SN75183D - Dual Differential Line Driver | Texas Instruments
部品番号: SN75183D ✓ 生産中SN75183D 概要
A differential line driver is an interface IC that converts one-sided logic signals into complementary differential outputs. This differential signaling method reduces susceptibility to common-mode noise and supports reliable communication over balanced interconnects. Within the interface hierarchy, the SN75183D belongs to the line-driver class of logic interface ICs, alongside buffers, transceivers, and phase splitters.
The SN75183D provides four differential driver outputs arranged as two dual-output channels. Its TTL-compatible inputs allow ordinary TTL logic to control the drivers without additional level conversion. The output stages use high-current, totem-pole-like structures, making the device suitable for phase-splitting, TTL expansion, balanced-line transmission, and systems requiring two complementary outputs from each input.
According to the Texas Instruments SN75183 family documentation, the DS8830, SN55183, and SN75183 share the basic differential-driver architecture. The SN75183D is specified for a 0 to 70 °C operating-temperature range and uses a 14-pin SOIC package. These characteristics place it in a legacy interface family where PCB footprint compatibility and established TTL logic compatibility are important design considerations.
Typical applications include balanced twisted-pair data links, TTL bus expansion, clock and data phase splitting, industrial control interfaces, retrofits of established TTL systems, and point-to-point links where complementary drive currents improve signal integrity. In each case, the circuit must maintain compatible supply voltage, input logic levels, output loading, and termination requirements.
For a new design, check the supply-decoupling arrangement and route the differential pair as a tightly coupled pair. Confirm that the connected line impedance, connector return path, and receiver thresholds match the driver's output characteristics. The short-circuit and clamp features improve robustness, but they do not remove the need for correct board layout and external line protection.
This page consolidates the device's electrical characteristics, package information, drop-in family alternatives, application guidance, and practical PCB considerations into a design-focused reference. It also identifies where legacy temperature grade, package variant, and qualification differences matter when maintaining or redesigning an existing circuit.
ドロップイン代替品: SN75183D — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
SN75183N
✅ ドロップイン📋 参考代替品（カタログ未掲載）
SN75183DE4
✅ ドロップイン📋 参考代替品（カタログ未掲載）
SN55183D
✅ ドロップイン📋 参考代替品（カタログ未掲載）
DS8830D
✅ ドロップイン📋 参考代替品（カタログ未掲載）
SN75183D 仕様
| Product Type | Dual differential line driver |
| Differential Driver Channels | 2 channels |
| Output Drivers | 4 outputs |
| 電源電圧 | 5 V |
| Input Compatibility | TTL-compatible |
| Logic Output Modes | AND and NAND |
| Output Protection | Short-circuit protection |
| Transient Protection | Output clamp diodes |
| Output Stage | High-current totem-pole output |
| 動作温度範囲 | 0 °C to 70 °C |
| パッケージ | 14-pin SOIC (D) |
| 実装タイプ | Surface mount |
| Line Impedance Support | Normal line impedances |
| Signaling Mode | Differential and single-ended inputs |
SN75183D 14-pin soic (d) ピン配置ガイド
SN75183D (14-pin soic (d) パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: SN75183D.
詳細は データシート をご参照ください。
主な用途
SN75183D の用途: 6 件s: Balanced Twisted-Pair Data Links, TTL Logic Expansion, Clock and Data Phase Splitting, Industrial Point-to-Point Control, Legacy TTL System Retrofit, Long-Duration Balanced Instrumentation.
Balanced Twisted-Pair Data Links
The SN75183D fits balanced data links because it provides two differential driver channels, four high-current outputs, and operation from a single 5 V supply. According to the Texas Instruments SN75183 datasheet, the output stages can drive normal-impedance balanced lines such as twisted pair without excessive power dissipation. Place the device near the cable connector, route each differential pair together, and return the associated ground path carefully. The main design consideration is confirming that receiver thresholds, cable impedance, and line length remain compatible with the driven voltage and timing requirements.
おすすめ
TTL Logic Expansion
The SN75183D is suitable for TTL logic expansion because its inputs are TTL-compatible and its high-current totem-pole-like output stages can drive additional logic loads. The Texas Instruments SN75183 family documentation specifically identifies TTL expansion and phase splitting as supported uses. Each differential driver channel can provide complementary drive signals where the surrounding system needs both true and complement forms. Confirm fanout and load-current requirements for every connected gate, keep the supply return path compact, and avoid substituting a generic buffer whose input thresholds or output levels differ from those of the SN75183 family.
おすすめ
Clock and Data Phase Splitting
The SN75183D can generate complementary clock or data signals by using its differential driver channels in a phase-splitting arrangement. Its four high-current outputs provide the source drive needed when a downstream TTL device requires one signal and its inverse. According to the Texas Instruments SN75183 datasheet, the output stages resemble TTL totem-pole outputs, making the device appropriate for legacy phase-splitting systems. Place output branches symmetrically where possible, account for unequal load capacitance between complementary branches, and verify edge timing at the receiver rather than assuming perfect symmetry under all loading conditions.
おすすめ
Industrial Point-to-Point Control
The SN75183D can support short point-to-point control links that use 5 V TTL signaling and require complementary outputs. Its differential driver channels help separate signal transitions from common-mode noise on suitably routed wiring, while short-circuit protection and output clamp diodes add robustness around the driver stage. The 0 to 70 °C operating range makes the device appropriate for controlled indoor industrial equipment rather than unrestricted outdoor use. Validate the complete interface under worst-case cable length and load, provide local supply decoupling, and add external surge protection if the wiring leaves the equipment enclosure.
おすすめ
Legacy TTL System Retrofit
The SN75183D is a practical choice for maintaining a legacy TTL system because it combines a 5 V supply, TTL-compatible inputs, AND/NAND operating modes, and established 14-pin SOIC packaging. The Texas Instruments documentation groups the DS8830, SN55183, and SN75183 as related differential line drivers, which supports family-level planning for repair and redesign. Before replacing an installed device, compare the complete pin description, input logic levels, output states, and load current against the existing circuit. Preserve the original footprint and verify startup behavior, especially if unused input or output pins were previously tied differently.
おすすめ
Long-Duration Balanced Instrumentation
The SN75183D can drive balanced instrumentation lines when the circuit operates from 5 V and the selected line impedance is within the family’s intended range. Differential outputs reduce the effect of common-mode disturbance in a controlled measurement or communication path, while the high-current outputs provide useful drive capability for moderate capacitance and line loading. Keep the driver close to the connector to minimize added stub length, maintain a continuous ground reference, and observe the stated 0 to 70 °C range. Long cable runs still require receiver-side analysis for attenuation, reflections, and protection.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: SN75183D — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | SN75183N | SN75183DE4 | SN55183D | DS8830D |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-pin SOIC (D) | 14-pin SOIC (D) | 14-pin SOIC (D) | 14-pin SOIC (D) | 14-pin SOIC (D) |
| Product Type | Dual differential line driver | Dual differential line driver | Dual differential line driver | Dual differential line driver | Dual differential line driver |
| Differential Driver Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Output Drivers | 4 outputs | 4 outputs | 4 outputs | 4 outputs | 4 outputs |
| Input Compatibility | TTL-compatible | TTL-compatible | TTL-compatible | TTL-compatible | TTL-compatible |
| Logic Output Modes | AND and NAND | AND and NAND | AND and NAND | AND and NAND | AND and NAND |
主な差別化要因
- Provides a complete dual differential driver without receiver channels （vs SN75183N)
- Shares the established SN75183 family architecture （vs SN55183D)
- Offers an active lifecycle option for legacy interface designs （vs SN75183DE4)
- Supports differential drive, TTL expansion, and phase splitting in one device （vs DS8830D)
設計ノート
Place the SN75183D close to the line-driver connector and route each true-and-complement output as a tightly coupled differential pair. Avoid routing one branch through a different connector or test point while the other follows a direct path, because branch-length differences can distort edges and reduce common-mode noise rejection. Provide a continuous ground reference where the interface specification requires it, and keep switching or high-current traces physically separate from the driver outputs.
Use a low-impedance 5 V supply and place the recommended bypass capacitor at the device power and ground pins. The SN75183D uses high-current totem-pole-like outputs, so supply transients can accompany output transitions. Keep the supply-return path short, connect the bypass capacitor directly to the relevant pins, and avoid sharing a long return segment with unrelated digital loads. Confirm the selected capacitor and trace geometry against the manufacturer’s recommended application circuit.
Do not treat the SN75183 as a generic RS-485 or RS-422 transceiver without completing an interface-level review. The device is a differential line driver with TTL-compatible inputs, AND/NAND logic modes, and family-specific output characteristics. Before a redesign, compare every pin, input threshold, output level, output-current limit, and operating-temperature requirement. This prevents a package-compatible substitution from creating logic-state or receiver-threshold errors.
Maintain symmetry between complementary outputs and minimize unnecessary copper around high-switching nodes. If one output drives a longer PCB trace, connector lead, or heavier capacitive load than the other, its edge timing may diverge from the complementary channel. Use similar trace geometry and termination arrangements where practical, and validate the pair with an oscilloscope at the connector rather than relying only on simulation at the driver pins.
コンプライアンス情報
The SN75183D is a 0 to 70 °C commercial-temperature interface IC and is not identified as an AEC-Q100 automotive-qualified variant. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the manufacturer’s current product documentation.