집적 회로

하위 카테고리

📁 ADC/DAC 3,100+ 제품 📁 증폭기 IC 1,900+ 제품 📁 오디오 코덱 18 제품 📁 오디오 IC 2 제품 📁 클록 및 타이밍 670+ 제품 📁 Comparator ICs 1 제품 📁 DSP 1,100+ 제품 📁 데이터 수집 IC 2 제품 📁 디지털 포텐셔미터 4 제품 📁 디스플레이 드라이버 및 컨트롤러 1 제품 📁 FPGA & CPLD 7,300+ 제품 📁 인터페이스 IC 3,400+ 제품 📁 LED 드라이버 1 제품 📁 로직 IC 460+ 제품 📁 메모리 IC 870+ 제품 📁 마이크로컨트롤러 20,000+ 제품 📁 마이크로프로세서 4 제품 📁 모터 드라이버 1 제품 📁 기타 1 제품 📁 Sensor and Detector Interfaces 1 제품 📁 특수 IC 15 제품 📁 비디오 IC 14 제품

제품 (39,000+)

LT1001CDR - Precision Op-Amp 8-SOIC | Texas Instruments (Tape & Reel)
LT1001CDR

LT1001CDR - Precision Op-Amp 8-SOIC | Texas Instruments (Tape & Reel)

The Texas Instruments LT1001CDR is a precision operational amplifier with industry-leading DC accuracy, supplied in an 8-pin SOIC (D) package. It features a maximum input offset voltage of 110 uV, a unity-gain bandwidth of 0.8 MHz, and a low offset voltage drift of 0.3 uV/C. The single-channel amplifier is built for instrumentation, precision signal conditioning, and industrial measurement front ends. A precision op-amp is a type of operational amplifier designed to minimize the input-referred errors (offset voltage, bias current, drift, and noise) that limit DC accuracy. In the system hierarchy, the LT1001CDR sits at the precision tier of general-purpose amplifiers, above standard 741-class parts and below chopper-stabilized zero-drift amplifiers. It is the workhorse of 16-bit and lower data-acquisition front ends, weigh scales, strain-gauge bridges, and thermocouple conditioning circuits where 10-100 uV of error must be resolved over industrial temperature ranges. Key features of the LT1001CDR include 110 uV maximum input offset voltage, 4 nA maximum input bias current, 102 dB minimum open-loop gain, and 0.3 uV/C offset voltage drift. The device operates from +/-3 V to +/-18 V dual supplies or 6 V to 36 V single supply. Its bipolar input stage supports true differential sensing across the full input common-mode range, including ground-referenced signals when operated from a single supply. The C-grade commercial temperature range is 0C to +70C. Architecturally, the LT1001CDR uses a precision bipolar input stage with active bias compensation, allowing it to maintain low offset and bias current over temperature without chopper-induced switching artifacts. The internal compensation network is unity-gain stable, eliminating the need for external compensation capacitors. The result is a versatile amplifier that combines 741-class simplicity with significantly tighter DC specifications. Typical applications include precision weighing scales, strain-gauge and load-cell amplifiers, thermocouple and RTD signal conditioning, medical instrumentation front ends, 16-bit SAR ADC input buffers, industrial process-control analog inputs, and reference-voltage buffering for precision DACs. The 8-SOIC package is footprint-compatible with industry-standard dual op-amps, simplifying board reuse in legacy designs. When designing with the LT1001CDR, take care to provide adequate supply decoupling (100 nF ceramic close to each supply pin) and route sensitive bias-current paths to avoid leakage. Optional pins 1 and 8 support external offset nulling via a 10 kOhm potentiometer; if unused, leave them open. The input common-mode range extends to the negative supply, making true ground sensing possible on a single rail. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone. The information is anchored to the official Analog Devices LT1001 datasheet and cross-checked against Rochester Electronics, DigiKey, and JAK Electronics stock data as of 2026-10-22.

견적 요청 문의하기
LT1001CH - 110dB Precision Operational Amplifier | Analog Devices
LT1001CH

LT1001CH - 110dB Precision Operational Amplifier | Analog Devices

Analog Devices LT1001CH is a precision operational amplifier featuring 700 pA input bias current, 110 dB open-loop gain, and operation from -3 V to +18 V, housed in an 8-pin TO-5 metal-can package. The LT1001 is designed for instrumentation and other signal-conditioning systems where low bias current, high gain, and low distortion are important. The CH ordering code identifies the commercial-temperature, 8-pin metal-can configuration. An operational amplifier is a high-gain differential-input amplifier that uses negative feedback to create stable, accurate gain in closed-loop circuits. Within the electronic-component hierarchy, the LT1001 belongs to the precision operational-amplifier family, which combines amplifiers with instrumentation amplifiers, analog signal-chain ICs, and semiconductor devices. Its principal role is to amplify small sensor or measurement signals while minimizing errors introduced by input bias current, offset voltage, and finite gain. The verified manufacturer information highlights three defining characteristics: 700 pA input bias current, 110 dB open-loop gain, and a -3 V to +18 V supply range. The 700 pA bias specification is especially relevant to high-impedance transducers because bias current creates an error voltage across source impedance. The 110 dB gain specification provides substantial open-loop margin for precision feedback networks. Dual-supply operation also allows bipolar input and output signals without requiring separate rail-to-rail biasing arrangements. The LT1001 data sheet describes the device as a precision operational amplifier whose distribution of key parameters was optimized during design, processing, and testing. That emphasis distinguishes it from general-purpose amplifiers in applications where predictable offset, bias current, gain behavior, and low-level signal fidelity matter. The TO-5 metal can offers an eight-pin mechanical format commonly encountered in precision laboratory and instrumentation equipment. Typical uses include low-level sensor front ends, bridge and strain-gauge signal conditioning, precision current-to-voltage conversion, laboratory instrumentation, and low-frequency measurement circuits. Its low 700 pA bias current can reduce loading of high-output-impedance sensors, while its 110 dB open-loop gain can improve closed-loop accuracy when the circuit operates with suitable feedback components and operating conditions. Designers should verify the exact eight-pin TO-5 pinout, offset-trim configuration, common-mode range, output-swing limits, and stability requirements against the manufacturer data sheet before replacing an existing amplifier. Input and feedback resistances must also be selected so their thermal noise and parasitic capacitance do not undermine the intended precision. Decoupling and grounding remain important even for a low-noise precision device because supply and return-path impedance can affect measured output performance. This page combines verified manufacturer and distributor information, package details, selection guidance, and a structured comparison of same-family drop-in options. It distinguishes known characteristics from parameters that still require confirmation from the official LT1001 data sheet, helping engineers evaluate replacement risk without relying on incomplete distributor summaries.

견적 요청 문의하기
LT1001CP - 110uV Offset, 0.8MHz Precision Op Amp | TI
LT1001CP

LT1001CP - 110uV Offset, 0.8MHz Precision Op Amp | TI

The Texas Instruments LT1001CP is a precision bipolar operational amplifier with maximum offset voltage of 110 uV, a 0.8 MHz gain-bandwidth product, and one amplifier circuit in an 8-pin PDIP package. The LT1001CP is positioned for instrumentation, sensor, and precision signal-conditioning applications that require low offset voltage and stable closed-loop amplification. An operational amplifier is an analog integrated circuit that uses high-gain differential amplification with negative feedback to produce an accurate output proportional to the difference between two input voltages. Within the broader semiconductor hierarchy, an operational amplifier belongs to amplifier ICs, analog and mixed-signal ICs, and power-management-adjacent signal-chain components. Its typical role is to buffer sensors, amplify small voltage differences, and drive downstream analog or digital circuitry. The verified LT1001CP specifications identify a maximum input offset voltage of 110 uV and a 0.8 MHz bandwidth. The low offset specification reduces the output error caused by unequal input voltages in a precision feedback circuit. The 0.8 MHz bandwidth establishes the device's useful small-signal operating range and makes the part appropriate for low-to-moderate-frequency measurement and control paths rather than high-speed signal processing. The LT1001CP uses bipolar construction and is packaged in an 8-pin PDIP. According to distributor records, the package is a rectangular, through-hole DIP with eight terminals and a stated body width of 0.300 inch, or 7.62 mm. Its through-hole construction supports prototyping, educational equipment, laboratory instrumentation, and industrial control boards where socketed assembly or manual rework is useful. Typical applications include precision bridge amplifiers, low-level sensor signal conditioning, laboratory measurement instruments, analog control loops, and general-purpose analog prototyping. The commercial temperature grade identifies the LT1001CP as a general-purpose commercial part. It is also suitable wherever the system can accommodate 0.8 MHz bandwidth and the electrical behavior of the LT1001 family. Designers should verify the complete manufacturer datasheet for supply voltage, input common-mode range, output swing, input bias current, slew rate, noise, supply current, and temperature limits before releasing a production design. Decoupling, grounding, source impedance, and feedback-component selection also determine practical precision more than the maximum offset rating alone. This page combines verified distributor pricing, a clear distinction between the target device and related LT1001 package or temperature options, and practical application guidance. It also identifies unavailable electrical data explicitly rather than estimating it, helping engineers compare the LT1001CP with the actual constraints of a specific analog circuit.

견적 요청 문의하기
LT1007CH - Low-Noise Precision Op Amp | Analog Devices
LT1007CH

LT1007CH - Low-Noise Precision Op Amp | Analog Devices

Analog Devices LT1007CH is a low-noise, high-speed precision operational amplifier in a TO-5 package. It provides 2.5 nV/√Hz wideband input noise, guaranteed 4.5 nV/√Hz noise at 10 Hz, guaranteed 3.8 nV/√Hz noise at 1 kHz, and a typical 60 nV peak-to-peak 0.1 Hz to 10 Hz noise figure. Its precision specifications include 10 µV offset voltage, 0.2 µV/°C drift, and 130 dB common-mode and power-supply rejection. These characteristics make the LT1007CH suitable for instrumentation, low-level sensor amplification, and precision signal chains where input-referred noise and DC stability are important. The LT1007 family combines low-noise operation with high-speed performance, while the LT1037 variant provides a 60 MHz gain-bandwidth product and is stable for closed-loop gains of 5 or greater. The LT1007CH is offered as a single, general-purpose amplifier circuit in a TO-5 package. The manufacturer's datasheet states that noise, precision, and speed are combined in one monolithic operational-amplifier family, supporting applications requiring both low-frequency noise performance and accurate signal amplification. Care should be taken with grounding, input lead routing, supply bypassing, and thermal management. The datasheet specifically advises minimizing air currents, keeping package leads short, placing the two input leads close together, and maintaining both inputs at the same temperature. Because the verified distributor data does not provide operating-voltage limits, supply current, input bias current, output swing, gain-bandwidth product for the LT1007, or detailed TO-5 pin assignments, those values are not asserted here. Consult the manufacturer datasheet for those parameters, input and output common-mode limits, saturation behavior, compensation requirements, and the exact pin configuration before final circuit design. The LT1007CH is a precision analog building block for equipment where low-noise, low-offset measurement paths are more important than minimum cost or maximum integration.

견적 요청 문의하기
LT1007CJG - Low-Noise Precision Op Amp | Texas Instruments
LT1007CJG

LT1007CJG - Low-Noise Precision Op Amp | Texas Instruments

The Texas Instruments LT1007CJG is a single, low-noise precision operational amplifier with 2.5 nV/√Hz wideband input-noise density, 10 µV offset voltage, and 0.2 µV/°C input-offset drift, packaged in an 8-pin CDIP. It combines low-noise performance with high open-loop gain and strong common-mode rejection for accurate analog signal conditioning. An operational amplifier is a voltage-feedback amplifier that uses high differential gain to amplify the difference between its non-inverting and inverting inputs. Within the wider signal-chain hierarchy, the LT1007CJG belongs to the precision amplifier class, which sits between general-purpose amplifiers and instrumentation amplifiers. Its noise and offset characteristics make it suitable when signals must be measured, converted, filtered, buffered, or referenced with little added error. The LT1007 series emphasizes low-noise signal handling with a 1/f noise corner frequency of 2 Hz and 60 nV peak-to-peak noise from 0.1 Hz to 10 Hz. The 10 µV input-offset voltage and 0.2 µV/°C drift limit input-referred error in slowly varying or high-gain stages. The amplifier also provides 130 dB common-mode rejection and power-supply rejection, reducing sensitivity to supply noise and shared ground-bus disturbances. A unity-gain-stable configuration supports direct signal buffering, while the instrumentation characteristics support precision gain stages. The device is intended for low-level sensor front ends, strain-gage and bridge excitation, precision current-to-voltage conversion, audio and low-frequency measurement circuits, laboratory instrumentation, and high-gain analog systems. Decoupling capacitors should be placed close to the supply pins so switching ripple and high-frequency supply variation do not modulate the output. For DC-sensitive applications, account for input-bias current of 55 nA when working with high-impedance sources. Because the CDIP package has eight through-hole leads, the amplifier fits conventional 0.300-inch, 7.62 mm row spacing and is easy to prototype or socket on laboratory and industrial boards. This page consolidates the LT1007CJG electrical characteristics, package details, design guidance, and drop-in family alternatives into a single engineering reference. Use the pin-description table and application information in the manufacturer datasheet when assigning PCB tracks, bypassing supply rails, and closing the loop around this amplifier.

견적 요청 문의하기
LT1007MLB - Low-Noise Precision Op Amp | Texas Instruments
LT1007MLB

LT1007MLB - Low-Noise Precision Op Amp | Texas Instruments

Texas Instruments LT1007MLB is a single-circuit, low-noise precision operational amplifier packaged in an 8-pin TO-99 metal-can package. The LT1007MLB is identified as a military-temperature-grade component with a through-hole, round-package construction and wire-form terminals. According to the manufacturer product page for the LT1007 family, the amplifier combines low-voltage noise with precision offset, drift, common-mode rejection, and power-supply rejection specifications. The family is specified with 10 µV offset voltage, 0.2 µV/°C offset drift, 130 dB common-mode rejection, and 130 dB power-supply rejection. An operational amplifier is an analog signal-conditioning IC that uses high-gain differential amplification to increase the voltage level of a low-amplitude input. Its wider role within analog electronics includes closed-loop gain, active filtering, instrumentation, buffer amplification, and feedback control. The LT1007 family is positioned for applications where low input noise, input-offset accuracy, and low drift are more important than compactness or low power consumption. Noise performance is a principal benefit of the LT1007 family. The manufacturer specifies 2.5 nV/√Hz wideband input noise, a 2 Hz 1/f corner frequency, and 60 nV peak-to-peak noise over the 0.1 Hz to 10 Hz band. These characteristics make the amplifier suitable for precision signal-chain work in which the amplifier must preserve weak signals without adding excessive broadband or low-frequency noise. The device is a single amplifier rather than a multi-channel integrated package. The precision specifications further distinguish the LT1007 from general-purpose amplifiers. A 10 µV input-offset voltage and 0.2 µV/°C drift support stable operation when source impedance, temperature, or input common-mode conditions vary. The specified 130 dB common-mode rejection ratio reduces output movement caused by common-mode input voltage, while 130 dB power-supply rejection reduces sensitivity to supply ripple. These specifications are particularly useful in measurement and control systems that require accurate amplification of small differential signals. Typical uses include precision sensor interfaces, low-level instrumentation, strain-gauge and bridge-amplifier signal paths, high-resolution measurement equipment, low-noise filter stages, and laboratory analog systems. The TO-99-8 package favors legacy instrumentation, military-style equipment, and prototypes where a through-hole metal-can package is convenient. Its physical size and eight terminals make it more appropriate for through-hole designs than compact mixed-signal equipment. Designers should account for the metal-can package, required supply rails, input-common-mode range, output swing, stability, and compensation requirements when assigning the amplifier. The LT1007 is not decompensated; the 60 MHz gain-bandwidth statement in the manufacturer material applies to the related LT1037, not automatically to LT1007MLB. Follow the manufacturer pin-description table when making PCB connections and verify the exact operating limits for the grade and suffix. This product overview combines the exact LT1007MLB package and ordering information with the manufacturer’s family-level precision, noise, rejection, and supply specifications. It also distinguishes directly verified device facts from parameters that require confirmation from the complete LT1007 datasheet.

견적 요청 문의하기
LT1007XH - Low-Noise 200°C Op Amp in TO-5 | Analog Devices
LT1007XH

LT1007XH - Low-Noise 200°C Op Amp in TO-5 | Analog Devices

Analog Devices LT1007XH is a single-circuit, low-noise operational amplifier specified for operation up to 200°C and supplied in a hermetic TO-5 package. It combines 10 µV offset voltage, 0.2 µV/°C offset drift, 130 dB common-mode rejection, and 130 dB power-supply rejection with monolithic noise performance of 2.5 nV/√Hz. The 1/f noise corner is 2 Hz, and 0.1 Hz-to-10 Hz noise is 60 nV peak-to-peak, making the device suitable for precision analog signal chains requiring low voltage noise and low drift. An operational amplifier, or op amp, is a high-gain differential amplifier used to amplify, buffer, filter, compare, or control analog signals. The LT1007 belongs to the precision operational-amplifier hierarchy, where low input noise, low offset drift, high rejection, and stable operation are more important than maximum bandwidth or minimum cost. Its wide operating-temperature capability extends that precision-focused role to industrial, instrumentation, and high-temperature analog systems. Key features include a 10 µV input offset voltage, 0.2 µV/°C input offset drift, and 130 dB common-mode rejection. The manufacturer describes a 2.5 nV/√Hz wideband noise density, a 2 Hz 1/f corner, and 60 nV peak-to-peak noise from 0.1 Hz to 10 Hz. The manufacturer datasheet also states that these devices are 100% tested at 200°C ±3°C, with normal operating-temperature specifications provided separately for the LT1007M version. The LT1007 series was designed as a direct replacement for the OP-27 operational-amplifier family, as stated in the manufacturer datasheet. This heritage is important because it provides an established precision-amplifier upgrade path for existing instrumentation and signal-conditioning designs. The LT1007XH combines the series noise and precision characteristics with a hermetic TO-5 construction intended to support demanding thermal environments. Typical uses include precision instrumentation, low-level sensor amplification, bridge and strain-gauge signal conditioning, laboratory measurement equipment, and industrial analog front ends. Its low-noise and low-drift characteristics are particularly valuable when the input signal is small and the useful measurement must remain stable despite temperature changes. In these applications, the amplifier is usually placed directly in front of an ADC or downstream measurement chain. When designing with the LT1007XH, verify the exact LT1007XH electrical limits from the manufacturer datasheet rather than substituting the normal-temperature LT1007M limits. Decoupling, input-bias-current compensation, source impedance, output loading, and stability must be evaluated around the selected noise and gain conditions. The hermetic package also requires attention to lead strain, thermal expansion, and PCB soldering practices. This page combines verified manufacturer specifications, current distributor sourcing information, same-package drop-in candidates, and practical selection guidance. It also distinguishes the uniquely tested LT1007XH temperature grade from ordinary package-code or reel-code variants, helping engineers make a replacement decision based on electrical compatibility and environmental requirements.

견적 요청 문의하기
LT1008CH - Picoamp Precision Operational Amplifier | Analog Devices
LT1008CH

LT1008CH - Picoamp Precision Operational Amplifier | Analog Devices

The Analog Devices LT1008CH is a single-circuit precision operational amplifier in an 8-lead round TO-5 hermetic package, combining picoampere input bias current, microvolt-level offset voltage, low noise, and very high common-mode and power-supply rejection. It operates from dual supplies up to ±18 V and can deliver 5 mA of load current, making it suitable for instrumentation, precision measurement, low-level signal conditioning, and current-to-voltage conversion. An operational amplifier is a high-gain differential amplifier whose output responds to the voltage difference between its non-inverting and inverting inputs. Negative feedback causes the amplifier to amplify only the signal presented within its linear operating range while rejecting common-mode voltage and supply-noise variations. Within the broader hierarchy, the LT1008CH is an instrumentation amplifier, an operational amplifier, an analog amplifier, a semiconductor, and ultimately a linear integrated circuit. The LT1008 family's defining characteristic is input bias current maintained in the picoampere range over the full -55°C to 125°C temperature range. This behavior makes the device useful with high-impedance sources, charge-sensitive transducers, leakage-sensitive sensors, and precision bridges where conventional CMOS or bipolar amplifiers may introduce unacceptable input-current error. The microvolt offset specification and low drift support stable DC measurements, while low voltage noise and current noise improve the useful resolution of small-signal chains. Extremely high common-mode rejection ratio and power-supply rejection ratio allow the LT1008 to reject interference coupled from the input source or from imperfect power-supply rails. These characteristics matter in systems where the signal of interest is small but supply noise and ground offsets are much larger. The manufacturer describes the device as a universal precision operational amplifier suitable for practically all precision applications. Typical uses include precision strain-gauge and bridge amplifiers, low-current pH and ion-selective measurement front ends, photodiode and charge-sensitive preamplifiers, laboratory references, low-leakage buffer stages, and precision current-to-voltage converters. The 8-lead TO-5 construction is mechanically robust and suited to laboratory, industrial, and instrumentation systems where through-hole mounting and hermetic construction are preferred. When designing around the LT1008CH, account for input-bias-current error in the feedback network, provide adequate supply bypassing at the pins, and use guarding to minimize leakage on high-impedance nodes. Because the device can operate from ±18 V, verify the complete circuit's absolute maximum voltages and ensure input common-mode limits are respected during startup and fault conditions. This page consolidates manufacturer specifications, sourcing information, application guidance, and design notes that are not consolidated in a single distributor listing.

견적 요청 문의하기
LT1010CH - ±150mA Fast Power Buffer | Analog Devices
LT1010CH

LT1010CH - ±150mA Fast Power Buffer | Analog Devices

The Analog Devices LT1010CH is a fast, unity-gain power buffer designed to increase the output-current capability of existing integrated-circuit operational amplifiers by more than an order of magnitude. The device is specified for output current up to ±150mA and is supplied in the TO-39, 3-lead metal-can package identified by the CH suffix. Its primary role is to buffer a low-current op-amp output while preserving high speed and reducing sensitivity to capacitive loading. A power buffer is an analog amplifier stage used between a precision or high-impedance signal source and a load that requires substantially more output current than the source can supply. In the signal-chain hierarchy, the LT1010 is a power buffer amplifier, which is a specialized type of voltage-feedback operational-amplifier output stage. The unity-gain configuration makes the buffered output follow the driving op-amp voltage closely while adding drive capability rather than voltage gain. Key verified characteristics include a nominal 20 MHz bandwidth and ±150mA output-current capability. The TO-39 package is a round, 3-terminal metal-can package with wire-form leads. According to the manufacturer datasheet, the LT1010 is intended to increase the output capability of existing op amps by more than an order of magnitude. This makes it useful when driving heavier capacitive, resistive, or current-intensive analog loads while retaining a relatively simple external circuit. The LT1010 is particularly relevant to precision DC amplifiers, instrumentation, signal-conditioning systems, and laboratory or industrial analog designs. Its fast behavior can improve transient response and make the driving amplifier less sensitive to capacitive loading. Unlike a discrete complementary output stage, the integrated device also reduces thermal feedback inside precision amplifier designs, according to the Analog Devices datasheet. The CH package should be checked carefully against the manufacturer pinout before PCB assembly because the TO-39 lead assignment and metal-can orientation are essential to correct operation. The verified web data identifies the package as TO-39-3 and describes the device as a 1-circuit buffer amplifier. The manufacturer product page also lists the LT1010 family in 8-pin miniDIP, plastic TO-220, and 8-pin DFN packages, but the CH ordering code is the metal-can TO-39 variant. When using the LT1010CH, verify the output-current rating, supply voltage, thermal conditions, stability requirements, and maximum output-voltage swing against the specific application. The TO-39 package requires attention to thermal dissipation and soldering profile. Because the output stage can source and sink substantial current, the load return path, bypassing, and grounding should be arranged to prevent large transient currents from disturbing sensitive analog nodes. This page combines the verified manufacturer datasheet, distributor identification, package information, and application guidance with practical selection, thermal, and circuit-layout considerations. It also distinguishes the verified LT1010CH characteristics from parameters that require confirmation in the complete manufacturer datasheet.

견적 요청 문의하기
LT1010CK - Fast ±150mA Power Buffer | Analog Devices
LT1010CK

LT1010CK - Fast ±150mA Power Buffer | Analog Devices

The Analog Devices LT1010CK is a fast, unity-gain power buffer capable of sourcing or sinking ±150 mA and is supplied in a TO-3 package. It is designed to increase the output-current capability of existing integrated-circuit operational amplifiers by more than an order of magnitude. The LT1010CK is particularly useful when an amplifier must drive heavier loads while maintaining fast response and reduced sensitivity to capacitive loading. A power buffer is a specialized amplifier stage placed between a low-current operational amplifier and a load. Its role in the signal-chain hierarchy is broader than ordinary voltage amplification: the upstream op-amp establishes gain and signal accuracy, while the buffer provides current drive, isolation, and improved load behavior. The LT1010CK operates as a unity-gain buffer, so its nominal signal gain is 1. This arrangement is commonly used in precision DC amplifiers, instrumentation systems, signal-conditioning circuits, and applications requiring more output current than a conventional op-amp can provide. The key feature of the LT1010CK is its fast, bipolar power-buffer architecture with ±150 mA output capability. According to the manufacturer datasheet, the device can increase the output capability of an existing IC op-amp by more than an order of magnitude. Its unity-gain configuration also makes the buffer less sensitive to capacitive loading and helps reduce thermal feedback in precision DC amplifier circuits. The manufacturer identifies the product as being in production. The LT1010 family is offered in multiple package options, including an 8-pin miniDIP, plastic TO-220 and 8-pin DFN packages. The low thermal resistance of the power package is intended to assist in reducing operating junction temperatures, although the LT1010CK’s wider TO-3-style package requires careful attention to heat dissipation and lead clearance. The datasheet specifically identifies the device as a fast ±150 mA power buffer. Typical applications include boosting the drive of precision operational amplifiers, driving high-current feedback networks, buffering instrumentation signals, and supplying greater output current into downstream stages. It can also improve the behavior of fast amplifier systems when capacitive loads would otherwise disturb the upstream amplifier. Its combination of speed, current capability, and unity-gain isolation makes it useful in laboratory, industrial control, and signal-conditioning equipment. Designers should verify the exact pin functions, electrical limits, thermal conditions, and stability requirements against the manufacturer datasheet before implementation. A power buffer must be checked for DC power dissipation, output-current direction, source-to-sink transitions, and the voltage and temperature limits of every connected stage. Layout should minimize parasitic feedback paths and maintain adequate thermal spreading around the power package. This page combines the verified manufacturer product information, distributor availability references, package identification, pricing information, and engineering guidance in one concise design resource. It also distinguishes documented LT1010 family options from true drop-in replacements, avoiding unsupported substitute claims where verified pin-compatible alternatives are not available.

견적 요청 문의하기
LT1011CH - Low-Power Precision Comparator | Analog Devices
LT1011CH

LT1011CH - Low-Power Precision Comparator | Analog Devices

Analog Devices LT1011CH is a general-purpose voltage comparator with low offset voltage, low input bias current, and low supply-current demand, housed in an 8-pin TO-5 metal package. Its guaranteed maximum input offset voltage is 0.5 mV, maximum input bias current is 25 nA, maximum input offset current is 3 nA, and input offset-voltage drift is guaranteed at 15 uV/°C. The LT1011CH is also pin compatible with devices in the LM111 series, simplifying qualification of a second-source design. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level output indicating which input is higher. The LT1011 belongs to the comparator hierarchy within interface and signal-conditioning semiconductors. Unlike an operational amplifier used primarily for closed-loop amplification, a comparator is optimized for rapid, deterministic output transitions and is commonly used in threshold detection, sensing, and control systems. The LT1011's principal advantage over the LM111 reference family is its improved input behavior. According to the Analog Devices manufacturer datasheet, it offers four times lower bias current, six times lower offset voltage, and five times higher voltage gain than the LM111. It also adds a guaranteed 15 uV/°C offset-voltage drift specification and reduces supply current. These characteristics make the part useful when comparator accuracy, input loading, or temperature stability has more importance than absolute switching speed. The LT1011CH provides an open-collector output, allowing the output to pull a logic rail low while an external pull-up resistor establishes the high state. This architecture supports wired logic, level translation, and wired-AND functions, but it also requires a pull-up resistor and suitable rise-time control. Input common-mode range, supply voltage, response time, and output sink-current limits should be checked against the manufacturer datasheet for the exact operating conditions. Typical uses include precision threshold detection, window comparison, sensor conditioning, relay or actuator control, and low-current digital interfacing. The low 25 nA maximum input bias current is especially useful with high-impedance sensors, while the 0.5 mV maximum offset voltage supports comparisons where input-level differences are small. The pin-compatible relationship with the LM111 series also allows existing LM111-based boards to be evaluated for an upgrade. For reliable implementation, connect the open-collector output to a suitable pull-up resistor, place it close to the receiving logic input, and keep sensitive input traces away from switching nodes. Account for input offset and drift when defining the decision threshold, and verify that the output pull-up voltage, sink current, supply voltage, and input common-mode limits satisfy the application. The exact operating limits must be taken from the manufacturer datasheet. This page combines the LT1011CH device specifications, package information, verified manufacturer and distributor links, same-footprint alternatives, and practical comparator design guidance. It also identifies where a drop-in decision requires additional qualification, especially for temperature grade, input performance, output timing, and automotive or industrial system requirements.

견적 요청 문의하기
LT1012CD - Precision Op Amp, 25µV Offset, 8-SOIC | Texas Instruments
LT1012CD

LT1012CD - Precision Op Amp, 25µV Offset, 8-SOIC | Texas Instruments

The Texas Instruments LT1012CD is a precision operational amplifier featuring 25 µV input offset voltage, 40 pA input bias current, and 200 µV typical offset in an 8-pin SOIC package. Originally designed by Linear Technology and now produced by Texas Instruments and authorized partners, the LT1012CD delivers picoampere-level bias currents over the full -55°C to +125°C temperature range with extremely high common-mode and power supply rejection ratios. A precision operational amplifier (op-amp) is a high-gain DC-coupled electronic voltage amplifier with a differential input and, usually, a single-ended output. Precision op-amps are characterized by low input offset voltage, low input bias current, low noise, and high common-mode rejection ratio (CMRR), making them suitable for amplifying small signals from sensors, transducers, and high-impedance sources. The LT1012 belongs to the broader category of linear integrated circuits and is positioned as a universal precision op-amp that combines the low-bias performance of BIFET/JFET-input amplifiers with the low-offset and low-drift characteristics of precision bipolar designs. Key features of the LT1012CD include 200 µV maximum input offset voltage, 40 pA maximum input bias current, 0.2 V/µs typical slew rate, and the ability to deliver 5 mA of output current while maintaining a voltage gain of one million. The device operates over a wide supply range (typically ±2 V to ±20 V) and offers extremely high CMRR and PSRR, with practically unmeasurable warm-up drift, making it ideal for precision instrumentation. The LT1012CD uses Linear Technology's advanced bipolar process technology that achieves sub-picoampere bias currents through active bias-current cancellation, while the precision bandgap-based input stage provides the low offset and low drift. The amplifier is internally compensated, eliminating the need for external compensation components in most applications, simplifying PCB layout and reducing BOM cost. Typical applications include precision thermocouple amplification, strain-gauge and weigh-scale signal conditioning, medical instrumentation, high-impedance sensor buffers, precision integrators for analog computation, and battery-powered portable instrumentation where the LT1012 achieves precision operation on two Ni-Cad batteries with only 1 mW of power dissipation. When designing with the LT1012CD, note that its 0.2 V/µs slew rate makes it suitable for DC and low-frequency signals but inadequate for high-speed or wide-bandwidth applications. For those applications, a faster op-amp such as the LT1028 or OP-27 should be considered. Standard 8-SOIC layout conventions apply, with input pins (IN+, IN-) at pins 3 and 2, output at pin 6, and power pins at pins 7 (V+) and 4 (V-). This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that go beyond the manufacturer datasheet to support fast engineering decisions.

견적 요청 문의하기
LT1012CH - Picoamp Precision Op Amp | Analog Devices
LT1012CH

LT1012CH - Picoamp Precision Op Amp | Analog Devices

Analog Devices LT1012CH is a single-circuit, internally compensated precision operational amplifier with picoampere input bias current, microvolt offset voltage, low voltage noise, low current noise, and very high input impedance. It operates from a single positive supply and can provide a closed-loop voltage gain of one million while delivering a 5 mA load current. The device is offered in an 8-lead round TO-5 metal-can package with wire-form leads. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The LT1012 belongs to the precision operational-amplifier hierarchy, combining high open-loop gain with low offset, low bias current, and low-noise behavior. These characteristics make it useful when the source impedance can be high enough that input bias-current error would overwhelm a conventional amplifier. The LT1012's principal features include picoampere bias currents maintained across the full -55°C to +125°C temperature range, microvolt offset voltage, low offset drift with time and temperature, and exceptionally high common-mode and power-supply rejection ratios. According to the manufacturer, precision operation on two Ni-Cad batteries is possible with 1 mW of power dissipation. The reported 5 mA load-current capability and gain of one million are particularly useful for precision buffer, instrumentation, transducer, and low-level signal-chain applications. The LT1012 is implemented as a bipolar precision amplifier and is internally compensated for unity-gain stability. This architecture supports simple voltage-follower use without external compensation while retaining accurate low-frequency operation. The high gain and very low input current also make the device suitable for guarding, electrochemical measurement, photodiode amplification, and other applications where source leakage and offset can dominate measurement accuracy. Typical uses include precision sensor interfaces, low-current transducers, battery-powered instruments, pH and conductivity measurement circuits, photodiode amplifiers, and analog test equipment. The hermetic metal-can package provides a mechanically robust option for applications requiring stable operation over an extended temperature range, although engineers should observe the manufacturer's specified lead orientation and connection requirements. When using the LT1012CH, minimize leakage around the input pins and keep sensitive input traces away from power and ground paths. Because very high open-loop gain makes offset, bias-current error, and leakage especially important, clean PCB surfaces, guarded inputs, suitable bypassing, and careful source-impedance balancing are essential. This page combines verified manufacturer and distributor information with practical implementation guidance and clearly identified drop-in alternatives.

견적 요청 문의하기
LT1013CD - Dual Precision 1MHz Op Amp | Texas Instruments
LT1013CD

LT1013CD - Dual Precision 1MHz Op Amp | Texas Instruments

The Texas Instruments LT1013CD is a low-power dual precision operational amplifier with a 4 V to 44 V supply range, 1 MHz gain-bandwidth product, 0.4 V/us slew rate, and two amplifiers in an 8-pin SOIC package. The device combines high gain, low noise, low supply current, and low-offset-voltage temperature coefficient in one circuit. According to the Texas Instruments product page, LT1013CD is the lead-free SOIC orderable version of the LT1013 family. An operational amplifier is an analog signal-processing semiconductor that uses high open-loop gain to amplify voltage differences accurately. Within the broader hierarchy, an operational amplifier is a linear amplifier, analog IC, and signal-conditioning component. The LT1013 fits precision instrumentation because its dual configuration supports common differential, summing, filtering, threshold, or transimpedance stages while reducing board area. Verified product information identifies high gain, low noise, low supply current, and a low-offset-voltage temperature coefficient as principal family characteristics. The device can operate from a single 5 V supply, has a common-mode input range that includes ground, and produces output swings to within a few millivolts of ground, as stated in the supplied comparison-source material. These properties are useful in battery-powered measurements where larger supply headroom would be inconvenient. The LT1013 family supports broad supply operation from 4 V to 44 V, allowing the same precision amplifier architecture to serve low-voltage instrumentation and higher-voltage industrial signal chains. Its 1 MHz gain-bandwidth product supports moderate-bandwidth closed-loop functions rather than high-speed waveform or communications applications. The 0.4 V/us slew rate likewise favors low-frequency precision conditioning over wideband pulse acquisition. Analog Devices lists battery-powered precision instrumentation, strain-gauge signal conditioners, thermocouple amplifiers, instrumentation amplifiers, 4 mA to 20 mA current-loop transmitters, multiple-limit threshold detection, and active filters as representative LT1013 applications. These uses benefit from dual-channel operation, low supply current, precision behavior, and the ability to work across single and split supplies. When designing with the LT1013CD, preserve the required bypass capacitance, maintain common-mode and output headroom, and confirm that closed-loop bandwidth matches the 1 MHz family characteristic. Check noise, offset, supply current, and common-mode limits against the actual precision requirements. Pricing shown for LCSC is $0.4097 as of 2026-10-22; other distributor prices and current stock must be confirmed at purchase. This page combines verified manufacturer and distributor information, packaging details, applications, pricing context, and engineering guidance. It also identifies which parameters remain unavailable in the supplied evidence instead of estimating them, enabling engineers to make a more defensible LT1013CD selection.

견적 요청 문의하기
LT1013CJG - Dual Precision Op Amp, 300uV Offset, CDIP-8 | Texas Instruments
LT1013CJG

LT1013CJG - Dual Precision Op Amp, 300uV Offset, CDIP-8 | Texas Instruments

The Texas Instruments LT1013CJG is a dual precision operational amplifier with 300 uV maximum input offset voltage, a 0.7 MHz gain-bandwidth product, and a hermetically sealed 8-pin ceramic DIP (CDIP-8) package with 0.300 inch lead pitch. Two amplifiers share one hermetic package, giving instrument-grade amplification in strain-gauge, thermocouple, and 4 mA to 20 mA current-loop signal chains. An operational amplifier (op amp) is a high-gain differential amplifier whose inverting and non-inverting inputs are compared, with feedback defining the closed-loop gain. A precision op amp is a variant optimised for low input offset voltage, low input bias current, and low drift so that small sensor signals are amplified without adding meaningful error. Within the component hierarchy, the LT1013CJG sits as a voltage-feedback amplifier in the family of amplifier ICs, inside the broader class of analog integrated circuits and power-management-adjacent signal-chain devices. Key specifications include a 300 uV maximum input offset voltage, 0.7 MHz gain-bandwidth product, and dual-amplifier configuration in a single hermetic ceramic DIP. The device operates from ±15 V supplies as well as from a single 5 V supply, and it exposes two offset-null pins so that input offset voltage can be trimmed in the circuit rather than accepted as a fixed error. Hermetic ceramic sealing protects the die from moisture and contaminants, which matters in high-reliability and legacy industrial equipment. Architecturally the LT1013CJG is a conventional bipolar voltage-feedback amplifier, which gives it wide supply-voltage swing, low input bias current, and predictable AC behaviour with a single compensation capacitor rather than the auto-zeroed architecture used in chopper-stabilised parts. The result is very low noise at low frequencies with continuous operation across the input range, at the cost of higher offsets than modern auto-zeroed amplifiers. Typical applications include bridge and strain-gauge signal conditioners, thermocouple amplifiers, precision instrumentation amplifiers, 4 mA to 20 mA current-loop transmitters, multiple-limit threshold detection, active filters, and multi-stage gain blocks in battery-powered precision instruments. When designing around this device, use the two offset-null pins for trimming and place the compensation capacitor close to the device. Keep the hermetic package away from thermal sources, because gradient across the ceramic can shift offset voltage, and avoid saturating the output near the supply rails in instrumentation front ends. This page combines manufacturer and distributor technical data, drop-in alternatives, comparison parameters, and practical design guidance that are not consolidated in the original datasheet.

견적 요청 문의하기
LT1013CP - Dual Precision Op Amp, 4-44V | Texas Instruments
LT1013CP

LT1013CP - Dual Precision Op Amp, 4-44V | Texas Instruments

The Texas Instruments LT1013CP is a dual precision operational amplifier featuring high gain, low supply current, low noise, and a low offset-voltage temperature coefficient, supplied in an 8-pin PDIP (P) package. It operates from a single 4V to 44V supply (or dual ±2V to ±22V supplies), draws only 0.5 mA typical supply current per amplifier, and delivers 150 µV maximum input offset voltage at 25°C (LT1013A grade). The input common-mode range includes ground and the output swings to within a few millivolts of ground while sinking current, eliminating crossover distortion. A dual precision op amp is a two-channel integrated operational amplifier that combines matched transistor pairs and laser-trimmed thin-film resistors to achieve DC accuracy comparable to chopper-stabilized designs while consuming milliwatts of power. Within the broader component taxonomy, dual op amps sit under operational amplifiers -> amplifiers -> analog ICs -> semiconductor. The LT1013 was the first precision dual op amp in the 8-pin industry-standard pinout, upgrading legacy devices such as the MC1458/MC1558, LM158, and OP-221 with significantly lower noise and better DC stability. Key features include 150 µV max input offset voltage (LT1013A) with 2.5 µV/°C max offset voltage temperature coefficient, 0.5 mA typical supply current per amplifier, single-supply operation from 4V to 44V, ground-sensing input range, and output swing to within millivolts of ground. The NPN input stage delivers low input bias current and low voltage noise density suitable for transducer and instrumentation front-ends. Typical applications include battery-powered precision instrumentation, strain-gauge signal conditioners, thermocouple amplifiers, 4 mA to 20 mA current-loop transmitters, active filters, multiple limit threshold detection, and instrumentation amplifier building blocks. The wide supply range and ground-sensing inputs make it ideal for single-supply industrial and process-control systems. When designing with this part, observe the input common-mode limit: although the inputs include ground, the upper common-mode limit is approximately 1.5V below the positive rail. Place a 0.1 µF bypass capacitor close to the supply pin and add a 10 µF bulk capacitor on the supply rail to maintain low-impedance power across the LT1013's full bandwidth.

견적 요청 문의하기
LT1013DD - Dual Precision 5V-44V Op Amp | Texas Instruments
LT1013DD

LT1013DD - Dual Precision 5V-44V Op Amp | Texas Instruments

The Texas Instruments LT1013DD is a low-power dual precision operational amplifier with a 5 V to 44 V wide supply range, two amplifier channels, and an 8-pin SOIC (D) package. The device is intended for instrumentation, signal-conditioning, filtering, and threshold-detection circuits that operate from low single-supply voltages through substantially higher industrial supply levels. Its precision-oriented design combines high gain, low supply current, low noise, and low offset-voltage temperature coefficient, while the extended supply range supports both single-supply and dual-supply implementations. An operational amplifier is an active analog signal-processing device that uses feedback to amplify the difference between its inverting and non-inverting inputs. The dual LT1013 provides two amplifiers in one package, allowing designers to implement two signal paths without using separate packages. In the broader semiconductor hierarchy, the LT1013DD is an analog integrated circuit, specifically a precision operational amplifier used within instrumentation and embedded signal-conditioning systems. The verified product information identifies the LT1013DD as a standard general-purpose dual amplifier with an 8-SOIC package and a 0 °C to 70 °C operating-temperature range. The TI product-page snippet describes the LT1013D as a low-power device with a 5 V to 44 V wide supply range. The wider LT1013 product page states a 4 V to 44 V supply range, so the exact minimum operating supply for the selected LT1013DD ordering option should be confirmed against the manufacturer datasheet before design release. The LT1013DD is suited to battery-powered precision instrumentation, strain-gauge signal conditioners, thermocouple amplifiers, instrumentation amplifiers, 4 mA-to-20 mA current-loop transmitters, multiple-limit threshold detection, active filters, and multiple gain blocks. Its dual-channel configuration is useful where two related signals must be conditioned consistently, such as sensor excitation and monitoring or differential and common-reference measurements. Designers should pay particular attention to the SOIC-8 pin mapping, supply bypass capacitors, input common-mode range, output swing, and the operating-temperature limits for this ordering code. The precision characteristics make the device useful for instrumentation, but they do not make it a universal rail-to-rail amplifier. Verify signal levels, noise requirements, load conditions, and stability requirements against the manufacturer datasheet rather than assuming that a substitute is electrically identical. This product page consolidates the verified manufacturer and distributor information, source-backed alternatives, package details, pricing fields, application guidance, and design notes. It is intended to support initial component selection and comparison rather than replace the complete LT1013D datasheet during sign-off.

견적 요청 문의하기
LT1013DP - Dual Precision Op Amp, 4-44V, 8-PDIP | TI
LT1013DP

LT1013DP - Dual Precision Op Amp, 4-44V, 8-PDIP | TI

The Texas Instruments LT1013DP is a dual precision operational amplifier with a low-power, wide 4 V to 44 V supply range, supplied in an 8-pin PDIP package. The device provides two amplifier circuits in the standard dual-op-amp configuration and is designed for instrumentation and precision signal-conditioning applications. According to the TI product page, the LT1013 family is specified for ±15 V and single 5 V supply operation, while the LT1013D version supports single-supply operation with input voltage range extending to ground and output swing to ground while sinking current. What is a precision operational amplifier? A precision op amp is a voltage-feedback amplifier used to amplify small differential signals while controlling offset, bias current, drift, and output behavior. Within the signal-chain hierarchy, the LT1013DP is a dual amplifier IC that can serve as an instrumentation amplifier building block, a buffer, an active-filter element, or a precision gain stage. Its dual channel count allows two signal paths or a differential signal-conditioning structure in one package. Key verified features include a 4 V to 44 V supply range, dual precision operation, and the industry-standard 8-pin configuration identified by Analog Devices as the first precision dual op amp in that configuration. The LT1013DP is listed by DigiKey as a two-circuit, 8-PDIP amplifier. The Analog Devices product page specifically identifies battery-powered precision instrumentation, strain-gauge signal conditioners, thermocouple amplifiers, instrumentation amplifiers, 4 mA to 20 mA current-loop transmitters, multiple-limit threshold detection, active filters, and multiple-gain blocks as application areas. The LT1013DP is especially relevant where a low-power amplifier must operate across a broad supply range or support single-supply signal paths whose input and output approach ground. Compared with a conventional dual precision amplifier in a different package, its 8-PDIP format favors through-hole prototyping, educational platforms, legacy industrial equipment, and repair assemblies where pin compatibility and mechanical replacement matter. The product family is not limited to ±15 V operation; the verified product description confirms single 5 V operation as well. The principal design trade-off is that a PDIP package is larger and less suitable for high-density surface-mount assemblies than a modern small-outline package. Designers should still verify the exact ordering variant, pinout, common-mode limits, output swing, input bias current, offset voltage, drift, noise, and supply-current limits against the manufacturer datasheet before production release. The verified product family is described as low power, but the precise quiescent-current value is not supplied in the provided web data and should be treated as [DATA_NEEDED: quiescent current]. This page synthesizes the verified LT1013 family descriptions, distributor identification, package information, application references, and cross-reference search results. It distinguishes exact verified facts from parameters that require the full manufacturer datasheet, helping engineers evaluate the LT1013DP for precision instrumentation, bridge sensing, thermocouple signal conditioning, current-loop transmission, filtering, and legacy through-hole amplifier designs.

견적 요청 문의하기
LT1013IP - Dual Precision Low-Power Op Amp | Texas Instruments
LT1013IP

LT1013IP - Dual Precision Low-Power Op Amp | Texas Instruments

The Texas Instruments LT1013IP is a dual precision low-power operational amplifier with two amplifier circuits, a bipolar input stage, and an 8-pin PDIP package. It operates from a 4 V to 44 V supply range and is intended for instrumentation, signal-conditioning, and low-power analog systems. The verified distributor data identifies a maximum offset voltage of 550 uV, single-supply input operation extending to ground, and output swing toward ground while sinking current. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its differential inputs. The LT1013 belongs to the precision operational-amplifier hierarchy, where low offset voltage and low input bias currents support accurate signal conditioning rather than general switching or high-current drive. Its dual configuration provides two amplifiers in one package, reducing board area when a system needs matched gain stages, buffers, comparators, or active filters. The LT1013IP combines low-power operation with precision-oriented performance. Its wide 4 V to 44 V supply capability makes it useful in industrial instrumentation, battery-powered measurement systems, process-control equipment, and signal-chain modules that operate from elevated supply voltages. The ability to accept inputs near ground supports single-supply measurement circuits, while the ground-referenced output capability supports low-level sensor and current-loop interfaces. The device uses a bipolar input architecture. Compared with rail-to-rail-input amplifiers, the architecture emphasizes precision over operation immediately adjacent to the positive supply rail. Designers should therefore verify the common-mode input range, output swing, load capability, and supply limits against their particular feedback network. The 550 uV maximum offset value reported for the LT1013IP is relevant to sensor-amplifier designs because input offset voltage can become a meaningful error after substantial signal gain. Typical applications include strain-gauge signal conditioning, thermocouple amplification, instrumentation stages, 4 mA-to-20 mA current-loop transmitters, active filters, threshold detection, and multiple gain blocks. Battery-powered precision instrumentation is particularly suitable because the part is identified as a low-power dual operational amplifier while retaining a broad supply range for laboratory, industrial, and communications equipment. For stable operation, place the input and feedback components close to the device, use suitable bypassing at the supply pins, and verify operation across the complete input, output, load, and temperature ranges. Input common-mode and output swing limits must be checked at the lowest and highest expected supply voltages. Negative supply operation may also be available in specific configurations, but the exact operating conditions must be confirmed in the manufacturer datasheet. This page consolidates verified manufacturer and distributor information, pin-compatible alternatives, application guidance, and practical design considerations. It also separates confirmed LT1013IP attributes from electrical parameters that require datasheet verification, helping engineers make sourcing and design decisions without treating unverified values as product facts.

견적 요청 문의하기
LT1014CJ - Quad Precision Op Amp, 50 uV Offset | Analog Devices
LT1014CJ

LT1014CJ - Quad Precision Op Amp, 50 uV Offset | Analog Devices

Analog Devices LT1014CJ is a four-channel precision operational amplifier with 50 uV input offset voltage, 0.3 uV/°C offset drift, 117 dB common-mode rejection, and 120 dB power-supply rejection, housed in a 14-pin CERDIP package. It operates from dual ±15 V or single 5 V supplies and supports input and output operation down to ground. A precision operational amplifier is a voltage-feedback amplifier designed to amplify small signals accurately while minimizing offset, drift, bias-current error, and power-supply coupling. The LT1014 belongs to the operational-amplifier hierarchy within analog and linear ICs, providing four amplifiers in one package for instrumentation, signal-conditioning, filtering, and threshold-detection circuits. Key features include 50 uV offset voltage, 0.3 uV/°C offset drift, 0.15 nA offset current, an open-loop gain of 8 million, and low supply current of 350 uA. Its 117 dB CMRR and 120 dB PSRR help preserve accuracy when the input signal is small relative to the supply rails. The input common-mode range extends to ground, while the output can swing to ground while sinking current. The LT1014 architecture provides precision performance in four independent amplifier channels. Unlike general-purpose quad amplifiers, its low offset and drift reduce calibration requirements in battery-powered instrumentation, strain-gauge conditioning, thermocouple amplification, current-loop transmitters, active filters, and multiple-limit threshold detection. The manufacturer identifies operation with both ±15 V and single 5 V supplies. The same 14-pin industry-standard configuration as the MC1458/LM348/OP-11/4156 families simplifies upgrades where precision specifications are required. The LT1014CJ is particularly relevant to low-level sensor interfaces where error from input offset or supply variation would otherwise dominate the measurement chain. Designers should verify common-mode and output-swing limits over the complete temperature range, provide suitable bypassing around the supply pins, and account for input-bias-current error when using high-impedance sensors. Exact temperature limits, noise density, slew rate, and package dimensions are not stated in the supplied web data and therefore require confirmation from the manufacturer datasheet. This page combines manufacturer specifications, verified distributor availability, package and pinout information, drop-in family alternatives, application guidance, and transparent data gaps. These engineering-oriented details help buyers assess replacement risk without treating a similar amplifier as automatically equivalent.

견적 요청 문의하기
LT1014CN - 4-Channel 5V-44V Precision Op Amp | Texas Instruments
LT1014CN

LT1014CN - 4-Channel 5V-44V Precision Op Amp | Texas Instruments

The Texas Instruments LT1014CN is a four-channel precision operational amplifier with a 5 V to 44 V total supply range, 1 MHz gain-bandwidth product, and 14-pin PDIP package. It supports single 5 V operation and dual ±15 V operation, while its input common-mode range includes ground. The device is intended for low-power precision instrumentation, battery-powered measurement systems, strain-gauge amplifiers, thermocouple amplifiers, current-loop transmitters, threshold detectors, and active filters. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. When negative feedback is applied, the closed-loop circuit determines the gain and bandwidth. The LT1014 belongs to the precision operational-amplifier hierarchy, where low offset voltage, low temperature drift, low noise, and low supply current are important for preserving the integrity of small sensor signals. Four amplifiers are integrated into one 14-pin DIP, reducing board area compared with four separate single or dual packages. The LT1014CN provides an input offset voltage of 300 µV maximum at 25 °C and an input offset voltage temperature coefficient of 2.5 µV/°C maximum for the LT1014 family. Its 1 MHz gain-bandwidth product and 0.4 V/µs slew rate support general-purpose precision signal conditioning. Its low-power architecture and 5 V single-supply compatibility are useful when supply energy is constrained. The common-mode input range extends to ground, allowing the device to process signals close to the lower supply rail. The LT1014 uses an industry-standard 14-pin quad operational-amplifier configuration, with four complete amplifier sections and a no-connect position on pin 8. This arrangement supports straightforward printed-circuit-board layout in the familiar PDIP footprint. The device can be used without external compensation in ordinary closed-loop configurations, although gain, noise, output swing, load capability, and stability should be evaluated for each application. Its precision characteristics are more useful than a general-purpose amplifier when sensor outputs are small and drift matters over time. Typical applications include bridge-based strain and pressure measurement, thermocouple signal conditioning, precision current-loop receivers, low-level active filters, multiple-threshold detection, and battery-operated instrumentation. The four independent channels can process several related signals in one package, such as four transducer outputs or a mixed set of amplification, filtering, and comparison functions. The LT1014CN is also useful when both positive and negative supplies are available, because it can operate at dual ±15 V while retaining precision operation. Designers should verify input and output voltage limits, load current, common-mode range, noise, and stability against the worst-case supply voltage and temperature. Input and output decoupling should be placed close to the relevant supply pins, and unused amplifier sections should be configured according to the manufacturer recommendations rather than left floating. Because the package is a PDIP rather than a surface-mount package, it also requires adequate spacing for through-hole assembly and appropriate lead-bend clearance. This product record combines verified manufacturer and distributor information, same-footprint alternatives, pricing status, and practical selection guidance. It highlights the LT1014CN's 5 V to 44 V supply range, four precision channels, 1 MHz bandwidth, 300 µV offset limit, and 14-pin PDIP footprint to support faster engineering selection than a distributor listing alone.

견적 요청 문의하기
LT1014DN - Quad Precision Op Amp, 14-PDIP | Texas Instruments
LT1014DN

LT1014DN - Quad Precision Op Amp, 14-PDIP | Texas Instruments

The Texas Instruments LT1014DN is a quad precision operational amplifier in a 14-pin PDIP through-hole package, featuring low offset voltage of 50 µV, 0.3 µV/°C offset drift, and 8 million typical open-loop gain. The device operates from a 5V to 44V wide supply range and supports both dual ±15V and single 5V rails, making it one of the most flexible precision quads for instrumentation designs. An operational amplifier is a high-gain DC-coupled electronic voltage amplifier with differential inputs that produces an output potential relative to ground. Precision op amps such as the LT1014 family are characterized by very low input offset voltage, low bias current, low noise, and high common-mode rejection ratio (CMRR). Within the broader taxonomy, the LT1014 sits at the intersection of instrumentation amplifiers and general-purpose amplifiers, positioned above simple comparators but below specialized zero-drift or chopper-stabilized amplifiers. Its four channels per package make it a workhorse for multi-channel signal conditioning where matched channel-to-channel DC behavior is required. Key specifications include 50 µV maximum offset voltage, 0.3 µV/°C offset drift, 0.15 nA offset current, 117 dB CMRR, 120 dB power supply rejection ratio (PSRR), and a guaranteed 500 µA maximum supply current per amplifier. The output stage swings to within millivolts of both rails, and the common-mode input range includes the negative supply (ground in single-supply operation). Noise performance is 0.55 µV peak-to-peak from 0.1 Hz to 10 Hz, making the LT1014 well-suited for low-frequency precision applications. The LT1014 architecture uses bipolar junction transistor input stages with laser-trimmed thin-film resistors to achieve low offset without external nulling. Notably, no offset null terminals are provided in the quad configuration, which is why the factory-trimmed 50 µV maximum is critical. The combination of low supply current (350 µA typical per amplifier) and 5V minimum supply makes the LT1014 unusually capable for both line-powered instrumentation and battery-powered precision circuits. Typical applications include 4-20 mA current loop transmitters, strain gauge signal conditioners, thermocouple amplifiers, multiple limit threshold detection, active filters, and battery-powered precision instrumentation. The 14-pin PDIP package is favored for breadboard prototyping, laboratory instrumentation, and through-hole industrial designs where socket replacement is desirable. When designing with the LT1014DN, observe that no offset null pins are present, so system offset must be tolerated or corrected downstream. The 14-PDIP package has higher thermal resistance than surface-mount equivalents, so multi-amp loads at high supply voltages may require derating. For new designs where SMT is acceptable, consider the LT1014DSW or similar surface-mount variants. This page synthesizes distributor pricing, drop-in compatible alternatives, and practical design notes not found in a single manufacturer datasheet, with cross-references curated for engineers evaluating multi-channel precision analog front ends.

견적 요청 문의하기
LT1014IN - Quad Precision Op Amp, 5V-44V | Texas Instruments
LT1014IN

LT1014IN - Quad Precision Op Amp, 5V-44V | Texas Instruments

The Texas Instruments LT1014IN is a quad precision operational amplifier with four amplifiers in a 14-pin DIP package, operating from a 5 V to 44 V supply range. It is designed for precision instrumentation, signal conditioning, battery-powered measurement, active filtering, and current-loop interfaces. The device is specified for low offset voltage, low offset-voltage temperature coefficient, high open-loop gain, high common-mode rejection, high power-supply rejection, low supply current, and low noise. According to the Analog Devices data sheet, the LT1014 family provides 50 uV offset voltage, 0.3 uV/°C drift, 8 million gain, 117 dB CMRR, 120 dB PSRR, and approximately 350 uA supply current. The LT1014IN uses the industry-standard 14-pin quad operational-amplifier configuration, making it useful for designs requiring four precision amplifier sections without using four separate packages. An operational amplifier is an analog integrated circuit that uses high-gain feedback to amplify the difference between two input voltages. A precision operational amplifier adds requirements for low input offset, low drift, accurate gain behavior, common-mode rejection, and power-supply rejection. The LT1014 belongs to the broader hierarchy of operational amplifier, analog amplifier, analog IC, and semiconductor. Its quad configuration provides four amplifiers while reducing package count, board area, and the number of external power connections compared with four single or dual amplifier packages. The principal LT1014 features are its low 300 uV maximum input offset voltage at 25 °C for the LT1014 grade, 2.5 uV/°C maximum offset-voltage temperature coefficient, 8 million open-loop gain, 117 dB common-mode rejection, and 120 dB power-supply rejection. These characteristics are valuable in bridge and strain-gauge amplifiers, thermocouple conditioning circuits, low-current instrumentation, precision filters, threshold detection, and 4 mA-to-20 mA current-loop transmitters. The low 350 uA supply current supports battery-powered instrumentation where every milliamp can affect operating time. The LT1014 can operate from single 5 V supplies as well as dual ±15 V supplies. Its input range extends to ground and its output can swing toward ground while sinking current, which supports single-supply sensing systems where the signal begins near 0 V. The 14-pin DIP package also supports breadboard prototyping, legacy industrial equipment, and through-hole production assemblies. Typical applications include precision sensor interfaces, low-level current measurement, active analog filters, thermocouple amplifiers, process-control instrumentation, and 4 mA-to-20 mA loop transmitters. The device is most appropriate when low offset and drift are more important than the lower cost or higher drive capability of a general-purpose quad amplifier such as an LM324. Designers should verify input common-mode range, output swing, load current, supply current, stability, and noise bandwidth for the intended configuration. Decoupling capacitors should be placed close to the supply pins, and precision resistor networks should use suitable tolerance and temperature-coefficient grades when gain accuracy matters. This page combines the verified LT1014IN manufacturer information, distributor listing, package details, sourced drop-in family alternatives, and practical engineering guidance to support faster component selection and PCB-level implementation.

견적 요청 문의하기
LT1014MJ - 4-Channel 5V-44V Precision Op Amp | Texas Instruments
LT1014MJ

LT1014MJ - 4-Channel 5V-44V Precision Op Amp | Texas Instruments

The Texas Instruments LT1014MJ is a low-power, four-channel precision operational amplifier with a 5 V to 44 V supply range, dual ±15 V operation, and a 14-pin ceramic DIP package. It supports single 5 V and dual ±15 V supplies, operates across -55°C to +125°C, and provides low offset-voltage temperature coefficient, high gain, low supply current, and low noise. The device contains four amplifiers in an industry-standard 14-pin configuration. A precision operational amplifier is a voltage-gain component that uses negative feedback to amplify small voltage differences while maintaining accuracy, stability, and common-mode performance. The LT1014MJ belongs to the operational-amplifier hierarchy, which includes instrumentation amplifiers, buffer amplifiers, comparators, and general-purpose analog signal-conditioning ICs. Its common-mode input range includes ground, making it useful in systems where signals approach the lower supply rail. The principal benefits are its combination of precision, low noise, low supply current, and wide operating temperature range. Four independent amplifiers in one package reduce board area and simplify instrumentation systems requiring multiple closely related channels. Operation from a single 5 V supply supports portable and industrial equipment, while dual ±15 V operation accommodates higher-amplitude bipolar signals. The ceramic DIP package provides mechanical robustness for industrial, aerospace, and military-qualified systems operating from -55°C to +125°C. Internally, the LT1014MJ is designed around precision bipolar amplifier stages. The low offset-voltage temperature coefficient helps maintain calibration accuracy as ambient temperature changes, while low noise is valuable for resolving small sensor outputs. Its common-mode input range including ground permits direct sensing of low-level signals without a mid-supply reference, although exact offset voltage, input bias current, noise density, gain-bandwidth product, slew rate, and output-swing limits are not supplied in the verified data and must be checked in the manufacturer datasheet. Typical uses include strain-gauge and thermocouple signal conditioning, battery-powered precision instrumentation, 4 mA to 20 mA current-loop transmitters, active filters, gain blocks, and multiple-limit threshold detection. The four-amplifier organization is especially helpful when a system needs differential input stages, output drivers, or multiple filter sections while maintaining consistent device characteristics. When designing around the LT1014MJ, verify the complete input common-mode range, output swing, supply-current behavior, stability requirements, and offset behavior against the selected supply and load. Decoupling should follow the manufacturer guidance, and exposed inputs must be kept within their valid common-mode range. In low-level instrumentation, input bias-current and source-impedance errors may dominate even when the amplifier itself is precise. This product page consolidates verified manufacturer and distributor information, distinguishes the military-temperature 14-pin CDIP ordering code from related LT1014 variants, identifies packaging-specific drop-in candidates, and adds practical selection guidance. It also makes clear where verified pricing or detailed electrical limits were unavailable rather than substituting estimated values.

견적 요청 문의하기