Produk (44,000+)

LM2902YPT - Low-Power Quad Op Amp, 1.3 MHz | STMicroelectronics
LM2902YPT

LM2902YPT - Low-Power Quad Op Amp, 1.3 MHz | STMicroelectronics

The STMicroelectronics LM2902YPT is a low-power, general-purpose quad operational amplifier containing four independent, internally frequency-compensated amplifiers in a 14-pin TSSOP package. Each amplifier features a 1.3 MHz gain-bandwidth product, 0.4 V/µs slew rate, low 20 nA input bias current, and a typical input offset voltage of 7 mV. The device is designed for automotive and industrial control systems operating from a single supply or split supplies. An operational amplifier is an analog signal-processing building block that compares its inverting and non-inverting inputs and drives its output toward the higher input potential. Within the broader hierarchy, a quad operational amplifier contains four amplifiers in one package, reducing board area and simplifying multi-channel instrumentation, sensor, and feedback-control designs. The LM2902 family combines internal frequency compensation with low power consumption, making it suitable for general-purpose signal conditioning rather than precision or high-speed applications. Key characteristics include push-pull output capability, low input bias current, and input common-mode operation that allows the inputs to approach the supply rails. The four amplifiers share supply pins but remain electrically independent, allowing simultaneous use for sensing, amplification, filtering, and actuator drive. Because all four channels operate from the same package and supply network, common power-supply bypassing and thermal management serve all channels at once. The internally compensated architecture makes the LM2902 stable in the voltage-follower configuration without external compensation networks. Its 1.3 MHz bandwidth is adequate for audio-frequency, industrial-control, and general feedback loops, while the 0.4 V/µs slew rate limits large-signal response. Applications include transducer interfaces, low-level sensor amplification, motor-feedback networks, audio preamplification, and multi-channel control systems. Designers should keep input and output pins within the common-mode and output-swing limits shown in the manufacturer datasheet. Place the supply bypass capacitor close to the device, maintain short feedback paths, and avoid driving capacitive loads without isolation. The quad package reduces component count, but all four channels share the package thermal path. This page combines manufacturer specifications, application guidance, package details, and drop-in replacement analysis to support faster component selection and PCB design for automotive and industrial control systems.

RFC Hubungi kami
LM2903AM8-13 - Dual Comparator, A-Grade 1mV | Diodes Inc
LM2903AM8-13

LM2903AM8-13 - Dual Comparator, A-Grade 1mV | Diodes Inc

The Diodes Incorporated LM2903AM8-13 is an A-grade dual differential voltage comparator with a low input offset voltage of 1 mV (A device), housed in an 8-MSOP surface-mount package. It belongs to the LM2901/LM2903 family of dual and quad precision comparators with open-collector, rail-to-rail output stages. A voltage comparator is an analog IC that compares two input voltages and drives its output to indicate which input is higher. Comparators form the bridge between the analog front end and digital logic: they are classified within the linear IC family, sitting alongside amplifiers and voltage references in the signal-chain hierarchy, and are foundational building blocks of power management, sensing, and monitoring subsystems. Key features include a common-mode input voltage range that includes ground, enabling single-supply operation from ground-referenced sensors; a differential input voltage range equal to the power supply voltage, which protects the device during fault conditions; and a low output saturation voltage of 200 mV at 4 mA sink current. The output is compatible with TTL, MOS, and CMOS logic levels across a wide supply range. The open-collector output architecture allows wired-OR configurations and interfacing to logic rails above or below the comparator supply, provided the absolute maximum output voltage is respected. Input PNP transistors permit input voltages down to the negative rail, making ground-sense comparators, zero-crossing detectors, and current-sense threshold circuits straightforward on a single supply. Typical applications include over-voltage and under-voltage monitoring in industrial systems, battery-powered limit detection, oscillator and relaxation-clock circuits, window comparators in power supplies, and automotive sensor thresholding where the wide temperature grade matters. Design consideration: because the output is open-collector, always provide a pull-up resistor to the desired logic rail; the pull-up value sets sink current and switching speed. Small hysteresis (positive feedback of a few millivolts) is recommended in noisy environments to prevent output chatter near the threshold. This page adds value beyond the manufacturer datasheet by compiling verified drop-in alternatives, an 8-pin MSOP pinout map, parameter comparison tables, and practical engineering design notes in one place for faster sourcing and layout decisions.

RFC Hubungi kami
LM2903AQM8-13 - Dual 36V Automotive Comparator | Diodes
LM2903AQM8-13

LM2903AQM8-13 - Dual 36V Automotive Comparator | Diodes

Diodes Incorporated LM2903AQM8-13 is a dual differential analog comparator designed for automotive and industrial systems, with a 36 V maximum supply voltage, 1 mV input offset voltage for the A grade, and an 8-pin MSOP package. The device contains two independent open-collector comparators and supports single-supply or split-supply operation. Its open-collector outputs are compatible with TTL, MOS, and CMOS logic families. An analog comparator is a semiconductor that compares two input voltages and produces a digital logic state indicating which input is higher. The LM2903 belongs to the comparator hierarchy that includes general-purpose voltage comparators, differential comparators, interface ICs, and discrete semiconductors. This makes it suitable for threshold detection, signal conditioning, overvoltage monitoring, and control decisions where a simple logic output is required rather than an amplified analog voltage. The A-grade LM2903 provides a low 1 mV input offset voltage, helping reduce errors when two closely spaced voltages must be compared. Its low output saturation voltage is 200 mV at an output current of 4 mA. The open-collector architecture allows the output transistor to be pulled up to a suitable external voltage, and low input bias current of 25 nA reduces disturbance of high-impedance sensing circuits. The device is qualified to AEC-Q100 Grade 1 for automotive applications. The LM2903Q family operates from a single positive supply or from split supplies, with the common-mode input range including ground. Its differential input range can extend across the power-supply voltage. Two independent channels allow simultaneous or unrelated comparisons, while the common eight-pin MSOP footprint reduces board area compared with discrete single comparators. Output pull-up resistors must be added because the open-collector outputs do not source current actively. Typical uses include automotive battery monitoring, sensor threshold detection, overvoltage and undervoltage protection, window comparators, and industrial control interfaces. In an automotive application, the device can compare a divided battery or sensor voltage against a reference and produce a logic signal suitable for a controller or protection circuit. Its AEC-Q100 Grade 1 qualification is the principal automotive distinction from the non-automotive LM2903M8-13. When designing the circuit, account for input common-mode limits, output pull-up requirements, and the voltage difference that the input pair can withstand. Keep sensitive comparator inputs away from switching-current paths and provide a stable reference source when input offset directly affects the decision threshold. Decoupling capacitors should be placed close to the supply and ground pins according to the manufacturer's recommended application layout. This page combines the exact package and automotive qualifications, pin and family context, practical protection applications, and a same-package comparison with the non-automotive LM2903M8-13. It highlights where the A-grade offset specification and AEC-Q100 qualification justify selection, while also showing the limits of drop-in alternatives that differ in automotive qualification.

RFC Hubungi kami
LM2903AQTH-13 - 36V Dual Automotive Comparator | Diodes Incorporated
LM2903AQTH-13

LM2903AQTH-13 - 36V Dual Automotive Comparator | Diodes Incorporated

Diodes Incorporated LM2903AQTH-13 is a dual differential voltage comparator designed for general-purpose, automotive, and industrial signal-conditioning applications. The device provides two independent comparator channels, a 36 V maximum supply rating, 1 mV input offset voltage for the A-grade version, and an open-collector output architecture. It is packaged in an 8-pin TSSOP package, making it suitable for compact surface-mount designs where two independent comparison functions are required. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a digital logic state indicating which input is higher. The LM2903AQ family belongs to the broader comparator hierarchy, which includes differential comparators, analog interface ICs, and general-purpose semiconductor components. Its differential inputs and open-collector outputs are useful for threshold detection, sensor conditioning, overvoltage monitoring, and control systems. The LM2903AQTH-13 is specified as an automotive-compliant device in the LM2903Q/LM2903AQ family. The family is available in SO-8, MSOP-8, and TSSOP-8 packages for the dual comparator configuration and uses industry-standard pinouts. The A device has a 1 mV input offset-voltage specification, while the non-A device is specified at 2 mV. The input common-mode voltage range includes ground, and the differential input voltage range is equal to the power-supply voltage. Open-collector outputs require an external pull-up resistor to establish the positive logic level. These outputs are compatible with TTL, MOS, and CMOS logic levels, and the low output saturation voltage is 200 mV at 4 mA for the LM2903 family. The dual architecture allows one device to implement two comparator functions, reducing board area compared with separate single comparators. Typical applications include automotive battery and power-system monitoring, industrial control inputs, sensor threshold detection, overvoltage and undervoltage protection, and digital control systems. The TSSOP-8 package supports compact PCB layouts, while the broad supply-voltage capability supports systems operating from industrial rails. When using the device, account for input common-mode limits, output pull-up requirements, and the maximum differential input voltage when designing the surrounding analog front end.

RFC Hubungi kami
LM2903AS-13 - Dual 36V Comparator | Diodes Incorporated
LM2903AS-13

LM2903AS-13 - Dual 36V Comparator | Diodes Incorporated

Diodes Incorporated LM2903AS-13 is a dual differential voltage comparator rated for operation up to 36 V, with a typical input bias current of 25 nA and output current capability of 20 mA. The device is packaged in an 8-pin SOIC and provides two independent comparator channels for general-purpose signal conditioning, threshold detection, and industrial control applications. A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when the non-inverting input exceeds the inverting input. The LM2903 belongs to the comparator hierarchy, where a comparator is an interface IC used to translate small analog voltage differences into digital logic levels. Its two channels can compare independent sensor, reference, or feedback signals while sharing a common supply and ground. The principal electrical features include two independent channels, a 36 V maximum supply-voltage class, low 25 nA typical input bias current, and open-collector outputs capable of sinking 20 mA. The low input bias current reduces disturbance in high-impedance sensing circuits. The open-drain outputs also permit wired-AND behavior when multiple comparator outputs share a pull-up resistor, provided the design respects the voltage and current limits of each device. The LM2903 can operate from a single supply or from split positive and negative supplies, making it adaptable to legacy industrial and automotive-style signal chains. Because the comparators are independent, one channel can monitor an upper threshold while the other detects a lower threshold. Output-referenced behavior and input common-mode limits must still be checked against the application supply arrangement before the circuit is released. Typical uses include sensor threshold modules, overvoltage and undervoltage detection, window comparators, relay-driver interfaces, industrial control logic, and waveform crossing detection. The low input bias current is particularly useful when the input source has a high equivalent resistance or when the comparator must avoid loading a sensor output. A suitable pull-up resistor is required for each open-collector output when the output must drive a high logic state. The main design consideration is the relationship between supply voltage, input common-mode range, and output pull-up voltage. Keep the pull-up resistor high enough to limit channel current but low enough to achieve the required rise time. Check that the pull-up voltage remains within the output transistor rating and that parasitic PCB capacitance does not slow switching. The 8-pin SOIC footprint also requires adequate copper area and thermal clearance when operating at elevated ambient temperatures. This page combines device specifications, pin-level guidance, application-oriented design notes, and clearly qualified drop-in comparisons. It is intended to help engineers evaluate the LM2903AS-13 for PCB reuse, comparator selection, supply compatibility, and threshold-circuit implementation without replacing the need to review the manufacturer datasheet during sign-off.

RFC Hubungi kami
LM2903ATH-13 - Dual Differential Comparator, TSSOP-8 | Diodes Inc
LM2903ATH-13

LM2903ATH-13 - Dual Differential Comparator, TSSOP-8 | Diodes Inc

The Diodes Incorporated LM2903ATH-13 is a dual general-purpose differential voltage comparator supplied in an 8-pin TSSOP surface-mount package, rated for supply voltages up to ±18V (36V total), with two independent high-gain comparators in a single footprint. A voltage comparator is an analog circuit element that compares two input voltages and drives its output to indicate which is higher. Within the signal-chain hierarchy, the comparator sits alongside operational amplifiers as a member of the analog IC family: where an op-amp amplifies the difference, a comparator saturates its output to a logic-compatible level, making it a bridge between the analog and digital domains. The LM2903 family - originally introduced by multiple manufacturers and now offered by Diodes Incorporated as the LM2903 series - is the industry-reference dual comparator used worldwide. Key features of the LM2903ATH-13 include two independent comparators with high open-loop gain, a wide supply range spanning single or dual supplies up to ±18V/36V, low input offset characteristics, and open-collector outputs that support wired-OR configurations and flexible logic-level translation. The TSSOP-8 package provides a compact surface-mount footprint suitable for dense boards, and the device is positioned by Diodes Incorporated for industrial, automotive, and consumer electronics applications. Technically, each comparator in the LM2903ATH-13 is a differential amplifier stage with a PNP input pair that allows input common-mode voltages extending down to the negative rail, including slightly below ground in single-supply operation. The open-collector output stage requires an external pull-up resistor, which lets designers adapt the output swing to 3.3V, 5V, or higher logic rails independently of the comparator supply. Hysteresis, when needed, is added with a small amount of positive feedback around the comparator. Typical applications include voltage threshold detection and supervision in power supplies, level shifting between analog front ends and microcontroller inputs, oscillator and timing circuits, current-sense limit detection, and signal conditioning in industrial and automotive electronic control units. A key design consideration is that the open-collector output mandates a pull-up resistor to the desired logic rail, and for slowly moving input signals a few millivolts of hysteresis should be added to prevent output chatter near the switching threshold. This page adds value beyond the manufacturer datasheet by consolidating drop-in alternative comparisons, pinout information, application guidance, and sourcing details in one place for design and procurement engineers.

RFC Hubungi kami
LM2903AVQDR - 38V Dual Comparator, 0.37mV Offset | Texas Instruments
LM2903AVQDR

LM2903AVQDR - 38V Dual Comparator, 0.37mV Offset | Texas Instruments

The Texas Instruments LM2903AVQDR is a dual differential comparator with a 38 V maximum supply rating, 0.37 mV low input offset voltage, 3.5 nA low input bias current, and a 1 µs response time. The device contains two independent open-collector output comparators and is packaged in an 8-pin SOIC. It is designed for general-purpose signal comparison across industrial, automotive, communications, and power-control systems. A differential comparator is an analog integrated circuit that compares two input voltages and changes its output state according to their polarity. The LM2903 belongs to the comparator hierarchy, where a voltage comparator is an amplifier IC used for threshold detection, level translation, protection, and control-loop signaling. Its two independent channels allow one package to perform two separate comparison functions or to operate as one window-comparator stage. Key features include a maximum rating of 38 V, a typical input offset voltage of 0.37 mV, input bias current of 3.5 nA, and supply current of 200 µA per comparator. The open-collector outputs can sink useful output current and require an external pull-up resistor, making them suitable for wired logic buses and isolated relay-driving arrangements. The manufacturer also identifies a 2 kV human-body-model ESD rating for the improved LM2903 family. The A/V qualification of this orderable device combines the enhanced voltage capability associated with the LM2903V family with the 8-SOIC production configuration. The 1 µs response time is useful for threshold monitoring where the system must react quickly but does not require the sub-microsecond delay of a high-speed comparator. Two open-collector channels also allow outputs to be pulled to different logic levels rather than being tied to a fixed internal supply rail. Typical uses include overvoltage and undervoltage monitoring in industrial power supplies, battery threshold detection, sensor signal conditioning, industrial control inputs, and automotive monitoring systems. In each case, the comparator converts an analog input relationship into a digital indication that can drive a controller, an optocoupler, a relay, or another logic input. When laying out the circuit, keep the open-collector pull-up resistor close to the relevant output and verify the required sink current. Inputs must remain within the device's permitted common-mode and supply limits, and unused comparator channels should be configured according to the manufacturer's recommended practice rather than left floating. The SOIC thermal pad is not used because this package has eight leads. This product page combines the manufacturer's family specifications with package, lifecycle, cross-reference, and engineering guidance. It also identifies practical drop-in alternatives and distinguishes exact orderable variants from parts that use a different package or qualification level.

RFC Hubungi kami
LM2903AVQDRG4 - Dual Comparator for Analog Control | TI
LM2903AVQDRG4

LM2903AVQDRG4 - Dual Comparator for Analog Control | TI

The Texas Instruments LM2903AVQDRG4 is a dual differential analog comparator with two independent comparison channels, a 2 V to 36 V supply range, and an 8-pin SOIC package. It provides open-collector outputs, 2 mV typical input offset voltage, and a 0.3 µs response time for general-purpose signal detection and control applications. An analog comparator is a semiconductor IC that compares two input voltages and changes its output state when one input crosses the other. The LM2903 family belongs to the comparator hierarchy, where a comparator is an amplifier-class interface IC used for thresholding, sensing, level translation, and system protection. Its two channels can operate independently, allowing one package to implement two comparison functions. The principal electrical features are the 2 V to 36 V single-supply operating range, 2 mV typical offset voltage, and 0.3 µs response time. Single or dual supplies are supported, while the open-collector output stage requires an external pull-up resistor to establish a valid logic-high voltage. The V-grade designation identifies the low-supply-current version of the LM2903 family. Internally, each channel includes a differential input stage, a bias network, and an open-collector output stage. The two comparators share common supply and ground pins but retain separate non-inverting, inverting, and output connections. This arrangement supports independent sensing tasks while reducing package count compared with two single-channel comparator ICs. Typical uses include overvoltage and undervoltage detection, battery monitoring, sensor thresholding, temperature-control loops, industrial control signals, and digital system conditioning. The wide supply range is useful in equipment operating from regulated low-voltage rails as well as industrial systems with higher supply voltages. The open-collector output also permits wired signal combining when the system uses compatible pull-up rails and logic levels. For reliable operation, select pull-up resistors appropriate for the output logic voltage and account for the open-collector sink-current limit. Input common-mode range, output saturation behavior, and supply bypass requirements must be checked against the operating conditions. Decoupling capacitors should be placed close to the supply and ground pins to limit coupling from adjacent switching circuitry. This page organizes the LM2903AVQDRG4 specifications, practical application guidance, and verified drop-in alternatives into one engineering reference. It also highlights the distinctions among automotive, B-revision, and comparator-family alternatives so that a replacement can be selected by package, pinout, voltage envelope, and intended application rather than by package name alone.

RFC Hubungi kami
LM2903AVQDRG4Q1 - 36V AEC-Q100 Dual Open-Collector Comparator | Texas Instruments
LM2903AVQDRG4Q1

LM2903AVQDRG4Q1 - 36V AEC-Q100 Dual Open-Collector Comparator | Texas Instruments

The Texas Instruments LM2903AVQDRG4Q1 is an AEC-Q100 Grade 0 and 1 automotive dual differential comparator with two independent, open-collector output channels, supplied from a single 2 V to 36 V rail or from dual ±1 V to ±18 V supplies, and housed in an 8-pin SOIC (D) package rated for -40 °C to +125 °C. A comparator is a differential amplifier whose output changes state when one input exceeds the other by more than a defined offset. It converts an analog voltage relationship into a digital logic level, which places it in the hierarchy of analog signal conditioning > comparator > differential amplifier > analog IC. Because both channels are fully independent, one package provides two separate threshold decisions, which halves board area compared with two single comparators. Key features of the LM2903-Q1 device family include a 36 V maximum single-supply rating, open-collector outputs that can sink up to tens of milliamperes into a pull-up network, very low supply-current drain of roughly 0.4 mA per channel that is largely independent of supply voltage, and input common-mode range that extends close to both supply rails. The automotive-qualified grade adds AEC-Q100 Grade 0 and 1 qualification, supporting ambient temperatures from -40 °C to +125 °C, and the device is rated for the electrostatic and transient conditions typical of 12 V and 24 V vehicle electrical systems. Each of the two channels presents a non-inverting and an inverting input, a common supply ground, and a separate open-collector output. Because the output stage is open collector rather than push-pull, the output polarity is set by the position of the external pull-up resistor, and the output can be wired-ORed with other open-collector devices such as system alarm lines, sensor buses, or fault indicators. This is a deliberate design choice in automotive systems where a single fault line must be shared and the output must be pulled low in the fail-safe direction. Typical applications include 12 V and 24 V battery rail overvoltage and undervoltage supervision, window regulator and body electronics threshold detection, ABS wheel-speed sensor conditioning, motor and solenoid current-limit protection, industrial PLC level and limit switching, and DC power-supply UVLO and OVLO window comparators. Each of these applications depends on the wide 36 V supply headroom, the low quiescent current, and the ability to sink a logic-level pull-up current directly. A key design consideration is that open-collector outputs require an external pull-up resistor, typically 10 kΩ to 100 kΩ, and that the output leakage current in the high state limits the maximum usable pull-up resistance. Placing the pull-up close to the output reduces susceptibility to noise pickup on the shared fault line. Automotive designs should also keep the comparator input traces short and away from switching nodes, because the high-impedance differential inputs are the most sensitive part of the signal chain and are the dominant source of false threshold transitions. This page combines the LM2903-Q1 technical specifications, an AEC-Q100-aware pin and package breakdown, and a drop-in alternative table that compares automotive-qualified and commercial catalog alternatives in the same 8-SOIC footprint, so engineers can identify a pin-compatible replacement without re-laying out the board.

RFC Hubungi kami
LM2903AVQDRQ1 - 36V AEC-Q100 Dual Open-Collector Comparator | Texas Instruments
LM2903AVQDRQ1

LM2903AVQDRQ1 - 36V AEC-Q100 Dual Open-Collector Comparator | Texas Instruments

The Texas Instruments LM2903AVQDRQ1 is an AEC-Q100 Grade 0 and Grade 1 qualified dual differential comparator with open-collector (open-drain) outputs, operating from a single supply of 2 V to 36 V or from dual supplies of ±1 V to ±18 V, packaged in an 8-pin SOIC (D) surface-mount package rated for -40 °C to +125 °C. A comparator is a type of analog integrated circuit that compares two input voltages and produces a logic-level output indicating which input is higher. Because a comparator only switches when its inputs cross, it is used as a threshold detector rather than as an amplifier, sitting in the signal chain between a sensor or divider network and the logic block that reacts to the decision. In the wider hierarchy, a comparator belongs to the amplifier and comparator IC family within the broader category of analog and mixed-signal integrated circuits. Key features of this device include two independent comparison channels, rail-to-rail input common-mode operation, an open-collector output stage that can sink up to 16 mA and drive external relays or TTL loads, low supply current that stays essentially independent of supply voltage, and a 1.3 µs propagation delay. The open-collector architecture allows several comparators to be wire-ORed together on a shared bus, and the output can be pulled up to any logic level the system uses. Internally the device is built around a differential input stage, a second stage, and a bipolar open-collector output driver, which is why the supply current draw is described as independent of supply voltage. The wide 36 V total supply capability is what allows the same part to sit directly on 12 V and 24 V automotive and industrial rails without external protection, and the low offset and low bias currents keep the threshold error small compared with the resistive dividers usually placed in front of it. Typical applications include automotive battery and 12 V rail monitoring, industrial sensor threshold conditioning, overvoltage and undervoltage protection in power supplies, motor drive current-limit and stall detection, medical instrumentation window comparison, and IoT sensor-level detection. The AEC-Q100 Grade 0 and Grade 1 qualification supports use in harsh automotive environments where temperature extremes and ESD events are common. When designing with this part, remember that the open-collector output needs an external pull-up resistor, and that a device driving a large relay or solenoid coil needs a flyback diode to protect the output transistor from inductive voltage spikes. Keep the input divider resistors close to the pins to limit parasitic pickup on high-impedance threshold networks.

RFC Hubungi kami
LM2903AVQPWR - Dual Differential Comparator | Texas Instruments
LM2903AVQPWR

LM2903AVQPWR - Dual Differential Comparator | Texas Instruments

Texas Instruments LM2903AVQPWR is a dual differential comparator designed for single-supply or dual-supply operation, with two independent open-collector output stages in an 8-pin TSSOP package. The device is specified for enhanced voltage operation, a wide supply-voltage range, and a typical supply-current drain of 0.4 mA per comparator. Its differential inputs allow each comparator to compare an inverting input against a non-inverting input and generate a logic-level indication of the comparison result. A comparator is an analog semiconductor that evaluates two input voltages and produces a digital output indicating which input is higher. The LM2903 belongs to the voltage-comparator hierarchy, where it functions as a general-purpose interface between analog sensing circuits and digital logic. It is commonly used to monitor supply rails, detect threshold crossings, translate sensor signals, protect equipment, and support simple control loops. The open-collector outputs require an external pull-up resistor when the output must drive a logic node. The LM2903AVQPWR includes two independent comparator channels, allowing separate comparisons within one package. The enhanced-voltage LM2903V family is identified in the manufacturer product information as supporting a wide range of supply voltages. The typical supply-current drain is listed as 0.4 mA per comparator, making the device suitable for low-power monitoring and embedded control systems where supply efficiency matters. The device uses an 8-pin TSSOP package designated PW by Texas Instruments. The product information identifies the operating-temperature range as -40°C to 125°C for LM2903AVQPWR. The package is suitable for compact surface-mount PCB layouts, while the open-collector outputs provide flexible interface options to TTL, CMOS, open-drain buses, relay drivers, and other systems. The two channels share the supply pins but retain independent input and output functions. Typical applications include automotive and industrial voltage supervision, battery monitoring, overvoltage and undervoltage detection, signal conditioning, window comparison, sensor thresholding, and logic-level translation. The -40°C to 125°C temperature range supports applications across industrial and automotive environments, subject to the device-specific operating and absolute-maximum ratings in the manufacturer datasheet. Designers should account for the open-collector output when selecting the external pull-up resistor. The resistor value determines output rise time, while the transistor's sink-current capability limits the permissible load. Input common-mode range, output saturation level, response time, supply-voltage limits, and input offset should be checked against the specific application before finalizing the design. This product overview combines the LM2903AVQPWR identity, TSSOP package information, comparator function, application guidance, and same-footprint replacement context to support faster engineering review and sourcing decisions.

RFC Hubungi kami
LM2903AVQPWRG4 - Dual Comparator | Texas Instruments
LM2903AVQPWRG4

LM2903AVQPWRG4 - Dual Comparator | Texas Instruments

The Texas Instruments LM2903AVQPWRG4 is a dual differential comparator with two independent open-collector, rail-to-rail outputs, a 2 V to 36 V single-supply operating range, and an 8-pin TSSOP package. Each comparator provides precise voltage comparison with an input offset voltage as low as 0.37 mV and an input bias current of 3.5 nA for the B-version family. The LM2903 family is designed for low-power voltage-detection and threshold-monitoring circuits. A differential comparator is an analog integrated circuit that compares two input voltages and changes its output state when the difference between those voltages crosses a defined threshold. Within the comparator hierarchy, this device belongs to the general-purpose comparator, analog IC, and semiconductor categories. Its open-collector outputs allow the output stage to sink current while remaining compatible with external pull-up resistors, making it useful for wired logic, relay drivers, and level translation. The LM2903B family offers low input offset voltage of 0.37 mV, low input bias current of 3.5 nA, supply current of 200 µA per comparator, and a faster response time of 1 µs. The B version is identified by Texas Instruments as a drop-in replacement for LM293, LM393, and LM2903 devices in both A and V grades. It also provides an extended temperature range and an HBM ESD rating of 2 kV. The device supports operation from 2 V to 36 V with a single supply or from ±1 V to ±18 V with dual supplies. Each comparator has a differential input arrangement, an open-collector output, and independent operation, allowing one section to monitor a positive threshold while the other monitors a different signal. Because the outputs are open collector, a pull-up resistor is required when driving CMOS, MCU, or other high-impedance logic inputs. Typical uses include battery threshold detection, industrial sensor interfaces, overvoltage and undervoltage monitoring, window comparators, and general control loops. The wide supply range supports both low-voltage embedded systems and higher-voltage industrial environments. The 8-TSSOP package also permits compact placement where the open-collector output can be used to drive a pull-up-connected indicator or interface. Designers should account for the open-collector architecture by adding a pull-up resistor at each output and checking that the required sink current stays within the device limits. Input common-mode range, supply voltage, output pull-up voltage, and response timing must also be reviewed against the intended system. For replacement decisions, verify the exact suffix and package because A, B, and V grades differ in qualification and specific performance limits. This product page combines manufacturer specifications, package details, application guidance, and verified drop-in alternatives to support component selection and board-level replacement planning. Texas Instruments also provides a dedicated LM2903 product page and manufacturer part-details listing for lifecycle, documentation, and ordering review.

RFC Hubungi kami
LM2903AVQPWRG4Q1 - Dual 32V Automotive Comparator | Texas Instruments
LM2903AVQPWRG4Q1

LM2903AVQPWRG4Q1 - Dual 32V Automotive Comparator | Texas Instruments

Texas Instruments LM2903AVQPWRG4Q1 is an automotive, dual differential comparator with two independent open-collector outputs, a 36 V maximum supply voltage, and an 8-pin TSSOP package. The device supports single-supply or dual-supply operation, with input voltage ranges of 2 V to 36 V or ±1 V to ±18 V. It is AEC-Q100 qualified in Grade 0 and Grade 1. A differential comparator is an analog integrated circuit that compares two input voltages and changes its output state according to their relationship. The LM2903AVQPWRG4Q1 belongs to the comparator hierarchy: differential comparator, analog comparator, linear integrated circuit, and semiconductor. Its open-collector outputs allow the output transition speed and current limit to be controlled with an external pull-up resistor, making the device useful in sensing, threshold detection, and automotive interface circuits. The next-generation LM2903-Q1 family provides lower offset voltage, lower supply current, lower input bias current, and lower propagation delay than earlier LM2903 variants. Published family information lists a typical propagation delay of 1.3 µs, typical supply current of 0.4 mA per comparator, maximum input bias current of 50 nA, and maximum input offset voltage of 7 mV at 25°C. A comparison listing also identifies a maximum offset voltage of 2 mV at 5 V for this ordering variant. Two independent comparators are integrated into one package, allowing simultaneous monitoring of two thresholds or complementary sensing functions. The extended 36 V supply rating supports systems whose signal and supply levels exceed the range of conventional low-voltage comparators. Improved 2 kV ESD performance adds handling and application robustness in cost-sensitive automotive and industrial environments. Typical uses include automotive battery and power-system monitoring, sensor threshold detection, overvoltage and undervoltage indication, window-comparator circuits, and industrial control inputs. The open-collector output can directly pull a logic rail low, while the external pull-up resistor establishes the high state. Each comparator remains electrically independent, so the two channels can also implement complementary decisions. Designers should select the external pull-up resistor to suit the output voltage, sink-current capability, rise-time target, and system leakage currents. Inputs should remain within the device's common-mode limits at all supply combinations, and unused comparator inputs must be tied to a defined voltage rather than left floating. Automotive designs should use the specified AEC-Q100 grade and verify the complete operating temperature range for the ordered configuration. This product page combines the manufacturer family description, package and qualification details, practical comparator design guidance, and a focused comparison with same-footprint alternatives. It is intended to help engineers identify the correct orderable device and implement its open-collector outputs without treating a similar package number as an automatic functional replacement.

RFC Hubungi kami
LM2903AVQPWRQ1 - Dual 36 V Automotive Comparator | TI
LM2903AVQPWRQ1

LM2903AVQPWRQ1 - Dual 36 V Automotive Comparator | TI

Texas Instruments LM2903AVQPWRQ1 is an AEC-Q100 Grade 0 and 1 automotive dual differential comparator with a 2 V to 36 V single-supply range, open-collector outputs, and an 8-pin TSSOP (PW) package. It provides two independent comparison channels, a typical response time of 1.3 us, and rail-to-rail input operation for flexible signal-threshold detection. A comparator is a high-gain analog circuit that determines whether one input voltage is above or below another input voltage. Its output changes state when the differential input crosses the selected threshold. The dual differential comparator category extends this function to two independent channels, making it useful for battery monitoring, sensing, window detection, and control loops. In the hierarchy of semiconductor components, a comparator belongs to the broader analog and interface IC family. The LM2903AVQPWRQ1 combines a wide operating supply range with low supply-current operation. Manufacturer product information identifies the device as an automotive high-voltage dual comparator qualified for AEC-Q100 Grade 0 and 1. Each channel uses an open-collector output, allowing multiple comparators to share a pull-up network for wired-AND signaling. The typical propagation delay is 1.3 us, while the operating temperature range extends from -40 C to +125 C. Each comparator channel includes a non-inverting input, an inverting input, and an open-collector output. The eight-pin TSSOP package keeps the two channels separate while supporting compact PCB placement. Because open-collector outputs require an external pull-up resistor, the output voltage is set by the pull-up supply and resistor rather than by a push-pull output stage. The dual architecture also allows one device to monitor two independent threshold conditions. Typical uses include automotive battery and power-rail monitoring, industrial threshold detection, sensor conditioning, overvoltage and undervoltage protection, and automotive control modules. The 2 V to 36 V operating range is particularly useful when a circuit operates from an automotive battery-derived supply. The 1.3 us response time supports comparisons where the threshold result must be captured quickly, although propagation delay and input overdrive should be checked against the system timing budget. When designing a PCB for LM2903AVQPWRQ1, place the device near the sensed signals and keep input traces short to reduce noise pickup. Route each open-collector output with an appropriate pull-up resistor, verify absolute-maximum input and supply voltages, and account for input bias current when choosing high-impedance divider networks. The automotive-qualified grade and -40 C to +125 C rating support harsh-temperature systems, provided the surrounding power distribution and protection components are appropriately rated. This product page consolidates the exact ordering information, package details, technical specifications, drop-in alternatives, and application-specific design guidance for engineers evaluating the LM2903AVQPWRQ1. It also distinguishes true same-package drop-in choices from related comparators that require a different footprint.

RFC Hubungi kami
LM2903BIDDFR - Dual Open-Collector Comparator | Texas Instruments
LM2903BIDDFR

LM2903BIDDFR - Dual Open-Collector Comparator | Texas Instruments

The Texas Instruments LM2903BIDDFR is a dual industrial-grade standard comparator with two independent comparison channels, open-collector outputs, and rail-to-rail input capability. It is packaged in an 8-pin SOT-23-THN (DDF) surface-mount package and is specified for an operating temperature range of -40°C to 125°C. A comparator is an analog semiconductor that compares two input voltages and produces a logic-level result indicating which input is higher. A dual comparator integrates two comparison channels into one package, allowing simultaneous sensing, threshold detection, or window monitoring. Within the broader hierarchy, the LM2903B belongs to the comparator and amplifier IC family and ultimately to the wider semiconductor and signal-conditioning market. The LM2903BIDDFR combines an open-collector output stage with a differential-input architecture. Open-collector outputs can pull a logic node low when the comparator changes state, while an external pull-up resistor establishes the high state. This arrangement provides flexible interface voltage selection and is useful with TTL, MOS, and CMOS-compatible loads. Each channel supports independently routed non-inverting and inverting inputs. The B-version product family provides improved characteristics relative to earlier LM2903, LM293, and LM393 variants while maintaining pin-for-pin drop-in compatibility. The manufacturer identifies LM2903B as a drop-in replacement for the earlier devices, and its common-mode input range includes ground. These features make the comparator suitable for systems that compare bipolar or single-ended sensor signals without requiring a fully differential amplifier. Typical applications include industrial control systems, automatic test equipment, power-supply supervision, motor-control circuits, window comparators, and general threshold detection. The dual-channel configuration can implement two independent safety thresholds, compare upper and lower limits, or monitor complementary sensor outputs without requiring two separate comparator packages. The primary design consideration is the open-collector output: each output requires an appropriate pull-up resistor and must remain compatible with the voltage and timing requirements of the connected logic circuit. Input polarity, output state, and propagation behavior should be checked against the specific logic levels and system timing before production release. This page combines the exact ordering information, package details, operating limits, application guidance, and design considerations for the LM2903BIDDFR. It also organizes sourcing questions and replacement guidance around the device's actual dual-comparator function and open-collector interface.

RFC Hubungi kami
LM2903BIDGKR - Dual 38V Industrial Comparator | Texas Instruments
LM2903BIDGKR

LM2903BIDGKR - Dual 38V Industrial Comparator | Texas Instruments

Texas Instruments LM2903BIDGKR is a dual differential comparator with two independent channels, a maximum rated supply voltage of 38 V, open-collector outputs, and an 8-VSSOP package. It operates from a 2 V to 36 V supply, supports input common-mode and differential voltages up to ±38 V, and is specified as a rail-to-rail input device with 0.37 mV input offset voltage. A comparator is an analog integrated circuit that compares two input voltages and changes its output state when the difference crosses a threshold. The LM2903B belongs to the comparator hierarchy within analog and power-management semiconductors. Unlike an operational amplifier, each channel does not require feedback compensation for linear amplification, and its open-collector output must connect to an external pull-up resistor when driving a logic input. Key B-version improvements include lower offset voltage, lower input bias current, lower supply current, faster response, and stronger input protection than the original LM2903. The device features 0.37 mV input offset voltage, 3.5 nA input bias current, 200 μA supply current per comparator, 1 μs response time, and a 2 kV human-body-model ESD rating. Its outputs are compatible with TTL, MOS, and CMOS logic according to the manufacturer documentation. Each internal comparator is electrically independent, but both channels share the supply pins and ground connection. Separate input and output pins allow one channel to perform threshold detection while the other performs window monitoring, current sensing, or another independent comparison. The open-collector architecture provides wired-AND behavior when multiple outputs share a pull-up node, although rise time then depends on the resistor, capacitance, and leakage current. Typical uses include industrial sensor thresholding, battery and power-supply monitoring, overvoltage detection, signal conditioning, and embedded control systems. The wide 38 V maximum rating is useful in industrial environments where input transients can exceed nominal logic levels, but system designers must still validate signal levels and protection requirements for every operating condition. For layout, route the comparator inputs away from switching nodes and place input-referred components close to their associated pins. Select the external output pull-up to balance sink-current capability against rise time. Verify input common-mode range, output pull-up voltage, package thermal conditions, and system shutdown behavior against the manufacturer datasheet before production release. This page combines the LM2903B electrical characteristics, package and pin information, application guidance, design checks, and verified drop-in alternatives. It also highlights practical considerations for pull-up selection, input protection, noise, and industrial qualification that engineers can apply directly during schematic review and PCB design.

RFC Hubungi kami
LM2903BIDR - Dual 36V Open-Collector Comparator | Texas Instruments
LM2903BIDR

LM2903BIDR - Dual 36V Open-Collector Comparator | Texas Instruments

The Texas Instruments LM2903BIDR is a dual industrial-grade differential comparator with two independent channels, a maximum supply rating of 36 V, open-collector outputs, and a 1 µs response time. It is supplied in an 8-pin SOIC (D) package and is specified for operation from -40 °C to +125 °C. The B-version family also provides a low 0.37 mV input offset, 3.5 nA input bias current, and 200 µA supply current per comparator. A comparator is an analog integrated circuit that determines whether one input voltage is above or below another and switches its output when the differential input crosses a threshold. In the broader semiconductor hierarchy, a comparator belongs to the amplifier and comparator IC family rather than an operational amplifier. Open-collector outputs are useful when multiple devices must share a wired bus or when an external pull-up resistor selects the logic voltage independently of the comparator supply. The LM2903BIDR supports single- or dual-supply operation, allowing its input and output signals to be referenced around ground in control, sensing, and protection circuits. Its industrial temperature range makes it suitable for equipment operating beyond consumer-temperature limits. The two channels are independent, so one device can perform two threshold functions while sharing a package, although output pull-up components and supply decoupling remain external. Verified distributor and manufacturer results identify the device as a standard, general-purpose, rail-to-rail-input comparator with open-collector outputs and an 8-SOIC footprint. Texas Instruments describes the B-version as a next-generation member of the LM393 and LM2903 families, emphasizing lower offset, lower bias current, lower supply current, faster response, wider supply capability, and improved ESD robustness. Typical applications include DC overvoltage monitoring, industrial sensor thresholds, battery-powered indication, window comparators, and relay or alarm activation. Because an open-collector output does not actively drive a high voltage, every application must provide a suitable pull-up resistor and account for its sink-current limit. The collector voltage and supply limits should be checked against the manufacturer datasheet before designing to absolute maximum conditions. For PCB design, place input resistors close to the relevant pins, decouple the supply close to the device, and route high-impedance input traces away from switching nodes. Where open-collector outputs drive cables or long PCB traces, use a strong pull-up and consider a buffer if additional noise immunity or edge control is required. This page combines verified manufacturer and distributor details with engineering guidance for selecting, sourcing, and replacing the component.

RFC Hubungi kami
LM2903BIDSGR - Dual 38V Comparator | Texas Instruments
LM2903BIDSGR

LM2903BIDSGR - Dual 38V Comparator | Texas Instruments

Texas Instruments LM2903BIDSGR is a dual differential analog comparator with a maximum rating of 38 V, open-collector outputs, and an 8-WSON package measuring 2 x 2 mm. Each channel supports rail-to-rail input behavior, while the device uses 200 uA of supply current per comparator and has a typical response time of 1 us. The B-version combines low power consumption with improved switching performance. An analog comparator is a semiconductor that compares two input voltages and produces a logic-level output indicating which input is higher. Comparators belong to the broader analog IC hierarchy alongside amplifiers, voltage references, and data converters. They are used to implement threshold detection, sensing, overvoltage protection, oscillator functions, and digital-interface conditioning when open-collector outputs are advantageous. The LM2903B family provides a maximum input rating of 38 V, an input offset voltage as low as 0.37 mV, and an input bias current as low as 3.5 nA. Its open-collector output stages can sink output current and support pull-up connections to the system supply, allowing the device to interface with TTL, MOS, and CMOS logic. Dedicated input ESD clamps provide an HBM ESD rating of 2 kV. The B-version improves the original LM2903 family through lower offset voltage, lower input bias current, lower supply current, faster response, wider supply capability, and improved input ruggedness. Its common-mode input voltage range includes ground, which supports sensing around a zero-volt reference when the supply conditions permit operation near that boundary. The 1 us response time also makes the device suitable for faster control loops than classic general-purpose comparators. Typical uses include DC overvoltage and undervoltage detection, sensor threshold interfaces, battery and power-supply monitoring, window comparators, relaxation oscillators, and industrial control logic interfaces. The compact 2 x 2 mm WSON package helps reduce board area where dense analog and mixed-signal layouts are required. Designers should preserve adequate input and output separation when operating near absolute maximum limits, place pull-up resistors close to each open-collector output, and route sensitive input traces away from switching nodes. The exposed thermal pad should be connected to the ground plane according to the package land pattern and thermal design guidance. This page combines the LM2903BIDSGR electrical characteristics, package and lifecycle information, replacement assessment, comparison data, and practical PCB guidance to help engineers evaluate the device quickly and design a robust comparator circuit.

RFC Hubungi kami
LM2903BIPWR - Dual 36V Comparator | Texas Instruments
LM2903BIPWR

LM2903BIPWR - Dual 36V Comparator | Texas Instruments

The Texas Instruments LM2903BIPWR is a dual industrial-grade comparator with a 2 V to 36 V supply range, 1 µs response time, and open-collector outputs in an 8-pin TSSOP package. Each channel provides an independent comparison function, with input offset voltage as low as 0.37 mV and input bias current as low as 3.5 nA. The device is designed for robust threshold detection, industrial signal conditioning, and systems powered from higher-voltage rails. A voltage comparator is a signal-conditioning integrated circuit that compares two input voltages and changes its output state according to their relationship. The LM2903B belongs to the comparator hierarchy, where it functions as a general-purpose comparator, analog signal interface, and power-management building block. Its two channels can monitor independent sensors or participate in window-detection and overvoltage-protection circuits. Open-collector outputs also make wired-AND behavior possible when multiple comparators share a pull-up resistor. The B-version improvements include a maximum supply rating of 38 V, a 2 kV human-body-model ESD rating, low input offset, low input bias current, and supply current of 200 µA per comparator. The 1 µs response time supports faster decision-making than legacy comparators, while the rail-to-rail input characteristic permits operation from the ground rail to the positive supply rail. The industrial temperature range covers applications from -40 °C to +125 °C. Each output uses an open-drain transistor rather than a push-pull output stage. This architecture provides flexible voltage-level compatibility because an external pull-up resistor determines the output voltage. It also permits several outputs to be connected together when the resulting wired-AND behavior is intentional. A pull-up resistor is required even when only one output is used; without it, the output cannot rise to a valid high state. Typical uses include industrial sensor interfaces, battery threshold detection, motor and actuator protection, window comparators, relay-control logic, and power-supply monitoring. The 36 V operating range is useful in industrial systems where the comparator may directly observe a protected signal node. The low 200 µA per-comparator supply current also makes the device suitable for low-power monitoring when the signal source can be brought close to the supply rail. For reliable layout, route each comparison input directly to its device pin and keep feedback or output loops away from the input traces. Place the output pull-up resistor close to the open-collector output, and use a local supply bypass capacitor where the power rail can produce disturbance. Account for input common-mode voltage and output leakage when designing the system threshold. This page combines the Texas Instruments ordering information, device specifications, package details, pin assignments, sourcing workflow, and practical replacement guidance to support faster component selection and PCB design. Use the manufacturer datasheet for the complete electrical characteristics, timing definitions, and application guidance.

RFC Hubungi kami
LM2903BQDRQ1 - Dual Rail-to-Rail Comparator | Texas Instruments
LM2903BQDRQ1

LM2903BQDRQ1 - Dual Rail-to-Rail Comparator | Texas Instruments

Texas Instruments LM2903BQDRQ1 is an automotive dual differential comparator with two open-collector outputs, rail-to-rail input operation, and a supply range of ±18 V or 36 V total. It is packaged in an 8-pin SOIC (D) and rated for operation from -40 °C to +125 °C. The device is identified by Texas Instruments as an AEC-Q100 automotive-grade option within the LM2903B-Q1 family. A comparator is an analog signal-processing IC that compares two input voltages and produces a digital output indicating which input is higher. Comparators belong to the broader amplifier IC category and are commonly used as threshold detectors, sensor interfaces, overvoltage monitors, and control-loop decision elements. Unlike a general-purpose operational amplifier, the LM2903BQDRQ1 is intended primarily for open-loop voltage comparison rather than precision closed-loop amplification. The primary features of the LM2903BQDRQ1 are its dual differential input architecture, open-collector output stage, rail-to-rail input capability, and broad supply-voltage range. The open-collector outputs require an external pull-up resistor, allowing the output state to be set by the external pull-up voltage. This arrangement is useful when interfacing with automotive logic, transistor-based level conversion, relay drivers, or multiple devices sharing a wired bus. Its -40 °C to +125 °C temperature range supports applications across industrial, automotive, and other extended-temperature environments. The LM2903B-Q1 family is described by Texas Instruments as a next-generation version of the industry-standard LM2903-Q1 comparator family. Its stated improvements include lower offset voltage, higher supply-voltage capability, lower supply current, lower input bias current, lower propagation delay, and improved 2 kV ESD performance, together with drop-in replacement convenience. The target MPN combines these automotive-grade features in the 8-SOIC package identified by ordering code D. Typical uses include battery-pack threshold detection, automotive sensor conditioning, overvoltage and undervoltage protection, industrial control inputs, window or level monitoring, and logic-level translation. In each case, the two comparator channels can monitor independent thresholds or operate as complementary detectors. The open-collector architecture also permits a system designer to select the pull-up voltage and current rather than being restricted to a fixed push-pull output voltage. When laying out a board, place the pull-up resistor close to the open-collector output and keep comparator input traces short to reduce susceptibility to injected noise. Confirm output-current limits, input common-mode behavior, supply sequencing, and logic thresholds in the manufacturer datasheet before finalizing the design. Consider a device with push-pull outputs when an external pull-up is undesirable, or verify an alternate comparator carefully when its output architecture or input range differs. This page combines the manufacturer’s automotive comparator information, verified ordering details, and practical drop-in guidance. It helps engineers identify the correct package, temperature grade, output type, and replacement options while emphasizing the electrical checks that matter during schematic and PCB design.

RFC Hubungi kami
LM2903BQPWRQ1 - Dual Automotive Comparator | Texas Instruments
LM2903BQPWRQ1

LM2903BQPWRQ1 - Dual Automotive Comparator | Texas Instruments

Texas Instruments LM2903BQPWRQ1 is an automotive dual differential comparator with two independent open-collector outputs, rail-to-rail input capability, and operation across single or dual supply rails up to 36 V. It is packaged in an 8-pin TSSOP tape-and-reel configuration. The LM2903B-Q1 family is positioned as the next generation of the automotive LM2903-Q1 comparator line, combining cost-conscious design with lower offset voltage, lower supply current, lower input bias current, lower propagation delay, and improved 2 kV ESD performance. A comparator is an analog semiconductor that evaluates two input voltages and produces a logic-level indication of their relationship. The differential input stage determines whether the non-inverting input is above or below the inverting input, while the open-collector output stage provides a flexible interface for pull-up resistors and digital logic. In the LM2903BQPWRQ1, the dual-channel architecture provides two independent comparator functions in one package, reducing board area when two sensing channels are required. Key advantages include rail-to-rail input operation, a common-mode input range that includes ground, an operating supply range extending to 36 V, and open-collector outputs that can sink current from an external pull-up. The open-collector architecture is particularly useful when interfacing to TTL, CMOS, or MOS logic, or when multiple open-drain outputs need to share a bus with suitable wired-AND behavior. Automotive qualification supports its use in cost-sensitive vehicle electronics where tolerance for electrical transients and ESD events is important. The LM2903B-Q1 generation improves several parameters relative to the earlier LM2903-Q1 family while retaining compatibility with established LM2903-family applications. Its lower offset voltage supports more accurate switching thresholds, while reduced supply and input bias currents can simplify power budgeting and high-impedance sensor interfaces. Lower propagation delay is useful in control loops and threshold-detection circuits, and the improved 2 kV ESD capability strengthens robustness at exposed connector and signal interfaces. Typical uses include automotive battery and power-system monitoring, sensor threshold conditioning, overvoltage and undervoltage detection, window comparison, industrial control logic, and dual-level signal qualification. Because the outputs are open collector, the design must include suitable pull-up resistors when a valid high output is required. Inputs must also remain within the device's absolute maximum ratings, and unused channels require appropriate input states to prevent unstable output behavior. Designers should verify the exact input common-mode range, differential input limits, output pull-up voltage, and timing budget against the manufacturer datasheet for the selected operating condition. Automotive systems should additionally check the required qualification, temperature grade, ESD class, and production test requirements. This page combines exact catalog information, package details, drop-in alternatives, and application-specific engineering guidance for faster component selection and PCB planning.

RFC Hubungi kami
LM2903D - Dual Open-Collector Comparator | Texas Instruments
LM2903D

LM2903D - Dual Open-Collector Comparator | Texas Instruments

The Texas Instruments LM2903D is a dual differential analog comparator with two independent comparator channels, an operating supply range of 2 V to 36 V, a response time of 300 ns, and an 8-pin SOIC package. Each channel provides open-collector output behavior for level translation, relay driving, and wired-AND logic functions. The device is specified for operation from -40 °C to +125 °C according to the available manufacturer comparison data. An analog comparator is an integrated circuit that compares two input voltages and produces a logic-level output indicating which input is higher. The LM2903D belongs to the comparator hierarchy within analog and mixed-signal semiconductors, providing a simple alternative to an operational amplifier configured as a comparator. Its two channels operate independently, allowing one package to implement two threshold decisions or to control complementary functions in a single circuit. The open-collector outputs are a defining electrical feature. Each output transistor can pull its output low, but it cannot actively drive the output high, so an external pull-up resistor is required. Multiple open-collector outputs can share one pull-up to create a wired-AND arrangement. This architecture also provides a useful form of output isolation while remaining compatible with standard 5 V and 3.3 V digital logic levels when the pull-up rail is selected appropriately. The 2 V to 36 V supply capability allows operation from low-voltage analog systems through conventional industrial control rails. Its 300 ns response time supports applications where decisions must be made faster than typical slow comparators but where nanosecond-level precision is unnecessary. The operating temperature range covers industrial environments, although production designs should still verify temperature-dependent input offset, output-current, and propagation-delay behavior using the selected manufacturer's complete datasheet. Typical uses include industrial sensor conditioning, battery monitoring, overvoltage detection, window or level comparators, relay and solenoid interfaces, and digital control systems that require open-collector outputs. The SOIC-8 package is also appropriate for through-hole-style PCB assembly and manual rework, although SOIC-8 is larger than modern comparator packages such as SOT-23 and MSOP-8 variants. When designing with the LM2903D, always place the input and pull-up networks close to their associated pins, and account for input common-mode limits at the selected supply voltage. A pull-up resistor is not optional because the open-collector output cannot source current. Reviewing the voltage drop across the pull-up and the output transistor's current rating is essential when several outputs share the same node. This page consolidates verified distributor listings, manufacturer references, pin-compatible alternatives, package details, and practical circuit guidance. It also distinguishes directly interchangeable devices from higher-speed or higher-precision alternatives whose electrical behavior may require different design assumptions.

RFC Hubungi kami
LM2903DE4 - Dual 36V Open-Collector Comparator | Texas Instruments
LM2903DE4

LM2903DE4 - Dual 36V Open-Collector Comparator | Texas Instruments

Texas Instruments LM2903DE4 is a dual differential comparator built for general-purpose signal conditioning and threshold detection. The device contains two independent comparators, supports a 2 V to 36 V single-supply operating range, and provides open-collector outputs in an 8-pin SOIC package. Its 300 ns response time makes it suitable for systems that require faster decisions than the related LM393B family while retaining the familiar open-collector interface. A comparator is an analog integrated circuit that compares two input voltages and produces a digital logic state indicating which input is higher. Within the broader hierarchy of interface ICs, comparators extend analog signal conditioning into threshold control, protection, sensing, and discrete logic activation. The LM2903DE4 is specifically a dual differential comparator: each half can independently compare an inverting input with a non-inverting input while sharing common supply and ground connections. The principal features include two independent channels, a 2 V to 36 V supply range, an approximately 300 ns response time, and open-collector outputs compatible with TTL, MOS, and CMOS circuits. The common-mode input range includes ground, and the differential input range is equal to the maximum-rated supply voltage of ±38 V for the family. Each output can sink external current while remaining in a high-impedance state when inactive, requiring an external pull-up resistor for normal logic-high operation. Differential comparison is especially useful when a sensor or signal source is referenced to another voltage rather than to ground. By placing the threshold on the non-inverting input and the sensed signal on the inverting input, the comparator can provide overvoltage, undervoltage, temperature, current, or level detection. Because the channels are independent, the same package can implement two thresholds, compare two unrelated signals, or combine two decisions locally. Typical applications include industrial sensor interfaces, overvoltage and reverse-polarity protection, window comparators, motor and relay control, power-supply supervision, and embedded control systems. The open-collector outputs are particularly useful for wired-AND arrangements, relay-driver interfaces, and level translation because the output stage can remain disconnected while an external pull-up establishes the logic-high voltage. The principal design consideration is the open-collector output. Place each pull-up resistor close to the relevant output and select it to balance rise time against sink-current demand. Also check input common-mode limits, supply operating range, output leakage, and the timing relationship between the reference voltage and sensed signal before using the comparator for high-speed pulse detection. This page consolidates the manufacturer specifications, package and pin information, orderable alternatives, comparison data, and practical application guidance into a design-focused reference for engineers evaluating the LM2903DE4.

RFC Hubungi kami
LM2903DG - Dual Comparator, 2-36V, SOIC-8 | onsemi
LM2903DG

LM2903DG - Dual Comparator, 2-36V, SOIC-8 | onsemi

The onsemi LM2903DG is a dual differential voltage comparator with open-collector outputs, low input offset voltage of 2 mV typical, and a wide supply voltage range of 2V to 36V (single supply) or +/-1V to +/-18V (split supply), housed in an 8-pin SOIC package rated from -40C to +105C. A voltage comparator is an analog IC that compares two input voltages and outputs a digital signal indicating which input is higher. It sits at the boundary between the analog and digital domains within the signal-chain hierarchy: comparator -> analog front-end IC -> signal conditioning -> power/semiconductor. The LM2903 family, originally introduced as the LM393 series, is the industry-standard general-purpose comparator, and the LM2903 variant extends the temperature range for industrial use. Key features include two independent comparators in one package, open-collector outputs that support rail-to-rail output swings and wired-OR configurations, a common-mode input range that extends down to ground (negative rail) during single-supply operation, and a very low supply-current drain of approximately 0.4 mA per comparator that is largely independent of supply voltage. Input offset voltage as low as 2 mV makes the device suitable for precision threshold detection. Technically, the device permits single- or split-supply operation as long as the difference between the two supplies is 2V to 36V and VCC is at least 1.5V more positive than the input common-mode voltage. Typical propagation delay (response time) is approximately 1.3 us, adequate for threshold detection, level shifting, and slow-to-medium speed switching tasks. The open-collector stage requires an external pull-up resistor to define the logic-high level, allowing direct interfacing to 5V, 3.3V, or other logic families. Typical applications include limit comparators and over-voltage/under-voltage detectors in power supplies, window comparators in battery-management and industrial monitoring circuits, zero-crossing detection, oscillator and pulse-generator timing circuits, and logic-level translation in automotive and industrial controllers where the -40C to +105C range is required. When designing with the LM2903DG, add hysteresis (a small positive-feedback resistor around the comparator) to prevent output chatter near slowly changing input thresholds, and place a pull-up resistor of 1k to 100k on each output. This page consolidates distributor availability data, pin-compatible drop-in alternatives from multiple manufacturers, and practical design notes that go beyond the manufacturer datasheet alone.

RFC Hubungi kami