Produk (46,000+)

STM32F103ZET6TR - 72MHz Cortex-M3 MCU 512KB Flash | STMicroelectronics (Tape & Reel)
STM32F103ZET6TR

STM32F103ZET6TR - 72MHz Cortex-M3 MCU 512KB Flash | STMicroelectronics (Tape & Reel)

The STMicroelectronics STM32F103ZET6TR is a high-density performance line 32-bit microcontroller built on the ARM Cortex-M3 core running at up to 72 MHz, with 512 KB of Flash memory, 64 KB of SRAM, and 112 GPIOs in a 144-pin LQFP (20 x 20 mm) package operating from a 2.0 V to 3.6 V supply. A microcontroller (MCU) is a compact integrated circuit that combines a processor core, memory, and programmable peripherals on a single chip to govern a specific operation in an embedded system. MCUs sit at the heart of the embedded electronics hierarchy - from the ARM Cortex-M processor core, through the STM32 family of 32-bit microcontrollers, up to complete embedded control systems used in industrial automation, consumer devices, and IoT products. Key features include three 12-bit ADCs with up to 21 channels, two 12-bit DACs, a 12-channel DMA controller, and an unusually rich communication set: up to 5 USARTs, 3 SPIs, 2 I2Cs, 1 CAN 2.0B, 1 USB 2.0 Full-Speed, and 1 SDIO interface. The Cortex-M3 core delivers 1.25 DMIPS/MHz (Dhrystone 2.1), giving roughly 90 DMIPS at 72 MHz, while the Nested Vectored Interrupt Controller (NVIC) provides low-latency deterministic interrupt handling. Architecturally, the device integrates advanced-control, general-purpose, and basic timers (including PWM timers for motor control), a real-time clock (RTC), and a CRC calculation unit. Both JTAG and Serial Wire Debug (SWD) interfaces are supported, and boot can be selected from Flash, system memory, or SRAM. The 512 KB Flash and 112 GPIOs of the LQFP144 make it the largest-pin, largest-memory STM32F103 variant, ideal for complex firmware with real-time control and multiple communication stacks. Typical applications include industrial control and PLC systems, motor drives, medical devices, communication boards, and IoT gateways. The wide 2.0 V to 3.6 V supply range and -40C to +85C operating temperature support both battery-powered and industrial designs. When designing with this device, decouple every VDD pin with 100 nF ceramic capacitors placed close to the pins plus one bulk capacitor, and filter VDDA with a ferrite bead to protect the 12-bit ADC noise floor. The BOOT0/BOOT1 pins must be strapped correctly at reset to select the desired boot source. This page adds value beyond the ST datasheet by synthesizing drop-in alternatives (GD32F103ZET6, APM32E103ZET6), pricing tiers, engineering design notes, and application guidance in one citable reference.

USD $5.39 Hubungi kami
STM32F103ZET7 - 72MHz Cortex-M3 512KB MCU | STMicroelectronics
STM32F103ZET7

STM32F103ZET7 - 72MHz Cortex-M3 512KB MCU | STMicroelectronics

The STMicroelectronics STM32F103ZET7 is a 32-bit ARM Cortex-M3 microcontroller operating at up to 72 MHz, with 512 KB of embedded Flash memory and USB, CAN, 11 timers, 3 ADCs, and 13 communication interfaces. It is packaged in a 144-LQFP 20 mm x 20 mm package. The STM32F103ZET7 belongs to STMicroelectronics’ high-density performance-line STM32F1 MCU family. A microcontroller is a programmable system-on-chip that integrates a processor core, memory, peripherals, and communication interfaces on one semiconductor device. The STM32F1 family combines an ARM Cortex-M3 RISC core with embedded control peripherals, making it suitable for industrial equipment, data acquisition, communications, motor control, and embedded automation. Its 32-bit architecture supports efficient control tasks and higher processing performance than many 8-bit or 16-bit alternatives. The STM32F103ZET7 provides 512 KB of Flash for firmware and 2.5 V/3.3 V operation as identified in the verified distributor and datasheet listings. Its feature set includes USB, CAN, 11 timers, 3 ADCs, and 13 communication interfaces. These resources allow one controller to coordinate analog measurement, timing, communication protocols, and control outputs while reducing the number of discrete components in a design. The device is identified as a 144-LQFP 20 mm x 20 mm surface-mount package. Its high pin count supports broad peripheral access and makes the STM32F103ZET7 useful for designs requiring numerous I/O functions, communications, and motor-control signals. The verified listing identifies the part as a 32-bit Cortex-M3 MCU with 72 MHz operation and 512 KB Flash memory. Typical applications include industrial control systems, IoT devices, embedded automation, motor control, metering equipment, USB-connected instrumentation, CAN-based nodes, and low-power embedded boards. Firmware selection should verify clock configuration, peripheral pin assignments, memory mapping, and the STM32F1 reference manual requirements before production release. This page combines verified manufacturer and distributor information with structured engineering guidance. Pricing, availability, lifecycle status, detailed electrical limits, and complete pin naming are not fully supplied in the retrieved data and must be confirmed against current manufacturer or distributor documentation before purchase or design approval.

RFC Hubungi kami
STM32F103ZFH6 - 72MHz Cortex-M3 768KB MCU | STMicroelectronics
STM32F103ZFH6

STM32F103ZFH6 - 72MHz Cortex-M3 768KB MCU | STMicroelectronics

The STMicroelectronics STM32F103ZFH6 is a 32-bit ARM Cortex-M3 microcontroller with a maximum operating frequency of 72 MHz, 768 KB of Flash memory, and a 144-LFBGA 10 x 10 mm package. It also supports operation from a 2.5 V or 3.3 V supply, combining embedded Flash, SRAM, communication peripherals, timers, and analog conversion functions in one surface-mount device. A microcontroller is an integrated circuit that executes embedded software while coordinating digital inputs, outputs, communications, and analog measurements. Within the product hierarchy, the STM32F103ZFH6 is an ARM Cortex-M3 MCU, a 32-bit microcontroller, and a member of STMicroelectronics' STM32 embedded-processing family. It is intended for systems that require substantially more Flash memory and I/O than small 8-bit or 16-bit control devices. The verified product information identifies the STM32F103ZFH6 as a 72 MHz device with 768 KB of Flash organized as 768K x 8. Its 32-bit Cortex-M3 core provides the processing foundation for control loops, communications gateways, human-interface systems, and data acquisition. The 144-LFBGA package supplies 144 connection points in a compact 10 x 10 mm surface-mount footprint suitable for multilayer PCB designs. The STM32F103 family is associated with USB, CAN, six timers, two ADCs, and six communication interfaces. These functions support designs connecting external digital devices, transferring data over serial or network links, measuring analog signals, and controlling time-dependent peripherals. The available verified data does not specify individual GPIO counts, SRAM capacity, ADC resolution, or communication baud-rate limits, so those values must be confirmed in the manufacturer datasheet before final system design. Typical applications include industrial automation equipment, USB-connected embedded controllers, CAN network nodes, data-acquisition systems, motor and motion-control platforms, and communication equipment. The 72 MHz Cortex-M3 core can manage multiple interrupt-driven peripherals while the 768 KB Flash capacity accommodates larger embedded applications, protocol stacks, and application firmware. The principal design consideration is package and PCB complexity. A 144-LFBGA device requires a multilayer board, fine-pitch routing, controlled escape routing, and careful thermal management. Designers should also verify peripheral assignments, pin multiplexing, power sequencing, decoupling, and firmware support against the exact datasheet and reference manual before releasing hardware. This page consolidates verified distributor pricing, package details, technical attributes, sourcing links, and design guidance into one engineering-focused reference. It also distinguishes explicitly verified information from parameters that require confirmation from the manufacturer datasheet.

RFC Hubungi kami
STM32F103ZFH6TR - 72MHz Cortex-M3 MCU | STMicroelectronics
STM32F103ZFH6TR

STM32F103ZFH6TR - 72MHz Cortex-M3 MCU | STMicroelectronics

The STMicroelectronics STM32F103ZFH6TR is a 32-bit ARM Cortex-M3 microcontroller operating at 72 MHz, with 768 KB of embedded Flash memory in a 144-LFBGA (10 x 10 mm) package. It combines a high-performance RISC core with integrated microcontroller peripherals in a compact surface-mount package suitable for space-constrained embedded products. A microcontroller is a programmable semiconductor device that executes firmware, reads sensors, controls actuators, and manages system communication. The STM32F103 product family belongs to the embedded-processing hierarchy: ARM Cortex-M3 core, 32-bit microcontroller, embedded controller, and semiconductor. The STM32F103ZFH6TR is intended for applications requiring more memory and package I/O than smaller STM32F103 variants while retaining the established Cortex-M3 architecture. The device features a 72 MHz maximum clock, 768 KB of Flash memory, and an operating supply range of 2.0 V to 3.6 V. The manufacturer listing identifies 37 I/O ports, an ARM 32-bit RISC architecture, and a 144-LFBGA package measuring 10 x 10 mm. Its performance-line positioning supports embedded control applications that require deterministic real-time execution, serial communication, mixed-signal measurement, and external peripheral control. Its 144-pin LFBGA construction provides a dense connection interface within a small footprint. The 0.5 mm ball pitch supports compact board layouts but requires careful PCB design, inspection, and assembly controls. The TR ordering suffix identifies a tape-and-reel shipping format, which supports automated manufacturing and volume production. Use the manufacturer pin-description table and land-pattern guidance when assigning every ball and defining the PCB footprint. Typical uses include industrial controllers, USB-connected data-acquisition equipment, CAN network nodes, motor-control systems, instrumentation, and communication gateways. The 768 KB Flash capacity is useful for firmware, configuration data, and application code, while the 72 MHz Cortex-M3 core provides the processing headroom required for concurrent peripheral control and protocol handling. The primary design consideration is package implementation. A 144-LFBGA assembly requires an HDI-capable board process, fine-pitch assembly capability, and careful power, ground, and signal-integrity layout. Confirm the exact ball assignments, exposed-pad requirements, and recommended PCB stackup in the manufacturer datasheet before releasing artwork. This product page consolidates the exact device identity, technical characteristics, compatible same-family options, practical application guidance, and PCB considerations into one engineering reference. It also supports structured sourcing through the Request a Quote form on this page for availability, lead-time, and order requirements.

RFC Hubungi kami
STM32F103ZFT6 - 32-Bit 72MHz 768KB MCU | STMicroelectronics
STM32F103ZFT6

STM32F103ZFT6 - 32-Bit 72MHz 768KB MCU | STMicroelectronics

The STMicroelectronics STM32F103ZFT6 is a 32-bit ARM Cortex-M3 microcontroller with a 72 MHz maximum clock, 768 KB of Flash memory, and a 144-LQFP package measuring 20 mm by 20 mm. It belongs to the STM32F1 performance-line family and combines embedded control, communications, analog conversion, timer, and motor-control resources in one surface-mount device. An ARM Cortex-M3 microcontroller is a reduced-instruction-set embedded processor designed for real-time control systems. The Cortex-M3 core supplies deterministic instruction execution and interrupt handling, while the STM32F103 family integrates peripherals such as timers, communication interfaces, ADCs, USB, and CAN around that core. This hierarchy places the MCU above the processor core and into the broader embedded-control and semiconductor categories. The verified source data identifies the STM32F103ZFT6 as an XL-density member with 768 KB of Flash and a maximum frequency of 72 MHz. The same source states 1.25 DMIPS/MHz, supporting use in demanding embedded-control designs without requiring an external processor. Its large pin count also accommodates extensive I/O and peripheral connectivity compared with smaller STM32 packages. The manufacturer family description associates STM32F103 devices with USB, CAN, six timers, two ADCs, and six communication interfaces. These resources make the MCU suitable for gateways, motor controllers, industrial communication equipment, CAN or LIN-connected nodes, and embedded systems that require both control and communications. The verified data also lists vehicle gateway nodes and CAN/LIN networks as relevant use cases. A key engineering consideration is that the LQFP-144 footprint exposes substantially more interface pins than a compact MCU, enabling parallel I/O and multiple peripheral assignments while demanding careful PCB escape routing. Firmware and peripheral assignments should be validated against the manufacturer pinout and reference documentation before layout release. Alternate clock, memory, and analog behavior must also be checked when evaluating any substitute. This page combines verified distributor and manufacturer-linked source information, practical sourcing context, and structured MCU application guidance. It distinguishes the device’s confirmed 72 MHz and 768 KB attributes from parameters that remain unavailable, avoiding unsupported claims about electrical limits, temperature range, or compliance.

RFC Hubungi kami
STM32F103ZGH6 - 72MHz 1MB Cortex-M3 MCU | STMicroelectronics
STM32F103ZGH6

STM32F103ZGH6 - 72MHz 1MB Cortex-M3 MCU | STMicroelectronics

The STMicroelectronics STM32F103ZGH6 is a 32-bit ARM Cortex-M3 microcontroller operating at up to 72 MHz, with 1 MB of Flash memory in a 144-pin LQFP package. Designed as an XL-density member of the STM32F1 series, it combines a high-performance 32-bit RISC core with extensive embedded connectivity and control peripherals. Its 2.5 V and 3.3 V operating references make it suitable for conventional embedded systems, while the large pin count exposes substantial I/O and peripheral connectivity. A microcontroller is a programmable semiconductor system that integrates a CPU core, memory, communication interfaces, timers, analog inputs, and I/O on one package. In the STM32 hierarchy, the STM32F103ZGH6 belongs to the STM32F1 mainstream family, the Cortex-M3 performance class, and the broader category of embedded-system microcontrollers. This position explains its combination of a 72 MHz clock, substantial Flash storage, and a large surface-mount package. The verified product data identifies an ARM Cortex-M3 core, 1 MB Flash, a 72 MHz maximum operating frequency, and 2.5 V or 3.3 V supply references. It also identifies the STM32F103 series as supporting USB, CAN, timer, ADC, and communication functions, although exact peripheral counts, SRAM capacity, pin functions, electrical limits, and timing values require confirmation in the manufacturer datasheet. These unverified quantities are therefore not inferred on this page. The 144-pin LQFP package provides a large number of external connections relative to smaller 32-, 48-, and 64-pin MCUs. That makes the STM32F103ZGH6 suitable when a design needs substantial GPIO availability alongside USB, CAN, analog, timer, and serial-interface resources. The tradeoff is a larger board footprint, more fine-pitch routing, and more complex assembly than a smaller LQFP package. Typical applications include industrial control equipment, USB-connected data acquisition, CAN-based supervisory systems, medical monitoring equipment, consumer electronics, and communication modules. In these systems, the MCU can execute control logic, supervise sensors, drive digital outputs, and exchange data through its integrated interfaces. Firmware should be validated at the intended clock and supply settings before deployment. Designers must confirm the complete pin assignment, absolute maximum ratings, decoupling requirements, clock limits, and peripheral electrical conditions from the manufacturer datasheet. Because the available search data does not expose a complete verified pin map, the page does not fabricate individual pin names. A large-package PCB should also provide short ground-return paths, controlled clock routing, and adequate decoupling close to the device. This page consolidates verified distributor specifications, practical application guidance, pricing-data gaps, and qualification-aware drop-in comparisons. It is intended to help engineers identify whether the STM32F103ZGH6 fits their PCB and firmware requirements while clearly separating confirmed facts from information that still requires datasheet validation.

RFC Hubungi kami
STM32F103ZGH6J - 72MHz Cortex-M3 MCU | STMicroelectronics
STM32F103ZGH6J

STM32F103ZGH6J - 72MHz Cortex-M3 MCU | STMicroelectronics

STMicroelectronics STM32F103ZGH6J is a 32-bit ARM Cortex-M3 microcontroller operating at up to 72 MHz, with 1 MB of Flash memory organized as 1M x 8 and supplied in a 144-LFBGA 10 x 10 mm package. It is a member of the STM32F103 mainstream-performance line and targets embedded systems requiring substantial program storage in a compact surface-mount package. A microcontroller, or MCU, integrates a processor core, programmable memory, data memory, and peripheral interfaces into one semiconductor package. The STM32F1 series sits within the hierarchy of microcontrollers, embedded processors, and programmable control devices. MCUs are used where a system must execute firmware, acquire inputs, control outputs, and manage communications without requiring a separate external processor and supporting logic. The verified specifications identify an Arm Cortex-M3 core, 32-bit processing capability, a maximum clock frequency of 72 MHz, and 1 MB of Flash memory. The 1M x 8 organization indicates that the program memory is configured for byte-addressable storage. These headline figures make the STM32F103ZGH6J suitable for control-intensive embedded products with moderate firmware complexity and comparatively high processing throughput for a mainstream 32-bit MCU. The STM32F103 device family combines a compact embedded architecture with a broad set of conventional microcontroller functions. Its 72 MHz Cortex-M3 operating point provides substantial headroom for protocol handling, digital control, state-machine execution, and concurrent peripheral servicing. The 1 MB Flash capacity also gives developers room for application firmware, configuration data, boot logic, and field-update routines without immediately requiring external program-memory devices. Typical applications include industrial control equipment, data acquisition systems, communication gateways, motor and motion-control assemblies, instrumentation, and connected embedded products. In each case, the MCU can execute application software and coordinate inputs and outputs while preserving a compact board footprint. The 144-LFBGA package is especially useful when high pin or interconnect density is valuable, although it requires careful PCB layout and inspection because its ball grid leaves little space between contacts. Designers should verify the exact pin allocation, power rails, decoupling requirements, clock configuration, and exposed or connected balls against the manufacturer datasheet before layout. Because the verified search results identify a 144-LFBGA package but do not provide a complete public pin table, this page does not reproduce an unverified 144-pin map. Production sourcing should also confirm stock, minimum order quantity, and price directly with an authorized distributor. This page combines the verified STM32F103ZGH6J specifications, current distributor references, package details, and practical engineering guidance. It also distinguishes documented drop-in alternatives from general MCU substitutions, helping engineers evaluate PCB compatibility without mistaking a broadly similar Cortex-M3 product for a true same-footprint replacement.

RFC Hubungi kami
STM32F103ZGH6JTR - 72MHz Cortex-M3 MCU | STMicroelectronics (Tape & Reel)
STM32F103ZGH6JTR

STM32F103ZGH6JTR - 72MHz Cortex-M3 MCU | STMicroelectronics (Tape & Reel)

STMicroelectronics STM32F103ZGH6JTR is a 32-bit ARM Cortex-M3 microcontroller operating at up to 72 MHz, with 1 MB of Flash memory organized as 1M x 8 and supplied in a 144-LFBGA 10 x 10 mm package. It is a member of the STM32F103 mainstream-performance line and targets embedded systems requiring substantial program storage in a compact surface-mount package. A microcontroller, or MCU, integrates a processor core, programmable memory, data memory, and peripheral interfaces into one semiconductor package. The STM32F1 series sits within the hierarchy of microcontrollers, embedded processors, and programmable control devices. MCUs are used where a system must execute firmware, acquire inputs, control outputs, and manage communications without requiring a separate external processor and supporting logic. The verified specifications identify an Arm Cortex-M3 core, 32-bit processing capability, a maximum clock frequency of 72 MHz, and 1 MB of Flash memory. The 1M x 8 organization indicates that the program memory is configured for byte-addressable storage. These headline figures make the STM32F103ZGH6JTR suitable for control-intensive embedded products with moderate firmware complexity and comparatively high processing throughput for a mainstream 32-bit MCU. The STM32F103 device family combines a compact embedded architecture with a broad set of conventional microcontroller functions. Its 72 MHz Cortex-M3 operating point provides substantial headroom for protocol handling, digital control, state-machine execution, and concurrent peripheral servicing. The 1 MB Flash capacity also gives developers room for application firmware, configuration data, boot logic, and field-update routines without immediately requiring external program-memory devices. Typical applications include industrial control equipment, data acquisition systems, communication gateways, motor and motion-control assemblies, instrumentation, and connected embedded products. In each case, the MCU can execute application software and coordinate inputs and outputs while preserving a compact board footprint. The 144-LFBGA package is especially useful when high pin or interconnect density is valuable, although it requires careful PCB layout and inspection because its ball grid leaves little space between contacts. Designers should verify the exact pin allocation, power rails, decoupling requirements, clock configuration, and exposed or connected balls against the manufacturer datasheet before layout. Because the verified search results identify a 144-LFBGA package but do not provide a complete public pin table, this page does not reproduce an unverified 144-pin map. Production sourcing should also confirm stock, minimum order quantity, and price directly with an authorized distributor. This page combines the verified STM32F103ZGH6JTR specifications, current distributor references, package details, and practical engineering guidance. It also distinguishes documented drop-in alternatives from general MCU substitutions, helping engineers evaluate PCB compatibility without mistaking a broadly similar Cortex-M3 product for a true same-footprint replacement.

RFC Hubungi kami
STM32F103ZGH6TR - 72MHz 1MB Cortex-M3 MCU | STMicroelectronics (Tape & Reel)
STM32F103ZGH6TR

STM32F103ZGH6TR - 72MHz 1MB Cortex-M3 MCU | STMicroelectronics (Tape & Reel)

The STMicroelectronics STM32F103ZGH6TR is a 32-bit ARM Cortex-M3 microcontroller operating at up to 72 MHz, with 1 MB of Flash memory in a 144-pin LQFP package. Designed as an XL-density member of the STM32F1 series, it combines a high-performance 32-bit RISC core with extensive embedded connectivity and control peripherals. Its 2.5 V and 3.3 V operating references make it suitable for conventional embedded systems, while the large pin count exposes substantial I/O and peripheral connectivity. A microcontroller is a programmable semiconductor system that integrates a CPU core, memory, communication interfaces, timers, analog inputs, and I/O on one package. In the STM32 hierarchy, the STM32F103ZGH6TR belongs to the STM32F1 mainstream family, the Cortex-M3 performance class, and the broader category of embedded-system microcontrollers. This position explains its combination of a 72 MHz clock, substantial Flash storage, and a large surface-mount package. The verified product data identifies an ARM Cortex-M3 core, 1 MB Flash, a 72 MHz maximum operating frequency, and 2.5 V or 3.3 V supply references. It also identifies the STM32F103 series as supporting USB, CAN, timer, ADC, and communication functions, although exact peripheral counts, SRAM capacity, pin functions, electrical limits, and timing values require confirmation in the manufacturer datasheet. These unverified quantities are therefore not inferred on this page. The 144-pin LQFP package provides a large number of external connections relative to smaller 32-, 48-, and 64-pin MCUs. That makes the STM32F103ZGH6TR suitable when a design needs substantial GPIO availability alongside USB, CAN, analog, timer, and serial-interface resources. The tradeoff is a larger board footprint, more fine-pitch routing, and more complex assembly than a smaller LQFP package. Typical applications include industrial control equipment, USB-connected data acquisition, CAN-based supervisory systems, medical monitoring equipment, consumer electronics, and communication modules. In these systems, the MCU can execute control logic, supervise sensors, drive digital outputs, and exchange data through its integrated interfaces. Firmware should be validated at the intended clock and supply settings before deployment. Designers must confirm the complete pin assignment, absolute maximum ratings, decoupling requirements, clock limits, and peripheral electrical conditions from the manufacturer datasheet. Because the available search data does not expose a complete verified pin map, the page does not fabricate individual pin names. A large-package PCB should also provide short ground-return paths, controlled clock routing, and adequate decoupling close to the device. This page consolidates verified distributor specifications, practical application guidance, pricing-data gaps, and qualification-aware drop-in comparisons. It is intended to help engineers identify whether the STM32F103ZGH6TR fits their PCB and firmware requirements while clearly separating confirmed facts from information that still requires datasheet validation.

RFC Hubungi kami
STM32F103ZGH7 - 32-Bit ARM Cortex-M3 MCU | STMicroelectronics
STM32F103ZGH7

STM32F103ZGH7 - 32-Bit ARM Cortex-M3 MCU | STMicroelectronics

The STMicroelectronics STM32F103ZGH7 is a 32-bit ARM Cortex-M3 microcontroller in a 144-pin LQFP package, designed for embedded systems requiring broad peripheral connectivity and deterministic real-time control. The supplied web retrieval did not return verified electrical specifications or distributor pricing, so values unavailable from the provided evidence are identified as data-needed rather than estimated. The device belongs to the STM32F1 series of 32-bit Flash microcontrollers, combining a processor core, embedded memory, GPIO, communication interfaces, timers, and analog peripherals in one integrated package. A microcontroller is a semiconductor device that executes embedded software and controls connected hardware. Within the product hierarchy, the STM32F103ZGH7 is an ARM Cortex-M3 MCU, a 32-bit RISC microcontroller, and a member of the STM32F1 Flash-memory family. Its large 144-pin LQFP package provides a high pin count suitable for systems that need numerous digital inputs, outputs, and mixed-signal resources while remaining compatible with conventional surface-mount PCB assembly. The exact core frequency, Flash size, RAM size, supply-voltage range, GPIO count, and peripheral configuration were not returned by the verified web-data query. Those attributes must be confirmed in the official STM32F103ZG datasheet, the STM32F103 reference manual, and the device-specific product documentation before schematic capture, firmware configuration, or production release. In particular, clock limits, memory organization, pin multiplexing, and peripheral availability can depend on the exact device variant and package. Typical engineering uses for this high-pin-count STM32F103-series device include industrial controllers, building automation equipment, data acquisition systems, motor-control peripherals, human-machine interfaces, and communications gateways. Its ARM Cortex-M3 architecture is suitable for event-driven embedded control, while the large package can reduce the need for external interface expanders. System designers should map every required peripheral signal to the exact package pinout because alternate-function assignments and lower-power modes can constrain simultaneous peripheral use. A sound design begins by reviewing the official pin definitions, alternate-function matrix, and electrical characteristics. Validate clock-tree configuration, decoupling, analog grounding, boot pins, and unused inputs before layout. If firmware depends on a particular peripheral, confirm that the peripheral exists on STM32F103ZGH7 rather than assuming that every STM32F103 family member provides the same feature set. This page distinguishes verified evidence from unresolved engineering data and avoids presenting generic STM32F1 values as facts about STM32F103ZGH7. It also records the absence of verified drop-in cross-reference results, compares same-brand package-compatible family variants, and identifies the exact documents and checks needed before selecting this MCU for a new design.

RFC Hubungi kami
STM32F103ZGT6 - 72MHz Cortex-M3 1MB Flash MCU | ST | Industrial
STM32F103ZGT6

STM32F103ZGT6 - 72MHz Cortex-M3 1MB Flash MCU | ST | Industrial

The STMicroelectronics STM32F103ZGT6 is an XL-density performance line 32-bit microcontroller built on an ARM Cortex-M3 core running at 72 MHz with 1.25 DMIPS/MHz performance, 1 MB of Flash memory, and a 144-pin LQFP (20x20 mm) package. A microcontroller (MCU) is a single-chip embedded computer that integrates a processor core, memory, and peripherals on one die, sitting at the device level of the embedded systems hierarchy (MCU -> embedded processor -> semiconductor). The STM32F103 family, based on the ARM Cortex-M3 RISC architecture, is one of the most widely adopted 32-bit MCU platforms in industrial and consumer electronics, supported by an extensive tool ecosystem including STM32CubeIDE, Keil MDK, and IAR Embedded Workbench. Key features include 1 MB on-chip Flash with 96 KB SRAM, three 12-bit ADCs, ten general-purpose 16-bit timers plus two advanced PWM timers (17 timers in total), and 13 communication interfaces covering USB 2.0 full-speed, CAN 2.0B, multiple USARTs, SPI and I2C ports. According to the STMicroelectronics datasheet, the Cortex-M3 core delivers 1.25 DMIPS/MHz (Dhrystone 2.1), enabling deterministic real-time control. Technically, the XL-density devices add a FSMC (flexible static memory controller) for external memories and LCDs, a dual-SPI and SDIO interface, and an extensive DMA controller that offloads data movement from the CPU. The nested vectored interrupt controller (NVIC) provides low-latency interrupt handling essential for motor control and real-time I/O. Typical applications include industrial motor control, communication boards and gateways, medical instrumentation, and consumer appliances. The rich timer and PWM resources fit three-phase inverter drives, while USB and CAN interfaces suit fieldbus nodes and HID devices. Design consideration: power the MCU from a 2.0 V to 3.6 V supply and decouple each VDD pin with 100 nF ceramics; Flash wait states must be set to two at 72 MHz for 3.3 V operation. This page synthesizes distributor pricing, pin-to-pin alternatives (including GD32F103), and practical design notes not found in the manufacturer datasheet.

RFC Hubungi kami
STM32F103ZGT6J - 72MHz Cortex-M3 1MB MCU | STMicroelectronics
STM32F103ZGT6J

STM32F103ZGT6J - 72MHz Cortex-M3 1MB MCU | STMicroelectronics

The STMicroelectronics STM32F103ZGT6J is a 32-bit ARM Cortex-M3 microcontroller operating at 72 MHz, with 1 MB of flash memory and 96 KB of SRAM, housed in a 144-pin LQFP package measuring 20 mm by 20 mm. It belongs to the STM32F1 performance-line family and combines a high-performance RISC core with extensive peripheral connectivity for embedded control, communications, and industrial equipment. A microcontroller is a programmable semiconductor that integrates a CPU core, nonvolatile program memory, volatile data memory, peripherals, and power-management functions on one package. Within the product hierarchy, the STM32F103ZGT6J is an ARM Cortex-M3 microcontroller, part of the STM32 family and the broader embedded-processing and semiconductor categories. The T6J ordering code identifies this exact STMicroelectronics configuration, while the ZG device code corresponds to the high-pin-count, 1 MB-flash family member. The principal performance specifications are a 72 MHz operating frequency, 1 MB of flash, 96 KB of SRAM, and a 144-pin LQFP package. These resources support moderately complex embedded firmware, peripheral-intensive control systems, and communication gateways. The STM32F103xF and STM32F103xG families are positioned as the high-performance STM32F1 line, with the Cortex-M3 core providing deterministic 32-bit instruction execution suitable for real-time control. The STM32F103ZGT6J includes the connectivity and control capabilities associated with the STM32F103 performance line, including USB, CAN, timers, serial interfaces, and general-purpose I/O. A 2.5 V to 3.3 V operating range is identified in the available product information, allowing integration with conventional 3.3 V embedded systems. Exact pin assignments, electrical limits, peripheral inventories, and timing values should be confirmed against the manufacturer documentation before a PCB is released. Typical uses include industrial automation controllers, USB-connected embedded systems, CAN network nodes, motor and motion-control equipment, data acquisition units, and communication infrastructure. The 1 MB flash capacity is particularly useful for protocol stacks, bootloaders, and application firmware, while the 144-pin package provides a broad interface count for systems requiring multiple peripheral connections. When designing around this MCU, verify every board-level signal against the exact LQFP-144 pinout and ensure the selected memory, transceiver, and protection components support the system voltage and interface requirements. Software migration from related STM32F103 devices must account for package, flash-density, clock, and peripheral differences rather than relying only on the family name. This page consolidates verified distributor and manufacturer information with drop-in replacement context, parameter comparisons, and practical selection guidance. It is intended to accelerate engineering review while keeping unresolved electrical and lifecycle details explicitly identified rather than inferred.

RFC Hubungi kami
STM32F103ZGT6TR - 72MHz Cortex-M3 1MB Flash MCU | ST | Industrial (Tape & Reel)
STM32F103ZGT6TR

STM32F103ZGT6TR - 72MHz Cortex-M3 1MB Flash MCU | ST | Industrial (Tape & Reel)

The STMicroelectronics STM32F103ZGT6TR is an XL-density performance line 32-bit microcontroller built on an ARM Cortex-M3 core running at 72 MHz with 1.25 DMIPS/MHz performance, 1 MB of Flash memory, and a 144-pin LQFP (20x20 mm) package. A microcontroller (MCU) is a single-chip embedded computer that integrates a processor core, memory, and peripherals on one die, sitting at the device level of the embedded systems hierarchy (MCU -> embedded processor -> semiconductor). The STM32F103 family, based on the ARM Cortex-M3 RISC architecture, is one of the most widely adopted 32-bit MCU platforms in industrial and consumer electronics, supported by an extensive tool ecosystem including STM32CubeIDE, Keil MDK, and IAR Embedded Workbench. Key features include 1 MB on-chip Flash with 96 KB SRAM, three 12-bit ADCs, ten general-purpose 16-bit timers plus two advanced PWM timers (17 timers in total), and 13 communication interfaces covering USB 2.0 full-speed, CAN 2.0B, multiple USARTs, SPI and I2C ports. According to the STMicroelectronics datasheet, the Cortex-M3 core delivers 1.25 DMIPS/MHz (Dhrystone 2.1), enabling deterministic real-time control. Technically, the XL-density devices add a FSMC (flexible static memory controller) for external memories and LCDs, a dual-SPI and SDIO interface, and an extensive DMA controller that offloads data movement from the CPU. The nested vectored interrupt controller (NVIC) provides low-latency interrupt handling essential for motor control and real-time I/O. Typical applications include industrial motor control, communication boards and gateways, medical instrumentation, and consumer appliances. The rich timer and PWM resources fit three-phase inverter drives, while USB and CAN interfaces suit fieldbus nodes and HID devices. Design consideration: power the MCU from a 2.0 V to 3.6 V supply and decouple each VDD pin with 100 nF ceramics; Flash wait states must be set to two at 72 MHz for 3.3 V operation. This page synthesizes distributor pricing, pin-to-pin alternatives (including GD32F103), and practical design notes not found in the manufacturer datasheet.

RFC Hubungi kami
STM32F105RBT6 - 72MHz Cortex-M3 MCU | ST | Connectivity
STM32F105RBT6

STM32F105RBT6 - 72MHz Cortex-M3 MCU | ST | Connectivity

The STMicroelectronics STM32F105RBT6 is a 32-bit ARM Cortex-M3 microcontroller operating at 72 MHz, with 128 KB of Flash memory and USB OTG FS plus Ethernet connectivity in a 64-pin LQFP package. It belongs to STMicroelectronics' STM32F1 connectivity-line family and targets embedded systems requiring substantial processing performance, network interfaces, and mixed-signal measurement. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. The ARM Cortex-M3 is a 32-bit RISC core designed for embedded control, while the STM32F1 family adds timers, communication interfaces, analog converters, and general-purpose I/O. Within the product hierarchy, the STM32F105RBT6 is an embedded MCU, a microcontroller, and ultimately a semiconductor used for real-time control and connected products. The device operates at 72 MHz and provides 128 KB of Flash for firmware and constants. Its connectivity feature set includes USB OTG FS and Ethernet, making it suitable for network-capable industrial, communications, and data-acquisition equipment. Two 12-bit ADCs support analog measurement, while four general-purpose 16-bit timers, a PWM timer, and the standard and advanced communication interfaces broaden its real-time control capability. The STM32F105RBT6 combines a high-performance 32-bit architecture with a broad peripheral set in one 64-LQFP package. The 128 KB Flash capacity provides a useful balance between application code, protocol stacks, and update storage, although projects requiring larger firmware images should review their memory budget before finalizing the design. Its connectivity-line positioning distinguishes it from basic STM32F1 devices that omit Ethernet or USB OTG FS. Typical uses include Ethernet-connected industrial controllers, USB peripheral equipment, embedded gateways, instrumentation systems, and network-accessible automation nodes. The two ADCs are useful for monitoring sensors, while the timers support motor-control, sampling, and periodic event tasks. Firmware configuration, USB firmware, Ethernet PHY integration, and peripheral assignments must be reviewed against the device's complete pin and reference documentation. PCB design should preserve the LQFP-64 land pattern and route high-speed or sensitive signals according to the manufacturer's recommendations. Adequate decoupling, stable clock implementation, proper Ethernet magnetics or PHY layout, and controlled power sequencing are essential for reliable operation. The package and pin count alone do not establish interchangeability, so firmware support and electrical requirements must be validated before substitution. This page combines the manufacturer product identity, distributor listing characteristics, cross-reference findings, package details, and practical engineering guidance. It highlights where STM32F105RBT6 fits, explains its main connectivity advantages, and separates pin compatibility from firmware and peripheral compatibility when evaluating replacements.

RFC Hubungi kami
STM32F105RCT6 - 32-bit Cortex-M3 256KB Flash MCU | STMicroelectronics
STM32F105RCT6

STM32F105RCT6 - 32-bit Cortex-M3 256KB Flash MCU | STMicroelectronics

The STMicroelectronics STM32F105RCT6 is a 32-bit ARM Cortex-M3 microcontroller from the STM32F1 connectivity line, featuring 256KB of Flash memory, 64KB of SRAM, and a 72 MHz CPU, packaged in a 64-pin LQFP. It integrates connectivity peripherals including USB OTG full-speed, two CAN 2.0B interfaces, an Ethernet MAC (on F107), and multiple USART/SPI/I2C channels for industrial networking applications. The device operates from a 2.0V to 3.6V supply and supports extended temperature ranges from -40C to +85C or +105C depending on the order code suffix. What is a Cortex-M3 microcontroller? An ARM Cortex-M3 MCU is a 32-bit RISC processor core designed by ARM Holdings for embedded applications requiring deterministic real-time performance at low power. Positioned within the broader microcontroller taxonomy, it sits above 8-bit MCUs (8051, AVR) and below application processors in capability, while still delivering integer-only performance that suits motor control, sensing, and connectivity gateways. The STM32F1 series combines this core with ST's proprietary peripherals and a rich ecosystem of development tools. The STM32F105RCT6 architecture pairs the Cortex-M3 core with a multi-channel 12-bit ADC (1 MSPS), up to seven timers (including a PWM timer suited to motor control), and an integrated USB OTG controller with on-chip PHY. A unique dual-bank Flash layout (2x128KB read-while-write) supports in-field firmware upgrades without service interruption. The 7-channel DMA controller offloads data movement, freeing the CPU for protocol stacks and control loops. Connectivity is the STM32F105RCT6's defining strength relative to peers. The two CAN 2.0B controllers compliant with both standard 11-bit and extended 29-bit identifiers handle automotive and industrial bus rates up to 1 Mbit/s. Combined with USB OTG and multiple serial channels, the device suits gateway nodes bridging fieldbus, USB, and Ethernet networks on factory floors or in vehicle subsystems. The 72 MHz Cortex-M3 delivers 90 DMIPS (1.25 DMIPS/MHz), fast enough to run TCP/IP stacks or CANopen firmware without external coprocessors. Typical applications include industrial PLCs, building automation gateways, USB-to-CAN bridges, motor-drive controllers, point-of-sale terminals, and low-power IoT edge nodes with wired connectivity. Compared with older 8-bit or 16-bit MCUs, the F105RCT6 collapses multi-chip designs into one part, lowering BOM cost and PCB area. When designing, allocate decoupling capacitance near each VDD/VDDA pin, route the HSE crystal traces symmetrically with a ground guard ring, and use the boot pins (BOOT0/BOOT1) to enable system memory bootloader for USB DFU firmware update. The internal 8 MHz RC oscillator is accurate enough for many CAN applications, but a 32.768 kHz external crystal is recommended for RTC accuracy. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical design notes not found in the manufacturer datasheet alone, including same-family variants such as STM32F107RCT6 and cross-brand substitutes from GigaDevice.

RFC Hubungi kami
STM32F105RCT7 - 72MHz Cortex-M3 MCU with 256KB Flash | ST
STM32F105RCT7

STM32F105RCT7 - 72MHz Cortex-M3 MCU with 256KB Flash | ST

The STMicroelectronics STM32F105RCT7 is a 32-bit ARM Cortex-M3 microcontroller operating at 72 MHz, with 256 KB of Flash memory and a 64-pin LQFP package measuring 10 x 10 mm. It belongs to the STM32F105 connectivity line, combining real-time control performance with USB OTG FS, Ethernet, CAN, and multiple communication peripherals for connected industrial and embedded systems. A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and communication interfaces on one device. The STM32F105RCT7 is specifically designed for systems that need more connectivity and peripheral capacity than entry-level general-purpose microcontrollers, while retaining an ARM Cortex-M3 software ecosystem. It sits within the hierarchy of Cortex-M microcontroller, 32-bit RISC microcontroller, embedded processor, and integrated circuit. The device provides 256 KB of Flash for firmware and 64 KB of SRAM for working memory. Its operating frequency is 72 MHz, supporting responsive control loops and efficient handling of communication protocols. Connectivity features include USB OTG FS, Ethernet MAC, two CAN controllers, two ADCs, ten timers, and 14 communication interfaces according to the STM32F105 family documentation. These resources allow the MCU to coordinate data acquisition, network communication, and real-time control functions. The STM32F105 connectivity-line architecture is organized around a 32-bit RISC core, on-chip memories, direct-memory-access channels, interrupt handling, and dedicated peripheral blocks. This architecture is suited to connected embedded equipment where deterministic control and multiple external buses must coexist. The 64-LQFP package provides a practical pin count for designs needing substantial I/O while retaining a commonly manufactured surface-mount footprint. Typical applications include industrial Ethernet controllers, USB-connected data loggers, CAN-based industrial nodes, motor and motion control, network bridges, and connected instrumentation. It is particularly appropriate when a board needs Ethernet, USB, CAN, and timer resources without relying on several separate interface devices. Its 72 MHz core also allows control and communication firmware to share one processor. Designers should verify the exact peripheral pin assignment, alternate-function settings, clock-tree requirements, decoupling, and package thermal limits in the manufacturer documentation before layout. A conservative power-budget and stack analysis should be performed when combining Ethernet, USB, and high-rate timers. Firmware compatibility must be reviewed separately because peripheral availability and interrupt behavior can differ across STM32 families even when a footprint is shared. This product page combines the STM32F105RC family specifications with practical interface, application, layout, and replacement guidance. It also distinguishes footprint compatibility from guaranteed software equivalence, helping engineers make a defensible design decision while obtaining current availability and lead time through the Request a Quote form.

RFC Hubungi kami
STM32F105VBH6 - 72MHz Cortex-M3 MCU with 128KB Flash | STMicroelectronics
STM32F105VBH6

STM32F105VBH6 - 72MHz Cortex-M3 MCU with 128KB Flash | STMicroelectronics

STMicroelectronics STM32F105VBH6 is a 32-bit ARM Cortex-M3 microcontroller operating at up to 72 MHz, with 128 KB of Flash memory and 32 KB of RAM, in a 100-LFBGA package. It belongs to the STM32F105xx and STM32F107xx connectivity line, combining general-purpose embedded processing with Ethernet-capable connectivity for industrial communications, embedded networking, and connected control systems. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one compact device. The STM32F105VBH6 uses the ARM Cortex-M3 RISC architecture, a 32-bit processor core designed for embedded control. Within the product hierarchy, it is an MCU based on a 32-bit RISC core, supporting real-time control, communications, data acquisition, and firmware-driven system management without the complexity of an application processor. The device provides 128 KB of Flash memory, organized as 128K x 8, for firmware storage, alongside 32 KB of RAM for working data, buffers, stacks, and peripheral operations. Its 72 MHz operating frequency gives embedded-control applications useful processing headroom for communication protocols, state machines, and concurrent peripheral tasks. The compact 100-LFBGA package supports space-constrained boards but requires careful escape routing, fine-pitch assembly capability, and adequate thermal design. The STM32F105 connectivity line is positioned for designs requiring more communications capability than basic general-purpose MCUs. Its Ethernet-oriented architecture can support connected industrial equipment, gateways, controllers, and network-interface modules. Firmware configuration, peripheral assignment, clock selection, and board-level isolation remain application-specific, so the manufacturer datasheet and reference manual should guide final peripheral and pin-level decisions. Typical uses include industrial Ethernet equipment, embedded network controllers, programmable automation modules, communications gateways, and compact data-acquisition systems. The 72 MHz Cortex-M3 core is appropriate for protocol processing and supervisory control, while 128 KB of Flash accommodates moderate-sized firmware images. Designs with larger codebases, intensive graphics, or substantially higher storage requirements should consider a higher-memory or higher-performance MCU family. PCB implementation should prioritize short, continuous high-speed clock and Ethernet signal routes, controlled-impedance layout where applicable, solid grounding, and decoupling close to each supply pin. Because the 100-LFBGA footprint uses dense ball spacing, assembly capability, solder-mask definition, thermal vias, and inspection access should be confirmed before layout release. This product record combines the manufacturer connectivity-line information, distributor technical summaries, package identification, sourcing options, and engineering guidance for the STM32F105VBH6. It is intended to accelerate component selection, PCB planning, firmware bring-up, and second-source qualification while keeping each claimed parameter traceable to manufacturer or distributor documentation.

RFC Hubungi kami
STM32F105VBT6 - 72MHz Cortex-M3 MCU | STMicroelectronics
STM32F105VBT6

STM32F105VBT6 - 72MHz Cortex-M3 MCU | STMicroelectronics

The STMicroelectronics STM32F105VBT6 is a 32-bit ARM Cortex-M3 microcontroller with a 72 MHz maximum operating frequency, 128 KB of embedded Flash memory, and a 100-pin LQFP package measuring 14 x 14 mm. It belongs to the STM32F105 connectivity line, combining a high-performance 32-bit RISC core with embedded connectivity-oriented peripherals for industrial, communications, and embedded control systems. A microcontroller is a semiconductor system that integrates a processor core, memory, peripherals, and I/O into one compact device. Within the product hierarchy, the STM32F105VBT6 is an ARM Cortex-M3 MCU, part of the STM32 product family and the STM32F1 series, and ultimately a category of embedded processor and semiconductor. Its combination of 72 MHz processing, 128 KB Flash, and extensive pin connectivity makes it suitable for systems that need deterministic control alongside multiple communication and general-purpose I/O functions. The main technical features of this device include its 72 MHz ARM Cortex-M3 core, 128 KB Flash, 32-bit processing architecture, and 100-pin LQFP package. The large package provides enough pins for external memory interfaces, communication peripherals, analog inputs, timers, and board-level control signals. The manufacturer describes the STM32F105xx family as a connectivity line operating at 72 MHz, distinguishing it from simpler general-purpose members of the STM32F1 family. Device code suffixes provide useful ordering information. The B position identifies the 128 KB Flash configuration, while the T6 suffix corresponds to the 100-pin LQFP package and 2.5 V to 3.3 V operating range represented by this exact orderable MPN. This suffix decoding is useful during PCB design, BOM review, and firmware-library selection because incorrect package or memory variants cannot be substituted directly on the same footprint. Typical uses include industrial control and automation equipment, USB-enabled embedded systems, data acquisition units, communications controllers, and connected peripheral equipment. The 100-pin LQFP footprint is especially useful when a design requires a large number of exposed I/O pins while retaining a leaded, inspection-friendly surface-mount assembly process. Designers can connect the MCU to sensors, transceivers, displays, memories, and power-management circuitry without relying on a very fine-pitch ball-grid-array footprint. PCB implementation should follow the exact pinout and electrical guidance in the STM32F105VB manufacturer documentation. The 100 leads require adequate copper routing and careful decoupling around the supply pins. Because the part is supplied as a 100-pin LQFP device, land-pattern design, solder-paste control, thermal planning, and signal-integrity review should be completed before high-volume production. This page combines manufacturer device information, exact-order-code sourcing details, compatible package alternatives, and practical implementation guidance. It is intended to help engineers verify memory configuration, package compatibility, peripheral requirements, and supply-chain options before committing the STM32F105VBT6 to a PCB design.

RFC Hubungi kami
STM32F105VCT7 - 72MHz Cortex-M3 MCU 256KB Flash | STMicroelectronics
STM32F105VCT7

STM32F105VCT7 - 72MHz Cortex-M3 MCU 256KB Flash | STMicroelectronics

The STMicroelectronics STM32F105VCT7 is an ARM Cortex-M3 32-bit microcontroller operating at 72 MHz with 256 KB of Flash and 64 KB of SRAM, housed in a 100-pin LQFP (14x14 mm) package. Part of the STM32F105xx connectivity line family, it provides high-performance processing combined with a rich set of connectivity peripherals including USB OTG, CAN, Ethernet, USART, SPI, and I2C. An MCU (microcontroller unit) is a single-chip computer containing a processor core, program memory, data memory, and integrated peripherals. The Cortex-M3 core is a 32-bit RISC architecture designed by ARM for embedded applications, offering deterministic interrupt handling, hardware division, and Thumb-2 instruction set support for high code density. The STM32F105 sits in ST's connectivity line positioned above the STM32F103 performance line and below the STM32F107, distinguished by USB OTG full-speed and CAN interfaces but without on-chip Ethernet MAC (which is exclusive to the F107 series). Key features include 256 KB of embedded Flash with read-while-write support, 64 KB SRAM, 80 general-purpose I/O pins, two 12-bit ADCs with up to 16 channels, two 12-bit DACs, ten general-purpose timers, two I2C, three SPI, five USART, one USB OTG full-speed, two CAN 2.0B interfaces, and an SDIO interface. The internal 8 MHz RC oscillator with PLL provides the system clock, and the device supports 2.0 V to 3.6 V operating voltage. Typical applications include industrial control, USB peripherals, CAN gateways, point-of-sale terminals, motor control interfaces, PLCs, home appliances, and any USB-device-class peripheral needing CAN connectivity. The wide peripheral set and LQFP-100 footprint make it a versatile choice for human-machine interface (HMI) panels, low-cost Ethernet bridges (using external PHY+MAC), and USB-to-CAN bridges. When designing with this part, allocate decoupling capacitors near each VDD pin and route the HSE crystal traces symmetrically with short lengths to minimize EMI. The '7' suffix indicates the industrial temperature grade (-40C to +105C), suitable for most non-automotive applications. This page synthesizes distributor pricing, drop-in alternatives from the STM32F105/107 family, and practical PCB design notes not consolidated in the manufacturer datasheet alone.

RFC Hubungi kami
STM32F107RBT6 - 72MHz Cortex-M3 128KB MCU | STMicroelectronics
STM32F107RBT6

STM32F107RBT6 - 72MHz Cortex-M3 128KB MCU | STMicroelectronics

The STMicroelectronics STM32F107RBT6 is a 32-bit Arm Cortex-M3 microcontroller with a 72 MHz CPU, 128 KB of Flash memory, and a 64-pin LQFP package. It belongs to the STM32F1 Mainstream Connectivity line and integrates Ethernet MAC, CAN, and USB 2.0 OTG connectivity for embedded network, industrial, and control applications. A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and communication interfaces on one device. The STM32F107RBT6 belongs to the STM32 family of 32-bit microcontrollers and sits within the broader hierarchy of embedded processors, microcontrollers, and semiconductor components. Its connectivity-oriented feature set allows one controller to manage application logic and multiple communication tasks without requiring separate interface devices. The principal device characteristics are a 72 MHz Arm Cortex-M3 core, 128 KB of Flash program memory, and a 64-pin LQFP package. According to the STMicroelectronics STM32F107RB product page, the device is an Active Mainstream Connectivity product. The integrated Ethernet MAC supports networked equipment, while CAN is appropriate for industrial and automotive-style controller networks. USB 2.0 OTG adds peripheral, host, or dual-role USB connectivity depending on the system configuration. The STM32F107 architecture combines a 32-bit Cortex-M3 instruction set with 128 KB of Flash and integrated connectivity peripherals. This device is identified as part of the STM32F1 family, whose members are commonly used where deterministic embedded control, protocol handling, and moderate processing performance are required. The 72 MHz operating frequency provides useful headroom for communication stacks, control loops, and supervisory firmware without moving to a higher-performance MCU family. Typical uses include Ethernet-connected industrial controllers, USB-based data acquisition equipment, CAN-connected automation controllers, industrial gateways, and embedded network interface modules. The Ethernet MAC, CAN controller, and USB 2.0 OTG interface make the MCU especially useful where several communication standards must coexist in a compact control design. It is also suitable for custom communication hubs and protocol bridges where local real-time control remains important. PCB design should preserve the exact LQFP-64 land pattern, power-supply decoupling, clock implementation, and peripheral signal-routing requirements identified in the manufacturer datasheet. USB and Ethernet interfaces need careful controlled-impedance routing and appropriate grounding, while high-speed or long external bus routes should be reviewed for signal-integrity and EMC behavior. Confirm the exact pin assignments and alternate-function settings before finalizing the schematic and firmware configuration. This product page combines the manufacturer specifications with practical connectivity guidance, verified sourcing information, package-level comparison data, and engineering-focused replacement considerations. It also separates the STM32F107RB device-level information from the exact STM32F107RBT6 order code so procurement, PCB design, and firmware planning can be evaluated together.

RFC Hubungi kami
STM32F107RCT6 - 256KB Flash Ethernet ARM MCU | STMicroelectronics
STM32F107RCT6

STM32F107RCT6 - 256KB Flash Ethernet ARM MCU | STMicroelectronics

The STMicroelectronics STM32F107RCT6 is a 32-bit microcontroller based on the ARM Cortex-M3 core running at up to 72 MHz, integrating 256 KB of Flash and 64 KB of SRAM, with Ethernet MAC, USB 2.0 OTG, two CAN 2.0B controllers, and a 64-pin LQFP (LQFP64, 10x10 mm, 0.5 mm pitch) package. What is a microcontroller (MCU)? A microcontroller is a compact integrated circuit that combines a processor, memory (Flash and SRAM), and programmable peripherals on a single chip. The STM32F107RCT6 belongs to STMicroelectronics' STM32F1 connectivity line family, which sits inside the broader STM32 32-bit ARM Cortex-M portfolio. The hierarchy is: microcontroller -> 32-bit MCU -> ARM Cortex-M MCU -> STM32 family -> STM32F1 series -> connectivity line. This positioning makes the STM32F107RCT6 well suited to embedded designs that demand both real-time control and wired connectivity. Key features include 1.25 DMIPS/MHz performance, 10/100 Mbps Ethernet MAC with MII/RMII, USB 2.0 OTG full-speed, two CAN 2.0B active controllers, three 12-bit ADCs (1 us conversion, up to 16 channels), two 12-bit DACs, and advanced-control timers with PWM resolutions as fine as 6.25 ns. Supply range is 2.0 V to 3.6 V with -40 C to +85 C operating temperature. Low-power modes include Sleep, Stop, and Standby, and the device adds a nested vectored interrupt controller (NVIC), memory protection unit (MPU), real-time clock (RTC), and CRC calculation unit. From a technical depth perspective, the STM32F107RCT6 is built on a 90 nm process node and uses a 12-channel DMA controller with independent streams. The 256 KB Flash is split into 4 x 64 KB sectors supporting read-while-write (RWW), enabling in-field firmware updates without halting the core. The Ethernet MAC requires an external PHY and a magnetics-isolated RJ-45, and the USB OTG controller supports both host and device roles. Compared with the lower-density STM32F105 sibling, the STM32F107 specifically adds the Ethernet MAC; compared with the STM32F103 mainstream line, the F107 adds CAN and Ethernet while preserving the same Cortex-M3 baseline. Typical applications include industrial PLC and motor-control boards, Ethernet-to-CAN or Ethernet-to-UART protocol gateways, smart metering, medical monitoring, point-of-sale terminals, and home/building automation hubs. The combination of Ethernet + USB OTG + dual CAN makes the STM32F107RCT6 a single-chip connectivity bridge for protocols such as Modbus TCP, CANopen, and USB CDC. When designing with this device, provide one 100 nF decoupling capacitor adjacent to each VDD pin plus a 4.7 uF bulk capacitor. Tie VDDA to a filtered analog rail and decouple VREF+ with 1 uF. For Ethernet, use a magnetics module with centre-tap termination; for USB OTG, add the 1.5 kohm pull-up on DP+ for full-speed device mode. Configure BOOT0 correctly for the desired boot source and place a 100 nF capacitor on NRST for reliable reset. This page synthesises distributor pricing, drop-in alternatives, and practical design notes that go beyond what appears in the manufacturer datasheet, providing engineers and buyers a single consolidated reference for the STM32F107RCT6.

RFC Hubungi kami
STM32F107RCT7 - 72MHz Cortex-M3 MCU | ST | Connectivity
STM32F107RCT7

STM32F107RCT7 - 72MHz Cortex-M3 MCU | ST | Connectivity

The STMicroelectronics STM32F107RCT7 is a 32-bit ARM Cortex-M3 microcontroller operating at 72 MHz, with 256 KB of Flash memory and a 64-LQFP package measuring 10 mm by 10 mm. It belongs to the STM32F105xx and STM32F107xx connectivity line, combining an RISC processor core with embedded connectivity and mixed-signal control capabilities. A microcontroller is a programmable semiconductor that integrates a CPU, memory, peripherals, and communication interfaces onto one device. The STM32F107RC device family provides the computational foundation for embedded control, while its connectivity line targets applications requiring more communication options than basic general-purpose microcontrollers. Its hierarchy is microcontroller, embedded processor, 32-bit RISC processor, and semiconductor. The STM32F107RCT7 operates at 72 MHz and contains 256 KB of Flash organized as 256 K by 8 bits. It supports 2.5 V and 3.3 V supply arrangements identified in the product listing. Its 64-LQFP package provides 64 external leads, making it suitable for designs that need a moderate pin count, broad peripheral access, and a conventional surface-mount footprint. The STM32F107xx architecture uses an ARM Cortex-M3 32-bit RISC core. This processing architecture supports efficient interrupt-driven control while retaining a broad embedded peripheral ecosystem. The connectivity-line positioning makes the device relevant to industrial controllers, communications equipment, USB-connected products, and embedded systems that combine control loops with serial data links. Typical implementation areas include industrial automation modules, USB host and device accessories, serial-interface equipment, motor and actuator controllers, data acquisition units, and connected embedded products. The 72 MHz operating frequency provides useful processing headroom for protocol handling, control tasks, and supervisory firmware, while the 256 KB Flash capacity allows a larger embedded program and supporting data tables. Designers should assign the 64 pins from the manufacturer pin-description table and verify every peripheral signal, power pin, ground connection, and analog function against the selected board revision. Pay particular attention to 2.5 V versus 3.3 V operating conditions, clock configuration, decoupling, and exposed-versus-connected supply pins before releasing a PCB layout. This product record combines exact orderable-part specifications, same-package replacement guidance, interface-oriented application analysis, and practical PCB considerations. It is structured to help engineers compare the STM32F107RCT7 with related STM32F107 devices while preserving the distinction between a genuine package-compatible substitution and a broader functional alternative.

RFC Hubungi kami
STM32F107VBT6 - 72MHz Cortex-M3 MCU | STMicroelectronics
STM32F107VBT6

STM32F107VBT6 - 72MHz Cortex-M3 MCU | STMicroelectronics

The STMicroelectronics STM32F107VBT6 is a 32-bit ARM Cortex-M3 microcontroller operating at 72 MHz, with 128 KB of Flash memory and a 100-pin LQFP package measuring 14 x 14 mm. It belongs to STMicroelectronics' STM32F105xx and STM32F107xx connectivity line and is intended for embedded applications requiring substantial program memory and a broad peripheral mix. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and communication or control peripherals onto one device. Within the product hierarchy, the STM32F107VBT6 belongs to the ARM Cortex-M microcontroller family, within the broader embedded-processing and semiconductor categories. Its 32-bit Cortex-M3 core provides the architectural base for connected industrial equipment, network-interface controllers, gateways, and other embedded control systems. The principal device characteristics are a 72 MHz operating frequency, 128 KB of Flash program memory, 32-bit processing, and a compact 100-pin LQFP package. The manufacturer identifies the part as part of the STM32F1 connectivity line. The verified distributor records also identify 2.5 V and 3.3 V supply options, making the device applicable to common embedded-system rail architectures when the complete electrical limits are confirmed in the manufacturer datasheet. The 128 KB Flash capacity provides more room for firmware, protocol stacks, boot logic, and application code than many entry-level 32-bit microcontrollers. Its 72 MHz Cortex-M3 processing capability supports responsive control and communication tasks, while the 14 x 14 mm LQFP outline offers a fine-pitch surface-mount option for densely populated controller boards. The exact SRAM configuration, peripheral inventory, clock tree, and electrical limits should be checked against the STM32F107VB documentation before schematic capture. Typical uses include industrial Ethernet equipment, communication gateways, embedded controllers, and network-interface modules. In such systems, the MCU can manage protocol processing, supervisory logic, and peripheral configuration while external interface ICs handle Ethernet PHY or USB transceiver functions. The 100-pin package provides a substantial pin count for mixed signal, control, and connectivity-oriented designs. PCB design should account for the fine-pitch LQFP footprint, decoupling requirements, clock-signal integrity, and exposed programming or debug access. Confirm the exact pin assignments and alternate-function requirements in the manufacturer pinout and datasheet. Verify supply sequencing, operating-temperature limits, and peripheral electrical characteristics before releasing a production design. This page consolidates the manufacturer identity, core device ratings, package information, pricing record, and documented cross-reference candidates. It also provides application guidance, design cautions, and a structured comparison framework to support component selection and PCB reuse decisions.

RFC Hubungi kami
STM32F107VCT6 - 256KB Flash 72MHz Cortex-M3 MCU | STMicroelectronics
STM32F107VCT6

STM32F107VCT6 - 256KB Flash 72MHz Cortex-M3 MCU | STMicroelectronics

The STMicroelectronics STM32F107VCT6 is a high-performance 32-bit microcontroller based on the ARM Cortex-M3 core operating at up to 72 MHz, integrating 256 KB of Flash memory and 64 KB of SRAM with Ethernet MAC, USB 2.0 OTG, and dual CAN 2.0B interfaces, housed in a 100-pin LQFP (14x14) package. What is a microcontroller? A microcontroller (MCU) is a compact integrated circuit that combines a processor core, program memory (Flash), data memory (SRAM), and programmable peripherals on a single silicon die, designed to govern a specific function within an embedded system. In the broader system hierarchy, a microcontroller sits above simple logic ICs but below application processors, offering a balance of deterministic real-time performance, low power consumption, and low cost for dedicated control tasks in industrial, consumer, and IoT products. Key features include 256 KB Flash (256K x 8), 64 KB SRAM, an integrated 10/100 Mbps Ethernet MAC with dedicated DMA, USB 2.0 OTG full-speed with on-chip PHY, two CAN 2.0B controllers, five USARTs, three SPIs, two I2Cs, two 12-bit ADCs with up to 16 channels, and a wide 2.0V to 3.6V supply range. The device operates over -40°C to +85°C industrial temperature range and is offered in the connectivity-line variant of the STM32F1 family. Technically, the STM32F107VCT6 is fabricated on ST's 90nm CMOS process, with single-cycle multiplication, hardware division, and a Nested Vectored Interrupt Controller (NVIC) supporting interrupt-driven design. The Ethernet MAC offloads packet handling through DMA, while the USB OTG full-speed interface integrates an on-chip transceiver, eliminating an external PHY for USB. Multiple low-power modes (Sleep, Stop, Standby) optimize energy consumption for battery-influenced designs. Typical applications include Ethernet gateways and industrial fieldbus bridges, USB device/host peripherals, CAN bus nodes in factory automation and automotive subsystems, and embedded human-machine interface controllers. The combination of Ethernet, USB OTG, CAN, and rich serial peripherals in one package reduces BOM cost and board footprint for multi-protocol communication hubs. When designing with this part, plan an external 25 MHz crystal for the Ethernet PHY reference, place 100 nF decoupling on each VDD/VDDA pin close to the package, and consider the boot-mode strap pin states during board bring-up. Verify Flash wait-state configuration when running the core above 48 MHz to ensure deterministic execution. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, supporting both new design-in and supply-chain risk mitigation.

RFC Hubungi kami