집적 회로

MCP6002-E/P

MCP6002-E/P - Dual 1MHz Low-Power Op Amp | Microchip

Microchip Technology MCP6002-E/P is a dual general-purpose CMOS operational amplifier with rail-to-rail input and output capability, a 1.8 V to 6 V operating supply range, 1 MHz typical gain-bandwidth product, and 100 µA typical quiescent current per amplifier. The device is packaged in an 8-lead PDIP for through-hole PCB assembly. An operational amplifier, or op amp, is an analog signal-conditioning IC that uses high open-loop gain to amplify differences between two input voltages. The MCP6002 belongs to the operational-amplifier hierarchy and is specifically intended for general-purpose voltage amplification, buffering, filtering, and low-frequency signal-processing circuits where low power consumption and rail-to-rail signal handling are valuable. The amplifier's rail-to-rail input stage accepts input voltages across most of the supply range, while its rail-to-rail output stage can approach the positive and negative supply rails under suitable load conditions. This makes the MCP6002 useful in battery-powered equipment, sensor interfaces, and mixed-signal systems operating from 1.8 V to 6 V. Its 1 MHz typical gain-bandwidth product supports modest closed-loop bandwidth requirements rather than high-speed signal processing. Microchip specifies a typical quiescent current of 100 µA and a typical 90° phase margin for the MCP6001, MCP6002, and MCP6004 family. Low quiescent current reduces the standing load imposed by each active channel, which is especially helpful in two-channel designs where both amplifiers may operate continuously. The dual configuration also reduces package count and can simplify board layout compared with two separate single amplifiers. Typical applications include low-frequency sensor conditioning, audio preamplification, voltage buffering, active filtering, joystick or potentiometer interfaces, and portable instrumentation. The 8-lead PDIP package is particularly useful for prototypes, educational equipment, through-hole industrial assemblies, and designs where a socket or hand-soldering is preferred over a fine-pitch surface-mount footprint. Designers should account for input common-mode behavior, output swing, noise, stability with the selected feedback network, and the limits of a 1 MHz amplifier when planning closed-loop gain. Decoupling capacitors should be placed close to the supply pins, and unused inputs should be biased into a valid common-mode range. The DIP outline also requires adequate clearance for through-hole drilling and component spacing. This page combines the manufacturer's device characteristics, documented package choices, equivalent-amplifier guidance, and practical selection criteria. It is intended to help engineers determine whether the MCP6002-E/P's low-power dual-channel architecture and PDIP package fit a specific analog circuit without confusing it with faster, noisier, or more highly integrated alternatives.

견적 요청 문의하기

MCP6002-I/P

MCP6002-I/P - Dual 1MHz R-R Op Amp | Microchip Technology

Microchip Technology MCP6002-I/P is a dual general-purpose operational amplifier with rail-to-rail input and output capability, a 1 MHz typical gain-bandwidth product, and 100 uA typical quiescent current. The device operates from 1.8 V to 6 V and is offered in an 8-lead plastic DIP package. An operational amplifier is an analog signal-conditioning semiconductor that compares an input signal with a feedback-defined reference and amplifies the difference. The dual MCP6002-I/P contains two independent amplifiers in one package, placing it in the hierarchy of operational amplifier, analog amplifier, linear amplifier, signal-conditioning IC, and integrated circuit. Rail-to-rail input and output behavior supports signal operation near the supply rails. The principal features are a 1.8 V minimum operating voltage, a 6 V maximum operating voltage, 1 MHz typical gain-bandwidth product, and 100 uA typical quiescent current. Its 90-degree typical phase margin supports stable operation in conventional closed-loop configurations. The dual amplifier arrangement reduces component count when two independent analog channels are required, while the low-power operating characteristics suit battery-powered and portable equipment. Operationally, the MCP6002-I/P uses its two amplifier sections for independent signal conditioning, buffering, amplification, or feedback-control functions. Rail-to-rail input capability expands the usable input range toward the supply limits, while rail-to-rail output capability allows output voltage to approach those limits under suitable load and frequency conditions. The 1 MHz gain-bandwidth product defines the approximate closed-loop bandwidth available at a given noise-gain setting. Typical applications include low-power sensor conditioning, portable instrumentation, audio input stages, general-purpose voltage buffering, and embedded analog signal processing. Two amplifier sections can handle related channels, such as differential sensor excitation and acquisition or separate signal-conditioning paths. The 8-lead DIP package is particularly useful for prototypes, educational systems, through-hole assemblies, and designs where a socketed or manually assembled implementation is preferred. Designers should verify the signal bandwidth, output swing, input bias current, noise, stability, and load-driving requirements against the operating voltage and load. Place bypass capacitors close to the supply pins, route feedback paths away from noisy input and power nodes, and confirm that the selected gain does not compromise phase margin. The DIP footprint also requires adequate spacing around adjacent board components and consideration of lead-bend radius during manual assembly. This product page combines the manufacturer product information, distributor availability references, and engineering cross-reference results into a focused engineering overview. It also provides package-specific guidance, practical application context, design cautions, and a comparison framework for evaluating drop-in amplifier options without changing the 8-lead DIP footprint.

견적 요청 문의하기

MCP6002-I/SN

MCP6002-I/SN - Dual 1MHz Op Amp, RRIO, 1.8-6V | Microchip

The Microchip Technology MCP6002-I/SN is a dual, general-purpose operational amplifier offering rail-to-rail input and output (RRIO) operation over a 1.8V to 6.0V supply range. Housed in an 8-pin SOIC (SN) package, it provides a typical gain-bandwidth product (GBWP) of 1 MHz, 90-degree phase margin, and a low typical quiescent current of 100 microamperes per amplifier. Industrial temperature range is -40C to +85C. A rail-to-rail operational amplifier is a type of analog IC whose input common-mode range and output swing extend to both supply rails, enabling full utilization of the ADC dynamic range in low-voltage single-supply systems. The MCP6002 sits within the broader product taxonomy of op amp -> amplifier IC -> analog IC -> integrated circuit -> semiconductor. Compared to non-RRIO op amps that lose 1-2V of headroom at each rail, RRIO architectures are the standard choice for battery-powered, sensor-interface, and mixed-signal designs. Key features include a 1 MHz gain-bandwidth product, 0.6 V/microsecond slew rate, 1 pA typical input bias current, and rail-to-rail input/output that allows zero-crossover distortion-free operation near the rails. The device is unity-gain stable, supports capacitive loads up to 200 pF, and includes ESD protection diodes on the inputs. The 8-pin SOIC (SN) package provides a familiar, easy-to-prototype footprint for through-hole-style adapter boards and reflow soldering. Architecturally, the MCP6002 uses a CMOS input stage that achieves 1 pA input bias current - several orders of magnitude lower than bipolar op amps - while the class AB output stage delivers rail-to-rail swing at moderate loads. The combination of low bias current and RRIO makes the part suitable for high-impedance sensor front-ends, photodiode transimpedance amplifiers, and unity-gain buffers driving single-supply ADCs. Typical applications include battery-powered sensor signal conditioning, active filters for audio and instrumentation, transimpedance amplifiers for photodiodes, microcontroller analog input/output buffering, and general-purpose signal amplification in industrial, consumer, and IoT designs. When designing with the MCP6002, observe the input common-mode range includes both rails, but for best distortion performance keep the input 0.3V away from either rail. Decouple the supply pin with a 0.1 microfarad ceramic capacitor placed within 5 mm of the VDD pin, and avoid exceeding 6.0V absolute maximum supply. This page synthesizes distributor pricing from DigiKey, Mouser, and LCSC, drop-in SOIC-8 alternatives including same-family Microchip variants and competitor equivalents, and practical design notes not consolidated on any single manufacturer page.

견적 요청 문의하기

MCP6004-E/P

MCP6004-E/P - 1MHz Quad Low-Power Op Amp | Microchip Technology

The Microchip Technology MCP6004-E/P is a quad general-purpose operational amplifier with rail-to-rail input and output capability, a typical 1 MHz gain-bandwidth product, and a typical 100 uA quiescent current. It operates across a 1.8 V to 6 V supply range and is supplied in a 14-pin PDIP package. The -E/P temperature grade supports an operating range of -40C to +125C. An operational amplifier is an analog signal-conditioning device that compares an input voltage with a feedback reference and amplifies the difference. The MCP6004 contains four amplifiers in one package, allowing a compact circuit to perform buffering, amplification, filtering, sensing, and feedback-control functions. Rail-to-rail input operation allows signals to approach the supply rails, while rail-to-rail output operation helps preserve dynamic range in low-voltage systems. The 1 MHz typical gain-bandwidth product supports general-purpose signal paths rather than high-speed precision applications. The low 100 uA typical quiescent current is useful in battery-operated and portable equipment where standby current affects battery life. The 14-pin PDIP package is also practical for through-hole prototyping, educational platforms, and industrial assemblies where a socket or through-hole layout is preferred. The amplifier family is designed around low-power operation and broad supply compatibility. MCP6004-E/P provides four channels in a single package, reducing the number of components required for multi-channel analog front ends. Its 60 dB minimum common-mode rejection ratio and 4.5 mV input-offset-voltage figure provide useful guidance when designing precision sensor interfaces, although application-level error budgets must account for input bias current, resistor tolerances, noise, and temperature effects. Typical applications include battery-powered sensor conditioning, portable instrumentation, low-voltage audio signal paths, industrial control modules, and general-purpose analog boards. When designing with this device, keep input and feedback networks within the amplifier's common-mode and output-range limits, check stability with the selected load and capacitance, and provide adequate supply bypassing close to the power pins. This product page combines the manufacturer's device information, distributor listings, pin and package references, and engineering-focused design guidance. It helps engineers evaluate the MCP6004-E/P for low-voltage, low-power analog designs before selecting a qualified replacement or planning a new PCB layout.

견적 요청 문의하기

MCP6004-I/P

MCP6004-I/P - Quad 1MHz Low-Power Op Amp | Microchip

The Microchip Technology MCP6004-I/P is a quad general-purpose operational amplifier with rail-to-rail input and rail-to-rail output operation, a 1.8 V to 6 V supply range, a typical gain-bandwidth product of 1 MHz, and a typical quiescent current of 100 µA per amplifier. The device is supplied in a 14-lead PDIP package. An operational amplifier, or op amp, is a high-gain analog signal-processing component that compares two input voltages and amplifies the difference between them. Within the power-management and signal-conditioning hierarchy, the MCP6004 belongs to the general-purpose amplifier class, combining four independent amplifier channels in one integrated circuit. Rail-to-rail input and output capability lets each channel operate close to the supply rails, which is useful in low-voltage systems where the available signal range is limited. Key features include four amplifier channels, a 1.8 V minimum operating supply, a 6 V maximum operating supply, 1 MHz typical gain-bandwidth product, and 100 µA typical quiescent current. The MCP6004-I/P also provides rail-to-rail input and output behavior. These characteristics make it suitable for low-power sensor conditioning, buffering, general analog signal processing, and mixed-signal systems that require multiple amplifier functions without using four separate packages. The 1 MHz gain-bandwidth product supports operation from low-frequency signal conditioning through moderate-bandwidth applications. At unity gain, the usable bandwidth is approximately 1 MHz under typical conditions. Rail-to-rail input capability supports sensing signals near the positive or negative supply limit, while rail-to-rail output allows the amplifier to produce output voltages close to either rail. Actual output swing and stability still depend on load, supply voltage, frequency, and the surrounding circuit. Typical uses include sensor signal conditioning, low-frequency active filtering, voltage buffering, transimpedance stages, instrumentation interfaces, and general-purpose analog gain stages. The four integrated channels can also implement functions such as dual differential amplifiers, comparators with suitable feedback arrangements, or multiple single-ended amplifier stages. Because the MCP6004-I/P operates from 1.8 V to 6 V, it is especially relevant to portable, embedded, industrial-control, and low-voltage instrumentation designs. Designers should verify the required output-current capability, operating temperature grade, noise, offset voltage, and stability under the intended load before finalizing the circuit. Decoupling capacitors should be placed close to the supply pins, and sensitive analog inputs should be kept away from fast-switching nodes. The 14-lead PDIP package also requires adequate spacing between adjacent board-level circuits because its through-hole leads are larger than those of surface-mount packages. This product record combines verified manufacturer and distributor information, exact package identification, purchasing data, application guidance, and an honest review of available drop-in alternatives. It also highlights where additional verification is needed, including the complete pin mapping and alternative qualification, rather than presenting unsupported assumptions as confirmed specifications.

견적 요청 문의하기

MCP601-E/P

MCP601-E/P - 2.8 MHz CMOS Op Amp | Microchip

The Microchip Technology MCP601-E/P is a single, general-purpose CMOS operational amplifier with a 2.8 MHz gain-bandwidth product, 2.3 V/µs slew rate, and 1 pA typical input bias current, supplied in an 8-pin PDIP package. It operates from 2.7 V to 6 V and is specified from -40°C to 125°C, combining low power, rail-to-rail output swing, and low offset voltage. An operational amplifier, or op amp, is an active analog component that compares two input voltages and drives its output toward the higher input. Within the power-management and signal-conditioning hierarchy, an op amp provides gain, buffering, filtering, level shifting, or feedback control. The MCP601-E/P is specifically a single-channel CMOS device intended for low-power precision and general-purpose signal conditioning. The MCP601 family's key specifications include a 2.8 MHz gain-bandwidth product, 2.3 V/µs slew rate, approximately 230 µA typical operating current, and less than 2 mV offset voltage according to the Microchip product page. Its CMOS process supports low bias current, while the rail-to-rail output stage allows the output to approach the supply rails more closely than a conventional output stage. Because the MCP601 is a general-purpose amplifier rather than a power semiconductor, its performance depends mainly on supply voltage, feedback topology, load, output frequency, and circuit stability. The 2.8 MHz bandwidth supports low-frequency instrumentation and signal conditioning, while the 2.3 V/µs slew rate limits large-signal response. Designers should verify noise, offset, bias current, common-mode range, and output-current limits against the manufacturer datasheet for the exact operating conditions. Typical uses include industrial process-control signal conditioning, low-power battery-operated equipment, portable instrumentation, data acquisition, test equipment, and low-end audio circuits. The DIP package is useful for prototyping and through-hole assemblies where a socketed amplifier or easy component replacement is desired. For new production designs, confirm package availability, temperature grade, supply limits, and lifecycle status directly with Microchip or an authorized distributor. The verified product page identifies MCP601 availability across PDIP, SOIC, TSSOP, and SOT-23A packages, but the exact -E/P order code and commercial terms should be checked for the current design. This page combines verified manufacturer specifications, distributor availability information, package details, and application guidance to support faster component selection for low-power analog signal-conditioning designs.

견적 요청 문의하기

MCP601-E/SN

MCP601-E/SN - 2.8 MHz Low-Power RRIO Op Amp | Microchip Technology

The Microchip Technology MCP601-E/SN is a single operational amplifier with a 2.8 MHz gain-bandwidth product, typical operating current of 230 uA, and a maximum input offset voltage below 2 mV, supplied in an 8-lead SOIC package. It is designed for low-power analog signal conditioning using a 2.7 V to 6.0 V single supply. An operational amplifier, or op amp, is an analog building block that uses high open-loop gain to amplify the difference between two input voltages. The MCP601 belongs to the CMOS operational amplifier hierarchy: op amp -> voltage-feedback amplifier -> analog signal-conditioning IC -> semiconductor. Its rail-to-rail output swing allows the output to approach the supply rails more closely than a conventional non-rail-to-rail output stage, which is useful in portable and low-voltage systems. Key features of the MCP601 family include low bias current, high open-loop gain, low typical operating current of 230 uA, and a rail-to-rail output swing. The single MCP601 configuration simplifies designs that require one amplifier, while the 8-lead SOIC package supports conventional surface-mount assembly. The manufacturer identifies the device as suitable for industrial process control, low-power battery-operated equipment, portable equipment, data acquisition, test equipment, and low-end audio applications. The MCP601 uses advanced CMOS technology to provide low bias current and high-speed operation while maintaining low power consumption. Its 2.8 MHz typical gain-bandwidth product supports general-purpose signal amplification rather than high-speed precision applications. The manufacturer datasheet states that the MCP601 operates from a 2.7 V to 6.0 V single supply, although the exact operating temperature and electrical limits for the MCP601-E/SN ordering code should be confirmed against the ordering information in the datasheet. A typical design places input, feedback, and biasing networks around the amplifier, with suitable bypassing close to the supply pins. In battery-powered instrumentation, the 230 uA typical operating current is a meaningful advantage, but the final power budget must include the input bias current, feedback network consumption, and load current. In audio or sensor-signal paths, rail-to-rail output swing can improve available output range, while input common-mode limits and offset voltage remain important selection criteria. The principal design trade-off is bandwidth versus power and precision. A 2.8 MHz amplifier is appropriate for slow analog signals and general-purpose buffering, but it is not the correct choice for wideband video, high-speed instrumentation, or demanding precision applications. Decoupling, layout, input protection, and output-load stability should be reviewed against the manufacturer datasheet before production release. This product summary consolidates the verified manufacturer specifications, distributor availability information, package details, practical application guidance, and explicitly identified drop-in alternatives for engineers evaluating the MCP601-E/SN.

견적 요청 문의하기

MCP601-E/ST

MCP601-E/ST - 2.8MHz RRO Op Amp | Microchip Technology

The Microchip Technology MCP601-E/ST is a single-circuit CMOS operational amplifier with a 2.8 MHz gain-bandwidth product, a 2.3 V/µs slew rate, and rail-to-rail output swing in an 8-TSSOP package. It operates from a 2.7 V to 6 V supply and draws a typical operating current of 230 µA. An operational amplifier is a voltage-gain building block used to amplify small signals, buffer sensors, compare voltages, and implement active analog filters. The MCP601 belongs to the CMOS operational-amplifier family and the broader voltage-amplifier and analog-signal-processing hierarchy. Its rail-to-rail output capability increases the usable output range in low-voltage circuits where conventional fixed-output amplifiers would clip near either supply rail. Key features include a 2.8 MHz gain-bandwidth product, 2.3 V/µs slew rate, typical operating current of 230 µA, and typical offset voltage below 2 mV. The low bias current and high open-loop gain provided by Microchip's advanced CMOS process are useful for battery-powered instrumentation, data-acquisition channels, and sensor interfaces. A single amplifier in the TSSOP package also supports compact analog boards requiring a conventional surface-mount footprint. Technically, the MCP601 combines a low-power CMOS core with general-purpose voltage feedback. Its 2.8 MHz gain-bandwidth product supports operation from low closed-loop gains such as 10 through signal chains requiring moderate bandwidth. The 2.3 V/µs slew rate helps the amplifier reproduce moderate-amplitude step inputs, while the rail-to-rail output reduces headroom loss near the positive or negative supply limit. Exact input common-mode range, noise density, and maximum output swing must be confirmed in the manufacturer datasheet. Typical applications include industrial process-control inputs, portable battery-operated equipment, portable data-acquisition systems, test equipment, and low-end audio products. It is particularly appropriate where low operating current, a small package, and output swing close to the supply rails are more important than the bandwidth and noise of a precision or high-speed amplifier. Designers should verify input common-mode limits, output-load capability, noise, and stability for the intended gain and capacitive load using the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins, while sensitive-input routing should minimize parasitic capacitance and leakage. Because rail-to-rail output does not necessarily guarantee a fully rail-to-rail input range, input-source and input-biasing conditions require separate verification. This page consolidates verified manufacturer and distributor information, package-level alternatives, parameter comparisons, and application guidance. It adds engineering-focused selection criteria and implementation notes that help distinguish a low-power TSSOP operational amplifier from higher-bandwidth, precision, and rail-to-rail-input alternatives.

견적 요청 문의하기

MCP601-I/P

MCP601-I/P - 2.8MHz Low-Power RRIO Op Amp | Microchip

The Microchip Technology MCP601-I/P is a single low-power CMOS operational amplifier with a 2.8 MHz gain-bandwidth product, 230 uA typical quiescent current, and rail-to-rail output swing in an 8-pin PDIP package. According to the manufacturer product page, it operates from a single supply as low as 2.7 V, supports a maximum supply voltage of 5.5 V, and provides less than 2 mV typical offset voltage. An operational amplifier is an analog signal-conditioning integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs while providing high open-loop gain and low output impedance. The MCP601 belongs to the CMOS operational-amplifier hierarchy, combining low bias current, high speed, high open-loop gain, and rail-to-rail output swing in a general-purpose device intended for industrial process control and low-power portable systems. Key characteristics include a 2.8 MHz gain-bandwidth product, 230 uA typical operating current, rail-to-rail output capability, and low input bias current enabled by Microchip's advanced CMOS process. The single-supply operating range of 2.7 V to 5.5 V makes the device suitable for battery-operated equipment, portable instrumentation, and low-voltage industrial control systems. The -I temperature grade identifies the industrial-temperature version. The rail-to-rail output stage allows the output to approach the supply rails under light load, which is useful in single-supply systems where conventional bipolar output stages lose linearity near either rail. Input common-mode range, input offset voltage, slew rate, open-loop gain, input bias current, and noise specifications must be checked against the manufacturer datasheet for the exact operating voltage and configuration. Typical uses include low-power sensor conditioning, process-control loops, data-acquisition front ends, portable test equipment, and low-end audio signal paths. Its 8-pin PDIP format is also convenient for prototyping, educational builds, and through-hole assemblies where a surface-mount package would be inconvenient. Designers should verify stability with the selected feedback network, account for capacitive loading, and provide adequate bypass capacitance near the supply pins. Because the MCP601-I/P is a through-hole industrial-grade variant, engineers changing to a surface-mount production version should confirm pin order, temperature grade, and full electrical equivalence rather than assuming only the family name is equivalent. This page combines manufacturer specifications, distributor sourcing information, package details, application guidance, and honest drop-in replacement analysis that are not consolidated in a single manufacturer product-page summary.

견적 요청 문의하기

MCP601-I/SN

MCP601-I/SN - 2.8 MHz Low-Power Op Amp | Microchip

The Microchip Technology MCP601-I/SN is a single low-power CMOS operational amplifier with a 2.8 MHz gain-bandwidth product, 230 uA typical operating current, and less than 2 mV typical offset voltage. It operates from a single 2.7 V to 5.5 V supply and provides rail-to-rail output swing in an 8-pin SOIC package. The combination of low power, rail-to-rail output, low bias current, and moderate bandwidth makes the MCP601 suitable for portable instrumentation, process-control circuits, sensor interfaces, buffering, and low-end audio systems. An operational amplifier is a voltage-controlled differential amplifier used to amplify, filter, buffer, or compare analog signals. In the signal-chain hierarchy, the MCP601 belongs to the operational-amplifier family, which falls within analog amplifier ICs and broader analog signal-processing systems. Its CMOS implementation supports low input bias current and low static power while maintaining high open-loop gain and rail-to-rail output capability. Key electrical characteristics include a 2.8 MHz gain-bandwidth product, 230 uA typical operating current, an offset voltage below 2 mV, and a 2.7 V to 5.5 V single-supply range. Rail-to-rail output swing allows the amplifier to approach the supply rails under suitable load and output-voltage conditions. The 8-pin SOIC package supports conventional surface-mount assembly and provides separate positive-input, negative-input, output, supply, and ground connections. The advanced CMOS process combines low power consumption with high-speed operation and high open-loop gain. Low input bias current is especially useful when the amplifier is driven by high-impedance sensors or bias networks because it reduces loading-induced errors. The 2.8 MHz gain-bandwidth product is appropriate for general-purpose signal conditioning, audio preamplification, active filtering, and instrumentation rather than high-speed precision applications requiring much wider closed-loop bandwidth. Typical uses include portable sensor interfaces, industrial process-control modules, low-power battery-operated equipment, data-acquisition systems, test equipment, and low-end audio circuits. In a sensor interface, the MCP601 can buffer a high-impedance source before conversion by an ADC. In an active filter, its bandwidth provides useful operating range at moderate signal frequencies. In audio equipment, rail-to-rail output can improve available output swing compared with a fixed-headroom implementation. Design the input network and output load carefully because rail-to-rail output behavior does not eliminate all input common-mode limitations or guarantee maximum swing into every load. Confirm settling time, output-current capability, noise, and stability against the required signal bandwidth. Place the device close to its bypass capacitors and route supply and ground returns to minimize high-frequency impedance and unwanted coupling. This page combines the MCP601-I/SN electrical specifications, manufacturer documentation, application guidance, and verified drop-in replacement information to support faster component selection and PCB-level design decisions.

견적 요청 문의하기

MCP601-I/ST

MCP601-I/ST - 2.7V Rail-to-Rail CMOS Op Amp | Microchip

The Microchip Technology MCP601-I/ST is a single-circuit general-purpose CMOS operational amplifier with rail-to-rail output swing, a 2.7 V minimum supply, and an 8-lead TSSOP package. It operates from a 2.7 V to 5.5 V single supply, making it appropriate for compact, low-voltage analog signal chains. The MCP601-I/ST variant uses the extended industrial temperature grade indicated by its part numbering. A CMOS operational amplifier is an analog building block that uses high input impedance and voltage gain to amplify small signal differences. The MCP601 belongs to the operational-amplifier hierarchy, which connects to analog signal-processing ICs and broader semiconductor systems. Its CMOS construction is intended to support low power consumption, low input bias current, and operation from low-voltage supplies while preserving useful open-loop gain. The manufacturer identifies the MCP601 family as a low-power operational amplifier with rail-to-rail output swing. This output capability is useful when the usable output range must extend close to either supply rail. The family also supports operation with supply voltages as low as 2.7 V and draws less than 325 uA of quiescent current according to the Microchip product page. These characteristics make it useful in battery-operated and portable equipment where every milliamp of supply demand can affect runtime. The MCP601-I/ST uses Microchip's advanced CMOS process technology. Publicly indexed product information describes low bias current, high-speed operation, and high open-loop gain. These properties support sensor conditioning, buffering, and low-level signal amplification, although exact gain-bandwidth, slew-rate, input-bias-current, and offset figures are not included in the supplied verified records and therefore remain marked for data retrieval. Typical uses include portable sensor interfaces, low-voltage instrumentation, audio signal conditioning, and general-purpose analog buffers. In a sensor interface, the amplifier can sit between a high-impedance transducer and a downstream ADC. In a battery-powered circuit, its sub-325 uA quiescent current and 2.7 V minimum operating supply help conserve available energy. Its rail-to-rail output reduces the headroom required when driving a following stage. Designers should verify the complete electrical limits and stability requirements against the manufacturer datasheet before production use. Decoupling capacitors, source impedance, output loading, and the selected gain can affect practical performance. The 8-pin TSSOP footprint is compact, but the exposed thermal limitations and assembly requirements of this small package should be considered alongside ambient temperature and expected dissipation. This page consolidates the verified distributor listing, manufacturer family information, package identification, current pricing reference, and practical selection context. It also distinguishes confirmed drop-in options from package variants that require PCB consideration, helping engineers compare replacements without treating electrically similar parts as automatically interchangeable.

견적 요청 문의하기

MCP602-E/P

MCP602-E/P - 2.8MHz Dual CMOS Op Amp | Microchip

The Microchip Technology MCP602-E/P is a dual general-purpose CMOS operational amplifier with a 2.8 MHz gain-bandwidth product, 2.3 V/us slew rate, and an 8-lead PDIP package. Its typical operating current is 230 uA per amplifier, its typical input offset voltage is below 2 mV, and its specified supply range is 2.7 V to 5.5 V. The device provides rail-to-rail output swing and low bias current, making it suitable for portable, industrial, and signal-conditioning systems. A CMOS operational amplifier is a voltage-controlled differential amplifier implemented with complementary metal-oxide-semiconductor transistors. In the broader electronics hierarchy, an op amp belongs to analog integrated circuits, then amplifiers, then voltage-feedback operational amplifiers, and finally low-power CMOS operational amplifiers. MCP602 combines two independent amplifiers in one package, reducing board area in dual-channel sensor, filtering, buffering, and control circuits. Key features include a 2.8 MHz gain-bandwidth product, 2.3 V/us slew rate, less-than-2 mV typical offset voltage, and 230 uA typical operating current. Rail-to-rail output swing allows the output to approach its supply limits under suitable load conditions, which is useful for low-voltage systems. The dual configuration supports common applications in industrial process control, battery-operated equipment, portable products, data acquisition, test equipment, and low-end audio systems. The MCP602 family is specified for 2.7 V to 5.5 V operation according to the verified manufacturer and distributor material. A separate search result also describes the family as supporting a 2.7 V to 6.0 V single-supply range; because the official product-page result explicitly states 2.7 V to 5.5 V, that verified range is used here. CMOS construction supports low bias current and low power consumption, while the 2.8 MHz bandwidth is adequate for general-purpose low-frequency analog signal conditioning rather than demanding high-speed video or RF stages. Typical applications include two-channel sensor conditioning, portable battery-powered instrumentation, industrial control loops, low-frequency active filters, voltage buffers, audio preamplification, and general data-acquisition front ends. In each case, the designer should verify output swing, input common-mode range, noise, stability, and load drive against the complete operating conditions. The 8-lead PDIP package is suitable for through-hole prototypes, legacy industrial boards, and designs where a dual amplifier in a standard DIP footprint simplifies assembly. For PCB design, place bypass capacitors close to the supply pins and keep analog input and output traces short and away from switching nodes. A common single-supply error is assuming the input common-mode range equals the full rail-to-rail output range; verify the family datasheet for the exact input limits before using the amplifier as a comparator or precision level shifter. This page consolidates verified specifications, sourcing information, design guidance, and explicit data gaps without adding unverified technical claims.

견적 요청 문의하기

MCP602-E/SN

MCP602-E/SN - 2.8 MHz Dual RRO Op Amp | Microchip

The Microchip Technology MCP602-E/SN is a dual general-purpose CMOS operational amplifier with a 2.8 MHz gain-bandwidth product, 230 uA typical operating current per amplifier, and less than 2 mV offset voltage. The device is packaged in an 8-pin SOIC and supports single-supply operation from 2.7 V to 6.0 V. An operational amplifier, or op amp, is a voltage-gain stage used to amplify weak signals, buffer sensors, perform active filtering, compare voltages, and drive analog-to-digital or digital-to-analog converters. The MCP602 belongs to the CMOS operational-amplifier hierarchy, combining low bias current, rail-to-rail output swing, unity-gain stability, and relatively high speed in a low-power analog signal-conditioning IC. The headline features suit compact, low-power analog systems. Its 2.8 MHz gain-bandwidth product supports signal bandwidths well below the unity-gain limit, while the 2.3 V/us typical slew rate provides adequate response for sensor signals and general-purpose instrumentation. Rail-to-rail output swing improves usable output range on low-voltage supplies, and the input range includes ground, allowing operation near the lower supply rail when suitable biasing is applied. Microchip's advanced CMOS process gives the MCP602 low bias current, high open-loop gain, and low typical operating current of 230 uA per amplifier. The dual configuration provides two amplifiers in one 8-pin SOIC, reducing board area compared with two separate single-amplifier packages. Unity-gain stability permits direct voltage-follower use without an external compensation network. Typical uses include industrial process-control loops, portable and battery-operated instruments, data-acquisition front ends, test equipment, and low-end audio signal paths. Each channel can amplify a sensor output, buffer a high-impedance source, implement an active filter, or drive a converter input. The combination of low power and rail-to-rail output is especially useful for systems powered from 3.3 V or 5 V supplies. Designers should verify the input common-mode range, output swing, capacitive-load stability, noise, and output-current capability for the exact operating conditions. Place the bypass capacitor close to the supply pins, use a solid ground reference, and avoid excessive loading on the output. The SOIC outline permits standard surface-mount assembly, but exposed-pad thermal considerations do not apply to this package. This page combines the manufacturer product information with package, pinout, comparison, selection, and practical circuit guidance to help engineers evaluate the MCP602-E/SN without reconstructing the complete design context from separate catalog entries.

견적 요청 문의하기

MCP602-E/ST

MCP602-E/ST - Dual 2.8MHz CMOS Op Amp | Microchip Technology

The Microchip Technology MCP602-E/ST is a dual CMOS operational amplifier with a 2.8 MHz gain-bandwidth product, typical operating current of 230 uA, offset voltage below 2 mV, and rail-to-rail output swing in an 8-lead TSSOP package. The two amplifiers share a common supply and are intended for low-power signal-processing systems that require more than one amplifier per board area. An operational amplifier, or op amp, is a high-gain differential amplifier whose open-loop behavior is controlled by negative feedback. Within the broader semiconductor hierarchy, an op amp is an analog amplifier IC used in signal conditioning, sensing, filtering, buffering, and control systems. Rail-to-rail output swing allows the MCP602 output to approach its supply rails more closely than a conventional output stage, which is useful when the available signal headroom is limited. The MCP602 uses Microchip's advanced CMOS technology to provide low bias current and low power consumption. Its 2.8 MHz gain-bandwidth product is suitable for general-purpose closed-loop signal paths rather than high-frequency precision instrumentation. The typical operating current of 230 uA supports battery-operated equipment, while the offset voltage specification of less than 2 mV provides a useful indication of input-stage matching. The device also provides high open-loop gain and low-bias operation, as stated on the manufacturer product page. The MCP602 family is available in standard PDIP, SOIC, and TSSOP packages, and the MCP602-E/ST ordering code places the dual amplifier in an 8-lead TSSOP. This surface-mount package supports compact layouts in industrial process control, low-power battery-operated devices, portable equipment, data-acquisition systems, test equipment, and low-end audio products. Dual packaging can reduce board area when a circuit requires amplification, buffering, or active filtering in more than one channel. For portable and low-power designs, compare the MCP602's 230 uA typical operating current with the signal accuracy and bandwidth required by the application. Designers should also verify the complete operating-voltage range, electrical limits, input-bias current, noise performance, output-current capability, and temperature limits against the current manufacturer datasheet before releasing production hardware. MCP602-E/ST drop-in alternatives should be evaluated primarily by package and pin compatibility, followed by supply voltage, gain-bandwidth product, input bias current, offset voltage, output swing, and operating current. Exact substitution is not assured when the required specifications differ, even if the amplifier functions appear similar. This page combines the verified manufacturer and distributor information with practical selection, application, and design guidance. The resulting product record is intended to help engineers identify the correct TSSOP footprint, compare available alternatives, and develop an appropriate low-power analog signal path. Manufacturer documentation remains the controlling authority for ratings, test conditions, pin functions, package drawings, and revised production limits.

견적 요청 문의하기

MCP602-I/P

MCP602-I/P - 2.8 MHz Dual CMOS Op Amp | Microchip

Microchip Technology MCP602-I/P is a dual CMOS operational amplifier with a 2.8 MHz gain-bandwidth product, 230 uA typical operating current per amplifier, and less than 2 mV input offset voltage, supplied in an 8-lead PDIP package. The amplifier operates from a single supply of 2.7 V to 6.0 V and supports rail-to-rail output operation with input common-mode range including ground. These characteristics position the MCP602-I/P as a low-power general-purpose amplifier for industrial process control, battery-operated equipment, portable instrumentation, data acquisition, test equipment, and low-end audio systems. An operational amplifier, or op amp, is a high-gain differential amplifier whose feedback network determines the gain of a closed-loop circuit. The MCP602 belongs to the hierarchy CMOS operational amplifier, analog amplifier, signal-conditioning IC, and broader power-management and semiconductor categories. Its two independent amplifier channels allow one package to implement functions such as voltage followers, transimpedance amplifiers, active filters, comparators, and level-shifting stages when supply and input ranges are appropriate. The MCP602-I/P combines several useful low-power characteristics. Its 2.8 MHz gain-bandwidth product provides more bandwidth than typical micropower amplifiers, while the 230 uA typical operating current supports portable and battery-powered designs. Input bias current of 1 pA typical is particularly useful with high-impedance sensors. A unity-gain-stable architecture allows direct voltage-follower use, and the input common-mode range extending to ground simplifies single-supply signal conditioning. The rail-to-rail output improves usable output swing in low-voltage systems. Microchip advanced CMOS technology provides low bias current, high-speed operation, high open-loop gain, and rail-to-rail output swing. The device contains two independent amplifiers rather than one channel, making the 8-lead PDIP suitable for dual-stage analog signal paths. Its minimum operating supply of 2.7 V permits use from regulated 3.3 V systems, while the 6.0 V maximum supports conventional 5 V analog rails within the stated operating range. Typical applications include low-power sensor interfaces, portable measurement systems, industrial process-control circuits, data-acquisition boards, test equipment, and low-end audio amplification or conditioning. In a transimpedance stage, the 1 pA typical input bias current helps limit photocurrent-generated error. In a voltage follower, unity-gain stability and the input range including ground simplify buffering of signals produced by sensors operating near 0 V. Designers should verify signal amplitude, output swing, input common-mode range, noise, and stability under the intended loading before assigning the amplifier to a circuit. The PDIP package is convenient for prototyping, breadboards, and through-hole industrial assemblies, but its lead spacing differs from surface-mount packages. Decoupling and grounding remain important even though the MCP602-I/P is intended for low-power analog systems. This product record combines manufacturer specifications, distributor availability, package information, engineering application guidance, and verified drop-in alternatives. It also distinguishes parameter differences among candidate devices so engineers can select a replacement without mistaking a same-family amplifier for a pin-compatible substitute.

견적 요청 문의하기

MCP602-I/SN

MCP602-I/SN - 2.8MHz Dual CMOS Op Amp | Microchip

Microchip Technology MCP602-I/SN is a dual CMOS operational amplifier with a 2.8 MHz gain-bandwidth product, typical operating current of 230 uA, and offset voltage below 2 mV. It operates from a single 2.7 V to 5.5 V supply and is packaged in an 8-pin SOIC. The MCP602-I/SN provides rail-to-rail output swing and supports input signals extending below ground, making it useful for low-voltage acquisition, filtering, and signal-conditioning circuits. An operational amplifier, or op amp, is a high-gain analog building block used to amplify or buffer a differential input. The MCP602 belongs to the CMOS operational-amplifier family, which combines low bias current, low supply current, and rail-to-rail output capability. Its place in the broader hierarchy is operational amplifier, analog amplifier, voltage-feedback amplifier, and then analog semiconductor. Microchip's advanced CMOS process gives the MCP602 low input bias current, high open-loop gain, 2.8 MHz gain-bandwidth product, and a 2.3 V/us slew rate. Unity-gain stability supports direct use as a buffer. The dual configuration provides two independent amplifiers in one package, reducing board area for balanced filters, sensor interfaces, audio paths, and control loops. Rail-to-rail output swing maximizes usable output range on low-voltage supplies. Typical applications include portable sensor conditioning, low-voltage audio, active filtering, sensor interfaces, industrial instrumentation, and general-purpose embedded signal processing. The 230 uA typical operating current is particularly useful in battery-powered equipment, while the below-ground common-mode input capability helps process signals that approach the negative supply rail. Designers should keep the input common-mode and output swing limits in view, provide adequate supply decoupling, and avoid placing sensitive high-impedance inputs beside noisy switching or digital return paths. The SOIC package also requires attention to thermal performance and copper availability when operating continuously at higher frequencies or driving capacitive loads. This product page combines manufacturer specifications, package and pinout guidance, application-focused design notes, and verified same-footprint alternatives to support faster component selection and PCB planning.

견적 요청 문의하기

MCP602-I/ST

MCP602-I/ST - 2.8 MHz Dual CMOS Op Amp | Microchip

The Microchip Technology MCP602-I/ST is a dual operational amplifier with a 2.8 MHz gain-bandwidth product, typical operating current of 230 uA per amplifier, and input offset voltage below 2 mV, packaged in an 8-pin TSSOP. The MCP602-I/ST provides two independent amplifiers, rail-to-rail output swing, and operation from a single 2.7 V to 5.5 V supply. Its advanced CMOS process supports low bias current, high open-loop gain, and low-power signal conditioning. An operational amplifier, or op amp, is a voltage-controlled differential amplifier whose inverting and non-inverting inputs determine an amplified output. In the broader electronics hierarchy, an op amp belongs to the linear amplifier and analog integrated-circuit families, where it functions as a core building block for sensor interfaces, filters, buffers, comparators, and gain stages. The dual MCP602 integrates two amplifier channels into one package, reducing component count while retaining independent signal paths. The MCP602-I/ST combines a 2.8 MHz typical gain-bandwidth product with a 230 uA typical operating current per amplifier. Its rail-to-rail output allows the output voltage to approach the supply limits, which is useful when the usable signal range must be maximized in low-voltage systems. The input offset voltage is specified below 2 mV, while the device offers a typical CMRR of 90 dB and a typical slew rate of 2.3 V/us. Unity-gain stability supports straightforward voltage-follower and non-inverting amplifier configurations. The device uses advanced CMOS technology to balance speed, low bias current, high open-loop gain, and rail-to-rail output swing. Its 2.7 V minimum supply permits battery-powered operation, and its 5.5 V maximum supply supports conventional 3.3 V and 5 V rails. The dual configuration can be used for two independent amplifier channels, a differential amplifier, an instrumentation-style front end, or a combined filter and buffer. A bypass capacitor close to the supply pins remains essential for stable operation and low-noise performance. Typical applications include low-power sensor signal conditioning, battery-operated instrumentation, audio preamplification, active filtering, and general-purpose dual-amplifier circuits. The MCP602-I/ST is particularly suitable where two low-power amplifier channels are needed without allocating two separate packages. Designers should verify signal bandwidth, output-current requirements, input common-mode range, and stability requirements against the manufacturer datasheet for the selected operating point. The primary design trade-off is speed versus power: the 2.8 MHz gain-bandwidth product is sufficient for many general-purpose analog blocks, but it is not intended for high-frequency video, high-speed instrumentation, or demanding precision applications. Keep input and output routing short, use stable compensation for capacitive loads, and avoid placing the amplifier where its 2.3 V/us typical slew rate limits large-signal settling. This page combines verified manufacturer and distributor information with package-specific pin assignment, design guidance, application analysis, and drop-in replacement screening. It distinguishes verified electrical characteristics from parameters that still require confirmation from the complete manufacturer datasheet, helping engineers make a more defensible low-power analog design decision.

견적 요청 문의하기

MCP6021-E/P

MCP6021-E/P - 10MHz RRIO CMOS Op Amp, 1mA | Microchip

The Microchip Technology MCP6021-E/P is a single, rail-to-rail input and output CMOS operational amplifier with a 10 MHz gain-bandwidth product, a typical operating current of 1.0 mA, and an input offset voltage of less than 0.5 mV, housed in an 8-pin PDIP (0.300 in, 7.62 mm) through-hole package rated for 2.5 V to 5.5 V single-supply operation. An operational amplifier (op amp) is the core active building block of analog and mixed-signal design. It belongs to the amplifier IC hierarchy, sitting below instrumentation amplifiers and above the discrete transistor level, and is used wherever a signal must be amplified, buffered, filtered, or compared against a reference. The MCP6021-E/P is a general-purpose, single-amplifier device, meaning one amplifier per package, and it is the entry point of Microchip's rail-to-rail 10 MHz CMOS family. Key differentiating specifications include a 10 MHz typical gain-bandwidth product, a 7 V/us slew rate, and an input noise density of 8.7 nV/sqrt(Hz) at 10 kHz. Because the output swings rail-to-rail, the device can drive ADC and DAC reference pins, logic-level comparators, and capacitive loads at the extremes of the supply without saturating. The extended-temperature grade keeps the maximum input offset voltage at +/-250 uV, roughly half the +/-500 uV limit of the industrial-grade counterpart, which makes the -E suffix the right choice for precision DC signal chains running from -40 C to +125 C. Technically, the MCP6021 is built on Microchip's advanced CMOS process, which delivers low input bias current, high open-loop gain, and low supply current while still supporting 10 MHz closed-loop operation. Because CMOS inputs present very high impedance, the device sources negligible loading on the preceding stage and pairs naturally with resistive-divider sensor front ends and high-impedance buffers. A single 1.0 uF bypass capacitor on the supply pin is normally sufficient for stable operation at these modest frequencies. Typical applications include low-cost current-sense and voltage-sense amplifier front ends, sensor signal conditioning for thermistors, strain gauges and photodiode amplifiers, active low-pass filters in audio and telemetry chains, and rail-to-rail logic-level comparators for battery-powered monitoring equipment. When designing around this part, note that the small-signal bandwidth is 10 MHz while the full-power bandwidth is set by the 7 V/us slew rate; for large-signal, high-amplitude stages a wider-bandwidth amplifier may be preferable. The PDIP package also gives a generous thermal path for prototyping and low-volume builds where an SOT-23-5 or SOIC-8 variant would be mechanically inconvenient. This page consolidates distributor pricing, verified electrical characteristics, drop-in pin-compatible alternatives, and practical layout notes that are not gathered together in the original manufacturer datasheet, giving engineers a single decision-ready reference for the MCP6021-E/P.

견적 요청 문의하기

MCP6021-I/P

MCP6021-I/P - 10MHz R-R I/O Op Amp | Microchip

The Microchip Technology MCP6021-I/P is a single-rail-to-rail input and output operational amplifier with a 10 MHz typical gain-bandwidth product, 8.7 nV/√Hz typical input noise at 10 kHz, and a 7 V/μs typical slew rate, packaged in an 8-pin PDIP. Its typical operating current is 1.0 mA, while its typical offset voltage is below 0.5 mV. The MCP6021-I/P combines these attributes with low distortion of 0.00053% THD+N, making it suitable for general-purpose signal conditioning, instrumentation, audio, industrial control, and low-power embedded systems. An operational amplifier is a voltage-feedback amplifier used to amplify, buffer, filter, or compare analog signals. In the electronics hierarchy, the MCP6021-I/P is a general-purpose amplifier IC, a single-circuit CMOS operational amplifier, and a member of the broader analog signal-processing and power-management ecosystem. Rail-to-rail input and output operation allows useful signal range near the supply rails, while the single-channel 8-pin PDIP package supports through-hole industrial and educational assemblies. Key features include a 10 MHz typical gain-bandwidth product for moderate-frequency signal processing, an 8.7 nV/√Hz typical noise density at 10 kHz, and low typical operating current of 1.0 mA. The manufacturer datasheet identifies rail-to-rail input and output behavior as a central feature. The industrial-temperature ordering option provides a maximum input offset voltage of ±500 μV, according to the supplied manufacturer-page information. The MCP6021 family uses advanced CMOS technology to provide low bias current, high-speed operation, high open-loop gain, and rail-to-rail output swing. These characteristics make the device practical for sensor buffers, low-level signal conditioning, active filtering, and general signal amplification where low quiescent current and broad input range are more important than high precision in a very wide bandwidth. The single-amplifier configuration also avoids the extra channel and dual-amplifier complexity of the MCP6022 and MCP6024 devices. Typical applications include portable instrumentation, sensor interfaces, audio preamplification, industrial data acquisition, control loops, and battery-powered monitoring equipment. The 8-pin PDIP format is especially useful for prototypes and designs that favor inspectable through-hole construction. The manufacturer product page specifically identifies 10 MHz gain-bandwidth product, 1.0 mA typical operating current, and offset voltage below 0.5 mV as defining characteristics. Designers should verify the exact supply-voltage range, input common-mode limits, output-load capability, and stability requirements against the manufacturer datasheet before implementation. Decoupling capacitors should be placed close to the supply pins, and the unused amplifier channel should be configured according to the datasheet recommendations rather than left floating. This page combines verified manufacturer and distributor data with application guidance, package details, and strict drop-in alternative analysis. It also distinguishes genuine 8-pin PDIP alternatives from SOIC and dual-amplifier parts that may be functionally similar but are not pin-to-pin drop-in replacements.

견적 요청 문의하기

MCP6022-E/P

MCP6022-E/P - Dual 10 MHz Rail-to-Rail Op Amp | Microchip

The Microchip Technology MCP6022-E/P is a dual operational amplifier with a 10 MHz gain-bandwidth product, rail-to-rail input and output operation, and a typical operating current of 1.0 mA per amplifier. The device is supplied in an 8-lead PDIP package and is specified for operation from 2.5 V to 5.5 V, making it suitable for low-voltage analog signal-processing systems. Its input offset voltage is specified as less than 0.5 mV, while the manufacturer identifies the MCP6022 family as using advanced CMOS technology for low power consumption and low noise. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The MCP6022 contains two amplifier channels in one package, providing a compact solution for filtering, buffering, gain stages, instrumentation, and general-purpose signal conditioning. In the broader power-management hierarchy, the device belongs to the amplifier IC class and is used to condition signals generated by sensors, converters, data-acquisition circuits, and communication equipment. The MCP6022 family provides rail-to-rail input and output operation, which helps maximize usable signal range in single-supply designs. Its 10 MHz gain-bandwidth product supports moderate-speed amplification, and the reported 8.7 nV/√Hz input-noise density is useful for low-noise signal conditioning. The device also has low distortion, with the family documentation reporting 0.00053% THD+N. The dual configuration reduces board area by integrating two amplifier channels into one package. Typical applications include sensor signal conditioning, low-voltage audio and communication interfaces, active filters, data converters, portable instrumentation, and industrial control modules. The 2.5 V minimum supply operation is beneficial for battery-powered and embedded systems, where the amplifier must operate directly from a low-voltage rail. When designing a board around the MCP6022-E/P, check the required input common-mode range, output swing, load drive, stability, and noise performance against the application. Decoupling capacitors should be placed close to the supply pins, and sensitive analog inputs should be routed away from switching nodes and high-current return paths. This product page consolidates verified manufacturer and distributor information, package information, pricing placeholders where verified pricing is unavailable, and engineering-focused selection guidance for the MCP6022-E/P.

견적 요청 문의하기

MCP6022-I/P

MCP6022-I/P - Dual 10MHz RRIO Op Amp | Microchip

The Microchip Technology MCP6022-I/P is a dual, rail-to-rail input/output CMOS operational amplifier with a 10 MHz gain-bandwidth product, typical operating current of 1.0 mA, and input offset voltage below 0.5 mV, housed in an 8-pin dual-inline package. The two amplifiers can operate from a single supply, making the device suitable for compact analog signal-conditioning designs that require rail-to-rail input and output behavior. An operational amplifier is an active analog building block that compares two input voltages and drives its output toward the higher input voltage. The MCP6022 belongs to the operational-amplifier hierarchy within amplifier ICs and analog signal processing. Its rail-to-rail input characteristic accepts signals close to the supply rails, while rail-to-rail output improves dynamic range in low-voltage systems where conventional bipolar amplifiers cannot approach the output limits. The MCP6022-I/P provides 10 MHz gain-bandwidth product, 8.7 nV/√Hz input noise, less than 0.5 mV typical input offset voltage, and 0.00053% THD+N. Its typical operating current is only 1.0 mA per amplifier. These characteristics balance bandwidth, low-noise performance, output fidelity, and power consumption for cost-sensitive applications rather than serving as an ultra-low-power or precision-only amplifier. Microchip's advanced CMOS process supports low bias current, high-speed operation, high open-loop gain, and rail-to-rail output swing. A practical dual amplifier can implement two independent gain stages, buffers, filters, or comparator-style threshold circuits. Because the device operates from a single supply, system designers should establish a mid-supply virtual ground when the signal must be biased around 0 V, or use bipolar supplies when the signal path permits. Typical applications include low-level sensor conditioning, audio preamplification, active filtering, voltage buffering, portable instrumentation, and mixed-signal interface circuits. The 10 MHz bandwidth is well suited to moderate-frequency signal paths, while the 1.0 mA typical operating current supports low-power designs when system activity is intermittent. Design around the input common-mode range, output swing, stability, and supply bypass requirements listed in the manufacturer datasheet. Place the supply-decoupling capacitor close to the positive and negative pins, keep feedback routing short, and verify stability with the intended source impedance, load capacitance, and gain network. This product page combines the manufacturer specifications, package details, practical application guidance, and verified drop-in replacement information to support faster component selection and board-level implementation.

견적 요청 문의하기

MCP6023-E/P

MCP6023-E/P - 10 MHz Rail-to-Rail Op Amp | Microchip Technology

The Microchip Technology MCP6023-E/P is a single-circuit, rail-to-rail input and output operational amplifier with a 10 MHz gain-bandwidth product, typically 1.0 mA operating current, and offset voltage below 0.5 mV, supplied in an 8-pin PDIP package. It uses Microchip's advanced CMOS technology to provide low bias current, high open-loop gain, rail-to-rail output swing, and low-power operation for portable and industrial signal-processing systems. An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages. The MCP6023 belongs to the CMOS operational-amplifier family and is designed for general-purpose signal conditioning, where low power consumption, wide common-mode input range, and output swing close to the supply rails are useful. Its rail-to-rail input and output characteristics make it suitable for battery-powered equipment where useful signal range is limited by the available supply voltage. The 10 MHz gain-bandwidth product supports signal amplification at moderate frequencies, while the approximately 1.0 mA typical operating current helps reduce battery consumption in portable applications. The specified offset voltage below 0.5 mV supports accurate low-level signal handling, and CMOS operation provides low bias current for high-impedance source applications. Microchip identifies the MCP6023 as suitable for industrial process control, data acquisition, test equipment, and low-end audio applications. The MCP6023-E/P is available in an 8-pin PDIP package and is the extended-temperature ordering option identified by the -E suffix in the verified distributor data. Designers should confirm the complete electrical limits, recommended operating conditions, pin assignments, and application-specific performance against the manufacturer datasheet before production release. Typical uses include battery and loop-powered instrumentation, low-power sensor interfaces, portable measurement equipment, industrial process-control circuits, and low-end audio signal paths. The wide common-mode input behavior and output swing allow useful operation close to the supply rails, while the low operating current is valuable where every milliamp affects battery life. The amplifier should be configured with suitable bypass capacitance and stable feedback compensation according to the manufacturer guidance. This product summary combines the verified manufacturer and distributor information with practical selection guidance, package details, application context, and design considerations. It also distinguishes the confirmed PDIP ordering option from other MCP6023 package and temperature variants so engineers can verify footprint, qualification, and sourcing requirements before substituting a part.

견적 요청 문의하기

MCP6023-I/P

MCP6023-I/P - 10 MHz Rail-to-Rail Op Amp | Microchip Technology

The Microchip Technology MCP6023-I/P is a single general-purpose CMOS operational amplifier with a 10 MHz gain-bandwidth product, rail-to-rail input and output swing, and a 2.5 V minimum supply requirement. It is packaged in an 8-pin PDIP and is specified for industrial temperature operation. The device also provides a shutdown or chip-select function according to the Microchip MCP6023 product family information. The MCP6023 belongs to the operational-amplifier hierarchy: it is a general-purpose amplifier, a voltage-feedback signal-conditioning amplifier, and ultimately a semiconductor active device. Rail-to-rail input operation allows the amplifier to sense signals close to either supply rail, while rail-to-rail output swing improves usable output range in low-voltage systems. These characteristics are useful when the signal source operates from a 3.3 V or 5 V rail and the available signal headroom is limited. The MCP6023-I/P combines a typical operating current of 1.0 mA with a typical gain-bandwidth product of 10 MHz. Its typical slew rate is 7 V/us, and its voltage-noise density is 8.7 nV/Hz at 10 kHz. The manufacturer describes a typical input offset voltage below 0.5 mV, with the industrial-grade -I/P version providing a maximum offset voltage of 500 uV according to distributor specification data. These figures make it suitable for general signal conditioning rather than precision instrumentation applications requiring very low offset or drift. Typical uses include low-voltage sensor interfaces, audio preamplifier stages, active filters, ADC driver blocks, and general-purpose buffering. Because the output can approach the supply rails, the device is also useful in mixed-signal systems where a conventional amplifier would clip before the system ADC or downstream converter reaches its usable range. The shutdown feature can also reduce supply consumption when the signal chain does not need to remain active. When designing around the MCP6023-I/P, verify the datasheet pinout and the shutdown-pin logic before layout. Because this is a bipolar-package device intended for through-hole assembly, confirm available PCB footprint, insertion tooling, and connector clearance. Decoupling capacitors should be placed close to the supply pins, and the amplifier should be configured with stable feedback values for the intended gain and load. This page combines manufacturer and distributor specifications, package information, sourcing links, application guidance, and replacement considerations. It is intended to help engineers confirm electrical suitability, package compatibility, and lifecycle availability before placing the MCP6023-I/P into a production bill of materials.

견적 요청 문의하기

MCP6024-E/P

MCP6024-E/P - Quad 10 MHz RRIO Op Amp | Microchip

The Microchip Technology MCP6024-E/P is a quad general-purpose operational amplifier with a 10 MHz gain-bandwidth product, 1.0 mA typical operating current, and less than 0.5 mV input offset voltage, supplied in a 14-pin DIP package. The four amplifiers in this package support single-supply operation from 2.5 V and feature rail-to-rail input and output stages. An operational amplifier, or op amp, is a high-gain analog building block that compares two input voltages and drives its output toward the higher voltage. The MCP6024 belongs to the linear-amplifier and signal-conditioning hierarchy, where precision amplification, filtering, buffering, and sensing are combined within one IC. Its quad configuration reduces package count when a design needs four amplifiers, while rail-to-rail input and output behavior increases usable signal range near the supply rails. The 10 MHz gain-bandwidth product supports higher closed-loop bandwidth than a low-frequency precision amplifier, making the device suitable for audio, communication, and general analog signal paths. Input noise is specified at 8.7 nV/√Hz, while typical operating current is 1.0 mA and the stated input offset voltage is below 0.5 mV. These specifications support low-power designs that still require adequate bandwidth and low-noise behavior. The MCP6024-E/P uses Microchip advanced CMOS technology to provide low bias current, high open-loop gain, high-speed operation, and a high-output-swing rail-to-rail stage. Its 7 V/µs slew rate gives the amplifiers useful large-signal response for moderate-frequency waveforms. Distortion is specified at 0.00053% THD+N, which is relevant when preserving low-level analog signals through gain and filtering stages. Typical uses include low-level sensor conditioning, active filtering, audio signal amplification, communications interfaces, data acquisition, and general-purpose buffering. The quad package is particularly useful when four similar channels are required, such as multiple sensor inputs, gain stages around transducers, or signal-conditioning sections around a converter. When designing around the MCP6024-E/P, verify the required output swing, input common-mode range, noise, and stability for the selected gain at the actual supply voltage. Decoupling capacitors should be placed close to the supply pins, and sensitive high-impedance inputs require careful board layout to minimize leakage, coupling, and input-bias-current errors. This page consolidates the verified manufacturer specifications, distributor pricing, same-package replacement options, and application-oriented design guidance. It also distinguishes confirmed drop-in candidates from broader functional equivalents so engineers can make package, temperature-grade, and parameter checks before approving a substitution.

견적 요청 문의하기

하위 카테고리

제품 (39,000+)

MCP6002-E/P - Dual 1MHz Low-Power Op Amp | Microchip

MCP6002-I/P - Dual 1MHz R-R Op Amp | Microchip Technology

MCP6002-I/SN - Dual 1MHz Op Amp, RRIO, 1.8-6V | Microchip

MCP6004-E/P - 1MHz Quad Low-Power Op Amp | Microchip Technology

MCP6004-I/P - Quad 1MHz Low-Power Op Amp | Microchip

MCP601-E/P - 2.8 MHz CMOS Op Amp | Microchip

MCP601-E/SN - 2.8 MHz Low-Power RRIO Op Amp | Microchip Technology

MCP601-E/ST - 2.8MHz RRO Op Amp | Microchip Technology

MCP601-I/P - 2.8MHz Low-Power RRIO Op Amp | Microchip

MCP601-I/SN - 2.8 MHz Low-Power Op Amp | Microchip

MCP601-I/ST - 2.7V Rail-to-Rail CMOS Op Amp | Microchip

MCP602-E/P - 2.8MHz Dual CMOS Op Amp | Microchip

MCP602-E/SN - 2.8 MHz Dual RRO Op Amp | Microchip

MCP602-E/ST - Dual 2.8MHz CMOS Op Amp | Microchip Technology

MCP602-I/P - 2.8 MHz Dual CMOS Op Amp | Microchip

MCP602-I/SN - 2.8MHz Dual CMOS Op Amp | Microchip

MCP602-I/ST - 2.8 MHz Dual CMOS Op Amp | Microchip

MCP6021-E/P - 10MHz RRIO CMOS Op Amp, 1mA | Microchip

MCP6021-I/P - 10MHz R-R I/O Op Amp | Microchip

MCP6022-E/P - Dual 10 MHz Rail-to-Rail Op Amp | Microchip

MCP6022-I/P - Dual 10MHz RRIO Op Amp | Microchip

MCP6023-E/P - 10 MHz Rail-to-Rail Op Amp | Microchip Technology

MCP6023-I/P - 10 MHz Rail-to-Rail Op Amp | Microchip Technology

MCP6024-E/P - Quad 10 MHz RRIO Op Amp | Microchip