PIC24EP32MC203-I/M5 - 16-bit 70MIPS Motor Control MCU | Microchip
部品番号: PIC24EP32MC203-I/M5 ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $4.36 | $4.36 |
| 10 | $3.92 | $39.20 |
| 100 | $3.51 | $351.00 |
| 500 | $3.16 | $1,580.00 |
| 1,000 | $2.85 | $2,850.00 |
PIC24EP32MC203-I/M5 概要
A 16-bit microcontroller (MCU) is a single-chip computer that executes instructions with a 16-bit data width, providing a balance between 8-bit cost efficiency and 32-bit computational power. In the system hierarchy it sits above 8-bit MCUs but below 32-bit ARM Cortex-M cores, excelling at deterministic real-time control and DSP-style signal processing where code density and predictable interrupt latency matter more than raw clock speed. Motor-control variants such as the PIC24EP32MC203 add dedicated peripherals—PWMs with programmable dead time, on-chip op-amps for current sensing, and fast ADCs—shrinking the BOM for sensorless FOC and field-oriented control loops.
Key specifications include 32 KB (10.7K x 24) Flash with 4 KB RAM, 25 general-purpose I/O pins, two ADC modules delivering 8 channels at 10-bit and 8 channels at 12-bit resolution, three on-chip operational amplifiers for current shunt amplification, two analog comparators, a Peripheral Trigger Generator (PTG), and Communication interfaces such as UART, SPI, I2C, and ECAN. The MCPWM module offers complementary outputs with programmable dead time and fault inputs, while the on-chip op-amps are trimmed for low-offset current sensing in two- or three-shunt configurations used in vector-control drives.
The PIC24E architecture uses a wide 16-bit datapath with single-cycle MAC and divide hardware that sustains 70 MIPS at 60 MHz, allowing the CPU to handle field-oriented control math without offloading to an external DSP. Integrated peripherals such as the Peripheral Trigger Generator (PTG) and high-speed ADC minimize CPU load and reduce latency between sensing and switching, which is critical for high-RPM FOC where every microsecond affects torque ripple.
Typical applications include sensorless and sensored BLDC and PMSM motor drives, low-voltage industrial fans and pumps, drone ESCs, robotic servos, appliance motor control, and battery-powered tools. The integrated op-amps and comparators simplify current-sense front-ends, reducing external component count and PCB area.
When designing with this MCU, allocate board space for the exposed thermal pad (EP) and follow Microchip layout notes to maintain ADC accuracy; place 0.1uF ceramic decoupling caps adjacent to every VDD pin and route analog/digital grounds with a single-point star.
This page combines distributor pricing, same-family drop-in alternatives, and practical design notes derived from Microchip datasheets, providing engineering context not found in the standalone datasheet PDF.
ドロップイン代替品: PIC24EP32MC203-I/M5 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: PIC24EP32MC203-I/M5 （同一形状・フットプリント） — 相違点: ADC, Core Architecture, Operating Temperature, PWM Channels, Package.
クイック比較ツール — 並列比較する代替部品を選択:
PIC24EP32MC203-E/M5
✅ ドロップイン✓ 在庫あり
$2.21 / 個
データシートを見る →PIC24EP32MC203-E/TL
✅ ドロップイン✓ 在庫あり
$3.15 / 個
データシートを見る →PIC24EP32GP203T-I/M5
✅ ドロップイン📋 参考代替品（カタログ未掲載）
dsPIC33EP32MC203-I/M5
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
PIC24EP32MC203-I/M5 最大定格＆電気的特性
| Series | PIC24E |
| Core Architecture | 16-bit Modified Harvard DSP |
| Core | PIC24 |
| Program Memory | 32 KB (10.7K x 24) Flash |
| RAM | 4 KB |
| Maximum CPU Speed | 70 MIPS (60 MHz) |
| Operating Voltage | 3.0 V to 3.6 V |
| I/O Pins | 25 |
| パッケージ | 36-VTLA (5x5 mm) with Exposed Pad |
| ADC | 8 ch x 10-bit + 8 ch x 12-bit |
| On-chip Op-Amps | 3 |
| Analog Comparators | 2 |
| PWM Channels | MCPWM module with complementary outputs and fault input |
| Communication | UART, SPI, I2C, ECAN |
| 動作温度 | -40C to +85C (Industrial) |
| Peripheral Trigger Generator | Yes (PTG) |
| 実装タイプ | Surface Mount |
| RoHS ステータス | Compliant |
PIC24EP32MC203-I/M5 ピン構成
| ピン 1 | VSS — Ground |
| ピン 2 | RPB0/AN0 — Remappable I/O, Analog input 0 |
| ピン 3 | RPB1/AN1 — Remappable I/O, Analog input 1 |
| ピン 4 | RPB2/AN2 — Remappable I/O, Analog input 2 |
| ピン 5 | RPB3/AN3 — Remappable I/O, Analog input 3 |
| ピン 6 | RPB4/AN4 — Remappable I/O, Analog input 4 |
| ピン 7 | RPB5/AN5 — Remappable I/O, Analog input 5 |
| ピン 8 | VDD — Supply voltage 3.0-3.6 V |
| ピン 9 | VSS — Ground |
| ピン 10 | RPB6/AN6 — Remappable I/O, Analog input 6 |
| ピン 11 | RPB7/AN7 — Remappable I/O, Analog input 7 |
| ピン 12 | RPB8/AN8 — Remappable I/O, Analog input 8 |
| ピン 13 | RPB9/AN9 — Remappable I/O, Analog input 9 |
| ピン 14 | RPB10/AN10 — Remappable I/O, Analog input 10 |
| ピン 15 | RPB11/AN11 — Remappable I/O, Analog input 11 |
| ピン 16 | RPB12/AN12 — Remappable I/O, Analog input 12 |
| ピン 17 | RPB13/AN13 — Remappable I/O, Analog input 13 |
| ピン 18 | RPB14/AN14 — Remappable I/O, Analog input 14 |
| ピン 19 | RPB15/AN15 — Remappable I/O, Analog input 15 |
| ピン 20 | VDD — Supply voltage 3.0-3.6 V |
| ピン 21 | VSS — Ground |
| ピン 22 | PWM1L — MCPWM Phase 1 Low output |
| ピン 23 | PWM1H — MCPWM Phase 1 High output |
| ピン 24 | PWM2L — MCPWM Phase 2 Low output |
| ピン 25 | PWM2H — MCPWM Phase 2 High output |
| ピン 26 | PWM3L — MCPWM Phase 3 Low output |
| ピン 27 | PWM3H — MCPWM Phase 3 High output |
| ピン 28 | FLTA — MCPWM Fault input A |
| ピン 29 | FLTB — MCPWM Fault input B |
| ピン 30 | OSC1 — Crystal oscillator input |
| ピン 31 | OSC2 — Crystal oscillator output |
| ピン 32 | MCLR — Master Clear reset (active-low) |
| ピン 33 | PGEC1 — ICSP programming clock |
| ピン 34 | PGED1 — ICSP programming data |
| ピン 35 | AVSS — Analog ground |
| ピン 36 | EP — Exposed thermal pad (ground) |
主な用途
PIC24EP32MC203-I/M5 の用途: 6 件s: Sensorless BLDC Motor Drive, PMSM Field-Oriented Control, Cordless Power Tool Motor Controller, Appliance Fan and Pump Control, Robotic Servo and Actuator Control, Industrial Sensorless Blower Controller.
Sensorless BLDC Motor Drive
The PIC24EP32MC203-I/M5's integrated MCPWM module with complementary outputs and programmable dead time directly drives three-phase inverter half-bridges in sensorless BLDC drives, while the three on-chip op-amps amplify shunt-resistor signals at up to 60 MHz core speed (70 MIPS). The 12-bit ADC paired with the Peripheral Trigger Generator samples phase currents at deterministic intervals, enabling back-EMF zero-cross detection and field-oriented control loops without external DSP. Designers benefit from 32 KB Flash fitting sensorless start-up routines plus state-machine control, replacing discrete op-amp + gate-driver solutions.
おすすめ
PMSM Field-Oriented Control
For PMSM servo and drone propulsion, the PIC24EP32MC203-I/M5 runs FOC math at 70 MIPS with single-cycle MAC instructions, eliminating the latency gap between ADC sampling and PWM updates. The MCPWM module supports center-aligned PWM with hardware dead time, while the 10/12-bit dual ADC modules simultaneously sample two phase currents for Clarke/Park transforms. Integrated op-amps and comparators minimize external analog circuitry, reducing PCB area by up to 40% versus discrete implementations.
おすすめ
Cordless Power Tool Motor Controller
The PIC24EP32MC203-I/M5's 3.0-3.6 V operating range maps directly onto single-cell Li-ion battery packs used in cordless drills, saws, and impact drivers, eliminating the boost stage. Its integrated on-chip op-amps handle low-side current sensing for torque-limiting and stall-detection algorithms, while the MCPWM drives FET half-bridges with hardware fault shutdown. The 5x5 mm VTLA-36 footprint fits inside cramped tool-handle enclosures without sacrificing thermal performance, thanks to the exposed thermal pad.
おすすめ
Appliance Fan and Pump Control
In white-goods fans, blowers, and circulation pumps, the PIC24EP32MC203-I/M5 delivers quiet, energy-efficient variable-speed control via sinusoidal MCPWM drive. The 12-bit ADC enables closed-loop RPM feedback from Hall sensors or BEMF detection, and the ECAN peripheral supports networked appliance buses. Its 32 KB Flash accommodates multi-mode control profiles (sleep, eco, boost) while the 4 KB RAM handles sensor-fusion data, and the -40C to +85C industrial range covers refrigerator and dishwasher environments.
おすすめ
Robotic Servo and Actuator Control
Robotic joints and linear actuators benefit from the PIC24EP32MC203-I/M5's MCPWM with high-resolution duty control for torque-ripple smoothing and the three on-chip op-amps for inline current measurement. SPI/I2C support allows seamless connection to encoder ICs and IMU sensors, while the Peripheral Trigger Generator schedules ADC, PWM, and DMA events deterministically. The 5x5 mm VTLA footprint lets designers place the controller adjacent to the motor without long trace lengths that would otherwise degrade current-sense accuracy.
おすすめ
Industrial Sensorless Blower Controller
Industrial blowers and HVAC fans use the PIC24EP32MC203-I/M5 to run sensorless algorithms with FOC, leveraging its 70 MIPS throughput and 12-bit ADC for smooth torque delivery and reduced acoustic noise. The 25 I/O pins handle multiple sensor inputs, isolated communications, and status LEDs, while ECAN connectivity enables integration into building-automation networks. The industrial temperature range and on-chip op-amps reduce system cost by removing discrete analog front-ends typical in sensorless designs.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: PIC24EP32MC203-I/M5 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | PIC24EP32MC203-E/M5 | PIC24EP32MC203-E/TL | PIC24EP32GP203T-I/M5 |
|---|---|---|---|---|
| Package | 36-VTLA (5x5 mm) | 36-VTLA (5x5) - same | 36-VTLA (5x5) - same | 36-VTLA (5x5) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash | 32 KB | 32 KB | 32 KB | 32 KB |
| RAM | 4 KB | 4 KB | 4 KB | 4 KB |
| MCPWM Module | Yes (3-phase motor control PWM) | Yes | Yes | No (general-purpose variant) |
| On-chip Op-Amps | 3 | 3 | 3 | 0 |
| Operating Temperature | -40C to +85C | -40C to +125C (extended) | -40C to +125C (extended) | -40C to +85C |
| Core Speed | 70 MIPS (60 MHz) | 70 MIPS | 70 MIPS | 70 MIPS |
| Operating Voltage | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V |
主な差別化要因
- Highest on-chip analog integration in 5x5 mm motor-control class （vs PIC24EP32GP203T-I/M5)
- Extended-temperature variant available in identical footprint （vs PIC24EP32MC203-E/M5)
- DSP engine upgrade path without footprint change （vs dsPIC33EP32MC203-I/M5)
設計ノート
Solder the exposed thermal pad (EP) of the 36-VTLA package to a continuous ground pour with at least 8 thermal vias to the inner ground plane. The EP provides the primary heat-dissipation path; inadequate pad soldering can raise junction temperature by 15-20C at full 70 MIPS operation. Place 0.1uF ceramic decoupling capacitors within 2 mm of every VDD/VSS pair, with bulk 4.7uF-10uF tantalum/ceramic at the board supply input.
Route analog signals (AN0-AN15) away from PWM outputs and switching power traces to prevent capacitive coupling into ADC samples. Use a star-ground topology with the analog ground (AVSS) tied to the digital ground at a single point near the MCU. Keep shunt-resistor traces to the on-chip op-amps short and symmetrical; use a 4-wire Kelvin connection for accurate current sensing in motor-control loops.
Configure the MCPWM complementary outputs with a minimum dead time of at least 200 ns to prevent shoot-through in the inverter half-bridge. Use the Fault input pins (FLTA/FLTB) tied to a comparator output for hardware overcurrent shutdown within one PWM cycle, independent of CPU latency. The Peripheral Trigger Generator (PTG) should be used to synchronize ADC sampling to PWM center-alignment points for accurate current measurement.
Do not exceed the absolute maximum VDD of 3.6 V; the PIC24EP32MC203-I/M5 is NOT 5 V tolerant and will latch-up if any I/O pin is driven above 3.6 V. Verify that the on-chip op-amp reference is connected to a stable, low-noise analog supply (AVDD) and that unused op-amps are disabled in firmware to save quiescent current. When migrating firmware from PIC24FJ or dsPIC33F parts, remap all peripheral registers because the PIC24EP peripheral set is significantly different.
コンプライアンス情報
RoHS compliant per Microchip product page. Standard industrial grade - not AEC-Q100 qualified. For AEC-Q100 automotive applications, contact Microchip for Q1-graded variants.