SIM7600G-H - LTE Cat-4 150Mbps Global 4G GNSS Module | SIMCom
部品番号: SIM7600G-H ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $54.97 | $54.97 |
| 10 | $52.22 | $522.20 |
| 100 | $49.47 | $4,947.00 |
| 500 | $46.72 | $23,360.00 |
| 1,000 | $43.98 | $43,980.00 |
SIM7600G-H 概要
A cellular module is a self-contained wireless modem that integrates baseband processor, RF transceiver, memory, and power management into a single land-grid-array unit. Within the wireless hierarchy it sits above discrete RF chipsets and below full gateways: host systems (MCU, SBC, or PC) talk to it over USB or UART using AT commands, while the module handles protocol stacks for LTE, WCDMA, and GSM internally.
Key features include true global band coverage across LTE-FDD, LTE-TDD, WCDMA/HSPA+, EDGE, and GPRS, so a single PCB design ships to any region. The integrated GNSS receiver with simultaneous cellular-plus-GNSS operation serves trackers and telematics. Interfaces span USB 2.0, UART, I2C, SDMMC, ADC, and PCM voice with DTMF, audio playback, and recording.
The module supports multiple built-in network protocols (TCP/IP, HTTP, FTP, MQTT-class stacks) and ships USB drivers for Windows, Linux, and Android, with a mainline Linux option in recent kernels. AT commands are compatible with the SIM7500/SIM7600 family, protecting software investment across variants.
Typical applications include vehicle telematics and fleet trackers, industrial IoT gateways, and Raspberry Pi or LattePanda 4G connectivity via popular HAT boards.
Critical design point: GSM burst emission draws up to 2 A ripple every 4.615 ms on the VBAT pins, so the supply must deliver more than 2 A with roughly 1000 uF bulk capacitance (or over 300 uF on a 2 A-capable rail) to keep voltage droop under 300 mV.
This page adds value beyond the datasheet by synthesizing distributor pricing, drop-in family alternatives, and practical power-supply design guidance in one place.
ドロップイン代替品: SIM7600G-H — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
クイック比較ツール — 並列比較する代替部品を選択:
SIM7600G R2
✅ ドロップイン📋 参考代替品（カタログ未掲載）
SIM7600E-H
✅ ドロップイン📋 参考代替品（カタログ未掲載）
SIM7600NA-H
✅ ドロップイン📋 参考代替品（カタログ未掲載）
SIM7600SA-H
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
SIM7600G-H R2
✅ ドロップイン📋 参考代替品（カタログ未掲載）
SIM7600G-H 仕様（メーカー公開）
| Technology | LTE Cat-4 / WCDMA / GSM (4G/3G/2G) |
| Downlink Data Rate | 150 Mbps (LTE Cat-4) |
| Uplink Data Rate | 50 Mbps (LTE Cat-4) |
| LTE Bands | LTE-FDD and LTE-TDD global bands |
| Frequency Bands (RF) | 850 MHz, 900 MHz, 1.8 GHz, 1.9 GHz |
| Fallback Networks | HSPA+, EDGE, GPRS, GSM |
| GNSS | GPS, BeiDou, GLONASS |
| Supply Voltage (VBAT) | 3.4 V to 4.2 V |
| Idle Current | 2.3 mA |
| Peak Current (GSM burst) | up to 2 A ripple |
| Interfaces | USB 2.0, UART, I2C, SDMMC, ADC, PCM |
| Voice Features | PCM voice, DTMF, audio playback and recording |
| Network Protocols | Multiple built-in (TCP/IP stack) |
| USB Driver Support | Windows, Linux, Android |
| AT Command Set | Compatible with SIM7500/SIM7600 series |
| Package Dimensions | 30 x 30 mm LCC, SMD |
| Antenna | External, not included |
| 実装タイプ | Surface Mount |
| RoHS ステータス | Compliant (per JLCPCB listing) |
SIM7600G-H インターフェースとコネクタ
SIM7600G-H は、メーカーが公開している以下のインターフェースとコネクタを備えています: 電力入力, USB。拡張ヘッダーのピン配置、コネクタのピン番号、電気的制限はメーカーのドキュメントで定義されています。
| 電力入力 | 3.4 V to 4.2 V |
| USB | Windows, Linux, Android |
詳細は メーカー資料 をご参照ください（拡張ヘッダーのピン配置とコネクタのピン番号の詳細）。
電力・熱特性
| 電力入力 | 3.4 V to 4.2 V |
メーカーが公開している SIM7600G-H の電力入力および熱パラメータ。
主な用途
SIM7600G-H の用途: 6 件s: Vehicle Telematics and Fleet Tracking, Industrial IoT Gateways, Raspberry Pi and SBC 4G Connectivity, Video Surveillance and Security Transmission, Smart Metering and Utility Communication, Portable Routers and Mobile Hotspots.
Vehicle Telematics and Fleet Tracking
The SIM7600G-H fits telematics because it combines LTE Cat-4 data (150 Mbps downlink) with integrated GPS, BeiDou, and GLONASS positioning in one module, eliminating a separate GNSS receiver and its antenna routing complexity. Typical designs connect the host MCU or SBC over UART/USB, pull position fixes continuously, and upload to fleet platforms via the module's built-in TCP/IP stack. Power design is the main constraint: the 2 A burst current on VBAT demands bulk capacitance near the module. The 2.3 mA idle current supports always-on trackers with modest battery budgets, and 2G/3G fallback preserves connectivity in weak-LTE rural areas.
おすすめ
Industrial IoT Gateways
Industrial gateways need reliable backhaul across regions, and the SIM7600G-H's global LTE-FDD/TDD plus WCDMA/GSM coverage means one BOM ships worldwide without regional variants. The 150 Mbps downlink handles Modbus-to-MQTT aggregation, video snapshots from site cameras, and OTA firmware distribution. Its built-in network protocols (TCP/IP, HTTP, FTP) offload the host processor, while USB 2.0 provides a high-throughput path to Linux-based gateways with mainline kernel drivers. Designers should provision a 2 A-capable VBAT rail with 300-1000 uF of capacitance, and use the I2C/ADC pins for auxiliary sensing tasks within the same module footprint.
おすすめ
Raspberry Pi and SBC 4G Connectivity
The SIM7600G-H is the standard module inside popular Waveshare and DFRobot 4G HATs for Raspberry Pi and LattePanda, functioning as a 4G network card. USB enumeration with mainline Linux kernel drivers makes setup nearly plug-and-play: the module appears as a modem supporting qmi_wwan/PPP and GNSS NMEA output. This suits remote monitoring stations, digital signage, and mobile robotics that need internet beyond Wi-Fi range. The host supplies power through the HAT; verify the 5 V input can source the 2 A burst demand. DFRobot documentation confirms compatibility with Arduino-based hosts over UART as well, using the shared SIM7500/SIM7600 AT command set.
おすすめ
Video Surveillance and Security Transmission
Battery- or solar-powered security cameras and NVR uplinks benefit from the SIM7600G-H's 50 Mbps uplink, sufficient for streaming compressed video from remote sites without fiber or fixed broadband. The module's LTE Cat-4 throughput sustains multiple 1080p H.264/H.265 streams or rapid event-clip uploads, and HSPA+/EDGE fallback keeps alerts flowing where LTE coverage is marginal. Designers should budget the 2 A VBAT burst into solar/battery sizing and favor the USB interface for full throughput. PCM audio interfaces also enable two-way talkback functionality directly through the module without an external audio codec in simple designs.
おすすめ
Smart Metering and Utility Communication
Utility infrastructure often sits where wired backhaul is unavailable; the SIM7600G-H provides meter and RTU communication over LTE with 2G/3G fallback, important in regions where network transitions are still underway. The 2.3 mA idle current suits periodically-reporting devices, and the AT command set compatible with SIM7500/SIM7600 series means firmware reused across a utility's module fleet. Built-in protocols (TCP/IP, FTP) let a low-cost MCU push readings without a full TCP stack. For underground or shielded installations, plan external antenna placement carefully since the module has no onboard antenna and supports only external connections.
おすすめ
Portable Routers and Mobile Hotspots
Mobile Wi-Fi routers exploit the SIM7600G-H's Cat-4 speeds to share a cellular connection among several devices, with the module bridging LTE to the router's WAN side over USB RNDIS/NCM or QMI. The 150 Mbps downlink supports travel routers, in-vehicle internet, and temporary-site connectivity for events and construction. Global band coverage means one hardware SKU serves international travelers. Thermal design is modest but non-trivial: sustained Cat-4 traffic warms the 30 x 30 mm LCC, so provide ground-plane heat spreading. Voice features (PCM, DTMF) additionally enable fixed-wireless-phone products from the same platform.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: SIM7600G-H — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | SIM7600G R2 | SIM7600E-H | SIM7600NA-H | SIM7600SA-H |
|---|---|---|---|---|---|
| Brand | SIMCom Wireless Solutions | SIMCom Wireless Solutions | SIMCom Wireless Solutions | SIMCom Wireless Solutions | SIMCom Wireless Solutions |
| Package | 30 x 30 mm LCC, SMD | 30 x 30 mm LCC - same | 30 x 30 mm LCC - same | 30 x 30 mm LCC - same | 30 x 30 mm LCC - same |
| LTE Class | Cat-4 (150/50 Mbps) | Cat-4 | Cat-4 | Cat-4 | Cat-4 |
| Band Coverage | Global (850/900/1800/1900 MHz + LTE-FDD/TDD) | Global | EMEA-optimized | North America | South America/Oceania |
| GNSS | GPS, BeiDou, GLONASS integrated | GPS, BeiDou, GLONASS | GPS, BeiDou, GLONASS | GPS, GLONASS | GPS, GLONASS |
| Fallback Networks | HSPA+, EDGE, GPRS | HSPA+, EDGE, GPRS | HSPA+, EDGE, GPRS | HSPA+, EDGE, GPRS | HSPA+, EDGE, GPRS |
| Supply Voltage | 3.4 V to 4.2 V | 3.4 V to 4.2 V | 3.4 V to 4.2 V | 3.4 V to 4.2 V | 3.4 V to 4.2 V |
| AT Command Compatibility | SIM7500/SIM7600 series | SIM7500/SIM7600 series | SIM7500/SIM7600 series | SIM7500/SIM7600 series | SIM7500/SIM7600 series |
主な差別化要因
- Integrated multi-constellation GNSS in base configuration （vs SIM7600NA-H)
- Full Cat-4 throughput with 2G/3G fallback （vs A7670G-H)
- Shared hardware/AT ecosystem across variants （vs Quectel EC25-G)
設計ノート
VBAT supply design is the most common failure point. Per the SIM7600 Hardware Design guide, GSM emission bursts every 4.615 ms draw ripple up to 2 A on the four VBAT pads (pins 62/63 and 38/39). If the supply supports up to 2 A, use more than 300 uF of bulk capacitance; otherwise use roughly 1000 uF total to keep voltage droop under 300 mV. Add 0.1 uF/1 uF low-ESR MLCCs near the pads for high-frequency EMC performance. A buck converter rated 3 A output with good transient response is the recommended front end from a 5 V system rail.
The module is an LCC castellated package intended for SMD reflow. Lay out a keep-out under the module body; route the USB 2.0 differential pair with 90 ohm controlled impedance and length matching, and keep the antenna feed as a 50 ohm microstrip with pi-matching network pads reserved even when the antenna appears pre-matched. Provide solid ground plane pour beneath and around the module for both RF return path and heat spreading during sustained Cat-4 transmission.
Do not power the module from a generic USB port or 3.3 V rail - VBAT must stay within 3.4 V to 4.2 V, and undervoltage during transmit bursts causes spontaneous resets that look like firmware bugs. Additionally, MCU UART logic levels must match the module's interface voltage domain; direct connection to 5 V logic can damage the module. Finally, confirm R2 vs original hardware revision when sourcing replacements, since distributor listings (e.g., DigiKey) stock both as separate MPNs.
When using UART for control, keep traces under 10 cm and add series resistors (22-33 ohm) to damp ringing, since GSM bursts inject common-mode noise onto nearby wiring. For full 150 Mbps performance, prefer the USB interface; UART bandwidth caps practical throughput and is better reserved for AT control plus GNSS NMEA. Separate GNSS antenna feed from cellular antenna by at least 20 mm or use good isolation to prevent LTE TX desensitizing the GNSS receiver during simultaneous operation.
コンプライアンス情報
RoHS compliance stated on LCSC/JLCPCB listings for this MPN. REACH, lead-free, halogen-free, and conflict-minerals declarations not stated in provided data - request manufacturer compliance certificate.
