Texas Instruments

INA116UAG4 - 3 fA Input Bias Instrumentation Amplifier | Texas Instruments

MPN: INA116UAG4 ✗ Akhir Hayat
3 fA typical Id 16-pin SOIC Package
MOQ: 1 |

INA116UAG4 Ringkasan

Texas Instruments INA116UAG4 is an ultra-low-input-bias-current instrumentation amplifier with a typical input bias current of 3 fA at 25°C and 25 fA at 85°C, a gain range of 1 to 1000, and a 16-pin SOIC package. The device also provides an 800 kHz -3 dB bandwidth and a 0.8 V/µs slew rate.

An instrumentation amplifier is a precision analog signal-conditioning IC that amplifies the voltage difference between two inputs while rejecting common-mode signals. It belongs to the amplifier hierarchy as an instrumentation amplifier, a differential amplifier, and ultimately an analog integrated circuit. The INA116 uses a three-op-amp topology and differential inputs protected by special guarding techniques, making it suitable for high-impedance sensors where even picoamp-level input current could create unacceptable measurement error.

The primary features of the INA116UAG4 include extremely low input bias current, gains from 1 to 1000 established with one external resistor, and a bandwidth of 800 kHz. Its 0.8 V/µs slew rate supports accurate reproduction of moderate-frequency signals. The guarded input structure reduces leakage through PCB contamination and helps preserve accuracy in high-impedance measurement circuits.

Technically, the monolithic FET-input architecture separates the input stage from the gain-setting network and allows operation with extremely low input currents. Differential inputs reduce sensitivity to common-mode voltage, while the internal three-op-amp topology provides accurate gain control without requiring matched external resistors. This combination is especially useful when source impedance is high and the sensor output is much smaller than environmental offsets or interference.

Typical uses include precision current measurement, pH and electrochemical sensor interfaces, photodiode signal chains, biomedical instrumentation, and low-current sensor amplification. The 800 kHz bandwidth is suitable for sensor systems requiring signal amplification without the complexity of a high-speed voltage-feedback amplifier. The 16-pin SOIC package allows conventional surface-mount assembly and PCB routing.

The primary design consideration is guarding and board cleanliness. Keep input traces short, isolate them from high-impedance leakage paths, remove contamination, and place the gain resistor close to the gain-setting pins. Confirm the actual input bias current, common-mode range, supply limits, output swing, and operating temperature limits against the manufacturer datasheet before finalizing a production design.

This page combines manufacturer specifications, ordering information, drop-in family options, application guidance, and design cautions for engineers evaluating the INA116UAG4 as a low-bias precision analog front end.

Pilihan pengganti yang segera untuk INA116UAG4 — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

Varietas dalam siri ini

Model serupa yang kompatibel dengan pengganti yang segera INA116UAG4 (sama faktor bentuk dan kaki) — berbeza dalam Amplifier Type, Gain Range, Package, Bandwidth, Input Offset Voltage.

Texas Instruments
Amplifier Type: Precision instrumentation amplifier
Gain Range: 1 to 10,000
Input Offset Voltage: 50 uV
Bandingkan Dengan INA116UAG4 →
Texas Instruments
Amplifier Type: Instrumentation Amplifier
Gain Range: 1 V/V to 1000 V/V (single external resistor)
Package: 16-SOIC (0.295 in, 7.50 mm width)
Bandingkan Dengan INA116UAG4 →

INA116UA

✅ Masuk Drop-In
Texas Instruments
📦 16-pin SOIC (UA)
Instrumentation Amplifier · 1 · 3 fA typ at 25C · 25 fA · 2 mV max · 1 V/V to 1000 V/V (single external resistor) · 800 kHz · 28 nV/sqrt(Hz) at 1 kHz

Hubungi untuk harga

Lihat Datasheet →

INA116UA

✅ Masuk Drop-In
Texas Instruments
📦 16-pin SOIC (UA)
Instrumentation Amplifier · 1 · 3 fA typ at 25C · 25 fA · 2 mV max · 1 V/V to 1000 V/V (single external resistor) · 800 kHz · 28 nV/sqrt(Hz) at 1 kHz

Hubungi untuk harga

Lihat Datasheet →

INA116UAG4 Penilaian maksimum & Ciri-ciri Elektrik

Product Type Ultra-low-input-bias-current instrumentation amplifier
Input Bias Current at 25°C 3 fA typical
Input Bias Current at 85°C 25 fA typical
Gain Range 1 to 1000
Gain Setting Method 1 external resistor
Internal Topology 3-op-amp instrumentation amplifier
Input Stage Monolithic FET input
Bandwidth 800 kHz -3 dB
Slew Rate 0.8 V/µs
Number of Circuits 1 circuit
Differential Input Yes
Input Guarding Special input guarding techniques
Kemasan 16-pin SOIC
Package Code UA
Jenis Pemasangan Surface mount
Temperature Grade Industrial
Amplifier Type Standard general-purpose instrumentation amplifier

Panduan Konfigurasi Pin INA116UAG4 ua

Konfigurasi pin untuk INA116UAG4 (ua pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.

Garis bentuk pengecah pakai ua untuk INA116UAG4

Tiada data garisan pin yang diperoleh untuk INA116UAG4.

Rujuk kepada lembaran data untuk konfigurasi pin penuh.

Aplikasi Biasa

INA116UAG4 patut untuk 6 aplikasis: Electrochemical Sensor Interface, Photodiode Signal Acquisition, Precision Current Measurement, Medical and Biomedical Instrumentation, Industrial Sensor Conditioning, Precision Bridge Measurement.

🧩

Electrochemical Sensor Interface

The INA116UAG4 fits electrochemical and pH-style sensors because its input bias current is only 3 fA at 25°C and 25 fA at 85°C. A high-impedance sensor can present source resistance in the gigohm range, where amplifier input current produces meaningful voltage error even when the sensor voltage is only millivolts. The differential three-op-amp architecture also helps reject common-mode voltage present on both sensor electrodes. Place the device close to the sensor connector, keep input traces short, and apply guarding according to the manufacturer datasheet. Its resistor-programmed gain from 1 to 1000 allows weak sensor outputs to be amplified close to the source, improving signal integrity before downstream filtering and digitization.

📷

Photodiode Signal Acquisition

The INA116UAG4 is appropriate for photodiode and optical-detector front ends where source leakage and amplifier bias current establish the noise floor. Its 3 fA typical input bias current at 25°C minimizes the voltage generated across very high photodiode or transimpedance-network resistance. The 800 kHz -3 dB bandwidth and 0.8 V/µs slew rate provide useful response beyond slow photodiode systems while preserving the low-input-current architecture. Keep the photodiode input route compact and away from switching circuitry, and evaluate the gain resistor and compensation network in the application circuit rather than increasing gain indiscriminately.

⚡

Precision Current Measurement

The INA116UAG4 can amplify the output of a low-current transducer where the measurement target approaches the picoamp range. Its 3 fA typical input bias current at 25°C prevents the amplifier from loading the sensing element, while differential input helps reject supply and ground disturbances common to both sides of the sensor. The programmable gain range of 1 to 1000 allows the signal chain to use the full ADC range without excessive post-amplification noise. For a complete measurement system, account for transducer sensitivity, burden resistance, offset, and bandwidth when choosing the external gain resistor and subsequent filter.

💊

Medical and Biomedical Instrumentation

The INA116UAG4 supports low-level biomedical instrumentation because its extremely low input bias current reduces loading on skin-electrode, bioimpedance, and ion-sensor interfaces. The 3 fA typical input current at 25°C is especially relevant when electrode impedance is high and patient signals are small. Differential input helps reject common-mode interference, and the gain range of 1 to 1000 provides flexibility for signal levels ranging from millivolts to sub-volt instrumentation signals. Medical designs still require separate consideration of patient protection, isolation, leakage current, electromagnetic immunity, and application-specific qualification; those safety functions are not established by the amplifier specifications alone.

🏭

Industrial Sensor Conditioning

The INA116UAG4 can condition outputs from high-impedance industrial sensors when leakage current is a meaningful error source. Its 3 fA typical input bias current at 25°C reduces interaction with long sensor cables and high-impedance transducers, while the differential topology supports common-mode rejection in industrial environments. The 800 kHz bandwidth is suitable for many process and condition-monitoring signals, and the 0.8 V/µs slew rate avoids excessive delay on moderate transients. PCB cleanliness, guard routing, isolation from high-voltage switching nodes, and suitable surge protection remain critical because environmental contamination and coupling paths can dominate errors below the amplifier's intrinsic input-current level.

⚙️

Precision Bridge Measurement

The INA116UAG4 is useful in bridge-based pressure, strain, and resistance measurements when the bridge output is small and the complete circuit is referenced near ground. The three-op-amp differential architecture is intended to amplify a small voltage between bridge nodes while rejecting common-mode excitation and ground differences. Its 3 fA typical input bias current at 25°C minimizes errors in high-impedance branches, and the gain range of 1 to 1000 supports excitation levels that vary across sensors. Use the manufacturer application guidance to select the gain resistor and output filter, and verify bridge excitation, input common-mode range, and output swing against the final sensor and mechanical tolerances.

What is the input bias current of the INA116UAG4?
The INA116UAG4 has a typical input bias current of 3 fA at 25°C and 25 fA at 85°C. These extremely low values allow the amplifier to measure signals from very high-impedance sources without the source resistance creating excessive offset. According to the Texas Instruments INA116 datasheet, the low bias current results from a monolithic FET-input design and special input-guarding techniques.
What is the gain range of the INA116UAG4?
The INA116UAG4 supports gains from 1 to 1000 using a single external gain-setting resistor. Its three-op-amp topology allows the gain to be established with one resistor rather than a matched resistor network. According to the Texas Instruments INA116 datasheet, this combination of wide gain range and extremely low input bias current makes the device useful for precision sensor and low-current measurement systems.
What is the bandwidth and slew rate of the INA116UAG4?
The INA116UAG4 has an 800 kHz -3 dB bandwidth and a slew rate of 0.8 V/µs. These figures place it between precision DC amplifiers and much faster signal-chain amplifiers. According to the Texas Instruments INA116 datasheet and product documentation, the device is intended for high-impedance instrumentation where low input current is more important than the bandwidth of a general-purpose precision op amp.
Where can I download the INA116UAG4 datasheet PDF?
The official INA116UAG4 datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/ina116.pdf. The document contains the device pin configuration, electrical characteristics, gain-setting information, input-guarding guidance, and application details. Use the manufacturer PDF for final design decisions and board-level implementation.
Where is the INA116UAG4 pinout located?
The INA116UAG4 pinout and pin descriptions are located in the pin-configuration section of the Texas Instruments INA116 datasheet at https://www.ti.com/lit/ds/symlink/ina116.pdf. The component is packaged in a 16-pin SOIC. Use the manufacturer pin table when assigning input, output, supply, gain-resistor, and guard connections.
Is the INA116UAG4 suitable for high-impedance sensor measurement?
The INA116UAG4 is specifically suited to high-impedance sensor measurement because its input bias current is only 3 fA at 25°C and 25 fA at 85°C. According to the Texas Instruments INA116 datasheet, this reduces errors introduced when sensor source resistance and PCB leakage interact with amplifier input current. It is appropriate for electrochemical, photodiode, and other very-high-impedance sources.
What is the best drop-in replacement for the INA116UAG4?
The closest documented same-family replacement is INA116UA because Texas Instruments identifies it as the same INA116 device with the same electrical configuration and 16-pin SOIC package. However, the INA116UAG4 is obsolete, and the ordered suffix may differ in packing or processing. Request the current ordering code, lifecycle status, and lot-specific qualification details before production use.
What can replace the obsolete INA116UAG4?
INA116UA is the most direct documented family option because the Texas Instruments part-details page associates it with INA116UAG4 and identifies the same 16-pin package. It is not a second-source drop-in because Texas Instruments manufactures both options. For a cross-manufacturer replacement, verify every pin, supply range, common-mode range, output swing, gain accuracy, and bandwidth rather than relying only on matching the SOIC outline.
INA116UAG4 vs INA116UA - which one should I use?
Choose INA116UA when its current ordering, packaging, and lifecycle terms are acceptable because it belongs to the same INA116 family and uses the same 16-pin SOIC configuration. The obsolete INA116UAG4 should be considered only for maintenance of existing assemblies. Texas Instruments identifies INA116UA as corresponding to INA116UAG4, but the final suffix must be checked for packing and production requirements.
When should I choose the INA116UAG4 instead of a general-purpose precision op amp?
Choose the INA116UAG4 when source impedance is high enough that input bias current dominates the measurement error and when differential input plus common-mode rejection is required. Its 3 fA typical input bias current at 25°C is substantially more appropriate for leakage-sensitive sensors than a conventional precision op amp. Confirm that the 800 kHz bandwidth and 1-to-1000 gain range satisfy the signal requirements.
Is the INA116UAG4 a drop-in replacement for INA117?
The INA116UAG4 is not a verified drop-in replacement for the INA117 because they use different package and pin arrangements despite both supporting resistor-programmed instrumentation-amplifier gain. The comparison must include physical lead mapping, supply range, common-mode range, output swing, and gain-error behavior. Use the INA117 only after comparing its datasheet pin configuration with the existing board.
How should the INA116UAG4 PCB be designed for low leakage?
Keep the INA116UAG4 input traces short and clean, keep the gain-setting resistor close to its pins, and prevent conductive contamination around the high-impedance inputs. Route guard connections according to the manufacturer datasheet and avoid nearby switching nodes or wet cleaning residue. The device's 3 fA typical input bias current at 25°C can be undermined by board leakage even when the amplifier itself performs correctly.
What is the lifecycle status of the INA116UAG4?
The INA116UAG4 is discontinued and is no longer carried by the distributor listing identified for this part. Texas Instruments continues to provide an INA116 product page and INA116UA ordering information. Use the manufacturer product page to confirm availability before committing a new production design, and use the Request a Quote form on this page for current sourcing support.
Where can I buy the INA116UAG4 and what is its current price?
Current commercial availability and price for the obsolete INA116UAG4 should be requested through the Request a Quote form on this page. The listing identifies the exact 16-pin SOIC orderable MPN, but it does not provide a current qualifying quantity-break price table. Avoid substituting a different suffix without confirming the package, grade, and production requirements.
What is the lead time for the INA116UAG4?
The current lead time for the obsolete INA116UAG4 is not stated on the product page, so it must be confirmed through the Request a Quote form. The exact MPN is identified as a discontinued 16-pin SOIC orderable part. For maintenance demand, include target quantity, acceptable packaging, required date, and traceability requirements with the request.
What are the key specifications of the INA116UAG4 that engineers should know?
The key INA116UAG4 specifications are 3 fA typical input bias current at 25°C, 25 fA at 85°C, gains from 1 to 1000, an 800 kHz -3 dB bandwidth, and a 0.8 V/µs slew rate. According to the Texas Instruments INA116 datasheet, the device uses a monolithic FET-input, three-op-amp architecture in a 16-pin SOIC package.

Data referensi kejuruteraan untuk INA116UAG4 — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose the INA116UAG4 for maintenance of an existing 16-pin SOIC design or a new precision front end when picoamp-level input bias current is essential. Its 3 fA typical bias current at 25°C, gains from 1 to 1000, 800 kHz bandwidth, and differential three-op-amp topology are particularly suitable for electrochemical sensors, photodiodes, high-impedance bridges, and current transducers. INA116UA is the closest same-family ordering option when its lifecycle, packing, and production terms are acceptable. Do not treat INA117 or INA114 as drop-in replacements without checking their package and pin assignments; related instrumentation-amplifier functions do not imply electrical or footprint compatibility. For a cross-manufacturer substitution, require complete pin mapping plus equivalent supply, common-mode, output-swing, gain-error, offset, bandwidth, slew-rate, and temperature-range coverage.

Perbandingan dengan Gantian

Parametr Produk Ini INA116UA INA116U
Brand Texas Instruments Texas Instruments Texas Instruments
Package 16-pin SOIC (UA) 16-pin SOIC (UA) 16-pin SOIC (UA)
Input Bias Current at 25°C 3 fA typical 3 fA typical 3 fA typical
Input Bias Current at 85°C 25 fA typical 25 fA typical 25 fA typical
Gain Range 1 to 1000 1 to 1000 1 to 1000
Gain-Setting Method 1 external resistor 1 external resistor 1 external resistor
Bandwidth 800 kHz -3 dB 800 kHz -3 dB 800 kHz -3 dB
Slew Rate 0.8 V/µs 0.8 V/µs 0.8 V/µs
Internal Topology 3-op-amp instrumentation amplifier 3-op-amp instrumentation amplifier 3-op-amp instrumentation amplifier
Input Stage Monolithic FET input Monolithic FET input Monolithic FET input
Number of Circuits 1 circuit 1 circuit 1 circuit

Penyeberangsung Jelas

  • Extremely low input bias current supports high-impedance sensing (vsINA117)
  • Single-resistor gain programming covers a wide measurement range (vsINA114)
  • Input guarding supports leakage-sensitive PCB layouts (vsGeneral-purpose precision operational amplifiers)

Catatan Desain

Treat the INA116UAG4 inputs as leakage-sensitive nodes. Keep the input traces short, avoid parallel copper runs beneath the inputs, and remove flux and ionic contamination after assembly. The amplifier's 3 fA typical input bias current at 25°C is exceptionally small, so PCB leakage can become comparable to the device input current. Follow the guard-pin guidance in the manufacturer datasheet and avoid placing the input loop beside switching nodes or power inductors.

Place the external gain-setting resistor close to the gain terminals to minimize susceptibility to leakage and parasitic capacitance. Maintain a symmetrical, compact differential-input route where practical, and connect the sensor or bridge directly to the input pins rather than extending sensitive traces through a connector. Grounding and guarding should be designed together so leakage currents are directed away from the input node instead of through the source impedance.

Do not select the INA116 solely by its 800 kHz bandwidth. Verify the complete operating envelope in the manufacturer datasheet, including supply voltage, common-mode input range, output swing, gain accuracy, and temperature limits. Also avoid assuming that every INA-family amplifier is pin-compatible: INA117 and INA114 comparison results identify related functions but do not establish the same 16-pin footprint or lead mapping as the INA116UAG4.

Match the bandwidth and slew rate to the sensor bandwidth rather than using the maximum gain indiscriminately. The INA116UAG4 provides 1-to-1000 gain with an 800 kHz -3 dB bandwidth and 0.8 V/µs slew rate. At high closed-loop gain, bandwidth becomes more restrictive, while excessive gain can amplify offset, noise, and leakage. Establish the usable frequency range from the complete gain equation and filter design before allocating ADC resolution.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

The product is identified as an industrial-grade instrumentation amplifier. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not established by the retrieved content.

Pencarian Berhubungan

INA116UAG4 datasheet INA116UAG4 pinout INA116UAG4 datasheet pdf INA116UAG4 equivalent INA116UAG4 replacement INA116UAG4 cross reference INA116UAG4 price INA116UAG4 stock INA116UAG4 vs INA117 INA116UAG4 vs INA114 Texas Instruments INA116UAG4 INA116UAG4 16 pin SOIC INA116UAG4 3 fA INA116UAG4 high impedance sensor INA116 instrumentation amplifier application circuit

Komponen dan Tanda berkaitan

Texas Instruments INA116UAG4 INA116UA INA116U INA116 instrumentation amplifier differential amplifier analog integrated circuit amplifier IC FET input input bias current 3 fA common-mode rejection gain setting resistor 800 kHz bandwidth 0.8 V/µs slew rate three-op-amp topology SOIC-16 UA package surface-mount package high-impedance sensor electrochemical sensor photodiode precision bridge measurement input guarding
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ