집적 회로

PIC12LF1501-I/SN

PIC12LF1501-I/SN - 8-bit 20MHz 1.75KB Flash MCU | Microchip

The Microchip Technology PIC12LF1501-I/SN is an 8-bit PIC® 12F-series RISC microcontroller with 1.75KB (1K x 14) of Flash program memory, 64 bytes of SRAM, and a 4-channel 10-bit ADC. It operates up to 20MHz from a 2.5V to 3.6V supply in an 8-pin SOIC (SN) package, with 6 I/O lines sharing the standard PIC12 pinout. An 8-bit microcontroller (MCU) is a small computer-on-a-chip built around an 8-bit data path and integrated peripherals such as Flash, RAM, ADC, timers, and configurable logic cells. Within Microchip's taxonomy, the PIC12LF1501 belongs to the PIC12F family -> 8-bit PIC microcontrollers -> microcontrollers (MCU) -> embedded microcontrollers -> semiconductors. The 'LF' suffix denotes a low-voltage (2.5V-3.6V) variant aimed at battery-powered designs that sit below the standard PIC12F 5V operation. Key features include Microchip's eXtreme Low Power (XLP) technology with sub-µA sleep currents, three 8-bit timers (TMR0/TMR2 with postscaler/TMR4 or TMR6), a Configurable Logic Cell (CLC), a Numerically Controlled Oscillator (NCO), 4-channel 10-bit ADC, and an on-board 4xPLL that allows 20MHz operation from an internal 5MHz HFINTOSC. The device also offers two comparators and an enhanced PWM with up to 4 outputs, providing significant analog and digital integration for its 8-pin footprint. The PIC12LF1501 uses a Harvard RISC core with a single-cycle instruction architecture (apart from branches), enabling predictable 20MHz throughput (~5 MIPS). The internal oscillator, PLL, and ADC enable BOM reduction by removing the external crystal, while the CLC and NCO blocks add hardware glue logic without extra ICs. The SOIC-8 package simplifies hand prototyping and reflow assembly on small boards. Typical applications include battery-powered IoT sensor nodes, wearable devices, general-purpose LED lighting controllers, low-power remote controls, and small consumer appliances where 8 pins are sufficient. Designers pick this part when they need more analog integration (CLC, NCO, ADC) than the PIC12F675/683 while retaining the same SOIC-8 footprint and pinout. When designing, ensure VDD decoupling is placed close to pin 1 and pin 8, and that the ICSPDAT/ICSPCLK pins remain accessible for in-circuit serial programming. Note the -I (industrial) temperature grade covers -40°C to +85°C, so the -E grade is required for -40°C to +125°C automotive/industrial-thermal designs. This page synthesizes verified distributor pricing, drop-in same-package alternatives, application notes, and design notes not consolidated on a single manufacturer page, accelerating sourcing and design-in decisions for the PIC12LF1501-I/SN.

견적 요청 문의하기

PIC12LF1501T-I/MC

PIC12LF1501T-I/MC - 8-bit MCU, 1.75KB Flash, 20MHz, 8-DFN | Microchip

The Microchip Technology PIC12LF1501T-I/MC is an 8-bit PIC12 family RISC microcontroller featuring 1.75KB (1K x 14) of Flash program memory, 64 bytes of RAM, and a 10-bit ADC, housed in an 8-pin DFN (2x3 mm) package. It operates from a 2.5V to 3.3V supply and supports instruction execution at up to 20MHz via an internal oscillator, making it well suited for compact, low-pin-count embedded designs. An 8-bit PIC microcontroller is a small, low-cost, low-power CMOS processor built around Microchip's Harvard RISC architecture. It belongs to the PIC12 sub-family, the smallest-pin-count branch of the PIC10/12/16/18 hierarchy, and falls under the broader microcontroller -> embedded controller -> semiconductor taxonomy. PIC12LF variants specifically use the 'LF' process node for low-voltage operation between 1.8V and 3.6V, distinguishing them from 'F' variants that target 2.3V to 5.5V. The 'T' suffix indicates Tape & Reel packaging, while 'I/MC' denotes the industrial temperature grade (-40C to +85C) in the DFN-8 (MC) package. Key features of the PIC12LF1501T-I/MC include 6 I/O pins, four 10-bit ADC channels, one comparator, a Configurable Logic Cell (CLC), a Complementary Waveform Generator (CWG), and a Numerically Controlled Oscillator (NCO). The device also supports eXtreme Low Power (XLP) sleep currents below 20 nA, making it competitive against larger MCUs in energy-harvesting and battery-backed applications. Architecturally, the PIC12LF1501 uses a 14-bit instruction word and a two-stage pipeline, delivering deterministic interrupt latency typical of the PIC family. The 10-bit ADC uses a Successive Approximation Register (SAR) architecture with acquisition control, while the CWG module provides dead-band control for half-bridge MOSFET drive. Internal oscillator calibration is factory-trimmed to within +/-1% typical. Typical applications include IoT sensor nodes, wearable health bands, low-end remote controls, LED lighting controllers, and battery-powered consumer accessories. The 6 I/O and small footprint also serve well in disposable medical devices and disposable industrial tags. When designing with this part, ensure decoupling of VDD with a 100 nF ceramic capacitor placed within 3 mm of the pin, and configure unused I/O as outputs low to minimize current draw. Programming is supported via MPLAB X IDE, PICkit 3/4, and ICD 3/4. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

견적 요청 문의하기

PIC12LF1501T-I/MS

PIC12LF1501T-I/MS - 8-Bit MCU, 1.75KB Flash, 20MHz, MSOP-8 | Microchip

The Microchip PIC12LF1501T-I/MS is an 8-bit RISC microcontroller based on the enhanced PIC12 mid-range core, integrating 1.75KB (1K x 14 words) of self-programmable Flash program memory and 64 bytes of SRAM in an 8-pin MSOP package. The device operates at up to 20 MHz instruction frequency from a 2.5 V to 3.6 V supply, with six general-purpose I/O pins, one 10-bit ADC with up to 4 input channels, two 8-bit timers plus one 16-bit timer, and on-chip peripherals including Configurable Logic Cells (CLC), a Numerically Controlled Oscillator (NCO), and enhanced PWM. The LF prefix denotes the low-voltage variant of the PIC12F1501 family. A PIC12 microcontroller is a member of the 8-bit microcontroller family, which sits in the broader taxonomy of embedded microcontrollers -> microcontrollers -> microprocessors and controllers -> semiconductors. PIC12 devices use a Harvard-architecture RISC instruction set with a fixed 14-bit instruction width, making them well suited for cost- and power-sensitive embedded applications that require deterministic interrupt latency and small code footprint. The PIC12LF1501 specifically belongs to the PIC12F1501 low-pin-count sub-family designed for compact analog and sensor-interface designs. Key features include 1.75KB Flash with self-programmability, 64 bytes SRAM, 6 I/O pins, a 10-bit ADC with 4 channels, two 8-bit timers, one 16-bit timer, enhanced PWM, CLC, NCO, and a power-saving Sleep mode drawing microamp-level current. The internal 16 MHz high-speed oscillator and 32 kHz low-power oscillator allow flexible clocking without external crystals. Architecturally the device uses a 14-bit instruction word, 8-level hardware stack, and single-cycle ALU operations, giving an effective throughput approaching 5 MIPS at 20 MHz. The 10-bit ADC is implemented with a successive-approximation register (SAR) topology, and the CLC blocks allow combinatorial logic to be implemented on-chip, reducing external gates. On-chip debug is supported via the ICSP two-wire interface. Typical applications include IoT sensor nodes, battery-powered remote controls, low-cost LED controllers, capacitive-touch user interfaces, small appliances, smart wearables, and consumer toys. Its low Sleep current makes it attractive for energy-harvesting designs and always-on interrupt-driven systems. When designing with this part, ensure VDD decoupling uses a 100 nF ceramic capacitor placed within 2 mm of the VDD pin, keep analog signal traces short, and connect unused I/O pins to defined logic levels to minimize ICC leakage. This page synthesizes distributor pricing, drop-in same-package alternatives from Microchip, and practical design notes not found in the standalone manufacturer datasheet, giving procurement and design engineers a single reference for evaluation and sourcing.

견적 요청 문의하기

PIC12LF1501T-I/SN

PIC12LF1501T-I/SN - 8-Bit MCU 1.75KB Flash 20MHz | Microchip

The Microchip Technology PIC12LF1501T-I/SN is an 8-bit PIC microcontroller from the PIC® 12F family featuring 1.75KB (1K x 14) of Flash program memory, 64 bytes of RAM, and 6 I/O pins in a compact 8-pin SOIC (SN) package. It operates at up to 20MHz instruction clock from a 2.5V to 3.6V supply and integrates a 10-bit ADC, Configurable Logic Cell (CLC), Numerically Controlled Oscillator (NCO), Complementary Waveform Generator (CWG), and Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART). An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path that fetches, decodes, and executes instructions stored in non-volatile program memory. In the broader taxonomy, an 8-bit MCU belongs to the microcontroller family, which sits within embedded processors, which in turn are a class of semiconductors used in power-managed digital control. The PIC® architecture uses a Harvard RISC core with single-cycle instructions, providing deterministic timing for real-time control loops. Key features include a 20MHz internal oscillator, 10-bit ADC with up to 4 channels, 4 PWM outputs via the CWG, brown-out reset (BOR), power-on reset (POR), watchdog timer (WDT), and In-Circuit Serial Programming (ICSP) via two pins. The CLC and NCO peripherals allow digital logic and frequency synthesis without external components, reducing BOM cost. The wide 2.5V-3.6V operating range supports both 3.3V regulated supplies and direct 2x AA/AAA battery operation. Technical depth: the device is built on Microchip's enhanced mid-range 8-bit core with 200ns instruction execution, 16-level hardware stack, and 33 single-word instructions. Internal peripherals share an interrupt controller with vectored priority, allowing deterministic response to ADC, timer, CLC, and EUSART events. The 'LF' prefix designates the low-voltage F-series variant optimized for low-power 3.3V operation. Typical applications include battery-powered sensor nodes, LED lighting controllers, consumer appliances, low-cost motor control, and general-purpose logic replacement. The 6 I/O pins are sufficient for blink, fade, sense, and communicate designs, while the ADC enables direct interface with thermistors, potentiometers, and analog sensors. Design consideration: at 20MHz and 3.3V, core current is typically a few mA active; for battery applications, use SLEEP mode between ADC samples to drop current to sub-microamp levels and extend coin-cell life. The 'T' suffix denotes tape-and-reel packaging; pinout is identical to the non-T variant. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical low-power design notes not found in the manufacturer datasheet alone, making it easier to select and source the PIC12LF1501T-I/SN for production.

견적 요청 문의하기

PIC12LF1552-E/MS

PIC12LF1552-E/MS - 8-bit MCU, 3.5KB Flash, MSOP-8 | Microchip

The Microchip Technology PIC12LF1552-E/MS is an 8-bit flash microcontroller in the PIC12LF family, featuring 3.5KB of program Flash memory, 256 bytes of RAM, and a 32 MHz internal oscillator in an 8-pin MSOP package. It is one of the smallest and lowest-cost PIC MCUs with hardware I2C/SMI support, designed for space-constrained and cost-sensitive embedded applications. What is a PIC microcontroller? A PIC (Peripheral Interface Controller) is a family of 8-bit, 16-bit, and 32-bit microcontrollers made by Microchip Technology, built on a Harvard RISC architecture with separate program and data buses. PIC MCUs integrate a CPU, Flash program memory, RAM, peripherals (ADC, timers, communication interfaces), and I/O into a single IC, forming the embedded "brain" of countless consumer, industrial, and automotive products. Within that taxonomy, the PIC12F subfamily targets the smallest 6-, 8-, and 14-pin packages, optimized for cost-sensitive and compact designs where every square millimeter of PCB matters. Key features of the PIC12LF1552 include a 4-channel 10-bit ADC, advanced Capacitive Voltage Divider (CVD) controls for mTouch capacitive sensing, a programmable voltage reference, hardware MI2C/SPI peripherals, 25 mA source/sink I/O for direct LED drive, an internal 32 MHz oscillator, Low-Power Brown-Out Reset (LPBOR), and an extended Watchdog Timer. The "LF" suffix indicates the wide 1.8V to 3.6V operating range, allowing direct battery connection for single-cell Li-ion or two-AA designs. Architecturally, the device uses a 14-bit instruction word with a two-stage pipeline, achieving throughput of 8 MIPS at 32 MHz. On-chip peripherals include the CVD front-end for mTouch proximity and button sensing, programmable reference for ADC calibration, and configurable digital I/O with weak pull-ups. Typical applications include mTouch capacitive touch buttons, low-cost IoT sensor nodes, consumer remote controls, LED lighting strips, wearable fitness accessories, battery-powered toys, and small appliance user interfaces. In all of these, the device's tiny MSOP-8 footprint combined with its integrated peripherals eliminates the need for external ADC, touch controller, or LDO components. A key design consideration when using the PIC12LF1552 is oscillator accuracy: the internal 32 MHz HFINTOSC has a typical accuracy of approximately +/-1% over voltage and temperature, so designs requiring USB, UART at high baud, or RF timing should use a calibrated oscillator mode or external crystal. The CVD module also requires firmware tuning to compensate for board parasitic capacitance and temperature drift. This page synthesizes distributor pricing, drop-in alternative MSOP-8 PIC12LF/12F/16F family parts, and practical design notes not found in the manufacturer datasheet alone.

견적 요청 문의하기

PIC12LF1552-E/P

PIC12LF1552-E/P - 8-bit MCU 32MHz 3.5KB Flash | Microchip

The Microchip Technology PIC12LF1552-E/P is an 8-bit PIC® 12F-family microcontroller running up to 32MHz internal oscillator with 3.5KB (2K x 14) Flash program memory, 256 bytes RAM, and a hardware I2C peripheral, housed in an 8-pin PDIP through-hole package. It targets cost- and space-constrained embedded designs that still need a true hardware I2C/SMBus master and capacitive-touch (mTouch) sensing channels. An 8-bit microcontroller (MCU) is a small programmable computer on a single chip combining a CPU, RAM, Flash program memory, and peripherals such as ADC, timers, and communication blocks. PIC microcontrollers are widely used in consumer, industrial, and automotive applications for deterministic control loops. The PIC12LF1552 sits inside the PIC® 12F family -> 8-bit PIC® family -> microcontrollers -> integrated circuits -> semiconductor device hierarchy. Key features include 32MHz internal oscillator, 6 I/O pins, 10-bit ADC with up to 4 channels, 2 timers, hardware I2C/SMBus master, mTouch capacitive-touch sensing peripheral, and 1.8V-3.6V wide operating voltage. The integrated mTouch peripheral enables proximity and button-touch sensing without external RC components, reducing BOM and PCB area for HMI designs. The PIC12LF1552 uses a RISC architecture with 49 instructions and a 14-bit instruction word, providing deterministic instruction timing ideal for real-time control. The wide 1.8V-3.6V Vdd range supports single-cell Li-ion, two-cell coin-cell, and 3.3V regulated rails. The hardware I2C block supports both Standard-mode (100 kHz) and Fast-mode (400 kHz) operation with dedicated baud-rate generator, freeing the core from bit-banging overhead. Typical applications include capacitive-touch user interfaces, LED lighting controllers, small appliances, sensor nodes, and battery-powered IoT endpoints. Its tiny 8-pin footprint and mTouch capability make it well suited for replacing mechanical buttons and sliders in consumer white goods. When designing with this device, ensure input supply decoupling with a 0.1 µF ceramic capacitor placed close to Vdd. For mTouch applications, follow Microchip application notes on PCB layout and guard-ring techniques to achieve stable capacitive measurements under environmental noise. This page synthesizes distributor pricing, drop-in alternative listings, and practical design notes not found in the manufacturer datasheet.

견적 요청 문의하기

PIC12LF1552-E/SN

PIC12LF1552-E/SN - 8-Bit 32MHz 3.5KB Flash MCU | Microchip

The Microchip Technology PIC12LF1552-E/SN is an 8-bit PIC® 12F-series microcontroller featuring a 32MHz internal oscillator, 3.5KB (2K x 14) Flash program memory, 256 bytes of RAM, and a 10-bit ADC, housed in an 8-pin SOIC (SN) package. It is one of the smallest and lowest-cost PIC microcontrollers with hardware I2C support, designed for space-constrained embedded designs. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash), volatile data memory (RAM), and peripheral interfaces such as ADC, timers, and communication ports. PIC12F-series MCUs sit at the low end of the PIC12 architecture, optimized for cost-sensitive applications that need only 6 I/O pins and minimal code space. Within Microchip's broader hierarchy, the PIC12LF1552 belongs to PIC microcontroller -> 8-bit MCU -> embedded controller -> semiconductor IC. Key features include 32MHz CPU speed (8MHz instruction cycle with 4x PLL), hardware I2C/SPI, 6 I/O pins, a 10-bit ADC with up to 4 channels, multiple timer modules, and an internal 32kHz LFINTOSC. The 'LF' prefix denotes the wide 1.8V-3.6V supply range suited to battery-powered systems, and the 'E' suffix indicates the -40C to +125C extended operating temperature grade. The PIC12LF1552 uses a RISC-based Harvard architecture with 14-bit instruction words, 8-bit data path, and 49 instruction opcode set. This yields compact code density and deterministic interrupt latency, making it well-suited to real-time control tasks where predictable timing is critical. Typical applications include consumer electronics remote controls, low-cost sensor nodes, LED lighting controllers, capacitive touch HMI (mTouch), small appliance control, and battery-powered IoT edge devices. Its hardware I2C and tiny footprint also suit wearable and disposable medical accessories. When designing, note that 3.5KB Flash limits code size; consider the PIC12LF1552-E/P (PDIP) variant for through-hole prototyping or PIC12LF1552T-I/SN for tape-and-reel volume production. Always decouple VDD with a 0.1uF ceramic cap placed within 3mm of the pin.

견적 요청 문의하기

PIC12LF1552-I/MU

PIC12LF1552-I/MU - 8-bit 32MHz MCU, 3.5KB Flash | Microchip

The Microchip Technology PIC12LF1552-I/MU is a low-power 8-bit PIC microcontroller featuring a 32 MHz internal oscillator, 3.5 KB (2K x 14) Flash program memory and 256 bytes of SRAM, housed in an 8-pin UDFN (2x3 mm) exposed-pad surface-mount package. It belongs to the PIC12F family and integrates Microchip's mTouch capacitive-touch sensing peripherals alongside configurable logic cells (CLC), a Numerically Controlled Oscillator (NCO), and a 10-bit ADC with computation (ADC2). What is a PIC microcontroller? A PIC microcontroller (Peripheral Interface Controller) is a self-contained microcomputer that integrates a CPU core, program memory (Flash), data memory (RAM), and peripherals such as timers, ADC, communication interfaces, and I/O ports onto a single silicon die. PIC MCUs sit in the broader hierarchy of embedded microcontrollers -> microcontrollers -> microcomputer -> semiconductor -> integrated circuit. The PIC12LF series specifically targets ultra-low-power, space-constrained applications where a small pin count, low operating voltage, and integrated analog peripherals matter most. Key features of the PIC12LF1552 include 1.8V to 3.6V single-supply operation, 4 KB total Flash address space, 6 I/O pins, hardware mTouch capacitive sensing, 4 CLC blocks, a 10-bit ADC with 7 channels, 2 comparators, 1 8-bit and 1 16-bit timer, an EUSART module, and an internal 32 MHz oscillator that eliminates the need for an external crystal. The UDFN-8 (2x3) package enables compact PCB designs in wearables and IoT endpoints. The device uses Microchip's enhanced mid-range 8-bit core with a 14-bit instruction word, executing most instructions in a single clock cycle. The integrated ADC2 (Analog-to-Digital Converter with Computation) performs averaging, filtering, threshold comparison, and oversampling in hardware, reducing firmware complexity and CPU wake-time. The NCO block provides high-resolution frequency generation suitable for dimming LED drivers, IR carrier generation, and tone synthesis without CPU intervention. Typical applications include IoT sensor nodes, wearable fitness and health devices, consumer remote controls, LED lighting controllers, capacitive-touch user interfaces, low-end battery-powered toys, and small home appliances. The wide 1.8V-3.6V range supports single-cell Li-ion and 2xAA/AAA battery chemistries directly. When designing with the PIC12LF1552, ensure the exposed thermal pad (EP) is soldered to a ground copper pour for thermal dissipation and electrical reference. Decouple VDD with a 0.1 µF X7R ceramic capacitor placed within 2 mm of the IC, and reserve the MCLR pin configuration carefully if in-circuit serial programming (ICSP) is required.

견적 요청 문의하기

PIC12LF1552-I/P

PIC12LF1552-I/P - 8-bit MCU, 32MHz, 3.5KB Flash, 10-bit ADC | Microchip

The Microchip Technology PIC12LF1552-I/P is an 8-bit PIC microcontroller in the PIC12F family, featuring a 32MHz internal oscillator, 3.5KB Flash program memory, 256 bytes RAM, 6 I/O pins, a 10-bit ADC with up to 4 channels, and a 5-bit DAC, all housed in an 8-pin PDIP through-hole package. It operates from 1.8V to 3.6V with typical consumption of 3.3V, delivering 32MHz MIPS performance at very low current for cost-sensitive embedded designs. What is an 8-bit microcontroller? An 8-bit microcontroller is a single-chip computer that processes data 8 bits at a time, integrating a CPU, memory, and peripherals. It belongs to the hierarchy: microcontroller -> embedded processor -> semiconductor. The PIC12F series targets compact, low-pin-count applications where board space and BOM cost matter more than raw throughput. The 12LF variant uses Flash program memory, enabling in-circuit reprogramming and faster development iteration. Key features include a high-precision 32MHz internal oscillator, an integrated mTouch capacitive touch sensing peripheral, a 10-bit ADC with acquisition timer, a 5-bit DAC for analog output or trimming, and an enhanced PWM module. The device also offers a watchdog timer, in-circuit debug capability, and low-power sleep modes typical of the PIC12F architecture. The integrated mTouch block eliminates the need for external touch controller ICs in capacitive touch interfaces. The PIC12LF1552 uses Microchip's enhanced mid-range 8-bit core with a 14-bit instruction word and a 2-level hardware stack, supporting 49 instructions. Its 3.5KB Flash (2048 instruction words x 14 bits) and 256-byte SRAM are partitioned for C-compiler-friendly access, making it suitable for both assembly and XC8 C development. The on-chip peripherals share I/O pins via peripheral pin select (PPS) equivalents in the PIC12F family, simplifying PCB routing in 8-pin layouts. Typical applications include capacitive touch user interfaces (buttons, sliders, proximity sensors), LED lighting control with PWM dimming, sensor node readouts with on-chip ADC, low-cost consumer remote controls, and battery-powered IoT endpoints. The 8-pin PDIP package is breadboard-friendly, making the part well suited for hobby, prototyping, and educational use. Designers also deploy it in industrial human-machine interface (HMI) front panels and small appliance control boards. When designing with the PIC12LF1552, allocate at least one I/O pin for ICSP programming/debug (typically ICSPCLK/ICSPDAT). Place a 0.1uF decoupling capacitor within 5mm of VDD, and follow Microchip AN1202 for PCB layout of the mTouch sensing electrodes. The wide operating voltage of 1.8V-3.6V enables direct Li-ion battery operation. This page consolidates distributor pricing, drop-in same-brand and cross-brand alternatives, and practical design guidance not found in the manufacturer datasheet, giving engineers a faster path from concept to prototype.

견적 요청 문의하기

PIC12LF1552T-I/MU

PIC12LF1552T-I/MU - 8-bit MCU 3.5KB Flash 32MHz 8-UDFN | Microchip

The Microchip Technology PIC12LF1552T-I/MU is an 8-bit PIC microcontroller based on the enhanced mid-range core, delivering up to 32 MHz CPU performance with 3.5 KB Flash program memory and 256 bytes RAM, packaged in a compact 8-pin UDFN (2x3 mm). The device integrates a 4-channel 10-bit Analog-to-Digital Converter (ADC), advanced Capacitive Voltage Divider (CVD) controls for mTouch capacitive sensing, a configurable MI2C/SPI peripheral set, and a 32 MHz internal oscillator. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, and configurable peripherals into one IC. Within the broader taxonomy, the PIC12LF1552 belongs to the 8-bit PIC family -> mid-range enhanced core -> embedded microcontroller -> microcomputer -> semiconductor. The "LF" suffix denotes a wide Vdd range (1.8 V to 3.6 V) optimized for low-power and battery applications, while the "/MU" suffix identifies the 2x3 mm 8-UDFN surface-mount package, ideal for space-constrained designs. Key features include 25 mA source/sink current per I/O, a Low-Power Brown-Out Reset (LPBOR) for reliable startup, an extended Watchdog Timer with its own oscillator, and a mTouch CVD peripheral supporting proximity sensing, button matrices, and water-rejection algorithms. The 16 MHz internal oscillator can be multiplied to 32 MHz via the PLL, simplifying BOM by removing external crystals in many designs. Typical applications span capacitive touch user interfaces, low-power IoT sensor nodes, battery-powered consumer devices, and LED lighting controllers. The integrated CVD engine removes the need for an external touch controller, reducing BOM cost and PCB area. Wide 1.8 V to 3.6 V operation supports direct Li-ion or 2xAA battery connection. When designing with this MCU, allocate at least one GP port for ICD debugging and provide a robust ground plane under the UDFN thermal pad to maximize RF immunity for capacitive measurements. Decouple Vdd with a 100 nF ceramic placed within 5 mm of the pin. This page synthesizes distributor pricing, drop-in package-compatible alternatives, and practical design notes not found in the manufacturer datasheet.

견적 요청 문의하기

PIC12LF1552T-I/SN

PIC12LF1552T-I/SN - 8-bit MCU, 3.5KB Flash, 32MHz, 8-SOIC | Microchip

The Microchip Technology PIC12LF1552T-I/SN is an 8-bit PIC microcontroller featuring 3.5KB Flash program memory, 256 bytes RAM, 32MHz maximum CPU clock, and a 10-bit ADC, housed in an 8-pin SOIC package supplied on tape and reel. It is part of the PIC12F mid-range family targeting low-cost capacitive-touch (mTouch) and general-purpose embedded applications. An 8-bit microcontroller (MCU) is a small computer-on-a-chip that integrates a CPU, program memory (Flash/ROM), data memory (RAM), and peripherals such as timers, ADC, and communication interfaces into a single IC. The PIC12LF1552 belongs to the enhanced mid-range PIC12 architecture with the x14 instruction set (49 instructions, 200 ns instruction execution at 20 MHz). This category sits within the broader hierarchy of microcontrollers -> embedded processors -> semiconductors -> integrated circuits, and is widely used in low-power, cost-sensitive, pin-constrained designs. Key features of this device include 6 I/O pins, an internal 16 MHz oscillator, a 10-bit ADC with up to 4 channels, mTouch capacitive-touch sensing peripherals, an 8-bit timer with prescaler, and wide 1.8V to 3.6V operating voltage supporting both LF and HV (PIC12HV1552) variants. The 32 MHz operation is achieved via the internal oscillator or an external crystal, and the device supports in-circuit serial programming (ICSP). Technically, the PIC12LF1552 implements Microchip's enhanced mid-range 8-bit core with a 14-bit instruction word, 16-level hardware stack with overflow/underflow reset, automatic interrupt context saving, and direct/indirect/relative addressing modes. The on-chip peripherals are mapped through Peripheral Pin Select (PPS)-like fixed mappings, and the device integrates a temperature indicator, eeprom emulation in flash, and low-power sleep modes typical of the PIC12F family. Typical applications include capacitive touch buttons, sliders and proximity sensors, low-cost remote controls, LED lighting controllers, battery-powered sensor nodes, and small home-appliance user interfaces. The combination of low pin count (8-pin), low voltage operation, mTouch peripheral support, and small Flash footprint makes it ideal for replacing electromechanical switches with solid-state touch interfaces. When designing with this device, ensure decoupling capacitors (100 nF and 10 uF) are placed close to VDD, follow Microchip's mTouch layout guidelines for touch electrodes, and verify supply ramp timing for brown-out reset behavior. Programming can be performed via ICSP using Microchip's MPLAB X IDE and PICkit programmers. This page synthesizes distributor pricing, same-package drop-in alternatives, and practical design notes drawn from Microchip's published PIC12LF1552 datasheet, complementing the standard datasheet content with engineer-focused selection guidance.

견적 요청 문의하기

PIC12LF1571-E/P

PIC12LF1571-E/P - 8-Bit MCU, 1.75KB Flash, 32MHz, 16-bit PWM | Microchip

The Microchip Technology PIC12LF1571-E/P is an 8-bit RISC microcontroller from the PIC12F family, delivering 32MHz CPU performance with 1.75KB (1K x 14) of Flash program memory, 128 bytes of SRAM, and an integrated 16-bit PWM peripheral. Packaged in an 8-pin PDIP through-hole format, the device operates from a low 1.8V to 3.6V supply, making it suited to battery-backed and energy-harvesting designs. Core independent peripherals include a 4-channel 10-bit ADC, a 5-bit DAC, a comparator, and three 16-bit PWMs with independent timers, enabling high-resolution control without taxing the CPU. An 8-bit microcontroller (MCU) is a small computer-on-a-chip built around an 8-bit data path, integrating a CPU, non-volatile program memory, working RAM, and a set of digital and analog peripherals. Microcontrollers sit in the broader embedded semiconductor hierarchy between discrete logic and full microprocessors: simpler than application processors, more capable than logic ICs. The PIC12LF1571 belongs to Microchip's PIC10/12/16 baseline and mid-range families, all using a Harvard RISC core optimized for deterministic interrupt response and ultra-low static power consumption. Key differentiating features include three independent 16-bit PWMs (vs. the typical 10-bit PWM on baseline PIC devices), a 5-bit DAC reference for analog set-point generation, and on-board Core Independent Peripherals (CIPs) such as the Complementary Waveform Generator (CWG) and Numerically Controlled Oscillator (NCO). These offload timing-critical tasks from the CPU, freeing cycles for application code. The 32MHz internal oscillator eliminates external crystal cost in many designs, while the 8-pin PDIP footprint suits breadboard and through-hole prototyping where SMD soldering is inconvenient. Typical applications include high-resolution LED lighting and color mixing, stepper motor and DC motor control via the 16-bit PWM, compact switch-mode power supply controllers, general-purpose timer replacement, and analog signal conditioning using the DAC and comparator pair. Industrial sensor signal chains also benefit from the 4-channel 10-bit ADC. When designing with this part, mind the 1.8V minimum VDD: connecting 5V logic directly to any I/O pin will exceed absolute-maximum ratings and require a level translator. The E suffix denotes the -40C to +125C extended operating temperature range suitable for industrial and automotive under-hood environments.

견적 요청 문의하기

PIC12LF1571-E/SN

PIC12LF1571-E/SN - 8-Bit 32MHz MCU, 1.75KB FLASH, 8-SOIC | Microchip

The Microchip PIC12LF1571-E/SN is an 8-bit PIC microcontroller from the PIC12F family running at 32 MHz, integrating 1.75 KB (1K x 14) of FLASH program memory, 128 bytes of SRAM, and 64 bytes of EEPROM, packaged in an 8-pin SOIC. The 'LF' variant operates from a wide 1.8V to 3.6V supply, targeting ultra-low-power embedded applications. The '-E' suffix indicates the extended -40C to +125C industrial/automotive operating temperature range, while '/SN' denotes the 8-SOIC (3.9 mm / 0.15 in) package supplied in tubes. A microcontroller (MCU) is an integrated circuit that combines a CPU core, program memory, data memory, and programmable peripherals into a single chip. The PIC12 family sits at the entry point of the 8-bit PIC architecture tree (PIC10/12/16/18), optimized for small-pin-count, low-cost designs. Within the broader taxonomy, an MCU is a type of microprocessor (MPU) -> central processing unit -> semiconductor IC. The LF prefix indicates the wide-Vdd, low-power process variant, distinguishing it from the standard F-series parts that run only at higher supply voltages. Key features of the PIC12LF1571 include three independent 16-bit PWMs with dedicated timers, ideal for high-resolution control tasks, plus a 10-bit ADC, a 5-bit DAC, an analog comparator, and the CWG (Complementary Waveform Generator) peripheral. The device also provides enhanced peripherals such as the Configurable Logic Cell (CLC) and the Numerically Controlled Oscillator (NCO) for frequency synthesis. The peripheral set supports applications ranging from LED lighting and motor control to general-purpose digital and analog signal conditioning. Architecturally, the PIC12LF1571 uses the enhanced mid-range PIC core with a 14-bit instruction word and a modified Harvard bus structure, providing deterministic instruction timing. The 32 MHz internal oscillator (with PLL multiplier from a 16 MHz source) yields a 125 ns instruction cycle, while the 16-bit PWM resolution at the slowest selectable clock allows sub-microsecond timing precision. On-chip peripherals are routed through the peripheral pin select (PPS) limited set, simplifying PCB layout compared to fixed-function MCUs. Typical applications include high-resolution LED lighting and color mixing, stepper motor and DC-motor control loops, low-cost switch-mode power supply controllers, ceiling-fan and small appliance control, and general-purpose sensor interfaces. The small 8-SOIC footprint and LF low-voltage operation also suit battery-powered IoT sensor nodes, wearables, and remote controls where board area and quiescent current are at a premium. When designing with this device, budget for at least 2.0V rail headroom if using the analog comparator or ADC at full speed, and select the 8 MHz HFINTOSC mode when EMC compliance demands lower switching harmonics. For new designs, prefer the PIC12LF1572 (same family with more peripherals and pins) when additional timers are required, or the PIC16F1xxx family when migrating to a 16-bit PWM core is desirable. This page synthesizes distributor pricing from DigiKey and Mouser, parametric drop-in alternatives verified against the Microchip datasheet (40001723D), and practical design notes covering oscillator selection and PWM output filtering that are not consolidated in the manufacturer datasheet.

견적 요청 문의하기

PIC12LF1571-I/MF

PIC12LF1571-I/MF - 8-Bit MCU, 32MHz, 1.75KB Flash | Microchip

The Microchip Technology PIC12LF1571-I/MF is an 8-bit PIC microcontroller with 32 MHz CPU speed, 1.75 KB (1K x 14) Flash program memory and 128 bytes of RAM, housed in an 8-pin DFN (3x3 mm) package with exposed pad. It is a member of the PIC12(L)F1571 family that combines three independent 16-bit PWMs with on-chip analog peripherals for high-resolution control applications. A microcontroller (MCU) is a single-chip computer containing a CPU core, non-volatile program memory, working RAM, and a mix of analog and digital peripherals. PIC12F-series MCUs from Microchip use a RISC architecture optimized for deterministic, low-latency control loops with low active and sleep current. PIC12LF variants add an 'L' suffix for the low-voltage (1.8 V to 3.6 V) operating range, which extends battery life in portable designs. Key features of the PIC12LF1571-I/MF include three 16-bit PWMs with independent timers for high-resolution outputs, a 10-bit ADC with computation, on-chip comparators, and an internal configurable logic cell (CLC). The device operates from 1.8 V to 3.6 V supply, supports eXtreme Low Power (XLP) sleep currents down to the nA range, and provides in-circuit serial programming (ICSP) for field upgrades. The 8-pin DFN package exposes a thermal pad that must be soldered to the PCB ground plane for both electrical grounding and thermal dissipation. The architecture is built around a 14-bit instruction word with a single accumulator and hardware stack, prioritizing deterministic interrupt latency over raw throughput. Typical applications for this device include LED lighting and color-mixing control, stepper motor drivers, power-conversion feedback loops, and compact sensor nodes in IoT edge devices where the small 3x3 mm footprint is required. When designing with this MCU, place a 100 nF decoupling capacitor close to VDD and tie the exposed pad to a clean ground pour. Ensure ICSP programming lines (ICSPCLK/ICSPDAT) are accessible on the PCB for in-circuit programming. This page consolidates distributor pricing, drop-in alternatives, and design considerations drawn from multiple sources, delivering practical engineering context beyond what is found in the manufacturer datasheet.

견적 요청 문의하기

PIC12LF1571T-I/MF

PIC12LF1571T-I/MF - 8-bit MCU 32MHz 1.75KB Flash 8-DFN | Microchip

The Microchip Technology PIC12LF1571T-I/MF is an 8-bit PIC12 microcontroller with 1.75 KB (1K x 14) Flash program memory, 128 bytes SRAM, and 6 I/O pins, operating at up to 32 MHz in a compact 8-pin DFN (3x3 mm) package with exposed pad. The device integrates three independent 16-bit PWMs, a 10-bit ADC, a 5-bit DAC, a comparator, and a Configurable Logic Cell (CLC) / Complementary Waveform Generator (CWG), enabling direct synthesis of mixed-signal waveforms without external components. Tape-and-reel ('T') and 'I' industrial temperature grade (-40C to +85C) make the part designed for volume production. A PIC microcontroller is a low-power, Harvard-architecture 8-bit RISC processor family developed by Microchip Technology that combines CPU core, Flash program memory, SRAM, EEPROM, and configurable peripherals on a single die. The PIC12 sub-family is the 'baseline + mid-range' ultra-small-footprint line: PIC12F/12LF parts target 6-20 pin packages with 0.5-2 KB Flash, used where PCB area and BOM cost matter more than raw CPU throughput. The PIC12LF variants are the low-voltage ('L') family, capable of operating down to 1.8V, while standard PIC12F devices operate from 2.0V. Within this taxonomy, PIC12F1571 is the next-generation 'enhanced mid-range' part that supersedes older PIC12F615/617/609 devices. Key features include 32 MHz maximum CPU clock (8 MHz internal oscillator), three 16-bit PWM channels with independent timers (suitable for high-resolution LED lighting and stepper motor control), 4-channel 10-bit ADC, one 5-bit DAC, one comparator, and on-chip CWG that can generate complementary, dead-band-controlled signals for half-bridge drivers. The 8-DFN package has a thermal pad that must be soldered to the PCB ground pour for proper thermal dissipation at 32 MHz operation. Architecture is the Microchip enhanced mid-range 8-bit core with 49 instructions, single-cycle execution (except branches), 16-level hardware stack, and a separate 14-bit instruction word. The 1.75 KB self-programmable Flash supports in-circuit serial programming (ICSP) via two pins, enabling firmware updates after PCB assembly. The device includes an internal 16 MHz HFINTOSC with +/- 2% typical accuracy, eliminating external crystals in cost-sensitive designs. Typical applications include high-density LED lighting controllers (RGB, RGBA, and decorative strands), stepper motor microstepping drivers, switching power supply PWM controllers, ceiling-fan and small-bldc motor controllers, e-bike and small-EV lighting, and battery-powered IoT sensor nodes. The combination of 16-bit PWM, CWG, and 5-bit DAC is unusual for an 8-pin device and gives this part a unique position in cost-constrained analog-front-end designs. When designing, note that the 8-DFN (3x3 mm) package requires a PCB land pattern with an exposed thermal pad that MUST be soldered to a grounded copper pour - skipped thermal pads cause 25-30 C/W higher junction-to-ambient thermal resistance and can lead to erratic oscillator behavior. The ICSP programming pins (ICSPCLK/ICSPDAT) are multiplexed with GPIO; the configuration bits must be set correctly to disable the MCLR pin or enable internal weak pull-ups if MCLR is unused. This page synthesizes distributor pricing, verified same-family drop-in alternatives, and PCB layout notes not found in the manufacturer datasheet, providing a complete sourcing and engineering reference for the PIC12LF1571T-I/MF.

견적 요청 문의하기

PIC12LF1571T-I/MS

PIC12LF1571T-I/MS - 8-bit 32MHz MCU, 1.75KB Flash, MSOP-8

The Microchip Technology PIC12LF1571T-I/MS is an 8-bit RISC PIC12 microcontroller featuring a 32MHz CPU, 1.75KB (1K x 14) of Flash program memory, 128 bytes of SRAM, and 128 bytes of EEPROM data memory, housed in an 8-pin MSOP package. It operates from 1.8V to 3.6V and integrates three 16-bit PWMs with independent timers, a 10-bit ADC, a comparator, and a 5-bit DAC on-chip. An 8-bit microcontroller (MCU) is a small computing system-on-chip that combines a CPU, RAM, non-volatile program memory, and peripherals into a single IC. The PIC12 family sits within Microchip's PIC architecture family of microcontrollers -> 8-bit MCU category -> embedded computing IC -> semiconductor device. 8-bit MCUs are widely deployed in cost- and power-constrained embedded applications because they deliver deterministic instruction execution and very low active/standby current at low BOM cost. Key features of this device include a maximum 32MHz internal oscillator, six general-purpose I/O pins, a 10-bit ADC with up to 4 input channels, one comparator with selectable reference, a 5-bit DAC, three independent 16-bit PWMs, and an Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART). The 'LF' prefix denotes the wide-voltage low-power variant supporting 1.8V to 3.6V operation, ideal for battery-powered designs. Architecturally, the PIC12LF1571 uses Microchip's enhanced mid-range 8-bit core with a single-cycle instruction set, hardware stack, and interrupt controller. The 16-bit PWM modules with independent timers deliver high-resolution pulse-width modulation that competes with 16-bit MCU peripherals at 8-bit cost, enabling precision control loops for LED drivers, fans, and small motor drives without external timer ICs. Typical applications include LED lighting color-mixing and dimming control, battery-powered IoT sensor nodes, small DC fan or motor PWM control, consumer remote controls, and general-purpose logic replacement where simple sequencing and analog measurement are required. The on-chip comparator and 5-bit DAC allow threshold detection and waveform generation without external components. When designing with this device, evaluate whether the 1.75KB Flash and 128 bytes of RAM meet application requirements - small protocol stacks or BLE radio drivers typically cannot fit. Plan for ICSP programming header access (PGD/PGC) and ensure adequate decoupling per the manufacturer application notes for noise-sensitive ADC measurements. This page synthesizes distributor pricing, drop-in alternatives within the PIC12/MSOP-8 footprint, and practical design notes not consolidated in the manufacturer datasheet.

견적 요청 문의하기

PIC12LF1571T-I/RF

PIC12LF1571T-I/RF - 8-bit MCU, 1.75KB Flash, 16-bit PWM | Microchip

The Microchip Technology PIC12LF1571T-I/RF is an 8-bit PIC RISC microcontroller with 1.75KB Flash program memory, 128 bytes of RAM, and an integrated 16-bit PWM peripheral, supplied in an 8-pin UDFN exposed-pad package supplied on Tape & Reel. A PIC microcontroller (Peripheral Interface Controller) is a family of 8-bit RISC-based microcontrollers from Microchip Technology built on a Harvard architecture with separate program and data buses. Within the PIC hierarchy this part belongs to PIC12 -> PIC12F -> PIC12LF1571. The LF suffix indicates a wide-voltage (2.5V/3.3V/5V) process node allowing operation down to 1.8V, ideal for battery-powered and energy-harvesting designs. Key features of the PIC12LF1571T-I/RF include three independent 16-bit PWM channels for high-resolution timing, a 32 MHz internal oscillator, 6 I/O pins in an 8-pin UDFN with exposed thermal pad, and on-chip peripherals such as a 10-bit ADC, comparators, EUSART, MSSP (I2C/SPI) and configurable logic cells. The 16-bit PWM with 32 MHz clock delivers sub-microsecond edge resolution suited to LED dimming and motor control. The PIC12LF1571 architecture uses a 14-bit instruction word with a 32-byte register file and a single-cycle ALU, enabling predictable deterministic timing critical for real-time control. The LF variant uses the same core as the PIC12F1571 but with a wider voltage range and lower-power Brown-out Reset and Watchdog Timer configuration, making it suitable for low-voltage battery systems. Typical applications include high-resolution LED lighting control, stepper motor and DC motor drive PWM generation, switched-mode power supply control loops, fan speed controllers, and small sensor-conditioning platforms. Designers choose this part where board area is constrained and 16-bit PWM resolution removes the need for an external timer IC. When designing with this part, ensure that the ICSP programming pins (ICSPCLK/ICSPDAT) are accessible on the PCB for in-circuit programming and debugging, and that the exposed thermal pad on the UDFN package is soldered for both thermal dissipation and mechanical reliability. The wide 1.8V-3.6V supply range simplifies integration into 2x AA, coin-cell, or Li-Ion battery systems. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical PCB design notes that complement the manufacturer datasheet for engineers selecting the PIC12LF1571T-I/RF.

견적 요청 문의하기

PIC12LF1572-E/RF

PIC12LF1572-E/RF - 8-bit MCU, 32MHz, 3.5KB Flash, 16-bit PWM | Microchip

The Microchip Technology PIC12LF1572-E/RF is an 8-bit PIC12 microcontroller delivering 32MHz CPU performance with 3.5KB (2K x 14) Flash program memory and 256 bytes RAM in an 8-pin UDFN (3x3mm) package. The device integrates three independent 16-bit PWMs with dedicated timers, a 10-bit ADC, configurable logic cells (CLC), and a complementary waveform generator (CWG) targeting LED lighting, stepper motor, and power-conversion applications. A microcontroller (MCU) is a single-chip computer containing a CPU, program memory (Flash), data memory (RAM), and programmable peripherals. The PIC12LF1572 belongs to the PIC® 12F family of 8-pin mid-range microcontrollers; this LF variant operates from 1.8V to 3.6V and is optimized for low-voltage, low-power designs. Within the broader taxonomy, an MCU is a subset of microcomputer -> embedded processor -> integrated circuit. The PIC12LF1572 family pairs a RISC Harvard-architecture core with Core Independent Peripherals (CIPs) so timers, PWM, and logic blocks run without CPU intervention, enabling deterministic real-time control with minimal code overhead. Key features include three 16-bit PWMs (1.0ns PWM resolution at 32MHz) for high-resolution dimming and motor control, four 10-bit ADC channels with hardware averaging, two comparators, two CLCs, and one CWG with auto-shutdown. The device supports in-circuit serial programming (ICSP), provides 25mA source/sink per I/O, and includes a low-power sleep mode with <50nA typical current. Two speed grades and an extended (-40C to +125C) temperature option make it suitable for industrial and consumer-grade applications. The PIC12LF1572 uses an enhanced mid-range 8-bit core with a 14-bit instruction word, 8-level hardware stack, and interrupt controller with hardware context save. CIPs (PWM, CLC, CWG) execute autonomously, freeing the CPU for system-level tasks and reducing firmware complexity. The 1.8V minimum VDD allows direct Li-ion or 2xAA battery operation without external regulators. Typical applications include LED lighting color-mixing and dimming, brushed DC motor and stepper control, switched-mode power supply (SMPS) feedback loops, and consumer remote controls. The three 16-bit PWMs are particularly well suited to high-resolution RGB or white-LED dimming where 8 or 10-bit PWM granularity is insufficient. When designing with the PIC12LF1572-E/RF, ensure VDD decoupling includes a 100nF ceramic capacitor placed within 5mm of the VDD pin, and use a 10kohm pull-up on MCLR for reliable ICSP programming. The UDFN 3x3mm package has an exposed thermal pad that should be soldered to the ground plane for mechanical reliability. This page consolidates distributor pricing, drop-in PIC12F1571/1572 family alternatives, and practical design notes not aggregated in the manufacturer datasheet alone.

견적 요청 문의하기

PIC12LF1572-E/SN

PIC12LF1572-E/SN - 8-bit MCU, 32MHz, 3.5KB Flash, 16-bit PWM | Microchip

The Microchip Technology PIC12LF1572-E/SN is an 8-bit RISC microcontroller from the PIC12 family, featuring a PIC12 CPU core operating at up to 32MHz, 3.5KB (2K x 14) of Flash program memory, 256 bytes of RAM, and 128 bytes of Data EEPROM, housed in an 8-pin SOIC (SN) package. It operates from a wide 1.8V to 3.6V supply and integrates three independent 16-bit PWM channels, six timers, a comparator, an EUSART, a brown-out reset (BOR), a power-on reset (POR), and a watchdog timer (WDT). An 8-bit microcontroller (MCU) is a compact computing-on-a-chip built around an 8-bit data path, integrating CPU, RAM, non-volatile program memory, and peripheral I/O on a single silicon die. Within the broader semiconductor taxonomy, the PIC12LF1572 sits under MCU -> microcontroller -> embedded controller -> semiconductor, optimized for low-pin-count, low-power, mixed-signal embedded designs where deterministic real-time response, low sleep current, and small footprint are critical. Key features of this device include three 16-bit PWMs with independent timers that deliver high-resolution control ideal for LED lighting, stepper motors, and switched-mode power supplies. The integrated high-performance comparator supports mixed-signal feedback loops, while the EUSART provides robust asynchronous and synchronous serial communication. The LF process node (low-voltage, low-power) enables deep sleep currents in the nanoampere range, extending battery life in energy-harvesting applications. The architecture uses a Harvard-class RISC core with a 14-bit instruction word and a 200 ns instruction execution time at 20 MHz (one instruction per 4 clock cycles in this device), and offers Core Independent Peripherals (CIPs) that operate without CPU intervention. Three 16-bit PWM outputs, a 5-bit DAC, and the 16-bit timer/counter can be interconnected via the peripheral pin select and PPS-less fabric to form closed-loop analog or feedback control paths. Typical applications include LED lighting and color-mixing control, stepper motor and DC motor drive for low-power robotics, switch-mode power supply feedback, battery management and metering, IoT end-node sensor conditioning, and general-purpose industrial automation. The wide operating voltage range and ultra-low power modes also make the part attractive for handheld instruments and remote sensor nodes. When designing with this device, place a 0.1 uF decoupling capacitor as close as possible to VDD and use a 10 uF bulk capacitor on the supply rail. Confirm that the chosen programming tool (e.g., PICkit 4 or MPLAB SNAP) supports the PIC12LF1572 device ID before board bring-up. Do not exceed the absolute maximum VDD of 4.0V; the LF variant is not 5V tolerant. This page synthesizes distributor pricing, pin-compatible drop-in alternatives, application notes, and practical design notes not found in the manufacturer datasheet, giving embedded engineers a faster path from part selection to prototype.

견적 요청 문의하기

PIC12LF1572-I/MF

PIC12LF1572-I/MF - 8-Bit 32MHz MCU 3.5KB Flash | Microchip

The Microchip Technology PIC12LF1572-I/MF is an 8-bit RISC PIC microcontroller featuring a PIC12 CPU core, operating at up to 32MHz and integrating 3.5KB (2K x 14) of Flash program memory with 256 bytes of RAM in an 8-pin DFN (3x3) package. As the 'LF' variant, it supports an extended low-voltage operating range of 1.8V to 3.6V, making it suited to battery-powered and energy-harvesting applications. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path, Flash program memory, RAM, and on-chip peripherals such as timers, ADCs, and PWMs. PIC microcontrollers from Microchip use a Harvard RISC architecture, where program and data buses are separate, enabling single-cycle instruction execution and deterministic timing. The PIC12LF1572 belongs to the PIC12 sub-family of low-pin-count 8-bit MCUs and sits within Microchip's broader product hierarchy: 8-bit MCU -> PIC microcontroller -> PIC12 family -> PIC12F sub-family -> power-management/lighting-oriented PIC12LF157x series. Its place in this taxonomy makes it a common building block in compact, low-cost embedded designs. Key features of the PIC12LF1572 include three independent 16-bit PWMs with dedicated timers, high-resolution analog peripherals, a 10-bit ADC, comparators, EUSART (Enhanced Universal Synchronous Asynchronous Receiver Transmitter) for serial communication, and Core Independent Peripherals (CIPs) that offload tasks from the CPU. The 16-bit PWM channels are the headline feature, providing fine-grained duty cycle control needed for LED dimming, motor control, and switch-mode power supply regulation. The device also supports high-voltage In-Circuit Serial Programming (ICSP) for flexible programming in production. Typical applications include LED lighting drivers (RGB and white), stepper motor control, DC-DC converter control loops, battery chargers, and small general-purpose embedded control boards. The 1.8V minimum supply allows direct connection to single-cell Li-Ion or two-cell alkaline battery stacks. Combined with its tiny 3x3 mm DFN footprint, the part enables very compact PCB designs in cost-sensitive consumer and industrial products. When designing with this part, place a 0.1uF decoupling capacitor close to the VDD pin and respect the 1.8V-3.6V supply range. For low-power sleep modes, configure the CPU and peripherals carefully via the SLP and IDLE bits to minimize quiescent current. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

견적 요청 문의하기

PIC12LF1572-I/MS

PIC12LF1572-I/MS - 8-bit 32MHz 3.5KB Flash MCU | Microchip

The Microchip Technology PIC12LF1572-I/MS is an 8-bit PIC microcontroller from the PIC12(L)F1571/2 family, combining three independent 16-bit PWMs with 10-bit ADC and analog peripherals in an 8-pin MSOP package. It runs at up to 32MHz, integrates 3.5KB Flash program memory (2K x 14 words), 256 bytes of RAM, and operates across a wide 1.8V to 3.6V supply range suitable for battery-powered designs. A microcontroller (MCU) is a single-chip computer containing a CPU, non-volatile program memory (Flash), volatile data memory (RAM), and programmable I/O. Within the broader device hierarchy, an MCU is a type of embedded processor (microprocessor with integrated peripherals) classified under microcontrollers, then 8-bit microcontrollers, then the PIC family. The 8-bit PIC RISC architecture executes most instructions in one clock cycle, enabling deterministic timing that is valuable for real-time control loops such as PWM generation, motor commutation, and sensor sampling. Key features include three independent 16-bit PWMs with their own timers (suitable for high-resolution LED dimming and stepper motor control), a 10-bit ADC with computation (ADC2), a comparator, EUSART (Enhanced USART) for serial communication, and an internal 31kHz to 32MHz oscillator. The LF (low-power) silicon variant extends the supply range down to 1.8V, making it a strong fit for 2x AA / coin-cell applications. The device also supports the PICkit and ICD programming/debug toolchain for in-circuit development. Architecturally, the PIC12LF1572-I/MS uses a Harvard RISC core with separate program and data buses. The three 16-bit PWM modules can operate independently of CPU execution - once configured, they generate outputs without software intervention, freeing the core for measurement and communication. The 32MHz internal oscillator provides factory-calibrated accuracy and removes the need for external crystals in cost-sensitive designs. Typical applications include LED lighting controllers, battery-powered sensor nodes, handheld consumer products, fan and pump speed controllers, and general-purpose low-cost embedded control where compact 8-pin footprint and integrated 16-bit PWM resolution are required. The combination of three PWMs and 10-bit ADC makes it especially suited to closed-loop lighting and motor control. When designing with this part, ensure the supply rail is decoupled with 100nF + 10uF ceramic capacitance placed close to the VDD pin. For accurate ADC readings, configure the ADC2 averaging and add a low-pass RC filter at the analog input. The ICSP programming pins (ICSPCLK/ICSPDAT) share pads with GPIO and may require isolation resistors in production layouts. This page synthesizes distributor pricing, drop-in same-package alternatives (PIC12F1572-I/MS, PIC12LF1571-I/MS), and practical design notes not consolidated on a single manufacturer or distributor page.

견적 요청 문의하기

PIC12LF1572-I/P

PIC12LF1572-I/P - 8-bit MCU, 32MHz, 3.5KB Flash, 8-PDIP | Microchip

The Microchip PIC12LF1572-I/P is an 8-bit RISC microcontroller based on the enhanced mid-range PIC® core, operating up to 32MHz with 3.5KB (2K x 14) of Flash program memory and 256 bytes of SRAM, housed in an 8-pin PDIP through-hole package. It features three independent 16-bit PWM modules with complementary waveform outputs, a 10-bit ADC with 4 channels, a 5-bit DAC with 1 channel, and a high-performance comparator, all designed for mixed-signal applications in a compact 8-pin footprint. A microcontroller (MCU) is an integrated circuit containing a processor core, memory, and programmable input/output peripherals on a single silicon die. The PIC12LF1572 belongs to the PIC12 (L)F157x family from Microchip, which targets cost-sensitive embedded designs that need precision analog and PWM generation. The 'LF' suffix indicates a wide operating voltage range of 1.8V to 3.6V, making this part ideal for battery-powered and low-voltage systems where energy efficiency is critical. Key features include three 16-bit PWMs with independent timers delivering high-resolution pulse-width modulation suitable for LED lighting, stepper motor control, and switched-mode power supplies. The device integrates a 10-bit ADC, a 5-bit DAC, two comparators, an Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART), and 5-bit digital signal conditioning blocks (DSM). Its 32MHz internal oscillator eliminates external crystal requirements, reducing BOM cost and PCB area. The architecture uses a 14-bit instruction word with single-cycle execution except for program branches, providing deterministic timing. With 35 instructions and hardware stack depth of 16, this MCU simplifies code development in MPLAB® X IDE using XC8 compilers. The peripheral pin select (PPS) is not available on this 8-pin device, so pin assignments are fixed per the device datasheet. Typical applications include LED lighting drivers, brushless DC fan control, small stepper motor control, battery chargers, and general-purpose mixed-signal embedded control. The wide 1.8V-3.6V operating range and integrated analog peripherals reduce the external component count significantly. When designing with this MCU, ensure the supply voltage stays within the 1.8V to 3.6V LF range; the non-LF PIC12F1572 variant supports 2.3V to 5.5V. Decouple VDD with a 0.1uF ceramic capacitor placed within 5mm of the IC pins. The ICSP™ programming pins (ICSPCLK/ICSPDAT) are shared with GPIO, so design the PCB to allow in-circuit programming access during development.

견적 요청 문의하기

PIC12LF1572-I/RF

PIC12LF1572-I/RF - 8-Bit MCU, 3.5KB Flash, 3x16-bit PWM | Microchip

The Microchip Technology PIC12LF1572-I/RF is an 8-bit PIC microcontroller built around the enhanced mid-range core running at up to 32 MHz, delivering 3.5 KB (2K x 14) of self-programmable Flash program memory, 256 bytes of RAM, and housed in a compact 8-pin UDFN (3x3 mm) exposed-pad package. The device integrates three independent 16-bit PWMs with dedicated timers, a 10-bit ADC with 4 channels, a 5-bit DAC, two comparators, and an EUSART, making it one of the most feature-dense 8-pin microcontrollers in the PIC12 family. It operates from a wide 1.8V to 3.6V supply range, supporting low-voltage battery-powered designs including single-cell Li-ion and 2x AA alkaline topologies. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, and configurable peripherals. The PIC12 family is Microchip's baseline 8-pin PIC line, optimized for cost-sensitive applications where board space is at a premium. Within that hierarchy, the PIC12LF1572 belongs to the enhanced mid-range core generation with a C-compiler-optimized RISC architecture. Its place in the broader taxonomy is: 8-bit microcontroller -> embedded controller -> semiconductor IC. Compared to legacy PIC12F parts, the 1572 adds high-resolution 16-bit PWM channels specifically tuned for LED lighting, power conversion, and motor control. Key differentiating features include three independent 16-bit PWMs (vs. the typical 10-bit PWM found on older PIC12F parts), a 10-bit ADC up to 100 ksamples/s, an on-chip 5-bit DAC usable as a programmable voltage reference, two high-speed comparators, and an internally calibrated 32 MHz HFINTOSC. The device supports in-circuit serial programming (ICSP) via the standard Microchip ICD toolchain, and includes a watchdog timer, brown-out reset, and on-chip voltage reference for robust field operation. The architecture pairs an 8-bit data path with a 14-bit instruction word, allowing most instructions to execute in a single cycle. With 49 instructions and 16-level hardware stack, code density is high and interrupt latency deterministic - important for real-time PWM control loops. The integrated 16-bit PWM resolution means stepping granularity of about 488 Hz at a 32 MHz Fosc, a 256x improvement over 8-bit PWM, which is critical for digital LED dimming, where perceived flicker and color shift depend on PWM depth. Typical applications include LED lighting and RGB color mixing, stepper motor and DC motor control, switched-mode power supply feedback, capacitive-touch user interfaces, fan speed controllers, and general-purpose sensor hubs. The combination of three PWMs plus a 10-bit ADC plus a DAC makes the PIC12LF1572-I/RF a self-contained analog/digital front-end in a single 8-pin package. When designing with this part, verify that the UDFN exposed-pad is properly soldered and thermally connected to the ground plane; the EP serves as the primary thermal and electrical return path. Plan GPIO usage carefully - the 8-pin package exposes only 6 general-purpose I/O pins, of which several are multiplexed with the comparators, ADC, and PWM outputs. This page synthesizes distributor pricing from 9 sources, parametric comparison with same-footprint variants, and practical design notes not found in the manufacturer datasheet - covering drop-in alternatives in the UDFN-8 footprint and common thermal/layout pitfalls.

견적 요청 문의하기

PIC12LF1572T-I/MF

PIC12LF1572T-I/MF - 8-Bit MCU, 32MHz, 3.5KB Flash, 8-DFN | Microchip

The Microchip Technology PIC12LF1572T-I/MF is a low-power 8-bit PIC microcontroller from the PIC12(L)F157X family, operating at up to 32 MHz with 3.5 KB (2K x 14) of Flash program memory, 256 bytes of RAM, and housed in an 8-pin DFN (3x3 mm) package. The device integrates three independent 16-bit PWMs with dedicated timers, a 10-bit ADC, a comparator, and a configurable EUSART peripheral, making it purpose-built for high-resolution PWM applications such as LED lighting, stepper motor drive, and digital power conversion. An 8-bit microcontroller (MCU) is a small computer-on-a-chip built around an 8-bit data path; it executes one byte per instruction and is widely used in cost-sensitive embedded designs where deterministic timing and ultra-low standby power are more important than raw compute throughput. The PIC12F157X family adds 16-bit PWM channels to the traditional 8-bit core, which is unusual: most 8-bit MCUs offer only 8 or 10-bit PWM. This bridges the gap between low-cost 8-bit controllers and higher-end 16-bit Digital Signal Controllers for applications that demand fine-grained duty-cycle control without paying for a 16-bit core. Key features include three independent 16-bit PWMs (1.6 ns resolution at 32 MHz), an integrated 10-bit ADC with up to 6 channels, an analog comparator with a 4-bit DAC reference, an EUSART module for asynchronous serial communications, and four hardware-driven Core Independent Peripherals (CIPs) that operate without CPU intervention. The "LF" suffix denotes the wide-Vdd 1.8V-3.6V operating range, optimized for battery-powered and energy-harvesting designs. Brown-out Reset (BOR), Power-On Reset (POR), and a low-power Sleep mode (typically under 50 nA) support extended battery life in always-on products. Typical applications include LED lighting dimming and color-mixing controllers, brushed DC and stepper motor drivers, switched-mode power supply (SMPS) digital control loops, remote controls, sensor signal conditioning, and small-form-factor IoT edge nodes. The DFN-8 package makes the part attractive where board area is at a premium, such as in smart wearables or miniaturized sensor modules. When designing with this part, ensure the configured system clock does not exceed 32 MHz and that the EUSART baud-rate generator error is checked at the target temperature. Because the 16-bit PWM time-base can drive the part beyond what 8-bit timers typically achieve, plan filter component values and dead-time insertion carefully to avoid shoot-through in half-bridge drive applications. This page synthesizes distributor pricing, drop-in 8-pin alternatives, and practical design notes not found in the standalone datasheet PDF.

견적 요청 문의하기

하위 카테고리

제품 (38,000+)

PIC12LF1501-I/SN - 8-bit 20MHz 1.75KB Flash MCU | Microchip

PIC12LF1501T-I/MC - 8-bit MCU, 1.75KB Flash, 20MHz, 8-DFN | Microchip

PIC12LF1501T-I/MS - 8-Bit MCU, 1.75KB Flash, 20MHz, MSOP-8 | Microchip

PIC12LF1501T-I/SN - 8-Bit MCU 1.75KB Flash 20MHz | Microchip

PIC12LF1552-E/MS - 8-bit MCU, 3.5KB Flash, MSOP-8 | Microchip

PIC12LF1552-E/P - 8-bit MCU 32MHz 3.5KB Flash | Microchip

PIC12LF1552-E/SN - 8-Bit 32MHz 3.5KB Flash MCU | Microchip

PIC12LF1552-I/MU - 8-bit 32MHz MCU, 3.5KB Flash | Microchip

PIC12LF1552-I/P - 8-bit MCU, 32MHz, 3.5KB Flash, 10-bit ADC | Microchip

PIC12LF1552T-I/MU - 8-bit MCU 3.5KB Flash 32MHz 8-UDFN | Microchip

PIC12LF1552T-I/SN - 8-bit MCU, 3.5KB Flash, 32MHz, 8-SOIC | Microchip

PIC12LF1571-E/P - 8-Bit MCU, 1.75KB Flash, 32MHz, 16-bit PWM | Microchip

PIC12LF1571-E/SN - 8-Bit 32MHz MCU, 1.75KB FLASH, 8-SOIC | Microchip

PIC12LF1571-I/MF - 8-Bit MCU, 32MHz, 1.75KB Flash | Microchip

PIC12LF1571T-I/MF - 8-bit MCU 32MHz 1.75KB Flash 8-DFN | Microchip

PIC12LF1571T-I/MS - 8-bit 32MHz MCU, 1.75KB Flash, MSOP-8

PIC12LF1571T-I/RF - 8-bit MCU, 1.75KB Flash, 16-bit PWM | Microchip

PIC12LF1572-E/RF - 8-bit MCU, 32MHz, 3.5KB Flash, 16-bit PWM | Microchip

PIC12LF1572-E/SN - 8-bit MCU, 32MHz, 3.5KB Flash, 16-bit PWM | Microchip

PIC12LF1572-I/MF - 8-Bit 32MHz MCU 3.5KB Flash | Microchip

PIC12LF1572-I/MS - 8-bit 32MHz 3.5KB Flash MCU | Microchip

PIC12LF1572-I/P - 8-bit MCU, 32MHz, 3.5KB Flash, 8-PDIP | Microchip

PIC12LF1572-I/RF - 8-Bit MCU, 3.5KB Flash, 3x16-bit PWM | Microchip

PIC12LF1572T-I/MF - 8-Bit MCU, 32MHz, 3.5KB Flash, 8-DFN | Microchip