TS954IN - 3MHz Quad Rail-to-Rail Op Amp | STMicroelectronics
部品番号: TS954IN ✓ 生産中TS954IN 概要
An operational amplifier is an active semiconductor device that amplifies the voltage difference between its differential inputs. Rail-to-rail input capability means the input common-mode range can extend toward both supply rails, while rail-to-rail output capability allows the output voltage to approach the operating limits more closely than a conventional non-rail-to-rail amplifier. The TS954IN belongs to the TS95x family of low-power BiCMOS operational amplifiers optimized for single-supply systems.
Key characteristics include four amplifier channels in one package, a 3 MHz gain-bandwidth product, and a 1 V/us slew rate. These specifications support applications such as sensor interfaces, buffered analog signals, low-voltage instrumentation, audio paths, and general-purpose analog conditioning. The TS954IN is also identified as ESD protected to 2 kV and includes latch-up protection according to the manufacturer datasheet information.
The BiCMOS architecture combines bipolar input characteristics with CMOS power-handling behavior. This implementation supports low-power operation while maintaining a useful small-signal bandwidth for sensor, filtering, and signal-buffer circuits. At a 3V supply, the family is specifically optimized for low-power consumption, which makes it relevant to portable equipment and embedded analog systems that cannot justify a higher-power precision amplifier.
Typical uses include buffering sensor outputs, amplifying low-level analog signals, active filtering, level shifting, audio preamplification, and instrumentation. The quad organization reduces package count when several independent analog channels are required. Designers should still evaluate input offset voltage, input bias current, output-current capability, noise, and stability for the exact gain, load, and supply conditions before finalizing a circuit.
The principal design consideration is operating margin. Rail-to-rail inputs and outputs do not remove the requirement to maintain adequate input and output voltage limits, especially under load. Decoupling capacitors should be placed close to the supply pins, and feedback networks should be designed to preserve the intended closed-loop gain while avoiding output saturation.
This product page combines the manufacturer family description with practical application guidance, parameter comparison, and pin-package considerations. It is intended to help engineers determine whether the TS954IN's four-channel 3V/5V rail-to-rail architecture fits a board-level design before consulting the complete manufacturer datasheet for limit values and test conditions.
ドロップイン代替品: TS954IN — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: TS954IN （同一形状・フットプリント） — 相違点: Package, Mounting Type, Slew Rate, ESD Protection, Input Common-Mode Range.
TS954ID
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →TS954IP
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
TS954IYDT
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
OP496GP
✅ ドロップイン📋 参考代替品（カタログ未掲載）
OP496GPZ
✅ ドロップイン📋 参考代替品（カタログ未掲載）
TS954IN 最大定格＆電気的特性
| Product Type | Quad input/output rail-to-rail low-power operational amplifier |
| Amplifier Channel Count | 4 circuits |
| Architecture | BiCMOS |
| Supply Optimization | 3 V and 5 V operation |
| Maximum Supply Voltage | 12 V |
| Gain-Bandwidth Product | 3 MHz |
| Slew Rate | 1 V/us |
| Supply Voltage Rejection Ratio | 80 dB |
| Input Common-Mode Range | Input rail-to-rail |
| Output Voltage Swing | Output rail-to-rail |
| ESD Protection | 2 kV |
| Latch-Up Protection | Supported |
| パッケージ | 14-DIP |
| 実装タイプ | Through-hole |
TS954IN 14-dip ピン配置ガイド
TS954IN (14-dip パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: TS954IN.
詳細は データシート をご参照ください。
主な用途
TS954IN の用途: 6 件s: Low-Voltage Sensor Conditioning, Portable Instrumentation, Active Filtering, Audio Preamplification, Data Acquisition Interfaces, General-Purpose Analog Buffering.
Low-Voltage Sensor Conditioning
The TS954IN suits low-voltage sensor front ends because its rail-to-rail input stage accepts signals approaching the 3V or 5V supply rails, while the 3 MHz gain-bandwidth product supports useful closed-loop bandwidth above low-frequency sensor signals. Each of the four channels can buffer or amplify a transducer output without requiring four separate packages. The 1 V/us slew rate provides adequate response for moderate-amplitude, moderate-frequency waveforms. Designers should still compare input bias current and offset voltage against the sensor impedance, and verify output swing at the selected load before committing the circuit.
おすすめ
Portable Instrumentation
The TS954IN is appropriate for portable instrumentation powered from 3V or 5V because the TS95x family is optimized for those supply rails and combines four amplifiers in one 14-DIP package. Rail-to-rail inputs help preserve measurement range near the supply limits, while the 80 dB supply-voltage rejection ratio assists in reducing supply-related errors. The four channels can support instrumentation-buffer, differential, gain, and output functions. Before using it for precision measurement, verify offset voltage, input bias current, input noise, and common-mode behavior for the specific sensor and reference circuit.
おすすめ
Active Filtering
The TS954IN can implement active low-pass, high-pass, and other feedback filters where a 3 MHz gain-bandwidth product and 1 V/us slew rate are sufficient for the signal bandwidth. Its quad-channel organization allows cascading stages or building several filters in one package, reducing board area compared with discrete single amplifiers. The 3V and 5V operating optimization also supports compact battery-powered test equipment. Component selection must account for closed-loop gain, noise gain, phase margin, component tolerances, and output loading; the complete manufacturer datasheet should be used to assess stability and output-current limits.
おすすめ
Audio Preamplification
The TS954IN can serve as a general-purpose audio preamplifier or line-stage buffer in 3V and 5V systems because it provides rail-to-rail output operation and a 3 MHz gain-bandwidth product. The 1 V/us slew rate is suitable for many low-frequency and midrange audio signals, while four channels allow convenient stereo implementation with additional monitoring or filtering channels. Headphone or loudspeaker loads require separate output-current and distortion checks, and input-noise performance must be compared with the source impedance. Decoupling and grounding should prevent supply ripple and digital switching noise from entering the audio path.
おすすめ
Data Acquisition Interfaces
The TS954IN is suitable for intermediate stages in a 12-bit or 16-bit data-acquisition interface when its input offset, bias current, noise, and output-drive behavior satisfy the converter requirements. Rail-to-rail inputs help utilize more of the available 3V or 5V sensor range, and the quad package can provide multiple amplifier functions for gain, filtering, level shifting, and reference buffering. A practical design should include anti-alias filtering, source-impedance analysis, and a converter-specific settling-time review. The manufacturer's complete electrical tables remain necessary for precision conversion because bandwidth alone does not establish total error.
おすすめ
General-Purpose Analog Buffering
The TS954IN provides four independent channels for buffering isolated sensor, interface, or control signals on a 3V or 5V board. Rail-to-rail input and output stages reduce signal-headroom loss, and the 80 dB supply-voltage rejection ratio helps isolate the buffered signal from supply noise. Use the quad organization to place several buffers near the associated circuitry and reduce trace sensitivity. Validate stability with the intended capacitive load, maintain adequate output voltage margin, and include local supply decoupling. For very high source impedances or very low-level signals, the input bias current and offset specifications should be reviewed before layout is finalized.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: TS954IN — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | TS954ID | TS954IP | TS954IYDT | OP496GP | OP496GPZ |
|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | Analog Devices | Analog Devices |
| Package | 14-DIP | 14-DIP - same | 14-DIP - same | 14-DIP - same | 14-DIP - same | 14-DIP - same |
| Amplifier Channels | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
主な差別化要因
- Four low-power amplifiers in one through-hole package （vs OP496GP)
- Specified for 3V and 5V low-voltage systems （vs OP496GPZ)
- Combination of bandwidth, slew rate, and supply rejection （vs TS954ID)
設計ノート
Design the TS954IN around its optimized 3V and 5V supply conditions and do not exceed the documented 12 V maximum supply voltage. Place a local bypass capacitor at each amplifier supply connection as indicated in the manufacturer application guidance, and keep the return path short. Because four channels share one package, aggregate supply current and thermal dissipation can rise when all channels operate simultaneously. Check each channel's output-current demand and the total package temperature rise under the worst-case load rather than evaluating only one amplifier.
Do not treat the word rail-to-rail as permission to exceed the input common-mode or output-swing limits. Confirm the signal remains inside the permitted range at the selected supply voltage and load, including the effect of output saturation. Also account for input offset voltage and bias current when the source impedance is high. Four independently configured amplifiers can introduce separate stability and saturation risks, so evaluate each channel at its actual gain and capacitive load.
Use the manufacturer pin-description table when assigning the 14-DIP footprint and maintain a common ground reference across all four channels. Route sensitive input and feedback traces away from switching nodes and high-current return paths. Keep supply-decoupling connections short, use an adequate ground plane, and place input-conditioning components close to their associated pins. Although the through-hole package tolerates longer routing than many SMD packages, minimizing loop area remains important because the 80 dB supply rejection specification is only effective within its stated test conditions.
Use the 3 MHz gain-bandwidth product to select a closed-loop gain and feedback network that retains adequate phase margin over the intended signal bandwidth. The 1 V/us slew rate limits large-signal response, so a circuit that meets small-signal bandwidth requirements can still distort faster full-scale transitions. For filters or oscillators, include component tolerances and amplifier noise gain in the design. Check capacitive loading and add an isolation resistor when driving long PCB traces or cable capacitance.
コンプライアンス情報
The verified manufacturer-family information identifies a general-purpose operational amplifier and does not state product-specific RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification status.