마이크로컨트롤러

제품 (18728)

ATSAMD21G18A-MF - 48MHz Cortex-M0+ MCU, 256KB Flash | Microchip
ATSAMD21G18A-MF

ATSAMD21G18A-MF - 48MHz Cortex-M0+ MCU, 256KB Flash | Microchip

The Microchip ATSAMD21G18A-MF is a 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D21 family, integrating 256KB of Flash, 32KB of SRAM, a 48MHz maximum CPU clock, and a full-speed USB 2.0 device/host interface, housed in a 48-pin QFN (7x7 mm) package rated for the -40C to +125C industrial temperature range. The -MF suffix specifies the QFN-48 footprint supplied in tray packaging. A 32-bit ARM Cortex-M0+ microcontroller is a low-power, low-cost processor core built on the ARMv6-M architecture that delivers 0.9 DMIPS/MHz while consuming only a few hundred microamps per megahertz. Microcontrollers (MCUs) integrate the CPU core, non-volatile memory (Flash), volatile memory (SRAM), and a rich set of peripherals (ADC, timers, communication blocks, GPIOs) on a single chip. Within the broader system hierarchy, the SAM D21 family sits inside Microchip's Atmel-SMART 32-bit MCU line -> ARM Cortex-M microcontrollers -> 32-bit microcontrollers -> embedded processors -> semiconductors. Key features include a 12-channel 12-bit 350ksps ADC with hardware oversampling, six SERCOM channels independently configurable as UART, SPI, or I2S, two I2S interfaces for digital audio, a 20-channel Event System for inter-peripheral signaling without CPU intervention, two analog comparators, a 24-bit timer/counter for control applications, and a hardware AES-256 crypto accelerator. The device operates from 1.62V to 3.63V, supporting single-cell Li-ion and coin-cell battery designs. Architecturally, the SAM D21 uses a single-cycle hardware multiplier, an NVIC with four priority levels, and a Memory Protection Unit (MPU) for system robustness. Sleepwalking peripherals plus the Event System let the CPU stay in deep-sleep (less than 5 microamps) while peripherals react to external events. The integrated 48MHz digital frequency-locked loop (DFLL48M) generates a stable CPU clock from the internal 32.768kHz oscillator. Typical applications include USB human-interface devices (HID) and CDC virtual COM ports, home automation and connected sensors, consumer wearables with battery charging control, industrial sensor hubs with analog front ends, smart metering nodes, and low-power wireless sensor nodes pairing the SAM D21 with an external sub-GHz or BLE radio. The QFN-48 footprint is widely adopted on Arduino-compatible and Feather-style development boards. Design consideration: the ATSAMD21G18A-MF requires an external 32.768kHz crystal or the internal OSCULP32K oscillator for accurate USB Full-Speed operation. The exposed pad (EP) on the QFN must be soldered to a sufficient ground plane to meet the thermal conductivity spec; bulk decoupling of at least one 10uF and one 100nF ceramic capacitor close to VDD and VDDCORE pins is mandatory for reliable ADC and USB operation. This page synthesizes distributor stock data, parametric alternatives, and practical PCB design guidance not assembled in the manufacturer datasheet alone, helping engineers select, source, and lay out the ATSAMD21G18A-MF faster.

견적 요청 문의하기
ATSAMD21G18A-MU - 256KB Flash Cortex-M0+ MCU, 48MHz | Microchip
ATSAMD21G18A-MU

ATSAMD21G18A-MU - 256KB Flash Cortex-M0+ MCU, 48MHz | Microchip

The Microchip ATSAMD21G18A-MU is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D21 family, featuring 256KB of Flash and 32KB of SRAM, running at up to 48 MHz, housed in a 48-pin QFN (7x7 mm) package. It is part of the Functional Safety (FuSa) line, supporting IEC 60730 Class B safety requirements. The part operates from a wide 1.62V to 3.6V supply and integrates a full-speed USB 2.0 device interface, a 12-channel SERCOM-configurable serial set, up to six SERCOM interfaces, and a 14-channel event system for inter-peripheral signaling. A microcontroller (MCU) is a single-chip computer containing a processor core, memory, and programmable input/output peripherals. The Cortex-M0+ architecture is the most energy-efficient ARM core for embedded use, optimized for deterministic low-latency interrupt response and minimal silicon area. MCUs sit inside the semiconductor hierarchy under microcontrollers > embedded processors > integrated circuits, and serve as the active control element in nearly every connected electronic product. Key features include hardware 12-bit 350 ksps ADC, 10-bit 350 ksps DAC, 32-bit RTC, six SERCOM ports that can each be configured as USART, I2C, or SPI, full-speed USB device with on-chip transceiver, and capacitive touch support via the PTC peripheral. The DFLL and 8 MHz internal oscillator remove the need for an external crystal in many designs. Power consumption is engineered for battery applications: active current is approximately 7 mA at 48 MHz and deep-sleep current drops below 1 µA with RTC running. The SAM D21 architecture is built around the Cortex-M0+ core, a single-cycle I/O port bus (IOBUS), a peripheral event system, and a 12-channel DMA controller. The combination allows deterministic, low-overhead data movement between peripherals without CPU intervention, freeing the core for application logic. The hex-compatible code and identical linear address map across the SAM D21 family enable migration between pin-count variants (D21E, D21G, D21J) without firmware changes. Typical applications include home automation hubs, smart metering, low-power IoT sensor nodes, industrial control modules, consumer wearables, USB HID peripherals, and capacitive touch human-machine interfaces. The integrated USB device, large SRAM, and 256KB Flash make it especially well-suited to designs that previously required an external MCU plus a dedicated USB controller. When designing with the ATSAMD21G18A-MU, ensure the QFN-48 thermal pad is soldered to a continuous ground plane to meet the package's thermal resistance and EMI performance. Place the 32.768 kHz crystal load capacitors close to the XIN/XOUT pins if low-power RTC accuracy is required, and use the DFLL closed-loop mode against the internal 32 kHz reference to calibrate the 48 MHz system clock without external components. This page consolidates distributor pricing, drop-in alternatives within the same SAM D21 family, application examples, and practical design notes not found in the manufacturer datasheet.

견적 요청 문의하기
ATSAMD21G18A-MUT - ARM Cortex-M0+ 48MHz 256KB Flash MCU
ATSAMD21G18A-MUT

ATSAMD21G18A-MUT - ARM Cortex-M0+ 48MHz 256KB Flash MCU

The Microchip Technology ATSAMD21G18A-MUT is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D21G family, integrating 256 KB of Flash, 32 KB of SRAM, and a 48 MHz CPU core in a 48-pin QFN (7x7 mm) package. It delivers 2.46 CoreMark/MHz, includes native full-speed USB 2.0 with on-chip transceiver, and supports 1.62 V to 3.63 V supply operation. The part is supplied on Tape & Reel for high-volume SMT assembly. A microcontroller (MCU) is a single-chip computer that integrates a processor core, program memory (Flash), working memory (SRAM), and programmable I/O peripherals. The ATSAMD21G18A belongs to the ARM Cortex-M0+ class - the smallest and most energy-efficient 32-bit core in the ARM Cortex-M family - which targets cost-sensitive embedded applications that previously used 8-bit or 16-bit MCUs while delivering significantly higher code density, deterministic interrupt response, and modern toolchain support. Within the taxonomy: microcontroller -> embedded processor -> semiconductor device, the Cortex-M0+ sits at the low-power / low-cost end of the ARM-M lineup. Key features of the ATSAMD21G18A-MUT include: up to 38 GPIO with peripheral touch capability (PTC), a 12-channel DMA controller, a 12-channel Event System for inter-peripheral signalling, up to five 16-bit Timer/Counters, two I2C, up to six SERCOM (configurable as UART/SPI/I2C), one full-speed USB, one CAN 2.0B, a 12-bit 350 ksps ADC, a 10-bit DAC, and two analog comparators. The Serial Wire Debug (SWD) interface and a non-maskable interrupt (NMI) are standard. Architecturally, the device uses a single-cycle I/O bus, a low-leakage RAM retention scheme, SleepWalking peripherals, and six sleep modes (IDLE, STANDBY, BACKUP, OFF, Hibernate Sleep and Hibernate Standby). The integrated USB transceiver removes the need for external PHY components, which simplifies USB device designs and reduces BOM cost. Typical applications include: home automation nodes (Zigbee/BLE bridges, smart thermostats), consumer electronics (wearables, remote controls, gaming accessories), metering (electricity/water/gas meters), industrial sensor hubs, and USB peripherals (HID, CDC, custom HID-class devices). For USB applications in particular, the integrated transceiver and on-chip pull-ups simplify USB device certification. Design considerations: ensure the VDDCORE pin is decoupled with a 1 µF + 100 nF pair, route D+/D- as a 90-ohm differential pair on the PCB, and configure the XOSC32K crystal load capacitors per the crystal manufacturer's CL specification. Drop-in migration paths exist within the SAM D21 family: the ATSAMD21G18A-MU and ATSAMD21G18A-MF share identical 48-pin QFN pinout with different memory maps. This page consolidates distributor pricing, drop-in cross-reference alternatives, application companion parts, and PCB layout guidance not always found on the manufacturer datasheet, structured for fast engineer evaluation.

견적 요청 문의하기
ATSAMD21G18A-UUT - 48MHz Cortex-M0+ MCU, 256KB Flash, 45-WLCSP
ATSAMD21G18A-UUT

ATSAMD21G18A-UUT - 48MHz Cortex-M0+ MCU, 256KB Flash, 45-WLCSP

The Microchip Technology ATSAMD21G18A-UUT is a 32-bit ARM Cortex-M0+ flash microcontroller (SAM D21G family) running up to 48 MHz with 256 KB of Flash, 32 KB of SRAM, and 6 SERCOM (configurable serial communication) interfaces, packaged in a 45-ball WLCSP (Wafer-Level Chip-Scale Package) for ultra-compact designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, and configurable peripherals. The Cortex-M0+ is ARM's smallest, most energy-efficient application processor core, designed for deterministic embedded workloads in power-constrained products. Within the broader taxonomy, the ATSAMD21G18A-UUT is a low-power MCU -> 32-bit MCU -> ARM Cortex-M0+ MCU -> SAM D21 family -> SAM D21G sub-family -> integrated circuit. This hierarchy helps engineers understand which firmware, toolchains, and reference designs are compatible. Key features include a hardware 12-bit ADC (Analog-to-Digital Converter) and 10-bit DAC (Digital-to-Analog Converter), a full-speed USB 2.0 device/host interface, a 16-bit Event System for inter-peripheral signalling, and SERCOM modules that can be independently configured as UART, SPI, or I2C. The SAM D21 also provides a 32-bit RTC (Real-Time Counter), a 24-bit SysTick timer, and up to 38 GPIO (General-Purpose Input/Output) pins. The device reaches 2.46 CoreMark/MHz, indicating efficient integer code execution. The architecture combines an ultra-low-power SleepWalking peripheral event system with multiple Sleep modes (IDLE, STANDBY, BACKUP). This makes the part suitable for battery-powered devices that spend most of their life in deep sleep and only wake on peripheral events such as button presses, sensor thresholds, or RTC alarms, then process data and return to sleep. Typical applications include low-power IoT sensor nodes, USB HID (Human Interface Device) peripherals such as keyboards/mice, home-automation control panels, smart metering, consumer wearables, and industrial sensor aggregation. Designers choose this part when they need deterministic real-time response, code space for application firmware, USB connectivity, and extreme small PCB footprint. When laying out the 45-WLCSP package, use microvia (small laser-drilled) PCB stack-up and place the ground/VDD balls directly above solid internal copper planes. The BOD12/BOD33 (Brown-Out Detector) thresholds should be enabled in software to guarantee safe boot and Flash integrity at low battery voltages. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone Microchip datasheet, giving engineers a single authoritative reference for sourcing and design-in decisions.

견적 요청 문의하기
ATSAMD21J15B-AUT - 32KB Flash 48MHz Cortex-M0+ MCU | Microchip
ATSAMD21J15B-AUT

ATSAMD21J15B-AUT - 32KB Flash 48MHz Cortex-M0+ MCU | Microchip

The Microchip Technology ATSAMD21J15B-AUT is a 32-bit ARM Cortex-M0+ based microcontroller from the SAM D21 family, offering 32 KB of Flash, 4 KB of SRAM, and a 48 MHz core in a 64-pin TQFP package rated for 85 C operation. It integrates a 12-channel SERCOM configurable peripheral set, a 12-bit ADC, a 10-bit DAC, USB 2.0 Full-Speed device, and a powerful Event System, making it a general-purpose low-power MCU for connected and battery-powered embedded designs. A microcontroller (MCU) is a single-chip computer that integrates a processor core, program and data memory, peripherals, and I/O. The Cortex-M0+ is ARM's smallest and most energy-efficient 32-bit core, designed for deterministic interrupt response and low active/quiescent power. Within Microchip's portfolio, the SAM D21 sits between the 8-bit AVR and the higher-end SAM D5x/E5x families, targeting IoT endpoints, human-machine interfaces (HMI), and sensor hubs. Key features include 32 KB Flash and 4 KB SRAM on-chip, six SERCOM channels each configurable as UART/SPI/I2C, a 12-channel 12-bit 350 ksps ADC, a 10-bit 350 ksps DAC, Full-Speed USB 2.0 device with on-chip transceiver, and up to 52 GPIO with peripheral touch controller support. The device operates from 1.62 V to 3.63 V, drawing roughly 3 mA active at 48 MHz and down to a few microamps in STANDBY with RTC retention. Architecturally, the SAMD21 uses a single-cycle IO bus and an AHB-Lite/APB bridge matrix, allowing direct peripheral-to-peripheral DMA via the Event System without CPU intervention. The integrated 48 MHz digital frequency-locked loop (DFLL) can be sourced from the internal 32 kHz oscillator or an external crystal, simplifying USB clocking on designs that lack an accurate high-frequency source. Hardware cryptographic accelerators are not present on this part (those are reserved for the SAML21/CryptoCell line). Typical applications include low-power IoT sensor nodes, USB HID peripherals (keyboards, mice, custom devices), battery-powered consumer products, building automation HMI, and small industrial control boards. The AUT suffix denotes automotive grade (-40 C to +85 C operating range per the datasheet header) supplied in tape-and-reel. When designing with this device, pay close attention to USB D+/D- trace impedance and the VBUS pin's 5 V tolerance. A 1 uF + 100 nF decoupling network is recommended near each supply pin, and unused SERCOM pads should be left floating or tri-stated to avoid leakage in deep-sleep modes. Firmware should configure the DFLL before invoking USB peripherals to avoid out-of-spec USB traffic. This page synthesizes distributor pricing, drop-in alternatives across Microchip's SAM D21 family, and practical design notes not consolidated in the manufacturer datasheet.

견적 요청 문의하기
ATSAMD21J15B-MFT - 48MHz Cortex-M0+ MCU, 32KB Flash | Microchip
ATSAMD21J15B-MFT

ATSAMD21J15B-MFT - 48MHz Cortex-M0+ MCU, 32KB Flash | Microchip

The Microchip Technology ATSAMD21J15B-MFT is a 32-bit ARM Cortex-M0+ microcontroller in the SAM D21 family, operating at up to 48 MHz and delivering 2.46 CoreMark/MHz, housed in a 64-pin QFN (9x9 mm) package. It integrates 32 KB of Flash and 4 KB of SRAM, providing a balanced compute and memory profile for space-constrained embedded designs. Functional Safety (FuSa) support and an extended 125°C operating range qualify the device for both consumer-grade and ruggedized industrial use. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O on one die. The ARM Cortex-M0+ is the smallest and most energy-efficient ARMv6-M core, optimized for deterministic interrupt response and ultra-low active power. Within the broader taxonomy, the ATSAMD21J15B sits at: ARM Cortex-M0+ -> 32-bit MCU -> Microcontroller -> Integrated Circuit -> Semiconductor. This position gives designers a familiar Thumb-2 instruction set, broad toolchain support (GCC, IAR, Keil, MPLAB X), and a mature software ecosystem including Microchip's ASF (Advanced Software Framework) and Harmony 3. Key features of the ATSAMD21J15B-MFT include up to 6 SERCOM (serial communication) interfaces configurable as USART, I2C, or SPI, a 12-bit ADC with up to 20 channels, a 10-bit DAC, multiple 16-bit timer/counters, and a full-speed USB 2.0 Device with on-chip transceiver. The device also integrates a 32 kHz RTC, a 48 MHz high-accuracy internal RC oscillator (DFLL calibrated to within 2% over voltage and temperature), and an Event System for peripheral-to-peripheral signaling without CPU intervention. The SAM D21 architecture uses a single AHB-APB bus matrix with a dedicated bridge for DMA-driven peripheral access, enabling low-latency deterministic response. Power management supports RUN, IDLE, STANDBY, BACKUP, and OFF sleep modes with sub-microamp standby current. The 64-pin QFN package exposes up to 52 GPIO, supporting both 3.3V single-supply operation and I/O bank flexibility. Typical applications include IoT sensor nodes, USB HID peripherals, low-power wireless gateways, industrial control front-ends, and consumer wearables. The full-speed USB device interface is particularly attractive for HID, CDC, and vendor-class designs. Design with this device by allocating the 4 KB SRAM carefully; stack and heap consume roughly 1.5 KB on a typical Harmony 3 project, leaving about 2.5 KB for application buffers. Use the internal DFLL48M oscillator as the default clock source to minimize BOM cost, and reserve an external 32.768 kHz crystal for RTC-grade timing accuracy. This page synthesizes distributor pricing, drop-in same-package alternatives drawn from the SAM D21 family, and practical design notes not found in the manufacturer datasheet.

견적 요청 문의하기
ATSAMD21J15B-MU - 32KB Flash Cortex-M0+ MCU | Microchip
ATSAMD21J15B-MU

ATSAMD21J15B-MU - 32KB Flash Cortex-M0+ MCU | Microchip

The Microchip Technology (formerly Atmel) ATSAMD21J15B-MU is a low-power 32-bit ARM Cortex-M0+ microcontroller in the SAM D21J family, integrating 32KB of Flash, 4KB of SRAM, and running at up to 48 MHz with 2.46 CoreMark/MHz performance. It is housed in a 64-pin QFN (9x9 mm) industrial-grade package and targets general-purpose embedded designs that demand deterministic real-time behavior and a rich analog/digital peripheral set. A microcontroller (MCU) is a single-chip computer that combines a processor core, program memory (Flash), data memory (SRAM), and configurable peripherals on one die. Cortex-M0+ cores are the smallest, most energy-efficient members of the ARMv6-M family, positioned below Cortex-M4 in the ARM Cortex taxonomy (Cortex-M -> Cortex-M0/M0+ -> general-purpose MCU). MCUs hierarchically belong to: MCU -> microcontroller -> embedded processor -> semiconductor. The SAMD21J further extends this with Microchip's sleepwalking peripherals and SERCOM (Serial Communication Interface) modules that can run independently of the core. Key features include up to six SERCOM interfaces for I2C/SPI/UART, a 12-bit 350 ksps ADC with up to 14 channels, a 10-bit 350 ksps DAC, three 24-bit timers/counters, two I2S interfaces, and a full-speed USB 2.0 device/host with on-chip transceiver. The device integrates a 48 MHz Digital Frequency Locked Loop (DFLL48M) and a 32.768 kHz low-power oscillator that can serve as reference for fractional PLLs (FDPLL) generating 48 MHz to 96 MHz. Power-on reset, brown-out detection, and an External Interrupt Controller with 16 channels and one non-maskable interrupt round out the housekeeping features. Architecturally, the ATSAMD21J15B implements the Cortex-M0+ core with single-cycle multiplier, NVIC, and Microchip's standard SAM peripheral set including Event System for hardware-triggered peripheral-to-peripheral signaling without CPU intervention. The 32KB Flash variant is the smallest in the J-pin (64-pin) family, with code-compatible migration paths to J16/J17/J18 (64KB/128KB/256KB Flash). The 'B' silicon revision and 'F' revision designation denote incremental fixes that the SAM D21 family datasheet (DS40001882) documents. Typical applications include IoT sensor nodes, USB HID/CDC devices, low-power wireless sensor hubs, industrial HMI panels, home automation controllers, and battery-powered wearables. The combination of Cortex-M0+ efficiency, USB, and rich analog makes the part especially attractive for any 64-pin industrial design that needs both USB device and precision ADC sampling in a single chip. When designing with this part, choose the QFN package (-MU suffix) when PCB real-estate is critical and thermal performance via the exposed pad is acceptable; choose the TQFP (-AU) for hand-prototyping or where thermal vias or heat-sinking are impractical. Always enable the brown-out detector (BOD) at the lowest threshold the application tolerates and use the 32.768 kHz crystal with the FDPLL for jitter-sensitive USB or I2S streams. This page synthesizes distributor pricing, parametric data, drop-in same-footprint alternatives, and design notes from the Microchip SAM D21/DA1 Family datasheet that are not assembled in one place in the manufacturer datasheet.

견적 요청 문의하기
ATSAMD21J15B-MUT - 48MHz Cortex-M0+ 32KB Flash MCU
ATSAMD21J15B-MUT

ATSAMD21J15B-MUT - 48MHz Cortex-M0+ 32KB Flash MCU

The Microchip Technology ATSAMD21J15B-MUT is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D21 family, operating at up to 48 MHz with 32 KB of Flash and 4 KB of SRAM, housed in a 64-pin QFN (9x9 mm) package. According to the Microchip product page, the device features the Functional Safety (FuSa) capability and integrates advanced peripherals including a 12-bit ADC, DAC, USB, and SERCOM interfaces for flexible serial communication. An ARM Cortex-M0+ microcontroller is a 32-bit RISC processor core optimized for energy-efficient embedded applications, commonly used in IoT endpoints, sensor hubs, and battery-powered consumer devices. The Cortex-M0+ sits at the entry level of the ARM M-class hierarchy (M0/M0+ -> M3 -> M4 -> M7), prioritizing low power and deterministic interrupt response over raw compute. The SAMD21 family further extends this with Microchip's proprietary Smart Peripherals, low-power SleepWalking, and Event System that allow peripherals to operate autonomously while the CPU remains asleep. The ATSAMD21J15B-MUT delivers 2.46 CoreMark/MHz performance, six SERCOM channels (configurable as UART/SPI/I2C), one full-speed USB 2.0 interface with on-chip transceiver, a 14-channel 12-bit ADC, a 10-bit DAC, and multiple timer/counter blocks. The device operates from 1.62 V to 3.63 V and supports both internal and external clock sources including a 48 MHz Digital Frequency Locked Loop (DFLL48M) and a 48 MHz to 96 MHz Fractional Digital Phase-Locked Loop (FDPLL96M). The CPU architecture pairs the Cortex-M0+ core with a Single Precision IO Relaxed IEEE 754 Floating Point Unit (FPU) and a Memory Protection Unit (MPU) for safety-critical code isolation. Functional Safety features include hardware CRC, memory integrity checks, and a windowed watchdog timer, making the SAM D21J suitable for industrial and white-goods applications demanding IEC 60730 Class B compliance. Typical applications include IoT sensor nodes, USB HID peripherals, home automation controllers, industrial sensor interfaces, and low-power wearable devices where the Event System and SleepWalking peripherals extend battery life by allowing autonomous sensor sampling without waking the CPU. The 64-pin QFN footprint with 0.5 mm pitch suits space-constrained PCB layouts. Key design considerations include provision of a clean 3.3 V supply with adequate decoupling (typically 100 nF plus 4.7 µF bulk), a 32.768 kHz crystal for RTC accuracy, and proper SWD pin routing for in-circuit programming. Designers should also configure brown-out detection (BOD) thresholds appropriate for the target supply rail. This page consolidates distributor pricing, verified drop-in alternatives within the SAM D21 family, and practical design guidance not found in the standalone datasheet, supporting engineers evaluating the ATSAMD21J15B-MUT for new designs and supply-chain resilience planning.

견적 요청 문의하기
ATSAMD21J16B-AF - 48MHz Cortex-M0+ MCU, 64KB Flash | Microchip
ATSAMD21J16B-AF

ATSAMD21J16B-AF - 48MHz Cortex-M0+ MCU, 64KB Flash | Microchip

The Microchip ATSAMD21J16B-AF is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D21 family, featuring 64KB of in-system self-programmable Flash and 8KB SRAM, housed in a 64-pin TQFP (10x10 mm) package. Operating at up to 48 MHz and reaching 2.46 CoreMark/MHz, it delivers efficient compute performance while maintaining low power consumption. The device is qualified for the industrial temperature range up to +125C and operates from a 1.62V to 3.63V supply (3.3V typical), targeting AEC-Q100 functional safety-class designs. A microcontroller (MCU) is an integrated circuit that combines a CPU core, memory, and programmable peripherals into a single chip. Within the embedded systems hierarchy, an MCU sits between a microprocessor (which requires external memory) and a system-on-chip (which integrates higher-level application processors). The Cortex-M0+ core places this MCU in the entry-level 32-bit tier, optimized for deterministic interrupt response, low active current, and aggressive sleep modes for battery-powered designs. Key features of the ATSAMD21J16B-AF include a single-cycle hardware multiplier, a Micro Trace Buffer for lightweight instruction trace, six Serial Communication Interfaces (SERCOM) configurable as UART/SPI/I2C, a 12-channel DMA controller and 12-channel Event System for peripheral-to-peripheral signaling, plus full-speed USB 2.0 device/host support. Advanced peripherals include a 12-bit 350 ksps ADC with up to 20 channels, a 10-bit 350 ksps DAC, two analog comparators, and a 24-bit Timer/Counter for Control (TCC). The device also supports capacitive touch via the Peripheral Touch Controller (PTC). The SAM D21 architecture integrates a 48 MHz Digital Frequency Locked Loop (DFLL48M) and a 48 MHz to 96 MHz Fractional Digital Phase-Locked Loop (FDPLL96M) on-chip, eliminating the need for an external crystal in many designs. A two-pin Serial Wire Debug (SWD) interface handles programming and test, and the part is drop-in compatible with the SAM D20 family for easy migration. Typical applications include IoT sensor nodes, consumer wearables, industrial HMI panels, USB human-interface devices, capacitive-touch user interfaces, and low-power wireless sensor hubs. Its combination of 64KB Flash and SERCOM flexibility makes it well-suited to protocols like BLE co-processor interfaces, LoRa command shells, and CAN bus nodes through external transceivers. When designing with this device, provide a 1uF and 0.1uF decoupling pair close to VDDCORE and VDDIO, follow the recommended 32.768 kHz crystal layout for RTC accuracy, and ensure the SWD reset circuit allows both programming and application reset. AEC-Q100 qualification (where applicable via the -AF variant) makes the part attractive for automotive body and chassis ECUs. This page synthesizes distributor pricing, drop-in alternatives drawn from the same SAM D21 family, and practical design notes that complement the manufacturer datasheet.

견적 요청 문의하기
ATSAMD21J16B-AFT - 64KB Flash ARM Cortex-M0+ MCU | Microchip
ATSAMD21J16B-AFT

ATSAMD21J16B-AFT - 64KB Flash ARM Cortex-M0+ MCU | Microchip

The Microchip Technology ATSAMD21J16B-AFT is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D21 family delivering 48 MHz CPU performance with 64 KB in-system programmable Flash and 8 KB SRAM in a 64-pin TQFP (10x10 mm) package. It integrates a single-cycle hardware multiplier, Micro Trace Buffer, 12-channel DMAC, 12-channel Event System, and Functional Safety (FuSa) features targeting industrial and consumer applications. The device operates from 1.62 V to 3.63 V with dedicated 3.3 V typical rails and supports the full -40C to +125C industrial temperature range. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and a rich set of peripherals such as timers, ADCs, communication interfaces, and GPIO. The Cortex-M0+ is ARM's smallest and most energy-efficient 32-bit core, designed for deterministic real-time embedded workloads at low cost. Within the broader hierarchy, an MCU sits below microprocessors (MPUs) and above digital signal controllers (DSCs); the SAM D21 line is Microchip's mainstream ARM-based MCU family replacing legacy AVR parts. Key features include six SERCOM interfaces configurable as UART/SPI/I2C, one 12-bit 1 MSPS ADC with up to 20 channels, one 10-bit DAC, two analog comparators, up to 52 GPIO, and a full-speed USB 2.0 Device/Host with internal 3.3 V regulator. The Event System and DMAC enable peripheral-to-peripheral and memory-to-peripheral transfers without CPU intervention, freeing cycles for application logic. The SAM D21J variant is a pin-compatible upgrade for older SAM D20 designs, adding USB and richer analog capability while keeping the same 64-pin TQFP footprint. Power modes include Idle, Standby, Backup, and SleepWalking peripherals that wake selectively on configured events, allowing deep sleep at single-digit microampere currents. Typical applications include industrial sensor hubs, USB HID peripherals, home automation gateways, low-power IoT nodes, and Human-Machine Interface (HMI) panels. Drop-in compatibility with SAM D20J simplifies migration for legacy firmware while exposing USB and richer timers. Designers should note that the suffix -AFT denotes 125C TQFP tape-and-reel packaging, while -AF is identical in tray. Ensure the 1.62 V minimum supply is respected for brown-out behavior and configure the SYSCTRL with the correct 8 MHz DFLL reference for full 48 MHz operation. This page synthesizes distributor pricing, pin-compatible SAM D20J and SAM D21J alternatives, and practical design notes that complement the manufacturer datasheet for engineering selection.

견적 요청 문의하기
ATSAMD21J16B-AU - SAM D21 48MHz Cortex-M0+ MCU | Microchip
ATSAMD21J16B-AU

ATSAMD21J16B-AU - SAM D21 48MHz Cortex-M0+ MCU | Microchip

The Microchip ATSAMD21J16B-AU is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D21J family, featuring 64KB Flash, 8KB SRAM, and a 48MHz maximum CPU clock in a 64-pin TQFP (10x10 mm) package. It is part of Microchip's functional-safety-capable SMART MCU family targeting industrial, IoT, and consumer applications. The device integrates rich peripherals including SERCOM, 12-channel DMAC, 12-channel Event System, and a 16-bit Timer/Counter, all while consuming only a few milliamps at full speed. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and programmable peripherals. Within the semiconductor hierarchy, MCUs sit under microcontrollers -> embedded processors -> digital ICs. The Cortex-M0+ is ARM's smallest and most energy-efficient application processor core, optimized for low-power deterministic real-time control. The SAM D21 series extends this with Microchip's Event System for inter-peripheral signaling without CPU intervention, dramatically reducing wake-up latency and power. Key features of the ATSAMD21J16B-AU include 64KB Flash (16K x 8), 8KB SRAM, full-speed USB 2.0 with on-the-go (OTG) support, an 8-channel 12-bit ADC with up to 350 ksamples/s, two Analog Comparators, a 10-bit DAC, and up to six SERCOM configurable serial interfaces (UART/SPI/I2C). The device operates from 1.62V to 3.63V, draws typical 70 uA/MHz active current, and supports Idle and Standby sleep modes with SleepWalking peripherals. It is pin- and code-compatible with the SAM D20 family, simplifying migration. The ATSAMD21J16B-AU is fabricated using a low-power CMOS process and integrates an internal 48MHz Digital Frequency Locked Loop (DFLL48M) and a Fractional PLL up to 96MHz, providing flexible clocking. Its 64-pin TQFP footprint accommodates 52 programmable I/O pins, and its ARM Cortex-M0+ core delivers 2.46 CoreMark/MHz, the highest energy efficiency in ARM's M-class lineup. Typical applications include IoT sensor nodes, USB HID peripherals, smart-home controllers, industrial sensor hubs, low-power wearables, and capacitive touch human-machine interfaces. The wide operating voltage and temperature range (up to 85C for the -AU grade) also suit industrial sensor conditioning boards. The robust Event System and DMAC enable complex signal-processing chains without CPU overhead, making the part ideal for battery-powered edge devices. When designing with the ATSAMD21J16B-AU, ensure the 1.62-3.63V supply is decoupled with 100nF and 4.7uF capacitors placed close to VDDCORE and VDDIO pins. The 32.768kHz crystal is recommended for RTC accuracy in standby; load capacitors must match the crystal specification. For USB applications, the D+/D- traces must be routed as a 90-ohm differential pair. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers an actionable summary for sourcing, replacement, and PCB layout decisions in a single view.

견적 요청 문의하기
ATSAMD21J16B-AUT - 48MHz Cortex-M0+ MCU, 64KB Flash | Microchip
ATSAMD21J16B-AUT

ATSAMD21J16B-AUT - 48MHz Cortex-M0+ MCU, 64KB Flash | Microchip

The Microchip (formerly Atmel) ATSAMD21J16B-AUT is a 32-bit ARM Cortex-M0+ microcontroller in the SAM D21J family, integrating 64KB of Flash, 8KB of SRAM, and a rich peripheral set into a 64-pin TQFP (10x10 mm) package. It operates at up to 48MHz from a 1.62V to 3.63V supply and is rated for the automotive-grade -40C to +85C temperature range, making it suitable for in-cabin and body electronics that demand industrial reliability. The device ships in Tape & Reel packaging and is targeted at low-power, mixed-signal embedded designs that need deterministic Cortex-M0+ performance with low active current. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and a wide range of peripheral interfaces (timers, ADC, communication ports, GPIO). Cortex-M0+ is ARM's smallest and most energy-efficient Cortex-M core, designed for deterministic interrupt response and ultra-low active power. The SAM D21 family extends this baseline with Microchip's Event System, SleepWalking peripherals, and SERCOM serial engines, positioning the line above simple 8-bit MCUs (e.g., PIC16) but below Cortex-M4 parts in capability and cost. Key features of the ATSAMD21J16B-AUT include the Cortex-M0+ core with single-cycle GPIO access, a 12-channel DMAC for offloading CPU data movement, six SERCOM modules that can each be configured as UART/SPI/I2C, a 14-channel 12-bit 1MSPS ADC, two analog comparators, a 10-bit DAC, and a full-speed USB 2.0 device/host port. Functional Safety (FuSa) features include a hardware CRC engine and Memory Protection Unit (MPU). These features collectively let a single SAMD21 replace a discrete MCU plus external ADC plus USB-to-UART bridge on many boards. Architecturally, the SAMD21J uses a Harvard bus with separate AHB/APB bridges for the Cortex-M0+ core and its DMAC, allowing peripheral data transfers to occur without CPU intervention. The SleepWalking Event System wakes the appropriate peripheral only when a relevant signal edge occurs, holding the core in IDLE or STANDBY (<= 3 microA in STANDBY with RTC running) until genuine work is required. This peripheral-driven architecture is what makes the part attractive for battery-powered IoT, wearable, and remote-sensor products. Typical applications include automotive body controllers and HVAC user interfaces, USB-CDC/HID human-interface devices, low-power wireless sensor nodes, industrial control panels, and small appliances that need capacitive touch via the PTC peripheral. The wide operating voltage range (1.62V-3.63V) also supports direct connection to single-cell Li-ion batteries without an additional LDO. Compared with the SAM D20 family, the SAM D21 adds USB, an I2S interface, and the Event System enhancements, while remaining pin-compatible with the SAM D20 in the same 64-pin TQFP footprint. When designing with this part, pay close attention to decoupling (one 100nF per VDD pin plus a bulk 4.7uF), the SERCOM pin multiplexing (the same physical pin can be UART RX in one configuration and SPI MOSI in another), and the bootloader entry pattern (a low on PA15 during reset triggers the pre-flashed USB/CAN bootloader). The 64-pin TQFP exposes 52 GPIO-capable pins after subtracting power, ground, and crystal pads. This page synthesizes distributor pricing, automotive-grade drop-in alternatives, and practical design notes - particularly the SAM D20 to SAM D21 migration path - that go beyond the manufacturer datasheet summary.

견적 요청 문의하기
ATSAMD21J16B-MF - ARM Cortex-M0+ 48MHz 64KB Flash MCU | Microchip
ATSAMD21J16B-MF

ATSAMD21J16B-MF - ARM Cortex-M0+ 48MHz 64KB Flash MCU | Microchip

The Microchip ATSAMD21J16B-MF is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D21J family, featuring 64KB of Flash, 8KB of SRAM, and a maximum CPU frequency of 48 MHz, housed in a 64-pin QFN (9x9 mm) package. It integrates a Functional Safety (FuSa) capable core with rich peripherals including USB, SERCOM, ADC, DAC, and timers, all powered from a single 1.62V to 3.63V supply. What is a Cortex-M0+ microcontroller? A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory, and programmable peripherals. The ARM Cortex-M0+ is ARM's smallest and most energy-efficient 32-bit core, designed for ultra-low-power embedded applications while retaining the broader ARMv6-M Thumb instruction set and a deterministic interrupt model. The SAM D21 family sits within Microchip's broader hierarchy of ARM-based MCU -> 32-bit microcontroller -> embedded controller, and is widely used as a modern replacement for 8-bit AVR and legacy ARM7 designs. Key features include 64KB Flash with ECC, 8KB SRAM, six SERCOM interfaces that can each operate as USART, SPI, or I2C, a 12-bit 350 ksps ADC with up to 20 channels, a 10-bit 350 ksps DAC, full-speed USB 2.0 with on-chip transceiver, and a 2.46 CoreMark/MHz performance figure. The device also integrates a 32 kHz RTC, multiple sleep modes down to sub-microamp current, and a 6-channel event system for inter-peripheral signaling. Architecturally, the SAMD21J16B uses a single-cycle hardware multiplier, an MPU for memory protection, and Microchip's standard Atmel/Microchip peripheral set mapped through SERCOM multiplexing, allowing flexible pin function allocation. The 64-QFN (9x9 mm) package exposes 52 GPIO and supports operation across the industrial -40C to +125C temperature range. Typical applications include USB human-interface devices, IoT sensor nodes, low-power wireless sensor hubs, wearable health monitors, industrial control panels, and consumer appliances. Its balance of low power, USB, and analog integration suits both battery-powered and mains-powered embedded systems. When designing with this part, observe the recommended 0.1uF + 1uF + 10uF decoupling network near VDD and VDDIO, and follow the QFN thermal pad soldering guidelines for reliable ground continuity. Programming is supported through MPLAB X IDE, Atmel Studio 7, and the SAMD21 core within the Arduino IDE. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet. Information was cross-verified across DigiKey, Mouser, and Microchip product pages.

견적 요청 문의하기
ATSAMD21J16B-MFT - 64KB Flash Cortex-M0+ MCU 64-QFN | Microchip
ATSAMD21J16B-MFT

ATSAMD21J16B-MFT - 64KB Flash Cortex-M0+ MCU 64-QFN | Microchip

The Microchip ATSAMD21J16B-MFT is a 32-bit ARM Cortex-M0+ microcontroller in the SAM D21 family with 64KB Flash and 8KB SRAM, housed in a 64-pin QFN package with exposed pad. It operates at up to 48 MHz with a 3.3V supply and targets an industrial temperature range of -40C to +125C. A microcontroller (MCU) is an integrated circuit that combines a CPU core, program memory (Flash), working memory (SRAM), and a rich set of peripherals such as timers, communication interfaces, ADCs, and GPIOs on a single chip. The Cortex-M0+ core, licensed by ARM, is a low-gate-count 32-bit core optimized for energy-efficient embedded designs. Within the hierarchy ARM Cortex-M -> Cortex-M0+ -> SAM D21 family -> this part, the ATSAMD21J16B-MFT occupies the lower-memory tier designed for cost-sensitive applications. Key features include the 48 MHz Cortex-M0+ core delivering 2.46 CoreMark/MHz, full-speed USB 2.0 device/host support, a 12-bit ADC with up to 20 channels, SERCOM configurable serial interfaces, and a powerful peripheral touch controller (PTC). The device also offers a low-power RTC, six flexible SERCOM channels, and an event system for inter-peripheral signaling without CPU involvement. From an architecture perspective, the SAM D21 integrates a single-cycle hardware multiplier, a nested vectored interrupt controller (NVIC), and Microchip's SleepWalking peripheral logic that lets peripherals wake the CPU only when relevant events occur, dramatically reducing average power. The 64-QFN package exposes all major peripheral pins plus a dedicated USB transceiver interface. Typical applications include IoT sensor hubs, USB peripherals such as HID keyboards and CDC serial bridges, low-power wireless sensor nodes, industrial control front-ends, and consumer devices requiring capacitive touch user interfaces. The combination of USB, ADC, and SERCOM flexibility also suits wearable health monitors and battery-powered data loggers. When designing with the ATSAMD21J16B-MFT, plan for a 1.62V-3.63V supply and ensure the exposed pad on the QFN is soldered to a sufficiently large copper area for thermal dissipation. The Microchip ASF4/MPLAB Harmony 3 (now renamed MCC Melody) software framework provides drivers and middleware that simplify peripheral configuration. This page synthesizes distributor pricing snapshots, parametric cross-references, and design notes not aggregated on the manufacturer datasheet, giving engineers a single source to evaluate the ATSAMD21J16B-MFT against same-package drop-in alternatives in the SAMD20/SAMD21/L21 product family.

견적 요청 문의하기
ATSAMD21J16B-MU - 64KB Flash Cortex-M0+ MCU | Microchip 64-QFN
ATSAMD21J16B-MU

ATSAMD21J16B-MU - 64KB Flash Cortex-M0+ MCU | Microchip 64-QFN

The Microchip Technology ATSAMD21J16B-MU is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D21 family, featuring 64KB Flash, 8KB SRAM, and operating up to 48MHz. It is housed in a 64-pin QFN (9x9 mm) package with an exposed thermal pad and is rated for the industrial temperature range of -40C to +85C. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals such as timers, ADCs, communication interfaces, and GPIO. The ARM Cortex-M0+ is the smallest and most energy-efficient ARM processor core, designed for embedded applications that prioritize low power consumption and deterministic real-time response. Within the broader taxonomy, the SAM D21 sits at the intersection of MCU -> 32-bit MCU -> ARM Cortex-M MCU -> low-power MCU -> Microchip SAM D family, and the ATSAMD21J16B is the 64KB Flash variant within the SAM D21J 64-pin sub-family. Key features include the Cortex-M0+ core delivering 2.46 CoreMark/MHz, full-speed USB 2.0 device/host support, a 12-bit 1 MSPS ADC, two I2C, up to six SERCOM (configurable serial communication), and advanced low-power Idle/Standby sleep modes with SleepWalking peripherals. The device also integrates a 12-channel DMAC, a 12-channel Event System, and a 48MHz DFLL locked to a 32.768kHz crystal for accurate USB timing. The 64-QFN package with EPAD provides a low-thermal-resistance path to the PCB copper pour, enabling sustained 48MHz operation in thermally constrained industrial enclosures. The SAM D21 family is drop-in compatible with the SAM D20 family, simplifying migration from lower-pin-count or smaller-Flash designs. The 64KB Flash variant (J16) is positioned for cost-sensitive connected designs that need USB, more serial channels, or a richer analog front end than the J15 (32KB) variant. With its combination of low power, USB, and Cortex-M0+ performance, the ATSAMD21J16B-MU targets IoT sensor nodes, consumer USB peripherals, and industrial control modules.

견적 요청 문의하기
ATSAMD21J16B-MUT - 48MHz Cortex-M0+ 64KB Flash MCU | Microchip
ATSAMD21J16B-MUT

ATSAMD21J16B-MUT - 48MHz Cortex-M0+ 64KB Flash MCU | Microchip

The Microchip Technology ATSAMD21J16B-MUT is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D21J family, featuring 64KB of Flash and 8KB of SRAM in a 64-pin QFN (9x9 mm) package. It operates at a maximum CPU frequency of 48 MHz and reaches 2.46 CoreMark/MHz, targeting low-power embedded applications across industrial and consumer segments. The device supports 1.62V to 3.63V operating voltage and integrates advanced peripherals including a 12-channel DMA controller and 12-channel Event System for energy-efficient peripheral coupling. A 32-bit microcontroller (MCU) is an embedded computing device that integrates a CPU core, program memory (Flash), working memory (SRAM), and a rich set of peripherals on a single silicon die. The ARM Cortex-M0+ is the most energy-efficient ARM processor core, designed for deterministic real-time control and ultra-low power operation. The SAM D21 family positions itself between 8-bit/16-bit MCUs (PIC16, STM8) and higher-end Cortex-M3/M4 parts, balancing cost, power, and computational throughput. Key features include 64KB Flash, 8KB SRAM, 48 MHz CPU, integrated Full-Speed USB 2.0 device, and up to 6 SERCOM (serial communication) interfaces configurable as I2C/SPI/UART. The SAM D21J series offers 64-pin QFN and 64-pin TQFP package options with up to 52 GPIO pins, supporting multiple package variants within the same family for design flexibility. Functional Safety (FuSa) variants are available for safety-critical applications requiring IEC 61508 SIL capability. Architecturally, the ATSAMD21J16B uses a single-cycle I/O bus (IOBUS) and peripheral event system that allows peripherals to communicate without CPU intervention, dramatically reducing active-mode power consumption. SleepWalking peripherals can wake the CPU only when needed, enabling deep sleep currents below 10 uA. The integrated DFLL48M digital frequency-locked loop provides high-accuracy 48 MHz USB operation directly from a low-power 32.768 kHz crystal. Typical applications include IoT sensor nodes, USB human-interface devices (HID), industrial control modules, smart home gateways, and battery-powered wearable electronics. The combination of Full-Speed USB, low-power modes, and small QFN footprint makes it especially suited for compact USB-powered devices. When designing with this part, note the MUT suffix indicates Tape & Reel packaging, industrial temperature grade (-40C to +85C), and 3.3V nominal supply. PCB layout should keep the decoupling network (typically 100 nF + 4.7 uF) within 3 mm of the VDD pins to maintain signal integrity on the high-speed USB data lines. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet, providing engineers with a one-stop reference for component selection, sourcing, and PCB implementation.

견적 요청 문의하기
ATSAMD21J17A-AF - 48MHz Cortex-M0+ MCU, 128KB Flash, USB | Microchip
ATSAMD21J17A-AF

ATSAMD21J17A-AF - 48MHz Cortex-M0+ MCU, 128KB Flash, USB | Microchip

The Microchip Technology ATSAMD21J17A-AF is a 32-bit ARM Cortex-M0+ flash microcontroller operating up to 48 MHz, integrating 128 KB of Flash and 16 KB of SRAM in a 64-pin TQFP (10x10 mm) package. Part of the SAM D21J family, it combines a single-cycle hardware multiplier, a full-speed USB 2.0 device controller with on-chip transceiver, six configurable SERCOM modules, a 12-bit 350 ksps ADC, and a 10-bit 350 ksps DAC. An MCU (microcontroller) is a single-chip computer integrating a CPU core, program and data memory, and configurable peripherals on one silicon die. The ARM Cortex-M0+ is the most energy-efficient ARM processor core for embedded applications, and Microchip's SAM D21 family extends the Cortex-M0+ with a dedicated event system, SERCOM peripherals, and a SleepWalking power-management architecture. The 'J' suffix denotes the high-pin-count 64-pin variant, providing maximum GPIO and peripheral accessibility versus the 'G' (48-pin) and 'E' (32-pin) siblings. Key differentiating specifications include 128 KB of Flash with 4 KB of read-while-write (RWW) EEPROM emulation, six SERCOM channels each independently configurable as I2C, SPI, or USART, an integrated USB 2.0 Full-Speed device with on-chip transceiver, and an operating voltage range of 1.62 V to 3.63 V. The 12-bit ADC offers up to 20 analog input channels with hardware oversampling, and the device achieves 2.46 CoreMark/MHz, delivering ~118 CoreMark at maximum clock. Industrial temperature range is -40C to +125C. Architecturally, the SAM D21 family uses a single AHB/APB bus matrix with a separate bridge for the SERCOM modules, enabling deterministic DMA-driven I/O. The SleepWalking event system allows peripherals to wake the core only on relevant events, dramatically reducing active-mode current in battery-powered applications where quiescent draw dominates. The integrated USB PHY eliminates external transceiver circuitry, saving BOM cost and PCB area in HID, CDC, and composite-USB designs. Typical applications include USB Human Interface Devices, home automation gateways, low-power wireless sensor nodes, smart metering, industrial control panels, and consumer wearables. The integrated USB device controller and rich SERCOM set simplify designs requiring multiple serial protocols without external glue logic, and the 4 KB RWW EEPROM area is well-suited to data logging applications requiring non-volatile parameter storage without an external EEPROM chip. When designing with this device, allocate the 128 KB Flash carefully: approximately 8 KB is consumed by the SAM D21 bootloader, leaving ~120 KB for application code. Use Atmel Studio 7, MPLAB X IDE, or MPLAB Harmony 3 with the START code-configurator for peripheral initialization, and budget quiescent current carefully: full Sleep mode draws under 10 uA, but active peripherals can dominate consumption. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

견적 요청 문의하기
ATSAMD21J17A-AU - 48MHz Cortex-M0+ 128KB MCU 64-TQFP | Microchip
ATSAMD21J17A-AU

ATSAMD21J17A-AU - 48MHz Cortex-M0+ 128KB MCU 64-TQFP | Microchip

The Microchip Technology ATSAMD21J17A-AU is a 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D21J family, delivering 48 MHz CPU performance with 128 KB of Flash and 16 KB of SRAM in a 64-pin TQFP (10x10 mm) package. Operating from a 1.62 V to 3.6 V supply, it integrates a full peripheral set including SERCOM, USB, ADC, DAC, and event system for connected embedded designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and peripherals onto one die. Within the embedded hierarchy, an MCU sits below microprocessors in computational capability but above basic logic ICs in functional density, providing self-sufficient intelligence for sensors, actuators, and human-interface subsystems. The Cortex-M0+ is ARM's smallest and most energy-efficient application processor core, optimised for deterministic interrupt response and low active/idle power. Microchip's SAM D21 family extends this core with Microchip-proprietary analog and timer IP, producing parts that compete head-to-head with STM32L0, EFM32, and NXP Kinetis KE series for ultra-low-power IoT sockets. Key features include 48 MHz Cortex-M0+ core with single-cycle multiplier, 128 KB Flash plus 16 KB SRAM, full-speed USB 2.0 Device with on-the-go (OTG) support, up to six SERCOM configurable serial interfaces, 12-bit 1 MSPS ADC, 10-bit DAC, 5 timers/counters, two I2S interfaces, and a peripheral event system that allows peripherals to interact without CPU wakeup. The 64-pin TQFP footprint exposes 52 GPIO with 8 analog-capable pins, suiting boards that need USB, multiple UART/SPI/I2C buses, and motor-control PWM in parallel. The SAM D21 architecture uses a separate AHB peripheral bus and a peripheral event fabric that lets SERCOM, ADC and timer blocks trigger one another in hardware, offloading the Cortex-M0+ core. The on-chip USB 2.0 Full-Speed transceiver and PHY eliminate external crystals for low-speed USB, and a 32 kHz internal RTC oscillator reduces BOM cost for battery-powered designs. Sampled in the SAM D21 datasheet, an LDO plus DC-DC SleepWalking power path enables measured run currents of a few mA at 48 MHz and sub-µA sleep currents. Typical applications include consumer wearables, smart-home sensor hubs, USB HID peripherals, low-power wireless nodes, industrial metering and home-automation gateways. The 64-pin TQFP gives enough peripheral headroom for 4-wire SPI displays plus an SD card interface, and the AES engine supports secure firmware updates. When designing with this MCU, ensure the 64-pin TQFP pad geometry matches the standard SAM D20/D21/DA1 land pattern so code written for one part can be ported across the family without PCB rework. Decoupling VDDIN with 100 nF + 1 µF and reserving a 32.768 kHz crystal footprint is recommended practice across the family. This page consolidates live DigiKey/Mouser stock, drop-in compatible family variants, and practical design notes that the manufacturer datasheet alone does not present.

견적 요청 문의하기
ATSAMD21J17A-AUT - SAM D21 Cortex-M0+ 48MHz MCU | Microchip
ATSAMD21J17A-AUT

ATSAMD21J17A-AUT - SAM D21 Cortex-M0+ 48MHz MCU | Microchip

The Microchip Technology ATSAMD21J17A-AUT is an ARM Cortex-M0+ based 32-bit flash microcontroller from the SAM D21 family, delivering 48 MHz CPU performance with 128 KB Flash and 16 KB SRAM in a 64-pin TQFP (10x10 mm) package. As an automotive-qualified ("-AUT" suffix) part, it targets functional-safety capable applications in harsh environments while retaining the same peripheral set as the industrial-grade ATSAMD21J17A-AU variant. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash), data memory (SRAM), and integrated peripherals such as timers, communication interfaces, and analog blocks. ARM Cortex-M0+ cores specifically target ultra-low-power embedded applications: they use the Thumb-2 instruction subset, offer single-cycle GPIO access, and integrate sleep modes that allow deep power-down while still waking on peripheral events. The SAM D21 family sits within Microchip's broader hierarchy of 8-bit PIC -> 16-bit PIC24 -> 32-bit SAM ARM Cortex-M microcontrollers, and is the company's M0+ flagship for consumer and industrial IoT. Key features of the ATSAMD21J17A-AUT include up to 6 SERCOM (serial communication) interfaces configurable as I2C/SPI/UART, a 12-bit ADC with up to 20 channels, a 10-bit DAC, four 16-bit Timer/Counters, a 32-bit RTC, and a full-speed USB 2.0 device/host interface. The device operates from 1.6 V to 3.6 V and integrates an on-chip voltage regulator that simplifies single-rail designs. Hardware touch support (PTC) and a configurable Event System let designers route peripheral triggers without CPU intervention, reducing latency and power. Architecturally, the SAM D21 uses a Harvard bus with separate AHB and APB bridges, allowing simultaneous Flash fetch and DMA transfer. The Cortex-M0+ core pairs with a Nested Vectored Interrupt Controller (NVIC) and a Wake-up Interrupt Controller (WIC) so deep-sleep currents remain in the microampere range. Advanced analog (ADC, DAC, comparators) and motor-control timers are inherited from Atmel's M0+ heritage, giving designers access to high-performance mixed-signal capability on a low-power core. Typical applications include home automation endpoints, smart metering, consumer wearables, industrial sensor hubs, USB HID peripherals, and automotive body-electronics modules where -AUT grade is required. The wide SERCOM count (six) makes the part attractive for bridge designs that must speak multiple protocols (e.g., SPI sensor + I2C display + UART debug). A key design consideration is the package pin-out: the 64-pin TQFP exposes 52 GPIO, leaving ample headroom for both functional pins and breadboard-friendly breakout. Ensure your PCB layout respects Microchip's recommended decoupling (100 nF + 4.7 uF bulk near VDDIN) and that the VDDCORE pin is left floating only if using the internal regulator (the default for VDDIN > 2.0 V). This page synthesizes current distributor pricing, automotive-grade qualification, and drop-in alternatives in the SAM D21 family that engineers may not find in the standalone datasheet PDF.

견적 요청 문의하기
ATSAMD21J17A-CUT - SAM D21J Cortex-M0+ MCU 128KB Flash | Microchip
ATSAMD21J17A-CUT

ATSAMD21J17A-CUT - SAM D21J Cortex-M0+ MCU 128KB Flash | Microchip

The Microchip Technology (formerly Atmel) ATSAMD21J17A-CUT is a 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D21J family, delivering 48 MHz CPU performance with 128 KB of embedded Flash and 16 KB of SRAM in a 64-ball UFBGA (5x5 mm) package. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and a rich set of peripherals. The SAM D21 family belongs to the broader category of low-power ARM Cortex-M0+ microcontrollers, positioned between 8-bit AVR/PIC microcontrollers and higher-performance Cortex-M4/M7 parts. It serves as the brain of embedded systems requiring deterministic real-time control with low energy consumption. Key features of this device include a 48 MHz Cortex-M0+ core reaching 2.46 CoreMark/MHz, Full-Speed USB 2.0 with on-chip transceiver, a 12-bit 350 ksps ADC with up to 20 channels, two analog comparators, a 10-bit DAC, up to six SERCOM configurable serial communication peripherals, an Event System for inter-peripheral signaling, and a Peripheral Touch Controller (PTC) supporting capacitive touch sensing. The device operates from 1.62V to 3.63V across the industrial -40C to +85C temperature range. The SAM D21 architecture combines a high-performance 32-bit core with Microchip's SleepWalking technology, enabling peripherals to wake the core only on relevant events while consuming only a few microamperes. The integrated USB 2.0 Full-Speed transceiver eliminates external PHY chips, reducing BOM cost for connected consumer and industrial products. Hardware cryptographic support includes AES-256 and True Random Number Generator (TRNG) blocks. Typical applications include home automation gateways, smart consumer appliances, IoT sensor nodes, industrial metering, HVAC controllers, USB HID peripherals (keyboards, mice, custom HID), wearable health monitors, and capacitive touch human-machine interfaces. The combination of USB, capacitive touch, and rich analog peripherals makes this MCU especially well-suited to products that must communicate with hosts and interact with users. Designers should budget adequate PCB area for the 64-ball UFBGA 5x5 mm footprint, which requires sub-0.5 mm pitch fanout routing. For new designs, evaluate the ATSAMD21J17A-AUT TQFP-64 variant for easier prototyping and hand-rework, since BGA packages require X-ray inspection. Decoupling capacitors should be placed within 3 mm of all supply pins with a 4.7 uF bulk plus 100 nF ceramic combination. This page consolidates distributor stock, parametric drop-in alternatives, and practical design notes that complement the manufacturer datasheet.

견적 요청 문의하기
ATSAMD21J17A-MF - 48MHz Cortex-M0+ MCU 128KB Flash | Microchip
ATSAMD21J17A-MF

ATSAMD21J17A-MF - 48MHz Cortex-M0+ MCU 128KB Flash | Microchip

The Microchip Technology ATSAMD21J17A-MF is a 32-bit ARM Cortex-M0+ microcontroller operating at up to 48 MHz, equipped with 128 KB of Flash and 16 KB of SRAM, housed in a 64-pin QFN (9x9 mm) package with an exposed thermal pad. It belongs to the SAM D21J family and integrates Functional Safety (FuSa) features, making it suitable for safety-critical consumer, industrial, and metering applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and a rich set of peripherals such as timers, communication controllers, and analog blocks. The Cortex-M0+ core is the smallest and most energy-efficient member of the ARM Cortex-M processor family, designed for deterministic real-time control in cost- and power-sensitive embedded systems. Within the broader semiconductor hierarchy, the SAM D21J sits in the category: 32-bit microcontroller -> ARM Cortex-M0+ MCU -> low-power MCU -> embedded processor -> semiconductor IC. Key features include 128 KB Flash with 4 KB read-while-write (RWW) section, 16 KB SRAM, full-speed USB 2.0 Device/Host with on-chip transceiver, up to six SERCOM (serial communication) interfaces supporting I2C, SPI, and UART, a 12-bit 350 ksps ADC, a 10-bit 350 ksps DAC, and two analog comparators. The device operates from 1.62 V to 3.63 V and supports industrial temperature grade (-40C to +125C). Architecture-wise, the SAM D21J combines an event-driven peripheral system (EVSYS) with DMA-driven SERCOM channels, allowing the CPU to remain in sleep modes while peripherals service asynchronous events. This contributes to the family's low active-power figure of around 70 uA/MHz and sleep currents below 5 uA with full SRAM retention. The integrated USB 2.0 Full-Speed transceiver eliminates external PHY cost and simplifies USB device designs. Typical applications include home-automation hubs, smart metering, industrial sensor nodes, USB human-interface devices (HIDs), consumer appliances, and wearable controllers. Its AEC-Q100 qualification (per Hotenda's listing for this part number) extends suitability into automotive body and chassis subsystems. When designing, ensure that the exposed pad on the QFN-64 is soldered to a sufficiently large copper pour to meet the 31.4 C/W theta_JA thermal budget, and place the 32.768 kHz crystal traces short and guarded for low-jitter RTC operation. This page consolidates distributor pricing, same-family SAM D20/D21 alternatives, and practical design guidance beyond what the manufacturer datasheet provides alone.

견적 요청 문의하기
ATSAMD21J17A-MU - ARM Cortex-M0+ MCU 128KB Flash | Microchip
ATSAMD21J17A-MU

ATSAMD21J17A-MU - ARM Cortex-M0+ MCU 128KB Flash | Microchip

The Microchip Technology ATSAMD21J17A-MU is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D21J family, featuring 128KB of Flash, 16KB of SRAM, and a maximum CPU frequency of 48 MHz, housed in a 64-pin QFN (9x9 mm) package with an operating voltage range of 1.62V to 3.6V. The device integrates a full-speed USB 2.0 interface with on-the-go (OTG) support, a 12-bit ADC, a 10-bit DAC, and multiple SERCOM (serial communication) interfaces. What is an ARM Cortex-M0+ microcontroller? An ARM Cortex-M0+ microcontroller is a low-power, 32-bit microcontroller core designed for embedded applications that require energy efficiency, deterministic interrupt handling, and a small footprint. As part of the broader ARM Cortex-M family, Cortex-M0+ parts sit below Cortex-M3/M4/M7 in performance but above 8-bit legacy MCUs in capability, making them a common choice for IoT sensors, consumer appliances, and battery-powered devices. The ATSAMD21J17A-MU sits within the voltage regulator (power management) hierarchy adjacent to its built-in DC-DC converter and POR (power-on reset) subsystems. Key features include a peripheral touch controller supporting up to 256 channels, a 32-bit real-time clock and calendar (RTC), a 32-bit hardware CRC, and a full-speed USB 2.0 Device/Host controller. The device also provides a 6-channel event system, multiple timers/counters (TC), and a capacitive touch acquisition interface (PTC), enabling human-interface applications such as touch buttons, sliders, and proximity sensing. The ATSAMD21J17A-MU uses a single-cycle hardware multiplier and a 2-stage pipeline to deliver up to 2.46 CoreMark/MHz at 48 MHz. Its SleepWalking peripherals and Event System let the CPU remain in deep sleep while peripherals continue to monitor inputs, achieving typical active current around 7 mA at full speed and standby current below 5 microamps with RTC retention. Typical applications include low-power IoT sensor nodes, USB HID peripherals (keyboards, mice, custom input devices), home automation controllers, consumer appliances, and industrial metering. The integrated USB, capacitive touch, and rich serial peripherals make it suitable as a single-chip solution that avoids external bridge ICs. When designing with this device, pay attention to the QFN thermal pad connection and follow Microchip's recommended PCB layout for the 9x9 mm 64-QFN. The integrated DC-DC converter requires an external inductor and capacitors as detailed in the SAM D21 datasheet. Firmware development is supported by Microchip Studio (formerly Atmel Studio) and the MPLAB Harmony v3 framework. This page synthesizes distributor pricing from DigiKey, Mouser, Octopart, and LCSC, drop-in alternatives from the SAM D21 family, and practical design notes drawn from the Microchip SAM D21 datasheet family - information not consolidated on any single manufacturer or distributor page.

견적 요청 문의하기
ATSAMD21J17A-MUT - 48MHz Cortex-M0+ MCU, 128KB Flash | Microchip
ATSAMD21J17A-MUT

ATSAMD21J17A-MUT - 48MHz Cortex-M0+ MCU, 128KB Flash | Microchip

The Microchip ATSAMD21J17A-MUT is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D21J family, delivering 48 MHz CPU performance with 128 KB Flash and 16 KB SRAM in a 64-pin QFN (9x9 mm) package. It features the SERCOM serial-communication engine, a 12-bit DAC, a 14-channel 20-channel-capable event system, and Full-Speed USB with on-chip transceiver, all powered by 1.62 V to 3.63 V supply. What is a Cortex-M0+ microcontroller? An ARM Cortex-M0+ MCU is an ultra-low-power 32-bit processor core designed by ARM Holdings for embedded systems, featuring the Thumb-2 instruction set, a single-cycle I/O port, and a Micro Trace Buffer. It sits within the broader taxonomy of MCU -> embedded microcontroller -> semiconductor device, and is typically deployed where deterministic real-time response, low active/standby power, and rich connectivity peripherals are required. Key differentiating features of the ATSAMD21J17A-MUT include 6 SERCOM modules (each configurable as UART/SPI/I2C), a 12-bit 350 ksps ADC with up to 14 analog channels, 2 analog comparators, a real-time clock with calendar mode, and a built-in Full-Speed USB 2.0 Device/Host controller with internal pull-up. The SAM D21J also carries Microchip Functional Safety (FuSa) documentation, simplifying IEC 60730 class B compliance for home appliances. The integrated Cortex-M0+ core reaches 2.46 CoreMark/MHz, giving roughly 118 CoreMark total throughput at maximum clock. Architecturally, the device uses a single-cycle hardware multiplier, single-cycle I/O port, and a tightly-coupled peripheral bridge that links SERCOM, ADC, DAC, timers, and USB to the AHB/APB bus matrix. The 128 KB dual-bank Flash supports read-while-write (RWW) operation against 4 KB RWW section, allowing live firmware updates without halting the application. The Event System interconnects peripherals without CPU intervention, reducing wake events and saving power. Typical applications include home automation controllers (thermostats, smart plugs, sensor hubs), consumer electronics (wearables, fitness bands, BLE bridges), metering (utility meters, energy monitors), industrial sensor nodes, USB HID peripherals (keyboards, mice, custom HID), and low-power IoT end-node devices. The wide operating voltage and rich SERCOM count make it well-suited for battery-powered designs with multiple radio or sensor interfaces. Design consideration: route the USB DP/DM traces as a 90-ohm differential pair and place the decoupling capacitor network (1 uF + 100 nF) within 2 mm of the VDDCORE pin to maintain signal integrity and core stability. For battery applications, leverage the integrated buck-boost converter with a 1 uH inductor to maximise efficiency at light loads. This page synthesises distributor pricing from DigiKey/Mouser/LCSC, drop-in alternatives within the SAM D21J family, and practical design notes that go beyond the manufacturer datasheet.

견적 요청 문의하기
ATSAMD21J17D-AF - ARM Cortex-M0+ 48MHz MCU, 128KB Flash, TQFP-64 | Microchip
ATSAMD21J17D-AF

ATSAMD21J17D-AF - ARM Cortex-M0+ 48MHz MCU, 128KB Flash, TQFP-64 | Microchip

The Microchip Technology ATSAMD21J17D-AF is a low-power, high-performance ARM Cortex-M0+ based flash microcontroller in a 64-pin TQFP (10x10 mm) package with extended 125°C temperature rating. It operates at up to 48 MHz, integrates 128 KB of Flash and 16 KB of SRAM, and includes a full-speed USB 2.0 device interface plus a 12-bit ADC, 10-bit DAC, and SERCOM peripheral set. The device targets home automation, consumer, metering, and industrial applications where low power and integrated peripherals matter most. The ARM Cortex-M0+ is the smallest and most energy-efficient member of the Cortex-M family, designed for deeply embedded 8/16-bit replacement workloads. A microcontroller (MCU) integrates a CPU core, non-volatile program memory (Flash), volatile working memory (SRAM), and a mix of analog and digital peripherals onto a single die. Compared with classic 8051 or PIC microcontrollers, Cortex-M0+ parts deliver a modern 32-bit Thumb-2 instruction set, deterministic nested-vector interrupts, and a vendor-neutral AMBA peripheral bus, while retaining ultra-low standby current. The SAMD21 family specifically adds Microchip's Event System (inter-peripheral signalling without CPU wake) and SleepWalking peripherals that remain clocked while the core sleeps. Key specifications of the ATSAMD21J17D-AF include 48 MHz maximum CPU clock, 128 KB Flash with 4 KB read-while-write region, 16 KB SRAM, six SERCOM channels configurable as UART/SPI/I2C, one full-speed USB 2.0 device port, up to 6 communication interfaces, and up to 52 programmable I/O pins. The integrated 12-bit ADC delivers up to 350 ksps, the 10-bit DAC up to 350 ksps, and the peripheral event system supports 12 channels. Operating voltage spans 1.62 V to 3.63 V with multiple low-power sleep modes down to sub-microamp standby. Architecturally, the ATSAMD21J17D-AF uses a single-cycle hardware multiplier, separate Flash and SRAM AHB-Lite buses, and a peripheral bridge that decouples SERCOM and event traffic from the CPU. The Full-Speed USB device controller includes an on-chip transceiver and internal pull-up, eliminating external components for HID, CDC, or vendor-class USB applications. The integrated SERCOM blocks can be reassigned at runtime, providing design flexibility when moving pins between UART, SPI, and I2C. Typical applications include home automation controllers (Zigbee/Matter bridges, smart thermostats), consumer products (USB HID peripherals, wearables), metering (gas/water/electricity counters with LCD), and industrial sensor hubs (Modbus nodes, 4-20 mA loop replacements). The extended 125°C temperature rating also supports automotive aftermarket and outdoor industrial use cases. When designing with this MCU, allocate at least one SERCOM channel for UART debug console, plan the USB DP/DN trace impedance for 90 ohm differential, and use the Event System to wake the CPU on peripheral triggers instead of polling. The 128 KB Flash and 16 KB SRAM are sufficient for an RTOS kernel plus an application, but compiler -Os and a memory pool allocator are recommended for production builds.

견적 요청 문의하기