Produk (44,000+)

LM2904ITP/NOPB - Dual 26V 700kHz Op Amp | Texas Instruments
LM2904ITP/NOPB

LM2904ITP/NOPB - Dual 26V 700kHz Op Amp | Texas Instruments

The Texas Instruments LM2904ITP/NOPB is a dual, general-purpose operational amplifier with a 26 V maximum supply voltage and a 700 kHz rated operating bandwidth, supplied in an 8-DSBGA package. The ordering suffix identifies the tape-and-reel configuration. Its two amplifier circuits, 1 MHz gain-bandwidth product and 0.1 V/us slew rate place it in the classic low-power, general-purpose operational-amplifier category. An operational amplifier, or op amp, is a voltage-controlled differential amplifier intended to amplify the difference between two input voltages. It belongs to the amplifier IC hierarchy, within the broader semiconductor and analog signal-processing categories. A dual op amp combines two amplifier channels in one package, allowing a circuit to implement two signal-processing functions while reducing board area and the number of external components. The LM2904ITP/NOPB is identified as a standard general-purpose amplifier. The listed electrical characteristics include a 26 V maximum supply voltage, 700 kHz operating bandwidth, 1 MHz gain-bandwidth product and 0.1 V/us slew rate. These values position the device for moderate-frequency signal handling rather than high-speed precision work. The 8-DSBGA package also gives PCB designers a compact option for dual-channel analog circuits. The device belongs to the long-established LM2904 family and is associated with the LM158-series operating-amplifier architecture, consisting of two independent, high-gain, internally frequency-compensated amplifiers designed for single-supply operation over a wide voltage range. Internal frequency compensation removes the need for an external dominant-pole capacitor in typical closed-loop configurations, simplifying implementation and stabilizing operation across supported gain settings. Typical uses include low-frequency sensor conditioning, audio preamplification, instrumentation, active filtering, and general dual-amplifier analog signal chains. The dual-channel configuration is particularly useful when a design needs symmetric gain stages, a voltage follower alongside a signal amplifier, or two related sensor interfaces sharing one compact package. Designers should verify the exact input common-mode range, output swing, input offset, input-bias current, supply-current behavior and temperature limits against the manufacturer datasheet before finalizing a circuit. Place the 8-DSBGA on a PCB layout that separates input, output and supply paths appropriately, and use suitable bypassing capacitance at the power pins. Because the package is a fine-pitch BGA rather than a leaded package, assembly capability and land-pattern compatibility also require verification. This product page organizes the confirmed ordering, package, electrical, and commercial information while distinguishing documented LM2904-family options from unconfirmed substitutions. It also provides application guidance, comparison fields, and a pinout limitation notice so engineers can make a package-aware sourcing decision without assuming that every electrically similar dual op amp is a true drop-in replacement.

RFC Hubungi kami
LM2904ITPX/NOPB - Dual 26V, 700kHz Op Amp | Texas Instruments
LM2904ITPX/NOPB

LM2904ITPX/NOPB - Dual 26V, 700kHz Op Amp | Texas Instruments

Texas Instruments LM2904ITPX/NOPB is a dual, general-purpose operational amplifier with two independent, internally frequency-compensated amplifiers, a maximum supply rating of 26 V, and a gain-bandwidth product of 700 kHz. The device is supplied in an 8-DSBGA package and is intended for single-supply operation across a broad voltage range. An operational amplifier, commonly called an op amp, is an analog integrated circuit that amplifies the voltage difference between its differential inputs. Its high open-loop gain, negative feedback operation, and internal frequency compensation make it useful for signal conditioning, comparison, filtering, and instrumentation. The LM2904 contains two amplifier channels in one package, allowing one IC to serve two related analog functions. The LM2904ITPX/NOPB provides two amplifier circuits in a compact 8-DSBGA package. Texas Instruments describes the device as a low-power dual operational amplifier with a 700 kHz gain-bandwidth product. A listing for the exact MPN also identifies a 0.1 V/µs slew rate, surface-mount construction, and a -40°C to 85°C temperature range. Tape-and-reel packaging supports automated assembly and high-volume production. Internally frequency compensation means each amplifier can operate with a minimum closed-loop gain determined by its internal design rather than requiring an external compensation network in ordinary applications. This characteristic simplifies analog circuit implementation, although the closed-loop gain, output swing, stability, and supply headroom still require verification against the operating conditions of the final circuit. Typical uses for the LM2904ITPX/NOPB include industrial sensor conditioning, instrumentation, low-frequency active filtering, analog signal buffering, and general-purpose dual-amplifier circuits. The 26 V maximum supply rating is useful for industrial and automotive-adjacent designs that operate above conventional 5 V analog rails, provided the applied voltage remains within the device rating and suitable input and output common-mode conditions are maintained. For PCB design, place decoupling capacitors close to the supply and ground connections, preserve the package footprint and pin assignments, and verify thermal performance when both channels operate continuously. Decoupling and stability depend on the source impedance, load, feedback network, and supply arrangement, so prototype the final filter or amplifier configuration before high-volume production. This product page combines the exact-orderable MPN, electrical attributes, package information, application guidance, and practical design considerations. It also distinguishes documented drop-in alternatives from functional equivalents that require different footprints, helping engineers avoid substitutions that cannot be mounted safely on the original PCB land pattern.

RFC Hubungi kami
LM2904LVIDDFR - 5.5V Dual 1MHz Op Amp | Texas Instruments
LM2904LVIDDFR

LM2904LVIDDFR - 5.5V Dual 1MHz Op Amp | Texas Instruments

The Texas Instruments LM2904LVIDDFR is a dual, low-voltage operational amplifier with a 5.5 V maximum supply voltage, 1 MHz gain-bandwidth product, and 3 mV output offset voltage, housed in an 8-pin TSOT-23 package. Each amplifier channel provides independent input, output, power, and feedback connections, allowing one package to implement two signal-processing functions. An operational amplifier is an analog amplifier whose high open-loop gain is controlled by external feedback components. Within the power-management semiconductor hierarchy, the LM2904LV belongs to the broader operational-amplifier family, combining low-voltage compatibility, low power consumption, and general-purpose signal conditioning in one dual-channel device. The LM2904LV family is intended for portable equipment, industrial controls, sensors, communications, and other low-voltage systems. Key characteristics include a 2.7 V to 5.5 V supply range, approximately 90 uA supply current, a typical slew rate of 0.5 V/us, and rail-to-rail output swing. The 1 MHz gain-bandwidth product supports moderate-frequency amplification, while the 3 mV offset-voltage figure defines the typical input imbalance that must be considered when operating near the output range limits. These characteristics make the device suitable for battery-powered instrumentation and general-purpose analog front ends. The dual architecture reduces component count and board area compared with two separate single-channel amplifiers. Each channel can be configured as an inverting amplifier, a non-inverting amplifier, a comparator-like comparator configuration, or an analog buffer when operated with suitable feedback and loading. Independent channel use provides flexibility, although common-mode and output-swing limitations still apply to both channels. Typical uses include current-sense amplifier front ends, sensor signal conditioning, low-frequency active filters, audio preamplification, industrial interface circuits, and portable measurement equipment. In current sensing, the device can amplify the small voltage developed across a low-value shunt resistor. In sensor interfaces, it can provide gain or impedance conversion before an ADC input. Its low 90 uA supply-current characteristic is particularly useful in battery-operated equipment. When designing around the LM2904LVIDDFR, verify the input common-mode range and output swing against the actual signal amplitude. Keep feedback-loop routing compact, provide local supply bypassing, and avoid placing the input node beside high-current switching paths. Check the 5.5 V maximum supply rating and ensure the 2.7 V lower operating limit is sufficient for the complete system supply range. This product page consolidates the manufacturer specifications, package information, practical application guidance, and verified substitution assessment for the LM2904LVIDDFR. It also distinguishes confirmed drop-in candidates from devices that require a package or functional change, helping engineers evaluate replacements without changing PCB requirements.

RFC Hubungi kami
LM2904LVIDGKR - Dual 5.5V 1MHz Op Amp | Texas Instruments
LM2904LVIDGKR

LM2904LVIDGKR - Dual 5.5V 1MHz Op Amp | Texas Instruments

The Texas Instruments LM2904LVIDGKR is a dual, low-voltage operational amplifier designed for single-supply or dual-supply industrial and instrumentation circuits. It provides two amplifier channels, a 1 MHz gain-bandwidth product, a 3 mV maximum input offset voltage, and operation from a single 2.7 V to 5.5 V supply in an 8-pin VSSOP (DGK) package. The part is intended for general-purpose signal conditioning where low supply voltage, modest bandwidth, and short-circuit tolerance are more important than high-speed performance. An operational amplifier is an analog integrated circuit that amplifies the difference between its inverting and non-inverting inputs. Within the broader hierarchy, the LM2904LV is a voltage-feedback operational amplifier, which places it in the amplifier IC and analog signal-conditioning categories. Two independent channels allow one package to implement two amplifiers, reducing component count and simplifying board layout in designs such as sensor conditioning, active filtering, and low-frequency instrumentation. Key features include the dual-channel configuration, 1 MHz gain-bandwidth product, 3 mV input offset voltage rating, and a maximum 5.5 V supply voltage. The low-voltage LM2904LV family is intended for portable and low-voltage systems where the conventional 26 V LM2904 would be excessive. Its general-purpose positioning also makes it useful as a cost-conscious alternative to higher-performance precision amplifiers when the signal bandwidth and offset requirements are moderate. The device uses a conventional complementary-input architecture suitable for closed-loop voltage feedback. Because its unity-gain bandwidth is 1 MHz, applications are generally limited to low-frequency amplification and filtering rather than high-speed signal chains. Input and output stability depends on the surrounding feedback network, source impedance, load, and bypass capacitance, so the manufacturer datasheet should be used when selecting compensation and decoupling values. Typical uses include sensor-amplifier front ends, transducer signal conditioning, active low-pass filters, audio preamplifier stages, buffer stages, and general dual-amplifier analog boards. The low-voltage supply range makes the device appropriate for 3.3 V and 5 V systems, although rail-to-rail input and output capability is not implied by the 5.5 V maximum supply specification. The primary design consideration is supply headroom. Common-mode input voltage, output swing, and output-current capability all depend on the selected supply voltage and load. Verify those limits against the application before committing to the VSSOP footprint. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured according to the manufacturer datasheet rather than left floating. This page consolidates the device specifications, ordering information, package details, application guidance, and engineering trade-offs into one reference for component selection and PCB design.

RFC Hubungi kami
LM2904LVIDR - 1MHz Dual Low-Voltage Op Amp | Texas Instruments
LM2904LVIDR

LM2904LVIDR - 1MHz Dual Low-Voltage Op Amp | Texas Instruments

The Texas Instruments LM2904LVIDR is a dual, low-voltage, general-purpose operational amplifier with a 5.5 V maximum supply rating, 1 MHz gain-bandwidth product, and 3 mV input offset voltage. It is supplied in an 8-pin SOIC package and is designed for cost-sensitive signal-conditioning and analog-instrumentation applications. An operational amplifier, or op amp, is an analog integrated circuit that amplifies the difference between two input voltages. The LM2904LVIDR contains two amplifiers in one package, making it useful for dual-channel signal chains, buffer stages, transducers, and low-voltage control systems. Its family position is operational amplifier -> voltage-feedback amplifier -> analog amplifier -> integrated circuit. The device is specified for dual operation at a 5.5 V maximum supply. Texas Instruments describes the LM2904LV as a dual, 5.5 V, 1 MHz operational amplifier with a 3 mV offset-voltage rating. The 8-SOIC package supports conventional surface-mount assembly, while the dual configuration reduces board area for applications that need two amplifier channels. The LM2904LVIDR is intended for instrumentation and general-purpose analog designs where a low-voltage supply is important. Typical uses include sensor-interface amplification, audio signal conditioning, process-control loops, and buffering of low-level analog signals. The 1 MHz bandwidth is suitable for moderate-frequency rather than high-speed precision applications, and the 3 mV input offset specification should be considered in sensor and instrumentation designs requiring low input-level accuracy. For stable operation, follow the manufacturer's recommended supply, common-mode input, output-voltage, and decoupling guidelines from the LM2904LV datasheet. Place the supply bypass capacitor close to the device and keep sensitive input routing short to reduce noise pickup. The two amplifier channels in the package are independent, but each requires correct biasing and appropriate output-load conditions. This product summary combines the LM2904LV family specifications with practical guidance for PCB layout, application selection, and replacement planning. It is designed to help engineers identify whether the 8-SOIC dual op amp meets the voltage, bandwidth, offset, and package requirements of a new analog design.

RFC Hubungi kami
LM2904LVIPWR - Dual 5.5V 1MHz Op Amp | Texas Instruments
LM2904LVIPWR

LM2904LVIPWR - Dual 5.5V 1MHz Op Amp | Texas Instruments

Texas Instruments LM2904LVIPWR is a dual, general-purpose operational amplifier with a 5.5 V maximum supply rating, 1 MHz gain-bandwidth product, and 3 mV input offset voltage in an 8-pin TSSOP (PW) package. The two amplifiers are intended for low-voltage signal-conditioning and analog-processing systems operating from -40°C to +125°C. An operational amplifier is an active analog component that amplifies the voltage difference between its non-inverting and inverting inputs. The LM2904LV belongs to the LM290xLV low-voltage operational-amplifier family, combining two amplifier channels in one package. This makes the device suitable for applications such as signal buffering, active filtering, differential amplification, instrumentation, and low-level analog conditioning. The headline specifications are a 1 MHz gain-bandwidth product, a 3 mV offset voltage, and a 5.5 V maximum supply rating. These characteristics are useful for moderate-bandwidth, general-purpose analog designs where compactness and dual-channel functionality matter more than high-speed precision performance. The operating-temperature range of -40°C to +125°C supports use across industrial and extended-temperature equipment. The LM2904LV uses conventional internal compensation and is configured as a dual operational amplifier. Its 1 MHz bandwidth supports general-purpose closed-loop signal work, while the two channels can implement independent amplifier functions or work together in differential, summing, and feedback configurations. Design calculations should use the manufacturer datasheet for gain-bandwidth behavior, output swing, input common-mode limits, and output-drive capability. Typical uses include sensor-signal conditioning, audio preamplification, industrial control interfaces, low-frequency active filters, and general analog buffers. In dual-rail or single-supply systems, the circuit designer must verify the allowable input and output common-mode ranges against the actual supply voltage. Output loading and feedback-loop stability also require evaluation when driving capacitive or long external cables. Use the manufacturer pin-description table when assigning PCB tracks and verify the exposed-pad requirements and recommended land pattern for the TSSOP package. Place input and feedback components close to the relevant amplifier pins, maintain short ground-return paths, and provide local supply bypassing to reduce noise and prevent feedback from unrelated circuitry. This product page combines the key manufacturer specifications, ordering and package information, application guidance, and replacement-selection considerations in one engineering-focused reference. The comparison and design notes are intended to accelerate schematic selection, footprint verification, and first-board bring-up for dual low-voltage operational-amplifier designs.

RFC Hubungi kami
LM2904LVQDGKRQ1 - 5.5V 1MHz Automotive Dual Op Amp | Texas Instruments
LM2904LVQDGKRQ1

LM2904LVQDGKRQ1 - 5.5V 1MHz Automotive Dual Op Amp | Texas Instruments

Texas Instruments LM2904LVQDGKRQ1 is an automotive-grade, dual operational amplifier designed for low-voltage signal-chain systems. It operates from a 2.7 V to 5.5 V supply, provides a 1 MHz gain-bandwidth product, and is specified with a 3 mV input offset voltage. The device is supplied in an 8-VSSOP package and provides two amplifier circuits in one package. An operational amplifier is an analog integrated circuit that uses high-gain differential amplification to compare an inverting input with a non-inverting input. Within the broader hierarchy, it is a voltage-feedback amplifier, an amplifier IC, and a signal-conditioning semiconductor. The dual configuration allows one device to process two related channels, reducing board area when both channels share the same supply and ground reference. The LM2904LV-Q1 family targets automotive and industrial low-voltage applications where supply efficiency, cost, and dependable operation are important. The 2.7 V to 5.5 V operating range supports systems powered from regulated 3.3 V and 5 V rails. Its 1 MHz bandwidth makes it suitable for general-purpose amplification, buffering, voltage comparison, filtering, and sensor-interface functions rather than high-speed signal processing. The dual amplifier architecture is useful in sensor conditioning, current sensing, control loops, line-driver buffers, and automotive body electronics. Each amplifier can be used independently, allowing the two channels to monitor complementary signals or perform separate functions in a compact circuit. Input and output stability, common-mode range, and output-drive capability should be checked against the actual signal levels and load conditions. The principal design trade-off is that this is a general-purpose, low-voltage amplifier rather than a precision or high-speed device. Its 3 mV offset specification is appropriate for many sensing and control paths, but systems requiring tighter offset accuracy need to evaluate the bias current, input voltage range, noise, and application error budget. This page combines the manufacturer specifications, package information, application guidance, comparison parameters, and practical drop-in selection notes for engineers evaluating the LM2904LVQDGKRQ1.

RFC Hubungi kami
LM2904LVQDRQ1 - 5.5V Dual 1MHz Op Amp | Texas Instruments
LM2904LVQDRQ1

LM2904LVQDRQ1 - 5.5V Dual 1MHz Op Amp | Texas Instruments

Texas Instruments LM2904LVQDRQ1 is an automotive-grade, dual operational amplifier with a 5.5 V maximum supply, 1 MHz gain-bandwidth product, and 3 mV output offset voltage in an 8-pin SOIC package. The two independent channels make it suitable for signal conditioning, transducer amplification, feedback control, and automotive electronics operating from 2.7 V to 5.5 V. An operational amplifier, or op amp, is a voltage-feedback amplifier used to increase signal amplitude, buffer inputs, implement active filters, and regulate feedback loops. Within the semiconductor hierarchy, the LM2904LV-Q1 belongs to the operational-amplifier, analog-amplifier, and signal-conditioning IC categories. Its low-voltage supply operation distinguishes it from conventional high-voltage LM2904 devices while retaining the familiar dual-channel pin arrangement. The LM2904LV-Q1 family is specified for low-voltage operation from 2.7 V to 5.5 V. Its 1 MHz gain-bandwidth product supports general-purpose closed-loop amplification at relatively low frequencies. The 3 mV offset specification improves DC accuracy in applications where input bias and offset errors influence the output. Two amplifiers are integrated in one 8-pin SOIC, reducing board area while providing independent channels for complementary signal paths. This device is intended for cost-sensitive, low-voltage systems that still require automotive-grade temperature qualification and robust general-purpose performance. The dual configuration can implement two noninverting amplifiers, two voltage followers, differential signal conditioning, or independent error-amplifier functions. Because it is not rail-to-rail, input and output common-mode ranges must remain within the device's specified operating limits when supplies are restricted. Typical uses include automotive sensor interfaces, body and comfort-system signal conditioning, low-voltage control loops, current sensing with external resistors, active filters, and general industrial modules operating from 2.7 V or 3.3 V rails. A 5 V system can use the full 5.5 V maximum supply while retaining appropriate design margin for supply variation and transient behavior. When laying out the circuit, keep input and feedback traces short, provide local supply bypassing, and avoid placing long routes beside high-current switching nodes. Check the common-mode input range at the actual signal amplitude and ensure that output swing remains below the output-current and supply-voltage limits. Decoupling capacitors should connect directly to the supply and ground pins rather than through shared narrow traces. This product page combines the manufacturer specifications with practical design guidance, package-level comparisons, application examples, and available drop-in alternatives. It supports faster component selection for engineers who need a dual, low-voltage, automotive operational amplifier in the standard 8-pin SOIC footprint.

RFC Hubungi kami
LM2904M - Dual 26V 700kHz Op Amp | Texas Instruments
LM2904M

LM2904M - Dual 26V 700kHz Op Amp | Texas Instruments

The Texas Instruments LM2904M is a dual, general-purpose operational amplifier with a 26 V supply rating, 700 kHz gain-bandwidth product, and an 8-SOIC package. According to the Texas Instruments LM2904 product page, the device is intended for low-power analog signal-processing systems where two amplifiers are useful in a single package. The verified distributor listing identifies LM2904M as a standard two-circuit amplifier in an 8-SOIC package, and the Mouser result specifies the operating-temperature range as -40 °C to 85 °C. An operational amplifier is an analog integrated circuit that uses feedback to amplify the difference between its non-inverting and inverting inputs. The LM2904M belongs to the broader operational-amplifier, analog-amplifier, and semiconductor hierarchies. In practical circuits, each internal amplifier can serve as an inverting amplifier, non-inverting amplifier, comparator, buffer, or integrator when operated with suitable external components and supply voltages. The 26 V supply rating provides compatibility with conventional industrial and analog signal ranges, while the 700 kHz gain-bandwidth product supports low-to-moderate-frequency signal amplification. The dual configuration reduces package count when a circuit needs two amplifier channels. Its general-purpose designation indicates broad applicability rather than a specialized low-noise, high-speed, precision, or automotive-only function. The LM2904M uses an 8-SOIC surface-mount package, corresponding to the soic-8 package library key. The verified results do not provide a complete electrical specification table in the supplied excerpts, so detailed parameters such as input offset voltage, input bias current, slew rate, output-current capability, common-mode range, quiescent current, and noise values are marked as data needed rather than estimated. Typical applications include low-frequency analog signal conditioning, instrumentation interfaces, sensor buffers, audio preamplifier stages, and general dual-amplifier circuits. The dual channel can also be used for active filtering or control loops where two matched functional amplifier sections are useful. Because the available information is general-purpose and distributor-oriented, the designer should verify operating-point limits, loading, stability, and temperature margin against the manufacturer datasheet before release. For PCB implementation, place bypass capacitors close to the supply pins and route sensitive input and feedback traces away from switching nodes and high-current paths. Confirm the exact pin orientation and electrical limits before assembly. This page combines verified manufacturer and distributor references with explicitly marked data gaps rather than inventing missing specifications.

RFC Hubungi kami
LM2904M-FS - Dual 26V Op Amp 500V/ms | onsemi
LM2904M-FS

LM2904M-FS - Dual 26V Op Amp 500V/ms | onsemi

The onsemi LM2904M-FS is a dual general-purpose operational amplifier in an 8-pin SOIC package, with two independent internally frequency-compensated amplifier channels designed for operation from a single power supply. Key characteristics include a 250 nA input-bias current, 500 V/ms slew rate, and approximately 2 mV input offset voltage for the listed configuration. An operational amplifier is an analog signal-conditioning IC that compares an inverting input with a non-inverting input and amplifies the voltage difference between them. The dual-amplifier configuration places two independent amplifiers in one package, making the LM2904M-FS suitable for signal conditioning, feedback-control loops, sensor amplification, and general analog signal paths. Within the product hierarchy, it is a dual operational amplifier within the amplifier-IC and analog-semiconductor categories. The LM2904M-FS combines a 26 V maximum supply capability from the LM2904 family with low input-bias current and a 500 V/ms slew rate. Its internally compensated architecture removes the need for an external frequency-compensation network in common closed-loop applications. The two independent channels can operate in non-inverting, inverting, voltage-follower, comparator-style, and feedback configurations, provided the design respects the device's common-mode and output-voltage limits. The 8-SOIC footprint provides a conventional surface-mount assembly format with exposed leads on both package sides. Each half of the amplifier uses four pins: two inputs, one output, and the power connection. The standard SOIC-8 pin arrangement simplifies PCB layout, but normal single-supply operation requires bypassing the positive supply pin to ground and accounting for the input and output common-mode limitations near the supply rails. Typical applications include low-frequency industrial instrumentation, buffered sensor interfaces, audio preamplifier stages, analog monitoring, and general-purpose dual-amplifier signal conditioning. The LM2904M-FS is particularly useful where two related analog channels are required on one board, such as an input stage and feedback amplifier in a control circuit. For high-speed or very low-offset instrumentation, a precision amplifier family may be preferable. Decouple the power supply with a short, low-inductance path from the positive supply pin to ground, and route the amplifier output away from high-current switching nodes. Avoid using the device outside its input common-mode range, especially in single-supply circuits where the input approaches ground. Stable feedback-network layout and adequate output-load capability should be verified for every analog channel. This product page combines the exact LM2904M-FS ordering information with family-level electrical characteristics, a complete SOIC-8 pin map, practical application guidance, and a qualified drop-in comparison. It is designed to help engineers identify the correct footprint, understand the device's analog signal-conditioning role, and select among documented alternatives without changing the PCB land pattern.

RFC Hubungi kami
LM2904M/NOPB - Dual 26V 700kHz Op Amp | Texas Instruments
LM2904M/NOPB

LM2904M/NOPB - Dual 26V 700kHz Op Amp | Texas Instruments

Texas Instruments LM2904M/NOPB is a dual, low-power, high-gain operational amplifier rated for a 26 V supply and a 700 kHz gain-bandwidth product. The device is supplied in an 8-pin SOIC package and provides two independent, internally frequency-compensated amplifiers. It is designed for operation from a single power supply over a wide voltage range, while split-supply operation is also supported. The LM2904 family targets general-purpose analog signal conditioning where low power consumption, wide supply-voltage tolerance, and conventional dual-amplifier pin arrangements are important. An operational amplifier is an analog signal-processing IC that uses high open-loop gain to amplify differences between voltages applied to its inverting and non-inverting inputs. A dual operational amplifier contains two amplifier sections in one package, reducing board area and simplifying designs that require two independent gain stages. Within the broader semiconductor hierarchy, the LM2904 is an amplifier IC, then an operational amplifier, and finally a general-purpose analog building block for instrumentation, control, and signal-conditioning systems. Key characteristics include a 26 V maximum supply rating, a 700 kHz gain-bandwidth product, low-power operation, internally compensated frequency response, and operation across single- and split-supply arrangements. These features make the LM2904M/NOPB appropriate for transducers, low-frequency analog filters, sensor amplifiers, and general feedback-control circuits. The manufacturer describes the device as a dual low-power, high-gain operational amplifier specifically designed for single-supply operation over a wide range of voltages. Internally, each amplifier section uses frequency compensation to provide stable closed-loop operation without requiring an external compensation network. The two sections are independent, allowing them to serve separate signal paths or to work together as stages within a larger analog circuit. The 700 kHz gain-bandwidth product favors low-frequency rather than high-speed signal applications, while the 26 V supply rating provides useful headroom for industrial and automotive-style supply environments when the complete circuit satisfies the device ratings. Typical uses include amplifying outputs from sensors, buffering potentiometer and resistive-divider signals, implementing active low-pass or high-pass filters, and closing loops around slow analog control systems. Two amplifiers in one 8-pin SOIC can also form instrumentation-style signal-conditioning chains when the required common-mode range, output swing, and noise performance match the application. For PCB design, verify the exact pin orientation and exposed or non-exposed package details against the manufacturer pin configuration before routing copper. Place input and feedback components close to the relevant amplifier pins, maintain short ground-return paths, and use a stable local supply-decoupling arrangement. Avoid designs requiring the high slew rate and wide bandwidth of precision or high-speed amplifiers; the LM2904 is better suited to economical, general-purpose low-frequency analog functions. This product page consolidates the manufacturer family specifications, verified distributor identification, same-footprint alternatives, application guidance, and practical design considerations. It supports faster part identification while keeping datasheet verification, footprint review, and application-specific validation at the center of every engineering decision.

RFC Hubungi kami
LM2904M8-13 - Dual 700 kHz Op Amp | Diodes Incorporated
LM2904M8-13

LM2904M8-13 - Dual 700 kHz Op Amp | Diodes Incorporated

The Diodes Incorporated LM2904M8-13 is a dual general-purpose operational amplifier with two independent amplifier channels, a 700 kHz gain-bandwidth product, 2 mV input offset voltage, and an 8-MSOP package. It operates from a single supply between 3 V and 36 V, while split-supply operation is also supported. The device is characterized for industrial temperatures from -40°C to +125°C and uses green mold compound as standard. An operational amplifier is an analog signal-conditioning IC that amplifies the voltage difference between its inverting and non-inverting inputs. Operational amplifiers belong to the amplifier IC hierarchy and are widely used in sensor interfaces, filters, comparators, feedback-control loops, and low-frequency signal-processing circuits. The LM2904 combines two operational amplifiers in one compact surface-mount package, reducing board area compared with separate single-channel devices. Each LM2904 channel provides high open-loop gain and a 700 kHz gain-bandwidth product. The 2 mV input offset rating helps limit output error in DC amplifier and comparator circuits. Single-supply operation from 3 V to 36 V makes the device suitable for industrial control, instrumentation, sensor-conditioning, and power-supply feedback applications. Its -40°C to +125°C characterization also supports designs operating across extended temperature ranges. The LM2904 architecture supports both single-supply and split-supply operation. In a single-supply circuit, the input common-mode range, output swing, and bias arrangement remain important design constraints, particularly when signals remain close to ground. With dual supplies, the two amplifier channels can process signals around ground more naturally, although common-mode and output-range checks remain necessary at the supply limits. Typical uses include transimpedance amplifiers for low-frequency sensor signals, active filters for analog signal conditioning, threshold detectors, and closed-loop control amplifiers. The two channels may also be configured as a comparator, voltage follower, or differential amplifier, depending on the feedback network and system voltage requirements. Its 8-MSOP package is suited to compact industrial and embedded control boards where a dual amplifier offers practical space savings. For reliable layout, place input and feedback components close to their corresponding pins and keep sensitive input traces away from high-current switching paths. The power-supply pins require effective bypassing with a short ground return. Confirm that input and output signal levels remain inside the amplifier's usable common-mode and output ranges, particularly in single-supply configurations where the available signal headroom is reduced. This page combines the manufacturer datasheet, distributor listings, package and pinout information, application guidance, and replacement-selection criteria to support faster engineering evaluation. Review the electrical limits and application circuit in the Diodes Incorporated LM2904/LM2902 datasheet before finalizing a production design.

RFC Hubungi kami
LM2904MWC - Dual 26V 700kHz Operational Amplifier | Texas Instruments
LM2904MWC

LM2904MWC - Dual 26V 700kHz Operational Amplifier | Texas Instruments

The Texas Instruments LM2904MWC is a dual general-purpose operational amplifier designed for operation from a single power supply up to 26 V, with a gain-bandwidth product of 700 kHz. The device contains two independent amplifier channels and is supplied as a wafer for manufacturing and automated assembly processes. Its primary characteristics are a 26 V maximum supply rating, dual-circuit configuration, and 700 kHz gain-bandwidth product. An operational amplifier is an analog integrated circuit that amplifies the difference between its two input voltages. The LM2904 belongs to the operational-amplifier hierarchy within analog signal-processing ICs, where general-purpose devices are used for buffering, amplification, comparisons, filtering, instrumentation, and control loops. The two channels in the LM2904 can operate independently, allowing one device to implement two analog functions while conserving board area. The 700 kHz gain-bandwidth product makes the LM2904 appropriate for general-purpose signal conditioning rather than high-speed precision signal chains. Its 26 V supply capability is useful in industrial, automotive, and communications equipment where the circuit must tolerate higher supply rails than a conventional low-voltage amplifier. Because it is a general-purpose dual amplifier, designers can use the two channels for functions such as noninverting and inverting gain stages, buffers, active filters, comparators, and sensor-conditioning stages. The LM2904MWC is identified as a wafer sale rather than a finished surface-mount component. Wafer-level procurement is normally used by semiconductor manufacturers, test houses, and automated assembly operations that perform die-level inspection, final test, packaging, and board assembly. In such a process, manufacturing controls, known-good-die requirements, assembly yield, and lot traceability become as important as the electrical characteristics of the amplifier itself. Typical circuit roles include amplifying low-frequency sensor signals, buffering inputs to analog-to-digital converters, implementing active low-pass filters, and driving slow-changing control signals. The dual-channel organization is especially useful when a board requires two similar analog functions, such as an input stage and an output buffer. Decoupling capacitors should be placed close to the device supply pins, while input and output routing should be kept short and away from high-current switching paths. Because LM2904MWC is supplied as a wafer, engineers must confirm the die orientation, pin identification, tested temperature grade, quality level, and packaging flow before committing it to a manufacturing process. The official Texas Instruments LM2904 product page provides the authoritative ordering and technical information, while the manufacturer datasheet defines electrical characteristics, test conditions, and pin functions. This page organizes the confirmed LM2904MWC identity, package format, electrical headline parameters, engineering applications, and verified cross-reference landscape. It also distinguishes a directly replaceable drop-in option from related amplifier families that may require different packages, pin assignments, or performance validation.

RFC Hubungi kami
LM2904MX - Dual 26V 700kHz Operational Amplifier | TI
LM2904MX

LM2904MX - Dual 26V 700kHz Operational Amplifier | TI

Texas Instruments LM2904MX is a dual, general-purpose operational amplifier designed for operation from a single supply across a wide voltage range. The device contains two independent, internally frequency-compensated amplifiers in an 8-pin SOIC package. According to the manufacturer product page, the LM2904 family supports supply voltages up to 26 V and offers a gain-bandwidth product of 700 kHz. Its internally compensated architecture simplifies stable operation as a unity-gain buffer, while its high open-loop voltage gain and low-power design make it suitable for general signal-conditioning tasks. An operational amplifier is a high-gain analog building block used to amplify voltage differences, buffer inputs, perform comparisons, drive external loads, and implement active filters. Within the broader semiconductor hierarchy, the LM2904MX belongs to the operational-amplifier family, which falls under analog ICs and signal-conditioning semiconductors. Unlike precision or rail-to-rail amplifiers, the LM2904 is intended primarily for conventional supply-based operation and general-purpose applications. The principal features of the LM2904MX include two amplifier channels, an 8-SOIC package, a 700 kHz gain-bandwidth product, and operation from a single supply as high as 26 V. The device is internally frequency compensated, which allows operation at unity gain without an external compensation network. A typical slew rate is 0.3 V/us, making the amplifier appropriate for low-frequency analog processing rather than high-speed signal conditioning. The dual configuration also provides cost and board-area efficiency when a design needs two independent amplifier functions. Each channel can support feedback-based amplifier configurations such as non-inverting amplifiers, inverting amplifiers, voltage followers, summing circuits, and active filters. The LM2904MX is useful when signals must be conditioned with external resistors or capacitors and the application does not require the very low offset, low noise, high speed, or rail-to-rail input and output behavior associated with more specialized amplifier families. Its wide supply-voltage capability also permits operation from industrial-style elevated rails, subject to the device ratings. Typical applications include industrial control and instrumentation, sensor signal conditioning, power-supply feedback monitoring, audio and communications interface circuits, active filtering, and general-purpose analog buffers. In a 24 V industrial system, the 26 V maximum supply rating leaves little margin for transient overshoot, so input protection and rail clamping should be considered. The dual channels can serve separate signal paths, but designers should not assume that the two amplifiers share an output or that short-circuit protection makes unlimited current available. Design attention should focus on the input common-mode range, output swing, output-current capability, stability with the intended load, and the power dissipation created by the supply-to-output voltage difference. Place the device close to feedback and bypass components, use a local supply bypass capacitor, and route high-impedance input nodes with minimal parasitic capacitance. Verify operation across supply voltage, temperature, output load, and source resistance because these conditions affect common-mode range, output swing, and amplifier stability. This page combines manufacturer specifications, package details, drop-in alternatives, application guidance, and design checks to support component selection and PCB implementation. It also highlights the distinctions between the LM2904MX and commonly encountered LM2904 order codes so engineers can confirm electrical behavior, package compatibility, and assembly requirements before approving a replacement.

RFC Hubungi kami
LM2904MX/NOPB - Dual 26V 700kHz Op Amp | Texas Instruments
LM2904MX/NOPB

LM2904MX/NOPB - Dual 26V 700kHz Op Amp | Texas Instruments

Texas Instruments LM2904MX/NOPB is a dual general-purpose operational amplifier IC designed for low-power signal-conditioning applications. It operates from a supply voltage of up to 26 V, provides a gain-bandwidth product of 700 kHz, and is available in an 8-SOIC package. The two independent amplifier channels make the device suitable for dual-signal processing, instrumentation, control loops, and general analog signal amplification where a low-power, general-purpose amplifier is preferred. An operational amplifier is a voltage-gain amplifier whose closed-loop behavior is determined mainly by external feedback components. The LM2904 belongs to the dual general-purpose operational-amplifier family, combining two amplifier channels in one package. This integration reduces board area compared with two discrete single amplifiers and simplifies dual-channel designs requiring common supply voltage and similar operating characteristics. The manufacturer identifies the LM2904 as a low-power, dual operational-amplifier family for general-purpose applications. Its 26 V maximum supply rating supports higher-voltage analog systems than many low-voltage rail-to-rail amplifiers, while the 700 kHz gain-bandwidth product provides useful bandwidth for control, sensing, buffering, and signal-conditioning tasks. The 8-SOIC package offers a conventional surface-mount footprint that is practical for both new designs and upgrades of existing 8-pin amplifier boards. The MX ordering code denotes the manufacturer's SOIC package option, while /NOPB identifies the lead-free, non-PB-free finish. The 8-SOIC format is useful for prototypes, repair assemblies, and industrial equipment requiring a stable package outline. Designers should consult the manufacturer datasheet for the complete electrical limits, input/output characteristics, supply-current behavior, compensation information, pin assignments, and recommended operating conditions before releasing a production design. Typical LM2904 applications include two-channel sensor amplification, transducer-signal conditioning, low-frequency active filtering, voltage comparison, analog control loops, and general instrumentation. In these applications, the device can amplify signals from sensors, provide gain around analog front ends, or drive feedback networks when the operating range and load capability meet the circuit requirements. The dual channel can also implement differential or complementary stages where the two amplifiers operate within the same supply system. The primary design consideration is ensuring that the input common-mode range, output swing, supply voltage, noise, offset, and stability remain suitable for the application. Bypass capacitors should be placed close to the supply pins, while input, feedback, and compensation components should be positioned to minimize parasitic capacitance and unwanted feedback. Because the package exposes both amplifier channels, grounding and return-current paths should be planned to avoid coupling between the two signal paths. This product record combines the manufacturer specifications with package details, application-oriented guidance, technical comparison criteria, and verified sourcing references. It also distinguishes genuine same-footprint alternatives from broader functional equivalents, helping engineers make a board-level replacement decision while recognizing that electrical equivalence must be confirmed against the complete manufacturer datasheet.

RFC Hubungi kami
LM2904N - Dual 1 MHz 26 V Op Amp | Texas Instruments
LM2904N

LM2904N - Dual 1 MHz 26 V Op Amp | Texas Instruments

Texas Instruments LM2904N is a dual, internally frequency-compensated operational amplifier with two independent amplifiers, a 26 V maximum supply designation, and a 1 MHz gain-bandwidth product. It is supplied in an 8-pin PDIP package. The device is designed for general-purpose signal conditioning from industrial control to audio and sensor interfaces. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. Internally compensated LM2904N amplifiers are voltage-amplifier building blocks within the operational-amplifier, analog IC, and semiconductor hierarchies. Their differential inputs support filtering, buffering, summing, comparison, and feedback-control functions without requiring an external compensation network. The verified product information identifies two amplifiers, single-supply or split-supply use, low power drain, and a common-mode input range extending to ground or VEE. Its internally frequency-compensated architecture simplifies closed-loop design, while the dual configuration places two matched-function amplifiers in one package. However, the supplied data does not state output-current capability, input-offset voltage, input-bias current, slew rate, noise density, or operating-temperature limits. A key design consideration is supply configuration. Although the official TI product-page snippet specifies a 26 V product family designation, engineers must consult the exact manufacturer datasheet before setting rail voltage, input common-mode limits, output swing, and load current. Decoupling capacitance, input impedance, feedback topology, output loading, and thermal dissipation also remain datasheet- and layout-dependent. Typical uses include two-channel sensor conditioning, low-frequency active filters, audio preamplification, comparator-style signal detection with suitable saturation limits, control-loop buffering, and general dual-rail analog signal processing. The 1 MHz bandwidth is most appropriate for low-to-moderate-frequency signals rather than high-speed precision instrumentation. This data page combines verified manufacturer and distributor facts, pin-compatible replacement screening, and practical engineering guidance. It deliberately leaves unverified electrical values marked for completion rather than inferring specifications from related dual-amplifier families.

RFC Hubungi kami
LM2904N/NOPB Dual 1 MHz Op Amp 26 V | Texas Instruments
LM2904N/NOPB

LM2904N/NOPB Dual 1 MHz Op Amp 26 V | Texas Instruments

Texas Instruments LM2904N/NOPB is a dual, general-purpose operational amplifier with two independent amplifiers, a 26 V maximum supply rating, and 1 MHz gain-bandwidth performance in an 8-pin PDIP package. It is designed for single-supply operation across a broad voltage range, with split-supply operation also possible. The device provides internal frequency compensation and low supply-current drain, making it suitable for industrial control, instrumentation, sensor conditioning, and general analog signal-processing systems. An operational amplifier is an amplifier IC that uses high open-loop gain to increase the voltage difference between its differential inputs. In the feedback-defined signal chain, the LM2904N/NOPB belongs to the broader hierarchy of operational amplifier, analog amplifier, amplifier IC, and semiconductor. Its two independent channels allow two separate signal paths in one package, reducing board area compared with two single-amplifier packages. Key features include two amplifier circuits, a 26 V supply-voltage rating, 1 MHz gain-bandwidth, internal frequency compensation, and operation from a single supply or split supplies. The internal compensation removes the need for an external compensation network in ordinary closed-loop configurations. The dual-channel architecture is useful for two-stage filters, differential signal handling, buffer stages, and paired feedback networks. The 8-pin PDIP format supports through-hole assembly and prototyping systems. The LM2904-N family is intended for general-purpose applications where a single-supply-friendly amplifier with a wide supply range is more important than rail-to-rail output swing or very high bandwidth. The device can be used as an inverting amplifier, non-inverting amplifier, voltage follower, comparator in suitable applications, or the active element in a filter. Its internally compensated architecture simplifies design, although users should account for input common-mode limitations, output swing, stability margin, and slew-rate limits when selecting feedback values. Typical applications include low-frequency sensor interfaces, transducer signal conditioning, process-control loops, audio preamplifier stages, data-acquisition systems, and general power-control circuitry. Two amplifiers in one package are especially useful in dual-channel analog boards, instrumentation amplifiers using several gain stages, and active filter designs. The 1 MHz bandwidth supports many low- and mid-frequency industrial signals rather than high-speed video or RF tasks. For PCB design, use the manufacturer's pin-description table and package drawing when assigning connections. Keep input and feedback traces short, provide adequate supply bypassing, and avoid placing high-impedance input nodes next to switching nodes. If the source impedance is high, add a bias resistor or buffer stage to reduce input bias-current effects and offset error. Check the operating region against the device's supply and common-mode limits. This product page combines the LM2904N/NOPB ordering information with package, pinout, application, and drop-in replacement guidance. The comparison table highlights verified package and functional differences, while the design notes focus on practical PCB and signal-chain decisions for engineers evaluating the LM2904N/NOPB.

RFC Hubungi kami
LM2904NG - Dual Op Amp, 1MHz, 3-26V, PDIP-8 | onsemi
LM2904NG

LM2904NG - Dual Op Amp, 1MHz, 3-26V, PDIP-8 | onsemi

The onsemi LM2904NG is a general-purpose dual operational amplifier consisting of two independent, internally frequency-compensated op amps in a 400 mil 8-pin PDIP (0.300 in / 7.62 mm row spacing) package. It operates from a single supply of 3V to 26V or from dual supplies, delivers a gain bandwidth product of 1 MHz and a slew rate of 0.6 V/µs, and is rated for operation from -40C to +105C. An operational amplifier (op amp) is a high-gain voltage amplifier with differential inputs and a single-ended output that, together with resistors or capacitors in a feedback network, implements amplification, filtering, comparison, buffering and mathematical functions. The op amp sits at the core of the analog signal-chain hierarchy: amplifier IC -> analog front end -> mixed-signal system. The LM2904 family is the industry-standard dual op amp lineage originally popularized by National Semiconductor and carried forward by multiple manufacturers, including onsemi and Texas Instruments. Key features include a common-mode input voltage range that extends to ground/VEE, enabling the device to sense signals near 0V in single-supply systems, low power drain, and internal frequency compensation that eliminates external compensation components. Single-supply or split-supply operation gives designers flexibility across battery-powered and industrial 24V-class rails. The through-hole PDIP package suits prototyping, repair, education and legacy industrial boards. Architecturally, the LM2904NG uses circuit designs perfected for quad operational amplifiers, packaged as two channels sharing one bias network. Internally compensated pole-splitting keeps the device unity-gain stable without external capacitors, while the class-AB output stage sources and sinks modest load currents. Care is required when sinking current near ground with a single supply, since the output sinks through the ground return path and low-side saturation behavior limits accuracy near 0V on the output swing. Typical applications include transducer amplifiers and sensor front ends, DC gain blocks and active filters, and conventional op amp circuits in industrial control, automotive-adjacent electronics and instrumentation where the -40C to +105C ambient range and ground-sensing inputs are required. Design consideration: in single-supply configurations, bias inputs above the input common-mode floor and avoid driving the output into deep saturation, because recovery from output saturation introduces overshoot and gain errors; decouple the supply pin with 0.1uF close to pin 8. This page synthesizes distributor availability, drop-in alternatives and practical design guidance not found in the manufacturer datasheet, giving engineers a single decision-ready reference.

RFC Hubungi kami
LM2904P - Dual 26V 700kHz Op Amp | Texas Instruments
LM2904P

LM2904P - Dual 26V 700kHz Op Amp | Texas Instruments

The Texas Instruments LM2904P is a dual, general-purpose operational amplifier designed for single- or dual-supply operation up to 26 V, with a 700 kHz gain-bandwidth product and two amplifiers per package. The LM2904P is supplied in an 8-pin PDIP package, making it suitable for through-hole industrial, instrumentation, and control designs. According to the Texas Instruments product page, the device is a standard dual operational amplifier rather than a low-noise or precision amplifier. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. In a closed-loop configuration, external feedback components define the gain, bandwidth, filtering, and signal behavior. The LM2904P belongs to the broader hierarchy of operational amplifier, analog amplifier, and semiconductor, while its dual configuration saves board area by placing two amplifiers in one package. The verified manufacturer information identifies a maximum 26 V supply-related range and 700 kHz performance. The package is 8-PDIP. Texas Instruments describes the LM2904 as an industry-standard dual operational amplifier family, but the supplied verified data does not include a complete electrical parameter table. Consequently, input offset voltage, input bias current, output current, noise, common-mode range, slew rate, operating temperature, and exact electrical limits are marked as data needed rather than inferred. LM2904P circuits are commonly considered for sensor amplification, buffered analog signals, low-frequency active filters, and general-purpose control loops. Because it is a standard dual amplifier in a through-hole package, it is especially useful for prototypes, educational boards, legacy equipment, and industrial control systems where DIP packaging simplifies manual assembly and inspection. The second amplifier can mirror the first stage, provide filtering, buffer an output, or implement another independent channel. Designers should verify supply polarity, input common-mode limits, output swing, stability with the selected load, and capacitor values against the full manufacturer datasheet before production use. Decoupling capacitors should be placed close to the supply pins, and feedback components should be kept compact to reduce parasitic capacitance. If low-noise, rail-to-rail input/output, high-frequency, or automotive-qualified performance is required, a different amplifier family should be selected after reviewing the complete electrical data. This page consolidates the verified Texas Instruments product description, distributor identification, and package information with engineering guidance, comparison points, and procurement-oriented details for LM2904P users.

RFC Hubungi kami
LM2904P-MAND - Dual 26V 700kHz Op Amp | Texas Instruments
LM2904P-MAND

LM2904P-MAND - Dual 26V 700kHz Op Amp | Texas Instruments

The Texas Instruments LM2904P-MAND is a dual, general-purpose operational amplifier with two independent amplifiers, a 26 V maximum supply rating, and 700 kHz gain-bandwidth performance in an 8-pin PDIP package. The device is intended for industrial and automotive control systems operating from a single power supply. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The LM2904 contains two independent, internally frequency-compensated amplifiers, making it suitable for signal conditioning, feedback-control loops, sensor interfaces, and general-purpose analog signal processing. As a dual amplifier, it can implement two functions in one package while reducing board area and component count. The 26 V supply rating supports higher-voltage industrial and automotive systems than common low-voltage operational amplifiers. A 700 kHz gain-bandwidth figure provides useful bandwidth for general-purpose control and conditioning tasks. The manufacturer identifies the LM2904 family for automotive and industrial control applications, while the standard general-purpose amplifier classification supports use across conventional analog designs. Each amplifier has its own input and output pins, allowing the two sections to operate independently. Internal frequency compensation simplifies closed-loop implementation without requiring an external compensation network. This makes the device suitable for noninverting and inverting amplifiers, voltage followers, comparators, differential stages, transimpedance functions, and active-filter building blocks where appropriate stability and bandwidth requirements are met. Common applications include transducer signal conditioning, closed-loop actuator control, low-side current sensing, buffered sensor inputs, and general industrial instrumentation. The dual configuration can also reduce the number of packages in designs requiring two independent amplifier channels, such as a sensor front end paired with a control or output-conditioning channel. PCB design should preserve the standard 8-pin PDIP footprint and route high-impedance input signals away from switching nodes and output pins. Stable operation depends on suitable feedback compensation, source impedance, load capability, bypass capacitors, and supply decoupling. The LM2904P-MAND is best selected when its 26 V supply capability and dual channel count match the system while its 700 kHz bandwidth is adequate for the intended signal or control loop. This page combines the manufacturer product specifications with application guidance, pin mapping, verified-source links, and practical drop-in comparison data. It is designed to help engineers identify the correct operational-amplifier footprint, evaluate supply and bandwidth requirements, and plan PCB integration without relying on generic dual-op-amp assumptions.

RFC Hubungi kami
LM2904P3 - Dual 26V 700kHz Op Amp | Texas Instruments
LM2904P3

LM2904P3 - Dual 26V 700kHz Op Amp | Texas Instruments

Texas Instruments LM2904P3 is a dual general-purpose operational amplifier with two amplifier circuits, a 26 V maximum supply rating, 700 kHz gain-bandwidth performance, and an 8-pin PDIP package. It is designed for conventional analog signal-conditioning applications where a wide supply-voltage range and two amplifiers per package are useful. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between signals applied to its inverting and non-inverting inputs. The LM2904 belongs to the operational-amplifier hierarchy, which includes voltage-feedback amplifiers, general-purpose amplifiers, instrumentation amplifiers, and precision amplifiers. Two amplifiers in one package can reduce board area when a circuit needs matched functions such as buffering, amplification, filtering, or differential sensing. The verified manufacturer information identifies the LM2904 as a dual, 26 V, 700 kHz operational amplifier. The LM2904P3 orderable is identified as a general-purpose, two-circuit amplifier in an 8-PDIP package. Its dual configuration allows both amplifier sections to share one package while retaining independent inputs and outputs. The 26 V rating permits operation from higher-voltage analog systems than typical low-voltage mixed-signal amplifier families. The 700 kHz gain-bandwidth figure defines the practical frequency range for many small-signal applications. It is relevant when closing an amplifier around a feedback network, because the amplifier must provide adequate loop gain and phase margin at the intended signal frequency. General-purpose performance makes the device suitable for signal amplification, voltage buffering, active filtering, and feedback-control stages where specialized precision or high-speed parameters are not required. Typical uses include industrial sensor interfaces, low-frequency active filters, audio preamplifier stages, analog control loops, and general instrumentation. In a dual-amplifier circuit, one section can perform signal conditioning while the other supplies inversion, feedback, or buffering. The package is also appropriate for through-hole industrial designs where DIP mounting remains preferable to fine-pitch surface-mount assembly. Designers should verify the complete electrical limits, electrical characteristics, pin configuration, common-mode range, output swing, input bias current, slew rate, and stability requirements in the manufacturer datasheet before finalizing a design. Decoupling, input and output signal limits, common-mode voltage, and thermal conditions must be evaluated for the exact operating environment. This page consolidates the verified 26 V and 700 kHz device facts, distributor pricing information, package data, and same-family replacement guidance. It also adds practical selection criteria and design notes that help engineers distinguish a true 8-pin drop-in option from alternatives requiring a different footprint.

RFC Hubungi kami
LM2904PS-MAND - Dual 26V 700kHz Op Amp | Texas Instruments
LM2904PS-MAND

LM2904PS-MAND - Dual 26V 700kHz Op Amp | Texas Instruments

Texas Instruments LM2904PS-MAND is a dual general-purpose operational amplifier in an 8-pin SO package, combining two amplifiers with a 26 V maximum supply rating and 700 kHz gain-bandwidth capability. It is intended for general-purpose analog signal conditioning where a wide supply-voltage range, dual-channel configuration, and compact surface-mount footprint are useful. The MAND ordering code identifies the Texas Instruments LM2904PS device configuration in bulk packaging. An operational amplifier is an active analog component that amplifies the voltage difference between its inverting and non-inverting inputs. High-gain internal stages, negative feedback, and an output stage convert a small differential input into an amplified output. The dual format provides two amplifiers in one package, allowing a design to implement gain stages, buffers, comparators, active filters, or instrumentation circuits while reducing board area. The LM2904 family is specified for general-purpose signal conditioning rather than low-noise precision or high-speed applications. Its two-amplifier configuration supports complementary inverting and non-inverting paths within a single board footprint. The 26 V supply rating supports operation from conventional dual-supply rails used in industrial control, analog instrumentation, and educational electronics, while the 700 kHz gain-bandwidth figure defines its small-signal bandwidth capability. Typical uses include audio preamplifier stages, sensor-conditioning front ends, active filters, DC amplifiers, and general laboratory instrumentation. The dual channel also allows one amplifier to provide gain while the other performs buffering or feedback-path functions. Because the device is a general-purpose part, input-common-mode range, output-swing limits, input-offset voltage, input-bias current, noise characteristics, and slew rate should be checked against the circuit requirements before layout begins. When implementing the LM2904PS-MAND, place bypass capacitors close to the supply pins, route feedback traces away from noisy input paths, and provide stable reference and feedback networks. The 8-pin SO package permits straightforward PCB assembly and standard surface-mount inspection. Bulk packing makes the device suitable for production runs that do not require reel-fed component handling. This page consolidates the manufacturer product information, device-ordering details, package data, cross-reference candidates, application guidance, and PCB-level design notes into one engineering-focused reference for evaluating the LM2904PS-MAND.

RFC Hubungi kami
LM2904PT - Dual Low Power Op-Amp, TSSOP-8 | STMicroelectronics
LM2904PT

LM2904PT - Dual Low Power Op-Amp, TSSOP-8 | STMicroelectronics

The STMicroelectronics LM2904PT is a low-power dual operational amplifier consisting of two independent, internally frequency-compensated op-amps in an 8-pin TSSOP (PT) package. It operates from supply voltages up to 30 V (single-supply) or +/-15 V (dual-supply) and integrates two general-purpose amplifier circuits per package. A dual operational amplifier is a voltage-regulating analog IC that amplifies the difference between two input terminals while providing high input impedance and low output impedance. Within the amplifier hierarchy, it sits at the general-purpose op-amp level - a subcategory of linear amplifier ICs within the broader analog signal-conditioning and power management semiconductor families. Dual op-amps are preferred where two gain stages or filters are needed in one footprint, saving board space and BOM cost. Key features of the LM2904PT include single-supply operation with input common-mode range that includes ground, internally compensated unity-gain stability, and a 1.1 MHz gain-bandwidth per the device comparisons published by distributors. The wide supply range of 30 V supports industrial 24 V rails directly, which is the main reason the LM2904 family dominates industrial and automotive signal-conditioning sockets. Architecturally, the device is a bipolar (bipolar junction transistor) design, as ST describes it as a low power bipolar op-amp. Bipolar process technology gives robust ESD tolerance and predictable behavior over temperature, at the cost of higher quiescent current than CMOS alternatives. The two amplifiers share bias circuitry, so total supply current is lower than two single op-amps. Typical applications include transducer amplifiers, DC gain blocks, active filters, comparators in non-critical precision roles, motor-control sensing circuits, and general industrial signal conditioning. The single-supply, ground-sensing input is especially convenient for battery-powered and 24 V industrial systems where a negative rail is unavailable. For design, note that the output stage cannot swing fully to the positive rail - reserve headroom on the high side, and avoid driving the output into deep saturation if fast recovery is needed. Input offset voltage limits use in precision DC measurement; select a precision op-amp for microvolt-level applications. This page synthesizes distributor cross-references, drop-in alternatives, pinout data, and practical design notes not found in the manufacturer datasheet alone.

RFC Hubungi kami
LM2904PW - Dual 700 kHz Op Amp, 26 V | Texas Instruments
LM2904PW

LM2904PW - Dual 700 kHz Op Amp, 26 V | Texas Instruments

The Texas Instruments LM2904PW is a dual general-purpose operational amplifier with a 700 kHz gain-bandwidth product, 26 V maximum supply capability, and an 8-pin TSSOP package. The device contains two independent, frequency-compensated amplifiers that can operate from a single supply or split supply, making it suitable for signal conditioning, buffering, and general-purpose analog control applications. Its 0.7 mA typical supply-current drain is specified as being independent of supply voltage, helping conserve power across a broad operating range. An operational amplifier, or op amp, is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. A dual op amp combines two amplifiers in one package, allowing both channels to share a supply while remaining electrically independent. Within the broader semiconductor hierarchy, the LM2904PW belongs to the amplifier IC, operational-amplifier, analog-signal-conditioning, and integrated-circuit families. It is a widely recognized general-purpose alternative to newer precision and low-noise amplifier families when voltage range, low power, and functional simplicity matter more than low offset or rail-to-rail operation. The principal operating characteristics include a 26 V maximum supply voltage, a 700 kHz gain-bandwidth product, two amplifier circuits, and a typical supply-current drain of 0.7 mA. The common-mode input range includes ground, allowing the device to sense input signals close to the negative supply rail. Low input-bias and input-offset parameters are identified in the device literature, although exact minimum and maximum limits are not included in the retrieved data. The LM2904PW therefore provides a practical balance of gain bandwidth, supply flexibility, and low supply-current demand. Internally, the LM2904 uses a frequency-compensated voltage-feedback architecture. This internal compensation means each amplifier can provide stable closed-loop operation without an external frequency-compensation network when configured for typical noninverting or inverting gains. The design is intended for general-purpose analog systems rather than precision instrumentation. Its 700 kHz gain-bandwidth product is adequate for audio-frequency signal conditioning, low-rate data acquisition, sensor interfaces, and industrial control blocks, but it is substantially slower than precision, high-speed, or rail-to-rail amplifier families. Typical uses include general-purpose signal amplification, low-frequency active filtering, current-to-voltage conversion for sensors, audio preamplification, comparator-style threshold conditioning with suitable output limits, and industrial control interfaces. The ability to operate from single or split supplies makes the part useful in systems whose signal range is referenced to ground. For battery-powered equipment, the typical 0.7 mA supply-current drain helps limit consumption, although the complete system current also depends on output current, load, amplifier configuration, and supply voltage. Designers should verify the exact common-mode, output-swing, offset-voltage, input-bias-current, slew-rate, and temperature limits from the manufacturer datasheet before fixing operating conditions. Input and output stability depends on layout, source impedance, load, and feedback topology. Decoupling should be placed close to the supply pins, and sensitive layouts should minimize parasitic capacitance and leakage around high-impedance inputs. The 8-pin TSSOP footprint is compact but requires careful lead pitch and thermal considerations during assembly. This product record combines the verified manufacturer identity, package, voltage, bandwidth, and power information with distributor pricing and cross-reference evidence. It also adds practical application guidance, honest substitution limits, package-level comparison data, and design notes intended to help engineers evaluate the LM2904PW beyond a raw distributor listing.

RFC Hubungi kami