PIC32MX675F512HT-80I/PT - 80MHz, 512KB Flash MCU | Microchip
部品番号: PIC32MX675F512HT-80I/PT ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $12.95 | $12.95 |
| 10 | $11.78 | $117.80 |
| 100 | $10.45 | $1,045.00 |
| 500 | $9.32 | $4,660.00 |
| 1,000 | $8.27 | $8,270.00 |
PIC32MX675F512HT-80I/PT 概要
A 32-bit microcontroller (MCU) is a microprocessor core integrated with program memory (Flash), data memory (SRAM), and peripherals (UART, SPI, I2C, timers, ADC, communication controllers) on a single chip. The PIC32MX family is positioned in the hierarchy as follows: PIC32MX -> 32-bit MCU -> microcontroller -> embedded processor -> semiconductor. Microchip's PIC32MX6xx/7xx sub-family specifically targets connectivity applications by integrating Ethernet and USB on-chip, eliminating the need for external controllers and reducing BOM and board area.
Key features of the PIC32MX675F512HT-80I/PT include an integrated 10/100 Mbit Ethernet MAC with RMII/MII PHY interface, USB 2.0 full-speed OTG, 16-channel 10-bit 1 Msps ADC, five 16-bit timers/counters, four UART, three SPI, two I2C, and 53 general-purpose I/O pins. The 80 MHz core delivers 1.56 DMIPS/MHz, supporting DSP extensions for signal-processing workloads.
The PIC32MX6xx architecture uses a 5-stage pipeline Harvard core with hardware multiply/divide and DSP ASE, allowing deterministic interrupt response and efficient C-language execution. The wide peripheral set and dual connectivity (Ethernet + USB) make it well suited for IoT gateways and industrial control where multiple communication interfaces are required.
Typical applications include industrial IoT gateways, USB-enabled embedded devices, Ethernet-attached sensor hubs, HMI touch panels, and consumer electronics with web configuration interfaces. The 512 KB Flash supports over-the-air (OTA) firmware updates with room for dual-image bootloaders.
When designing with this MCU, allocate at least 64 KB of Flash for the MPLAB Harmony framework if Ethernet/USB stacks are enabled. Use the integrated PHY clock to free an oscillator pin and add an external 25 MHz crystal directly between OSC1/OSC2 with appropriate load capacitors for Ethernet operation.
ドロップイン代替品: PIC32MX675F512HT-80I/PT — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: PIC32MX675F512HT-80I/PT （同一形状・フットプリント） — 相違点: Package, ADC, Timers, Operating Temperature, Core Architecture.
クイック比較ツール — 並列比較する代替部品を選択:
PIC32MX675F512H-80I/PT
✅ ドロップイン✓ 在庫あり
$8.42 / 個
データシートを見る →PIC32MX675F512HT-80I/MR
✅ ドロップイン✓ 在庫あり
$6.45 / 個
データシートを見る →PIC32MX575F512H-80I/PT
✅ ドロップイン✓ 在庫あり
$5.11 / 個
データシートを見る →PIC32MX675F256H-80I/PT
✅ ドロップイン📋 参考代替品（カタログ未掲載）
PIC32MX460F512LT-80I/PT
✅ ドロップイン✓ 在庫あり
$6.85 / 個
データシートを見る →PIC32MX675F512HT-80I/PT 最大定格＆電気的特性
| Core Architecture | MIPS32 M4K 32-bit RISC |
| Maximum CPU Frequency | 80 MHz |
| Program Memory (Flash) | 512 KB (512K x 8) |
| Data Memory (SRAM) | 128 KB |
| Auxiliary RAM | 64 KB |
| 電源電圧 | 2.3 V to 3.6 V |
| I/O Pins | 53 |
| パッケージ | 64-TQFP (10 x 10 mm) |
| Ethernet MAC | 10/100 Mbit integrated |
| USB Controller | USB 2.0 Full-Speed Host/Device/OTG |
| ADC | 10-bit, 16-channel, 1 Msps |
| 動作温度 | -40 C to +85 C (industrial) |
| 実装タイプ | Surface Mount |
| MSLレベル | 3 (168 hours) |
| Lead-Free / RoHS | Lead-free, RoHS compliant |
PIC32MX675F512HT-80I/PT 64-tqfp (10 x 10 mm) ピン配置ガイド
PIC32MX675F512HT-80I/PT (64-tqfp (10 x 10 mm) パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: PIC32MX675F512HT-80I/PT.
詳細は データシート をご参照ください。
主な用途
PIC32MX675F512HT-80I/PT の用途: 6 件s: Industrial IoT Gateway, USB-Enabled Embedded Device, Ethernet-Attached Sensor Hub, HMI Touch Panel Controller, Consumer Web-Configuration Device, Motor Control Front-End.
Industrial IoT Gateway
The PIC32MX675F512HT-80I/PT fits industrial IoT gateways thanks to its integrated 10/100 Ethernet MAC and USB 2.0 OTG, which eliminate external connectivity ICs. The 80 MHz MIPS M4K core runs the MPLAB Harmony TCP/IP stack with 124 DMIPS throughput, while 512 KB Flash holds the full Harmony framework plus application logic with room for OTA dual-image bootloaders. The 128 KB SRAM plus 64 KB auxiliary buffer RAM is sufficient for concurrent Ethernet, USB, and Modbus TCP workloads. Operating from 2.3 V to 3.6 V at -40 C to +85 C, it tolerates industrial supply rails and ambient temperatures without derating.
おすすめ
USB-Enabled Embedded Device
For USB peripherals such as HID controllers, data loggers, and CDC devices, the PIC32MX675F512HT-80I/PT provides USB 2.0 Full-Speed Host/Device/OTG directly on-chip. The 53 I/O pins drive user-interface buttons and LED indicators, while the 10-bit 1 Msps ADC samples analog sensors at high rate. Compared to PIC32MX5xx parts, this device adds the Ethernet MAC, but for USB-only designs the larger 512 KB Flash accommodates composite USB stacks plus vendor-specific class firmware in a single image.
おすすめ
Ethernet-Attached Sensor Hub
Sensor hubs that aggregate Modbus, analog, and digital I/O over Ethernet benefit from the PIC32MX675F512HT-80I/PT's 10/100 Ethernet MAC paired with the 16-channel 10-bit ADC. The 80 MHz core runs the Harmony TCP/IP server stack with concurrent web server handling, while 512 KB Flash stores HTTP configuration pages, JSON telemetry templates, and the sensor driver library. Industrial -40 C to +85 C operation supports outdoor or factory-floor enclosures, and the 64-TQFP package provides easy hand-solder rework for low-volume industrial runs.
おすすめ
HMI Touch Panel Controller
The PIC32MX675F512HT-80I/PT's 80 MHz core and 53 I/O pins are well matched to small HMI panels with TFT displays, capacitive touch ICs, and rotary encoders. Its 128 KB main RAM holds double-buffered framebuffers for QVGA displays, and the 512 KB Flash accommodates LVGL or emWin graphics libraries. The USB OTG port enables firmware updates from a USB stick during field service - a common requirement for installed HMI panels that lack Ethernet access.
おすすめ
Consumer Web-Configuration Device
Consumer products with embedded web configuration (printers, IP cameras, smart appliances) leverage the PIC32MX675F512HT-80I/PT's integrated Ethernet MAC plus USB 2.0 to provide both wired and USB interfaces without external controllers. The 80 MHz MIPS M4K core executes the Harmony HTTP server with AJAX-style configuration pages, while 512 KB Flash holds HTML assets and embedded JavaScript. The 2.3 V to 3.6 V supply range lets designers reuse the same MCU across 3.3 V-only and wide-tolerance 5 V USB-powered variants.
おすすめ
Motor Control Front-End
Although the PIC32MX675F512HT-80I/PT lacks dedicated motor-control PWMs, it serves as an Ethernet-connected supervisory front-end for industrial motor drives. It reads encoder feedback via SPI or quadrature input, monitors motor current via the 16-channel ADC, and reports status over Modbus TCP. Its -40 C to +85 C industrial temperature range and 2.3 V to 3.6 V supply let it mount adjacent to power stages with appropriate isolation.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: PIC32MX675F512HT-80I/PT — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | PIC32MX675F512H-80I/PT | PIC32MX675F512HT-80I/MR | PIC32MX575F512H-80I/PT | PIC32MX675F256H-80I/PT | PIC32MX460F512LT-80I/PT |
|---|---|---|---|---|---|---|
| Package | 64-TQFP (PT) 10x10 mm | 64-TQFP (PT) 10x10 mm - same | 64-QFN (MR) 9x9 mm - different | 64-TQFP (PT) 10x10 mm - same | 64-TQFP (PT) 10x10 mm - same | 64-TQFP (PT) 10x10 mm - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core / Max Frequency | MIPS32 M4K / 80 MHz | MIPS32 M4K / 80 MHz | MIPS32 M4K / 80 MHz | MIPS32 M4K / 80 MHz | MIPS32 M4K / 80 MHz | MIPS32 M4K / 80 MHz |
| Flash Memory | 512 KB | 512 KB | 512 KB | 512 KB | 256 KB (-50%) | 512 KB |
| SRAM | 128 KB + 64 KB aux | 128 KB + 64 KB aux | 128 KB + 64 KB aux | 128 KB + 64 KB aux | 64 KB + 64 KB aux (-50%) | 128 KB + 0 aux |
| Ethernet MAC | 10/100 integrated | 10/100 integrated | 10/100 integrated | Not present | 10/100 integrated | Not present |
| USB Controller | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG |
| I/O Pins | 53 | 53 | 53 | 53 | 53 | 53 |
| Supply Voltage | 2.3 V to 3.6 V | 2.3 V to 3.6 V | 2.3 V to 3.6 V | 2.3 V to 3.6 V | 2.3 V to 3.6 V | 2.3 V to 3.6 V |
| Operating Temperature | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
| Lifecycle Status | Active | Active | Active | Active | Active | Active |
主な差別化要因
- Integrated Ethernet MAC plus USB 2.0 OTG on the same die （vs PIC32MX575F512H-80I/PT)
- Doubled program memory versus the lower-cost variant （vs PIC32MX675F256H-80I/PT)
- 64 KB extra auxiliary RAM for Ethernet/USB packet buffers （vs PIC32MX460F512LT-80I/PT)
- Same silicon and identical die layout （vs PIC32MX675F512H-80I/PT)
設計ノート
The PIC32MX675F512HT-80I/PT 64-TQFP package requires a small PCB footprint but is hand-solderable with proper pad design. Provide a solid ground plane on the top layer directly under the device and stitch vias at 5 mm spacing around the perimeter to reduce EMI on the 80 MHz core clock. The 10x10 mm body allows compact routing but the inner-pin escape must use microvias or thin traces (4 mil/0.1 mm) to fan out all 53 I/O. Place the 25 MHz Ethernet PHY crystal within 5 mm of OSC1/OSC2 and guard-trace both signals to ground per the PIC32MX5XX/6XX/7XX family datasheet layout recommendations.
Estimated: The PIC32MX675F512HT-80I/PT active supply current at 80 MHz with Ethernet + USB active is approximately 80 mA typical, plus PHY and USB transceiver draw. Total 3.3 V rail budget should be at least 200 mA with 10 percent margin. Use a low-noise LDO (e.g., Microchip MCP1700 or MIC29150) followed by a ferrite bead and 10 uF ceramic + 100 nF decoupling at each VDD/VSS pair. Place 100 nF capacitors within 3 mm of every VDD pin; the 64-TQFP has multiple VDD pins that must each be decoupled independently to prevent logic-level glitches under high-speed switching.
Do not confuse the PIC32MX675F512HT-80I/PT (64-TQFP, tape-and-reel) with the PIC32MX675F512HT-80I/MR (64-QFN). Both share silicon but the QFN land pattern is not pin-compatible with the TQFP; using one footprint for the other will short adjacent pins. Also, the '675' sub-family has integrated Ethernet - do not waste PCB area routing an external MAC. Finally, do not exceed 80 MHz instantaneous needs convert the '80I' suffix to '80V' for 5 V-tolerant variants. Validate the temperature grade: 'I' = -40 C to +85 C industrial, not -40 C to +125 C extended.
The integrated Ethernet MAC uses RMII or MII to an external PHY; route the 50 MHz RMII clock as a length-matched group and keep RMII traces under 50 mm with 50 ohm characteristic impedance on a 4-layer stackup. For USB, the 12 MHz Full-Speed clock and DP/DM differential pair must be 90 ohm differential and length-matched within 150 mil (3.8 mm). Place common-mode chokes on DP/DM if the device is near switching noise sources. Keep the 25 MHz PHY crystal traces short and symmetric; ground the can to reduce radiated emissions.
コンプライアンス情報
RoHS and lead-free confirmed per Microchip product page and DigiKey listing. AEC-Q100 is not applicable for industrial-grade MCUs; automotive designs should use PIC32MX variants with explicit 'AEC-Q100' marking. Halogen-free status not specified in distributor data - consult Microchip environmental compliance documentation.
