PIC32MX564F064L-I/PT - 80MHz 64KB Flash 32-bit MCU | Microchip
部品番号: PIC32MX564F064L-I/PT ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $7.95 | $7.95 |
| 10 | $7.18 | $71.80 |
| 100 | $6.05 | $605.00 |
| 500 | $5.42 | $2,710.00 |
| 1,000 | $4.85 | $4,850.00 |
PIC32MX564F064L-I/PT 概要
A 32-bit microcontroller (MCU) is a microcontroller built around a 32-bit data path and registers, allowing single-instruction handling of values larger than 8 or 16 bits. The PIC32MX5xx/6xx/7xx family extends Microchip's PIC architecture into 32-bit territory using the MIPS M4K core, sitting hierarchically as: microcontroller -> 32-bit MCU -> MIPS MCU -> PIC32 family -> embedded processor. This category combines the deterministic interrupt response of legacy PIC16/PIC24 devices with DSP-class throughput suitable for USB, CAN, and graphics applications.
Key features include integrated Full-Speed USB 2.0 device/host/OTG, a CAN 2.0B module, four DMA channels with programmable automatic transfer, a 10-bit 1Msps ADC with up to 16 channels, and a parallel master port (PMP) for external bus interfacing. The device also exposes an Enhanced Parallel Master Port, 5x 16-bit timers, and two UART/SPI/I2C modules. Hardware crypto accelerators are absent - encryption must be implemented in firmware.
Technical depth: the 80MHz core delivers 1.56 DMIPS/MHz, executing most instructions in a single cycle and consuming approximately 1.1 mA/MHz active current. Flash prefetch and a 256-bit-wide flash bus keep wait states to zero at full speed. Integrated peripherals are mapped to dedicated DMA channels, allowing the core to remain quiescent while serial or ADC transfers occur.
Typical applications include industrial automation HMI panels, USB-based data loggers, automotive body controllers, point-of-sale terminals, and CAN-enabled sensor hubs. The combination of USB and CAN with 53 GPIO makes the part well suited for industrial bridging gateways. For consumer audio or low-power wearables, however, designers should look at PIC32MX2xx parts with lower active current.
Design consideration: at 80MHz and 3.3V the device draws roughly 88 mA, requiring careful decoupling - place one 0.1uF X7R plus one 10uF bulk capacitor within 5 mm of each power pin pair. Trace lengths on the 80MHz system clock and USB DP/DM lines must be impedance-matched to 90 ohms differential.
This page synthesizes distributor pricing, drop-in alternatives within the same TQFP-100 footprint, and practical design notes not consolidated in the manufacturer datasheet.
ドロップイン代替品: PIC32MX564F064L-I/PT — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: PIC32MX564F064L-I/PT （同一形状・フットプリント） — 相違点: ADC, CAN, USB, Operating Temperature, MSL Level.
クイック比較ツール — 並列比較する代替部品を選択:
PIC32MX564F064HT-I/PT
✅ ドロップイン📋 参考代替品（カタログ未掲載）
PIC32MX564F064L-V/PT
✅ ドロップイン📋 参考代替品（カタログ未掲載）
PIC32MX564F064LT-I/PT
✅ ドロップイン✓ 在庫あり
$3.65 / 個
データシートを見る →PIC32MX534F064L-I/PT
✅ ドロップイン✓ 在庫あり
$4.95 / 個
データシートを見る →PIC32MX564F064L-I/BG
✅ ドロップイン✓ 在庫あり
$4.45 / 個
データシートを見る →PIC32MX564F064L-I/PT 最大定格＆電気的特性
| Core Architecture | MIPS32 M4K 32-bit RISC |
| Maximum CPU Speed | 80 MHz |
| Program Flash Memory | 64 KB (64K x 8) |
| SRAM | 32 KB (32K x 8) |
| Number of I/O Pins | 53 |
| パッケージ / ケース | 100-pin TQFP (12x12 mm) |
| Supply Voltage (VDD) | 2.3 V to 3.6 V |
| 動作温度 | -40 C to +85 C (Industrial, -I suffix) |
| USB Module | USB 2.0 Full-Speed Device/Host/OTG |
| CAN Module | CAN 2.0B |
| DMA Channels | 4 (with programmable automatic transfer) |
| ADC | 10-bit, up to 1 Msps, 16 channels |
| Timers | 5 x 16-bit |
| Communication Peripherals | 2x UART, 2x SPI, 2x I2C, PMP |
| Oscillator | Internal 8 MHz + PLL; external crystal support |
| 実装タイプ | Surface Mount (TQFP) |
| MSLレベル | MSL3 (per JEDEC J-STD-020) |
| RoHS ステータス | Compliant |
PIC32MX564F064L-I/PT ピン構成
| ピン 1 | RG15 — General purpose I/O / PMALL |
| ピン 2 | SDA1 — I2C1 data |
| ピン 3 | SCL1 — I2C1 clock |
| ピン 4 | RG6 — General purpose I/O |
| ピン 5 | VSS — Ground |
| ピン 6 | VDD — Positive supply (2.3-3.6V) |
| ピン 7 | RG7 — General purpose I/O |
| ピン 8 | RG8 — General purpose I/O |
| ピン 9 | RG9 — General purpose I/O |
| ピン 10 | VSS — Ground |
| ピン 11 | RF0 — General purpose I/O |
| ピン 12 | RF1 — General purpose I/O |
| ピン 13 | RG0 — General purpose I/O |
| ピン 14 | RG1 — General purpose I/O |
| ピン 15 | PMA0 — Parallel master port address 0 |
| ピン 16 | PMA1 — Parallel master port address 1 |
| ピン 17 | PMA2 — Parallel master port address 2 |
| ピン 18 | PMA3 — Parallel master port address 3 |
| ピン 19 | PMA4 — Parallel master port address 4 |
| ピン 20 | PMA5 — Parallel master port address 5 |
| ピン 21 | PMD0 — Parallel master port data 0 |
| ピン 22 | PMD1 — Parallel master port data 1 |
| ピン 23 | PMD2 — Parallel master port data 2 |
| ピン 24 | PMD3 — Parallel master port data 3 |
| ピン 25 | PMD4 — Parallel master port data 4 |
| ピン 26 | PMD5 — Parallel master port data 5 |
| ピン 27 | PMD6 — Parallel master port data 6 |
| ピン 28 | PMD7 — Parallel master port data 7 |
| ピン 29 | PMD8 — Parallel master port data 8 |
| ピン 30 | PMD9 — Parallel master port data 9 |
| ピン 31 | PMD10 — Parallel master port data 10 |
| ピン 32 | PMD11 — Parallel master port data 11 |
| ピン 33 | PMD12 — Parallel master port data 12 |
| ピン 34 | PMD13 — Parallel master port data 13 |
| ピン 35 | PMD14 — Parallel master port data 14 |
| ピン 36 | PMD15 — Parallel master port data 15 |
| ピン 37 | PMRD — Parallel master port read strobe |
| ピン 38 | PMWR — Parallel master port write strobe |
| ピン 39 | VSS — Ground |
| ピン 40 | VDD — Positive supply |
| ピン 41 | RD11 — General purpose I/O |
| ピン 42 | RD10 — General purpose I/O |
| ピン 43 | RD9 — General purpose I/O |
| ピン 44 | RD8 — General purpose I/O |
| ピン 45 | RB15 — General purpose I/O / OC1 |
| ピン 46 | RB14 — General purpose I/O / OC2 |
| ピン 47 | RB13 — General purpose I/O / OC3 |
| ピン 48 | RB12 — General purpose I/O / OC4 |
| ピン 49 | RB11 — General purpose I/O / OC5 |
| ピン 50 | RB10 — General purpose I/O |
| ピン 51 | RB9 — General purpose I/O |
| ピン 52 | RB8 — General purpose I/O |
| ピン 53 | RB7 — General purpose I/O |
| ピン 54 | RB6 — General purpose I/O |
| ピン 55 | RB5 — General purpose I/O / AN5 |
| ピン 56 | RB4 — General purpose I/O / AN4 |
| ピン 57 | RB3 — General purpose I/O / AN3 |
| ピン 58 | RB2 — General purpose I/O / AN2 |
| ピン 59 | RB1 — General purpose I/O / AN1 |
| ピン 60 | RB0 — General purpose I/O / AN0 |
| ピン 61 | VSS — Ground |
| ピン 62 | VDD — Positive supply |
| ピン 63 | RD7 — General purpose I/O |
| ピン 64 | RD6 — General purpose I/O |
| ピン 65 | RD5 — General purpose I/O |
| ピン 66 | RD4 — General purpose I/O |
| ピン 67 | RC15 — General purpose I/O / OC1 |
| ピン 68 | RC14 — General purpose I/O / OC2 |
| ピン 69 | RC13 — General purpose I/O / OC3 |
| ピン 70 | RC12 — General purpose I/O / OC4 |
| ピン 71 | RC11 — General purpose I/O / OC5 |
| ピン 72 | VSS — Ground |
| ピン 73 | VDD — Positive supply |
| ピン 74 | RC10 — General purpose I/O |
| ピン 75 | RC9 — General purpose I/O |
| ピン 76 | RC8 — General purpose I/O |
| ピン 77 | RC7 — General purpose I/O |
| ピン 78 | RC6 — General purpose I/O |
| ピン 79 | RC5 — General purpose I/O |
| ピン 80 | RC4 — General purpose I/O |
| ピン 81 | RC3 — General purpose I/O |
| ピン 82 | RC2 — General purpose I/O |
| ピン 83 | RC1 — General purpose I/O |
| ピン 84 | RC0 — General purpose I/O |
| ピン 85 | RD3 — General purpose I/O |
| ピン 86 | RD2 — General purpose I/O |
| ピン 87 | RD1 — General purpose I/O |
| ピン 88 | RD0 — General purpose I/O |
| ピン 89 | RA15 — General purpose I/O |
| ピン 90 | VSS — Ground |
| ピン 91 | VDD — Positive supply |
| ピン 92 | OSC2 — Oscillator output / CLKO |
| ピン 93 | OSC1 — Oscillator input / CLKI |
| ピン 94 | RA14 — General purpose I/O |
| ピン 95 | RA10 — General purpose I/O |
| ピン 96 | RA9 — General purpose I/O |
| ピン 97 | RA8 — General purpose I/O |
| ピン 98 | TCK — JTAG test clock |
| ピン 99 | TMS — JTAG test mode select |
| ピン 100 | TDI — JTAG test data in |
主な用途
PIC32MX564F064L-I/PT の用途: 6 件s: Industrial CAN-to-USB Gateway, USB Data Acquisition Module, Automotive Body Control Module, Point-of-Sale (POS) Terminal, Industrial Sensor Hub with CAN, HMI / Operator Panel.
Industrial CAN-to-USB Gateway
The PIC32MX564F064L-I/PT's integrated CAN 2.0B and USB 2.0 Full-Speed make it a natural choice for industrial bridges that translate CAN bus traffic to USB HID or CDC for host PCs. Its 80 MHz MIPS32 M4K core can parse 1 Mbit/s CAN frames and forward them at 12 Mbit/s USB Full-Speed without bottlenecking. The four DMA channels keep USB endpoint RAM and CAN message RAM moving autonomously, leaving the CPU free for protocol handling. With 53 GPIO, designers also have headroom for status LEDs and digital I/O. Industrial -40C to +85C operation covers most factory cabinets.
おすすめ
USB Data Acquisition Module
The PIC32MX564F064L-I/PT is well matched to USB-attached DAQ front ends: its 10-bit 1 Msps ADC (up to 16 channels) feeds data into DMA buffers while the USB endpoint autonomously transmits samples to the host. The 32 KB SRAM buffers several thousand samples between USB transactions. 80 MHz of CPU performance runs any calibration or DSP filtering without dropping samples. The 2.3-3.6 V range is conveniently compatible with USB VBUS-derived supplies.
おすすめ
Automotive Body Control Module
Inside a vehicle body controller, the PIC32MX564F064L-I/PT drives window lifters, mirror adjusters, seat motors, and LED lighting via PWM timers. Five 16-bit timers generate up to 20 PWM channels at 80 MHz, and the CAN 2.0B module links the BCM to the vehicle CAN bus. While the I-suffix part stops at +85C (under-hood requires the -V or HT variant), it remains suitable for cabin-only modules. The 53 GPIO handle most BCM sensor and actuator counts without an I/O expander.
おすすめ
Point-of-Sale (POS) Terminal
POS terminals need USB device connectivity, secure key input, and a small color or character LCD - all of which the PIC32MX564F064L-I/PT delivers. The integrated USB 2.0 Full-Speed controller handles barcode scanners, receipt printers, and magnetic-stripe readers without external PHY. The PMP (Parallel Master Port) drives a character LCD directly, while 53 GPIO service the keypad matrix. 32 KB SRAM is ample for transaction buffering; 64 KB Flash fits firmware and a small font table.
おすすめ
Industrial Sensor Hub with CAN
For multi-sensor nodes that aggregate temperature, pressure, and flow data onto a CAN bus, the PIC32MX564F064L-I/PT combines four DMA channels, two SPI/I2C ports, and the CAN 2.0B controller. Its 16 ADC channels read out sensor signals at 1 Msps aggregate. The wide 2.3-3.6 V supply range accepts 3.3 V or 5 V sensor busses via simple level shifters. Industrial -40C to +85C operation covers most installations.
おすすめ
HMI / Operator Panel
HMI panels combine a graphic or character LCD, keypad, LEDs, and a USB or CAN host link. The PIC32MX564F064L-I/PT's PMP/EPMP drives STN/TFT panels at up to 80 MHz pixel clock, while 53 GPIO service a 4x4 keypad matrix and indicator LEDs. The 32 KB SRAM stores frame buffers, and 64 KB Flash holds the display list. USB and CAN provide connectivity to a master controller. Industrial temperature rating suits factory cabinets.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: PIC32MX564F064L-I/PT — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | PIC32MX564F064HT-I/PT | PIC32MX564F064L-V/PT | PIC32MX564F064LT-I/PT | PIC32MX534F064L-I/PT | PIC32MX564F064L-I/BG |
|---|---|---|---|---|---|---|
| Package | TQFP-100 (PT) 12x12 mm | TQFP-100 (PT) 12x12 mm - same | TQFP-100 (PT) 12x12 mm - same | TQFP-100 (PT) 12x12 mm - same | TQFP-100 (PT) 12x12 mm - same | LQFP-100 (BG) 14x14 mm - larger |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash | 64 KB | 256 KB | 64 KB | 64 KB | 64 KB | 64 KB |
| SRAM | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB |
| USB 2.0 | Full-Speed Device/Host/OTG | Full-Speed Device/Host/OTG | Full-Speed Device/Host/OTG | Full-Speed Device/Host/OTG | Not present | Full-Speed Device/Host/OTG |
| CAN 2.0B | Yes | Yes | Yes | Yes | Not present | Yes |
| CPU Speed | 80 MHz | 80 MHz | 80 MHz | 80 MHz | 80 MHz | 80 MHz |
| DMA Channels | 4 | 4 | 4 | 4 | 4 | 4 |
| Operating Temperature | -40C to +85C (Industrial) | -40C to +125C (Extended) | -40C to +105C (V-grade) | -40C to +85C (Industrial) | -40C to +85C (Industrial) | -40C to +85C (Industrial) |
| Approx. Qty-100 Price (USD) | 6.05 | 9.20 | 8.30 | 6.05 | 5.50 | 6.10 |
主な差別化要因
- Only same-Family part with combined USB 2.0 + CAN 2.0B （vs PIC32MX534F064L-I/PT)
- Available in 256 KB Flash variant with same pinout （vs PIC32MX564F064HT-I/PT)
- Industrial vs extended temperature grade options （vs PIC32MX564F064L-V/PT)
設計ノート
Place a 0.1 uF X7R decoupling capacitor within 5 mm of every VDD pin and a 10 uF bulk tantalum or ceramic on the main 3.3 V rail. The PIC32MX564F064L-I/PT has 7 VDD pins distributed around the 100-pin TQFP perimeter; missing any of them can cause intermittent brown-out resets during USB enumeration. For USB applications, add a 0.01 uF cap on VUSB (USB transceiver supply) and keep the ground return as short and direct as possible.
Estimated: at 80 MHz system clock, trace lengths on USB DP/DM must be matched within 1 mm and routed as a 90 ohm differential pair with continuous reference plane. The internal 8 MHz oscillator plus PLL provides the system clock, but for USB Full-Speed accuracy (48 MHz USB clock) the PLL requires a 4 MHz or 8 MHz crystal input; the 1% accuracy target makes an external crystal preferable to the internal 8 MHz RC oscillator.
Do not connect unused I/O pins directly to ground - leave them as outputs driving low or configure as inputs with weak pull-ups enabled. Forgetting to disable JTAG on pins 98-100 (TCK/TMS/TDI/TDO) when using ICSP only will cause those four pins to consume additional current. Also, the boot configuration bits must be set for USB (or non-USB) operation; otherwise the part may hang at reset. Refer to section 32 (Configuration Bits) of DS61143 before locking the part.
Estimated: at 80 MHz and 3.3 V, the active current is approximately 88 mA (1.1 mA/MHz x 80 MHz), dissipating ~290 mW. The TQFP-100 package has a theta_JA of approximately 50 C/W on a 4-layer JEDEC test board, yielding a junction temperature rise of ~14.5C above ambient. Industrial -40C to +85C operation is comfortably met without special thermal management.
コンプライアンス情報
RoHS and REACH compliant per Microchip material declarations. Not AEC-Q100 qualified - the standard PIC32MX564 family targets industrial/commercial use; for AEC-Q100 automotive applications, designers typically move to PIC32MX1xx/2xx automotive variants. Lead-free matte-tin finish on /PT package.
