$8.4 / 個
データシートを見る →PIC18F4520-I/ML
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
PIC18F442-E/ML
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
PIC18F4523T-I/ML
✅ ドロップイン✓ 在庫あり
$4.41 / 個
データシートを見る →PIC18F4525-I/PT
✅ ドロップイン✓ 在庫あり
$4.18 / 個
データシートを見る →PIC18F452-E/ML 最大定格＆電気的特性
| Core Architecture | PIC 8-bit RISC |
| Program Memory (Flash) | 32 KB (16K x 16) |
| RAM | 1536 bytes |
| EEPROM | 256 bytes |
| Maximum CPU Speed | 40 MHz (10 MIPS) |
| I/O Pins | 34 |
| ADC | 10-bit, 8 channels |
| Timers | 1 x 8-bit + 3 x 16-bit |
| CCP/PWM Modules | 2 |
| Serial Interfaces | SPI, I2C (MSSP), USART |
| Operating Voltage | 2.0 V to 5.5 V |
| 動作温度 | -40C to +125C (Extended -E grade) |
| パッケージ | 44-pin QFN (8x8 mm) |
| Instruction Set | 77 instructions, 16-bit wide |
| Self-Programming | Yes (ICSP) |
| In-Circuit Debug | Yes (ICD) |
| RoHS ステータス | Compliant |
PIC18F452-E/ML ピン構成
| ピン 1 | MCLR — Master Clear (reset) input, active low |
| ピン 2 | RA0/AN0 — PORTA bit 0 / analog input 0 |
| ピン 3 | RA1/AN1 — PORTA bit 1 / analog input 1 |
| ピン 4 | RA2/AN2/VREF- — PORTA bit 2 / analog input 2 / VREF- |
| ピン 5 | RA3/AN3/VREF+ — PORTA bit 3 / analog input 3 / VREF+ |
| ピン 6 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| ピン 7 | RA5/AN4/SS — PORTA bit 5 / analog input 4 / SPI slave select |
| ピン 8 | RE0/RD/AN5 — PORTE bit 0 / read control / analog input 5 |
| ピン 9 | RE1/WR/AN6 — PORTE bit 1 / write control / analog input 6 |
| ピン 10 | RE2/CS/AN7 — PORTE bit 2 / chip select / analog input 7 |
| ピン 11 | VDD — Positive supply voltage |
| ピン 12 | VSS — Ground reference |
| ピン 13 | OSC1/CLKI — Crystal oscillator input / external clock in |
| ピン 14 | OSC2/CLKO — Crystal oscillator output / clock out |
| ピン 15 | RC0/T1OSO/T1CKI — PORTC bit 0 / Timer1 oscillator out / Timer1 clock in |
| ピン 16 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator in / CCP2 I/O |
| ピン 17 | RC2/CCP1 — PORTC bit 2 / CCP1 I/O |
| ピン 18 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I2C clock |
| ピン 19 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| ピン 20 | RC5/SDO — PORTC bit 5 / SPI data out |
| ピン 21 | RC6/TX/CK — PORTC bit 6 / USART TX / USART clock |
| ピン 22 | RC7/RX/DT — PORTC bit 7 / USART RX / USART data |
| ピン 23 | RD0/PSP0 — PORTD bit 0 / parallel slave port bit 0 |
| ピン 24 | RD1/PSP1 — PORTD bit 1 / parallel slave port bit 1 |
| ピン 25 | RD2/PSP2 — PORTD bit 2 / parallel slave port bit 2 |
| ピン 26 | RD3/PSP3 — PORTD bit 3 / parallel slave port bit 3 |
| ピン 27 | RD4/PSP4 — PORTD bit 4 / parallel slave port bit 4 |
| ピン 28 | RD5/PSP5 — PORTD bit 5 / parallel slave port bit 5 |
| ピン 29 | RD6/PSP6 — PORTD bit 6 / parallel slave port bit 6 |
| ピン 30 | RD7/PSP7 — PORTD bit 7 / parallel slave port bit 7 |
| ピン 31 | VSS — Ground reference |
| ピン 32 | VDD — Positive supply voltage |
| ピン 33 | RB0/INT0 — PORTB bit 0 / external interrupt 0 |
| ピン 34 | RB1/INT1 — PORTB bit 1 / external interrupt 1 |
| ピン 35 | RB2/INT2 — PORTB bit 2 / external interrupt 2 |
| ピン 36 | RB3/CCP2 — PORTB bit 3 / CCP2 I/O |
| ピン 37 | RB4 — PORTB bit 4 |
| ピン 38 | RB5/PGM — PORTB bit 5 / LVP programming |
| ピン 39 | RB6/PGC — PORTB bit 6 / ICD clock |
| ピン 40 | RB7/PGD — PORTB bit 7 / ICD data |
| ピン 41 | NC — Not connected (per datasheet) |
| ピン 42 | NC — Not connected (per datasheet) |
| ピン 43 | NC — Not connected (per datasheet) |
| ピン 44 | NC — Not connected (per datasheet) |
主な用途
PIC18F452-E/ML の用途: 6 件s: Industrial Automation Controller, Automotive Body Control Module, HVAC Peripheral Controller, Battery-Powered Smart Meter, Medical Monitoring Peripheral, Sensor Signal Conditioning Hub.
Industrial Automation Controller
The PIC18F452-E/ML is well suited for industrial PLC and motor-driver slave controllers because of its 32 KB FLASH (sufficient for state-machine + Modbus RTU stacks), 8-channel 10-bit ADC (sampling up to 8 sensor inputs concurrently), and two CCP/PWM modules (driving servo valves or stepper motor pulse/direction signals at 40 MHz). Its -40C to +125C extended temperature grade supports deployment near furnace exhausts and outdoor panels. The PIC18F452-E/ML's C-compiler-friendly 77-instruction set eases porting of control algorithms from ladder logic or higher-level languages. The PIC18F452-E/ML operates from 2.0-5.5 V, simplifying 24V-to-5V industrial bus implementations. Compared with PIC16F alternatives, this part's larger RAM (1536 B) handles Modbus buffers and PID controller histories without external memory.
おすすめ
Automotive Body Control Module
In automotive body and comfort modules (window lifters, mirror controllers, seat positioners), the PIC18F452-E/ML brings the -40C to +125C extended temperature range required for under-dash and door-mounted electronics, plus 34 I/O pins to drive relays, H-bridges, and switch-scan matrices. The 10 MIPS throughput handles LIN-like software UART alongside the hardware USART, while the dual PWM modules generate motor control signals. EEPROM (256 bytes) stores calibration and position memory across power cycles. The 44-pin QFN (8x8 mm) package is footprint-compatible with the PIC18F4520-I/ML, allowing easy migration to nanoWatt parts for key-off quiescent current reduction. The PIC18F452-E/ML's 2.0-5.5 V operation survives 12V automotive cranking transients when paired with a TVS-protected 5V regulator.
おすすめ
HVAC Peripheral Controller
The PIC18F452-E/ML fits HVAC peripheral designs (thermostats, damper actuators, fan-speed controllers) thanks to its 8-channel ADC for temperature/pressure sensing, dual PWM for proportional valve and blower control, and 32 KB FLASH for proportional-integral control loops with display menus. Its Extended temperature grade handles plenum-adjacent mounting where ambient can exceed +85C. The MSSP peripheral implements I2C communication with HVAC network transceivers or sensor front-ends, while the USART handles service-port diagnostics. Compared to PIC16F baselines, the PIC18F452-E/ML's 1536-byte RAM accommodates touchscreen UI buffers and scheduling state. Pin compatibility with PIC18F4520-I/ML enables drop-in upgrades to lower sleep current (nanoWatt) for battery-backed thermostat retention.
おすすめ
Battery-Powered Smart Meter
For battery-powered metering (water, gas, heat, energy submetering), the PIC18F452-E/ML's 32 KB FLASH stores protocol stacks (Wireless M-Bus, LoRaWAN node firmware) and 1536-byte RAM holds measurement buffers and encryption contexts. Its 2.0-5.5 V operation is ideal for 3.6V lithium thionyl chloride cells, and the 10-bit ADC captures pulse-output meter sensors. The Extended temperature grade suits outdoor meter enclosures. Sleep-mode current on the legacy PIC18F452 is relatively high (~50 uA typical), so for new designs the pin-compatible PIC18F4520-I/ML with nanoWatt technology (<1 uA sleep) is preferred, with the PIC18F452-E/ML remaining a viable option where firmware reuse is critical.
おすすめ
Medical Monitoring Peripheral
The PIC18F452-E/ML supports medical peripherals (patient monitors, infusion pump controllers, diagnostic instrument front-ends) requiring reliable 8-bit processing and extended temperature operation. Its 32 KB FLASH accommodates IEC 62304-friendly firmware architectures, the 8-channel 10-bit ADC acquires multiple bioelectric or optical sensor inputs, and EEPROM (256 bytes) stores calibration data. C-compiler friendliness and an ICD debug interface simplify validation. Note: while the PIC18F452-E/ML can be used in medical designs, end-product certification (FDA, CE-MDR) remains the integrator's responsibility, and newer pin-compatible parts like the PIC18F4520-I/ML offer better long-term availability for medical product life cycles.
おすすめ
Sensor Signal Conditioning Hub
The PIC18F452-E/ML serves as a multi-sensor signal-conditioning hub in industrial and instrumentation equipment, with 8 ADC channels for thermocouple/bridge/4-20 mA inputs and dual PWM for excitation or heater control. The 32 KB FLASH holds linearization tables and digital filter coefficients; 1536-byte RAM buffers sample streams before forwarding via SPI or USART. The Extended temperature grade suits unheated enclosures. Compared to smaller PIC16F parts, the PIC18F452-E/ML's C-friendly architecture enables complex math (Kalman filtering, FFT) without assembly. Pin compatibility with PIC18F4520-I/ML simplifies migration when nanoWatt features are needed. Combined with an external op-amp (e.g., MCP6N11) and precision reference, the PIC18F452-E/ML forms a complete 16-bit-class signal chain.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: PIC18F452-E/ML — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | PIC18F452-I/ML | PIC18F452T-E/ML | PIC18F4520-I/ML | PIC18F442-E/ML | PIC18F4523T-I/ML |
|---|---|---|---|---|---|---|
| Package | 44-pin QFN (8x8 mm) | 44-pin QFN (8x8 mm) - same | 44-pin QFN (8x8 mm) - same | 44-pin QFN (8x8 mm) - same | 44-pin QFN (8x8 mm) - same | 44-pin QFN (8x8 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| FLASH | 32 KB | 32 KB | 32 KB | 32 KB | 16 KB | 32 KB |
| RAM | 1536 B | 1536 B | 1536 B | 1536 B | 768 B | 1536 B |
| EEPROM | 256 B | 256 B | 256 B | 256 B | 256 B | 256 B |
| CPU Speed | 40 MHz / 10 MIPS | 40 MHz / 10 MIPS | 40 MHz / 10 MIPS | 40 MHz / 10 MIPS | 40 MHz / 10 MIPS | 40 MHz / 10 MIPS |
| Temperature Grade | -40C to +125C (E) | -40C to +85C (I) | -40C to +125C (E) | -40C to +85C (I) | -40C to +125C (E) | -40C to +85C (I) |
| nanoWatt Technology | No | No | No | Yes | No | Yes |
主な差別化要因
- Extended temperature grade qualified to +125C （vs PIC18F452-I/ML)
- Full 32 KB FLASH + 1536 B RAM headroom for protocols （vs PIC18F442-E/ML)
- QFN package with thermal pad for high-density layouts （vs PIC18F452-E/L (PLCC-44))
- Mature firmware ecosystem with legacy code reuse （vs PIC18F4520-I/ML)
設計ノート
Estimated: The PIC18F452-E/ML 44-QFN package exposes a thermal pad on the underside that MUST be soldered to a ground copper pour of at least 1 square inch (645 mm^2) to meet the -40C to +125C thermal envelope. Without proper thermal connection, junction temperature can rise ~25C above ambient per watt of internal dissipation. Failure to solder the thermal pad results in tombstoning during reflow and chronic reliability problems. Use via-in-pad or via-fan patterns to maximize heat transfer to inner copper layers.
Place a 100 nF decoupling capacitor within 5 mm of each VDD/VSS pair (the PIC18F452-E/ML has two VDD/VSS pairs at pins 11/12 and 31/32). Add a bulk 10 uF tantalum or ceramic capacitor near the supply pins. The ADC's VREF+ pin (RA3) should be bypassed with a 100 nF ceramic when used; noisy VREF directly couples into ADC readings and degrades effective ENOB by 1-2 bits.
The PIC18F452-E/ML's MCLR pin (pin 1) MUST be tied to VDD through a 10 kohm resistor for normal operation; leaving it floating causes unpredictable resets. If using ICD debugging, MCLR is driven by the debugger and the pull-up should be removed. Also note: the RB5/PGM pin is used for low-voltage programming - never tie it directly to VDD; route through a 10 kohm pull-up to avoid programming interference.
Keep analog inputs (RA0-RA5, RE0-RE2) physically separated from switching signals (PWM outputs, oscillator traces) on the PCB to minimize crosstalk into ADC readings. The PIC18F452 datasheet recommends a ground plane under the analog section with a single-point connection to digital ground near the MCU's VSS pins. Route the crystal traces (OSC1/OSC2) with short, symmetric traces and guard them with ground to reduce EMI.
The PIC18F452-E/ML's parallel slave port (PORTD) can capture external bus data but only at the system clock rate; verify that external timing meets the tRD setup and hold specifications in the datasheet to avoid data corruption. The MSSP peripheral operating in I2C mode requires 4.7 kohm pull-ups on SDA/SCL for standard-mode (100 kHz); for fast-mode (400 kHz) use 2.2 kohm pull-ups. Slew-rate control is not configurable on this legacy part, so external filtering may be required in EMI-sensitive environments.
コンプライアンス情報
RoHS compliant per Microchip product page. Not AEC-Q100 qualified - this part is Extended temp grade (-E) but does not carry automotive qualification. For AEC-Q100 automotive designs consider PIC18F452 family with /VAO suffix or migrate to PIC18F458 (CAN) or PIC18F46K22.
