XMC1100T016F0016ABXUMA1 - 32MHz ARM Cortex-M0 MCU | Infineon
部品番号: XMC1100T016F0016ABXUMA1 ✓ 生産中XMC1100T016F0016ABXUMA1 概要
A microcontroller is a programmable system-on-chip that integrates a processor core, memory, clock circuitry, and peripherals such as timers, communication interfaces, and analog-to-digital converters. The ARM Cortex-M0 core provides a deterministic instruction set suitable for event-driven control. Within the device hierarchy, this MCU belongs to the XMC1000 family, combines ARM Cortex-M0 processing with embedded analog and timer resources, and targets industrial real-time control designs.
Principal features include a 32 MHz operating frequency, 16 KB of Flash memory organized as 16K by 8, and a 32-bit processor architecture. The 16-pin TSSOP-16 package supports compact PCB layouts while retaining port multiplexing capabilities. The XMC1100 platform is designed for demanding yet cost-sensitive applications, and its analog acquisition and timer resources can support control loops, signal acquisition, and peripheral communication in the same device.
The XMC1100 device family uses configurable port multiplexing so individual pins can carry several alternate functions, including up to seven alternate output functions mapped to a port pin. This flexibility helps designers optimize pin assignment on a small 16-pin package. Clocking and timer resources organize real-time tasks, while the microcontroller's control-oriented peripherals reduce the need for separate discrete components.
Typical uses include industrial sensor controllers, compact motor and actuator control nodes, LIN-connected automotive subsystems, small power-conversion controllers, and embedded measurement modules. The device is particularly suitable when a 32 MHz control loop, fast peripheral access, and 16 KB of code storage are sufficient for the application. Firmware development is supported by the ARM Cortex-M0 ecosystem and Infineon XMC tooling.
Designers should allocate decoupling capacitors, route sensitive analog inputs away from fast switching nodes, and confirm the selected port's alternate-function mapping in the manufacturer datasheet. Before production release, review the errata sheets for the AB step and verify low-power wake-up, timer, and serial-interface behavior against the final board layout and firmware configuration.
This page consolidates the Infineon ordering information, datasheet characteristics, distributor availability references, drop-in options, and practical integration guidance into one engineering-focused resource. It also distinguishes confirmed pin-compatible alternatives from parts that merely share similar specifications.
ドロップイン代替品: XMC1100T016F0016ABXUMA1 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: XMC1100T016F0016ABXUMA1 (同一形状・フットプリント) — 相違点: Product Type, Series.
XMC1100T016F0016AAXUMA1
✅ ドロップイン📋 参考代替品(カタログ未掲載)
XMC1100T016X0032AAXUMA1
✅ ドロップイン📋 参考代替品(カタログ未掲載)
XMC1100T016X0016AAXUMA1
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →XMC1100T016F0016ABXUMA1 最大定格&電気的特性
| Product Type | 32-bit ARM Cortex-M0 microcontroller |
| Series | XMC1000 |
| Processor Core | ARM Cortex-M0 |
| CPU Architecture | 32-bit |
| Maximum CPU Frequency | 32 MHz |
| Program Memory Type | Flash |
| Program Memory Size | 16 KB |
| Program Memory Organization | 16K x 8 |
| Package Type | PG-TSSOP-16 |
| ピン数 | 16 pins |
| 実装タイプ | Surface mount |
| Product Segment | Industrial |
| Application Focus | Price-sensitive real-time control |
| Port Multiplexing | Up to 7 alternate output functions per port pin |
| Ordering Code | XMC1100-T016F0016-AB |
| Silicon Step | AB step |
XMC1100T016F0016ABXUMA1 pg-tssop-16 ピン配置ガイド
XMC1100T016F0016ABXUMA1 (pg-tssop-16 パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: XMC1100T016F0016ABXUMA1.
詳細は データシート をご参照ください。
主な用途
XMC1100T016F0016ABXUMA1 の用途: 6 件s: Industrial Sensor and Condition Monitoring, Compact Motor and Actuator Control, LIN-Connected Automotive Subcontroller, Small Power-Conversion Controller, Embedded Measurement and Signal Acquisition, HMI Button and Encoder Interface Module.
Industrial Sensor and Condition Monitoring
The Infineon XMC1100T016F0016ABXUMA1 fits compact monitoring nodes that sample analog inputs and apply filtering or control logic at 32 MHz. Its 16 KB of Flash provides room for a bootloader, acquisition routines, filtering, and communication services without requiring a larger package. The 16-pin PG-TSSOP-16 footprint also simplifies dense instrument panels. Use the port alternate-function table when assigning communication and timer signals, and isolate analog inputs from switching nodes to preserve measurement quality.
おすすめ
Compact Motor and Actuator Control
A 32 MHz ARM Cortex-M0 core gives the XMC1100T016F0016ABXUMA1 enough timing headroom for responsive motor, valve, or actuator control loops in a small embedded controller. Its timer and port resources support PWM-capable output assignments, while 16 KB of Flash can hold compact control loops and safety checks. The TSSOP-16 package minimizes board area in distributed actuator nodes. Confirm pin multiplexing and peripheral allocation in the manufacturer datasheet before assigning motor-control outputs.
おすすめ
LIN-Connected Automotive Subcontroller
The XMC1100T016F0016ABXUMA1 is appropriate for small automotive subcontrollers that require deterministic timing, compact packaging, and a cost-conscious control core. At 32 MHz, the Cortex-M0 processor can service control logic alongside communication tasks, and the 16-pin package supports space-constrained harness electronics. Review the AB-step errata for LIN UART timing and low-power wake-up behavior, then validate the complete network interface against the vehicle system requirements.
おすすめ
Small Power-Conversion Controller
The 32 MHz processing rate of the XMC1100T016F0016ABXUMA1 supports digital control loops, fault handling, and power sequencing in a compact auxiliary supply controller. Its 16 KB of Flash accommodates a control state machine and communication handlers, while configurable alternate functions help optimize a limited pin count. Place the device away from switching nodes, follow the recommended decoupling arrangement, and verify switching-node timing margins because the MCU must remain responsive while power stages operate.
おすすめ
Embedded Measurement and Signal Acquisition
The XMC1100T016F0016ABXUMA1 can act as the control and processing element in a small measurement module that combines analog acquisition with timer-based sampling. Its Cortex-M0 architecture supports deterministic execution, and the compact TSSOP-16 package leaves board space for sensing and interface circuitry. Use shielded or carefully routed analog traces, add local supply bypassing, and confirm the ADC and sampling specifications directly in the Infineon manufacturer datasheet before setting acquisition timing.
おすすめ
HMI Button and Encoder Interface Module
A compact XMC1100T016F0016ABXUMA1-based module can debounce controls, decode incremental encoders, drive indicators, and communicate status to a host controller. The 32 MHz core provides quick response with a relatively simple 16 KB firmware footprint, and the 16-pin package suits densely populated panels. Configure port inputs, alternate output functions, and timer resources from the datasheet pin table. Debounce and timing decisions should be validated in real hardware because mechanical contact behavior is not represented by the MCU datasheet.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: XMC1100T016F0016ABXUMA1 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | XMC1100T016F0016AAXUMA1 | XMC1100T016X0032AAXUMA1 | XMC1100T016X0016AAXUMA1 |
|---|---|---|---|---|
| Brand | Infineon | Infineon | Infineon | Infineon |
| Package | PG-TSSOP-16 | PG-TSSOP-16 - same | PG-TSSOP-16 - same | PG-TSSOP-16 - same |
| Processor Core | ARM Cortex-M0 | ARM Cortex-M0 | ARM Cortex-M0 | ARM Cortex-M0 |
| CPU Architecture | 32-bit | 32-bit | 32-bit | 32-bit |
| Maximum CPU Frequency | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Silicon Step | AB step | AA step | AA step | AA step |
| Pin Count | 16 pins | 16 pins | 16 pins | 16 pins |
| Product Segment | Industrial | Industrial | Industrial | Industrial |
| Primary Application | Price-sensitive real-time control | Price-sensitive real-time control | Real-time control | Real-time control |
主な差別化要因
- Specific AB-step sourcing position (vs XMC1100T016F0016AAXUMA1)
- 32 MHz execution rate with compact 16 KB Flash configuration (vs XMC1100T016X0032AAXUMA1)
- Industrial positioning in a space-efficient PG-TSSOP-16 package (vs XMC1100T016X0016AAXUMA1)
設計ノート
Place the supply decoupling network directly beside the VDD and VSS connections, with a short ground return path to reduce loop area. The listing excerpt does not reproduce the capacitor values or operating-voltage limits, so use the decoupling and voltage recommendations in the Infineon AB-step manufacturer datasheet. Check the supply ramp against the device's reset and power-on requirements, and confirm the AB-step errata before enabling production firmware.
Assign port functions before laying out the PCB because the PG-TSSOP-16 footprint provides limited routing options and several pins support alternate peripheral outputs. Use the manufacturer pin-description and alternate-function tables to select the best signal mapping, then reserve the remaining pins for serial communication, control, and status. Keep analog-capable inputs away from switching outputs and route high-speed or externally modulated signals over controlled return paths.
Do not assume that a matching TSSOP-16 outline guarantees identical behavior. The AA and AB silicon steps can have different errata affecting LIN UART timing, low-power wake-up, timers, or other peripherals. Before substituting an order code, compare the complete ordering table, memory configuration, pin multiplexing, electrical characteristics, and applicable errata sheets. Program a device-level functional test that exercises the communications interface, wake-up path, timers, and analog functions used by the product.
Treat external sensor, communication, and actuator interfaces as separate signal domains even when they share the microcontroller supply. Keep return currents within their intended ground regions, avoid routing sensitive inputs beneath switching nodes, and use the package and board guidance in the Infineon documentation. If the board includes a switching power stage, verify the control MCU's timing behavior during startup, overload, and recovery rather than relying only on steady-state operation.
コンプライアンス情報
The Infineon ordering information identifies the device as an industrial XMC1000 microcontroller, but the extracted source excerpts do not state RoHS, REACH, halogen-free, or conflict-minerals status. Confirm these declarations on the current manufacturer product page or material declaration before procurement.