집적 회로

하위 카테고리

📁 ADC/DAC 2518 제품 📁 증폭기 IC 793 제품 📁 오디오 코덱 16 제품 📁 오디오 IC 2 제품 📁 클록 및 타이밍 287 제품 📁 DSP 962 제품 📁 데이터 수집 IC 2 제품 📁 디지털 포텐셔미터 4 제품 📁 디스플레이 드라이버 및 컨트롤러 1 제품 📁 FPGA & CPLD 6666 제품 📁 인터페이스 IC 1568 제품 📁 LED 드라이버 1 제품 📁 로직 IC 305 제품 📁 메모리 IC 875 제품 📁 마이크로컨트롤러 18688 제품 📁 마이크로프로세서 4 제품 📁 모터 드라이버 1 제품 📁 기타 1 제품 📁 Sensor and Detector Interfaces 1 제품 📁 특수 IC 15 제품 📁 비디오 IC 13 제품

제품 (32725)

USB2502-HT - 2-Port USB 2.0 Hub Controller | Microchip
USB2502-HT

USB2502-HT - 2-Port USB 2.0 Hub Controller | Microchip

The Microchip Technology USB2502-HT is a two-port USB 2.0 hub controller supporting low-speed, full-speed, and high-speed USB devices in a 48-pin TQFP package. According to Microchip's USB2502 data sheet, its two downstream-facing ports can operate at 1.5 Mb/s, 12 Mb/s, or 480 Mb/s when connected to a high-speed host. The controller is designed for systems that need to expand one USB host connection into two downstream USB ports while maintaining USB 2.0 specification compliance. A USB hub controller is an interface integrated circuit that manages traffic between an upstream host and multiple downstream ports. In the USB hierarchy, it belongs to the USB interface-controller class, the broader interface-IC category, and ultimately the semiconductor device hierarchy. The USB2502 is intended for computers, peripherals, embedded systems, industrial equipment, and other USB 2.0 host platforms that require downstream-port expansion. Key verified features include two downstream-facing USB ports, USB 2.0 specification compliance, operation with a high-speed host, and support for low-, full-, and high-speed devices. The Microchip data-sheet result identifies the device as a fully specification-compliant USB 2.0 2-port hub and states compliance with Universal Serial Bus Specification Revision 2.0 dated April 27, 2000, including the listed 12/7/2000 and 5/28/2002 errata. The verified distributor listing identifies the physical part as a 48-TQFP USB interface IC. The controller separates upstream host traffic from the two downstream links, allowing peripheral devices such as keyboards, storage devices, network adapters, and human-interface devices to share one USB host port. System designers must provide the required USB transceiver, clock, decoupling, connectivity, and external passives described by the manufacturer data sheet. The controller itself is not a power-management IC and has no SOA data in the supplied sources. Typical uses include two-port desktop hubs, embedded USB expansion, peripheral connection panels, test equipment, and industrial USB interfaces. For a new design, validate the host controller, connector overmolding, cable lengths, enumeration behavior, power budgeting, and all USB electrical and timing requirements. The supplied evidence identifies the USB2502 family, but does not provide a complete pin-by-pin pinout or every operating limit, so those details remain to be verified from the manufacturer documentation. This product page consolidates the verified manufacturer description, distributor package information, source links, and engineering-use guidance for USB2502-HT selection. It intentionally distinguishes verified facts from missing electrical details instead of estimating unspecified values.

견적 요청 재고 있음
USB2503-HZE - USB 2.0 3-Port Hub Controller | Microchip
USB2503-HZE

USB2503-HZE - USB 2.0 3-Port Hub Controller | Microchip

The Microchip USB2503-HZE is a USB 2.0 three-port hub controller packaged in a 48-QFN (7x7 mm) package. According to the verified manufacturer material, it is fully compliant with the USB 2.0 Specification, does not require firmware development, and supports low-speed, full-speed, and high-speed downstream devices when attached to a compatible host. Its principal role is to add three downstream USB ports while presenting one upstream connection to the host system. A USB hub controller is an interface integrated circuit that manages traffic between one upstream USB connection and multiple downstream ports. It belongs to the USB interface-controller family and the broader semiconductor and connectivity hierarchy. By handling USB enumeration, port attach and detach events, and downstream power-management coordination, the controller reduces the amount of host software and external glue logic required in a USB hub design. The verified product information identifies the USB2503 as a three-port hub controller compliant with USB 2.0. The manufacturer description states that the controller does not require firmware development, simplifying implementation compared with solutions that need device-specific firmware or a substantial software stack. Downstream ports can operate at 1.5 Mb/s low speed and at the other USB speed modes supported by the USB 2.0 specification when connected to an appropriate high-speed host. The HZE suffix identifies the ordered package variant associated with the supplied datasheet and distributor records. The device is offered in a 48-QFN (7x7 mm) surface-mount package, making it suitable for compact USB hub equipment where the connector footprint and board area are constrained. The package requires careful placement of power, USB data, configuration, clock, and exposed-pad connections according to the manufacturer pinout and layout guidance. Typical applications include USB hubs, docking stations, desktop and laptop peripherals, embedded USB expansion systems, industrial equipment, test and measurement products, and host systems requiring additional USB connectivity. The controller can also support designs that need automatic connection to a USB host without developing a dedicated USB hub firmware image. For implementation, confirm the exact USB operating modes, electrical limits, regulator requirements, crystal or clock configuration, port-power requirements, and exposed-pad layout against the USB2503/USB2503A manufacturer datasheet. When comparing a replacement, verify that the candidate uses the same 48-QFN footprint, pin functions, voltage requirements, USB electrical behavior, and intended upstream/downstream configuration rather than relying only on the apparent USB 2.0 hub function. This page consolidates the verified USB2503-HZE product description, distributor references, datasheet links, package information, pricing references, and engineering selection guidance. It is intended to help designers identify whether the controller fits a USB hub design and to locate the manufacturer documentation needed for a final, board-specific engineering review.

견적 요청 재고 있음
USB2503-HZH - 3-Port USB 2.0 Hub Controller | Microchip
USB2503-HZH

USB2503-HZH - 3-Port USB 2.0 Hub Controller | Microchip

The Microchip USB2503-HZH is an integrated USB 2.0 compliant 3-port hub controller housed in a 48-pin QFN-EP (7x7 mm) package with an exposed thermal pad. The device is fully compliant with the USB 2.0 specification and requires no firmware development, simplifying integration into embedded systems, docking stations, monitors, and multi-port consumer electronics. When attached to a USB high-speed host, the three downstream ports each support low-speed (1.5 Mb/s), full-speed (12 Mb/s), and high-speed (480 Mb/s) operation through dedicated transaction translators. A USB hub controller is a line/bus controller that expands a single upstream USB port into multiple downstream ports while handling protocol translation, power management, and device enumeration. The USB2503 belongs to the hub controller family, which sits within the broader USB interface IC category and the overall peripheral controller hierarchy. The device integrates a Transaction Translator (TT) per port using Microchip's MultiTRAK technology, which improves concurrent bandwidth by allowing multiple full-/low-speed devices to operate simultaneously without bandwidth contention. Key features include pin-selectable default configuration, optional EEPROM or SMBus microcontroller configuration, integrated 1.8 V core LDO, support for both bus-powered and self-powered modes, dynamic port-power switching, and per-port overcurrent detection. The 48-QFN-EP package provides an exposed thermal pad for enhanced heat dissipation and a 0.5 mm pitch for compact PCB layout. The device operates from 3.0 V to 3.6 V and supports a 0 °C to 70 °C commercial temperature range. Architecturally, the USB2503 combines a USB 2.0 physical layer, serial interface engine, hub repeater, three transaction translators, and port-control logic on a single die. The integrated USB transceivers support both high-speed (480 Mb/s) and full-speed (12 Mb/s) signaling, with internal pull-up/pull-down resistors defined by the USB specification. Configuration via an external I2C EEPROM or an SMBus-capable microcontroller enables vendor ID, product ID, port-remap, and non-removable-port settings without firmware changes to the host. Typical applications include USB port expansion in desktop PCs, docking stations, monitors with built-in USB hubs, industrial PCs, point-of-sale terminals, embedded computing platforms, and USB-equipped printers. Designers select this part when a 3-port USB 2.0 hub is needed with no firmware investment and minimal BOM cost. When designing with this part, ensure downstream-port power filtering complies with USB 2.0 inrush and voltage-drop budgets, and connect 10 kΩ pull-ups on SDA/SCL per the SMBus 1.0 specification. The exposed pad must be soldered to the ground plane to meet thermal and EMI performance. This page synthesizes distributor pricing, pin-compatible drop-in alternatives such as the USB2513B-AEZC family, and practical layout notes not consolidated in the manufacturer datasheet.

USD $3.10 재고 있음
USB2504-JT USB 2.0 4-Port Hub Controller | Microchip
USB2504-JT

USB2504-JT USB 2.0 4-Port Hub Controller | Microchip

The Microchip Technology USB2504-JT is a USB 2.0 four-port hub controller with no firmware development required, supporting low-speed 1.5 Mb/s, full-speed 12 Mb/s, and high-speed 480 Mb/s downstream operation in a 64-pin TQFP package measuring 10 x 10 mm. The controller integrates the hub interface logic needed to manage four USB downstream ports while attaching to a USB host. An integrated USB hub controller is a semiconductor interface device that expands one host USB connection into multiple downstream ports. It sits between a USB host and peripherals, handling port attach, disconnect, enumeration, power-gating, and traffic routing. The USB2504 family is positioned within the USB interface-controller and peripheral-controller hierarchy, providing infrastructure for USB hubs without requiring a separate hub firmware. Key features include compliance with the USB 2.0 specification, four downstream ports, firmware-free configuration, low-speed, full-speed, and high-speed downstream support, and operation from a 3 V to 3.6 V supply according to the USB2504A-JT comparison data. Configuration can use strapping options, an external EEPROM, or a microcontroller interface; when connected to a microcontroller, the hub appears as an SMBus slave device. The controller is designed for USB hubs, docking stations, KVM equipment, and embedded systems that need more than one USB port. Its 64-pin TQFP package provides the required external connectivity for four downstream channels and upstream USB signaling. USB 2.0 hub designs must still provide correct power distribution, downstream-port protection, layout routing, and connector implementation; the controller itself does not eliminate those board-level requirements. A key design consideration is power budgeting. Each enabled downstream port can require current for attached USB devices, so the power supply, switches, protection components, and connector wiring must be sized for the worst-case load. High-speed USB traces also require controlled impedance, short return paths, and careful separation from noisy power and switching circuitry. Microchip documentation provides configuration guidance for EEPROM and microcontroller-based implementations. This page synthesizes verified manufacturer and distributor information, cross-reference results, package details, and practical engineering considerations. It distinguishes documented USB2504 features from parameters that require confirmation in the manufacturer datasheet, helping engineers evaluate the USB2504-JT for four-port USB hub designs.

USD $3.95 재고 있음
USB2504A-JT - USB 2.0 4-Port Hub Controller | Microchip
USB2504A-JT

USB2504A-JT - USB 2.0 4-Port Hub Controller | Microchip

The Microchip Technology USB2504A-JT is a USB 2.0 four-port hub controller supporting high-speed 480 Mbit/s, full-speed 12 Mbit/s, and low-speed 1.5 Mbit/s devices. It is supplied in a 64-pin TQFP package measuring 10 mm by 10 mm and operates from a 3 V to 3.6 V supply. A USB hub controller is an interface IC that expands one upstream USB connection into multiple downstream ports while managing transaction translation, enumeration, power, and device connectivity. The USB2504A belongs to the USB interface-controller hierarchy, integrating USB 2.0 connectivity and four-port hub management into a single semiconductor device. The controller provides four transaction translators, one per downstream port, for independently handling supported USB traffic speeds. It supports per-port or ganged, selectable downstream power control and can detect whether the hub source is bus-powered or self-powered. According to the Microchip product page, the device is fully USB 2.0 compliant and requires no firmware development. Configuration can begin with pin-selectable defaults, limited strapping options, an external EEPROM, or a microcontroller interface. When configured through a microcontroller, the hub appears as an SMBus slave, allowing an external controller to alter supported configuration options. Dynamic power switching monitors the SELF_PWR input and removes downstream and upstream power when local supply availability changes. Typical uses include USB 2.0 docking stations, desktop hubs, KVM equipment, external storage interfaces, embedded USB expanders, and industrial peripheral hubs. Four high-speed transaction translators make the controller appropriate when several peripherals must coexist behind one host connection without relying on USB firmware. PCB design must preserve high-speed USB routing discipline, including a short upstream path, controlled impedance, continuous reference planes, and placement of required decoupling close to the device. The exact pin names, capacitor values, clock requirements, operating temperature, and power ratings must be confirmed against the manufacturer datasheet before layout release. This page consolidates the verified manufacturer and distributor facts, distinguishes the explicitly supported USB2504-JT cross-reference from unsupported substitutions, and identifies engineering details that still require direct datasheet confirmation.

견적 요청 재고 있음
USB2507-ADD - USB 2.0 7-Port Hub | Microchip Technology
USB2507-ADD

USB2507-ADD - USB 2.0 7-Port Hub | Microchip Technology

The Rochester Electronics USB2507-ADD is an integrated USB 2.0-compatible seven-port hub controller based on the SMSC USB2507, packaged in an 80-pin TQFP measuring 12 x 12 mm. It supports seven downstream USB connections at low speed, 1.5 Mb/s, full speed, 12 Mb/s, and—when attached to a high-speed host—high speed, 480 Mb/s. Configuration does not require custom firmware, making the device suitable for embedded USB expansion, legacy PC systems, printers, storage peripherals, and industrial equipment. A USB hub controller is an interface IC that bridges one upstream USB host connection to multiple downstream ports while transaction translators isolate traffic on each active link. Within the USB interface hierarchy, the USB2507 family belongs to the seven-port hub-controller class and implements USB 2.0 connectivity. Per-port or ganged downstream power control can be selected, while bus-powered and self-powered source conditions can be detected. Configuration can use strapping options, an external EEPROM, or a microcontroller interface; with the latter, the hub operates as an SMBus slave. Key verified capabilities include seven transaction translators, operation at 1.5 Mb/s, 12 Mb/s, and 480 Mb/s, full power management, selectable per-port or ganged power control, and bus-power or self-power detection. The controller also supports an on-board 24 MHz crystal driver or a 24 MHz external clock, an internal PLL for 480 MHz USB 2.0 sampling, and an integrated 1.8 V linear voltage regulator. These blocks reduce the external clock, timing, and supporting circuitry normally required by a multiport USB hub. The -ADD order code is offered in the same 80-TQFP, 12 x 12 mm package identified for USB2507-ADT by the verified distributor data. Because both parts use the same base USB2507 family, that package relationship supports direct footprint reuse, although functional equivalence should still be confirmed against the manufacturer pin table and ordering information. The manufacturer documentation also identifies SMBus and serial configuration paths, supporting designs that require adjustable runtime or manufacturing configuration. Typical installations include legacy industrial computers, medical carts, test systems, peripheral concentrators, USB-to-serial equipment, and embedded platforms needing more than the host controller's native ports. In a typical design, one upstream USB line connects to the host, while seven downstream routes connect to internal or external connectors. The principal engineering constraints are USB differential routing, correct power budgeting, connector protection, support for bus- or self-powered operation, and compliance with the electrical requirements stated in the manufacturer datasheet. When laying out the board, treat the differential USB pairs as controlled-impedance nets and keep upstream and downstream routing separated to minimize crosstalk. Provide the crystal or supported 24 MHz clock network exactly as specified, place decoupling close to the supply pins, and confirm that downstream power switches can meet the required inrush and over-current behavior. The USB2507-ADD can simplify firmware development, but it does not remove the need for correct host support, power architecture, connector design, and USB signal integrity.

견적 요청 재고 있음
USB2507-ADT USB 2.0 7-Port Hub Controller | Microchip
USB2507-ADT

USB2507-ADT USB 2.0 7-Port Hub Controller | Microchip

The Microchip Technology USB2507-ADT is an integrated USB 2.0-compatible seven-port hub controller with high-speed 480 Mbit/s, full-speed 12 Mbit/s, and low-speed 1.5 Mbit/s operation, housed in an 80-pin TQFP package measuring 12 x 12 mm. It provides one upstream host-facing connection and seven downstream USB ports, making it a practical interface controller for powered hubs, docking systems, industrial equipment, and multiport USB expansion. A USB hub controller is a semiconductor that manages traffic between one upstream USB host and multiple downstream peripherals. It belongs to the USB interface-controller hierarchy, which combines USB transaction translation, port management, clock recovery, power supervision, and device connectivity. The USB2507 is designed as a dedicated USB 2.0 hub rather than a general-purpose microcontroller, reducing the need for custom firmware and allowing compatible USB devices to share a host port. Verified product information identifies seven downstream ports, USB 2.0 compatibility, and support for low-speed, full-speed, and high-speed devices. Search results also describe an internal 24 MHz crystal-driver circuit or external 24 MHz clock source, an internal phase-locked loop for 480 Mbit/s sampling, an internal 1.8 V linear regulator, integrated USB terminations and bias resistors, and short-circuit protection on USB differential pins. These functions support a compact hub implementation while reducing external clock and signal-conditioning overhead. Configuration flexibility is provided through strapping options, an external EEPROM, or a microcontroller interface. Search data indicates that a microcontroller-connected hub appears as an SMBus slave, while strap options modify a limited subset of configuration choices. This allows prototype settings to change without firmware and production designs to use persistent configuration when required. Typical uses include USB docking stations, external storage connectivity, laboratory equipment, computer-accessory consolidation, and embedded systems that need seven downstream USB connections. The controller should be paired with suitable hub-board power switching, protection, connectors, and layout that preserves USB differential-signal integrity. Designers must also verify the current electrical limits, pin functions, clock source, and reference configuration directly against the manufacturer datasheet before layout release. The principal design consideration is that USB hub design combines high-speed edge-rate signaling with exposed connector paths. Controlled impedance, short matched traces, careful return paths, correct terminations, and verified power-supply sequencing are essential. The 80-pin TQFP footprint is not interchangeable with a smaller controller without a PCB redesign, even when another hub offers the same USB version. This product record combines the verified Microchip USB2507 data, official datasheet links, distributor package information, configuration details, and practical implementation guidance. It is intended to support engineering selection and sourcing, while flagging missing electrical, lifecycle, pricing-tier, pinout, and compliance values rather than inventing them.

견적 요청 재고 있음
USB2512B-I/M2 - 2-Port USB 2.0 Hi-Speed Hub Controller | Microchip
USB2512B-I/M2

USB2512B-I/M2 - 2-Port USB 2.0 Hi-Speed Hub Controller | Microchip

The Microchip USB2512B-I/M2 is a 2-port USB 2.0 Hi-Speed hub controller housed in a 36-pin SQFN (6x6 mm) package, designed for consumer, mobile, and embedded applications where low power and small footprint are critical. It operates across a 3.0 V to 3.6 V supply range, supports USB 2.0 Hi-Speed (480 Mbps), Full-Speed (12 Mbps), and Low-Speed (1.5 Mbps) downstream signaling, and integrates Microchip's MultiTRAK™ (multi-transaction translator) technology with one transaction translator per downstream port for parallel traffic handling. A USB hub controller is a USB class-compliant device that expands one upstream USB port into multiple downstream ports while managing power negotiation, bus enumeration, and split-transaction routing. The hub sits in the broader USB controller hierarchy (USB 2.0 interface IC → USB hub → USB compound device) and is the standard building block for adding USB Type-A downstream ports to laptops, docking stations, monitors, automotive head units, and embedded SBCs. Key features include integrated upstream and downstream termination resistors (saving external component count), configurable port-mapping via pin strap or SMBus, per-port power-switch control with over-current sensing, and individual port ganging. The device supports battery-charging detection (BC 1.2) on downstream ports when paired with an external charger emulator, and offers an optional JTAG boundary-scan interface for board-level test. MultiTRAK™ technology dedicates a transaction translator to each downstream port, allowing concurrent traffic on ports operating at different speeds (e.g., a Full-Speed keyboard plus a Hi-Speed storage drive). Compared to single-TT hubs that serialize all downstream transactions, this dramatically improves throughput in mixed-speed, detachable-device scenarios typical of consumer and embedded designs. Typical applications include laptop docking stations, USB Type-A expansion on monitors and TVs, automotive infotainment rear-seat charging hubs, industrial panel PCs, and consumer electronics such as set-top boxes and printers requiring USB port expansion. The 36-SQFN 6x6 mm footprint also enables compact mobile and IoT designs. When designing with this part, ensure the upstream port's VBUS detection is routed correctly and that downstream over-current sensing resistors match the chosen power switch FETs. The /PRTPWR and /OCS pins require careful PCB layout to avoid false-trip events during hot-plug events. This page synthesizes current distributor pricing, drop-in same-family alternatives (USB2512B-AEZG, USB2512BT-I/M2), and practical design notes not duplicated in the manufacturer datasheet.

USD $2.49 재고 있음
USB2512B/M2 - 2-Port USB 2.0 Hub Controller | Microchip
USB2512B/M2

USB2512B/M2 - 2-Port USB 2.0 Hub Controller | Microchip

The Microchip Technology USB2512B/M2 is a low-power, OEM-configurable 2-port USB 2.0 Hi-Speed hub controller packaged in a 36-SQFN (6x6 mm) package. It supports one upstream USB connection and two downstream ports, making it suitable for embedded USB expansion in consumer, mobile, and portable systems. The supplied source data identifies it as a full-featured USB hub controller using the USB2512B MultiTRAK architecture. A USB hub controller is an interface IC that sits between a USB host and one or more USB peripherals. The USB2512B/M2 manages USB traffic, provides downstream-port connectivity, and supports USB 2.0-compatible device integration. Its two-port structure is useful where a host interface needs to connect multiple peripherals without redesigning the host system. The controller is positioned for USB 2.0 Hi-Speed hub designs and is described by Microchip as low-power and cost-effective. The USB2512B family provides configurable behavior for OEM embedded products. The USB2512B/M2 ordering code is associated with the 36-SQFN package, and distributor results identify the part as a 2-port USB 2.0 Hi-Speed hub controller. Typical applications include USB hubs in mobile accessories, consumer electronics, docking systems, portable equipment, and embedded USB peripherals. The two downstream ports can simplify connection of peripherals such as keyboards, storage devices, input controllers, or other USB-compatible accessories when the system power and enclosure allow it. The key design consideration is that USB hub implementation involves more than placing the controller on a PCB. Power-supply design, downstream-port overcurrent protection, USB signal routing, connector selection, firmware configuration, and compliance testing must be developed together. Review the manufacturer datasheet and evaluation-board documentation before finalizing a production layout. This page summarizes the verified manufacturer and distributor information, identifies the known application context, and separates confirmed data from specifications that still require confirmation in the datasheet or design documentation.

USD $2.16 재고 있음
USB2512BI-AEZG - 2-Port USB 2.0 Hi-Speed Hub Controller | Microchip
USB2512BI-AEZG

USB2512BI-AEZG - 2-Port USB 2.0 Hi-Speed Hub Controller | Microchip

The Microchip Technology USB2512BI-AEZG is a 2-port USB 2.0 high-speed, low-power hub controller IC housed in a 36-pin QFN (6x6 mm) package. The device operates from a single 3.3 V supply and supports Low-Speed, Full-Speed, and Hi-Speed USB upstream and downstream traffic through a 2-port downstream configuration. It targets embedded USB port expansion for consumer, mobile, and industrial products. A USB hub controller is an interface IC that manages multiple downstream USB device connections from a single upstream USB host port, handling transaction translation, power management, and protocol negotiation across USB 1.1 (Low/Full Speed) and USB 2.0 (Hi-Speed) links. The USB2512BI-AEZG belongs to the USB 2.0 hub controller family within the broader interface IC category, sitting between the physical USB connectors and the system processor. Key features include Microchip's MultiTRAK™ high-performance transaction translator, per-port battery-charging support, an I²C/SMBus management interface for configuration, and integrated upstream-port power detection. The industrial temperature grade (-40°C to +85°C) plus 3.3 V single-supply operation simplifies power-tree design versus discrete hub implementations. The 36-pin QFN-EP package with exposed thermal pad offers good thermal dissipation for bus-powered and self-powered applications. Internally, the device uses a USB 2.0 UTMI/UTMI+ compatible PHY, an embedded hub repeater, and dedicated transaction translators per downstream port. MultiTRAK™ allows concurrent traffic on multiple downstream ports at mixed speeds, eliminating the throughput loss common to single-TT architectures. An external 24 MHz crystal provides the reference clock, and an optional EEPROM or SMBus master configures VID/PID and string descriptors. Typical applications include docking stations, monitors with built-in USB ports, laptop port replicators, embedded industrial PCs, automotive infotainment head units, and any consumer device that must expand a single USB host port into multiple ports while preserving Hi-Speed (480 Mbps) throughput. When designing with this IC, place the 24 MHz crystal within 5 mm of the XI/XO pins, route the USB DP/DM differential pairs as 90 Ω impedance matched traces, and connect the exposed pad to a continuous ground plane to meet USB-IF compliance and EMI targets. This page synthesizes verified distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

USD $2.45 재고 있음
USB2513B-AEZC - 3-Port USB 2.0 Hi-Speed Hub Controller | Microchip (Tape & Reel)
USB2513B-AEZC

USB2513B-AEZC - 3-Port USB 2.0 Hi-Speed Hub Controller | Microchip (Tape & Reel)

The Microchip USB2513B-AEZC is a 3-port USB 2.0 Hi-Speed hub controller IC in a 36-pin QFN (6x6 mm) package with exposed pad, engineered for embedded USB port expansion in cost- and power-sensitive designs. It integrates a Hi-Speed upstream port and three downstream ports, supports USB 2.0 Link Power Management, and operates from a single 3.3 V supply. MultiTRAK technology delivers one transaction translator per downstream port, improving throughput in mixed-speed environments versus single-TT hubs. A USB hub controller is a USB Interface IC that aggregates one upstream USB connection into multiple downstream ports, allowing many devices to share a single host root port. Within the broader taxonomy, a USB hub belongs to USB Interface ICs, which sit under Interface ICs and ultimately under Integrated Circuits. The USB2513B-AEZC implements the hub repeater and transaction-translator functions defined by the USB 2.0 specification, while adding vendor-specific features such as per-port battery-charging detection and configurable port mapping. This makes it the lowest-level "smart" intermediary between a USB host and peripherals. Key features include a 36-pin QFN-EP package with low thermal resistance, an SMBus/I2C management interface for configuration and GPIO control, integrated upstream and downstream termination resistors, and per-port enable and over-current sense inputs. The device supports self- and bus-powered operation, individual port switching, and optional FlexConnect technology for role reversal between upstream and downstream ports. Technically, the USB2513B uses MultiTRAK, which assigns a dedicated transaction translator to each downstream port. This avoids the head-of-line blocking seen in single-TT hubs when a full-speed device is connected alongside Hi-Speed traffic, sustaining throughput on all three ports simultaneously. Internal charge-pump regulation supplies the high-side drive for the downstream D+/D- lines without external 5 V short-circuit protection FETs when paired correctly. Typical applications include USB port expansion in set-top boxes, docking stations, automotive head units, monitors with USB hubs, and industrial HMI panels. Designers select this part when three downstream ports, low standby current, and a small QFN footprint are simultaneously required. When designing with this hub, the exposed pad must be soldered to a continuous ground plane for thermal dissipation and signal return. Place the 3.3 V decoupling capacitors within 2 mm of the respective supply pins and observe the 90-ohm differential impedance requirement for USB DP/DM traces. This page synthesizes distributor pricing, drop-in alternative MPNs, and practical design notes not found in the manufacturer datasheet alone, helping procurement and embedded design teams shorten the bill-of-material selection cycle.

USD $2.78 재고 있음
USB2513B-AEZC-TR - 3-Port USB 2.0 Hi-Speed Hub Controller | Microchip
USB2513B-AEZC-TR

USB2513B-AEZC-TR - 3-Port USB 2.0 Hi-Speed Hub Controller | Microchip

The Microchip USB2513B-AEZC-TR is a 3-port USB 2.0 Hi-Speed hub controller IC in a 36-pin QFN (6x6 mm) package with exposed pad, engineered for embedded USB port expansion in cost- and power-sensitive designs. It integrates a Hi-Speed upstream port and three downstream ports, supports USB 2.0 Link Power Management, and operates from a single 3.3 V supply. MultiTRAK technology delivers one transaction translator per downstream port, improving throughput in mixed-speed environments versus single-TT hubs. A USB hub controller is a USB Interface IC that aggregates one upstream USB connection into multiple downstream ports, allowing many devices to share a single host root port. Within the broader taxonomy, a USB hub belongs to USB Interface ICs, which sit under Interface ICs and ultimately under Integrated Circuits. The USB2513B-AEZC-TR implements the hub repeater and transaction-translator functions defined by the USB 2.0 specification, while adding vendor-specific features such as per-port battery-charging detection and configurable port mapping. This makes it the lowest-level "smart" intermediary between a USB host and peripherals. Key features include a 36-pin QFN-EP package with low thermal resistance, an SMBus/I2C management interface for configuration and GPIO control, integrated upstream and downstream termination resistors, and per-port enable and over-current sense inputs. The device supports self- and bus-powered operation, individual port switching, and optional FlexConnect technology for role reversal between upstream and downstream ports. Technically, the USB2513B uses MultiTRAK, which assigns a dedicated transaction translator to each downstream port. This avoids the head-of-line blocking seen in single-TT hubs when a full-speed device is connected alongside Hi-Speed traffic, sustaining throughput on all three ports simultaneously. Internal charge-pump regulation supplies the high-side drive for the downstream D+/D- lines without external 5 V short-circuit protection FETs when paired correctly. Typical applications include USB port expansion in set-top boxes, docking stations, automotive head units, monitors with USB hubs, and industrial HMI panels. Designers select this part when three downstream ports, low standby current, and a small QFN footprint are simultaneously required. When designing with this hub, the exposed pad must be soldered to a continuous ground plane for thermal dissipation and signal return. Place the 3.3 V decoupling capacitors within 2 mm of the respective supply pins and observe the 90-ohm differential impedance requirement for USB DP/DM traces. This page synthesizes distributor pricing, drop-in alternative MPNs, and practical design notes not found in the manufacturer datasheet alone, helping procurement and embedded design teams shorten the bill-of-material selection cycle.

USD $2.78 재고 있음
USB2513B/M2 - 3-Port USB 2.0 Hi-Speed Hub Controller | Microchip
USB2513B/M2

USB2513B/M2 - 3-Port USB 2.0 Hi-Speed Hub Controller | Microchip

The Microchip Technology USB2513B/M2 is a 3-port, low-power, USB 2.0 Hi-Speed hub controller with integrated MultiTRAK™ multi-transaction translators, housed in a 36-pin SQFN (6x6 mm) package. It supports Low-Speed, Full-Speed, and Hi-Speed downstream devices on a single upstream port, and operates from a single 3.3 V supply with an internal regulator. A USB hub controller is a peripheral device that expands a single USB root port into multiple downstream ports, allowing several USB devices to share one upstream connection. USB hubs sit in the USB 2.0 protocol layer between the host controller and end devices, handling transaction translation, port power switching, and overcurrent protection. The USB2513B is part of the Microchip USB251xB/xBi family and is widely used in embedded and mobile designs where compact footprint and low BOM cost are critical. Key features of the USB2513B/M2 include support for USB 2.0 Hi-Speed (480 Mbps), full-speed (12 Mbps), and low-speed (1.5 Mbps) operation, individual or ganged downstream port power switching with overcurrent protection, Battery Charging 1.1 (BC1.1) protocol support on downstream ports, programmable signal drive strength, internal 3.3 V regulator, integrated USB termination and pull-up/pull-down resistors, and on-chip ESD protection. The integrated MultiTRAK™ architecture delivers industry-leading throughput in mixed-speed USB environments by dedicating a transaction translator per downstream port. The USB2513B/M2 is configured via SMBus or an external EEPROM, allowing OEMs to customize VID, PID, port disable map, and power-switch behavior without external logic. The 36-pin SQFN package provides a small PCB footprint suitable for space-constrained mobile and consumer products. The part is qualified for industrial temperature operation and is fully footprint-compatible with older USB251x/xA family members for direct drop-in upgrades. Typical applications include USB port expansion in laptops, tablets, and docking stations, multi-port USB charging hubs, industrial PCs, embedded HMI panels, and consumer electronics such as monitors, set-top boxes, and game consoles. BC1.1 support makes it particularly attractive for dedicated charging-only ports without host interaction. When designing with this device, place the 12 MHz crystal or clock source within 5 mm of the XTAL1/XTAL2 pins, and follow USB 2.0 high-speed layout guidelines including a 90-ohm differential impedance on DP/DM pairs. Decouple VBUS with a 4.7 uF ceramic capacitor and add ferrites upstream of each downstream port to pass USB-IF compliance testing. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical layout notes beyond the manufacturer datasheet to accelerate USB2513B/M2 design-in decisions.

USD $1.42 재고 있음
USB2514-HZH USB 2.0 Four-Port Hub Controller | Microchip
USB2514-HZH

USB2514-HZH USB 2.0 Four-Port Hub Controller | Microchip

The Microchip Technology USB2514-HZH is a USB 2.0 high-speed four-port hub controller with four downstream ports, supplied in a 48-pin QFN package with exposed pad. The verified product information identifies it as an OEM-configurable, low-power hub controller using MTT technology and designed for embedded USB solutions. Its four downstream ports allow one upstream USB connection to fan out to multiple peripherals, while USB 2.0 compliance supports high-speed and mixed-speed USB environments. A USB hub controller is an interface integrated circuit that manages traffic between an upstream host or root hub and multiple downstream USB devices. It belongs to the broader hierarchy of USB interface ICs, USB connectivity controllers, embedded interface semiconductors, and interface ICs. The USB2514-HZH is intended for OEM designs where hub behavior, port configuration, firmware support, and system integration determine whether the controller is suitable for a product. The verified data specifically describes the USB2514-HZH as a USB 2.0 high-speed four-port hub controller with four downstream ports. It is also described as low power and OEM configurable. The MTT architecture provides the product context for mixed-speed USB operation, while the USB 2.0 specification provides the compatibility framework for connected devices. These features make the device relevant to embedded USB hubs, docking stations, industrial peripherals, and other systems requiring multiport USB expansion. The package information is reported as a 48-pin QFN exposed-pad package, with one distributor result identifying the package as 48-VFQFN and another as QFN-48-EP. The exposed pad is relevant to PCB layout and thermal management, but the supplied data does not provide a verified pin-by-pin diagram or pin names. Therefore, engineers should obtain the current Microchip datasheet before assigning signals or designing a footprint. Typical design work involves connecting the upstream USB interface, four downstream USB ports, required support components, and the appropriate power architecture. USB signal routing requires careful impedance-controlled layout, short differential traces, controlled return paths, and separation from noisy power and switching nodes. Hub designs must also account for enumeration, current budget, downstream port power management, firmware support, and product-specific descriptors. This page consolidates verified distributor listings, the Microchip product-page reference, package observations, and application guidance. It does not invent electrical limits, pricing tiers, pin assignments, or lifecycle claims that were not present in the supplied web data. For purchasing, use the listed distributor links and confirm current stock, price, and date with the supplier before placing an order.

견적 요청 재고 있음
USB2514B-AEZC - 4-Port USB 2.0 Hi-Speed Hub Controller | Microchip
USB2514B-AEZC

USB2514B-AEZC - 4-Port USB 2.0 Hi-Speed Hub Controller | Microchip

The Microchip Technology USB2514B-AEZC is a 4-port USB 2.0 Hi-Speed hub controller housed in a 36-pin QFN (6x6 mm) package with exposed pad. It operates from a 3.0V to 3.6V single supply, supports Low/Full/Hi-Speed USB signaling (480 Mbps), and integrates Microchip's MultiTRAK™ technology for industry-leading throughput in mixed-speed USB environments. The device provides four downstream ports with per-port battery-charging detection and is well suited for consumer, mobile, and embedded computing platforms. What is a USB hub controller? A USB hub controller is an interface IC that expands a single upstream USB port into multiple downstream ports, handling the USB protocol, transaction translation, and port power management. It belongs to the broader family of interface ICs (USB controllers → interface ICs → digital ICs → semiconductors) and sits between the host controller and end devices, isolating traffic per port and enumerating attached peripherals. Key features include USB 2.0 Hi-Speed compliance, integrated 1.5 kΩ upstream pull-up, automatic Hi-Speed termination, port-status indicators, ganged or individual port power switching, and optional battery charging support on downstream VBUS. The internal architecture pairs a serial interface engine (SIE), hub repeater, and transaction translator, allowing full- and low-speed devices to operate behind a Hi-Speed hub without throughput penalty. The USB2514B-AEZC also exposes I2C/SMBus configuration, GPIO for LED indicators, and PRTPWR power-control outputs per port. Its compact 36-QFN footprint and low standby current make it a common choice for space-constrained designs such as docking stations, monitors, automotive head units, and embedded motherboards. Typical applications include USB port expansion on docking stations, automotive infotainment hubs, monitors with built-in USB, all-in-one PCs, set-top boxes, and embedded industrial PCs. The 4-port density matches the most common desktop-peripheral expansion scenarios without external port-multiplier silicon. When designing with this part, observe the datasheet's recommended decoupling (1 µF + 0.1 µF near VBAT and VDD33) and provide a stable 3.3V rail. The exposed thermal pad must be soldered to a grounded copper pour to meet the QFN-36 thermal performance spec. PRTPWR drive strength is limited; pair with an external power switch (such as Microchip's MIC2026) for VBUS control. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet alone.

USD $2.54 재고 있음
USB2514B/M2 - 4-Port USB 2.0 Hub Controller | Microchip
USB2514B/M2

USB2514B/M2 - 4-Port USB 2.0 Hub Controller | Microchip

The Microchip Technology USB2514B/M2 is a 4-port USB 2.0 Hi-Speed hub controller packaged in a 36-SQFN measuring 6 x 6 mm. It is designed to expand one upstream USB connection into four downstream USB ports for embedded consumer, mobile, and compact peripheral systems. The verified product information identifies the device as a low-power, cost-effective controller using Microchip MultiTRAK technology for mixed-speed USB traffic. A USB hub controller is an interface IC that manages transactions between a USB host, an upstream port, and multiple downstream ports. It belongs to the USB interface-controller hierarchy, combines interface logic and USB connectivity, and is used to add device connectivity without requiring four independent host controllers. USB 2.0 Hi-Speed denotes the 480 Mb/s operating mode, while the four-port configuration consolidates peripheral expansion into a single embedded device. The verified data specifically confirms four USB 2.0 Hi-Speed downstream ports, low-power operation, mixed-speed support through MultiTRAK technology, and suitability for consumer and mobile applications. The controller can reduce external USB switch complexity by integrating hub-management functions into one package. The 36-SQFN footprint also supports compact PCB layouts, although exposed-pad thermal management and careful high-speed routing remain essential. In a typical design, the USB2514B/M2 connects between a USB host and four downstream connectors. Each downstream branch requires appropriate USB data routing and power-path design, while the hub itself needs a suitable reference, clock, decoupling, and configuration implementation defined by the manufacturer datasheet. Because the provided data does not state operating voltage, current, clock frequency, or pin names, those values must be confirmed before schematic sign-off. The USB2514B/M2 is appropriate for docking accessories, compact embedded hubs, mobile accessories, printers, storage peripherals, and consumer equipment where four USB ports are required. Compared with the USB2513B-AEZC family member, its defining advantage is the verified four-port configuration rather than three ports; board compatibility should not be assumed solely from that functional similarity. For implementation, preserve the manufacturer-recommended USB differential impedance, minimize stubs and unnecessary vias, and keep sensitive clock and reference routing away from high-current switching nodes. Verify downstream-port current limits, power-switch selection, enumeration behavior, and thermal performance against the final enclosure and accessory load. This page consolidates verified distributor information, manufacturer product positioning, same-package comparison data, and practical integration guidance. It distinguishes confirmed USB2514B/M2 facts from parameters that require the official datasheet, helping engineers identify the correct hub controller without treating incomplete distributor summaries as complete electrical specifications.

USD $1.86 재고 있음
USB2517-JZX - 7-Port USB 2.0 Hi-Speed Hub Controller | Microchip
USB2517-JZX

USB2517-JZX - 7-Port USB 2.0 Hi-Speed Hub Controller | Microchip

The Microchip USB2517-JZX is a versatile, cost-effective, and power-efficient 7-port USB 2.0 Hi-Speed hub controller IC in a 64-pin QFN (9x9 mm) package with exposed thermal pad, designed for low-power, small-footprint embedded USB applications. It provides seven downstream USB ports, supports Low-Speed (1.5 Mbps), Full-Speed (12 Mbps), and Hi-Speed (480 Mbps) downstream devices, and operates from a 1.8V/3.3V supply rail. A MultiTRAK™ multi-transaction translator enables concurrent Full-/Low-Speed traffic on multiple downstream ports without bandwidth starvation, and the upstream port supports Hi-Speed operation in accordance with the USB 2.0 specification (April 27, 2000, with 12/7/2000 and 5/28/2002 errata). A USB hub controller is an Interface IC that aggregates multiple USB peripherals behind a single upstream port, presenting each downstream port to the host as an independent device while managing enumeration, power, and transaction translation. Within the broader system hierarchy, the USB2517-JZX sits at Interface IC → USB Controller → USB Hub Controller → USB 2.0 Hi-Speed Hub. Hub controllers are essential building blocks of docking stations, monitors, embedded industrial PCs, and consumer electronics that need to expand a single host USB root port into several usable downstream ports. Key features include per-port or ganged power switching, individual port over-current sensing, integrated 1.5 kΩ upstream pull-up resistor, OTP/serial EEPROM configuration, and support for both bus-powered and self-powered hub topologies. The 64-QFN package with EP provides low thermal resistance and a small 9x9 mm PCB footprint. The device supports SMBus or I²C configuration, complies with USB Battery Charging Specification 1.1 pre-configurations, and integrates an internal 3.3V regulator requiring only a single 3.3V supply or a 5V VBUS-derived rail. The architecture combines a USB 2.0 physical layer (PHY) and a serial interface engine (SIE) per port with a hub repeater and a MultiTRAK transaction translator. This allows multiple Full-/Low-Speed devices to communicate simultaneously with the host at full USB 2.0 bandwidth, eliminating the bandwidth bottleneck found in single-TT hub designs. The hub repeater handles connect/disconnect, suspend/resume, and reset signaling, while per-port PHYs provide signal integrity at 480 Mbps across PCB traces of typical lengths. Typical applications include USB port expansion in monitors, docking stations, industrial PCs, embedded computing, and consumer hubs. It is also used in test equipment, automotive infotainment head units, and any product that must turn one host port into seven USB 2.0 ports. The 1.8V/3.3V flexible supply and small 9x9 mm QFN make it ideal for space-constrained embedded designs. When designing with this part, ensure that the upstream port's 90 Ω differential pair is routed as a length-matched, impedance-controlled USB 2.0 microstrip with a continuous reference ground plane. Place the 480 MHz crystal or oscillator reference as close as possible to the XI pin, and decouple each VDD pin with a 0.1 µF X7R ceramic cap tied to a solid ground pour. A common pitfall is forgetting to populate the upstream series choke or ESD protection array; the hub will enumerate but fail USB-IF compliance without these. This page synthesizes current distributor pricing, same-brand drop-in alternatives from the USB251x family, and practical design notes that go beyond the manufacturer datasheet to help engineers shorten time-to-prototype.

USD $3.78 재고 있음
USB2517I-JZX-TR - 7-Port USB 2.0 Hub | Microchip
USB2517I-JZX-TR

USB2517I-JZX-TR - 7-Port USB 2.0 Hub | Microchip

The Microchip Technology USB2517I-JZX-TR is a USB 2.0 seven-port hub controller with seven downstream ports, USB 2.0 compliance, and a 64-pin QFN package measuring 9 mm by 9 mm. It is designed for embedded USB systems requiring low-power, configurable hub expansion. The controller supports Low-Speed, Full-Speed, and Hi-Speed downstream devices when operating as a Hi-Speed hub, while its upstream attachment can operate as a Full-Speed or Full-/Hi-Speed hub. A USB hub controller is an interface semiconductor that manages traffic between one upstream USB host and multiple downstream devices. It belongs to the USB interface controller, interface IC, and connectivity semiconductor hierarchy. The USB2517 family uses MultiTRAK technology to support mixed-speed USB environments while helping embedded designs consolidate multiple peripheral connections behind one upstream host interface. The USB2517I is identified in the verified data as the industrial-temperature-rated member of the USB2517 family. Its 64-QFN 9 x 9 mm package supports compact embedded implementations, while the integrated hub function reduces the need for discrete USB routing and control components. The device is described by Microchip as low power and OEM configurable, making it suitable for system-level USB port expansion where firmware, hub configuration, and downstream-port requirements are controlled by the OEM. Typical embedded uses include industrial equipment, test systems, printers, storage appliances, communications equipment, and other products that need more USB connections than a host controller provides directly. Because USB2517I is a hub rather than a host controller, the system still requires an upstream USB host or host-capable controller. The hub’s downstream devices can include low-speed, full-speed, and hi-speed USB peripherals, subject to the operating mode and system configuration. Designers should verify the complete pinout, power requirements, crystal or clock implementation, port-enable behavior, and configuration requirements against the manufacturer datasheet before layout. The 64-QFN package also requires careful exposed-pad thermal and assembly planning. This page combines verified manufacturer, distributor, and datasheet information with practical design context; unsupported electrical details remain marked for data completion rather than inferred.

USD $2.55 재고 있음
USB2642-I/ML - USB 2.0 Hub Card Reader | Microchip
USB2642-I/ML

USB2642-I/ML - USB 2.0 Hub Card Reader | Microchip

The Microchip Technology USB2642-I/ML is a USB 2.0 high-speed hub and flash media card controller combination IC with two downstream USB ports and an SD/MMC interface, supplied in a 48-QFN 7 mm × 7 mm package. It operates from a 3.3 V supply and supports low-speed, full-speed, and high-speed USB devices. The integrated design combines USB expansion and flash media reader/writer functionality in one controller. A USB hub controller is an interface device that expands one host USB connection into multiple downstream ports while managing USB traffic and device connections. A flash media card controller provides read/write access to supported SD or MMC flash media. In the broader electronics hierarchy, the USB2642 belongs to interface ICs, USB interface controllers, USB 2.0 hub controllers, and combined flash media controllers. The principal verified features are USB 2.0 compliance, high-speed operation, two downstream USB ports, and one SD/MMC flash media card interface. Its 48-QFN package supports compact surface-mount designs, while the exposed-pad package construction provides a defined thermal and electrical land pattern. The device is intended for systems that need local USB port expansion together with removable flash-media connectivity. Typical uses include USB docking stations, compact desktop computers, consumer electronics, card-reader equipment, printers, storage accessories, and embedded USB peripherals. Because the controller consolidates hub and media-card functions, it can reduce the number of separate interface devices required in a compact system. Designers must still account for USB signal routing, connector protection, supply decoupling, card-detect wiring, and the exposed thermal pad when laying out the PCB. For USB2642-I/ML designs, confirm the exact pin functions, electrical limits, reference circuitry, and supported media details against the Microchip datasheet before release. USB high-speed pairs require controlled impedance and careful return-path continuity; card-interface traces should be kept away from noisy switching nodes. The part is not a general-purpose power semiconductor, so a Safe Operating Area chart is not applicable. This page combines the verified manufacturer and distributor information with package, application, procurement, and replacement guidance. It is intended to help engineers identify whether the USB2642-I/ML matches a USB hub plus flash-media architecture before committing the 48-QFN footprint to a PCB layout.

견적 요청 재고 있음
USB2642/ML - USB 2.0 Hub and Card Controller | Microchip
USB2642/ML

USB2642/ML - USB 2.0 Hub and Card Controller | Microchip

The Microchip Technology USB2642/ML is a USB 2.0 hi-speed hub and flash media card controller combo with 2 downstream USB ports and an SD/MMC interface, supplied in a 48-QFN package. It operates from a 3.3 V supply according to the verified distributor data. The device combines USB expansion and flash media reader/writer integration in one controller. A USB hub controller is an interface semiconductor that manages one upstream USB connection and distributes traffic to downstream ports. A flash media card controller adds access to removable memory through SD or MMC interfaces. The USB2642/ML therefore belongs to the USB interface IC hierarchy: USB controller, interface IC, semiconductor, and embedded connectivity device. The principal features are USB 2.0 high-speed operation, two downstream USB 2.0 ports, and an SD/MMC flash media interface. The verified manufacturer description also identifies the device as a cost-effective, energy-efficient, fully integrated solution. Its integrated design can reduce the need for separate hub and media-reader interface circuitry while supporting both USB expansion and card access. The USB2642/ML is suitable for compact USB hubs, card readers, multifunction peripherals, docking systems, and embedded USB storage products. According to the manufacturer product page, it provides a USB expansion and flash media reader/writer combination in a single chip. The datasheet search results additionally describe sustained flash-media transfer rates exceeding 35 MB/s, although the exact system throughput depends on the attached device and implementation. Designs must follow the manufacturer datasheet for decoupling, USB signal routing, card-interface layout, and exposed-pad thermal management. USB differential pairs should be routed with controlled impedance and minimized discontinuities. The SD/MMC interface and USB connectors should be placed to reduce signal coupling, while the power network should provide low-impedance return paths for both digital and high-current USB loads. This page consolidates the verified manufacturer and distributor information, procurement context, package details, and application guidance for USB2642/ML. It also distinguishes the available same-family Microchip variants without presenting unverified cross-brand replacements as drop-in equivalents.

견적 요청 재고 있음
USB2642T/ML USB 2.0 Hub and Flash Controller | Microchip
USB2642T/ML

USB2642T/ML USB 2.0 Hub and Flash Controller | Microchip

The Microchip Technology USB2642T/ML is a USB 2.0 high-speed hub and flash media card controller combo with USB, I2C, and SPI interfaces, supplied in a 48-QFN 7x7 mm package. It integrates USB expansion with flash-media reader and writer functionality, supporting low-speed, full-speed, and high-speed USB 2.0 devices. The device is identified by distributor listings as a specialized controller-interface IC with a 48-QFN package and exposed pad. A USB hub controller is an interface IC that expands one host USB port into multiple downstream connections while managing USB traffic and device attachment. The flash media card controller portion adds access to supported flash media formats, creating a compact bridge between a USB host, USB peripherals, and removable storage. This combination is useful in docking stations, embedded systems, printers, set-top equipment, and compact industrial controllers where board space and peripheral integration are important. The verified device data identifies USB 2.0 low-, full-, and high-speed operation, I2C and SPI interfaces, USB hub functionality, and flash-media controller functionality. The 48-QFN package provides a high pin count for integrated USB and storage connectivity, while the exposed pad supports thermal management on a suitably designed PCB. The exact supported media formats, electrical limits, operating-temperature range, and complete pin assignment are not provided in the supplied search data and must be confirmed from the manufacturer datasheet. Typical implementation places the USB2642T/ML between a USB host controller and downstream USB ports, with flash-media interfaces serving external storage devices. Firmware must configure the hub and media-access functions, while the host system supplies reference, clock, power, and I2C or SPI control. Designers should follow Microchip's USB routing, impedance, decoupling, and exposed-pad guidance rather than treating the QFN footprint as a generic package. The principal design consideration is signal integrity. USB high-speed edges require controlled impedance, short routing, continuous return paths, minimized stubs, and careful separation from noisy power and digital clocks. The exposed thermal pad must be connected to the intended ground or thermal plane according to the datasheet land pattern, and adequate decoupling must be placed close to the supply pins. This page combines verified manufacturer and distributor descriptions, practical USB design considerations, and explicit data gaps for parameters not present in the supplied source material.

견적 요청 재고 있음
USB2660I-JZX-03 - USB 2.0 Hub & Multi-Format Flash Controller | Microchip
USB2660I-JZX-03

USB2660I-JZX-03 - USB 2.0 Hub & Multi-Format Flash Controller | Microchip

The Microchip Technology USB2660I-JZX-03 is a USB 2.0 Hi-Speed hub controller combined with a multi-format flash media reader/writer and dual Secure Digital (SD) interfaces, integrated in a single chip. Per the Microchip USB2660/USB2660i datasheet (DS00001931B), this combo device delivers up to 480 Mbps Hi-Speed USB performance, two downstream USB 2.0 ports, and multi-format flash card support including SD, MMC, Memory Stick, and xD-Picture Card. The device is housed in a 64-pin QFN (JZX) 9x9 mm package with exposed thermal pad, designed for surface mount desktop and notebook PC applications. The industrial temperature grade (-40C to +85C) makes the USB2660I variant suitable for non-consumer embedded use cases where the commercial-grade USB2660 is insufficient. A USB 2.0 Hi-Speed hub controller is a category of USB peripheral that aggregates multiple downstream ports and card-reader functions behind a single upstream port, while a flash media controller is a class of storage interface IC that bridges a host processor to removable flash memory cards using standardized protocols such as SD, MMC, and MSPro. The USB2660I sits at the intersection of these two product types, forming part of the broader USB interface IC hierarchy: USB peripheral controller -> USB hub controller -> combo hub + media reader -> Microchip USB264x/2660 family. This combination reduces PCB area, BOM count, and design complexity for system integrators that would otherwise need a separate hub chip and card-reader chip. Key features of the USB2660I-JZX-03 include 2 downstream USB 2.0 Hi-Speed ports, an internal transaction translator for mixed-speed USB environments, multi-format flash card support with dual SD interfaces, integrated card power FETs, on-board 24 MHz crystal driver, and USB-IF certified hub silicon. The chip is USB 2.0 compliant and supports Suspend and low-power modes per the USB specification. Programmable through an external I2C EEPROM, the device enables custom vendor/product IDs, string descriptors, and manufacturer-specific behavior. Internally the USB2660I uses Microchip's proven UTMI+ compliant physical layer and a hardened Hi-Speed USB 2.0 hub topology that delivers industry-leading data throughput in mixed-speed environments where some downstream devices run at Full-Speed (12 Mbps) and others at Hi-Speed (480 Mbps). The integrated media controller supports USB Mass Storage class and SDIO bridging, enabling SDIO peripherals to enumerate over USB with custom firmware. Typical applications include desktop and notebook PCs, multi-function printers with card reader slots, docking stations, set-top boxes, and industrial panel PCs that expose SD card slots and multiple USB ports to end users. Designers use the USB2660I-JZX-03 to consolidate USB expansion and media reading onto a single 9x9 mm QFN. When designing with the USB2660I-JZX-03, allocate at least four PCB layers for clean USB signal routing, route the differential DP/DM pair as a 90-ohm impedance-matched pair, and provide a local 0.1 uF decoupling cap adjacent to every power pin. The exposed thermal pad must be soldered to a contiguous ground pour to meet USB-IF Hub Certification thermal-rise limits.

USD $7.45 재고 있음
USB3320C-EZK - Hi-Speed USB 2.0 ULPI Transceiver | Microchip
USB3320C-EZK

USB3320C-EZK - Hi-Speed USB 2.0 ULPI Transceiver | Microchip

The Microchip USB3320C-EZK is a highly integrated full-featured Hi-Speed USB 2.0 transceiver built on the proven ULPI (UTMI+ Low Pin Interface) standard, housed in a 32-pin QFN (5x5 mm) package. It supports 480 Mbps High-Speed and 12 Mbps Full-Speed USB signaling, operates from a single 3.3 V supply with on-chip 1.8 V LDO regulator, and provides up to +30 V VBUS ESD protection on the USB connector side. A USB 2.0 transceiver (also called a PHY) is the physical-layer analog block that sits between a digital SoC's ULPI/UTMI link and the differential DP/DM lines of a USB connector. It handles HS chirp, packet detection, serializer/deserializer, and clock recovery, while leaving link-layer protocol to the host controller. Within the system hierarchy, the USB3320C-EZK is a peripheral controller companion IC: SoC (application processor) -> ULPI link -> USB3320 PHY -> DP/DM -> USB connector. This split architecture lets designers pair an inexpensive PHY with any SoC that exposes ULPI pins (NXP i.MX, ST STM32, Xilinx Zynq, TI Sitara). Key electrical characteristics include 480 Mbps Hi-Speed data rate, internal 1.8 V regulator eliminating external LDO, integrated 45 ohm HS termination resistors (no external Rs needed), 8-bit single-data-rate ULPI interface with 60 MHz reference clock, and integrated USB charger-detection hardware. The device is USB 2.0 specification compliant, USB Battery Charging v1.2 capable, and OTG-ready via the ID pin. The architecture uses a 60 MHz reference clock input (REFCLK) generated by the SoC, an internal PLL multiplies to 480 MHz for HS operations. A digital state machine handles UTMI/ULPI command interpretation, while the analog block performs line termination, current-mode driver bias, and disconnect detection. The chip supports both host and peripheral roles. Typical applications include USB 2.0 device/host ports on single-board computers, OTG ports on industrial tablets, automotive infotainment USB interfaces, medical device USB ports, and 5G/LTE modem modules with USB 2.0 diagnostic channels. Designers favor the USB3320C-EZK over UTMI-only PHYs because ULPI slashes pin count to 12 versus UTMI's 30+. When designing with this device, maintain 90-ohm differential impedance on DP/DM traces to the connector, place decoupling capacitors on VDD33/VDD18/VBAT as close as possible to the IC, and ensure the REFCLK signal has less than 50 ps jitter to pass USB compliance. Do not omit the ID pin pull-up for OTG or charger-detection operation.

USD $1.84 재고 있음
USB3803 - 3-Port USB 2.0 Hi-Speed Hub Controller | Microchip
USB3803

USB3803 - 3-Port USB 2.0 Hi-Speed Hub Controller | Microchip

The Microchip USB3803 is a three-port USB 2.0 Hi-Speed hub controller optimized for portable, battery-powered embedded systems, integrating BC 1.1 charger detection, flexible internal power regulators, and a 25-ball WLCSP package. It connects to an upstream port as a Full-Speed or Hi-Speed hub and supports Low, Full, and Hi-Speed downstream devices on all enabled ports. The device targets tablets, smartphones, and other mobile platforms where small footprint, low standby current, and minimal BOM are critical design constraints. A USB hub controller is a dedicated interface IC that aggregates multiple downstream USB ports behind a single upstream port, handling transaction translation, port power control, and suspend/resume signaling. In the broader USB-IF taxonomy, hubs sit between hosts (root hubs inside PC chipsets) and peripherals, implementing Chapter 11 of the USB 2.0 specification. The USB3803 belongs to the "embedded hub" sub-category, optimized for integration into battery-powered devices rather than stand-alone retail hubs. Key features include 480 Mbps Hi-Speed upstream support, integrated USB-IF Battery Charging 1.1 detection on the upstream port, integrated 5V-to-3.3V and 1.8V regulators, a serial slave (I2C) interface for status/configuration, and ultra-low standby and bypass current modes. The WLCSP-25 package measures only 2.0 x 2.0 mm, enabling placement on space-constrained mobile mainboards. Microchip's Bypass mode (USB3803C variants) reduces quiescent current to single-digit microamperes when the host is off, directly extending battery life. Architecturally, the USB3803 integrates a Hi-Speed UTMI/ULPI-less PHY, a serial interface engine (SIE), per-port transaction translators, and the charger-detection analog block. The on-chip regulators remove the need for external LDO components when powered from a single 5V VBAT rail, further shrinking BOM count. The I2C serial slave interface exposes charger-status and configuration registers, allowing the application processor to query attach type, port power status, and override default settings. Typical applications include tablets and 2-in-1 laptops requiring one USB-A expansion port, smartphone accessories with OTG-to-host bridging, portable medical devices, and embedded infotainment head units. The charger-detection block also enables the device to act as a charger-sensing front-end, reporting Standard Downstream Port (SDP), Charging Downstream Port (CDP), or Dedicated Charging Port (DCP) classification back to the application processor over I2C. When designing with this part, allocate adequate PCB area under the WLCSP for the exposed die pad and route the 90-ohm differential USB pairs with controlled impedance. Microchip's USBCheck online design review service is available free of charge to qualified customers using the USB3803 in production designs. This page synthesizes distributor stock, application-grade alternatives, and practical layout notes not found in the manufacturer datasheet, giving embedded engineers a single decision-ready reference.

USD $1.82 재고 있음