STMicroelectronics

LM258WYPT - Dual 30V Low-Power Op Amp | STMicroelectronics

MPN: LM258WYPT ✓ Aktif
30 V Vdss 20 nA Id TSSOP-8 Package Internal Speed
MOQ: 1 |

LM258WYPT Ringkasan

STMicroelectronics LM258WYPT is a dual, internally frequency-compensated operational amplifier designed for low-power single-supply operation. The device provides two independent amplifiers, a 30 V maximum supply rating, approximately 1.1 MHz gain-bandwidth product, 0.6 V/µs slew rate, 85 dB open-loop gain, and 2 mV input offset voltage. It is packaged for surface-mount assembly in an 8-pin TSSOP tape-and-reel format.

A low-power dual operational amplifier is an analog signal-conditioning IC that provides voltage gain while remaining usable from a single positive supply. In the product hierarchy, the LM258 belongs to operational amplifiers, analog amplifiers, analog signal-processing ICs, and broader semiconductor components. Its internally compensated architecture simplifies design because each amplifier does not require an external compensation network for ordinary closed-loop operation.

The LM258WYPT emphasizes low supply current, approximately 700 µA, with a supply drain that remains largely independent of supply magnitude. Its 20 nA input bias current suits many high-impedance sensing paths, while the 1.1 MHz gain-bandwidth product supports general-purpose signal conditioning at low frequencies. The two amplifiers are independent, allowing simultaneous channel processing or use in unrelated circuit blocks.

Internally frequency compensation stabilizes operation in common feedback configurations. The 600 V/µs slew rate provides useful response for audio, transducer, and industrial control signals, although the device is not optimized for high-speed precision applications. The 85 dB open-loop gain and 2 mV offset specification define its practical precision in feedback-based amplifier stages.

Typical uses include low-frequency sensor amplification, audio preamplification, bridge-amplifier signal conditioning, current-loop interfaces, and general industrial control. The 30 V supply capability also permits operation from higher-voltage rails when the signal amplitude remains within the amplifier's input and output limits. Independent amplifiers make the device useful in dual-channel transducers and compact analog front ends.

Designers should verify common-mode and output-swing limits against the selected supply voltage, provide suitable bypassing near the power pins, and account for input bias current when working with high-source-impedance sensors. Stable feedback layout, short output paths, and clean grounding remain important because PCB leakage and leakage current can disturb sensitive measurements even when the amplifier itself performs correctly.

This page combines package, electrical, application, sourcing, and replacement information into an engineering-focused guide. It also distinguishes the exact LM258WYPT order code from related LM258 variants whose temperature grade, offset bin, package, or tape-and-reel suffix can differ.

Pilihan pengganti yang segera untuk LM258WYPT — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

LM258AWYPT

✅ Masuk Drop-In
📦 TSSOP-8
Tighter input-offset bin; gain-bandwidth product remains 1.1 MHz and slew rate remains approximately 0.6 V/µs

📋 Alternatif rujukan (tidak dalam katalog)

LM258WYPT Penilaian maksimum & Ciri-ciri Elektrik

Amplifier Type Dual general-purpose operational amplifier
Number of Circuits 2 circuits
Maximum Supply Voltage 30 V
Gain-Bandwidth Product 1.1 MHz
Slew Rate 0.6 V/µs
Open-Loop Gain 85 dB
Input Offset Voltage 2 mV
Input Bias Current 20 nA
Arus Pemberi Arus 700 µA
Output Current 40 mA
Frequency Compensation Internal
Supply Type Single or split supply
Kemasan TSSOP-8
Jenis Pemasangan Surface mount
Packaging Form Tape and reel
Status RoHS Compliant

Panduan Konfigurasi Pin LM258WYPT tssop-8

Konfigurasi pin untuk LM258WYPT (tssop-8 pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.

Garis bentuk pengecah pakai tssop-8 untuk LM258WYPT

Tiada data garisan pin yang diperoleh untuk LM258WYPT.

Rujuk kepada lembaran data untuk konfigurasi pin penuh.

Aplikasi Biasa

LM258WYPT patut untuk 6 aplikasis: Low-Frequency Transducer Buffering, Audio Preamplification, Current-to-Voltage Signal Conversion, Industrial Bridge-Sensor Amplification, Power-Supply Feedback and Monitoring, Temperature and Pressure Sensor Interfaces.

🏭

Low-Frequency Transducer Buffering

The LM258WYPT suits low-frequency sensor buffers because its two independent channels can condition two measurement inputs while drawing approximately 700 µA of supply current. The 20 nA input bias current reduces loading from high-impedance sources, and the 85 dB open-loop gain supports practical closed-loop gain stages. Each internally compensated amplifier simplifies implementation around resistive feedback networks. The principal design constraint is the input common-mode range: sensor output voltage must remain inside the amplifier’s valid range for the selected supply. A 30 V maximum supply rating provides flexibility for industrial systems, although protection, guarding, and leakage control remain necessary around high-impedance transducers.

🎧

Audio Preamplification

The LM258WYPT can provide two channels of general-purpose audio preamplification when compactness and low supply current are priorities. Its 1.1 MHz gain-bandwidth product covers the audible range with additional bandwidth margin, while the 0.6 V/µs slew rate handles moderate signal excursions. The dual, independent architecture supports stereo or dual-mono signal conditioning without sharing an input or output. Designers should keep the signal within the output-swing limits, use stable feedback ratios, and bypass the supply pins locally. The 2 mV input offset is generally acceptable for audio, but it is not appropriate when a precision reference or instrumentation-amplifier error budget requires sub-millivolt accuracy.

⚡

Current-to-Voltage Signal Conversion

A feedback transimpedance stage can use one LM258WYPT channel for sensor-current conversion and the second channel for gain or filtering. The approximately 20 nA input bias current is favorable for moderate source impedances, and the 85 dB open-loop gain helps preserve loop gain in a feedback configuration. With a 1.1 MHz gain-bandwidth product, the amplifier supports bandwidths appropriate for many slow sensor and industrial-control signals. Practical performance depends on feedback-resistor selection, input capacitance, board leakage, and output-swing margin. Check the resulting noise gain and stability across the required signal range rather than assuming the amplifier’s nominal bandwidth alone determines the usable response.

🏭

Industrial Bridge-Sensor Amplification

The LM258WYPT’s two independent amplifiers are convenient for differential bridge-sensor front ends when one channel handles excitation-side buffering or filtering and the other processes the bridge output. Its 30 V maximum supply rating supports higher-voltage industrial control rails, while approximately 700 µA supply current keeps the amplifier suitable for distributed, low-power instrumentation. The 2 mV offset and 20 nA bias current must be included in the system error budget, particularly for resistive bridges with high source impedance. PCB routing should preserve signal symmetry, maintain clean grounding, and minimize leakage between high-impedance input nodes and nearby supply or digital traces.

🔧

Power-Supply Feedback and Monitoring

The LM258WYPT can monitor a regulated rail and amplify the difference between a feedback voltage and a reference, making its two channels useful for supervisory or fault-detection functions. The wide 30 V supply capability permits operation around higher-voltage industrial rails, provided the input common-mode and output-swing requirements are respected. Its 700 µA supply consumption is useful when every milliampere affects standby power. Because this is a general-purpose amplifier rather than a dedicated supervisor, threshold accuracy, fault-response time, and reference quality depend on the external network. Keep feedback traces short, isolate the amplifier from noisy switching nodes, and ensure stable operation under transient loading.

💊

Temperature and Pressure Sensor Interfaces

The LM258WYPT is appropriate for slow temperature and pressure sensors whose outputs fall within the common-mode range of the selected supply. Two independent channels can handle complementary sensor signals or provide buffering for a resistance-based bridge. The amplifier’s 20 nA input bias current reduces error with moderately high sensor impedances, while its 1.1 MHz bandwidth is more than adequate for many thermal and mechanical measurement systems. Offset error, drift, sensor excitation noise, and resistor tolerances will usually dominate the overall accuracy. Use guarded input layouts, clean reference connections, and local supply bypassing to obtain repeatable low-level measurements.

What are the key specifications of LM258WYPT that engineers should know?
The LM258WYPT is a dual, internally compensated operational amplifier with a 30 V maximum supply voltage, 1.1 MHz gain-bandwidth product, 0.6 V/µs slew rate, 85 dB open-loop gain, and approximately 700 µA supply current. According to the manufacturer datasheet, each amplifier has a 2 mV input offset specification and 20 nA input bias current. The device uses an 8-pin TSSOP package and contains two independent amplifier channels.
Where can I download the LM258WYPT datasheet PDF?
The LM258WYPT datasheet PDF is available from the manufacturer-document links on this page and describes the dual low-power operational-amplifier family. The document identifies the two independent, internally frequency-compensated channels, their single-supply operation, and application areas including transducer interfaces. Use the pin-description table when assigning the eight TSSOP terminals and the electrical-characteristics tables for design limits.
Where can I find the LM258WYPT pinout and package information?
The LM258WYPT uses an 8-pin TSSOP surface-mount package supplied on tape and reel. The manufacturer datasheet contains the authoritative connection diagram and pin descriptions for both amplifier channels, including supply and output terminals. Because this page does not reproduce the terminal-by-terminal diagram, use the datasheet before finalizing PCB tracks, particularly for exposed thermal and decoupling requirements.
Can LM258WYPT operate from a single 5 V supply?
The LM258WYPT is designed for single-supply operation, and its supply drain is largely independent of the supply-voltage magnitude. A 5 V operating rail is therefore a normal use case, subject to the datasheet limits for input common-mode voltage and output swing. The device's approximately 700 µA supply current also makes it suitable for low-power analog signal-conditioning circuits.
When should I choose LM258WYPT over a precision operational amplifier?
Choose the LM258WYPT when a low-cost, low-power dual amplifier with wide supply tolerance is more important than very low offset, low input bias current, or rail-to-rail output swing. Its 2 mV input offset, 85 dB open-loop gain, 1.1 MHz bandwidth, and two independent channels suit general-purpose industrial, audio, and transducer circuits. A precision amplifier is preferable when offset drift and input error directly limit measurement accuracy.
What is the difference between LM258WYPT and LM258AWYPT?
Both are 8-TSSOP dual operational amplifiers with a 1.1 MHz gain-bandwidth product and approximately 0.6 V/µs slew rate, but the AW ordering code identifies a tighter input-offset bin. The LM258AWYPT is therefore the better candidate when offset-bin selection matters, while LM258WYPT may be preferable where that distinction is unnecessary. Confirm temperature grade, offset limits, and marking requirements against the manufacturer datasheet.
Is LM258WYPT suitable for industrial sensor conditioning?
The LM258WYPT is suitable for many low-frequency industrial sensor-amplifier stages because it combines two independent channels, a 30 V supply rating, approximately 700 µA supply current, and 20 nA input bias current. The amplifier can support transducer buffering, gain stages, and low-frequency feedback networks. High-impedance sensors still require careful leakage, guarding, grounding, and input common-mode checks.
What can replace an LM258WYPT in an 8-pin TSSOP design?
The closest identified 8-TSSOP replacement is STMicroelectronics LM258AWYPT, which uses the same package and retains the same 1.1 MHz gain-bandwidth product and approximately 0.6 V/µs slew rate while providing a tighter offset bin. Confirm the complete pinout and every electrical limit before substitution. A request through the Request a Quote form on this page can help identify available sourcing options.
Is LM258WYPT the same as LM358PT?
The LM258WYPT and LM358PT are related general-purpose dual operational amplifiers, but they are not automatically interchangeable. The LM258WYPT has a 30 V maximum supply rating and approximately 1.1 MHz bandwidth, while the LM358PT must be checked separately for supply voltage, offset, bias current, common-mode range, and package details. Compare the manufacturer datasheets before treating either part as a drop-in replacement.
How much current does LM258WYPT consume?
The LM258WYPT consumes approximately 700 µA of supply current under the manufacturer datasheet conditions. Its low-power drain is described as largely independent of supply-voltage magnitude, making the amplifier suitable for single-supply and higher-voltage rail operation. Actual board consumption also includes load current and any external bias or feedback-network current.
What is the best Texas Instruments equivalent for LM258WYPT?
Texas Instruments offers the LM258 family as a potential functional alternative, but the exact package, pin arrangement, electrical limits, and ordering suffix must be verified before it can replace an LM258WYPT on the same PCB. The Texas Instruments LM258 product page identifies the family and its drop-in positioning, yet package-specific qualification remains essential. Do not substitute a different suffix without checking the manufacturer pinout and electrical tables.
Where can I buy LM258WYPT and check its lead time?
Use the Request a Quote form on this page to ask about LM258WYPT availability, lead time, order quantity, and shipment requirements. The exact order code is a dual operational amplifier in 8-pin TSSOP tape-and-reel packaging. Quote specialists can confirm whether the required quantity and date are supported before an order is placed.
What is the price of LM258WYPT?
Use the Request a Quote form on this page for the current unit price, quantity breaks, stock position, and lead time for LM258WYPT. Pricing and availability can vary with order quantity, shipment destination, and market conditions, so a current quotation provides more useful purchasing information than a static listing figure. The requested MPN must remain LM258WYPT to preserve the 8-pin TSSOP configuration.
Is LM258WYPT in stock?
Current inventory should be confirmed through the Request a Quote form on this page for the exact LM258WYPT order code. The part is offered as an 8-TSSOP tape-and-reel device, and at least one marketplace listing identifies an in-stock position. Inventory can change rapidly, so request the quantity and required delivery date with the quotation.
Does LM258WYPT need external frequency compensation?
No external frequency-compensation network is normally required because the LM258WYPT amplifiers are internally frequency compensated. The manufacturer describes both channels as high-gain operational amplifiers using internal compensation and intended for straightforward closed-loop use. Layout, stable feedback ratios, output loading, and application-specific stability checks remain necessary even when an external compensation capacitor is unnecessary.

Data referensi kejuruteraan untuk LM258WYPT — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose LM258WYPT for general-purpose dual amplification when a 30 V-rated, low-power amplifier is sufficient and the standard input-offset bin meets the accuracy requirement. Its 1.1 MHz bandwidth, 0.6 V/µs slew rate, 85 dB open-loop gain, and approximately 700 µA supply current fit slow sensor, audio, feedback, and industrial control circuits. Choose LM258AWYPT when the same TSSOP footprint and core performance are wanted but a tighter input-offset bin is preferable. Neither device should be selected blindly for high-precision measurement, because the 2 mV offset and non-rail-to-rail behavior can dominate a demanding error budget. Before substituting a different manufacturer’s dual amplifier, verify the complete pinout, common-mode range, output swing, compensation method, temperature grade, and electrical limits. A redesign may be preferable when rail-to-rail input or output operation, lower offset, lower bias current, or higher bandwidth is required.

Perbandingan dengan Gantian

Parametr Produk Ini LM258AWYPT
Package TSSOP-8 TSSOP-8
Brand STMicroelectronics STMicroelectronics
Amplifier Configuration Dual Dual
Maximum Supply Voltage 30 V 30 V
Gain-Bandwidth Product 1.1 MHz 1.1 MHz
Slew Rate 0.6 V/µs 0.6 V/µs
Input Offset Voltage 2 mV Tighter offset bin
Input Bias Current 20 nA 20 nA
Supply Current 700 µA 700 µA
Open-Loop Gain 85 dB 85 dB
Output Current 40 mA 40 mA
Internal Frequency Compensation Yes Yes

Penyeberangsung Jelas

  • Retains the standard LM258 performance envelope (vsLM258AWYPT)
  • Uses the standard offset-voltage bin (vsLM258AWYPT)
  • Combines two independent low-power channels (vsLM258AWYPT)

Catatan Desain

Place the input, output, and feedback components close to the LM258WYPT pins, particularly the power terminals. Keep each amplifier’s feedback loop compact and route high-impedance input nodes away from switching nodes and noisy digital traces. Because the amplifier can be used with two independent channels, preserve channel separation in the layout and provide a common, low-impedance ground reference. Use the manufacturer pin-description table when defining land patterns and keepout requirements.

Confirm input common-mode voltage and output-swing limits for the actual supply voltage before finalizing the feedback network. A nominal 30 V maximum supply rating does not imply that the amplifier can process signals across the entire input range on every supply. Add local bypass capacitance at the supply pins and route it through a short, low-inductance path. For battery-powered circuits, include the approximately 700 µA device current as well as load and divider currents in the standby-power budget.

Use the 1.1 MHz gain-bandwidth product and 0.6 V/µs slew rate as design limits rather than guaranteed final-stage bandwidth. Check the required signal frequency, closed-loop noise gain, output loading, and resulting stability margin. High-impedance sensor nodes should be guarded against PCB contamination and leakage. If the application includes a large feedback resistor, verify bias-current error, input capacitance, and settling behavior across the intended signal range.

Maklumat Kesediaan

RoHS
Compliant
REACH
Unknown
AEC-Q100
Unknown
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

RoHS compliance is identified in the product listing. Other compliance attributes require confirmation from the manufacturer’s order-code or quality documentation.

Pencarian Berhubungan

LM258WYPT LM258WYPT datasheet LM258WYPT datasheet pdf LM258WYPT pinout LM258WYPT TSSOP-8 STMicroelectronics LM258WYPT LM258WYPT equivalent LM258WYPT replacement LM258WYPT vs LM258AWYPT LM258WYPT price LM258WYPT stock LM258WYPT dual op amp LM258WYPT sensor amplifier LM258WYPT schematic

Komponen dan Tanda berkaitan

STMicroelectronics LM258WYPT LM258AWYPT LM258 LM358 dual operational amplifier low-power operational amplifier analog amplifier signal-conditioning IC single-supply operation internally frequency-compensated amplifier gain-bandwidth product slew rate input offset voltage input bias current open-loop gain common-mode voltage TSSOP-8 TSSOP package family surface-mount technology transducer interface audio preamplifier bridge sensor RoHS
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ