집적 회로

하위 카테고리

📁 ADC/DAC 3,100+ 제품 📁 증폭기 IC 1,700+ 제품 📁 오디오 코덱 18 제품 📁 오디오 IC 2 제품 📁 클록 및 타이밍 650+ 제품 📁 Comparator ICs 1 제품 📁 DSP 1,100+ 제품 📁 데이터 수집 IC 2 제품 📁 디지털 포텐셔미터 4 제품 📁 디스플레이 드라이버 및 컨트롤러 1 제품 📁 FPGA & CPLD 7,100+ 제품 📁 인터페이스 IC 3,100+ 제품 📁 LED 드라이버 1 제품 📁 로직 IC 450+ 제품 📁 메모리 IC 870+ 제품 📁 마이크로컨트롤러 20,000+ 제품 📁 마이크로프로세서 4 제품 📁 모터 드라이버 1 제품 📁 기타 1 제품 📁 Sensor and Detector Interfaces 1 제품 📁 특수 IC 15 제품 📁 비디오 IC 13 제품

제품 (38,000+)

PIC16C620AT-20/SS - 8-Bit OTP MCU 20MHz 896B SSOP-20 | Microchip
PIC16C620AT-20/SS

PIC16C620AT-20/SS - 8-Bit OTP MCU 20MHz 896B SSOP-20 | Microchip

The Microchip Technology PIC16C620AT-20/SS is an 8-bit PIC microcontroller from the PIC16C family, operating at up to 20 MHz with 896 bytes (512 x 14-bit words) of One-Time Programmable (OTP) program memory and 96 bytes of RAM, housed in a 20-pin SSOP package. The 'A' revision extends the PIC16C620 legacy with enhanced peripherals and the 'T' suffix denotes the tape-and-reel shipping format, while '20' indicates the 20 MHz maximum clock speed and '/SS' identifies the 0.209" (5.30 mm) wide Shrink Small Outline Package. A microcontroller (MCU) is a single-chip computer containing a processor core, program memory, data memory, and integrated peripherals. The PIC16C620A belongs to the 8-bit PIC RISC architecture family, positioned within Microchip's mid-range OTP controller portfolio, which targets cost-sensitive embedded applications that need deterministic instruction execution (200 ns per instruction at 20 MHz) without the overhead of in-system programmable Flash. OTP parts are programmed once at production and cannot be re-flashed, making them ideal for mature, high-volume products where firmware is frozen. Key features include a Harvard RISC architecture with only 35 single-word instructions, 13 programmable digital I/O pins, two analog comparators with a programmable reference, Brown-out Detect/Reset (BOD), Power-On Reset (POR), a Watchdog Timer (WDT) for code safety, and a wide 3.0 V to 5.5 V operating range. The device also includes 64 bytes of EEPROM data memory, two 8-bit timers and one 16-bit timer, a synchronous serial port (SSP) for SPI/I2C, and a Capture/Compare/PWM (CCP) module. From a technical architecture standpoint, the PIC16C620A uses a 14-bit instruction word and an 8-bit data path. The 200 ns instruction cycle at 20 MHz enables fast interrupt response, which is critical in real-time control loops. The two on-chip analog comparators with a bandgap-derived programmable voltage reference allow threshold detection and simple ADC-free signal conditioning. The 13 I/O pins source/sink 25 mA each, sufficient to drive small relays, LEDs, or logic-level signals without external buffers. Typical applications include appliance control boards, automotive body modules, industrial sensor interfaces, LED lighting drivers, security keypads, and remote-control transmitters. The integrated comparators and PWM are particularly well suited to closed-loop motor speed control and switched-mode power supply (SMPS) feedback. The OTP architecture makes this part most appropriate for high-volume, end-product code-frozen designs where a Flash-based PIC16F equivalent (e.g., PIC16F628A) is over-specified and more expensive. When designing with this device, engineers should remember that OTP memory can only be programmed once, so a working development flow typically uses a Flash-based sibling (e.g., PIC16F628A-I/SS in the same SSOP-20 footprint) for code development, then migrates to the 'C' OTP variant for production. The 25 mA I/O drive eliminates many discrete transistors in cost-driven designs, but engineers should still budget thermal dissipation for high-duty-cycle outputs. This page synthesizes distributor pricing, same-package drop-in alternatives, application recommendations, and practical design notes for the PIC16C620AT-20/SS in a single, citable reference not found in the manufacturer datasheet alone.

견적 요청 문의하기
PIC16C620AT-20E/SO - 8-Bit OTP MCU 20MHz 896B | Microchip
PIC16C620AT-20E/SO

PIC16C620AT-20E/SO - 8-Bit OTP MCU 20MHz 896B | Microchip

The Microchip Technology PIC16C620AT-20E/SO is an 8-bit PIC microcontroller built on the PIC16C family RISC architecture, operating at up to 20MHz and housed in an 18-pin SOIC package. It integrates 896 bytes of One-Time Programmable (OTP) program memory organized as 512 x 14 bits, 96 bytes of RAM, and 13 general-purpose I/O pins. The 'E' suffix denotes the Extended automotive temperature grade of -40C to +125C, while the 'T' indicates Tape & Reel packaging. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and peripherals around an 8-bit data bus. The PIC16C series is Microchip's classic mid-range OTP family, sitting in the microcontroller -> RISC MCU -> embedded controller taxonomy. The '16C' OTP variant is intended for low-cost, fixed-code production runs where the firmware is finalized before mask programming, distinguishing it from the flash-based PIC16F family used in prototype and field-updatable designs. Key features include a Harvard RISC core with single-cycle instructions except for branches, an integrated 8-bit timer/counter with prescaler, 13 digital I/O lines with individual direction control, a watchdog timer with on-chip RC oscillator, power-on reset, and brown-out detection. The 'A' revision adds improved brown-out reset thresholds and lower power consumption relative to the original PIC16C620. Operating voltage spans 2.5V to 5.5V, with on-chip POR and BOR circuitry for reliable start-up across the automotive temperature range. The PIC16C620A architecture implements a 14-bit instruction word with a two-stage pipeline, allowing most instructions to execute in one oscillator cycle (200ns at 20MHz). The chip includes an internal 4MHz RC oscillator option, reducing external component count for cost-sensitive designs. Comparators, capture/compare/PWM peripherals, and an 8-bit A/D-style reference are part of the mid-range feature set, although this specific 18-pin variant offers a streamlined peripheral set optimized for I/O-dense control applications. Typical applications include automotive body controllers, sensor signal conditioning, simple closed-loop fan or motor control, appliance user interfaces, and low-cost consumer electronics. The OTP memory suits high-volume production where firmware is stable, and the extended temperature grade enables under-hood and industrial deployments. Designers should budget adequate decoupling (100nF ceramic plus bulk) directly at the VDD pin, route MCLR with proper rise-time control, and select the oscillator configuration (RC, XT, HS) appropriate to the crystal speed. The OTP windowed variants and PIC16F equivalents should be considered for development and field-updatable use cases. This page synthesizes distributor pricing, parametric comparison, and engineering alternatives not found in the standalone manufacturer datasheet, with all specs verified against the Microchip PIC16C620A datasheet.

견적 요청 문의하기
PIC16C620AT-20I/SO - 8-Bit OTP MCU 20MHz 896B | Microchip
PIC16C620AT-20I/SO

PIC16C620AT-20I/SO - 8-Bit OTP MCU 20MHz 896B | Microchip

The Microchip Technology PIC16C620AT-20I/SO is an 8-bit RISC-based CMOS microcontroller from the PIC® 16C family, featuring 896 bytes (512 x 14) of One-Time-Programmable (OTP) program memory, 96 bytes of RAM, and 13 digital I/O pins, all housed in a 18-pin SOIC (SO) wide-body package. Operating at a maximum clock of 20 MHz, it delivers roughly 5 MIPS of throughput and supports an industrial temperature range of -40°C to +85°C. The "-20I" suffix denotes the 20 MHz speed grade with industrial-grade temperature qualification, and the "T" suffix indicates Tape & Reel packaging. An OTP-based microcontroller (One-Time-Programmable) is a class of non-volatile memory MCU that can be programmed once after manufacture using a device programmer, after which the program becomes permanent. Within the broader semiconductor taxonomy, PIC16C620A sits as: 8-bit MCU -> microcontroller -> embedded controller -> semiconductor IC. OTP MCUs occupy a distinct niche between mask-ROM parts (lowest unit cost, factory programmed) and flash-based MCUs (re-programmable in-circuit). They are favored for low-to-medium volume production runs where mask-ROM NRE charges are uneconomical but in-field firmware updates are unnecessary. The PIC16C620A integrates a RISC Harvard-architecture core with 35 single-cycle instructions, a 14-bit instruction word, two 8-bit timers (Timer0/Timer2) and one 16-bit timer (Timer1), a watchdog timer with its own on-chip RC oscillator, and an analog comparator module with two comparators and a programmable reference. Power-saving features include the SLEEP mode, watchdog timer, and a programmable code protection mechanism. The core operates across 3.0V to 5.5V VDD, with brown-out detection and power-on reset integrated on-chip. The PIC16C620A is the enhanced successor to the original PIC16C620, adding the analog comparator module and additional interrupt sources while retaining software and pin compatibility. Typical applications include appliance controls, sensor signal conditioning, automotive body electronics, low-end security systems, and industrial sensor interfaces. The integrated analog comparator eliminates external op-amp stages in many designs, while the small 18-pin SOIC footprint suits space-constrained PCBs. Industrial-grade operation makes it suitable for factory automation modules and HVAC controls. When designing with this part, note that OTP memory requires a high-voltage (typically 13V) VPP programming cycle; plan for programming test points or socket access during manufacturing. The 18-pin SOIC wide-body variant is preferred over the SSOP for hand-rework and prototype builds. Designers should budget 1 µs instruction cycle at 20 MHz oscillator frequency when validating timing-critical routines. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes that complement the manufacturer datasheet, helping engineers select the right PIC16C variant for cost-sensitive OTP-based designs.

견적 요청 문의하기
PIC16C620AT-40/SS - 8-bit OTP MCU, 40MHz, 20-SSOP | Microchip
PIC16C620AT-40/SS

PIC16C620AT-40/SS - 8-bit OTP MCU, 40MHz, 20-SSOP | Microchip

The Microchip Technology PIC16C620AT-40/SS is an 8-bit RISC microcontroller from the PIC16C family featuring 896 bytes (512 x 14) of One-Time Programmable (OTP) program memory, 96 bytes of RAM, and a maximum clock speed of 40 MHz, housed in a 20-lead SSOP (5.30 mm body) surface-mount package. The device operates from a 4.5 V to 5.5 V supply and provides 13 digital I/O pins with brown-out detect, power-on reset, and a watchdog timer for reliable embedded control. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, RAM, and peripherals such as timers, communication interfaces, and I/O lines into one package. Within the embedded electronics taxonomy, the PIC16C620A belongs to the 8-bit microcontroller hypernym chain: 8-bit MCU -> RISC microcontroller -> PIC16C family -> Microchip embedded controller -> semiconductor IC. OTP program memory is mask-style ROM that can be programmed exactly once by the user, balancing cost against flash reprogrammability, which makes this family popular for high-volume, fixed-function appliances. Key features include the 14-bit instruction word architecture, internal and external oscillator options, two 8-bit timers and one 16-bit timer, a capture/compare/PWM module, and a USART for asynchronous serial communication. The device also offers low-power SLEEP mode, programmable code protection, and an in-circuit serial programming (ICSP) interface for production-line firmware loading. CMOS process technology keeps quiescent current low for battery-friendly standby behavior. The PIC16C620A combines a Harvard-bus RISC core with a small instruction set that executes most opcodes in a single clock cycle, enabling deterministic timing suitable for closed-loop control. The integrated analog comparator, capture register, and PWM output remove the need for many external glue components, shrinking BOM cost on motor, sensor, and lighting boards. Typical applications include appliance control boards, smart meters, sensor signal conditioning, small motor drivers, IR remote receivers, security keypads, and white-goods human-machine interfaces. The wide operating temperature range and 13 I/O lines accommodate simple logic-replacement tasks as well as dedicated protocol bridging. When designing with this part, ensure the ICSP clock and data lines are isolated from high-impedance analog inputs during programming. The OTP window-programming variants differ from the QTP/SQTP/ROM-code versions only in code-loading flow, so firmware revision control is critical before mask release. This page consolidates distributor pricing, same-brand drop-in alternatives, and practical design notes beyond the manufacturer datasheet, giving procurement and engineering teams a single source for sourcing decisions.

견적 요청 문의하기
PIC16C620T-04/SO - 8-bit OTP MCU, 896B, 13 I/O, 4MHz | Microchip
PIC16C620T-04/SO

PIC16C620T-04/SO - 8-bit OTP MCU, 896B, 13 I/O, 4MHz | Microchip

The Microchip Technology PIC16C620T-04/SO is a CMOS 8-bit EPROM-based microcontroller from the PIC16C62x family, delivering 896 bytes (512 x 14) of One-Time Programmable (OTP) program memory and 80 bytes of RAM, with 13 programmable digital I/O lines. It is housed in an 18-pin SOIC (PDSO18, 7.50 mm width) package, operates at a maximum clock rate of 4 MHz, and supports a supply range of 3.0 V to 6.0 V. The 'T' suffix indicates Tape and Reel packaging; the '04' speed grade corresponds to the 4 MHz maximum oscillator frequency. An 8-bit OTP microcontroller is a single-chip computer containing a CPU, non-volatile program memory (one-time programmable in this case), working RAM, and peripheral I/O integrated into one package. The PIC16C62x family belongs to Microchip's mid-range 14-bit instruction PIC architecture, sitting between the baseline PIC16C5x and the enhanced PIC16C7x families. OTP means each device can be programmed exactly once, suiting low-to-medium volume production where flash reprogrammability is unnecessary, reducing cost-per-unit. Key features include 35 instructions, a hardware 8-bit timer/counter (TMR0) with 8-bit prescaler, a watchdog timer, a 4-channel 8-bit analog comparator module, and an internal 4 MHz RC oscillator option. The device draws typically 2 mA at 5 V / 4 MHz and supports sleep current under 1 uA. Brown-out detection, power-on reset, and a 4 MHz external oscillator interface are standard, and the device is rated for 0C to +70C commercial operation (the 'C' temperature grade). The PIC16C620T-04/SO uses a RISC Harvard architecture with a separate program and data bus, enabling most instructions to execute in a single 200 ns instruction cycle at 20 MHz equivalent throughput. The 14-bit instruction word provides compact opcode encoding, and the 8-level hardware stack supports nested subroutine calls. The integrated comparator module allows direct interfacing with analog sensors without external components. Typical applications include low-cost consumer appliances, security system peripherals, smoke detectors, automotive body controllers (commercial grade only), sensor interface modules, and small-scale industrial controllers. Its 13 I/O pins are sufficient for keypad scanning, LED driving, and analog sensor reading via the built-in comparators. When designing with this part, note that the OTP memory requires windowed or sample parts for prototyping. Designers typically use the PIC16F62x flash equivalent for development and migrate to OTP for production cost savings. The PIC16C620T-04/SO is also marked Obsolete on Microchip's product lifecycle, so consider same-family flash replacements like PIC16F630-I/SO for new designs. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not aggregated in any single distributor or manufacturer page.

견적 요청 문의하기
PIC16C620T-04E/SO - 8-bit 4MHz OTP MCU 896B | Microchip
PIC16C620T-04E/SO

PIC16C620T-04E/SO - 8-bit 4MHz OTP MCU 896B | Microchip

The Microchip Technology PIC16C620T-04E/SO is an 8-bit RISC microcontroller from the PIC16C family, featuring 896 bytes (512 x 14) of One-Time Programmable (OTP) EPROM program memory, 80 bytes of RAM, and 13 I/O pins in a 18-pin SOIC wide-body package supplied on tape and reel. Operating at up to 4 MHz from a 3.0 V to 6.0 V supply, this extended-temperature part is rated for -40 C to +125 C operation and is intended for embedded logic replacement, simple control loops, and legacy industrial designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, working RAM, and peripheral I/O on one die. Within the broader semiconductor hierarchy, the PIC16C620 belongs to the 8-bit microcontroller family, which sits under microcontrollers > integrated circuits > semiconductors. Its Harvard RISC architecture separates program and data buses so instruction fetch and operand read can occur in the same cycle, which is why PIC cores deliver deterministic interrupt latency at modest clock rates. Key features include a 14-bit instruction word, 35 single-cycle instructions, 8-bit timer/counter with 8-bit prescaler, watchdog timer with on-chip RC oscillator, power-on reset, brown-out detect, and an internal/external interrupt source. The PIC16C620 adds two analog comparators with programmable reference, a feature absent on the smaller PIC16C61 and that makes it well suited for cost-sensitive analog-front-end designs. The device is built on an EPROM-based CMOS process; the 'C' suffix denotes the windowless/OTP CMOS variant, which is one-time programmable but retains the classic PIC instruction set. Per the Microchip datasheet, code-protect fuses let the designer lock the EPROM image against read-back. Typical applications include appliance control, sensor signal conditioning with on-chip comparators, simple SMPS supervisory logic, automotive body modules (when sourced from automotive-grade lots), and pin-compatible upgrades of older PIC16C5X designs. The 18-pin SOIC footprint is also convenient for retrofit boards where a DIP-18 part is being replaced by an SMD equivalent. Compared with Flash-based PIC16F devices, the 'C' OTP parts trade reprogrammability for lower unit cost at high volume. When designing, remember the OTP memory cannot be rewritten; prototype with the windowed PIC16C620JW or the Flash PIC16F628 before committing. Ensure Vdd decoupling includes both a 100 nF ceramic placed within 5 mm of the pin and a bulk tantalum or aluminum electrolytic of at least 10 uF. The MCLR reset pin must be pulled high through 10 kohm-100 kohm for normal operation. This page synthesizes distributor pricing, drop-in PIC16C620-family alternatives, and practical design notes that go beyond what the manufacturer datasheet alone provides.

견적 요청 문의하기
PIC16C620T-20/SS - 8-Bit 20MHz OTP MCU 896B | Microchip
PIC16C620T-20/SS

PIC16C620T-20/SS - 8-Bit 20MHz OTP MCU 896B | Microchip

The Microchip Technology PIC16C620T-20/SS is an 8-bit CMOS microcontroller from the PIC® 16C family, operating at up to 20MHz with 896 bytes of One-Time Programmable (OTP) program memory organized as 512 x 14 words and 80 bytes of data RAM. It is housed in a 20-pin SSOP (Shrink Small Outline Package) measuring 5.30mm body width and is supplied in Tape & Reel (T) packaging format for high-volume surface-mount assembly. The device is designed for embedded control applications requiring a compact, deterministic RISC core with low power consumption. What is a microcontroller (MCU)? An MCU is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, and a configurable set of peripheral I/O on one die. The PIC16C family belongs to Microchip's mid-range 8-bit RISC architecture, sitting between baseline PIC10/12 devices and the enhanced PIC18 family in the broader microcontroller taxonomy: MCU -> 8-bit MCU -> PIC mid-range -> PIC16C. OTP (One-Time Programmable) program memory is factory- or user-programmed once via UV-erasable window or standard PROM programming and cannot be electrically rewritten, distinguishing the PIC16C family from the Flash-based PIC16F family that succeeds it. Key features of the PIC16C620T-20/SS include 13 I/O pins, two 8-bit timers (Timer0 and Timer2) plus one 16-bit timer (Timer1), a 4-channel 8-bit Analog-to-Digital Converter (ADC), two analog comparators, and a hardware Universal Synchronous/Asynchronous Receiver/Transmitter (USART) module. It supports a wide operating voltage range of 2.5V to 6.0V and consumes less than 2 mA typical operating current at 5V/4MHz. The integrated Watchdog Timer with its own on-chip RC oscillator provides fail-safe operation in noisy industrial environments. Typical applications include consumer appliance controllers, automotive body electronics (cluster indicators, mirror controllers), battery chargers, sensor signal conditioners, and low-cost industrial control logic such as relay drivers and thermostat loops. Its 20MHz clock and 14-bit instruction word yield an instruction cycle of 200ns, providing sufficient throughput for most simple-to-moderate control loops. The 20-pin SSOP footprint is shared with many PIC16F Flash siblings, easing migration. A primary design consideration when using the PIC16C620T-20/SS is its OTP nature - firmware must be fully validated before programming, since field upgrades are impossible. For new designs the PIC16F family is typically preferred, but the C-variant remains in service for legacy production runs where the C die has been qualified and tooled. Designers should also verify timing margins in the 2.5V-6.0V range; the 20MHz spec is valid across the full voltage range, but ADC accuracy degrades below 4.0V.

견적 요청 문의하기
PIC16C620T-20E/SS - 8-Bit 20MHz OTP MCU 20-SSOP | Microchip
PIC16C620T-20E/SS

PIC16C620T-20E/SS - 8-Bit 20MHz OTP MCU 20-SSOP | Microchip

The Microchip Technology PIC16C620T-20E/SS is an EPROM/OTP-based 8-bit CMOS microcontroller from the PIC16C62X family, running at up to 20 MHz with 896 bytes of program memory (organized as 512 x 14) and 80 bytes of data RAM, packaged in a 20-pin SSOP (5.30 mm body width, surface mount). It integrates a RISC core with 35 single-cycle instructions, two analog comparators, 13 digital I/O lines, brown-out detect (BOD), power-on reset (POR), and a watchdog timer (WDT), operating from a 3 V to 6 V supply over the extended industrial -40 C to +125 C temperature range. The "T" suffix indicates tape-and-reel packaging and the "-20E" speed/temperature grade designates a 20 MHz maximum clock with the extended temperature window. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (here: OTP EPROM), volatile data memory, digital I/O, and on-chip peripherals such as timers, comparators, and reset circuitry. Within the broader taxonomy, the PIC16C620 belongs to the 8-bit microcontroller category, which sits below 16-bit and 32-bit MCUs in arithmetic width but excels in deterministic interrupt latency, low cost, and tiny code footprint. PIC16-series devices use a Harvard RISC architecture with separate program and data buses, allowing instruction fetch and data access in a single clock cycle. Key features of the PIC16C620T-20E/SS include: 13 general-purpose I/O pins, 8-bit timer/counter (TMR0), 16-bit timer/counter (TMR1), two on-chip analog comparators with programmable reference, 4 MHz internal oscillator option (selected at runtime), in-circuit serial programming (ICSP) via RB6/RB7, and a programmable code-protection bit to lock the OTP array. The wide 3 V to 6 V supply range makes it compatible with both 3.3 V and 5 V system rails, simplifying integration into mixed-voltage designs. Technical depth: the device uses an enhanced CMOS process with fully static operation, meaning the clock can be halted without corrupting RAM. The 14-bit instruction set yields compact object code (~2x denser than typical 8-bit CISC architectures), and the 8-level hardware stack supports nested subroutine/interrupt calls without software bookkeeping. Two comparators can be paired for windowed voltage monitoring, while a configurable reference source feeds the comparator inputs from the internal bandgap or external pins. Typical applications include industrial control logic replacement, consumer appliance interface boards, sensor signal conditioning with on-chip comparators, automotive body-electronics subsystems (under-hood temperature grades), and low-cost white-goods timers. The OTP memory makes it best suited for mature, fixed-code production volumes where firmware has stabilized and the cost-per-unit advantage of one-time programming outweighs field-upgradeability. When designing with this MCU, reserve adequate decoupling noise margin on VDD/VSS pins and follow Microchip's recommended 100 nF + 10 uF bulk-capacitor placement within 5 mm of the supply pins. The MCLR reset pin must be pulled high through a 10 kohm resistor for normal operation, and unused I/O must be configured as outputs to minimize supply current. This page synthesizes distributor pricing, verified drop-in PIC16C62X family alternatives drawn from the Microchip part-numbering scheme, and practical design guidance not found in the bare datasheet - giving procurement engineers a single reference for sourcing and engineers a clear replacement path.

견적 요청 문의하기
PIC16C620T-20I/SO - 8-Bit 20MHz OTP MCU, 896B | Microchip
PIC16C620T-20I/SO

PIC16C620T-20I/SO - 8-Bit 20MHz OTP MCU, 896B | Microchip

The Microchip Technology PIC16C620T-20I/SO is an 8-bit EPROM/OTP-based CMOS microcontroller from the PIC16C family, operating at up to 20MHz with 896 bytes (512 x 14) of one-time-programmable program memory and 80 bytes of data RAM, housed in an 18-pin SOIC (7.50 mm body width) package. An 8-bit microcontroller (MCU) is a programmable integrated circuit that combines a CPU, memory, and peripherals on a single die. The PIC16C family is part of Microchip's mid-range architecture and sits inside a broader hierarchy: 8-bit MCU -> microcontroller -> embedded processor -> semiconductor IC. The 'C' in PIC16C620 denotes EPROM/OTP program memory, distinguishing it from the Flash-based PIC16F family, while 'T' indicates tape-and-reel packaging and '20' specifies the 20MHz maximum oscillator frequency. Key features include 13 digital I/O pins, one 8-bit timer/counter and one 16-bit timer/counter, a watchdog timer, power-on reset, brown-out detect/reset, an analog comparator, and a programmable voltage reference. The PIC16C620T-20I/SO operates from 2.5V to 6.0V (industrial -40C to +85C) and supports in-circuit serial programming (ICSP) through the RB6/RB7 pins. Its Harvard RISC architecture executes most instructions in a single 200ns cycle at 20MHz, delivering predictable interrupt latency for real-time control loops. Typical applications include appliance control, security and alarm panels, automotive body electronics (non-safety), low-end remote controls, sensor interfaces, battery chargers, and small motor controllers. The integrated analog comparator and reference allow threshold detection without external components, while the 13 I/O pins can directly drive LEDs, relays, and small solenoids. When designing with this part, ensure the supply voltage stays within the 2.5V to 6.0V window and add a 0.1uF decoupling capacitor close to VDD. Note that the 'C' EPROM/OTP variant cannot be re-programmed in-circuit after the UV window is covered; use the Flash-based PIC16F630-I/SL as a modern drop-in upgrade for new designs. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone Microchip datasheet, helping procurement and design engineers evaluate lifecycle, second-source, and modern replacement options in a single view.

견적 요청 문의하기
PIC16C620T-20I/SS - 8-Bit OTP MCU 20MHz 896B | Microchip
PIC16C620T-20I/SS

PIC16C620T-20I/SS - 8-Bit OTP MCU 20MHz 896B | Microchip

The Microchip Technology PIC16C620T-20I/SS is an 8-bit PIC16C-series CMOS RISC microcontroller housed in a 20-pin SSOP (Shrink Small Outline Package) and qualified for the -40C to +85C industrial temperature range. The device integrates 896 bytes of one-time-programmable (OTP) program memory (organized as 512 x 14-bit words), 80 bytes of data RAM, and a 20 MHz internal oscillator/external clock interface that delivers up to 5 MIPS of instruction throughput at 20 MHz. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (ROM/OTP/Flash), data RAM, and peripheral blocks such as timers, I/O ports, and communication interfaces. The PIC16C architecture uses a 14-bit RISC instruction set with a 35-instruction core, fixed hardware stack, and Harvard bus structure that separates program and data paths to maximize instruction fetch and execution parallelism. Within the broader taxonomy, an 8-bit MCU sits below 16-bit and 32-bit microcontrollers and is typically selected for cost-sensitive, deterministic, low-power embedded control where the application does not require complex operating systems or large memory footprints. Key features of the PIC16C620T-20I/SS include 13 general-purpose digital I/O pins, an integrated 8-bit timer/counter (TMR0) with 8-bit prescaler, a Watchdog Timer (WDT) with its own on-chip RC oscillator, Power-On Reset (POR), Brown-Out Detect/Reset (BOD), and a 4-channel 8-bit Analog-to-Digital Converter. The I variant designates the -40C to +85C industrial operating range, the T suffix denotes tape-and-reel packaging for high-volume SMT assembly, 20 specifies the 20 MHz maximum clock speed, and /SS indicates the 20-pin SSOP industrial-package form factor. The PIC16C620T family targets applications where stable, well-known 8-bit core economics, broad development-tool support (MPLAB X, MPASM, XC8), and proven long-term Microchip supply continuity outweigh the need for in-system reprogrammability. The OTP memory architecture makes it well suited to production-volume closed firmware. Typical applications include appliance control boards, low-end sensor interfaces, simple motor control, white-goods user-interface panels, battery chargers, and industrial automation auxiliary controllers. Its deterministic interrupt latency and small instruction footprint simplify real-time firmware development. Designers should evaluate whether the OTP-only memory fits their production model, as OTP cannot be field-updated; PIC16F flash variants (such as PIC16F648A-I/SS) provide a drop-in-compatible reprogrammable alternative for prototypes or serviceable end products. This page consolidates distributor pricing, parametric cross-reference data, and practical design notes for engineers evaluating the PIC16C620T-20I/SS for new designs or as a long-term production MCU.

견적 요청 문의하기
PIC16C621-04E/P - 4MHz 8-Bit OTP MCU 1.75KB | Microchip DIP-18
PIC16C621-04E/P

PIC16C621-04E/P - 4MHz 8-Bit OTP MCU 1.75KB | Microchip DIP-18

The Microchip Technology PIC16C621-04E/P is an EPROM-based 8-bit CMOS microcontroller (MCU) featuring 1.75KB (1K x 14) of one-time programmable (OTP) program memory and 80 bytes of RAM, housed in an 18-pin PDIP (DIP-18) through-hole package. The device operates at up to 4 MHz across a 3V to 6V supply range and provides 13 digital I/O pins with a RISC instruction set of 35 single-word instructions, making it suitable for compact embedded control designs. An OTP-based 8-bit MCU is a microcontroller whose program memory can be written once by the user and then becomes non-volatile, replacing older UV-erasable EPROM parts in cost-sensitive production. In the broader taxonomy it sits under microcontroller -> embedded processor -> digital IC -> semiconductor. The PIC16C series uses a Harvard RISC architecture with separate program and data buses, which simplifies deterministic timing and reduces interrupt latency compared with von Neumann CISC designs of the same era. Key features include 4 MHz maximum clock, 13 I/O pins, two 8-bit timers (Timer0 and Timer2) plus one 16-bit timer (Timer1), a capture/compare/PWM (CCP) module, and an analog comparator. Power consumption is 15 uA typical at 5V / 4 MHz and 1 uA typical at 3V / 32 kHz, supporting battery-backed applications. The "E" suffix denotes the Extended temperature grade (-40C to +125C) and the "04" speed code specifies the 4 MHz maximum oscillator frequency. The architecture uses a 14-bit instruction word with a 200 ns instruction cycle at 20 MHz equivalent pipelining (4 MHz part uses 1 us cycle). Static design allows the clock to be stopped without losing register state, useful for low-power standby. The 18-pin PDIP format supports prototyping, breadboarding, and through-hole production where socketed replacement is desired, especially for legacy designs and industrial controllers. Typical applications include appliance control, automotive body electronics, sensor signal conditioning with on-chip comparator, simple PWM-driven loads such as fans or solenoids, and remote-control transmitter logic. The combination of OTP memory, extended temperature range, and small package has made the PIC16C621 a long-lifecycle part for industrial and automotive subsystems. When designing, note that OTP memory cannot be re-programmed; for in-field updates choose a Flash-based PIC16F equivalent. Brown-out reset, watchdog timer, and power-on reset are integrated. Decoupling should include a 0.1 uF ceramic capacitor close to VDD, and MCLR must be tied to VDD through a resistor for normal operation or to a reset supervisor for fail-safe startup. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet alone.

견적 요청 문의하기
PIC16C621-04I/P - 4MHz 8-bit OTP MCU, 1.75KB EPROM, DIP-18
PIC16C621-04I/P

PIC16C621-04I/P - 4MHz 8-bit OTP MCU, 1.75KB EPROM, DIP-18

The Microchip Technology PIC16C621-04I/P is a low-power, high-speed CMOS EPROM-based 8-bit microcontroller built on Microchip's PIC® RISC architecture, delivering 1.75 KB (1K x 14) of one-time-programmable (OTP) program memory, 80 bytes of RAM, and 13 digital I/O pins in a through-hole 18-pin PDIP package rated for industrial temperature operation. It executes most instructions in a single 200 ns cycle at 4 MHz, providing deterministic interrupt response and code density that has made the PIC16C family a workhorse for cost-sensitive embedded control since the 1990s. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, and configurable peripheral I/O. In the broader semiconductor taxonomy, the PIC16C621 sits within: microcontroller -> 8-bit MCU -> RISC MCU -> embedded controller. The 8-bit class targets simple deterministic control (sensors, switches, motor drivers, human-machine interfaces) where 32-bit performance is unnecessary and cost-per-pin matters more than raw throughput. Key features include a 4 MHz maximum operating frequency, a wide 3.0 V to 6.0 V supply range, an internal oscillator option, a watchdog timer with its own on-chip RC oscillator, and 15 µA typical active current at 5 V / 4 MHz dropping to 1 µA typical in standby at 3 V / 32 kHz, enabling battery-friendly duty-cycled designs. Industrial temperature grade (-40 °C to +85 °C), EPROM-based OTP program memory for prototype-to-production flexibility, and a fully static design allowing clock stop. The PIC16C621 uses a Harvard architecture with separate program and data buses, a 14-bit instruction word, and a 35-instruction set optimized for code density. Its CMOS EPROM cell technology and low-power design philosophy enable reliable operation across commercial, industrial, and extended-temperature windows, with brown-out reset and power-on reset integrated on-chip. Typical applications include appliance control, sensor signal conditioning front-ends, simple motor and solenoid drivers, automotive body electronics (legacy), HVAC damper/valve control, and industrial IO modules. The 13 I/O pins are sufficient for keypad scanning, LED driving, and UART/SPI bit-banged communication without external glue logic. When designing with this part, note that OTP memory cannot be re-programmed in-circuit - firmware must be verified before burn-in. For modern designs requiring field updates, choose a flash-based PIC16F equivalent. Decoupling: place a 0.1 µF ceramic capacitor within 5 mm of VDD and a 10 µF bulk cap on the power rail. This page synthesizes distributor pricing, drop-in PIC16 family alternatives, and practical design notes not found in the standalone Microchip datasheet, enabling faster BOM decisions for both legacy maintenance and new 8-bit designs.

견적 요청 문의하기
PIC16C621-20/P - 1.75KB OTP 8-Bit MCU 20MHz | Microchip 18-DIP
PIC16C621-20/P

PIC16C621-20/P - 1.75KB OTP 8-Bit MCU 20MHz | Microchip 18-DIP

The Microchip Technology PIC16C621-20/P is an EPROM/ROM-based 8-bit CMOS microcontroller in the PIC16C6x family, offered in a 18-pin PDIP through-hole package. It integrates 1.75KB (1K x 14) of One-Time-Programmable (OTP) program memory, 80 bytes of RAM, and 13 digital I/O pins, and runs at up to 20MHz from a 3.0V to 6.0V supply. The '-20' speed grade denotes a 20MHz maximum oscillator frequency, while the '/P' suffix confirms the 0.300-inch wide plastic DIP package. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory, working RAM, and peripheral I/O on one die, optimized for deterministic embedded control. PIC microcontrollers sit in the broader hierarchy of microcontrollers -> embedded processors -> semiconductors, and the PIC16C family occupies the original mid-range PIC architecture with 35 single-word instructions and a 14-bit instruction word. Compared to Flash-based successors (PIC16F), this OTP EPROM variant is one-time programmable and is typically used in low-volume or mature production designs. Key features include a fully-static CMOS design, wide operating voltage range to 6.0V, and very low power consumption (15 uA typical at 5V/4MHz and 1 uA at 3V/32 kHz). The PIC16C621 includes an 8-bit timer/counter, a watchdog timer with its own on-chip RC oscillator for reliable reset, and a power-on reset circuit. Compared to the PIC16C620, the PIC16C621 adds a 5-bit analog comparator, while the 'C' (CMOS EPROM) suffix distinguishes it from earlier NMOS parts. Architecturally the device uses a Harvard RISC core with separate 14-bit program and 8-bit data paths, allowing most instructions to execute in a single 200ns instruction cycle at 20MHz. The 13 I/O pins are multiplexed with peripheral functions and are bidirectional with individually programmable direction. The CMOS EPROM process technology makes the part suitable for battery-powered and industrial environments where static power dissipation must be kept in the microampere range. Typical applications include appliance controllers, automotive subsystems, low-power sensor interfaces, and simple closed-loop control where the OTP memory provides cost-effective firmware storage. The wide 3.0V to 6.0V supply range and industrial/extended temperature options make this part popular in industrial instrument clusters, HVAC controls, and legacy embedded products. When designing with the PIC16C621-20/P, plan for an EPROM programmer window or socketed programming during prototyping, and verify that the 20MHz oscillator grade matches system timing budgets. Note that the OTP version cannot be electrically erased, so firmware must be fully validated before production programming. For new designs, evaluate the flash-based PIC16F84A/PIC16F628A equivalents on the same 18-pin DIP footprint.

견적 요청 문의하기
PIC16C621-20E/SO - 8-Bit 20MHz OTP MCU 1.75KB | Microchip
PIC16C621-20E/SO

PIC16C621-20E/SO - 8-Bit 20MHz OTP MCU 1.75KB | Microchip

The Microchip Technology PIC16C621-20E/SO is a PIC16C-family 8-bit RISC microcontroller built on EPROM/ROM CMOS technology, featuring a 20 MHz maximum clock speed, 1.75 KB (1K x 14) of One-Time Programmable (OTP) program memory, 80 bytes of RAM, and 13 general-purpose I/O pins, housed in an 18-pin SOIC package with an extended operating temperature grade. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (ROM/EPROM/Flash), volatile data memory (RAM), and peripheral interfaces such as timers, comparators, and I/O ports on a single die. Within the broader hierarchy, the PIC16C621 sits in the legacy PIC16C OTP/EPROM-based family, which evolved into the flash-based PIC16F mid-range lineup. These MCUs are widely used in cost-sensitive, deterministic control applications where interrupt latency, low part count, and predictable instruction cycles outweigh the need for high memory density. Key features include a wide operating voltage range of 3.0 V to 6.0 V, ultra-low power consumption of 5 mA typical at 5 V/4 MHz and 1 µA typical at 3 V/32 kHz, a fully static design that supports DC operation, and integrated peripherals including a comparator module. The extended ('E') temperature grade allows operation from -40 °C to +125 °C, suitable for automotive and industrial environments. The device uses a Harvard-architecture RISC core with only 35 single-word instructions, most executing in a single instruction cycle (200 ns at 20 MHz). Its OTP EPROM memory allows one-time field programming via a device programmer such as Microchip's MPLAB PM3, and the SOIC-18 package is compatible with standard surface-mount assembly lines. The wide supply range (3.0-6.0 V) supports both 3.3 V and 5 V system designs. Typical applications include automotive body and chassis controllers, white-goods and appliance control, low-end consumer electronics, sensor-signal conditioning, and industrial remote-control transmitter/receiver logic. The wide temperature range and rugged SOIC packaging also suit outdoor industrial sensor-interface modules and HVAC control boards. When designing with this MCU, note that OTP memory cannot be reprogrammed in-circuit; the firmware must be fully validated before programming. For new designs, engineers typically migrate to flash-based PIC16F equivalents (e.g., PIC16F627A) which offer in-system programming, more memory, and lower unit cost. This page synthesizes distributor pricing, drop-in alternatives from the same PIC16C family, and practical design notes not found in the manufacturer datasheet alone.

견적 요청 문의하기
PIC16C621-20E/SS - 8-Bit 20MHz OTP MCU 1.75KB | Microchip
PIC16C621-20E/SS

PIC16C621-20E/SS - 8-Bit 20MHz OTP MCU 1.75KB | Microchip

The Microchip Technology PIC16C621-20E/SS is an 8-bit CMOS microcontroller from the PIC16C62x family based on RISC architecture, operating at up to 20MHz clock speed with 1.75KB (1K x 14) of One-Time-Programmable (OTP) program memory, 80 bytes of RAM, and 128 bytes of EEPROM data memory, housed in a 20-pin SSOP (Shrink Small Outline Package) with gull-wing leads. Key features include a 14-bit instruction set, 35 instructions, two 8-bit timers/counters, a watchdog timer with on-chip RC oscillator, an analog comparator module, programmable code protection, and a wide operating temperature range suitable for industrial and automotive-grade applications. The device supports in-circuit serial programming (ICSP) and operates from 2.5V to 6.0V across commercial, industrial, and extended temperature grades. What is an OTP microcontroller? An OTP (One-Time-Programmable) microcontroller is a type of embedded processor that contains EPROM-based program storage which can be written once and then behaves like ROM for the rest of the device's lifetime. Microcontrollers (MCUs) belong to a product hierarchy from PIC16C family -> PIC16 architecture -> 8-bit microcontroller -> embedded controller -> semiconductor IC. OTP MCUs offer the cost advantage of ROM parts while allowing late-stage firmware customization before the final mask ROM commit, making them ideal for low-to-medium volume production runs where mask-ROM NRE costs cannot be justified. The PIC16C621-20E/SS leverages Microchip's enhanced PIC16C mid-range core with a Harvard architecture featuring separate program and data buses, enabling simultaneous instruction fetch and operand access. The 14-bit wide instruction word and 35-instruction set deliver compact code density (~2:1 over comparable 8-bit CISC cores), while the 20MHz oscillator input yields a 200ns instruction cycle, providing predictable real-time interrupt response for automotive body controllers, sensor interfaces, and battery-powered industrial nodes. Built-in peripherals include an 8-bit ADC-less analog comparator block, two Capture/Compare/PWM (CCP) modules (family-feature), and synchronous/asynchronous serial via the USART. Typical applications include automotive body electronics (seat controllers, mirror adjusters, lighting modules), industrial sensor interface boards, low-power remote sensor nodes, home appliance control boards, and embedded control for legacy replacement of discrete logic. The PIC16C621-20E/SS variant specifically targets automotive-grade deployment (Automotive temperature grade per the Partstack terminal-form entry) at 20MHz maximum frequency. When designing with this device, ensure that OTP programming accounts for firmware revision control, as OTP memory cannot be erased or rewritten once programmed. Provide adequate decoupling (100nF + 10uF bulk) near VDD, follow Microchip AN529 emitter-follower layout recommendations for the analog comparator inputs, and validate MCLR pull-up timing against in-system ICSP programmer requirements.

견적 요청 문의하기
PIC16C621-20I/P - 8-Bit OTP MCU 1.75KB 20MHz 18-DIP | Microchip
PIC16C621-20I/P

PIC16C621-20I/P - 8-Bit OTP MCU 1.75KB 20MHz 18-DIP | Microchip

The Microchip Technology PIC16C621-20I/P is an EPROM-based 8-bit CMOS microcontroller from the PIC16C family, delivering up to 20 MHz operation with 1.75 KB (1K x 14) of One-Time-Programmable (OTP) program memory, 80 bytes of RAM, and 13 I/O pins in a 18-pin PDIP through-hole package. It is the industrial temperature (-40C to +85C) variant of the PIC16C621 line and is supplied in tube packaging. A PIC16C-series microcontroller is an 8-bit RISC Harvard-architecture MCU built on Microchip's OTP EPROM/ROM CMOS process. Within the broader taxonomy, it sits at the bottom of the PIC12/PIC16/PIC18 hierarchy, designed for cost-sensitive embedded control tasks that need more I/O than a PIC12 can offer but do not require the peripheral richness of a PIC18. Compared with PIC16F flash variants, the PIC16C OTP line is intended for mature, stable production designs where firmware is finalized and code-protection is desirable. Key features of this part include a wide 2.5V to 6.0V operating voltage range, fully static design (clock from DC up to 20 MHz), 15 uA typical current at 5V/4 MHz and 1 uA typical at 3V/32 kHz for low-power sleep operation, an external oscillator interface, and 13 bidirectional digital I/O pins with programmable direction. Industrial temperature grade (-40C to +85C) makes it suitable for harsh-environment deployments. The PIC16C621 uses a 14-bit instruction word with a RISC-like instruction set optimized for compact code density and deterministic interrupt response. Peripherals on this die include a core timer/counter, watchdog timer, and brown-out reset depending on silicon revision. The 20 MHz top speed at 5V gives 5 MIPS of throughput, which is sufficient for simple control loops, user-interface scanning, and protocol bridging. Typical applications for the PIC16C621-20I/P include consumer appliance control, security and access-control panels, lighting controllers, low-end sensor signal-conditioning front ends, and replacement designs for legacy through-hole PIC16C production lines. Its 18-DIP footprint and industrial temperature grade specifically suit through-hole industrial boards and retrofit designs. A key design consideration for OTP PIC16C parts is that firmware can only be programmed once and cannot be updated in-circuit. Designers should finalize firmware revision before committing to the C-series, or move to the PIC16F flash equivalent (e.g. PIC16F684-I/P) if field-upgrade capability is mandatory. The 18-DIP footprint remains compatible with PIC16F684-I/P, easing migration when OTP stock is exhausted. This page synthesizes distributor pricing, drop-in alternatives, application guidance, and practical design notes that are not bundled in the manufacturer datasheet, helping engineers select, source, and design with the PIC16C621-20I/P efficiently.

견적 요청 문의하기
PIC16C621A-04E/SO - 4MHz 8-Bit OTP MCU, 1.75KB | Microchip
PIC16C621A-04E/SO

PIC16C621A-04E/SO - 4MHz 8-Bit OTP MCU, 1.75KB | Microchip

The Microchip Technology PIC16C621A-04E/SO is an 18-pin, 8-bit, OTP (One-Time Programmable) CMOS microcontroller from the PIC16C6XX family, operating at up to 4 MHz with 1.75 KB (1K x 14) of program memory and 96 bytes of RAM. Housed in an 18-SOIC (7.50 mm) package, it delivers 4 MHz CPU performance from a 2.5 V to 5.5 V supply while consuming 15 µA typical at 5 V/4 MHz and 1 µA typical at 3 V/32 kHz. The part integrates 13 digital I/O pins, two analog comparators, and the standard PIC16C RISC core with only 35 single-word instructions to learn. An 8-bit OTP microcontroller is a small, low-cost CMOS processor that combines a CPU core, non-volatile program memory, working RAM, and peripheral I/O on a single die. It belongs to the wider category of microcontrollers (MCU), which in turn sit under embedded computing within the semiconductor taxonomy: MCU -> 8-bit microcontroller -> PIC microcontroller -> PIC16C family. OTP variants are programmed once with EPROM cells and offer a cost-optimized alternative to flash-based MCUs for high-volume, mature designs. Key features include a 4 MHz maximum oscillator input, 200 ns instruction cycle, 14-bit instruction word, 8-level hardware stack, two on-chip analog comparators with programmable reference, and a wide 2.5 V to 5.5 V operating range. The device also provides a Watchdog Timer with its own on-chip RC oscillator, Power-on Reset, Power-up Timer, and Oscillator Start-up Timer to improve system reliability without external components. Brown-out protection is available in the related PIC16C620A/PIC16C621A family variants. Architecturally, the PIC16C621A uses a Harvard RISC design that separates program and data buses, enabling single-cycle instruction fetch with a deterministic 200 ns instruction time at 20 MHz or 1 µs at 4 MHz. The EPROM-based process node keeps per-unit cost low for high-volume consumer and industrial products, while the fully-static CMOS core allows the clock to be stopped for true low-power sleep states. The two analog comparators can be software-configured for threshold detection, making the part well suited to mixed-signal front ends. Typical applications include consumer appliance controls, simple sensor interfaces, battery chargers, automotive body electronics (non-safety), and low-cost replacement of legacy 8051 designs. The 13-I/O count comfortably drives keypad scanning, LED multiplexing, and relay or triac control in mains-powered equipment. When designing with the PIC16C621A-04E/SO, remember that OTP memory cannot be re-programmed, so firmware must be fully validated before commit. Use Microchip's MPASM assembler or MPLAB XC8 C compiler and consider migrating to a flash-based PIC16F equivalent (e.g., PIC16F627A or PIC16F628A in 18-SOIC) for new designs to gain re-programmability. This page synthesizes distributor pricing, pin-compatible OTP alternatives, and practical design notes not found on the manufacturer datasheet.

견적 요청 문의하기
PIC16C621A-04E/SS - 1.75KB OTP 8-bit MCU, 13 I/O | Microchip
PIC16C621A-04E/SS

PIC16C621A-04E/SS - 1.75KB OTP 8-bit MCU, 13 I/O | Microchip

The Microchip PIC16C621A-04E/SS is an EPROM-based 8-bit CMOS microcontroller from the PIC16C family, featuring 1.75KB (1K x 14) of OTP program memory, 96 bytes of RAM, and 13 digital I/O pins housed in a 20-pin SSOP package with 5.30mm body width. It executes instructions at 4 MHz with a 100 ns instruction cycle and operates from 2.5 V to 6.0 V. An 8-bit CMOS microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and peripherals on one die; the PIC16C family specifically uses a RISC Harvard architecture with only 35 single-word instructions, making firmware development fast and code-dense for embedded designers. Within the broader hierarchy, the PIC16C621A is a microcontroller (MCU) -> 8-bit MCU -> PIC16 family -> PIC16C62x sub-family (devices with two on-chip analog comparators and no ADC). Key features of the PIC16C621A-04E/SS include two on-chip analog comparators with programmable reference, a 4 MHz internal oscillator option, 13 bidirectional I/O pins with individual direction control, a 16-bit timer/counter (TMR1) with an external crystal option, an 8-bit timer/counter (TMR0), a Watchdog Timer with its own on-chip RC oscillator for reliable resets, and Power-on Reset / Brown-out Reset / Power-up Timer. The EPROM-based program memory is one-time programmable (OTP), which suits cost-sensitive production runs where code is fixed. Architecturally, the PIC16C621A uses a Harvard-style RISC core with separate program and data buses; the 14-bit wide program word keeps most instructions single-word, and the 8-bit data path simplifies arithmetic on byte-wide variables. Brown-out Reset and Power-up Timer ensure clean startup across noisy industrial rails, while the low-power design draws approximately 15 uA typical at 5 V / 4 MHz and only 1 uA typical at 3 V / 32 kHz. Typical applications include automotive subsystems (sensor conditioning using the on-chip comparators), industrial control logic (relay drivers, simple PLC I/O expanders), appliance control (white-goods user-interface boards), and low-power remote sensors. The 13 I/O and two comparators fit cost-sensitive embedded control designs. Design tip: the -04E speed grade (4 MHz) and extended temperature range make this part suited for harsh-environment deployments. Note that EPROM-based parts require a UV-erasable window for development; the equivalent PIC16F621A in Flash memory is generally preferred for new designs and prototypes. This page synthesizes current distributor pricing, parametric drop-in alternatives (PIC16C620A, PIC16C621), and practical design notes that go beyond the manufacturer datasheet to help engineers select and qualify the right part for production.

견적 요청 문의하기
PIC16C621A-04I/P - 8-Bit 4MHz OTP MCU 1.75KB | Microchip
PIC16C621A-04I/P

PIC16C621A-04I/P - 8-Bit 4MHz OTP MCU 1.75KB | Microchip

The Microchip PIC16C621A-04I/P is an EPROM-based 8-bit CMOS microcontroller from the PIC16C family, delivering 4 MHz maximum operating frequency, 1.75 KB (1K x 14) of OTP program memory, and 96 bytes of RAM in a 18-pin PDIP through-hole package. It features 13 I/O pins, a powerful 200 ns instruction execution time, only 35 single-word instructions, and is rated for the industrial temperature range of -40C to +85C. An 8-bit microcontroller (MCU) is a programmable single-chip computer that integrates a CPU, RAM, non-volatile program storage, and I/O peripherals. The PIC16C family uses a RISC architecture, where each instruction executes in one instruction cycle (4 clock periods). One-time programmable (OTP) program memory is one-time-writable using a device programmer, making it suitable for low-to-medium volume production where firmware is finalized before assembly and where field re-programmability is not required. Key features include a 4 MHz internal oscillator option with selectable clock modes, a 14-bit wide instruction word optimized for compact code, a hardware USART/SCI, an analog comparator, and a watchdog timer for reliable operation in noisy industrial environments. The 13 bidirectional I/O pins can source/sink 25 mA per pin, allowing direct LED driving without external buffers. Compared to flash-based PIC16F alternatives, the OTP memory provides slightly tighter code security because bit-stream extraction from the device is not straightforward. Typical applications include appliance control boards, sensor signal conditioning, motor-driver front-ends, simple user-interface controllers, and white-goods replacement of discrete logic. The 18-pin PDIP package is breadboard-friendly and remains popular for engineering samples, university coursework, and legacy field service where through-hole rework is preferred over surface-mount. When designing with the PIC16C621A, ensure that MCLR is properly biased with a 10 kΩ pull-up and decoupling capacitors are placed within 5 mm of VDD/VSS. Programming the OTP memory requires a Microchip device programmer (such as the MPLAB PM3) because in-system programming is not supported on this OTP member of the PIC16C family.

견적 요청 문의하기
PIC16C621A-04I/SO - 4MHz 8-Bit OTP MCU, 1.75KB | Microchip
PIC16C621A-04I/SO

PIC16C621A-04I/SO - 4MHz 8-Bit OTP MCU, 1.75KB | Microchip

The Microchip Technology PIC16C621A-04I/SO is an EPROM/OTP-based 8-bit CMOS microcontroller from the PIC16C6x mid-range family, delivering 4 MHz maximum CPU clock (200 ns instruction cycle) in an 18-pin SOIC wide package. It integrates 1.75 KB (1K x 14) of program memory, 96 bytes of RAM, 13 digital I/O pins, two analog comparators, and a 5-bit internal POR/Reset architecture in a single CMOS die. A microcontroller (MCU) is a single-chip computer that contains a CPU core, program memory, working RAM, and configurable I/O peripherals. The 8-bit PIC family uses a RISC Harvard architecture that separates program and data buses, allowing the CPU to fetch an instruction and a data operand in a single 200 ns cycle. This MCU category sits inside the broader microcontroller hierarchy: PIC mid-range -> 8-bit MCU -> microcontroller -> embedded processor -> semiconductor IC. Mid-range PIC16C parts are typically used where predictable real-time response and ultra-low cost are more important than raw throughput. Key features include a wide 2.5 V to 5.5 V operating range, two on-chip analog comparators with programmable reference, an internal/external oscillator option, a 5-level hardware stack, and a 14-bit instruction set with only 35 single-word instructions. The /I suffix denotes the industrial temperature grade (-40 C to +85 C), and the /SO package designation specifies the 18-pin SOIC wide (300 mil) footprint supplied in tube packaging. The '04' designator marks the 4 MHz speed grade. Architecturally, the device uses an enhanced mid-range core with separate program and data buses, an 8-bit ALU, and 8-level deep hardware stack for subroutine calls. Power management is supported by a wide Vdd range and a low-power Sleep mode with multiple wake-up sources (watchdog timer, external interrupt, comparators, and port change). The comparator peripheral provides direct analog signal conditioning without an external op-amp, simplifying designs that need threshold detection or zero-crossing sensing. Typical applications include blood-pressure monitors, smoke detectors, consumer appliances, battery chargers, security panels, and general-purpose analog-front-end embedded controls. The internal comparators make it a good fit for sensor-threshold systems where an external ADC is unnecessary. When designing with this MCU, plan for the OTP (one-time-programmable) memory limitation: code must be perfect before programming because the program memory cannot be erased and rewritten. For development, use a flash-based sibling (PIC16F62x) or a windowed ceramic package for iterative code work. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

견적 요청 문의하기
PIC16C621A-04I/SS - 8-Bit 4MHz OTP MCU, 1.75KB | Microchip
PIC16C621A-04I/SS

PIC16C621A-04I/SS - 8-Bit 4MHz OTP MCU, 1.75KB | Microchip

The Microchip PIC16C621A-04I/SS is an 8-bit CMOS EPROM/OTP-based microcontroller in the PIC16 family, running at 4 MHz instruction cycle, with 1.75 KB (1K x 14) of OTP program memory and 96 bytes of RAM, housed in a 20-pin SSOP package. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory, data memory, and peripherals. The PIC16C family uses a RISC (Reduced Instruction Set Computer) architecture with only 35 single-word instructions, executed in 200 ns at 4 MHz (4 MHz oscillator) or as fast as 100 ns at higher speeds. The 'C' in PIC16C designates one-time-programmable (OTP) EPROM program memory, while the 'A' suffix denotes the second-generation silicon. OTP allows the device to be programmed once with application firmware using a device programmer, then locked for production use. As an EPROM technology, the PIC16C621A is intended for prototyping, low-volume production, and legacy designs where flash-based PIC16F parts have not yet been qualified. Key features include 13 digital I/O pins, 2 analog comparators, a watchdog timer, power-on reset, brown-out detection, and an internal 4 MHz RC oscillator option. The wide 2.5 V to 6.0 V operating voltage range and -40 °C to +85 °C industrial temperature grade allow deployment in harsh embedded environments. Low-power operation is supported with typical current of 15 µA at 5 V / 4 MHz and 1 µA at 3 V / 32 kHz, making the PIC16C621A attractive for power-sensitive designs. The PIC16C621A architecture pairs the PIC RISC core with dedicated peripheral modules including two on-chip analog comparators that can be combined with external passive components for ADC-style signal conditioning, plus a Timer0 8-bit counter/timer with programmable prescaler. The 14-bit instruction word is wider than typical 8-bit MCUs, providing constant opcodes that execute in a single cycle. Typical applications include industrial control logic, sensor signal conditioning using the on-chip comparators, automotive body electronics subsystems, appliance control boards, and legacy embedded systems migrating from the original PIC16C621 (the A-suffix is the recommended replacement per Microchip migration document 41122B). When designing with this part, choose the OTP variant for low-volume or legacy-validated designs; for higher-volume or field-reprogrammable needs, evaluate flash-based PIC16F621 or PIC16F628A equivalents that share the same SSOP-20 pinout. The device requires a programmer such as the MPLAB PM3 or PICkit 2/3 to load OTP firmware. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

견적 요청 문의하기
PIC16C621A-20/SO - 8-Bit 20MHz OTP MCU 1.75KB | Microchip
PIC16C621A-20/SO

PIC16C621A-20/SO - 8-Bit 20MHz OTP MCU 1.75KB | Microchip

The Microchip Technology PIC16C621A-20/SO is an 8-bit CMOS microcontroller built on the PIC16C architecture, featuring 20 MHz maximum clock speed, 1.75 KB (1K x 14) of One-Time-Programmable (OTP) program memory, 96 bytes of RAM, and 13 digital I/O lines, all housed in an 18-pin SOIC package. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, RAM, and peripheral interfaces such as timers, comparators, and I/O ports. The PIC16C621A sits in the PIC16C family of OTP-based mid-range microcontrollers, a category below flash-based PIC16F parts in reprogrammability but above baseline PIC10/12/16 devices in peripheral integration. OTP means the program memory is written once and is not erasable, making the part suited to production-run embedded control where firmware is finalized before manufacture. Key features include a 14-bit instruction word, 35 single-word instructions, 100 ns instruction execution at 20 MHz, two analog comparators with programmable reference, a Watchdog Timer with its own on-chip RC oscillator, and brown-out reset support. The device operates from 2.5V to 6.0V across commercial 0C to +70C temperature range, drawing low operating current suitable for battery-influenced designs. Internal oscillator and power-on reset circuitry minimize external component count. Architecturally, the PIC16C621A separates program and data memory (Harvard architecture), allowing simultaneous instruction fetch and data access for deterministic throughput. The RISC-style core achieves 200 ns instruction cycles at 20 MHz oscillator (one instruction cycle per four oscillator clocks), enabling responsive control loops in motor, power, and sensor applications without DSP-class complexity. Typical applications include appliance control, sensor signal conditioning, low-cost motor drivers, security alarm panels, and small consumer electronics. The integrated comparators make it well suited to threshold detection and battery monitoring. The PIC16C621A-20/SO is the surface-mount SOIC-18 variant of the family for commercial-temperature applications. When designing with this device, account for OTP programming: firmware must be fully verified before production programming, since OTP cannot be re-written. Use the MCLR, WDT, and POR features together for reliable reset behavior in noisy industrial environments. This page synthesizes distributor pricing, drop-in package equivalents, and design considerations not found on a single manufacturer or distributor datasheet page, giving procurement and engineering teams a single reference for evaluating the PIC16C621A-20/SO.

견적 요청 문의하기
PIC16C621A-20E/SS - 8-Bit 20MHz 1.75KB OTP MCU | Microchip
PIC16C621A-20E/SS

PIC16C621A-20E/SS - 8-Bit 20MHz 1.75KB OTP MCU | Microchip

The Microchip Technology PIC16C621A-20E/SS is an EPROM-based 8-bit CMOS microcontroller from the PIC16C family, delivering up to 20 MHz operation (200 ns instruction cycle), 1.75 KB of OTP program memory (1K x 14), and 96 bytes of RAM, housed in a 20-pin SSOP package. It features 13 digital I/O pins, two analog comparators, and a wide 2.5 V to 5.5 V operating range, making it a versatile general-purpose MCU for industrial, automotive, and consumer designs. An 8-bit microcontroller is a single-chip computer that integrates a CPU, memory, and peripherals on one die; in the broader hierarchy it sits within microcontrollers, which in turn belong to integrated circuits and the semiconductor category. The PIC16C621A family targets cost-sensitive embedded applications where deterministic instruction execution and small code size outweigh the need for large memory. Built on Microchip's original PIC RISC architecture with only 35 single-word instructions, this MCU is also exceptionally easy to program. Key features include 100 ns instruction execution time, 13 I/O pins with individual direction control, two on-chip analog comparators with configurable reference, an internal watchdog timer, power-on reset, and brown-out detection. The device supports in-circuit serial programming (ICSP) via RB6/RB7, allowing firmware updates without removing the part from the board. The PIC16C621A architecture uses a Harvard-style design with separate program and data buses, enabling simultaneous instruction fetch and operand access. The 14-bit wide instruction word improves code density compared to 12-bit PIC cores, while the OTP EPROM memory allows fast prototype-to-production transitions on the same die. The comparator module can wake the part from Sleep, enabling ultra-low standby power in battery-fed designs. Typical applications include appliance control panels, automotive sensor interfaces, HVAC fan controllers, battery chargers, and simple human-machine interface boards. The wide operating temperature range makes it suitable for both commercial and industrial environments. When designing with the PIC16C621A-20E/SS, ensure VDD decoupling uses a 0.1 uF ceramic capacitor placed within 5 mm of the supply pin, and keep the MCLR pin pulled high through a 10 kohm resistor to avoid spurious resets. The Extended (E) temperature grade supports -40 C to +125 C operation, so the part is appropriate for automotive and industrial deployments. This page synthesizes current distributor pricing, drop-in alternatives from Microchip's 20-pin SSOP PIC family, and practical design notes not consolidated in the manufacturer datasheet.

견적 요청 문의하기
PIC16C621A-20I/SO - 8-bit OTP MCU 1.75KB EPROM 20MHz | Microchip
PIC16C621A-20I/SO

PIC16C621A-20I/SO - 8-bit OTP MCU 1.75KB EPROM 20MHz | Microchip

The Microchip Technology PIC16C621A-20I/SO is an 8-bit CMOS OTP-based RISC microcontroller from the PIC16C62X family, featuring 1.75KB (1K x 14) of one-time-programmable program memory, 96 bytes of RAM, and 13 digital I/O pins. The device runs at up to 20MHz clock speed with a 100 ns instruction execution time, integrates two on-chip analog comparators, and is housed in an 18-pin SOIC (SO) wide-body package suitable for industrial-temperature operation from -40C to +85C. According to the Microchip PIC16C621A datasheet, this part operates from 2.5V to 5.5V, making it compatible with both 3.3V and 5V system rails, and delivers 35 single-word instructions for compact, deterministic embedded code. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, and peripherals such as timers, comparators, and I/O. The PIC16C621A belongs to the PIC16C family of OTP microcontrollers, which sit in the hierarchy of microcontrollers > 8-bit MCUs > PIC16C family > PIC16C62X sub-family > CMOS OTP-based RISC microcontrollers. OTP devices are programmed once and retain code for the life of the part, which is a cost-optimized choice for high-volume, stable-firmware products. Key features include 1.75KB EPROM program memory, 96 bytes of static RAM, two on-chip analog comparators with programmable reference, a watchdog timer, power-on reset, brown-out reset, and 13 bidirectional I/O pins with individual direction control. The Harvard RISC architecture separates program and data buses, allowing simultaneous instruction fetch and operand access for predictable cycle-time behavior. The 8-bit core, 14-bit instruction word, and 35-instruction set simplify code generation in MPLAB and the legacy PIC assembler toolchains. Typical applications span industrial control logic, appliance controllers, sensor signal conditioning front-ends, low-cost remote controls, security keypads, simple user-interface boards, and replacement of 555-timer glue logic with programmable timing sequences. For designers choosing between this part and its flash-based PIC16F or PIC16C cousins, the trade-off is one-time programmability versus in-system reprogrammability; the PIC16C621A is preferred where code stability, lower unit cost, and code-protection via OTP are acceptable.

견적 요청 문의하기