S9S12XS128J1MAE - 16-bit S12X MCU, 128KB Flash, 40MHz | NXP
部品番号: S9S12XS128J1MAE ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $4.26 | $4.26 |
| 10 | $3.95 | $39.50 |
| 100 | $3.62 | $362.00 |
| 500 | $3.28 | $1,640.00 |
| 1,000 | $2.97 | $2,970.00 |
S9S12XS128J1MAE 概要
An MCU (microcontroller unit) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash), working memory (RAM), and a rich set of peripherals such as timers, ADC, communication controllers, and general-purpose I/O. In the embedded hierarchy, the S12XS family sits within the 16-bit automotive MCU tier (16-bit MCU -> HCS12 family -> S12XS sub-family -> automotive body controller) - typically chosen for cost-sensitive body and chassis modules where 32-bit performance is not required but robust automotive qualification is.
Key features include 128 KB on-chip Flash (organized as 128K x 8), 8 KB RAM, 44 GPIO lines, and an integrated CAN (MSCAN) controller, multiple SCI/SPI interfaces, a 10/12-bit ADC, and PWM channels for motor and lighting control. The device operates from a 5 V supply and supports background-debug mode (BDM) for in-circuit programming and debug.
The S12XS architecture pairs the main CPU with the XGATE co-processor, a programmable RISC engine that offloads interrupt-driven peripheral servicing. This dual-core approach gives the S9S12XS128J1MAE deterministic I/O response under heavy interrupt load, which is critical for CAN/LIN body networks where missed frames can trigger UDS DTCs. The Flash is split into independent partitions to support EEPROM emulation and bootloader coexistence.
Typical applications include automotive body controllers (BCM), HVAC control modules, seat control units, instrument cluster sub-circuits, lighting ECUs, and CAN/LIN gateway nodes. The 64-LQFP footprint is shared across the S12XS family, enabling PCB reuse between derivatives with different Flash sizes.
Design considerations include providing a clean 5 V analog/digital supply, decoupling each VDD pin with 100 nF ceramics, reserving the BKGD pin for BDM access, and ensuring the reset pin has proper hold-time capacitor per the S12X reference manual.
This page consolidates distributor pricing, pin-compatible S12XS-family alternatives, and practical design notes that complement - not duplicate - the manufacturer datasheet.
ドロップイン代替品: S9S12XS128J1MAE — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: S9S12XS128J1MAE （同一形状・フットプリント） — 相違点: Operating Temperature, Package, Core, Mounting Style.
クイック比較ツール — 並列比較する代替部品を選択:
MC9S12XS128CAE
✅ ドロップイン📋 参考代替品（カタログ未掲載）
S9S12XS256J0VAL
✅ ドロップイン📋 参考代替品（カタログ未掲載）
S9S12G128AVLFR
✅ ドロップイン✓ 在庫あり
$6.78 / 個
データシートを見る →S9S12XS128J1CAE
✅ ドロップイン✓ 在庫あり
$5.55 / 個
データシートを見る →MC9S12XS256CAE
✅ ドロップイン✓ 在庫あり
$7.95 / 個
データシートを見る →S9S12XS128J1MAE 最大定格＆電気的特性
| Core | HCS12X (16-bit CISC with XGATE co-processor) |
| Program Memory (Flash) | 128 KB (128K x 8) |
| RAM | 8 KB |
| Maximum CPU Frequency | 40 MHz |
| Operating Voltage | 5 V (typical) |
| 動作温度 | -40C to +125C (Automotive Grade) |
| パッケージ | 64-LQFP (10x10 mm) |
| GPIO Count | 44 |
| Package Code | LFQFP / 64-LQFP |
| Terminal Form | GULL WING (SMT) |
| AEC-Q100 Qualification | Yes (Automotive Qualified) |
| On-chip CAN (MSCAN) | Yes |
| On-chip ADC | Yes (10/12-bit) |
| Debug Interface | BDM (Background Debug Mode) |
| 実装タイプ | Surface Mount |
S9S12XS128J1MAE ピン構成
| ピン 1 | XADDR19 — External address/data bus (mode-dependent) |
| ピン 2 | VDDR — Voltage regulator supply (5 V) |
| ピン 3 | VDD — Digital supply (5 V) |
| ピン 4 | VSS — Digital ground |
| ピン 5 | BKGD — Background Debug Mode pin |
| ピン 6 | RESET — Reset input (active low) |
| ピン 7 | TEST — Test mode (tie to VSS in normal operation) |
| ピン 8 | PAD0 — External bus / ATD channel |
| ピン 9 | PAD1 — External bus / ATD channel |
| ピン 10 | PAD2 — External bus / ATD channel |
| ピン 11 | PAD3 — External bus / ATD channel |
| ピン 12 | PAD4 — External bus / ATD channel |
| ピン 13 | PAD5 — External bus / ATD channel |
| ピン 14 | PAD6 — External bus / ATD channel |
| ピン 15 | PAD7 — External bus / ATD channel |
| ピン 16 | VDDA — Analog supply (5 V) |
| ピン 17 | VSSA — Analog ground |
| ピン 18 | AN0_PAD08 — ADC analog input / GPIO |
| ピン 19 | AN1_PAD09 — ADC analog input / GPIO |
| ピン 20 | AN2_PAD10 — ADC analog input / GPIO |
| ピン 21 | AN3_PAD11 — ADC analog input / GPIO |
| ピン 22 | AN4_PAD12 — ADC analog input / GPIO |
| ピン 23 | AN5_PAD13 — ADC analog input / GPIO |
| ピン 24 | AN6_PAD14 — ADC analog input / GPIO |
| ピン 25 | AN7_PAD15 — ADC analog input / GPIO |
| ピン 26 | PWM0 — Pulse-width modulation channel 0 |
| ピン 27 | PWM1 — Pulse-width modulation channel 1 |
| ピン 28 | PWM2 — Pulse-width modulation channel 2 |
| ピン 29 | PWM3 — Pulse-width modulation channel 3 |
| ピン 30 | PWM4 — Pulse-width modulation channel 4 |
| ピン 31 | PWM5 — Pulse-width modulation channel 5 |
| ピン 32 | PWM6 — Pulse-width modulation channel 6 |
| ピン 33 | PWM7 — Pulse-width modulation channel 7 |
| ピン 34 | TxCAN — MSCAN transmit output |
| ピン 35 | RxCAN — MSCAN receive input |
| ピン 36 | PS0 — Port S bit 0 (GPIO/SCI) |
| ピン 37 | PS1 — Port S bit 1 (GPIO/SCI) |
| ピン 38 | PS2 — Port S bit 2 (GPIO/SPI) |
| ピン 39 | PS3 — Port S bit 3 (GPIO/SPI) |
| ピン 40 | PT0 — Port T bit 0 (timer/GPIO) |
| ピン 41 | PT1 — Port T bit 1 (timer/GPIO) |
| ピン 42 | PT2 — Port T bit 2 (timer/GPIO) |
| ピン 43 | PT3 — Port T bit 3 (timer/GPIO) |
| ピン 44 | PP0 — Port P bit 0 (GPIO/PWM) |
| ピン 45 | PP1 — Port P bit 1 (GPIO/PWM) |
| ピン 46 | PP2 — Port P bit 2 (GPIO/PWM) |
| ピン 47 | PP3 — Port P bit 3 (GPIO/PWM) |
| ピン 48 | PJ0 — Port J bit 0 (GPIO) |
| ピン 49 | PJ1 — Port J bit 1 (GPIO) |
| ピン 50 | PJ2 — Port J bit 2 (GPIO) |
| ピン 51 | PJ3 — Port J bit 3 (GPIO) |
| ピン 52 | PJ4 — Port J bit 4 (GPIO) |
| ピン 53 | PJ5 — Port J bit 5 (GPIO) |
| ピン 54 | PJ6 — Port J bit 6 (GPIO) |
| ピン 55 | PJ7 — Port J bit 7 (GPIO) |
| ピン 56 | PK0 — Port K bit 0 (GPIO) |
| ピン 57 | PK1 — Port K bit 1 (GPIO) |
| ピン 58 | PK2 — Port K bit 2 (GPIO) |
| ピン 59 | PK3 — Port K bit 3 (GPIO) |
| ピン 60 | VDDX — I/O supply (5 V) |
| ピン 61 | VSSX — I/O ground |
| ピン 62 | VPP — Flash programming voltage (tie to VDD in normal op) |
| ピン 63 | VDDF — Flash supply (5 V) |
| ピン 64 | VSSF — Flash ground |
主な用途
S9S12XS128J1MAE の用途: 7 件s: Automotive Body Control Module (BCM), HVAC Climate Control Module, Automotive Lighting ECU, Seat and Mirror Control Unit, CAN/LIN Gateway Node, Instrument Cluster Sub-Controller, Door Module and Window Lifter.
Automotive Body Control Module (BCM)
The S9S12XS128J1MAE is a natural fit for body control modules because it combines 128 KB Flash (enough for CAN/LIN stacks, OSEK OS, and diagnostic services), AEC-Q100 qualification, and the 64-LQFP footprint shared across the S12XS family. Its integrated MSCAN controller supports 1 Mbit/s CAN 2.0B frames typical of body networks. The XGATE co-processor offloads periodic CAN/LIN message servicing so the main CPU can run lighting, wiper, and central-locking logic without missing bus deadlines. Place the MCU next to the CAN transceiver with 100 nF decoupling on each VDD pin.
おすすめ
HVAC Climate Control Module
In HVAC climate modules, the S9S12XS128J1MAE drives BLDC fan motors via PWM channels, reads temperature sensors through its on-chip 10/12-bit ADC, and communicates with the BCM over CAN or LIN. The 40 MHz CPU provides ample headroom for PID control loops and sensor-fusion math, while 8 KB of RAM comfortably holds lookup tables for fan curves. AEC-Q100 qualification at +125C is essential because HVAC modules sit near the dashboard in direct sunlight.
おすすめ
Automotive Lighting ECU
Headlamp and tail-lamp ECUs use the S9S12XS128J1MAE to generate PWM dimming signals for LEDs, monitor current-sense feedback, and respond to LIN commands from the BCM. The MCU's multiple PWM channels and timer modules enable smooth fade-in/fade-out transitions required for daylight-running and animated turn-indicator patterns. 128 KB Flash accommodates adaptive-lighting firmware and OTA-bootloader space; 64-LQFP simplifies the high-current mixed-signal PCB layout.
おすすめ
Seat and Mirror Control Unit
Seat-position, mirror-adjust, and memory modules integrate 4-8 H-bridge motor channels and position sensors. The S9S12XS128J1MAE provides enough GPIO and PWM channels to drive all motors while running LIN slave communication to the BCM. AEC-Q100 +125C tolerance handles the under-seat thermal environment, and the XGATE co-processor keeps the LIN stack responsive while the main CPU manages motor control loops.
おすすめ
CAN/LIN Gateway Node
Gateway ECUs that bridge CAN and LIN sub-networks benefit from the S9S12XS128J1MAE's dual-bus capability: MSCAN for CAN 2.0B and SCI peripherals for LIN 2.x master/slave. 128 KB Flash holds routing tables, network-management stacks, and diagnostic UDS services. The deterministic XGATE-assisted interrupt handling prevents frame loss at high bus loads.
おすすめ
Instrument Cluster Sub-Controller
In distributed cluster architectures, the S9S12XS128J1MAE serves as a sub-controller driving stepper-motor gauge needles and segment-LCD backlights, while communicating with the main cluster processor over CAN. Its low 5 V supply current and PWM peripherals make it ideal for always-on dashboard sub-systems. The 64-LQFP package fits beneath the cluster housing without forcing expensive multi-layer PCB stack-ups.
おすすめ
Door Module and Window Lifter
Door modules with window lift, mirror fold, and puddle-lamp functions use the S9S12XS128J1MAE to integrate multiple LIN slaves, read anti-pinch current sensors, and drive relay/MOSFET outputs for the window motor. AEC-Q100 +125C qualification and 128 KB Flash handle ISO 7637-2 transient immunity plus LIN 2.x conformance stacks. The 44 GPIO count covers multi-channel motor control and lamp driving in a single MCU.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: S9S12XS128J1MAE — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MC9S12XS128CAE | S9S12XS256J0VAL | S9S12G128AVLFR | S9S12XS128J1CAE | MC9S12XS256CAE |
|---|---|---|---|---|---|---|
| Package | 64-LQFP (10x10 mm) | 64-LQFP (10x10 mm) - same | 64-LQFP - same | 64-LQFP - same | 64-LQFP - same | 64-LQFP - same |
| Brand | NXP Semiconductors | NXP Semiconductors (legacy Freescale) | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors (legacy Freescale) |
| Flash Memory | 128 KB | 128 KB - identical | 256 KB (+100%) | 128 KB - identical | 128 KB - identical | 256 KB (+100%) |
| RAM | 8 KB | 8 KB | 12 KB (+50%) | 8 KB | 8 KB | 12 KB (+50%) |
| Max CPU Frequency | 40 MHz | 40 MHz | 40 MHz | 25 MHz (G-series slower) | 40 MHz | 40 MHz |
| AEC-Q100 Qualified | Yes | Yes | Yes | Yes | Yes | Yes |
| GPIO Count | 44 | 44 | 44 | 44 | 44 | 44 |
| Operating Temperature | -40C to +125C | -40C to +125C | -40C to +125C | -40C to +125C | -40C to +125C | -40C to +125C |
主な差別化要因
- XGATE co-processor for deterministic interrupt handling （vs MC9S12XS128CAE)
- 128 KB Flash with 64-LQFP drop-in path to 256 KB （vs S9S12XS256J0VAL)
- AEC-Q100 +125C qualified 5 V automotive MCU （vs MC9S12G128AVLFR)
設計ノート
The S9S12XS128J1MAE requires a stable 5 V supply on VDD, VDDA, VDDX, and VDDF, each decoupled with a 100 nF X7R ceramic placed within 5 mm of the pin. The on-chip voltage regulator (VDDR/VSS) needs a bulk 4.7 uF-10 uF capacitor. Reverse-battery and load-dump protection (per ISO 7637-2) must be implemented externally with a TVS diode; the MCU itself does not survive >+18 V load-dump pulses. Estimated: at 40 MHz CPU + peripherals, the 5 V supply current is approximately 35-45 mA typical per the S12XS family data.
Route the BKGD and RESET traces away from switching nodes (PWM outputs, motor drivers) to avoid debug-mode lockups. Place the BDM connector at the board edge for production programming access. Use a guard ring around the analog pins (ANx_PADxx) tied to VSSA to reduce ADC noise pickup; the VSSA pin must return to a quiet ground island separate from digital VSS. Crystal or resonator traces to EXTAL/XTAL must be short and symmetric, with the load capacitors placed within 3 mm of the pins.
Do not leave the TEST pin floating - tie TEST directly to VSS per the S12X reference manual, or the device may enter test mode and fail to boot. Do not omit the VPP bypass capacitor (tie VPP to VDD with 100 nF in normal operation; only driven high during factory Flash programming). The RESET pin requires a 4.7 kohm pull-up to VDDX and a 1 nF capacitor to VSSX to meet the minimum reset pulse width - using only a capacitor can cause intermittent brown-out resets under engine-crank conditions. Finally, do not program the Flash across multi-sector boundaries without bank-erase alignment; doing so corrupts the EEPROM-emulation data.
コンプライアンス情報
AEC-Q100 qualified per NXP product page (Automotive Grade, -40C to +125C). RoHS/REACH status not explicitly stated in the verified web data and should be confirmed against the latest NXP material composition declaration before use in RoHS-mandated regions.