IC Penguat
Produk (1,100+)
TDF8546TH/N2 - 4x45W BTL Class-AB Car Audio Amplifier | NXP
The NXP TDF8546TH/N2 is an I2C-bus controlled, quad Bridge-Tied Load (BTL) Class-AB automotive audio power amplifier delivering 4 x 45 W into 4 Ω in the 36-pin HSOP (Heatsink Small Outline Package) with exposed thermal pad. It is intended for head-unit and external amplifier applications in 12 V vehicles, with full I2C diagnostics, start-up diagnostics, and best-efficiency switching modes for reduced dissipation during low-to-medium output. What is a quad BTL Class-AB automotive amplifier? A BTL (Bridge-Tied Load) audio amplifier drives each speaker differentially across two outputs, doubling the voltage across the load and quadrupling the achievable output power versus a single-ended topology for a given supply rail. The Class-AB output stage combines bipolar output transistors biased to minimize crossover distortion while preserving high efficiency at moderate output levels, making it the long-standing industry choice for in-vehicle audio. NXP's TDF family falls within the broader power management / amplifier IC hierarchy: Audio Amplifier -> Class-AB Amplifier -> Automotive Audio Amplifier -> Power Management IC -> Semiconductor. Key features of the TDF8546 include operation from a battery supply as low as 6 V (suited to stop/start vehicles), best-efficiency mode that dynamically adjusts output stage biasing, full I2C-bus controlled diagnostics including start-up and runtime load diagnostics, and independent channel gain control. The integrated thermal foldback and over-current protection safeguard the exposed pad / the top-side body of the HSOP package, which is itself the primary heat-dissipation path. The device uses a complementary bipolar output architecture with on-chip gate drivers and charge-pump generation for the high-side NPN transistors, eliminating the need for external bootstrap capacitors. I2C control permits mode switching, mute/unmute, and read-back of diagnostic flags from the host microcontroller, simplifying ECU software development. Typical applications include automotive head units and infotainment amplifiers, external booster amplifiers for premium sound systems, and stop/start-compliant audio platforms where cranking dips below 8 V are common. The combination of best-efficiency operation and low quiescent current helps meet stringent vehicle standby-current budgets. When designing with this part, ensure the HSOP exposed thermal pad is soldered to a copper area of at least 6 cm² for full 4 x 45 W output. Use low-ESR electrolytic bypass capacitors within 10 mm of the supply pins, and keep the I2C lines away from the output traces to avoid coupling. Consider heatsink attachment for sustained high-output operation. This page synthesizes distributor pricing, end-of-life status, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
TFA9865 - 7W CoolPWM Smart Class-D Amplifier | Goodix
The Goodix TFA9865 is a high-performance, fully digital Class-D smart audio amplifier delivering 7 W peak output power with an ultra-low noise floor below 7 uV, housed in an extremely compact 2.2x2.2 mm WLCSP package. It targets mobile and portable audio applications where board area, quiescent power, and acoustic clarity are simultaneously critical design constraints. A Class-D audio amplifier is a switching-mode power stage that converts a PWM or PDM waveform into a high-efficiency audio output, driving a loudspeaker directly through an LC reconstruction filter. Within the broader audio IC taxonomy, the TFA9865 sits in the smart amplifier sub-category of power management and signal chain ICs, sitting alongside traditional Class-AB amplifiers but achieving far higher efficiency (typically >85 %) and lower thermal dissipation. Goodix's first-generation CoolPWM architecture is a proprietary, fully digital modulation scheme that breaks away from conventional Class-D topologies to minimize EMI and audible idle-channel noise. Key specifications include 7 W peak output into a typical 4 ohm or 8 ohm speaker load, an idle-channel noise floor of less than 7 uV, integrated DSP-based speaker protection algorithms, I2C/TDM control interface, and a small WLCSP footprint enabling direct placement adjacent to the smartphone or tablet speaker. Compared with discrete analog Class-D solutions, the TFA9865 reduces BOM count by integrating gate drivers, MOSFET power stage, and digital modulation in a single die. The CoolPWM digital architecture leverages advanced manufacturing processes to deliver high audio performance with very low power consumption. Built-in adaptive excursion control and thermal protection extend the usable loudness envelope of small speakers without causing voice-coil damage. This makes the device well suited to handset, tablet, and portable speaker applications where designers must push SPL limits within tight thermal budgets. Typical applications include smartphone and tablet loudspeaker amplification, portable Bluetooth speakers, wearable audio devices, and notebook/laptop speakers. The part is commonly paired with Goodix or third-party audio CODECs and digital microphone pre-processors to form a complete mobile audio playback chain. When designing with the TFA9865, pay close attention to PCB layout of the LC output filter, the placement of the bootstrap capacitor, and the thermal pad connection. Use a 4-layer stack-up with a solid ground plane directly beneath the part to minimize EMI coupling into adjacent RF circuits. This page synthesizes distributor pricing, drop-in alternatives, application examples, and practical design notes not found in the manufacturer product brief.
THS3061D - 300MHz High-Slew-Rate CFA | Texas Instruments
Texas Instruments THS3061D is a single, high-voltage, high-slew-rate current-feedback amplifier with a 300 MHz unity-gain bandwidth, 7000 V/us slew rate, and 8-pin SOIC package. The device is designed for low-distortion, large-signal amplification and uses Texas Instruments BICOM-1 process technology. A current-feedback amplifier, or CFA, is an analog amplifier architecture that uses feedback through an inverting input and offers high bandwidth and slew-rate performance for demanding signal chains. In the broader hierarchy, it belongs to the operational-amplifier family and the broader analog integrated-circuit category. Unlike a voltage-feedback amplifier, its bandwidth behavior depends strongly on the selected feedback resistor and gain setting. The supplied data identifies a 300 MHz unity-gain bandwidth, 120 MHz 0.1 dB bandwidth at a gain of 2, 7000 V/us slew rate at 10 MHz, and approximately -81 dBc third-order distortion. It also identifies ±145 mA output current into 50 ohm. These characteristics make the THS3061D suitable for video line drivers, VDSL line drivers, and other applications requiring large, linear output signals. The amplifier uses a current-feedback architecture rather than a conventional voltage-feedback input stage. In a typical implementation, the feedback network and input termination must be selected according to the manufacturer datasheet and the desired gain. The high slew rate can preserve large-signal amplitude in video and communication systems, while low distortion helps reduce signal degradation through the output stage. THS3061D is supplied in an 8-pin SOIC package and is specified for an operating temperature range of -40°C to +85°C in the supplied product data. The product page identifies the D package as an 8-pin SOIC. The supplied distributor result reports an in-stock quantity of 6,240 pieces and a unit price of $12.3490, while current pricing and availability should be confirmed at purchase. This page combines verified manufacturer and distributor information, application guidance, design notes, and an explicit distinction between confirmed drop-in alternatives and unavailable alternatives. The THS3061D is therefore best approached as a high-speed, high-voltage current-feedback amplifier for linear video and line-driver signal paths.
THS3061DGN - 300MHz CFA, 7000V/us Slew Rate | Texas Instruments
The Texas Instruments THS3061DGN is a single high-voltage, high slew-rate current feedback amplifier delivering 300 MHz unity-gain bandwidth, 7000 V/us slew rate, and +/-145 mA output current into 50 ohms, housed in an 8-pin HVSSOP (DGN) package with PowerPAD thermal pad. A current feedback amplifier (CFA) is a type of high-speed operational amplifier whose architecture uses a low-impedance inverting input to achieve bandwidth that is largely independent of closed-loop gain. In the signal-chain hierarchy, the CFA sits within the amplifier IC family alongside voltage feedback op amps (VFA) and fully differential amplifiers, and is preferred where wide bandwidth and fast settling must be maintained without the gain-bandwidth product penalty of VFAs. Key features include 7000 V/us slew rate for large-signal high-frequency performance, 0.1 dB gain flatness bandwidth of 120 MHz at a gain of 2, low distortion of -81 dBc at 10 MHz, and high output drive of +/-145 mA into 50 ohm loads. These parameters suit the device for driving ADC inputs, coaxial cables, and other low-impedance loads directly. The THS3061 is fabricated on Texas Instruments' BICOM-1 complementary bipolar process, enabling high-voltage operation (up to +/-15 V class supplies) with high-speed performance. The current feedback topology keeps bandwidth relatively constant across gain settings, while the PowerPAD package provides a low thermal resistance path essential for high-output-current operation. Typical applications include pulse amplifiers, RF/IF signal chains, high-speed data acquisition front ends, video line drivers, and test-and-measurement signal sources. Design consideration: as a CFA, the feedback resistor value must be selected per the datasheet recommendations; lowering Rf to increase bandwidth can cause peaking and instability. Ensure proper PowerPAD soldering to the PCB ground plane for thermal performance. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
THS3061DGNR - 300MHz 7000V/us CFB Amplifier | Texas Instruments
The Texas Instruments THS3061DGNR is a single-channel, high-voltage, high-slew-rate current-feedback (CFB) amplifier delivering a 300 MHz unity-gain bandwidth, a 7000 V/us slew rate, and up to +/-145 mA of output current into a 50 ohm load, housed in an 8-pin HVSSOP (DGN) package with PowerPAD thermal pad. It operates from supplies up to +/-15 V (30 V total). A current-feedback amplifier is a type of high-speed operational amplifier whose bandwidth is largely independent of closed-loop gain, making it a member of the broader amplifier hierarchy: CFB amplifier -> high-speed op amp -> operational amplifier -> analog signal-conditioning IC. Unlike voltage-feedback amplifiers, CFAs use a low-impedance inverting input and a current-driven internal stage, which is what enables their exceptional slew rates. Key features of the THS3061 include a 0.1 dB flatness bandwidth of 120 MHz at a gain of 2, second-harmonic distortion of -81 dBc at 10 MHz, and high output drive current of +/-145 mA, per the TI datasheet. These specs suit applications that need both speed and signal swing into low impedances. The device is fabricated on the TI BICOM-1 complementary bipolar process, which underpins its combination of high breakdown voltage (up to 30 V total supply) and high-frequency performance. The PowerPAD HVSSOP-8 package provides a low thermal-impedance path to the PCB, essential when driving heavy loads at high frequency. Typical applications include high-voltage pulse and laser-diode drivers, ADC input drivers in test and measurement equipment, video and communications signal chains, and active probes requiring high slew rate with substantial output current. Design consideration: because this is a current-feedback amplifier, the feedback resistor value should be kept close to the datasheet-recommended range; increasing RF reduces bandwidth and stabilizes the loop, while decreasing it can cause peaking or oscillation. This page synthesizes distributor availability data, drop-in alternative analysis, and practical design notes not found in the manufacturer datasheet. Pricing references are as of 2026-09-13.
THS3062D - Dual 7000V/us High-Speed Amplifier | TI
The Texas Instruments THS3062D is a dual, high-voltage, high-slew-rate current-feedback amplifier with a 300 MHz unity-gain bandwidth, 120 MHz 0.1 dB bandwidth at a gain of 2, and a 7000 V/us slew rate, housed in an 8-pin SOIC package. Each amplifier supports a ±15 V power supply, equivalent to 30 V across the supply terminals, and can deliver ±145 mA into a 50 ohm load. A current-feedback operational amplifier is a voltage-amplifier architecture in which the feedback impedance and closed-loop gain determine bandwidth and stability. Current-feedback amplifiers belong to the operational-amplifier, analog-signal-conditioning, and semiconductor hierarchies. They are particularly useful when a system requires large output voltage swings, fast edge rates, low signal distortion, or driving terminated analog lines. The THS3062D combines several performance-critical characteristics. Its 300 MHz unity-gain bandwidth supports wideband signal amplification, while its 7000 V/us slew rate allows large-amplitude signals to change rapidly without immediately becoming slew-rate limited. The 120 MHz 0.1 dB bandwidth applies at a gain of 2, and the output-current capability of ±145 mA into 50 ohms provides useful drive for demanding loads. The dual configuration also allows two high-speed amplifier channels in one package. The THS3062 uses Texas Instruments BICOM-1 process technology. Because it is a current-feedback amplifier, closed-loop bandwidth and stability depend on the feedback network and gain setting rather than following the same closed-loop bandwidth behavior as a conventional voltage-feedback amplifier. Designers should therefore follow the manufacturer feedback-network recommendations and observe resistance and capacitance constraints around the inverting input. Typical uses include video line drivers, VDSL line drivers, instrumentation amplifiers, high-speed filter stages, waveform-driver circuits, and analog communications equipment. Its combination of high voltage swing, fast slew rate, and dual-channel integration is particularly appropriate when two wideband signals must be amplified without using separate single-channel packages. When laying out a THS3062D board, keep feedback components close to the relevant amplifier pins and minimize parasitic capacitance at the inverting input. Decoupling capacitors should be placed close to the supply pins, and the SOIC thermal limitations should be considered when operating near the maximum output current. This page combines manufacturer and distributor data with same-footprint amplifier alternatives, application guidance, and design considerations to provide practical information beyond a basic ordering-table summary.
THS3091D - 235MHz Current-Feedback Op Amp | Texas Instruments
Texas Instruments THS3091D is a single, high-voltage, low-distortion current-feedback operational amplifier with a 235 MHz gain-bandwidth product, 7300 V/us slew rate, and operation across a ±5 V to ±15 V supply range. The device is supplied in an 8-pin SOIC package and is intended for applications requiring large, linear output signals, including pin drivers, power-FET drivers, VDSL line drivers, and arbitrary waveform generators. A current-feedback operational amplifier is a voltage-input, current-output amplifier architecture whose closed-loop bandwidth is primarily controlled by the feedback resistor rather than by a single fixed gain-bandwidth product. In the THS3091D, this architecture supports high-speed operation while maintaining low distortion. The result is useful where conventional voltage-feedback amplifiers would require excessive gain, where signal amplitude and slew rate must remain accurate, or where a capacitive load must be driven through a carefully designed feedback network. Key features include a 235 MHz bandwidth, 7300 V/us slew rate, and a high-voltage capability covering ±5 V to ±15 V supplies. The current-feedback topology provides high speed without relying on a voltage-feedback gain-bandwidth relationship of the same form. Its low-distortion characteristic supports signal-chain designs in which waveform fidelity and amplitude linearity are more important than micropower operation or rail-to-rail input/output capability. The THS3091D is optimized for high-voltage, large-signal output stages. Its supply range permits bipolar or split-supply operation when the circuit requires an output centered around ground, while dual positive supplies can also be used when the signal and output are referenced above ground. Because it is a current-feedback device, feedback-resistor selection is central to achieving the intended bandwidth, gain, and stability rather than treating the feedback network as a passive gain-setting detail. Typical uses include semiconductor pin drivers, power-FET gate drivers, VDSL line-driver outputs, high-voltage arbitrary waveform generation, and instrumentation requiring wide-band signal amplification. In each case, the 235 MHz bandwidth and 7300 V/us slew rate provide the speed needed to preserve large-amplitude waveforms, while the low-distortion architecture helps maintain signal fidelity. The 8-pin SOIC package permits conventional surface-mount assembly. Designers should use the manufacturer datasheet for the complete pin assignment, recommended feedback values, output-current capability, input and output range, and stability constraints. The THS3091D is not a rail-to-rail input or output device, so input common-mode and output swing requirements must be checked against the selected supply voltages. Current-feedback amplifiers can be sensitive to feedback-component tolerances, parasitic capacitance, and capacitive loading. This page consolidates the verified THS3091D product data, lifecycle information, source links, and selection guidance. It also distinguishes the SOIC THS3091D from other package or orderable variants and records unavailable electrical details explicitly rather than inferring them from unrelated THS309x-family members.
THS3092D - Dual 160MHz High-Speed Amplifier | Texas Instruments
The Texas Instruments THS3092D is a dual high-voltage, low-distortion, high-speed current-feedback operational amplifier with 160 MHz bandwidth, 5700 V/µs slew rate, and operation from ±5 V to ±15 V, housed in an 8-pin SOIC package. It delivers two amplifiers per package and is designed for large, linear output swings into demanding loads. A current-feedback operational amplifier is a voltage-feedback amplifier variant whose closed-loop bandwidth and stability are shaped primarily by feedback resistance rather than by a fixed gain-setting capacitance. In the signal-chain hierarchy, the THS3092D belongs to the operational-amplifier, analog-amplifier, and broader semiconductor categories. Its current-feedback architecture is useful where high speed, large output voltage, and low distortion must coexist. Key verified characteristics include 160 MHz small-signal bandwidth, 5700 V/µs slew rate, ±5 V to ±15 V supply operation, 14 pA/√Hz noninverting current noise, 17 pA/√Hz inverting current noise, and 2 nV/√Hz voltage noise. The manufacturer datasheet also identifies low-distortion operation suited to high-voltage arbitrary-waveform driver applications. The device uses a dual amplifier configuration to support two independent signal paths or differential drive arrangements. Its current-feedback topology is particularly appropriate for video, communications, test-and-measurement, and power-driver interfaces where large output swings and fast transient response are required. Designers should still verify gain-bandwidth behavior, load capacitance, output-current limits, and stability for the selected feedback network. Typical applications include high-voltage arbitrary waveform generation, power FET and VDSL line driving, video-signal conditioning, instrumentation, and industrial control interfaces. The broad supply range permits operation from ±5 V through ±15 V, while the high-speed characteristics support fast edge rates and low-distortion signal transfer. A key design consideration is feedback-resistor selection. Because current-feedback amplifiers depend on the feedback impedance, use the manufacturer-recommended values and check the complete gain, bandwidth, and stability relationship for the target load. Decoupling, grounding, and output-stage protection also become important when driving capacitive or high-resistance loads. This page combines verified manufacturer and distributor information, practical application guidance, and explicit design trade-offs for engineers evaluating the THS3092D. It is intended to support component selection, circuit planning, and datasheet-driven review rather than replace the manufacturer datasheet.
THS3095D - High-Speed Current-Feedback Amplifier | Texas Instruments
Texas Instruments THS3095D is a single high-voltage, low-distortion, high-speed current-feedback operational amplifier with power-down capability, supplied in an 8-pin SOIC package. The device operates from ±5 V to ±16 V, supports a 6000 V/µs slew rate, and can deliver 310 mA output current. Its low-distortion architecture is intended for large, linear output signals and high-speed waveform applications. The THS3095D includes a power-down pin, PD, that places the amplifier in a low-power standby state and reduces quiescent current from 9.5 mA to 500 µA. The current-feedback operational amplifier is a voltage-feedback amplifier subtype optimized for high-speed signal chains where gain bandwidth and stability can be affected by feedback impedance. Unlike a conventional voltage-feedback amplifier, the THS3095D uses a current-feedback topology that supports high slew rate, broad bandwidth, and low distortion when driven with suitable feedback resistors. It is used where signals must be amplified with high amplitude and fidelity, including pin drivers, power-FET drivers, and arbitrary-waveform generators. Key features include a ±5 V to ±16 V supply range, 6000 V/µs slew rate, 310 mA output-current capability, and a dedicated power-down function. The power-down control can simplify power management in systems that need to disable the amplifier between active intervals. The wide supply range allows operation from split analog rails in communications, instrumentation, industrial, and test equipment. For high-voltage output applications, the THS3095D is designed to preserve signal quality while driving demanding loads. Its low-distortion current-feedback architecture is particularly useful for large-signal waveform generation, where slew rate and output-current capability determine how faithfully large voltage steps can be reproduced. The device is not intended as a general-purpose precision-voltage-feedback amplifier; design calculations should use the manufacturer data sheet for feedback-resistor selection and stability verification. Typical applications include arbitrary-waveform generators, pin and power-FET drivers, VDSL line-driver circuits, communication equipment, and high-speed instrumentation. The amplifier can be used where a high-voltage output swing and rapid transient response are more important than very low offset voltage. The 8-pin SOIC package makes the THS3095D suitable for conventional surface-mount PCB assembly. The primary design consideration is the power-down interface and the feedback network. Keep the power-down control signal electrically defined, place the feedback resistors close to the amplifier pins, and use short, low-inductance connections for high-speed output stages. Review the manufacturer application guidance before selecting resistor values or adding capacitive load to the output. This page combines verified manufacturer and distributor information with practical selection and design guidance.
THS3096D - Dual 160 MHz Current-Feedback Amplifier | Texas Instruments
Texas Instruments THS3096D is a dual, high-voltage, low-distortion current-feedback operational amplifier with power-down in a 14-pin SOIC package. The verified product data identifies it as a two-circuit current-feedback amplifier with a 160 MHz gain-bandwidth product, operating across a ±5 V to ±15 V supply range. Each amplifier includes a power-down control, allowing the device to enter a lower-power standby state when the output no longer needs to remain active. A current-feedback operational amplifier is a voltage-feedback amplifier subclass optimized for high-speed closed-loop gain stages. Unlike the dominant signal error of a conventional voltage-feedback amplifier, current-feedback amplifiers distribute distortion differently across frequency and gain. This makes them useful when a design must preserve low distortion while operating at high bandwidth, particularly with resistive feedback networks. The THS3096 family's main verified characteristics include dual-channel operation, 160 MHz bandwidth, a 14-SOIC package, and an extended operating-temperature range of -40°C to 85°C for the ordered THS3096D variant. The manufacturer identifies the devices as suitable for large linear output signals. The power-down feature adds an important system-level control: a system can reduce dissipation and disable the output path without removing the complete analog subsystem from the board. The THS3096D uses a current-feedback topology rather than the conventional voltage-feedback architecture used by many general-purpose op amps. Its two channels, wide supply range, and high operating bandwidth make it a candidate for analog signal-conditioning blocks that need substantial output swing and speed. Designers should still evaluate the exact gain, output-voltage, output-current, noise, and stability limits in the manufacturer datasheet before finalizing a circuit. Typical applications identified by Texas Instruments include power MOSFET and power-FET drivers, PIN-diode drivers, and VDSL line drivers. These applications benefit from the combination of wide supply capability, high speed, and low distortion. The dual-channel organization can also reduce board area when two related drive or signal-conditioning functions are required within the same system. The primary design consideration is that current-feedback amplifiers require appropriate feedback resistors and careful attention to board layout. Resistor values should follow the manufacturer's gain table rather than being copied directly from a voltage-feedback design. Ground, supply, and feedback paths should be short, and output-current demand must remain within the datasheet limits. This page consolidates verified manufacturer and distributor information, distinguishes documented characteristics from parameters requiring confirmation, and provides application, comparison, and design guidance beyond a basic distributor listing. Pricing reflects the available unit-price reference as of 2026-10-28, while unverified electrical details are explicitly marked for engineering review.
THS3201D - 1.8 GHz Current-Feedback Amplifier | Texas Instruments
The Texas Instruments THS3201D is a single current-feedback operational amplifier with a 1.8 GHz unity-gain bandwidth, a 10,500 V/µs slew rate, and an operating supply range of ±3.3 V to ±7.5 V. The device is packaged in an 8-pin SOIC for high-speed instrumentation, arbitrary waveform generation, and high-resolution or high-sample-rate analog-to-digital converter drive applications. A current-feedback amplifier is a voltage-input, current-output amplifier topology that commonly uses feedback resistors to establish gain. Unlike a conventional voltage-feedback amplifier, its closed-loop bandwidth can remain comparatively stable as feedback resistance changes, making the THS3201D suitable for demanding high-bandwidth signal chains. Within the broader semiconductor hierarchy, the THS3201D is an analog operational amplifier, then an amplifier IC, and finally a signal-chain IC. The principal performance features are its 1.8 GHz unity-gain bandwidth, 10,500 V/µs slew rate, and broad ±3.3 V to ±7.5 V supply range. These characteristics support fast edge generation and accurate amplification of high-frequency waveforms. The manufacturer datasheet also identifies low-distortion operation as a key benefit for arbitrary waveform drivers and high-resolution, high-sampling-rate ADC applications. The THS3201D combines wide supply flexibility with high-speed edge-rate capability. Its current-feedback architecture is particularly relevant when driving capacitive ADC inputs, where large input capacitance can otherwise reduce the effective bandwidth of a voltage-feedback amplifier. Designers must nevertheless evaluate gain-setting resistors, source and load impedances, PCB parasitics, and output-current requirements as a complete signal chain rather than relying only on headline bandwidth. Typical uses include arbitrary waveform generation, high-speed ADC input drivers, communications test equipment, and instrumentation requiring low distortion at high frequency. In these systems, the amplifier converts a source waveform into a sufficiently large, fast, and accurate signal to meet the driven device's input requirements. The SOIC-8 package also supports conventional surface-mount PCB assembly. The primary design consideration is gain configuration. A current-feedback amplifier generally uses separate input and feedback resistors, and their values influence bandwidth, noise, stability, and output drive. PCB layout should minimize trace capacitance and maintain short feedback paths. Decoupling capacitors should be positioned close to the supply pins, while output routing should avoid long traces or capacitive loads that could compromise stability. This product page combines the verified manufacturer specifications, distributor availability information, package details, pricing status, application guidance, and design considerations in one searchable reference. It also distinguishes confirmed device facts from parameters that require confirmation from the complete datasheet, avoiding unsupported assumptions about electrical characteristics that are not present in the supplied search record.
THS3202D - 2GHz Dual Current-Feedback Amplifier | Texas Instruments
The Texas Instruments THS3202D is a dual current-feedback amplifier with 2 GHz unity-gain bandwidth, a 9000 V/us slew rate, and dual amplifiers in an 8-SOIC package. Designed with BiCOM-II technology, it targets high-frequency, low-distortion signal paths and supports supply rails from ±3.3 V to ±7.5 V. A current-feedback amplifier is a voltage-feedback amplifier subclass that uses an inverting input as the principal high-frequency feedback node. Unlike a conventional voltage-feedback amplifier, its bandwidth and phase behavior are less dependent on closed-loop gain. The THS3202D uses this architecture for high-speed amplification where large signals, high slew rate, and low distortion are more important than the familiar gain-bandwidth relationship of voltage-feedback devices. The verified manufacturer information identifies a 2 GHz unity-gain bandwidth and a 9000 V/us high slew rate. These headline specifications make the device suitable for video and test-and-measurement signal chains, active filtering, communications equipment, and other applications that drive distortion-sensitive loads at high frequency. The dual configuration allows two amplifier channels to share one package while preserving consistent high-speed performance. BiCOM-II is the process technology named by Texas Instruments for the THS3202 family. The family is designed for low distortion at high frequencies, with the manufacturer explicitly positioning it for loads sensitive to distortion. Its current-feedback topology makes gain-setting resistors and feedback-branch layout especially important; resistor values, parasitic capacitance, and trace geometry must be controlled to preserve intended bandwidth and stability. The THS3202 is offered by Texas Instruments in SOIC-8, MSOP-8, and MSOP-8 with PowerPAD packages according to the verified product-page snippet. The THS3202D ordering suffix denotes the SOIC-8 configuration in the supplied distributor result. Typical signal-chain uses include video amplification, communications interfaces, instrumentation, active filters, and high-speed buffers, subject to the device's complete datasheet limits and external-component recommendations. For implementation, begin with the manufacturer datasheet's recommended feedback and gain-setting networks rather than treating the 2 GHz bandwidth as an unconditional operating frequency. Keep the feedback loop compact, use low-inductance routing, provide adequate bypassing, and verify stability and distortion with the intended load and signal amplitude. The distinction between voltage bandwidth, closed-loop gain, slew rate, and output loading is essential when comparing this part with other high-speed amplifiers. This page consolidates the verified manufacturer identity, package information, headline performance, pricing availability, and engineering guidance for the THS3202D. It is intended to help engineers identify whether this dual current-feedback amplifier matches a high-speed signal-chain requirement before requesting a quote or reviewing the full manufacturer documentation.
THS4031 - 100MHz 1.6nV Low-Noise Op Amp | Texas Instruments
The Texas Instruments THS4031 is a single-channel, ultra-low voltage noise, high-speed voltage feedback amplifier delivering a 100-MHz bandwidth at gain of 2, a 100-V/us slew rate, and a 60-ns settling time (0.1%). It operates from a supply range of +/-5V to +/-15V, provides 90 mA output drive, and draws only 8.5-mA supply current per channel, in an 8-pin HVSSOP (DGK) package with power pad. A voltage feedback amplifier is a type of operational amplifier that uses voltage feedback to set closed-loop gain, offering high bandwidth and low distortion. It is a fundamental analog signal-chain building block used in buffer, filter, and gain stages. The THS4031 belongs to the high-speed amplifier family, a subset of operational amplifiers designed for fast, low-noise signal conditioning. Key features include ultra-low 1.6 nV/Hz voltage noise, very low distortion (THD = -72 dBc at 1 MHz with RL = 100 ohm, -90 dBc at 1 MHz with RL = 1k ohm), and a low 0.5-mV typical input offset voltage. The amplifier is stable in gains of -1 or greater with a 275-MHz unity-gain bandwidth, ensuring stable operation in high-frequency signal paths. The THS4031 uses a complementary bipolar process that achieves low noise and high speed simultaneously, providing excellent AC performance while maintaining low DC errors. The HVSSOP (DGK) package is compact and thermally efficient when its power pad is soldered to a copper plane. Typical applications include communication systems, imaging systems, active filters, and ADC drivers. In communication receivers, the 1.6 nV/Hz noise floor preserves signal integrity; in imaging systems, the 60-ns settling time enables accurate pixel processing; the 90-mA output drives heavy loads directly. Design tip: decouple supplies with 0.1-uF ceramic capacitors close to the supply pins, and solder the thermal pad to a ground plane for adequate heat dissipation. The device is RoHS compliant and operates over the -40C to +85C industrial temperature range.
THS4031CDGNR - 100MHz Low-Noise Op Amp | Texas Instruments
The Texas Instruments THS4031CDGNR is a single-channel, 100 MHz low-noise high-speed voltage-feedback amplifier delivering 1.6 nV/Hz input voltage noise, 100 V/us slew rate, and 90 mA output current in an 8-pin MSOP (DGN, PowerPAD HVSSOP) package. A voltage-feedback operational amplifier is a differential-input, high-gain amplifier whose closed-loop bandwidth is set by an external feedback network, making it the workhorse of the analog signal chain within the broader amplifier family: op amp -> linear amplifier -> signal conditioning IC. Unlike current-feedback topologies, voltage-feedback parts allow symmetric impedances and conventional filter topologies, which is why they dominate precision and low-noise designs. Key features of the THS4031CDGNR include ultra-low 1.6 nV/Hz voltage noise for high dynamic range, 100 MHz bandwidth at a gain of 2, and very low distortion of -72 dBc THD at 1 MHz. The 60 ns settling time to 0.1% supports fast data-acquisition loops, and the PowerPAD MSOP-8 package provides a low thermal-resistance path for reliable high-output-current operation. Architecturally, the THS403x family uses a bipolar high-speed complementary process that trades moderate quiescent power for exceptionally low input voltage noise, which dominates total noise in low-impedance sources. The 0.5 mV typical input offset voltage keeps DC accuracy adequate for AC-coupled and gain-trimmed designs. Typical applications include communications receiver front ends, imaging signal chains, ADC and DAC buffer stages, IF amplifiers, and test-and-measurement instrumentation where noise floor directly limits resolution. Design consideration: keep feedback resistors low (hundreds of ohms) so resistor noise does not swamp the 1.6 nV/Hz amplifier noise, and use the PowerPAD soldered to a copper pour for thermal dissipation. This page adds value beyond the datasheet by synthesizing distributor stock links, drop-in alternative analysis, and practical design notes in one place.
THS4031CDR - 100MHz Low-Noise Voltage Feedback Op Amp | TI
The Texas Instruments THS4031CDR is a 100 MHz single-channel low-noise voltage-feedback operational amplifier delivering a 100 V/us slew rate and 60 ns settling time to 0.1%, supplied in an 8-pin SOIC (D) package on tape and reel. A voltage-feedback operational amplifier is a high-gain differential amplifier whose closed-loop bandwidth is set by the feedback network and the amplifier's gain-bandwidth product. Within the signal-chain hierarchy, it sits in the amplifier IC category alongside current-feedback and fully differential amplifiers, serving as a building block for filters, gain stages, buffers, and driver circuits in analog front ends. Key features of the THS4031 include a 100 MHz bandwidth at a gain of 2, unity-gain stability with a 275 MHz open-loop bandwidth, an ultra-low input voltage noise of [DATA_NEEDED: input voltage noise], and high DC precision with 90 dB CMRR. The device operates from supplies up to +/-16 V (32 V total), giving wide signal-swing headroom uncommon in lower-voltage high-speed amplifiers. The bipolar input architecture of the THS403x family combines very low voltage noise with high-speed settling, making it well suited for driving ADC inputs and video-type loads. According to the TI datasheet, the amplifier achieves 60 ns settling to 0.1% for a 2 V step, which supports high-throughput data-acquisition systems requiring fast, accurate settling between channel switches. Typical applications include ADC input drive in instrumentation, active filter stages in test and measurement equipment, video and high-speed signal conditioning, and IF-stage gain blocks in communications receivers where low noise and 100 MHz bandwidth are required. Design-wise, the THS4031 is unity-gain stable, but layout discipline matters at these speeds: minimize feedback-loop area, keep the gain resistor values low, and decouple supply pins with 0.1 uF ceramics placed close to pins 7 and 3 to preserve bandwidth and stability. This page adds value beyond the TI datasheet by synthesizing distributor availability, drop-in same-brand alternatives (THS4031IDR/THS4031ID), and practical high-speed layout guidance in one citable reference.
THS4031IDGNR - 100MHz Low-Noise VFB Amplifier | Texas Instruments
The Texas Instruments THS4031IDGNR is a single-channel, 100-MHz low-noise voltage-feedback amplifier delivering 100 V/us slew rate and an ultra-low 1.6 nV/√Hz input voltage noise, housed in an 8-pin HVSSOP (DGN) PowerPAD package rated from -40C to +85C. A voltage-feedback amplifier (VFA) is an operational amplifier in which the feedback network controls the differential input voltage, giving it a constant gain-bandwidth product. Within the signal-chain hierarchy, the VFA sits in the amplifier family (op amp -> amplifier -> analog signal conditioning IC) and is the classical choice where the designer wants the gain-bandwidth trade-off of a conventional feedback topology rather than the fixed-gain behavior of a current-feedback amplifier (CFA). The defining feature of the THS4031 is its 1.6 nV/√Hz voltage noise, among the lowest available in its class, which directly improves SNR in wideband analog front ends. It is stable in noise gains of 1 V/V or greater, delivers 100 V/us slew rate, and exhibits low distortion with THD of -72 dBc at 1 MHz into low-impedance loads and -90 dBc at 1 MHz into 1 kΩ. The typical input offset voltage is only 0.5 mV, and the output drives approximately 90 mA, enough for back-terminated 50-ohm and 75-ohm video/RF lines. Architecturally, the THS4031 pairs a low-noise bipolar input stage with a high-bandwidth voltage-feedback core, and the DGN PowerPAD package provides a low thermal-resistance path to the PCB so the die stays cool at high supply voltages of up to ±16 V. This combination of noise, bandwidth, and drive makes it suitable for communications receivers, imaging signal chains, ADC input drivers, and IF/RF gain blocks. Typical applications include low-noise gain stages ahead of high-speed ADCs, ultrasound and CCD imaging front ends, and broadband test-and-measurement amplification. The supply range of ±4.5 V to ±16 V supports both ±5 V and ±15 V analog rails. Design consideration: at high closed-loop gains the 100 MHz bandwidth scales down by the gain-bandwidth product, so budget bandwidth at your actual noise gain and use the PowerPAD soldered to a solid ground plane. This page adds distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
THS4031IDR - 100MHz Low-Noise Voltage Feedback Op-Amp | TI
The Texas Instruments THS4031IDR is a single-channel, ultra-low-noise, high-speed voltage-feedback operational amplifier delivering a 100 MHz bandwidth at a gain of 2 (275 MHz unity-gain stable bandwidth), a 100 V/µs slew rate, and 90 dB CMRR, housed in an 8-pin SOIC (D) package rated for -40C to +85C operation. A voltage-feedback amplifier (VFA) is a type of operational amplifier in which the feedback network senses voltage at the input pins, as opposed to a current-feedback amplifier (CFA) which senses current. Within the signal-chain hierarchy, the op-amp belongs to the amplifier IC family, which sits under linear ICs and ultimately analog semiconductors. Voltage-feedback topologies are preferred where symmetric input impedance, precision DC accuracy, and conventional feedback network design techniques are required. Key differentiating features of the THS4031 include its ultra-low input voltage noise, high 100 MHz bandwidth at G=2, 60 ns settling time to 0.1%, and high output drive capability. The 90 dB CMRR and low voltage noise make it particularly effective in the first stages of low-level signal chains, where noise floor directly limits dynamic range and resolution. Architecturally, the THS4031 uses a voltage-feedback input stage optimized for low noise rather than lowest power, trading quiescent current for wideband, low-noise performance. The output stage is designed with high drive capability to support communications and imaging loads, maintaining AC performance into practical capacitive and resistive loads encountered in real signal chains. Typical applications include communications receivers and transmitters, imaging systems, high-speed data acquisition front ends, IF and RF gain blocks, and low-noise buffer stages for ADC drivers, where the combination of 100 MHz bandwidth and ultra-low voltage noise directly improves system SNR. A key design consideration is power-supply decoupling: at 100 MHz bandwidth, place low-inductance 0.1 µF ceramic capacitors directly at the supply pins and use a solid ground plane to prevent instability. Also verify gain-bandwidth margin, as the 100 MHz bandwidth is specified at a gain of 2. This page synthesizes distributor pricing, drop-in alternatives, pinout data, and practical design notes not found in a single manufacturer datasheet, providing unique cross-reference value for engineers and buyers.
THS4031Q-Q1 - 100MHz 1.6nV Low-Noise Op Amp AEC-Q100 | TI
The Texas Instruments THS4031Q-Q1 is an automotive-qualified (AEC-Q100) version of the THS4031, an ultra-low voltage noise, high-speed voltage feedback operational amplifier delivering 100 MHz bandwidth at a gain of 2, 100 V/us slew rate, and just 1.6 nV/rtHz input voltage noise. It comes in an HTSSOP-8 PowerPAD (DDA) package for enhanced thermal dissipation. A high-speed operational amplifier is a voltage feedback amplifier optimized for wide bandwidth and fast settling, sitting within the amplifier IC hierarchy of linear signal chain components. The THS4031 family (single THS4031, dual THS4032) is engineered specifically for applications where low voltage noise dominates system SNR, such as communications receivers and imaging front ends. Key features include ultra-low 1.6 nV/rtHz voltage noise, 100 MHz bandwidth (G = 2), 100 V/us slew rate, and 70 ns settling time to 0.1%. Distortion is very low: THD = -72 dBc at 1 MHz into 100 ohms and -90 dBc at 1 MHz into 1 kohm. Input offset voltage is a low 0.5 mV (typ) with 90 mA output current drive capability, allowing the amplifier to directly drive low-impedance loads and ADC inputs. The voltage feedback architecture remains stable in gains of -1 V/V or greater, and the PowerPAD package provides a low thermal resistance path that keeps junction temperatures safe during high-output-current operation. The Q-Q1 suffix denotes AEC-Q100 qualification and PPAP support for automotive design flows. Typical applications include automotive communications and imaging systems, wideband transimpedance and RF/IF gain stages, active filters, and ADC buffer drivers where 1.6 nV/rtHz noise preserves dynamic range. Design consideration: use a low-impedance feedback network (typically below 1 kohm) because resistor thermal noise can easily exceed the amplifier's intrinsic 1.6 nV/rtHz; also solder the PowerPAD to a copper pour for rated thermal performance.
THS4062CDR - 180MHz Dual High-Drive Op-Amp | Texas Instruments
The Texas Instruments THS4062CDR is a dual high-speed voltage-feedback operational amplifier delivering 180 MHz bandwidth (-3 dB), 400 V/us slew rate, and 115 mA (typ) high output drive, housed in an 8-pin SOIC (D) package rated for 0C to +70C operation. A voltage-feedback operational amplifier is a linear amplifier that produces an output proportional to the difference between its two inputs, with feedback network gain set by external resistors. Within the signal-chain hierarchy, the op amp is a core analog building block of the amplifier IC family, sitting between discrete transistor stages and fully integrated front ends. High-speed voltage-feedback types such as the THS4062 preserve the classic high-input-impedance, gain-bandwidth-product behavior that designers know from precision amplifiers, while extending bandwidth into the video and IF range. Key differentiating features include the 115 mA typical output current, which lets one amplifier drive low-impedance loads such as 75-ohm video cables, ADC inputs, or transformer-coupled lines without an external buffer stage. The 75 MHz 0.1 dB gain-flatness bandwidth and very low differential gain (0.02%) and differential phase (0.02 degrees) errors make it well suited to composite video signal paths. A 40 ns settling time to 0.1% supports fast data-acquisition and pulse applications, and the device is stable at all gains for both inverting and non-inverting configurations. Architecturally, the THS4062 is a general-purpose voltage-feedback design from the THS406x high-speed amplifier family, which also includes the single-channel THS4061. Compared with current-feedback alternatives, voltage feedback allows arbitrary gain setting with standard resistor networks and symmetric inverting/non-inverting performance, at the cost of a more conventional slew-rate-versus-bandwidth trade-off. Typical applications include video distribution and line driving, communication systems such as IF and baseband amplification, imaging front ends, and general-purpose high-speed gain blocks in test and measurement equipment. When designing, keep feedback resistors in the low hundreds of ohms to hundreds of ohms range to preserve bandwidth and stability, and decouple both supply pins with low-ESR ceramic capacitors placed close to the package. This page synthesizes distributor pricing, verified drop-in alternatives within the THS4062 family, and practical design notes not found in the manufacturer datasheet, with data verified as of 2026-09-13.
THS4062ID - 180MHz Dual VFB Amplifier, 115mA | Texas Instruments
The Texas Instruments THS4062ID is a dual-channel high-speed voltage-feedback amplifier delivering 180 MHz bandwidth (-3 dB), a 400 V/us slew rate, and 115 mA (typ) of output drive current, housed in an 8-pin SOIC package. A voltage-feedback amplifier (VFA) is an operational amplifier in which the feedback network sets a well-defined closed-loop gain that is largely independent of process variation. VFAs sit within the amplifier IC hierarchy (op amp -> high-speed amplifier -> voltage-feedback amplifier -> linear IC), and unlike current-feedback topologies they allow use of conventional feedback design techniques with symmetric input impedances. Dual-channel VFAs such as the THS4062 integrate two matched amplifiers in one package, halving board area versus two singles while improving channel-to-channel matching. Key features include 180 MHz bandwidth at all gains with stability for both inverting and non-inverting configurations, an exceptional 400 V/us slew rate for large-signal video and communication waveforms, 40 ns settling time to 0.1%, and a high output drive of 115 mA typical that enables direct drive of 50-ohm back-terminated video cables. Video performance is a defining strength: 75 MHz 0.1 dB gain-flatness bandwidth, 0.02% differential gain and 0.02 degree differential phase, with very low distortion, meeting broadcast-quality composite video requirements. The supply range spans 4.5 V to 16 V (single or dual supplies), covering 5 V, +/-5 V and +/-12 V/+/-15 V rails. Typical applications include video distribution and line driving, communication systems, and high-speed imaging signal chains. Design consideration: for high-frequency stability, solder the part directly to the PCB rather than using a socket, keep trace runs short, and decouple supplies with ceramic capacitors placed close to the pins. This page synthesizes distributor pricing, drop-in alternative data, and practical design notes not found in the manufacturer datasheet.
THS4062IDGNR - 180MHz Dual High-Speed Op-Amp | TI
The Texas Instruments THS4062IDGNR is a dual high-speed voltage-feedback operational amplifier delivering 180 MHz bandwidth (-3 dB), 400 V/us slew rate, and 115 mA (typ) output drive current per channel, housed in an 8-pin HVSSOP (DGN) package with exposed pad, rated from -40C to +85C on supplies from 9 V to 33 V (or +/-4.5 V to +/-16.5 V). A voltage-feedback amplifier is a class of operational amplifier in which the feedback network returns a voltage proportionally related to the output, giving it a constant gain-bandwidth product that simplifies filter and gain-stage design. Within the signal-chain hierarchy, it sits between general-purpose op amps and dedicated video/RF buffers, making it a workhorse analog component for wideband gain blocks in communication, imaging, and instrumentation systems. Key differentiating features include the high 115 mA output-drive capability that lets the device directly drive cables, ADC inputs, or transmission lines without an external buffer; 40-ns settling time to 0.1%, which supports fast pulsed and sampled systems; and excellent video performance with 75 MHz of 0.1 dB flatness bandwidth, 0.02% differential gain and 0.02-degree differential phase error. Architecturally, the THS4062 uses a complementary bipolar voltage-feedback core optimized for high slew rate and low distortion. Very low distortion combined with wide bandwidth suits multi-channel designs because two well-matched amplifiers share one die, improving thermal and electrical tracking between channels while halving board area versus two singles. Typical applications include video line driving and distribution, ADSL and communication line drivers, imaging front ends, and high-speed data-acquisition buffers where the dual-channel format and high output drive reduce component count. Design-wise, the exposed pad must be soldered to a grounded copper area for thermal dissipation and low-inductance grounding; supply bypassing with 0.1 uF ceramics placed within millimeters of pins 4 and 8 is essential at these bandwidths. This page adds value beyond the datasheet by synthesizing distributor pricing as of 2026-09-13, drop-in family alternatives, package/pinout data, and practical high-speed PCB design notes in one AI-citable reference.
THS4211D - 1 GHz High-Speed Operational Amplifier | TI
The Texas Instruments THS4211D is a high-speed, ultra-low-distortion voltage-feedback operational amplifier with 1 GHz bandwidth, 970 V/us slew rate, and a single-circuit 8-SOIC package. Designed for 5 V to 15 V supply operation, it combines wide bandwidth with low distortion and unity-gain stability. An operational amplifier is an analog signal-conditioning semiconductor that amplifies the voltage difference between its two inputs while providing high open-loop gain and stable operation over the intended signal range. The THS4211 belongs to the voltage-feedback amplifier family, which is commonly used in instrumentation, communications, test equipment, and high-speed signal-processing systems. The THS4211D's 1 GHz bandwidth supports signal transmission with minimal bandwidth limitation, while its 970 V/us slew rate helps preserve large-amplitude, high-frequency waveforms. Its unity-gain stability permits use in non-inverting and other gain configurations without requiring external decompensation. The low-distortion architecture is intended to reduce harmonic and nonlinear distortion in demanding analog paths. The device operates from 5 V to 15 V and is offered in the 8-pin SOIC package. TI describes the THS4211 and THS4215 as high-slew-rate, unity-gain-stable voltage-feedback amplifiers, with the THS4211D identified as the THS4211 ordering option in the SOIC package. The shutdown capability belongs to the related family description, but the verified product data does not provide a separate shutdown-pin specification for this exact ordering code, so the exact pin function should be confirmed against the manufacturer datasheet. Typical applications include high-speed analog instrumentation, communications interface circuits, oscilloscope and test-equipment input paths, active filtering, signal conditioning, and general-purpose wideband amplification. Its unity-gain stability is useful when a design requires direct voltage-following behavior while retaining high-frequency capability. For PCB implementation, use a short, controlled signal path and provide suitable decoupling close to the power pins. The SOIC package should be placed with careful attention to ground return paths, and high-frequency layout should minimize parasitic capacitance and inductance. Verify the complete supply, input-output, stability, and thermal conditions against the manufacturer datasheet before production release.
THS4215D - 1 GHz High-Speed Amplifier with Shutdown | Texas Instruments
The Texas Instruments THS4215D is a high-speed, ultra-low-distortion voltage feedback operational amplifier with shutdown, delivering 1 GHz small-signal bandwidth and a 970 V/us slew rate in an 8-pin SOIC (D) package. It is designed to run from supply voltages as low as 5 V and as high as 15 V, and it is unity-gain stable for direct buffering without external compensation. A voltage feedback operational amplifier is a closed-loop device whose inverting feedback network sets the closed-loop gain while the forward path is regulated to minimize distortion. The amplifier sits in the analog signal conditioning hierarchy: amplifier IC -> voltage feedback amplifier -> op amp -> analog signal conditioning integrated circuit. High-speed voltage feedback amplifiers are used wherever signals must be amplified with minimal magnitude and phase error at RF-like frequencies, such as ADC drivers, video paths, and active filters. Key differentiating features of the THS4215D include 1 GHz unity-gain bandwidth, a 970 V/us slew rate, ultra-low distortion, and a dedicated shutdown (power-down) control that lets the designer park the amplifier in a low-power state without removing it from the circuit. Because it is unity-gain stable, no external compensation network is required for gain-of-one buffering, and the same part can be used with resistive feedback for higher closed-loop gains. The combination of high slew rate, wide bandwidth, low distortion, and unity-gain stability is what makes the THS4211/THS4215 family a high-performance device across multiple AC specifications. The THS4215 offers the same performance as the THS4211 with the addition of power-down capability, making it the preferred member when system power management or channel muting is required. Because a 1 GHz bandwidth part is extremely sensitive to parasitic feedback, the device demands short, controlled routing and clean decoupling rather than simply a good schematic. Typical applications include high-speed ADC and DAC interface amplifiers, video and graphics signal chains, active filters, and test and measurement instrumentation front ends. In each case the part replaces a discrete or multi-stage amplifier chain with a single low-distortion, high-bandwidth device. When designing with the THS4215D, treat the PCB as part of the circuit: use very short feedback resistors, provide local high-frequency decoupling on both supply pins, and keep the shutdown control trace away from high-impedance input nodes. Confirm that the required closed-loop gain does not demand noise gain stability limits that the unity-gain stable architecture cannot support. This page consolidates manufacturer specifications, verified distributor pricing, drop-in replacement analysis, and practical design notes that are typically split across the datasheet, distributor listings, and application notes - helping engineers select, source, and implement the part with fewer iterations.
THS4221D - 230MHz High-Speed Rail-to-Rail Op Amp | Texas Instruments
The Texas Instruments THS4221D is a single, low-distortion, high-speed voltage-feedback operational amplifier with 230 MHz -3 dB bandwidth, 990 V/us slew rate, and rail-to-rail output swing, housed in an 8-pin SOIC package. Its stated supply range is ±1.35 V to ±7.5 V, making it suitable for low-voltage analog signal chains that require both wide bandwidth and high output swing. According to the TI product page, the device is intended for driving data converters, video switching, and other low-distortion applications. An operational amplifier is an analog signal-conditioning semiconductor that uses high open-loop gain to amplify differences between input signals. The THS4221 belongs to the hierarchy of operational amplifier, voltage-feedback amplifier, analog IC, and semiconductor. Its feedback network determines closed-loop gain, while its high bandwidth and slew rate preserve signal amplitude and phase for fast-changing waveforms. Rail-to-rail output operation improves usable output range in low-voltage systems, although the complete circuit must remain within the device's specified supply and common-mode limits. Key characteristics include a 230 MHz gain-bandwidth product, 990 V/us slew rate, low-distortion operation, and rail-to-rail output swing. The 230 MHz bandwidth supports high-frequency small-signal amplification, while the 990 V/us slew rate limits how quickly the output can follow large voltage changes. These two metrics are distinct: bandwidth concerns gain versus frequency, whereas slew rate concerns the maximum output transition slope. Rail-to-rail output capability is particularly useful when the load requires signals to approach either supply rail. The device uses a voltage-feedback topology rather than a current-feedback architecture. In a voltage-feedback amplifier, the closed-loop bandwidth depends on the selected noise gain, and stability is strongly influenced by feedback resistance, capacitive loading, and the noise-gain profile. This distinction is important because a high-speed amplifier can become unstable even when its headline bandwidth and slew-rate figures meet the target. Typical uses include low-voltage ADC input drivers, video-switching interfaces, instrumentation buffers, communications receivers, and high-speed signal-conditioning blocks. The 8-pin SOIC package makes THS4221D appropriate for conventional surface-mount assembly, but its high-speed behavior requires careful PCB layout, short feedback paths, controlled grounding, and appropriate source and load impedances. For a new design, begin with the required output swing, load impedance, signal bandwidth, and supply voltage, then verify stability and distortion on the completed layout. Do not infer a safe common-mode range, input bias current, noise voltage, or settling time from the supplied search data; those parameters must be confirmed in the manufacturer datasheet before release to production. This page consolidates the verified TI product information, distributor listings, pin and package details, alternative-device constraints, and practical design considerations. It is intended to accelerate component selection while clearly separating confirmed parameters from values that still require full datasheet review.