Produk (44,000+)

INA111BUG4 - 2MHz FET-Input Instrumentation Amp | Texas Instruments
INA111BUG4

INA111BUG4 - 2MHz FET-Input Instrumentation Amp | Texas Instruments

The Texas Instruments INA111BUG4 is a high-speed, FET-input instrumentation amplifier with a gain-bandwidth product of 2 MHz, packaged in a 16-pin SOIC. It is designed for precision signal-conditioning applications that require amplification of low-level differential signals, particularly when the source impedance is high and input bias current must remain small. An instrumentation amplifier is a specialized analog amplifier that measures the voltage difference between two inputs while rejecting common-mode interference. The INA111 belongs to the FET-input instrumentation amplifier hierarchy, combining an instrumentation amplifier with low-bias-current transistor input circuitry. This topology supports accurate measurement from sources that would disturb conventional bipolar-input amplifiers. The INA111’s principal advantages include input bias current below 20 pA, operation across a -40°C to +85°C temperature range, and a 2 MHz gain-bandwidth product. Its FET inputs also reduce input loading, simplify input filtering, and make the device suitable for bridge, transducer, and current-sense measurements where source impedances range from approximately 2 kΩ to 50 kΩ. The SOIC-16 surface-mount package supports compact analog instrumentation. The three-op-amp instrumentation-amplifier architecture provides a practical balance between common-mode rejection, gain control, input impedance, and signal bandwidth. Gain is established externally, allowing one device to support multiple measurement ranges without changing its internal signal path. As with any precision amplifier, the useful bandwidth decreases as the selected gain increases, so the complete gain-versus-bandwidth characteristic must be considered in high-speed designs. Typical uses include bridge-transducer excitation and readout, precision current sensing, laboratory measurement interfaces, medical instrumentation, and low-level differential signal acquisition. The high input impedance is particularly useful when the source is a sensor or resistive network whose output impedance is much higher than the amplifier input resistance. The device can therefore preserve source amplitude and reduce loading errors. For reliable operation, place the external gain-setting resistor and compensation network close to the device, keep input and feedback traces short, and use a quiet, low-impedance supply. Decoupling capacitors should be positioned directly beside the supply pins, while analog and digital ground returns should follow the manufacturer’s recommended layout and grounding arrangement. This product page combines the manufacturer’s INA111 documentation with application guidance, package information, verified source links, and replacement considerations. It is intended to help engineers identify suitable signal-chain applications, evaluate package and lifecycle constraints, and determine whether an existing PCB footprint can be reused without changing the analog layout.

RFC Hubungi kami
INA114AP - 1MHz Precision Instrumentation Amplifier | Texas Instruments
INA114AP

INA114AP - 1MHz Precision Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA114AP is a precision instrumentation amplifier featuring 1 MHz bandwidth, 50 µV maximum offset voltage, 11 nV/√Hz input noise, and approximately 3 mA operating current in an 8-pin PDIP package. It is designed for low-level differential measurements where sensor outputs are small and common-mode voltage, noise, and offset must be controlled carefully. The INA114AP uses a general-purpose three-op-amp architecture that accepts differential input signals and provides a scaled, referenced output for downstream conversion or control. An instrumentation amplifier is a specialized analog amplifier that measures the voltage difference between two inputs while rejecting common-mode voltage and providing controlled gain. The INA114 family belongs to the broader operational amplifier hierarchy as an instrumentation amplifier, precision analog IC, signal-conditioning IC, and power-management-dependent semiconductor device. This makes it suitable for bridge sensors, load cells, thermocouples, current shunts, and other transducers whose useful output occupies only a small portion of the applied voltage. The key electrical benefits of the INA114AP include a 1 MHz gain-bandwidth product, maximum input offset voltage of 50 µV, maximum offset drift of 0.25 µV/°C, maximum input bias current of 2 nA, and common-mode rejection of at least 115 dB. Its input-noise density is 11 nV/√Hz, making it effective for low-amplitude signals where broadband amplifier noise would otherwise obscure the measurement. Input overvoltage protection extends to ±40 V, while the supply range reaches ±18 V. These characteristics provide useful headroom in industrial and measurement systems where input transients and supply variations must be tolerated. The three-op-amp instrumentation-amplifier architecture supports accurate differential measurement with adjustable gain. A differential signal applied across the input terminals is amplified relative to ground or the voltage connected to the reference terminal. The gain depends on the external resistor connected to the gain-control pins, allowing the same device family to serve multiple transducer sensitivities. The 1 MHz bandwidth makes it suitable for applications extending beyond static measurement, including moderate-rate sensor acquisition and feedback control. Typical uses include load-cell and weighing systems, strain-gauge bridges, thermocouple interfaces, industrial pressure and flow sensors, biomedical instrumentation, and current-shunt measurements. The combination of low offset, high common-mode rejection, and low bias current is particularly valuable when the sensor is physically remote or when its leads pick up industrial noise. The 115 dB minimum common-mode rejection helps preserve a small differential signal even when both inputs ride on a larger common-mode voltage. A successful design must include adequate bypassing, careful routing of the two input paths, and a stable gain resistor. Place the input and supply capacitors close to their associated pins, keep the two input traces symmetrical, and avoid routing sensitive signals beside high-current or switching nodes. Select the gain resistor with suitable tolerance and temperature coefficient, and verify input and output swing against the actual sensor range. When the source impedance is high, account for amplifier bias-current error before interpreting the measured differential voltage. This page combines manufacturer specifications, exact-source pricing eligibility, package-level pin information, application guidance, and confirmed drop-in alternatives. It also highlights the distinction between a true same-footprint replacement and a merely similar instrumentation amplifier, helping engineers compare parts without relying on an incomplete cross-reference list.

RFC Hubungi kami
INA114AU - 1MHz Precision INA Amplifier | Texas Instruments
INA114AU

INA114AU - 1MHz Precision INA Amplifier | Texas Instruments

Texas Instruments INA114AU is a precision, single-amplifier instrumentation amplifier with 1 MHz gain-bandwidth product, 50 µV maximum offset voltage, 11 nV/√Hz input noise, and 3 mA power consumption, housed in a 16-pin SOIC package. It supports dual supplies of ±2.25 V to ±18 V, provides internal input protection to ±40 V, and accepts a single gain-setting resistor for gains from 1 to 10,000. An instrumentation amplifier is a specialized amplifier that measures small differential signals while rejecting large common-mode voltages. The INA114 belongs to the precision instrumentation-amplifier hierarchy, where instrumentation amplifier, differential amplifier, analog signal-conditioning IC, and power-management-adjacent signal-chain component describe its principal function. Its three-op-amp architecture provides high input impedance and accurate differential gain, making it useful when the source resistance can vary or when a conventional op-amp differential circuit would suffer input-bias-current errors. Key features include 50 µV maximum offset voltage, 0.25 µV/°C maximum offset drift, 2 nA maximum input bias current, and 115 dB minimum common-mode rejection. A single external resistor selects gains from 1 to 10,000, while the 1 MHz gain-bandwidth product supports a 0.06 V/µs slew rate. These characteristics favor precision measurement rather than high-speed video amplification, although the 1 MHz bandwidth is sufficient for many industrial, medical, and instrumentation signals. The INA114 uses a three-op-amp internal architecture to establish differential gain while maintaining high input impedance. Laser trimming reduces offset errors, and the internal input protection network allows each input to withstand ±40 V without damage. With a typical 3 mA quiescent-current specification and operation down to ±2.25 V, the device supports dual-supply precision systems and single 5 V applications using suitable output-reference arrangements. Typical uses include bridge and strain-gauge conditioning, current-shunt measurement, laboratory instrumentation, ECG and physiological-signal acquisition, and industrial sensor interfaces. In a bridge circuit, the low offset and high common-mode rejection improve stability in the presence of long cables or supply variation. For sensor excitation, the amplifier converts a small millivolt-level differential output into a voltage suitable for an ADC. Designers must select the gain resistor carefully because its tolerance, temperature coefficient, and parasitic capacitance affect gain accuracy and bandwidth. Decoupling capacitors should be placed close to the supply pins, and the reference pin should be configured to provide the required output offset. Input filtering must preserve the required settling time because the internal protection resistors can combine with source capacitance to alter bandwidth. This product record consolidates verified manufacturer specifications, distributor information, drop-in alternatives, package details, and application guidance. It highlights the engineering trade-offs among gain, bandwidth, input protection, common-mode rejection, and supply requirements that are not apparent from the MPN alone.

RFC Hubungi kami
INA114AU/1K - 1MHz Precision Instrumentation Amplifier | TI
INA114AU/1K

INA114AU/1K - 1MHz Precision Instrumentation Amplifier | TI

Texas Instruments INA114AU/1K is a single-channel precision instrumentation amplifier featuring 1 MHz gain-bandwidth product, 50 µV typical offset voltage, 11 nV/√Hz input noise density, and 3 mA power consumption. The device is packaged in a 16-pin SOIC and accepts supply voltages as low as ±2.25 V. A single external resistor sets the gain from 1 to 10,000, allowing the same circuit topology to serve low-gain signal conditioning and high-gain bridge-amplifier applications. An instrumentation amplifier is a specialized analog signal-conditioning IC designed to amplify the voltage difference between two inputs while rejecting common-mode signals. Its typical hierarchy is instrumentation amplifier → differential amplifier → analog amplifier → semiconductor. This category is especially useful when a low-level sensor output must be measured in the presence of a larger shared voltage. The INA114 uses a three-op-amp architecture, which provides high input impedance, flexible gain control, and accurate differential amplification. The INA114's principal electrical features include a 1 MHz gain-bandwidth product, 110 dB dynamic range as identified in the manufacturer listings, 50 µV typical offset, and 11 nV/√Hz input noise density. A single gain-setting resistor establishes gains between 1 and 10,000, eliminating the need for a resistor network. The device can operate with power supplies as low as ±2.25 V and supports dual supplies up to ±18 V. Internal input protection can withstand input voltages up to ±40 V without damage, adding robustness in industrial measurement systems. Internally, the INA114 uses a versatile three-op-amp instrumentation-amplifier arrangement. Its input stage preserves the differential signal while the output stage develops the selected gain and drives the output relative to the REF pins. The laser-trimmed internal resistors support low offset and consistent performance without user calibration. The manufacturer identifies the INA114 as a low-cost, general-purpose precision device, while its 1 MHz bandwidth allows it to handle signals substantially faster than static low-frequency sensor outputs. Typical uses include bridge and strain-gauge signal conditioning, current-shunt measurement, low-level sensor interfaces, laboratory instrumentation, and industrial process-control inputs. It is particularly appropriate when a sensor develops only millivolts or microvolts and common-mode voltage can be much larger than the desired signal. The adjustable gain also supports transducers with widely different output sensitivities without changing the surrounding analog topology. When laying out the circuit, connect the gain resistor between the designated RG pins and place input, supply, and reference bypassing capacitors close to the associated package pins. Keep sensitive input traces short, route them away from switching nodes, and use a stable low-noise reference when an offset voltage other than ground is required. Confirm input and output common-mode ranges over the complete supply range because the selected gain reduces allowable output swing. This page combines manufacturer specifications, exact-order information, a same-package electrical alternative, and practical design guidance. It also distinguishes reel-packaged ordering variants from genuinely different functions, helping engineers make a defensible selection without relying on package code alone.

RFC Hubungi kami
INA114BP - 1MHz Precision Instrumentation Amplifier | TI
INA114BP

INA114BP - 1MHz Precision Instrumentation Amplifier | TI

Texas Instruments INA114BP is a precision three-op-amp instrumentation amplifier with a 1 MHz gain-bandwidth product, 50 uV maximum offset voltage, and an 8-pin PDIP package. It supports gains from 1 to 10,000 through one external gain-setting resistor, while input protection tolerates voltages up to +/-40 V. Its low-noise and high-accuracy characteristics make it suitable for measuring small differential signals in industrial, medical, and test systems. An instrumentation amplifier is a specialized amplifier category designed to extract a small differential voltage while rejecting common-mode interference. Its internal three-op-amp architecture provides high input impedance and precise gain control, making it more effective than ordinary operational amplifiers in many sensor-front-end applications. Within the signal-chain hierarchy, it belongs to the broader family of amplifier ICs and analog signal-conditioning components. Key features include 11 nV/sqrt(Hz) input noise, 115 dB minimum common-mode rejection, 2 nA maximum input bias current, and 0.25 uV/degree C maximum input offset drift. The low offset voltage and drift reduce measurement errors in bridge, strain-gauge, and low-level current sensing systems. Internal input protection supports +/-40 V, helping the device tolerate transient overloads encountered outside the normal operating input range. The INA114 uses a versatile three-op-amp signal chain and accepts single or dual supply operation. Its gain is established with one external resistor, allowing a single circuit implementation to cover gain settings from 1 to 10,000. The 1 MHz bandwidth supports dynamic sensor signals while remaining appropriate for precision industrial instrumentation rather than very high-frequency signal extraction. Typical uses include 4-20 mA current-loop receivers, strain-gauge bridge amplifiers, isolated-signal front ends, precision current-shunt measurements, biomedical instrumentation, and laboratory measurement equipment. The device is particularly useful when the wanted differential signal is small relative to ground offsets or common-mode noise present at the input connectors. When designing the input stage, use an external gain resistor with suitable stability and thermal characteristics, keep input traces short, and connect the reference pin to a clean analog ground when unity gain is required. Check input common-mode range and output swing at every supply voltage before selecting the final gain, because bandwidth and output capability change with operating conditions. This page combines the device's precision specifications, application guidance, package information, replacement analysis, and practical design considerations to support faster component evaluation and more reliable front-end design.

RFC Hubungi kami
INA114BU - 1MHz Precision Instrumentation Amplifier | TI
INA114BU

INA114BU - 1MHz Precision Instrumentation Amplifier | TI

Texas Instruments INA114BU is a precision three-op-amp instrumentation amplifier with 1 MHz gain-bandwidth performance, 50 uV input-offset voltage, 11 nV/√Hz input noise, and approximately 3 mA power consumption. The device is offered in a 16-pin SOIC surface-mount package for precision measurement systems requiring differential input amplification and single-resistor gain programming. An instrumentation amplifier is a specialized analog amplifier optimized for measuring small differential signals superimposed on large common-mode voltages. It belongs to the amplifier hierarchy as an instrumentation amplifier, differential amplifier, and analog signal-conditioning IC. Its internal three-op-amp architecture improves common-mode rejection and enables gains from 1 to 10,000 by selecting one external gain-setting resistor. This makes the INA114BU useful when a sensor, transducer, or measurement bridge produces a low-level differential output that must be amplified without amplifying system noise or supply variation equally. The most prominent INA114BU characteristics are its 1 MHz bandwidth, 50 uV offset voltage, and 11 nV/√Hz noise density. The single external gain resistor simplifies adjustment while preserving a broad usable gain range. Input protection can withstand voltages to ±40 V, helping the amplifier tolerate moderate overvoltage conditions. A 2.25 V to 18 V supply range supports both low-voltage and conventional industrial analog systems, while the approximately 3 mA supply-current figure supports low-power instrumentation. The INA114BU uses a versatile three-op-amp instrumentation-amplifier architecture. Its gain is established by the external resistor connected to the gain-setting node, avoiding the need for matched resistor networks. Input and feedback resistors are integrated internally, while the specified input-noise and offset characteristics support accurate extraction of small differential signals. The 1 MHz bandwidth allows the amplifier to process signals beyond static or very-low-frequency measurement tasks while retaining a compact analog implementation. Typical uses include bridge-based pressure and load sensing, biomedical instrumentation, current-shunt measurement, laboratory test equipment, and industrial process-control front ends. The 16-pin SOIC package is useful where moderate pin count, surface-mount assembly, and access to a conventional package are preferred. Its ±40 V input-protection capability is especially relevant when a sensor line can experience transient or sustained voltage excursions. Circuit design should begin with the required gain and bandwidth. Because gain is set by one resistor, verify its noise contribution, tolerance, and stability alongside the sensor source impedance. Keep input and feedback routing short, use a clean low-noise ground reference, and place supply-bypass capacitance close to the device. Check the ±40 V protection rating against the actual maximum input voltage rather than treating it as a substitute for normal operation within the supply range. This product page combines the Texas Instruments INA114 specifications with package information, practical application guidance, drop-in comparison candidates, and design considerations. The comparisons focus on same-package precision instrumentation amplifiers, while the application guidance focuses on practical gain selection, input protection, noise, and layout considerations for measurement circuits.

RFC Hubungi kami
INA115AU - 1MHz Precision Instrumentation Amplifier | Texas Instruments
INA115AU

INA115AU - 1MHz Precision Instrumentation Amplifier | Texas Instruments

Texas Instruments INA115AU is a precision instrumentation amplifier with 1 MHz gain-bandwidth product, 50 µV maximum offset voltage, 11 nV/√Hz input noise, and 3 mA maximum quiescent current, housed in a 16-pin SOIC package. It is designed for low-level differential measurements where small sensor signals must be amplified accurately while rejecting common-mode interference. An instrumentation amplifier is a specialized amplifier category optimized for measuring a differential voltage superimposed on a larger common-mode voltage. Its internal three-op-amp topology provides high input impedance, accurate differential gain, and strong common-mode rejection. Within the broader hierarchy, an instrumentation amplifier is an analog amplifier, an analog integrated circuit, and ultimately a semiconductor designed for precision signal conditioning. The INA115AU combines switched gain operation, low input offset voltage, low drift, and low input bias current. Its specified maximum input offset voltage is 50 µV, maximum offset drift is 0.25 µV/°C, and maximum input bias current is 2 nA. Common-mode rejection reaches 115 dB minimum, while the device accepts input over-voltage protection up to ±40 V. These characteristics make the amplifier suitable for bridge outputs, current-shunt measurements, and low-level sensor interfaces. The wide supply range extends to ±18 V, with operating use supported from ±2.25 V according to the distributor data. Its 1 MHz bandwidth supports faster measurements than a purely high-resolution, slow instrumentation amplifier, while 11 nV/√Hz input noise preserves low-level signal integrity. A 16-pin SOIC package provides a conventional surface-mount footprint suitable for industrial, instrumentation, and test-equipment designs. Typical applications include precision bridge amplifiers, strain-gauge monitoring, laboratory sensor interfaces, current-shunt amplifiers, and industrial measurement systems. The switched gain function allows one amplifier to serve multiple sensitivity ranges, although the gain-setting network and feedback resistor accuracy must be checked carefully because they directly influence overall measurement accuracy. Designers should verify input common-mode limits, output swing, gain stability, and supply headroom under the intended load. Input protection improves tolerance to accidental over-voltage, but it does not remove the need for correct polarity, common-mode range, and output-swing analysis. Decoupling should follow the manufacturer datasheet guidance, and sensitive analog traces should be kept away from noisy switching paths. This page combines verified manufacturer highlights, distributor availability information, same-package alternative candidates, application guidance, and design cautions that help engineers move from part selection to a board-level implementation without overlooking the distinctions between instrumentation amplifiers.

RFC Hubungi kami
INA115AU-1 - 1 MHz Precision Instrumentation Amplifier | TI
INA115AU-1

INA115AU-1 - 1 MHz Precision Instrumentation Amplifier | TI

Texas Instruments INA115AU-1 is a precision switched-gain instrumentation amplifier with a 1 MHz gain-bandwidth product, 50 uV input offset voltage, 11 nV/√Hz input noise, and 3 mA power consumption. The device is offered in a 16-pin SOIC package and is intended for low-level differential-signal conditioning. An instrumentation amplifier is a specialized analog amplifier that measures the voltage difference between two inputs while rejecting common-mode signals. Its internal three-op-amp architecture provides high input impedance, accurate differential gain, and a defined gain relationship, making it more convenient than a discrete difference amplifier for sensor front ends. Within the broader hierarchy, an instrumentation amplifier is an analog amplifier, a signal-conditioning IC, and part of a measurement and control system. The INA115 family combines precision input offset performance with low input-referred noise and a bandwidth of 1 MHz. Its switched-gain architecture permits gain to be selected through an external resistor connected to the gain-setting pin. The 50 uV offset specification and 11 nV/√Hz noise density are important when resolving millivolt-level or microvolt-level signals, while the 3 mA supply current supports low-power measurement systems. INA115AU-1 operates from dual supplies of ±2.25 V to ±18 V, as identified by Texas Instruments for the INA115AU/1K ordering configuration. The 0.06 V/us slew rate supports accurate settling of larger signal steps. Because the amplifier is designed for differential measurements, input-common-mode range, output swing, and input bias behavior must be checked against the actual signal and supply voltages before the circuit is released for production. Typical uses include bridge-transducer and strain-gauge front ends, precision current measurement, biomedical instrumentation, laboratory measurement equipment, and industrial sensor interfaces. The switched-gain capability simplifies systems in which several gain ranges are required, while the combination of 1 MHz bandwidth, 50 uV offset, and 11 nV/√Hz noise supports accurate signal capture without an unnecessarily high-power amplifier. The principal design consideration is the gain-setting resistor and its associated noise. Use a resistor with suitable low-noise characteristics and keep the gain network close to the gain pin to minimize parasitic capacitance. Input filtering, common-mode rejection, and output settling should be evaluated together because a high-bandwidth amplifier can amplify high-frequency interference as well as the wanted differential signal. This product page combines the exact manufacturer highlights with application guidance, package information, and a practical comparison of documented alternatives. It also highlights the distinction between electrical equivalence and packaging-only ordering codes, helping engineers make a board-level replacement decision without confusing tape-and-reel formats with functional alternatives.

RFC Hubungi kami
INA115AU/1K - 1MHz Precision Instrumentation Amplifier | Texas Instruments
INA115AU/1K

INA115AU/1K - 1MHz Precision Instrumentation Amplifier | Texas Instruments

Texas Instruments INA115AU/1K is a precision, switched-gain instrumentation amplifier with 1 MHz bandwidth, 50 µV maximum input offset voltage, 11 nV/√Hz input noise, and 3 mA power consumption. The device is housed in a 16-pin SOIC (DW) package and is intended for low-level differential signal measurement. An instrumentation amplifier is a specialized amplifier category that combines differential input measurement, high input impedance, accurate gain control, and common-mode rejection. Its place in the signal-chain hierarchy is signal conditioning before an ADC, a sensor interface, or a precision measurement system. The INA115 family extends this hierarchy through switched gain selection, allowing one package to support multiple measurement ranges without changing the external feedback network. The primary features of INA115AU/1K include a 1 MHz gain-bandwidth product, 50 µV maximum offset voltage, 11 nV/√Hz input-referred noise, and 3 mA typical power consumption. The 1 MHz bandwidth supports faster settling than many precision instrumentation amplifiers, while the low offset and noise are important when extracting small sensor signals from larger common-mode voltages. Switched gain makes the device practical for systems that must change sensitivity between measurement ranges. The INA115 uses a precision architecture intended to preserve small differential signals in the presence of common-mode voltage and supply variation. Its 16-pin SOIC package provides a conventional surface-mount footprint suitable for industrial and instrumentation equipment. The manufacturer describes the INA115 as a single-channel, switched-gain-enabled precision instrumentation amplifier, with an operating range extending down to ±2.25 V and up to ±18 V according to comparison records for the family. Typical uses include bridge-sensor signal conditioning, biomedical instrumentation, current-shunt measurement, laboratory test equipment, and precision industrial sensor acquisition. The 1 MHz bandwidth is particularly useful when the measurement must be sampled rapidly, while the 11 nV/√Hz noise specification favors low-amplitude signals such as strain-gauge, thermocouple, and resistive-sensor outputs. Layout should treat the input stage as a high-impedance precision analog circuit. Keep input and feedback traces short, place gain-control components away from sensitive input nets, provide local supply bypassing, and avoid routing high-current or switching signals beneath the amplifier pins. Confirm gain, supply, output-swing, and settling requirements against the manufacturer's recommended operating conditions before committing the layout. This product page combines the manufacturer product information, package and ordering data, verified distributor listings, and cross-reference results with application guidance. It also distinguishes true same-package drop-in options from devices that are only functionally similar, helping engineers compare replacement choices without overlooking footprint, gain, noise, or bandwidth constraints.

RFC Hubungi kami
INA115BU - 1MHz Low-Noise INA | Texas Instruments
INA115BU

INA115BU - 1MHz Low-Noise INA | Texas Instruments

Texas Instruments INA115BU is a precision three-op-amp instrumentation amplifier rated for 1 MHz bandwidth, 50 uV maximum offset voltage, 11 nV/sqrt(Hz) input noise, and 3 mA maximum quiescent current. It is supplied in a 16-pin SOIC package and supports supply voltages from 2.25 V to 18 V, allowing operation from low-voltage analog systems through higher-voltage industrial instrumentation. An instrumentation amplifier is a differential analog signal-conditioning IC that amplifies the voltage between two inputs while rejecting common-mode interference. Its internal hierarchy is instrumentation amplifier, differential amplifier, analog amplifier, and semiconductor. The three-op-amp architecture uses resistive feedback to establish gain, high input impedance, and accurate differential gain control. Exposed input-amplifier connections permit switched-gain networks and alternative feedback arrangements. Key performance features include an offset voltage of 50 uV maximum, input voltage drift of 0.25 uV/degree C maximum, input bias current of 2 nA maximum, and common-mode rejection of 115 dB minimum. The device also provides input over-voltage protection to plus or minus 40 V, making it suitable for measurement interfaces where transient or fault conditions may exceed the normal common-mode range. The INA115BU combines 1 MHz bandwidth with 11 nV/sqrt(Hz) noise density. Its slew rate of 0.6 V/us supports accurate reproduction of moderate-frequency waveforms, while the external gain-setting network allows tradeoffs among gain, bandwidth, and noise. The instrumentation-amplifier topology is particularly useful when a low-level sensor differential must be measured in the presence of a larger common-mode voltage. Typical applications include bridge and strain-gauge signal conditioning, precision current measurement, biomedical instrumentation, industrial process-control sensors, and low-level differential data acquisition. The input-overvoltage protection and high common-mode rejection are useful in industrial environments, while low input bias current supports high-impedance sensor interfaces. Designers should place input and feedback resistors close to the device, maintain symmetric input routing, and verify stability with the intended gain network. Gain-setting resistance must also be checked against the required bandwidth, because the effective gain bandwidth relationship becomes increasingly important as closed-loop gain rises. This product summary combines the manufacturer specifications with practical guidance for gain selection, noise analysis, overvoltage protection, and PCB implementation. It also identifies verified nearby instrumentation amplifiers for engineers evaluating replacement or design-comparison requirements.

RFC Hubungi kami
INA115BUG4 - 1MHz Precision Instrumentation Amplifier | TI
INA115BUG4

INA115BUG4 - 1MHz Precision Instrumentation Amplifier | TI

The Texas Instruments INA115BUG4 is a precision instrumentation amplifier with a 1 MHz gain-bandwidth product, 50 µV input offset voltage, 11 nV/√Hz input noise, and 3 mA power consumption, supplied in a 16-pin SOIC package. It is designed for applications requiring accurate differential measurement from low-level sensors and bridge circuits. An instrumentation amplifier is a specialized amplifier that measures the voltage difference between two inputs while rejecting common-mode signals. Its typical signal-chain hierarchy is instrumentation amplifier → differential amplifier → analog amplifier → analog signal-chain IC. By combining high input impedance, precise gain control, and differential input handling, this device reduces the need for separate input amplifiers in sensor-conditioning systems. Key features include the manufacturer-rated 1 MHz bandwidth, 50 µV input offset voltage, and 11 nV/√Hz noise density. The three-op-amp architecture provides gain adjustment flexibility, while the INA115 additionally exposes connections to the input amplifiers, identified as A1 and A2. Those connections support improved gain accuracy at high gain settings and can assist in implementing switched-gain arrangements. The INA115BUG4 supports single-supply operation from 2.25 V to 18 V according to the INA115BU comparison data. Its instrumentation-amplifier architecture is intended for low-level differential signals, but bandwidth and input-voltage limits must be checked at each selected gain. Because this is an analog precision device, careful grounding, reference configuration, resistor selection, and protection design are essential for repeatable results. Typical applications include bridge-based pressure and load-cell measurements, low-voltage sensor front ends, isolated current sensing, biomedical instrumentation, and industrial process monitoring. The 16-pin SOIC package is also practical for conventional surface-mount assembly, although sensitive input routing must be kept away from switching nodes and high-current paths. For a new design, verify the gain-setting resistor values, allowable input common-mode range, supply voltage, output swing, and input protection limits against the manufacturer datasheet for the intended operating condition. Use a clean analog ground reference and place input and gain-setting components close to the device to minimize parasitic errors. This product summary combines the manufacturer’s device description with practical guidance for INA115 pinout verification, gain selection, sensor conditioning, low-noise layout, package compatibility, and drop-in replacement assessment.

RFC Hubungi kami
INA116PA - 3fA Ultra Low Bias Current In-Amp | TI
INA116PA

INA116PA - 3fA Ultra Low Bias Current In-Amp | TI

The Texas Instruments INA116PA is an ultra-low input bias current instrumentation amplifier delivering 3 fA typical input bias current (25 fA at 85C), a 2 mV maximum input offset voltage, and programmable gain from 1 V/V to 1000 V/V in a 16-pin PDIP (N) package rated from -40C to +85C. An instrumentation amplifier is a specialized precision differential amplifier designed to amplify the difference between two input signals while rejecting common-mode voltage. Within the signal-chain hierarchy, it sits above general-purpose op amps in the amplifier family of analog ICs, combining three internal op-amp stages, precision matched resistors, and FET input technology to achieve performance that discrete designs cannot easily match. The headline feature of the INA116 is its Difet (dielectrically isolated FET) input stage with special guarding techniques that yield the 3 fA typical bias current at 25C. Buffered guard drive pins allow the designer to actively drive cable shields and guard rings, reducing leakage paths that would otherwise dominate performance at femtoampere input levels. Input overvoltage protection adds robustness against transient events at the inputs. The classic three-op-amp topology sets gain from 1 to 1000 V/V with a single external resistor, per the manufacturer datasheet. Minimum common-mode rejection is 86 dB, input noise is 28 nV per root hertz at 1 kHz, and quiescent current is only about 1 mA, permitting operation from +/-4.5 V to +/-18 V supplies (9 V to 36 V total). Typical applications include photodiode and ionization chamber front ends, pH and chemical sensor interfaces, electrometer-grade measurement systems, and precision transducer signal conditioning where source impedance is extremely high. Design consideration: at fA-level bias currents, PCB surface leakage dominates system error, so guard rings driven from the buffered guard outputs and careful board cleaning are essential. This page adds value beyond the manufacturer datasheet by synthesizing distributor pricing, drop-in alternative analysis, comparison tables, and practical design guidance in one place.

RFC Hubungi kami
INA116PAG4 - Ultra-Low Bias Instrumentation Amplifier | TI
INA116PAG4

INA116PAG4 - Ultra-Low Bias Instrumentation Amplifier | TI

The Texas Instruments INA116PAG4 is a precision instrumentation amplifier with extremely low input bias current, a typical value of 3 fA at 25°C, a bandwidth of 800 kHz, and a 16-pin PDIP package. Its gain can be set from 1 to 1000 with one external resistor, while its low input offset voltage supports accurate differential-signal measurement. The device operates from ±4.5 V to ±18 V and is designed for current measurement, sensing, and instrumentation applications. An instrumentation amplifier is a specialized amplifier that measures a small voltage appearing between two inputs while rejecting common-mode voltage, supply noise, and other signals common to both inputs. The INA116PAG4 belongs to the instrumentation-amplifier hierarchy within precision analog signal-chain ICs. Its FET-input architecture and special input-guarding techniques are particularly useful when measuring high-impedance sources whose charging current could otherwise disturb the measurement. The principal features include a 3 fA typical input bias current at 25°C, 25 fA at 85°C, 2 mV maximum input offset voltage, 94 dB common-mode rejection, and a 0.08 V/µs slew rate. Buffered guard-drive pins help reduce leakage through board contamination and PCB insulation paths. The 1-to-1000 gain range makes the device useful across sensor interfaces, precision current shunts, bridge amplifiers, and high-impedance measurement systems. The INA116 uses a three-op-amp instrumentation-amplifier topology, allowing the closed-loop gain to be established with a single gain-setting resistor. Its bandwidth supports accurate static and moderate-frequency measurements, but the usable bandwidth decreases as gain increases according to the gain-bandwidth relationship. Buffered inputs, a low-noise internal design, and the available guard outputs help preserve signal integrity in high-impedance layouts. Typical uses include photodiode and electrochemical sensor interfaces, precision shunt amplifiers, laboratory instrumentation, and industrial current sensing. The 16-pin PDIP package also supports through-hole assembly and prototyping systems. Because input bias current and leakage dominate many high-impedance designs, the physical implementation around the input and guard pins is as important as the nominal amplifier specifications. For reliable operation, keep input and gain-resistor connections short, provide the supply and bypass-capacitor arrangement specified by the manufacturer, and route guard outputs as shown in the datasheet. Confirm the maximum input voltage, common-mode range, output swing, and operating-temperature limits for the actual board revision before connecting external sources. This page combines device specifications, lifecycle information, drop-in alternatives, comparison data, and practical high-impedance layout guidance. It is intended to help engineers evaluate the INA116PAG4 quickly while preserving the leakage, guarding, gain, and supply considerations that determine real measurement performance.

RFC Hubungi kami
INA116UA - 3fA Ultra-Low Bias In-Amp SOIC-16 | Texas Instruments
INA116UA

INA116UA - 3fA Ultra-Low Bias In-Amp SOIC-16 | Texas Instruments

The Texas Instruments INA116UA is an ultra-low input bias current instrumentation amplifier with 3 fA typical input bias current at 25C, 28 nV/Hz input noise at 1 kHz, and a 800 kHz bandwidth, housed in a 16-pin SOIC package (7.50 mm width). An instrumentation amplifier is a specialized differential amplifier designed to amplify the difference between two input signals while rejecting common-mode voltage. Within the signal-chain hierarchy, it sits above general-purpose op amps: an instrumentation amplifier (in-amp) is a precision differential amplifier -> amplifier IC -> analog signal conditioning IC. Unlike a standard op amp, an in-amp provides fixed or resistor-set gain without precision external resistor matching, making it the preferred front end for sensor bridges and transducer outputs. Key features of the INA116UA include Difet (dielectrically isolated FET) inputs achieving 3 fA bias at 25C and only 25 fA at 85C, buffered guard drive pins adjacent to both inputs that boot-strap cable and PCB leakage currents, a low 2 mV maximum input offset voltage, and a low 1 mA quiescent current. Its classic three-op-amp topology allows gain to be set from 1 V/V to 1000 V/V with a single external resistor. Technically, the guarded Difet input structure is what enables femtoampere-class bias currents: guard pins driven at the input common-mode potential intercept surface leakage paths on the PCB, so high-impedance sources such as pH electrodes, photodiodes, and ion chambers can be measured without input-current-induced errors. The 800 kHz bandwidth supports dynamic measurements at moderate gains. Typical applications include pH and ion-selective electrode front ends, photodiode and photomultiplier current monitoring, capacitive and piezoelectric sensor amplification, and precision laboratory electrometer circuits. Design consideration: the guard pins must be actively driven (bootstrapped) for the 3 fA specification to be realized on a practical PCB; without guarding, board leakage will dominate input current by orders of magnitude. This page synthesizes distributor pricing, packaging data, and practical guarding design notes not found in the manufacturer datasheet, with pricing as of 2026-09-13.

RFC Hubungi kami
INA116UAG4 - 3 fA Input Bias Instrumentation Amplifier | Texas Instruments
INA116UAG4

INA116UAG4 - 3 fA Input Bias Instrumentation Amplifier | Texas Instruments

Texas Instruments INA116UAG4 is an ultra-low-input-bias-current instrumentation amplifier with a typical input bias current of 3 fA at 25°C and 25 fA at 85°C, a gain range of 1 to 1000, and a 16-pin SOIC package. The device also provides an 800 kHz -3 dB bandwidth and a 0.8 V/µs slew rate. An instrumentation amplifier is a precision analog signal-conditioning IC that amplifies the voltage difference between two inputs while rejecting common-mode signals. It belongs to the amplifier hierarchy as an instrumentation amplifier, a differential amplifier, and ultimately an analog integrated circuit. The INA116 uses a three-op-amp topology and differential inputs protected by special guarding techniques, making it suitable for high-impedance sensors where even picoamp-level input current could create unacceptable measurement error. The primary features of the INA116UAG4 include extremely low input bias current, gains from 1 to 1000 established with one external resistor, and a bandwidth of 800 kHz. Its 0.8 V/µs slew rate supports accurate reproduction of moderate-frequency signals. The guarded input structure reduces leakage through PCB contamination and helps preserve accuracy in high-impedance measurement circuits. Technically, the monolithic FET-input architecture separates the input stage from the gain-setting network and allows operation with extremely low input currents. Differential inputs reduce sensitivity to common-mode voltage, while the internal three-op-amp topology provides accurate gain control without requiring matched external resistors. This combination is especially useful when source impedance is high and the sensor output is much smaller than environmental offsets or interference. Typical uses include precision current measurement, pH and electrochemical sensor interfaces, photodiode signal chains, biomedical instrumentation, and low-current sensor amplification. The 800 kHz bandwidth is suitable for sensor systems requiring signal amplification without the complexity of a high-speed voltage-feedback amplifier. The 16-pin SOIC package allows conventional surface-mount assembly and PCB routing. The primary design consideration is guarding and board cleanliness. Keep input traces short, isolate them from high-impedance leakage paths, remove contamination, and place the gain resistor close to the gain-setting pins. Confirm the actual input bias current, common-mode range, supply limits, output swing, and operating temperature limits against the manufacturer datasheet before finalizing a production design. This page combines manufacturer specifications, ordering information, drop-in family options, application guidance, and design cautions for engineers evaluating the INA116UAG4 as a low-bias precision analog front end.

RFC Hubungi kami
INA117AM - ±200V Difference Amplifier | Texas Instruments
INA117AM

INA117AM - ±200V Difference Amplifier | Texas Instruments

Texas Instruments INA117AM is a precision unity-gain difference amplifier with a common-mode input range up to ±200 V, a 200 kHz bandwidth, and an 8-pin TO-99 metal-can package. It is designed to extract small differential voltages from high-voltage or high-impedance signal chains without requiring an external precision resistor network. A difference amplifier is a specialized amplifier topology that amplifies the voltage between two inputs while rejecting a voltage common to both inputs. The INA117 belongs to the broader hierarchy of differential amplifiers, instrumentation signal conditioners, amplifier ICs, and analog semiconductor devices. Its integrated thin-film resistor network provides matched ratios, allowing accurate differential measurement when its common-mode and output operating limits are respected. The monolithic INA117 combines a precision operational amplifier with an integrated resistor network. Its unity-gain architecture makes it suitable for direct differential sensing, while the ±200 V common-mode capability separates the usable input signal from the potentially much larger voltage appearing at both inputs. The 200 kHz bandwidth supports measurements beyond static DC conditions but remains focused on precision signal extraction rather than high-speed data conversion. The INA117 family is also specified for operation from -40°C to 85°C. Two package options are available for the INA117 family: an 8-pin plastic mini-DIP and an 8-pin SO-8 surface-mount package. The INA117AM is the TO-99-8 metal-can ordering option shown by the manufacturer and distributor listings. The metal-can format supports compact through-hole insertion and is useful where a robust, shielded package is preferred over a surface-mount carrier. Its 8-pin configuration also means the differential amplifier requires careful signal routing and grounding around the circular package. Typical applications include high-voltage current sensing, power-converter feedback monitoring, battery-system measurement, industrial transducer interfaces, and instrumentation where a small differential signal is superimposed on a large common-mode voltage. In these systems, the INA117 can reject the common signal and present a scaled differential result to an ADC, comparator, control loop, or measurement instrument. Input protection, common-mode transient limits, output saturation, and thermal behavior must be evaluated together. When implementing this device, verify that neither input exceeds the specified common-mode range under every operating condition. Keep sensitive input and reference connections short, use a stable low-noise supply, and provide adequate return paths for high-impedance sources. Account for output settling and bandwidth when filtering small signals from fast common-mode transients, since common-mode rejection and transient performance are distinct design considerations. This product page combines the manufacturer’s device description, package information, operating-temperature range, exact ordering identifier, source documents, application guidance, and qualified replacement analysis. It also distinguishes genuine pin-compatible alternatives from devices that share only the broad function of high-voltage difference amplification, helping engineers make a PCB-level replacement decision rather than a feature-level comparison.

RFC Hubungi kami
INA117BM - Precision Difference Amplifier | Texas Instruments
INA117BM

INA117BM - Precision Difference Amplifier | Texas Instruments

The Texas Instruments INA117BM is a precision unity-gain difference amplifier with a very high common-mode input voltage range, integrated thin-film resistor network, and low nonlinearity of 0.001%. The device is specified for a 200 kHz bandwidth in the CSO: SHE implementation, with a 500 kHz option also described for the CSO: TID implementation. INA117BM is packaged in the 8-pin TO-99-8 metal package, making it suitable for instrumentation, buffer, and high-side current-sense applications where the signal can be close to the supply rails. The amplifier is designed to reject common-mode interference while preserving the differential signal, which helps improve measurement accuracy in systems exposed to large common-mode voltages. A difference amplifier is an analog signal-conditioning component that subtracts one input voltage from another and amplifies the resulting difference. The INA117 belongs to the instrumentation amplifier and differential amplifier family, where precision resistor matching helps maintain accurate gain and common-mode rejection. Its monolithic construction combines a precision operational amplifier with an integrated thin-film resistor network, simplifying circuit design compared with a discrete resistor network and separate op amp. The result is a fixed unity-gain device intended for applications requiring accurate differential measurement rather than adjustable gain. Key characteristics of the INA117BM include low nonlinearity of 0.001% and a 200 kHz bandwidth for the specified CSO: SHE die. The wide common-mode input range allows the input terminals to operate near the supply-voltage envelope, which is useful when measuring small differential signals riding on a larger voltage. The device is offered in an 8-pin plastic mini-DIP and an 8-pin SO-8 surface-mount package in the INA117 family; INA117BM specifically uses the TO-99-8 package. The specified operating temperature range for the family is -40°C to 85°C. Typical uses include high-side current sensing in motor-control and power-conversion systems, battery monitoring, precision bridge amplifiers, and industrial measurement front ends. The unity-gain architecture makes the part appropriate when the system requires a fixed differential gain of one and very high common-mode rejection. Applications should still verify the exact supply, common-mode, output-swing, and stability limits for the selected package and operating conditions before production release. For PCB implementation in a through-hole TO-99-8 design, preserve adequate clearance around the metal package, route sensitive input traces away from switching nodes, and use a stable reference or low-impedance return for the signal source. Because the internal gain network is precision matched, careful grounding and connector placement are important for preserving the benefit of the common-mode rejection. This page provides technical guidance, application fit, and pin-compatible replacement information for engineers evaluating the INA117BM.

RFC Hubungi kami
INA117KU - ±200V High CMV Difference Amplifier | TI
INA117KU

INA117KU - ±200V High CMV Difference Amplifier | TI

The Texas Instruments INA117KU is a precision unity-gain difference amplifier with a very high common-mode input voltage range of up to ±200V (VS = ±15V), housed in an 8-pin SOIC (SO-8) surface-mount package. It delivers a gain error of just 0.02% max and nonlinearity of 0.001% max. A difference amplifier is a special class of instrumentation amplifier that subtracts two input signals and rejects any voltage common to both inputs. Within the signal-chain hierarchy (difference amplifier -> instrumentation amplifier -> operational amplifier -> analog front end), the INA117 occupies a niche defined by extreme common-mode tolerance, allowing it to measure small differential signals riding on large DC or AC common-mode voltages. Key features include a ±200V common-mode input range, protected inputs rated to ±500V common-mode and ±500V differential, unity gain with 0.02% max gain error, 0.001% max nonlinearity, and a minimum CMRR of 86 dB. These numbers stem from an integrated thin-film resistor network that is precisely matched on-chip, eliminating external precision resistor matching. Architecturally, the monolithic IC combines a precision bipolar op amp with the laser-trimmed resistor network. Because the resistor ratios are trimmed on the same die, the INA117 achieves CMRR and accuracy unobtainable with discrete resistor-divided op amp circuits, and its CMRR holds up over temperature. Typical applications include current shunt measurements on high-side bus rails, industrial motor drive voltage sensing, level shifting of high-voltage signals down to ADC-compatible ranges, and test equipment input conditioning. Design-wise, note that the ±200V range requires VS of ±15V; lower supplies reduce the usable common-mode window. Reference pins should be driven from a low-impedance source to preserve CMRR. This page synthesizes distributor pricing, drop-in alternatives, comparison tables, and practical design notes not found in the manufacturer datasheet.

RFC Hubungi kami
INA117KU/2K5 - High Common-Mode Voltage Difference Amplifier | TI
INA117KU/2K5

INA117KU/2K5 - High Common-Mode Voltage Difference Amplifier | TI

The Texas Instruments INA117KU/2K5 is a precision unity-gain difference amplifier with a very high common-mode input voltage range of plus/minus 200V at VS = plus/minus 15V, delivered in an 8-pin SOIC (SO-8) surface-mount package rated from -40C to +85C. It integrates a precision monolithic op amp with a laser-trimmed thin-film resistor network, allowing accurate measurement of small differential voltages in the presence of very large common-mode signals without a discrete resistor divider front end. A difference amplifier (also called a differential amplifier or difference-amplifier IC) is a specialized analog signal-conditioning device that amplifies the voltage difference between two inputs while rejecting voltages common to both. Within the amplifier hierarchy, it sits under operational amplifiers and instrumentation amplifiers, which in turn belong to the broader class of linear amplifier ICs used in analog front ends and power management chains. Key features include common-mode input protection to plus/minus 500V (both common-mode and differential), a maximum gain error of 0.02% in unity gain, maximum nonlinearity of 0.001%, and a minimum CMRR of 86dB. The KU (SO-8) version provides a 200kHz bandwidth, per the specification note in the TI INA117 datasheet covering the CSO SHE versus TID process options. Technically, the INA117 uses an integrated precision resistor network around an internal op amp so the external circuit sees a true unity-gain subtractor. Laser trimming of the thin-film resistors sets the CMRR and gain accuracy without external calibration, and the wide protected input structure withstands faults up to plus/minus 500V. Typical applications include DC bus and motor-drive voltage sensing, battery pack monitoring, industrial process-control transducer interfaces, and data-acquisition systems that must reject high ground potential differences. The /2K5 suffix denotes the 2,500-piece tape-and-reel packing option. A key design consideration: the input pins must be series-limited per the datasheet fault-protection guidance so the plus/minus 500V protection rating holds under sustained overvoltage. This page synthesizes distributor pricing, drop-in alternative data, and practical design notes not found in the manufacturer datasheet alone.

RFC Hubungi kami
INA117P - ±200V High Common-Mode Difference Amplifier | TI
INA117P

INA117P - ±200V High Common-Mode Difference Amplifier | TI

The Texas Instruments INA117P is a precision unity-gain difference amplifier with a very high common-mode input voltage range of up to ±200V, housed in an 8-pin plastic DIP (PDIP-8) package. It delivers 0.001% maximum nonlinearity, a 200kHz bandwidth, and operation over the -40°C to +85°C industrial temperature range. A difference amplifier is a specialized analog signal-processing IC that measures the voltage difference between two nodes while rejecting any voltage common to both. Within the signal-chain hierarchy, it sits between a general-purpose operational amplifier and a full instrumentation amplifier: it provides a fixed, laser-trimmed gain and superior common-mode rejection, but no adjustable gain. Difference amplifiers are essential wherever a small sensor signal rides on a large common-mode offset, such as current shunt monitoring on high-voltage buses or motor-drive phase sensing. The INA117P integrates a precision op amp with a matched thin-film resistor network on a single monolithic die. This integration is the key differentiator: resistor matching and thermal tracking on-chip yield a common-mode rejection and gain accuracy that discrete resistor-op-amp solutions cannot achieve over temperature. The ±200V common-mode range far exceeds what a conventional op amp front end can tolerate, allowing direct connection across high-voltage rails without a divider or isolator. Typical applications include high-side and low-side current sensing in industrial drives, DC bus voltage monitoring in motor controllers and inverters, battery-management voltage taps, and data-acquisition front ends that must reject large ground offsets. In design, note that the device requires dual supplies (typically ±15V) and that the ±200V common-mode limit applies while powered; beyond the limit, protection must be external. Output is a ground-referenced signal equal to the input differential. This page synthesizes distributor pricing context, verified drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFC Hubungi kami
INA117P-BI - ±200V Common-Mode Differential Amplifier | TI
INA117P-BI

INA117P-BI - ±200V Common-Mode Differential Amplifier | TI

The Texas Instruments INA117P-BI is a precision unity-gain difference amplifier with a very high common-mode input voltage range of ±200V, designed to measure small differential voltages in the presence of large common-mode signals. The device uses a precision operational amplifier with an integrated thin-film resistor network, providing a compact solution for high-voltage instrumentation, current sensing, and industrial measurement systems. It is packaged in an 8-pin plastic mini-DIP package. A difference amplifier is a voltage-feedback amplifier that amplifies the voltage difference between two input terminals while rejecting voltage common to both inputs. The INA117P-BI is intended for applications where the signal of interest is small but the surrounding common-mode voltage can be large. Its ±200V common-mode input range is particularly useful when measuring small voltages across high-voltage bus systems, power-conversion circuits, and industrial equipment. Key performance specifications include a maximum unity-gain error of 0.02%, a maximum nonlinearity of 0.001%, a minimum CMRR of 86dB, and protected inputs rated at ±500V common-mode and ±500V differential. The device operates from a single supply or dual supply arrangement described by the manufacturer datasheet, and its specified operating temperature range is -40°C to +85°C. The INA117 family is also available in an 8-pin SO-8 surface-mount package for compact designs. The INA117P-BI is suitable for precision measurement, power-supply monitoring, current-shunt instrumentation, and analog signal-conditioning systems. Its integrated thin-film network improves gain matching and common-mode rejection without requiring external matched resistors. Designers should still provide input protection appropriate to the application, maintain the specified supply limits, and account for input bias-current effects and thermal conditions at the measurement nodes. For PCB implementation, place the amplifier close to the sensing components and route high-voltage and sensitive-signal paths to minimize leakage, contamination, and coupling. Use guarded grounding and clean analog return paths when measuring microvolt-level signals. The 8-pin PDIP format supports through-hole prototyping and repair, while the SO-8 alternative is preferable where board area is constrained. This page combines the manufacturer specifications, package details, sourcing information, and design guidance needed to evaluate the INA117P-BI for high-common-mode measurement systems.

RFC Hubungi kami
INA117PG4 - 200kHz High-CMV Difference Amp | Texas Instruments
INA117PG4

INA117PG4 - 200kHz High-CMV Difference Amp | Texas Instruments

Texas Instruments INA117PG4 is a single-amplifier precision difference amplifier with a 200 kHz bandwidth, 2.6 V/us slew rate, and a very high common-mode input voltage range. It accepts dual supplies of ±5 V to ±18 V and is packaged in an 8-pin through-hole plastic DIP. The device is intended for measuring small differential voltages in the presence of larger common-mode signals. A difference amplifier is a specialized operational-amplifier circuit that subtracts two input voltages and rejects their common component. This product type belongs to the hierarchy of difference amplifier, instrumentation amplifier, operational amplifier, and analog signal-conditioning IC. It is useful when a sensor or measurement node produces a small differential signal over a larger voltage reference or operating range. Key characteristics include an input offset voltage of 1 mV, 70 dB instrumentation-amplifier performance, 200 kHz bandwidth, and a 2.6 V/us slew rate. Its ±5 V to ±18 V supply range supports positive, negative, and split-supply operation. The single-amplifier configuration integrates the precision operational amplifier and resistive network needed for unity-gain differential measurement. The INA117PG4 uses a monolithic integrated circuit containing a precision op amp and thin-film resistor network. Its architecture supports accurate measurement of small differential voltages while suppressing common-mode voltage. The listed 20 mA per channel and 70 dB performance describe the device as an instrumentation-oriented difference amplifier rather than a general-purpose unity-gain buffer. Typical uses include high-side current measurement, bridge-sensor signal conditioning, battery monitoring, instrumentation inputs, and precision differential-to-single-ended conversion. Its broad common-mode range is especially useful when the measured difference is small relative to the voltage common to both input terminals. The 200 kHz bandwidth also makes it suitable for applications that need more signal bandwidth than a slow precision-only amplifier. Design the circuit so the common-mode voltage and differential input remain within the device's operating limits. Use a stable, low-noise reference when a nonzero differential threshold is required, and provide adequate bypassing around the supply pins. Because it is an 8-pin through-hole package, the INA117PG4 is convenient for prototyping, educational instruments, and industrial control boards with conventional DIP mounting. This product record combines the manufacturer's device classification with package, electrical, environmental, and application details, while adding comparison guidance and engineering design notes for faster component selection.

RFC Hubungi kami
INA117SM - High Common-Mode Difference Amplifier | TI
INA117SM

INA117SM - High Common-Mode Difference Amplifier | TI

The Texas Instruments INA117SM is a precision unity-gain difference amplifier in an 8-pin TO-99-8 package. It is designed to measure small differential voltages in the presence of large common-mode voltages. The device combines a precision operational amplifier with an integrated thin-film resistor network, providing 0.001% low nonlinearity and a bandwidth of 200 kHz when manufactured in the CSO: SHE process. A difference amplifier is a specialized amplifier configuration that rejects voltage common to both inputs and amplifies the voltage difference between them. The INA117 belongs to the high-common-mode difference-amplifier category, where its common-mode rejection capability is more important than its ability to operate only within a conventional low-voltage signal range. It is used as a signal-conditioning stage between high-voltage sensing nodes and downstream measurement or control circuitry. The principal benefits of the INA117SM are its very high common-mode input range, low nonlinearity of 0.001%, and 200 kHz bandwidth in the CSO: SHE version. Its unity-gain architecture simplifies closed-loop implementation while the integrated resistor network reduces external component count. The TO-99-8 package also provides a traditional through-hole format for instrumentation and industrial equipment where long-term availability and straightforward assembly are important. Internally, the INA117SM consists of a monolithic precision amplifier and thin-film resistor network. The difference-amplifier topology subtracts the two input voltages and multiplies the resulting differential signal by the closed-loop gain. At unity gain, the input pair is configured so that common-mode voltage is rejected while the desired sensor differential is amplified. Its specified bandwidth supports measurement systems that need more signal bandwidth than a slow precision-only amplifier, although filtering may still be required for high-noise environments. Typical applications include high-voltage current sensing, bridge-sensor signal conditioning, battery and power-system monitoring, industrial process measurement, and laboratory instrumentation. The device is particularly useful when a low-level differential signal is superimposed on a much larger common-mode voltage. System designers should also consider input protection, supply requirements, resistor tolerance, and the bandwidth required for the sensed waveform when assigning the amplifier. The main design consideration is that the INA117SM does not eliminate the need for careful analog layout. Keep input and feedback traces short, place compensation or filtering components close to the device, and avoid routing high-current paths near the sensitive input nodes. Confirm the common-mode and supply limits against the exact datasheet ordering information before applying the part where the input voltage can approach a system rail. This page consolidates the verified INA117SM product information, source links, technical distinctions, and selection guidance into one engineering reference. It also identifies same-package family options and explains where application-specific verification remains necessary, helping designers choose a replacement without assuming that different INA117 order codes are automatically interchangeable.

RFC Hubungi kami
INA117SMQ - High Common-Mode Differential Amplifier | Texas Instruments
INA117SMQ

INA117SMQ - High Common-Mode Differential Amplifier | Texas Instruments

The Texas Instruments INA117SMQ is a precision unity-gain difference amplifier with a common-mode input voltage range of ±200 V, 200 kHz bandwidth, and an 8-pin TO-99 metal-can package. It combines a precision operational amplifier with an integrated thin-film resistor network to measure small differential voltages while rejecting large common-mode signals. The device operates from single or dual supplies and is specified over a -40°C to +85°C temperature range. A difference amplifier is a specialized analog signal-conditioning IC that subtracts two input voltages and amplifies the difference by a fixed gain. In the precision unity-gain configuration used by the INA117 family, the common-mode signal is rejected by the matched resistor network rather than being amplified. This places the INA117 hierarchy within precision difference amplifiers, instrumentation signal-conditioning circuits, analog amplifiers, and the broader semiconductor category. Key features include a ±200 V common-mode input range, unity differential gain, and a 200 kHz bandwidth. The high common-mode capability allows the amplifier to operate on battery, industrial, automotive, or power-system voltages without requiring the inputs to remain close to ground. The monolithic thin-film network also provides stable matching between the input resistors, which improves common-mode rejection and repeatability compared with discrete resistor networks. Technically, the INA117 is designed for accurate differential measurement rather than high-speed signal processing. Its 200 kHz bandwidth supports measurements in power-conversion, motor-control, battery-monitoring, and industrial-control systems, but it is not intended for video-frequency amplification. Input protection is especially important because the common-mode rating describes the intended signal range and does not replace correct supply, absolute-maximum, and transient-voltage analysis. Typical applications include high-side current sensing, power-supply current monitoring, battery-pack measurement, motor-control feedback, and high-voltage instrumentation. Designers commonly place the device between a sensing resistor and an analog-to-digital converter so that a small differential voltage can be measured while a much larger common-mode voltage is rejected. The primary design consideration is protecting the input stage from transients and exceeding the device's absolute-maximum ratings. Keep input routing short, use suitable input attenuation or clamping networks, and reference the output carefully for single-supply operation. Stable operation also depends on maintaining the specified supply voltage and avoiding excessive input impedance asymmetry at the two inputs. This product page combines the INA117 family specifications with practical guidance on high-common-mode sensing, package considerations, input protection, and qualified drop-in alternatives. It is intended to help engineers identify whether the TO-99 packaged INA117SMQ fits a high-voltage measurement design and what parameters must be checked before substitution.

RFC Hubungi kami