Produk (44,000+)

LM258DGKR - Dual 30V 700kHz Op Amp | Texas Instruments
LM258DGKR

LM258DGKR - Dual 30V 700kHz Op Amp | Texas Instruments

The Texas Instruments LM258DGKR is a dual, general-purpose operational amplifier rated for a 30 V supply, 700 kHz gain-bandwidth product, and operation from -25°C to 85°C. The device contains two amplifier channels in an 8-pin VSSOP (DGK) package, making it suitable for industrial signal conditioning, transducer interfaces, and general-purpose analog control circuits. An operational amplifier is an analog amplifier that uses high open-loop gain to amplify the difference between two input voltages. In the broader component hierarchy, an operational amplifier belongs to the amplifier IC and signal-conditioning categories. The LM258 combines two amplifiers in one package, allowing related measurements or control functions to share a common supply while reducing board area compared with two single amplifier packages. Key characteristics include a 30 V maximum supply rating, 700 kHz gain-bandwidth product, and typical input offset voltage of 300 µV. Its common-mode input range can extend to ground, which is useful when signals are referenced near the lower supply rail. The dual-channel configuration and 8-pin VSSOP package are particularly useful for industrial and embedded designs requiring two amplifier functions in a compact footprint. The LM258 operates from a single supply or a split supply, allowing it to work with positive-only or bipolar rail arrangements. Its 700 kHz gain-bandwidth product is appropriate for general-purpose low-frequency signal paths rather than high-speed instrumentation. Designers should account for the -25°C to 85°C commercial temperature range when planning enclosure temperature, thermal rise, and production operating conditions. Typical uses include pressure and temperature sensor conditioning, buffered control signals, low-side current measurement with a suitable sense amplifier, audio preamplification, and general industrial analog interfaces. The common-mode input capability near ground supports sensors whose output remains close to the lower rail, while the dual layout can simplify circuits requiring two closely related amplifier channels. Design attention should focus on supply decoupling, output-load limits, input common-mode boundaries, and stability with capacitive loads. Place the supply bypass capacitor close to the device and check the datasheet's output-swing and capacitive-load recommendations before driving long capacitive cables or high-capacitance loads. Add input bias-current compensation when driving high-impedance sources. This page consolidates the exact LM258DGKR ordering information, verified manufacturer characteristics, practical application guidance, and same-footprint replacement options. It also highlights where alternative amplifier families may change supply limits, temperature range, or common-mode behavior, helping engineers compare upgrades without relying on a simple function-name match.

RFC Hubungi kami
LM258DMR2 - Dual 1MHz Op Amp, 3-32V | onsemi
LM258DMR2

LM258DMR2 - Dual 1MHz Op Amp, 3-32V | onsemi

The onsemi LM258DMR2 is a dual general-purpose operational amplifier with two independent circuits, a 1 MHz gain-bandwidth product, a 3 V to 32 V supply range, and an 8-pin MSOP package. It is intended for low-cost signal conditioning, industrial control, and general-purpose analog circuits operating from a single supply or split supplies. An operational amplifier, or op amp, is an analog building block that amplifies the voltage difference between its two inputs. The LM258 belongs to the operational-amplifier hierarchy within analog and mixed-signal ICs. Its input stage can operate down to the negative supply rail, including ground in single-supply systems, which makes it useful for circuits that process signals referenced to 0 V. Key characteristics include a 1 MHz gain-bandwidth product, typical input bias current of 45 nA, and typical quiescent current of 800 µA per channel. The device supports single-supply or split-supply operation, while its common-mode input range extends to ground or VEE. These characteristics make it suitable for transducers, sensors, audio stages, feedback networks, and low-frequency control loops. The LM258 architecture uses two independent amplifier channels in one package, reducing component count and board area compared with discrete single-channel amplifiers. Its low-power design favors general-purpose applications where low quiescent current is more important than wide-bandwidth performance. The 8-MSOP outline also gives PCB designers a compact surface-mount option, although its lead pitch differs from standard SOIC and DIP packages. Typical applications include sensor amplification in industrial equipment, current-loop receivers, audio preamplifier stages, motor or actuator control interfaces, and general low-frequency signal-conditioning boards. Split-supply operation can simplify biasing around bipolar signals, while single-supply operation is useful when the signal remains near the ground rail. When designing around the LM258DMR2, verify that every input remains within the common-mode range and that output swing stays within the supply rails under load. Input bias and offset currents define the practical impedance range of source and feedback networks. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured according to the manufacturer guidance rather than left floating. This product page combines the manufacturer-device identity, verified distributor records, parameter comparison fields, and practical design guidance to support component selection, footprint review, and replacement planning for the LM258DMR2.

RFC Hubungi kami
LM258DR - Dual 30V Operational Amplifier | STMicroelectronics (Tape & Reel)
LM258DR

LM258DR - Dual 30V Operational Amplifier | STMicroelectronics (Tape & Reel)

The STMicroelectronics LM258DR is a dual, internally frequency-compensated operational-amplifier IC with two independent amplifiers, a 30 V maximum supply rating and a 700 kHz gain-bandwidth product. Each amplifier is designed for general-purpose signal conditioning from single or split supplies. The device is packaged for surface mounting in an 8-pin SOIC and is identified by the DigiKey listing as a standard, general-purpose, two-circuit amplifier. The supplied source data confirms the 30 V and 700 kHz headline ratings through Texas Instruments’ LM258 family page, but it does not provide a complete STMicroelectronics parameter table. An operational amplifier is a voltage-gain element that uses external feedback to control closed-loop behavior. The LM258DR belongs to the dual operational-amplifier hierarchy and contains two independent amplifiers in one package. Internal frequency compensation makes each amplifier stable without an external compensation network in many voltage-follower and conventional feedback configurations. Its common-mode range extending toward ground, together with single-supply operation, makes this device class useful in battery-powered, industrial-control and instrumentation circuits where the signal can approach the lower supply rail. The principal design benefit is integration: two amplifiers occupy one 8-SOIC package rather than requiring two separate single amplifiers. Both channels can amplify a pair of related signals, form two halves of an active filter, or implement independent comparators and buffers. The 700 kHz gain-bandwidth product supports moderate-frequency signal paths, while the 30 V supply class accommodates higher-voltage industrial rails. Designers must still check input range, output swing, slew rate, offset, bias current and load capability against the exact manufacturer datasheet before releasing production hardware. Technically, internal frequency compensation trades bandwidth and other performance characteristics for ease of use. Stable operation does not make every feedback topology valid, and real circuits still require attention to output loading, input common-mode range, supply decoupling and stability around capacitive loads. Two amplifiers do not share their supply pins internally at the component level, so both sections use the package’s common positive and ground connections. PCB grounding and bypass placement determine whether the theoretical noise and transient performance can be realized. Typical applications include transducer-signal conditioning, low-side current measurement, loop-error amplification, active filtering, audio preamplification, motor-control interfaces and general dual-rail amplification. A single-supply sensor circuit can use one amplifier for conditioning and the other for an offset, filter or intermediate buffer stage. Split-supply instrumentation can use both channels more independently. Compared with modern low-voltage rail-to-rail amplifiers, the LM258DR trades compactness and precision for its wide-supply capability and straightforward general-purpose use. When designing around the LM258DR, place the supply bypass capacitor close to the IC and route each amplifier’s inputs and outputs to minimize leakage and feedback-loop pickup. Confirm that signals stay within the common-mode and output-swing limits under the worst supply, temperature and load conditions. Do not treat a distributor cross-reference result as proof of equivalence; verify pin mapping, electrical limits, stability and temperature grade in the selected replacement manufacturer’s datasheet. This page combines the verified distributor identification, official family-page information, cross-reference evidence and package-level design guidance. It distinguishes confirmed facts from parameters that were not supplied, avoiding invented precision while helping engineers evaluate LM258DR procurement, replacement and circuit-integration decisions.

RFC Hubungi kami
LM258DR2 - Dual 3-32V Op Amp | onsemi | 8-SOIC IC
LM258DR2

LM258DR2 - Dual 3-32V Op Amp | onsemi | 8-SOIC IC

onsemi LM258DR2 is a dual general-purpose operational amplifier designed for single-supply or split-supply operation across a 3 V to 32 V operating range. The device provides two amplifiers in an 8-pin SOIC package, with a common-mode input range extending to ground or VEE. Its 700 kHz gain-bandwidth product supports general signal-conditioning and feedback-control applications where a straightforward, widely supported dual amplifier is preferred. An operational amplifier is an analog building block that compares two input voltages and amplifies the difference between them. The LM258 belongs to the dual-operational-amplifier hierarchy within linear amplifier ICs and broader semiconductor devices. Its two channels can amplify or buffer independent signals within one package, reducing board area compared with separate single-channel amplifiers while preserving familiar industry-standard pin assignments. The LM258DR2 emphasizes low power drain, operation from a single 3 V to 32 V supply, and common-mode input operation toward ground or VEE. These characteristics make it useful in battery-powered instrumentation, industrial control systems, sensor-conditioning circuits, audio preamplifiers, and general feedback networks. The dual configuration also allows related channels to be used as an amplifier and buffer within the same package. With a gain-bandwidth product of 700 kHz, the LM258 is suited to moderate-bandwidth analog signal paths rather than high-speed or precision applications requiring substantially greater bandwidth or lower offset. The split-supply capability permits operation around a midpoint reference, while the single-supply mode supports systems where the signal remains near the lower supply rail. Input, output, and supply limits must be respected during design. Typical uses include low-frequency sensor amplification, audio signal conditioning, audio preamplifiers, active filters, comparators with added feedback, and industrial process-control interfaces. The LM258DR2 is particularly suitable when two conventional amplifier channels are needed without the extra operating supply or board area associated with dual-rail-only precision amplifiers. Designers should preserve the standard SOIC-8 footprint and verify the manufacturer's pin-description table before routing the PCB. Input common-mode and output swing limits depend on the selected supply voltage and load. Decoupling close to the supply pins, adequate output-current capacity, and stable feedback compensation are essential for dependable operation. This product page combines package, application, pinout, sourcing, and replacement guidance with practical design considerations. It also distinguishes verified device attributes from parameters that require confirmation with the manufacturer datasheet before release to production.

RFC Hubungi kami
LM258DR2G - Dual 3-32V Op Amp | onsemi | Industrial
LM258DR2G

LM258DR2G - Dual 3-32V Op Amp | onsemi | Industrial

The onsemi LM258DR2G is a dual, internally compensated general-purpose operational amplifier operating from 3 V to 32 V in an 8-pin SOIC package. It provides two amplifier channels, a typical slew rate of 0.6 V/µs, and an operating temperature range of -25°C to +85°C. The device is designed for single-supply or split-supply operation, with common-mode input voltage that extends to ground and to VEE. An operational amplifier is an analog signal-conditioning device that uses high open-loop gain to amplify the difference between two input voltages. The LM258 belongs to the general-purpose operational-amplifier family within the broader amplifier, analog IC, and semiconductor hierarchies. Its internally compensated architecture simplifies stable operation without an external compensation network, making it useful in industrial control, sensor conditioning, and general analog signal-processing systems. Key characteristics include a low typical supply-current drain of 0.7 mA, typical input-offset voltage of 2 mV, typical input-offset current of 2 nA, and typical input-bias current of 15 nA. The common-mode range reaches the lower supply rail, which supports direct sensing of signals near ground in single-supply systems. A 32 V maximum differential input range matches the stated maximum supply capability. The LM258's internally stabilized design provides approximately 0.6 V/µs slew rate and unity-gain stability, allowing it to function directly in voltage-follower, amplifier, comparator-style, and feedback-control circuits. Its 32 V operating capability supports higher supply rails than many low-voltage precision amplifiers, while the two-channel SOIC package reduces board area compared with discrete single amplifiers. Typical uses include industrial sensor interfaces, low-side current measurement, control-loop amplifiers, audio preamplifier stages, and general-purpose signal conditioning. The device is especially appropriate when the circuit must tolerate a broad supply range, operate near the ground rail, and avoid external frequency-compensation components. When designing around the LM258DR2G, account for input offset and bias currents when using high-impedance sensors. Place input and feedback components close to the package, maintain stable reference and feedback paths, and verify common-mode and output-swing limits against the actual supply voltage. This page combines electrical characteristics, package details, replacement options, and practical application guidance for faster engineering evaluation.

RFC Hubungi kami
LM258DRE4 - Dual 30V 700kHz Op Amp | Texas Instruments
LM258DRE4

LM258DRE4 - Dual 30V 700kHz Op Amp | Texas Instruments

The Texas Instruments LM258DRE4 is a dual general-purpose operational amplifier rated for 30 V operation, featuring a 700 kHz gain-bandwidth product and a typical slew rate of 0.3 V/µs. The device contains two amplifiers in an 8-pin SOIC package and is intended for operation from -25°C to +85°C. Its 0.7 mA typical supply-current drain supports low-power signal-conditioning systems operating from single or dual supplies. An operational amplifier is an analog integrated circuit that uses high-gain differential amplification to process signals whose voltage lies above or below its supply rails. In the electronics hierarchy, the LM258 is a general-purpose operational amplifier, a dual amplifier, and ultimately an analog semiconductor. Its internal frequency compensation, common-mode input range that includes ground, and low bias current make it useful for amplifying weak signals without requiring an external compensation network. The LM258DRE4 combines a 700 kHz gain-bandwidth product with a 0.3 V/µs slew rate, allowing relatively low-frequency control, sensing, and buffering functions to be handled without an external compensation network. Typical input offset voltage is 3 mV, while typical input offset current is 2 nA and typical input bias current is 20 nA. The device also accepts differential input voltages up to 32 V, although the 30 V maximum supply rating remains the governing operating limit. Both amplifier channels share the same pinout and common supply connections, allowing one IC to implement two related signal-processing functions. The SOIC-8 construction uses gull-wing leads and supports conventional surface-mount assembly. Because the amplifiers are not rail-to-rail output devices, output swing and common-mode behavior must be checked against the selected supply voltages and load. Input-referred offset and bias characteristics are especially important when the source impedance is high or when precision DC measurements are required. Typical LM258DRE4 applications include industrial sensor conditioning, low-frequency active filters, audio preamplifier stages, voltage-controlled amplifiers, relay-driver interfaces, and general-purpose DC signal amplification. The 30 V capability accommodates 24 V industrial systems when the signal and supply voltages remain within the device limits. The low 0.7 mA typical supply-current drain is useful where multiple amplifier channels must operate continuously within a limited power budget. The principal design trade-off is its 700 kHz bandwidth: this is ample for many sensor, control, and audio tasks but too slow for high-speed instrumentation or communications waveforms. Input bias current of 20 nA typical can create offset errors across high source impedances, and the 3 mV typical input offset should be included in overall accuracy budgets. Decoupling, grounding, and output-load stability must be evaluated using the manufacturer application guidance. This page consolidates the device specifications, pin assignments, sourcing information, and practical alternatives into an engineering-focused reference. It also distinguishes true package-compatible replacements from parts that merely perform a similar amplifier function, helping designers preserve PCB layout, supply compatibility, and signal-chain performance during obsolescence or second-source evaluation.

RFC Hubungi kami
LM258DRG4 - Dual 700 kHz Operational Amplifier | Texas Instruments
LM258DRG4

LM258DRG4 - Dual 700 kHz Operational Amplifier | Texas Instruments

The Texas Instruments LM258DRG4 is a dual general-purpose operational amplifier with a 30 V maximum supply rating, 700 kHz gain-bandwidth product, and 0.3 V/µs slew rate, packaged in an 8-pin SOIC. The device provides two independent amplifiers and supports single-supply or split-supply operation across ±1.5 V to ±16 V, making it suitable for industrial control, sensor conditioning, and audio signal-chain applications. An operational amplifier is an analog integrated circuit that uses high open-loop gain and negative feedback to amplify small voltage differences. Within the power-management and signal-processing hierarchy, an operational amplifier acts as a high-gain voltage-feedback block. The LM258 combines two amplifiers in one package, reducing board area while providing common input, output, and supply rails for both channels. Key features include a 700 kHz gain-bandwidth product, 0.3 V/µs slew rate, and operation from a single 3 V supply through split supplies of up to 30 V total. Its -25°C to 85°C operating-temperature range targets general-purpose industrial equipment. The SOIC-8 package also provides a conventional footprint and lead spacing for designs using through-hole-compatible surface-mount assembly methods. The LM258 architecture is intended for stable operation with conventional feedback networks rather than rail-to-rail input and output operation. Input common-mode range, output swing, supply voltage, load capacitance, and feedback-loop stability must be checked against the application. Its relatively high bandwidth supports general-purpose AC signal amplification, although higher-speed or precision amplifier families may be preferable for demanding instrumentation. Typical uses include transducer and bridge-amplifier front ends, low-frequency active filters, audio preamplification, voltage followers, comparator-style interfaces, and industrial control signal conditioning. Two amplifiers in one package are especially useful when one channel performs filtering and the second buffers or amplifies the resulting signal. Split-supply operation also supports bipolar sensor signals centered around ground. For a new layout, place input and output components close to the appropriate pins and maintain a quiet return path for both channels. Check the manufacturer datasheet for common-mode limits, output-swing restrictions, recommended resistor values, and stability requirements before operating near the supply rails or driving capacitive loads. This page combines the manufacturer specifications with practical design guidance, application selection, and verified pin-compatible alternatives for engineers evaluating the LM258DRG4 in legacy and new analog signal-chain designs.

RFC Hubungi kami
LM258DT - Dual 30V Low-Power Op Amp | STMicroelectronics
LM258DT

LM258DT - Dual 30V Low-Power Op Amp | STMicroelectronics

The STMicroelectronics LM258DT is a low-power, dual, internally frequency-compensated operational amplifier with two independent amplifiers, a 3 V to 30 V single-supply operating range, and an 8-pin SOIC package. Its unity-gain bandwidth is 1.1 MHz, while its slew rate is 0.6 V/us. The device is designed for single-supply operation over a wide voltage range and provides large DC voltage gain of 100 dB. An operational amplifier is an analog signal-conditioning IC that uses high open-loop gain and negative feedback to amplify, buffer, filter, or compare voltages. The LM258DT belongs to the bipolar operational-amplifier family and combines two amplifiers in one package, reducing board area when a circuit needs matched general-purpose gain stages. Its internally frequency-compensated architecture simplifies closed-loop design because the compensation network is integrated rather than added externally. Each amplifier offers a unity-gain bandwidth of 1.1 MHz and a slew rate of 0.6 V/us, making the device suitable for audio-frequency signal paths, sensor conditioning, active filtering, voltage amplification, and general feedback-control blocks. The low-power supply drain is approximately 500 uA per amplifier and is essentially independent of supply-voltage magnitude. The low input bias current of approximately 20 nA also helps minimize source-loading errors in high-impedance sensing circuits. The dual architecture supports independent signal paths, including two noninverting stages, two inverting stages, mixed gain stages, or a buffer paired with an active filter. Both amplifiers share the same supply pins but operate independently. Their common supply range allows them to use a single rail in portable instrumentation, industrial control, sensor interfaces, and low-voltage embedded systems. The 8-SOIC package is suitable for conventional surface-mount PCB assembly and temperature-controlled lead-free manufacturing processes. Designers should account for input and output voltage limitations when using a single positive supply. The LM258DT is not a rail-to-rail input or output device, so the usable signal range must remain inside the common-mode and output-swing limits stated in the manufacturer datasheet. Place bypassing capacitors close to the supply pins and maintain adequate PCB copper for heat dissipation. Stable operation also depends on selecting appropriate feedback components and avoiding capacitive loading directly at the amplifier output. This product page combines the LM258DT electrical characteristics, package and pin information, application guidance, comparison criteria, and practical design considerations into a compact engineering reference for initial design decisions.

RFC Hubungi kami
LM258H - Dual 30V 700kHz Op Amp | Texas Instruments
LM258H

LM258H - Dual 30V 700kHz Op Amp | Texas Instruments

The Texas Instruments LM258H is a dual general-purpose operational amplifier with a 30 V supply rating, 700 kHz gain-bandwidth product, and operation from -25°C to 85°C. The LM258H is supplied in the metal-can TO-99-8 package and provides two amplifiers per package. Its precision-oriented counterpart grades, including the LM358 family, use the same dual-amplifier architecture for common industrial signal-conditioning designs. An operational amplifier is an active semiconductor device that uses high-gain differential amplification to increase the voltage difference between its differential input and drive its output. Operational amplifiers belong to the amplifier IC hierarchy and are commonly used in sensor interfaces, buffer stages, integrators, comparators, and control loops. The LM258 family is positioned as a general-purpose bipolar amplifier rather than a high-speed, low-noise, or precision-specific device. The manufacturer identifies the LM258 family as dual, 30 V, 700 kHz operational amplifiers. The LM258H ordering variant is associated with the TO-99-8 metal-can package, while the broader LM258 family also includes other package and temperature options. The verified distributor listing describes LM258H as a two-circuit amplifier in a TO-99-8 package. The H suffix is used in the manufacturer ordering information, but individual suffix-specific electrical values must be confirmed against the ordering table in the manufacturer datasheet. The 700 kHz gain-bandwidth product is the principal verified speed parameter. It describes the approximate closed-loop bandwidth available for unity-gain operation under the stated test conditions, subject to the manufacturer datasheet's load and test assumptions. The 30 V rating identifies the device as suitable for higher-voltage analog signal chains than basic low-voltage single-supply amplifiers, provided the selected grade and supply arrangement meet the complete datasheet limits. Operating temperature is specified from -25°C to 85°C for the LM258 family. Typical uses include buffered sensor signals, low-frequency active filters, analog summing and difference amplifiers, current-loop buffering, audio and communications signal conditioning, and general industrial control interfaces. Because the verified data does not provide output-current, input-offset, noise, slew-rate, load-current, common-mode, or package-dimension values, those parameters should not be inferred for design calculations. Engineers should use the manufacturer datasheet for the exact LM258H grade limits and test conditions. The main design consideration is ensuring that the selected dual amplifier's pinout, supply voltages, input common-mode range, output swing, and load conditions match the completed analog design. TO-99-8 is a through-hole metal-can package, so PCB footprint selection and mechanical clearance require the package drawing rather than a modern SMD assumption. Decoupling, grounding, and stable feedback compensation remain necessary even when using a general-purpose amplifier. This page combines the verified manufacturer product identity, distributor package information, ordering context, and design-oriented interpretation. It also distinguishes verified LM258 family facts from parameters that still require confirmation from the manufacturer datasheet, helping engineers move from part selection to a qualified schematic without inserting unsupported assumptions.

RFC Hubungi kami
LM258N - Dual 32 V 700 kHz Op Amp | Amplifier IC
LM258N

LM258N - Dual 32 V 700 kHz Op Amp | Amplifier IC

The LM258N is a dual, general-purpose operational amplifier designed for single-supply operation over a 3 V to 30 V range, with a stated 32 V maximum supply rating in the verified product data. It provides two independent amplifiers in an 8-pin Mini DIP package and operates from -25°C to 85°C. Each channel combines a high-gain, internally frequency-compensated architecture with a typical gain-bandwidth product of 1.1 MHz and a typical slew rate of 0.6 V/µs. The device is intended for general-purpose signal conditioning, transducer interfaces, and low-frequency analog control applications. An operational amplifier is a high-gain analog building block that compares two input voltages and drives its output to reduce their difference. A differential input amplifier, voltage follower, comparator-style interface, or control loop can be built around the LM258N when the required bandwidth, slew rate, supply voltage, and input/output range fit the device. The LM358-family architecture also allows operation from a single supply or split supply, making it useful in systems whose signal is referenced near ground. Verified product information identifies the LM258-N as a dual 32 V, 700 kHz operational amplifier with -25°C to 85°C operation. The related LM258N distributor listings identify an 8-pin Mini DIP package and a general-purpose dual amplifier configuration. The device is therefore suited to industrial and instrumentation circuits where a through-hole package and wide supply range are useful, provided the circuit designer checks the exact manufacturer datasheet for input common-mode limits, output swing, supply current, offset voltage, and thermal limits. The internally compensated amplifiers simplify implementation of unity-gain and conventional inverting or non-inverting stages because no external compensation network is required for ordinary closed-loop use. The 1.1 MHz gain-bandwidth product supports many low-frequency signal paths, while the 0.6 V/µs slew rate limits large-signal response. These characteristics make the LM258N more appropriate for instrumentation, buffering, and control than for high-speed signal chains. Typical uses include sensor signal conditioning, low-frequency active filters, audio and communications interface stages, analog control loops, and general dual-amplifier boards. In a single-supply circuit, the input and output signal ranges must remain inside the device's allowable common-mode and output-swing limits. The 8-pin DIP package also favors through-hole prototyping and repairable industrial assemblies. For PCB layout, keep input and feedback paths short, provide a solid ground reference, and place decoupling capacitors close to the supply pins. Avoid placing noisy switching nodes beside high-impedance input traces. Because the verified data does not provide every electrical limit, exact compliance status, pricing, or an official pin mapping for the generic LM258N ordering code, those details remain marked as data needed rather than inferred.

RFC Hubungi kami
LM258NG - Dual 1MHz Operational Amplifier | onsemi
LM258NG

LM258NG - Dual 1MHz Operational Amplifier | onsemi

onsemi LM258NG is a dual, general-purpose operational amplifier with a 1 MHz gain-bandwidth product, 0.6 V/µs slew rate, and operation from 3 V to 32 V in an 8-pin PDIP package. The device provides two amplifier circuits in one through-hole package and supports single-supply or split-supply operation. Its common-mode input voltage range extends toward ground or VEE, making it suitable for industrial, instrumentation, control, and signal-conditioning systems where single-rail operation is advantageous. An operational amplifier is a high-gain differential amplifier used to amplify, buffer, compare, or integrate signals. The LM258NG belongs to the dual general-purpose operational-amplifier class and within the broader hierarchy of analog ICs, analog signal-chain components, and semiconductor devices. Unlike rail-to-rail precision amplifiers, its practical input and output ranges depend on its supply voltage and circuit configuration. Designers should therefore evaluate common-mode range, output swing, input bias current, and load capability against their signal levels. The principal verified characteristics are a 1 MHz gain-bandwidth product, 0.6 V/µs slew rate, dual-circuit construction, and a 3 V to 32 V operating supply range. The low-power-drain architecture is useful in battery-powered or space-constrained equipment, while the common-mode range extending to ground or VEE improves usefulness in systems powered from one positive rail. The 8-pin PDIP package also supports conventional through-hole assembly and socket-level serviceability. The LM258NG architecture is suited to general-purpose feedback stages rather than high-speed signal chains. A 1 MHz gain-bandwidth product provides usable bandwidth at modest closed-loop gains, while the 0.6 V/µs slew rate limits how quickly output voltage can follow a changing input. In gain configurations with substantial noise gain, the available closed-loop bandwidth is lower. Stable feedback-network design and appropriate output loading are therefore necessary to avoid oscillation or slew-limited operation. Typical uses include low-frequency sensor signal conditioning, industrial control-loop amplifiers, audio preamplification, comparators with external hysteresis, and buffered instrumentation inputs. The dual configuration can implement two independent amplifier sections on one PCB. In a single-supply circuit, input and output grounding must be referenced carefully because the common-mode range reaches ground or VEE but is not necessarily a rail-to-rail input specification. A key design consideration is power-supply decoupling: place a suitable bypass capacitor close to each supply pin and route return currents without splitting analog ground paths. Check output swing and load current at the lowest supply voltage, and use output isolation when driving capacitive loads. These checks are especially important because the available verified data does not specify detailed offset, bias-current, thermal, or output-drive limits. This page consolidates verified distributor specifications, package information, practical application guidance, and verified web-data drop-in candidates. It also distinguishes confirmed facts from parameters that still require confirmation from the manufacturer datasheet, helping engineers identify the LM258NG quickly while avoiding unsupported assumptions.

RFC Hubungi kami
LM258P - Dual 30 V 700 kHz Op Amp | Texas Instruments
LM258P

LM258P - Dual 30 V 700 kHz Op Amp | Texas Instruments

The Texas Instruments LM258P is a dual, internally frequency-compensated operational amplifier with a 30 V supply rating, 700 kHz gain-bandwidth product, and operation from -25°C to 85°C, housed in an 8-pin PDIP package. One package contains two independent amplifiers, making it suitable for dual-channel signal conditioning, transducers, control loops, and general-purpose analog systems. An operational amplifier is a voltage-gain building block within analog and mixed-signal electronics. The LM258P belongs to the bipolar operational-amplifier family, combining differential inputs, high voltage gain, internal frequency compensation, and common operation from a single or split supply. Its two independent channels allow simultaneous amplification, filtering, buffering, or feedback control without requiring two separate amplifier packages. The verified source data identifies a wide supply-voltage operating range, high DC voltage gain, unity-gain bandwidth, low supply current, and low input-bias current. The search results specifically identify 100 dB large DC voltage gain, 1.1 MHz unity-gain bandwidth, approximately 500 µA supply current per amplifier, and approximately 20 nA input-bias current. These characteristics make the device relevant to instrumentation where useful closed-loop accuracy is more important than very high speed. Each amplifier is independently compensated, allowing normal operation without external frequency-compensation components. Input and output-device choices support practical single-supply and split-supply arrangements, while the dual configuration can reduce board area in paired channels. Nevertheless, output-current capability, common-mode limits, input-offset behavior, noise, and stability should be checked against the complete manufacturer datasheet before precision or load-heavy use. Typical uses include transducer signal conditioning, low-frequency active filters, sensor amplification, instrumentation amplifiers, sample-and-hold interfaces, and industrial control loops. The 8-pin PDIP package is appropriate for through-hole assembly and prototypes, and its wide temperature coverage supports equipment operating across industrial temperature ranges. PCB design should keep input and feedback paths short, provide adequate supply bypassing, and maintain a stable reference or mid-supply point when the output must remain biased above ground in single-supply operation. Avoid relying on the verified snippets for load-current or saturation limits; those values require the complete LM258 manufacturer datasheet. This page consolidates the verified LM258P identity, package, temperature, supply, bandwidth, gain, current, pricing, and sourcing information with engineering guidance. It also distinguishes verified facts from parameters that still require full-datasheet confirmation, providing a practical basis for initial design and procurement review.

RFC Hubungi kami
LM258PG4 - Dual 30V 700kHz Op Amp | Texas Instruments
LM258PG4

LM258PG4 - Dual 30V 700kHz Op Amp | Texas Instruments

The Texas Instruments LM258PG4 is a dual, general-purpose operational amplifier with a 30 V maximum supply rating, 700 kHz gain-bandwidth product, and 0.3 V/µs slew rate, housed in an 8-pin PDIP package. The two amplifiers are designed for instrumentation, signal-conditioning, and control applications operating from single or dual supplies. An operational amplifier is a high-gain analog building block used to amplify, buffer, filter, compare, or drive external signals. The LM258 belongs to the dual-operational-amplifier hierarchy within the broader categories of analog IC, amplifier IC, and semiconductor. Its internally compensated architecture simplifies design by eliminating the need for an external compensation network in typical closed-loop configurations. The principal performance features include a 700 kHz gain-bandwidth product, 0.3 V/µs slew rate, and approximately 500 µA quiescent current per channel. These ratings make the device suitable for general-purpose voltage amplification, current-to-voltage conversion, active filtering, transducers, and industrial control loops. Its 30 V supply rating also provides additional headroom for industrial systems operating from higher-voltage rails than conventional low-voltage mixed-signal circuits. Each channel contains an input differential pair, voltage-amplification stage, output stage, and internal frequency compensation. Because the amplifiers are independent, they can amplify two separate signals or be configured as one differential amplifier plus one additional signal channel. The 700 kHz bandwidth supports general-purpose closed-loop operation rather than the much wider bandwidth associated with precision, high-speed, or FET-input amplifier families. Typical uses include sensor-interface amplification, industrial instrumentation, audio preamplification, active filters, relay and solenoid-driver stages, and low-frequency control systems. The dual configuration can reduce board area when two analog channels are required, while through-hole PDIP construction can simplify prototyping, inspection, and manual assembly. Designers should verify input common-mode range, output swing, input bias current, offset voltage, noise, and output-current limits against the manufacturer datasheet for the selected operating point. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured according to the datasheet rather than left open. This product page combines the LM258PG4 family specifications, ordering information, package details, and practical selection guidance with same-footprint alternatives. It is intended to help engineers move from circuit requirements to a defensible dual-op-amp selection without relying on generic amplifier-family descriptions.

RFC Hubungi kami
LM258PT - Dual 1.1 MHz Low-Power Op Amp | STMicroelectronics
LM258PT

LM258PT - Dual 1.1 MHz Low-Power Op Amp | STMicroelectronics

The STMicroelectronics LM258PT is a dual low-power bipolar operational amplifier packaged in an 8-pin TSSOP. Each of its two independent, internally frequency-compensated amplifiers provides a 100 dB large-signal voltage gain, a 1.1 MHz unity-gain bandwidth, and approximately 500 uA of supply current per amplifier. The device is designed for single-supply operation across a wide voltage range and supports general-purpose signal conditioning. An operational amplifier, or op amp, is a high-gain differential-input amplifier whose inverting and non-inverting inputs produce a single-ended output. Internally frequency-compensated op amps such as the LM258PT are internally stabilized for unity-gain operation without an external compensation network. This makes them suitable for amplifier, buffer, comparator, transducer, and feedback-control circuits where simplicity and low quiescent current are more important than very high bandwidth. Key characteristics include two amplifier circuits in one package, a large DC voltage gain of 100 dB, a 1.1 MHz unity-gain bandwidth, approximately 500 uA of supply current per amplifier, and a typical input bias current of 20 nA. Because the two channels are independent, engineers can use them for cascaded gain stages, differential signal conditioning, active filtering, or separate control and monitoring functions. The internal frequency compensation eliminates the need for external dominant-pole components in most unity-gain applications. The LM258PT is a bipolar-input general-purpose amplifier rather than a rail-to-rail CMOS op amp. Its design is appropriate when a single supply rail is available, input-referred offset is not the dominant system requirement, and operation from a non-rail-to-rail output range is acceptable. Designers must still account for the output-swing limits, common-mode input range, stability requirements, and load capability described by the manufacturer datasheet. Typical uses include low-frequency transducer amplification, sensor signal conditioning, audio preamplification, battery-powered instrumentation, feedback amplifiers in control loops, and general dual-amplifier boards. Its 8-pin TSSOP footprint permits compact surface-mount layouts, while the low 500 uA-per-amplifier supply current helps preserve battery life in portable systems. The main design consideration is stability around the op amp. Place input and output components close to their associated pins, verify capacitive loading against the datasheet stability limits, and avoid driving the output into hard clipping when the input signal exceeds the available output swing. Using the device as a unity-gain buffer requires particular care with capacitive loads because the internal compensation is optimized for a specified load range. This page consolidates manufacturer and distributor information, package details, verified pricing, drop-in alternatives, application guidance, and design notes. It is intended to complement the manufacturer datasheet with selection and implementation context that is not normally presented on a distributor listing page.

RFC Hubungi kami
LM258QT - Dual 1.1MHz Op Amp | STMicroelectronics
LM258QT

LM258QT - Dual 1.1MHz Op Amp | STMicroelectronics

The STMicroelectronics LM258QT is a low-power dual operational amplifier with two independent, internally frequency-compensated amplifiers, a 1.1 MHz unity-gain bandwidth, 100 dB large-signal voltage gain, and an 85 dB common-mode rejection ratio. The device is supplied in an 8-pin DFN package measuring 2 x 2 mm and operates from 3 V to 30 V on a single supply or from ±1.5 V to ±15 V on dual supplies. An operational amplifier is a high-gain analog signal-conditioning IC that compares differential input voltages and amplifies the result. The LM258QT belongs to the operational amplifier hierarchy, where it combines amplifier signal gain, input protection, frequency compensation, and output-current capability in one package. Its two independent channels make it useful for dual-channel signal paths, instrumentation, transducer amplification, and general-purpose analog control. Key features include a 1.1 MHz gain-bandwidth product, 0.6 V/µs slew rate, 2 mV input offset voltage, approximately 20 nA input bias current, and 100 dB DC voltage gain. The low-power architecture is intended for operation across a broad supply-voltage range, while internal frequency compensation avoids the need for external compensation components in standard closed-loop configurations. The two amplifiers are independent, allowing them to amplify different signals or drive separate analog stages. Its 85 dB CMRR helps reject common-mode interference, while its 0.6 V/µs slew rate supports moderate signal slewing requirements. The 1.1 MHz bandwidth is appropriate for low-to-moderate-frequency precision and control circuits rather than high-speed video or RF signal chains. Typical applications include sensor and transducer signal conditioning, industrial control loops, low-frequency measurement instrumentation, audio preamplification, and general-purpose dual-channel amplification. The two-amplifier configuration can reduce component count when a board needs two related analog functions, provided both channels have compatible signal ranges and grounding requirements. Designers should preserve the datasheet-recommended bypass capacitance, verify output swing and load-current limits, and account for input common-mode range near the supply rails. The DFN-8 package also requires careful PCB layout, exposed-pad thermal management, and short feedback and input paths to preserve stability and reduce parasitic effects. This page consolidates verified distributor pricing, package and electrical details, practical application guidance, and pin-compatible replacement information. It also highlights the LM258QT's key engineering trade-offs so purchasing and design decisions can be made against verified source data rather than generic operational-amplifier assumptions.

RFC Hubungi kami
LM258WYDT - Dual 1.1MHz Operational Amplifier | STMicroelectronics
LM258WYDT

LM258WYDT - Dual 1.1MHz Operational Amplifier | STMicroelectronics

The STMicroelectronics LM258WYDT is a dual general-purpose operational amplifier with two amplifier circuits, a gain-bandwidth product of 1.1 MHz, and an 8-SOIC package. It is designed for instrumentation, signal-conditioning, industrial-control, and automation applications requiring two amplifiers in one package. The -W option provides the extended industrial temperature range, while the Y suffix identifies the SOIC package and T identifies tape-and-reel packing. An operational amplifier, or op amp, is an active semiconductor device that amplifies the voltage difference between its two input terminals. Its high open-loop gain, high input impedance, and low output impedance make it useful in amplifier, buffer, comparator, summing, filtering, and current-control circuits. The dual LM258 family combines two independent amplifiers in one package, reducing component count and simplifying PCB layout. The LM258WYDT provides two amplifier circuits in an 8-SOIC package and operates at a gain-bandwidth product of 1.1 MHz. Its general-purpose design is suitable for low-frequency instrumentation and industrial signal paths rather than high-speed precision applications. The extended-temperature -W grade is intended for environments beyond the standard commercial temperature range, subject to the operating limits in the STMicroelectronics datasheet. The LM258 architecture supports operation from a single supply or split supplies, allowing its input and output signals to be referenced near ground when lower supply voltages are required. Because the two amplifiers share one package, careful decoupling and grounding remain important: each supply rail should have local bypass capacitance, and the common ground path should minimize voltage-drop-induced errors. Typical uses include process-control loops, sensor conditioning, current monitoring, audio and communications interfaces, industrial data acquisition, and general-purpose analog signal conditioning. Each channel can be used independently as an inverting or non-inverting amplifier, voltage follower, comparator, or active-filter building block, provided the input, output, and common-mode ranges remain inside the datasheet limits. When laying out the circuit, place the supply bypass capacitors close to the package power pins and route sensitive input and feedback connections away from switching nodes and high-current returns. Check output swing, input common-mode range, stability, and output-current requirements against the actual supply voltage and load before releasing the design. This product summary combines the LM258WYDT device identity, package information, application guidance, and verified drop-in alternatives with practical design considerations for engineers evaluating an 8-SOIC dual op amp.

RFC Hubungi kami
LM258WYPT - Dual 30V Low-Power Op Amp | STMicroelectronics
LM258WYPT

LM258WYPT - Dual 30V Low-Power Op Amp | STMicroelectronics

STMicroelectronics LM258WYPT is a dual, internally frequency-compensated operational amplifier designed for low-power single-supply operation. The device provides two independent amplifiers, a 30 V maximum supply rating, approximately 1.1 MHz gain-bandwidth product, 0.6 V/µs slew rate, 85 dB open-loop gain, and 2 mV input offset voltage. It is packaged for surface-mount assembly in an 8-pin TSSOP tape-and-reel format. A low-power dual operational amplifier is an analog signal-conditioning IC that provides voltage gain while remaining usable from a single positive supply. In the product hierarchy, the LM258 belongs to operational amplifiers, analog amplifiers, analog signal-processing ICs, and broader semiconductor components. Its internally compensated architecture simplifies design because each amplifier does not require an external compensation network for ordinary closed-loop operation. The LM258WYPT emphasizes low supply current, approximately 700 µA, with a supply drain that remains largely independent of supply magnitude. Its 20 nA input bias current suits many high-impedance sensing paths, while the 1.1 MHz gain-bandwidth product supports general-purpose signal conditioning at low frequencies. The two amplifiers are independent, allowing simultaneous channel processing or use in unrelated circuit blocks. Internally frequency compensation stabilizes operation in common feedback configurations. The 600 V/µs slew rate provides useful response for audio, transducer, and industrial control signals, although the device is not optimized for high-speed precision applications. The 85 dB open-loop gain and 2 mV offset specification define its practical precision in feedback-based amplifier stages. Typical uses include low-frequency sensor amplification, audio preamplification, bridge-amplifier signal conditioning, current-loop interfaces, and general industrial control. The 30 V supply capability also permits operation from higher-voltage rails when the signal amplitude remains within the amplifier's input and output limits. Independent amplifiers make the device useful in dual-channel transducers and compact analog front ends. Designers should verify common-mode and output-swing limits against the selected supply voltage, provide suitable bypassing near the power pins, and account for input bias current when working with high-source-impedance sensors. Stable feedback layout, short output paths, and clean grounding remain important because PCB leakage and leakage current can disturb sensitive measurements even when the amplifier itself performs correctly. This page combines package, electrical, application, sourcing, and replacement information into an engineering-focused guide. It also distinguishes the exact LM258WYPT order code from related LM258 variants whose temperature grade, offset bin, package, or tape-and-reel suffix can differ.

RFC Hubungi kami
LM258YDT - Dual 1.1 MHz Op Amp, 8-SOIC | STMicroelectronics
LM258YDT

LM258YDT - Dual 1.1 MHz Op Amp, 8-SOIC | STMicroelectronics

The STMicroelectronics LM258YDT is a dual, internally frequency-compensated operational amplifier with two amplifier circuits, 100 dB DC voltage gain, 1.1 MHz unity-gain bandwidth, and 0.6 V/us slew rate in an 8-pin SOIC package. Designed for general-purpose signal amplification, the LM258YDT supports low-power applications requiring two amplifiers in one package. An operational amplifier is an analog semiconductor that uses high open-loop gain to amplify voltage differences. Its broader hierarchy is operational amplifier, analog amplifier, linear integrated circuit, and semiconductor. Internally frequency-compensated devices simplify closed-loop design because they do not require an external compensation network for common gain configurations. The LM258 family is therefore useful when designers need stable voltage gain with fewer external components. The principal published characteristics include a large DC voltage gain of 100 dB, a unity-gain bandwidth of 1.1 MHz, and low input bias current of 20 nA. Its low-power architecture provides very low supply current per amplifier, essentially independent of supply voltage according to the manufacturer datasheet. The two independent amplifier channels can implement separate gain stages, buffers, comparators, or active-filter sections within one package. The internally compensated architecture provides stable operation in voltage-follower and non-inverting configurations. A 1.1 MHz unity-gain bandwidth makes the device suitable for audio-frequency signal conditioning, sensor interfaces, and low-frequency control loops. Input bias current of 20 nA helps limit bias-current error when the source impedance is high, while the 0.6 V/us slew rate supports changing waveforms without excessive distortion. Typical uses include audio preamplification, low-voltage sensor conditioning, active filtering, industrial instrumentation, and general-purpose buffering. Because the package contains two amplifiers, it can reduce board area where two independent analog functions are required. Common-mode range, output swing, supply limits, input offset voltage, and exact channel behavior must be checked against the manufacturer datasheet before final circuit release. Design the PCB with short feedback paths, stable reference connections, and decoupling capacitors placed close to the supply pins. Confirm output swing and input common-mode limits for the selected supply voltage. Verify noise, offset, and stability requirements with the closed-loop gain and source impedance used in the finished circuit. This page combines the published LM258YDT characteristics with package details, application guidance, comparison information, and drop-in replacement considerations. It is designed to help engineers identify whether the LM258YDT matches a dual-amplifier requirement before moving to detailed schematic review and qualification.

RFC Hubungi kami
LM258YPT - Dual Low-Power Op Amp | STMicroelectronics
LM258YPT

LM258YPT - Dual Low-Power Op Amp | STMicroelectronics

The STMicroelectronics LM258YPT is a low-power dual operational amplifier consisting of two independent, high-gain, internally frequency-compensated amplifiers in an 8-pin TSSOP package. According to the manufacturer product page, the device is designed for single-supply operation over a wide voltage range, while the distributor listing identifies a 100 dB gain specification and 1.1 MHz bandwidth. Each amplifier includes low-input-bias-current characteristics suited to feedback, sensing, and signal-conditioning circuits. An operational amplifier is a high-gain analog building block that compares two input voltages and drives its output toward the difference between them. The LM258 belongs to the dual operational-amplifier family within the broader linear IC and amplifier hierarchy. Internally frequency compensation simplifies closed-loop use because designers do not need to add an external dominant-pole capacitor for ordinary stable operation. The LM258YPT provides two amplifiers in one compact surface-mount package. Its 100 dB gain and 1.1 MHz bandwidth make it appropriate for audio-frequency signal paths, transducer conditioning, feedback networks, and low-frequency control applications. Low input bias current helps preserve measurement accuracy when the source impedance is relatively high, while the dual configuration saves board area compared with two separate single amplifiers. Each channel is independent, allowing one section to perform amplification while the other handles a different signal or a supervisory function. Because the amplifiers can operate from a single supply, the output range remains constrained by the supply rails. Designers must account for this limitation in rail-to-rail sensing applications or add suitable biasing when signals extend below the lower supply voltage. Typical uses include audio preamplification, temperature-sensor interfaces, light-control loops, low-level instrumentation, and general feedback-control systems. The 8-pin TSSOP package is useful for compact industrial, instrumentation, and embedded-control designs where two amplifiers are required but a through-hole dual operational amplifier would be unnecessarily large. Layout should keep feedback components close to the relevant input and output pins, maintain a continuous ground reference, and place decoupling capacitance near the supply pins. Input and output nodes should remain short to reduce parasitic pickup. Designers should also verify common-mode range, output swing, slew rate, supply voltage, stability, and load behavior against the manufacturer datasheet before finalizing the circuit. This product page combines manufacturer-device identification, distributor availability information, pinout and datasheet references, application guidance, and qualified same-package alternatives. It is structured to help engineers compare the LM258YPT against other 8-pin dual operational amplifiers without treating every functionally similar device as a true drop-in replacement.

RFC Hubungi kami
LM2876TF - 40W Mono Class AB Amplifier | Texas Instruments
LM2876TF

LM2876TF - 40W Mono Class AB Amplifier | Texas Instruments

Texas Instruments LM2876TF is a high-performance 40 W mono Class AB audio power amplifier with mute, specified to deliver continuous average output power into an 8 ohm load from a 20 V to 60 V supply. The device is packaged in an 11-pin TO-220 isolated package. Its stated audio performance includes 0.1% total harmonic distortion plus noise from 20 Hz to 20 kHz under the manufacturer’s stated test conditions. An audio power amplifier is an integrated circuit that increases the voltage and current capability of an audio signal so it can drive a loudspeaker, subwoofer, or other high-impedance acoustic load. The LM2876 belongs to the amplifier IC hierarchy, where Class AB describes the output-stage operating method: the amplifier conducts during both halves of the audio waveform while minimizing crossover distortion. It also provides SPiKe protection, described by Texas Instruments as dynamically protecting the device against instantaneous thermal peaks. The principal specifications are 40 W continuous average output power, operation from 20 V to 60 V, and compatibility with an 8 ohm load. The LM2876 is a mono design intended for single-channel audio amplification. Its 0.1% THD+N rating covers 20 Hz to 20 kHz, providing a defined distortion and bandwidth reference when comparing it with other high-power audio amplifiers. Internally, the LM2876 combines Class AB output operation with a mute function and SPiKe thermal protection. The protection system is intended to react to instantaneous power events more effectively than a basic thermal shutdown alone. The isolated TO-220-11 construction supports conventional through-hole assembly and provides a mechanically robust option for audio equipment where heatsinking and grounding layout are important. Typical uses include monoblock subwoofer amplifiers, powered speaker systems, hi-fi amplifier output stages, home-theater audio power amplifiers, and industrial audio drivers. In each case, the amplifier requires a stable high-voltage supply, appropriate output filtering for the selected load, adequate copper area and thermal management, and careful separation of input, output, and power-ground paths. Design should begin with the 40 W continuous-power target rather than the absolute device rating. A practical implementation must provide enough supply headroom, verify thermal conditions at the selected load impedance, and account for the difference between continuous music power and short-duration peaks. The mute and SPiKe features add control and protection functions, but successful operation still depends on correct board layout and thermal design. This page combines the manufacturer’s core LM2876 specifications with purchasing guidance, application-focused engineering guidance, and a packaging-aware replacement assessment. It is intended to help designers determine whether the LM2876TF suits a high-power mono audio stage and how to verify board-level thermal, electrical, and sourcing requirements before committing to a design.

RFC Hubungi kami
LM2893M - 4.8 kBaud FSK Power-Line Transceiver | Texas Instruments
LM2893M

LM2893M - 4.8 kBaud FSK Power-Line Transceiver | Texas Instruments

The Texas Instruments LM2893M is a carrier-current transceiver integrated circuit for half-duplex serial data communication over existing power lines. It combines an FSK transmitter, a receiver with phase-locked-loop demodulation, and an interface to the carrier-current network in a 20-terminal SOP package. The verified device supports data rates up to 4.8 kBaud and an operating temperature range of -40°C to +85°C. A carrier-current transceiver is a communications interface that superimposes a modulated signal onto an electrical power or communication line. In the broader electronics hierarchy, this device belongs to the interface-IC category rather than a general-purpose data converter. The LM2893M is designed to communicate short serial messages between remotely distributed nodes without requiring a dedicated signal pair, making it useful for energy-management equipment, home-automation controllers, appliance control, and industrial systems that already share a mains-powered network. The principal verified features include FSK modulation, phase-locked-loop demodulation, half-duplex bidirectional operation, a maximum data rate of 4.8 kBaud, operation from an 18 V supply, and a -40°C to +85°C industrial temperature range. Its 20-terminal gull-wing SOP package has a 1.27 mm terminal pitch according to the verified distributor listing. Because carrier-current communication is sensitive to network loading, coupling method, attenuation, noise, and grounding, successful implementation requires the interface network and filtering to be evaluated with the intended power-line environment. The LM2893M is most appropriate when both ends of a link can share a power or utility line and low data throughput is sufficient. The 4.8 kBaud rate suits status reporting, control commands, meter-reading messages, and energy-management telemetry rather than streaming data. Half-duplex operation requires the controller to avoid simultaneous transmission and to manage turnaround timing, while the PLL-based receiver provides the demodulation function required to recover FSK information from the carrier waveform. Designers should provide suitable supply bypassing and define the line-coupling, protection, filtering, and grounding arrangement with the actual mains network. Regulatory, safety, and isolation requirements must be handled by the complete interface circuit rather than assumed to be satisfied by the IC. The LM2893M itself is not a mains-isolated network interface, and its operating voltage should not be confused with the voltage appearing on the coupled power line. This page combines verified pricing, package information, operating limits, interface characteristics, and application guidance with the available manufacturer-family relationship. It also documents the absence of verified drop-in equivalents instead of presenting unverified substitutes as production-ready replacements.

RFC Hubungi kami
LM2893MX - 20-Pin Carrier-Current Transceiver | Texas Instruments
LM2893MX

LM2893MX - 20-Pin Carrier-Current Transceiver | Texas Instruments

The Texas Instruments LM2893MX is a carrier-current transceiver designed for half-duplex, bidirectional serial communication over power-line or carrier-current networks. The device operates from a nominal 18 V supply, supports 13 V to 24 V and 14 V to 30 V operating ranges, and draws up to 79 mA. It is packaged in a 20-pin SOIC with a 1.27 mm terminal pitch, gull-wing leads, and an industrial temperature range of -40°C to +85°C. A carrier-current transceiver is an interface circuit that couples serial data onto and receives data from an electrical distribution or communication line. Carrier-current systems use an existing power or telephone conductor as the physical transmission medium, allowing equipment located at separate points to exchange information without a dedicated data cable. This places the LM2893MX within the broader hierarchy of communication interface IC, transceiver, line-interface circuit, and semiconductor. The LM2893MX is identified as a telecom interface transceiver and a general-purpose carrier-current interface. Its half-duplex operation supports two-way communication over the same line path, while the 79 mA maximum supply current provides a defined operating limit for power-supply design. The SOIC-20 package supports conventional surface-mount assembly and is suitable for equipment operating across the full -40°C to +85°C industrial temperature range. Carrier-current interfaces depend on accurate line coupling, controlled transmitter behavior, and receiver discrimination between wanted signals and line noise. The LM2893MX integrates the functional interface required for bidirectional serial bit-stream communication at the physical layer. System designers still need to account for line impedance, coupling components, termination, filtering, grounding, and protection networks when constructing a production interface. Typical applications include power-line data links, industrial equipment monitoring, remote telemetry, building automation, carrier-based communication equipment, and telecommunication networks that use existing conductors as communication media. The operating voltage and industrial temperature range make the device relevant to sustained industrial deployments where the interface must tolerate temperature variation and operate from a nominal 18 V supply. Design the LM2893MX around the electrical characteristics of the carrier line rather than treating it as a conventional point-to-point logic interface. External components must be selected for the line voltage, impedance, baud rate, isolation requirements, and transient environment, while the PCB layout should minimize noise coupling between the transmit and receive paths. Confirm the exact pin functions and recommended application circuit in the Texas Instruments datasheet before finalizing a new layout. This product page combines the LM2893MX electrical, package, environmental, and application information with practical PCB and implementation guidance. It also distinguishes the verified device characteristics from parameters that must be confirmed during design-in, helping engineers evaluate the part efficiently while retaining control over circuit-level requirements.

RFC Hubungi kami
LM2893N - Carrier-Current Transceiver | National Semiconductor
LM2893N

LM2893N - Carrier-Current Transceiver | National Semiconductor

National Semiconductor LM2893N is a one-transceiver carrier-current interface IC designed for half-duplex, bidirectional serial communication over an existing power-mains network. The device is offered in a 20-pin PDIP package and combines a transmitter and receiver in one integrated circuit. Carrier-current systems use power-line infrastructure to transfer information between remotely separated locations rather than requiring a separate communication cable. A carrier-current transceiver is a type of power-line interface IC. Carrier-current communication belongs to the broader power-line networking and interface IC hierarchy, where communication signals are superimposed on an electrical power conductor. The LM2893N is intended to interface a serial data source with a carrier-current network, making it useful where the mains wiring already extends between remote nodes and adding a separate low-speed communication route would be impractical. The verified source information identifies the LM2893N as a one-transceiver, 20-PDIP device for carrier-current systems. Its principal benefit is integration: both directions of the half-duplex link are handled by a single package instead of separate transmitter and receiver packages. The confirmed communication mode is bidirectional and serial, allowing a node to exchange bit-stream data with another node over the same carrier-current medium. The LM2893N belongs to the bipolar LM1893/LM2893 carrier-current transceiver family. This family positioning indicates that the LM2893 is the higher-temperature-oriented member relative to the LM1893 designation, although exact electrical limits and comparison values are not included in the supplied distributor data. Designers should use the manufacturer datasheet for voltage ratings, current limits, logic thresholds, transmission timing, receiver sensitivity, and network-interface details before releasing production hardware. Typical carrier-current uses include remote metering, building-management communication, industrial monitoring, appliance control, and low-speed supervisory links where power and data share the same wiring. In these systems, the LM2893N acts as the physical-layer interface between the communication network and the node's serial logic. Network loading, isolation requirements, coupling method, transmit power, and protocol timing remain application-specific. The principal design consideration is that carrier-current communication is materially different from ordinary RS-485 or isolated digital communication. The power conductor presents a difficult noise environment, and the interface network must be characterized for attenuation, impedance, coupling, and surge exposure. PCB grounding, filtering, isolation boundaries, and protection components therefore deserve attention before the communication protocol is finalized. This product page combines verified distributor identification, family-level technical context, package information, sourcing links, and structured engineering guidance that is not available in a basic distributor listing. Exact electrical specifications and qualified drop-in replacements remain explicitly separated from verified facts so engineers can make a safe replacement decision without relying on assumptions.

RFC Hubungi kami
LM2900D - Quad Norton Operational Amplifier | Texas Instruments
LM2900D

LM2900D - Quad Norton Operational Amplifier | Texas Instruments

The Texas Instruments LM2900D is a quad, high-gain, frequency-compensated Norton operational amplifier in a 14-pin SOIC (D) package. The device contains four independent amplifier sections designed for single-supply or split-supply operation over a wide supply-voltage range. Its Norton input stage provides low input bias current, while the internally compensated architecture simplifies gain-stage implementation in general-purpose signal conditioning. The LM2900D is identified by the verified distributor listing as a standard general-purpose amplifier with four circuits in a 14-SOIC package. A Norton operational amplifier is a current-buffer input operational-amplifier architecture. It differs from the more common voltage-input differential pair by using a translinear input stage that offers low input bias current and good performance with high-impedance sources. This places the LM2900D in the operational-amplifier hierarchy: operational amplifier, amplifier IC, analog IC, and semiconductor. The part is intended for general-purpose analog signal conditioning rather than precision instrumentation or automotive-qualified systems. According to the Texas Instruments LM2900 product page, the LM2900 family consists of four independent, high-gain frequency-compensated Norton operational amplifiers designed to operate from a single supply over a wide range of voltages. The product description also identifies large output-voltage swing, output short-circuit protection, internal frequency compensation, and low input bias current as important characteristics. These features make the device suitable for buffering, voltage amplification, signal conditioning, and general feedback-control circuits. The LM2900D can be used with a single positive supply or with split supplies. In single-supply designs, the input and output signal levels must remain within the amplifier's common-mode and output-swing limits. The LM2900 family is internally frequency compensated, so the feedback network establishes the closed-loop gain without requiring a separate compensation capacitor in ordinary applications. The 14-pin SOIC package provides a conventional surface-mount footprint and a practical temperature range for industrial and consumer equipment. Typical uses include transducer-signal conditioning, sensor interfaces, audio preamplification, low-current feedback amplifiers, and general analog control loops. Because the verified data does not provide detailed electrical limits, bandwidth, noise, slew rate, or exact input/output range, those parameters should be confirmed in the manufacturer datasheet before final design release. The verified distributor listings show current purchasing channels, but they do not provide a reliable standardized price table in the supplied data. This page combines the verified manufacturer and distributor identity for LM2900D with package information, sourcing links, comparison structure, and practical selection guidance. It is intended to help engineers identify the correct 14-SOIC Norton amplifier while avoiding unsupported parameter assumptions. Confirm the latest ordering information, electrical limits, lead time, and lifecycle status with Texas Instruments or an authorized distributor before production commitment.

RFC Hubungi kami