LM2904MWC - Dual 26V 700kHz Operational Amplifier | Texas Instruments
MPN: LM2904MWC ✓ AktifLM2904MWC Ringkasan
An operational amplifier is an analog integrated circuit that amplifies the difference between its two input voltages. The LM2904 belongs to the operational-amplifier hierarchy within analog signal-processing ICs, where general-purpose devices are used for buffering, amplification, comparisons, filtering, instrumentation, and control loops. The two channels in the LM2904 can operate independently, allowing one device to implement two analog functions while conserving board area.
The 700 kHz gain-bandwidth product makes the LM2904 appropriate for general-purpose signal conditioning rather than high-speed precision signal chains. Its 26 V supply capability is useful in industrial, automotive, and communications equipment where the circuit must tolerate higher supply rails than a conventional low-voltage amplifier. Because it is a general-purpose dual amplifier, designers can use the two channels for functions such as noninverting and inverting gain stages, buffers, active filters, comparators, and sensor-conditioning stages.
The LM2904MWC is identified as a wafer sale rather than a finished surface-mount component. Wafer-level procurement is normally used by semiconductor manufacturers, test houses, and automated assembly operations that perform die-level inspection, final test, packaging, and board assembly. In such a process, manufacturing controls, known-good-die requirements, assembly yield, and lot traceability become as important as the electrical characteristics of the amplifier itself.
Typical circuit roles include amplifying low-frequency sensor signals, buffering inputs to analog-to-digital converters, implementing active low-pass filters, and driving slow-changing control signals. The dual-channel organization is especially useful when a board requires two similar analog functions, such as an input stage and an output buffer. Decoupling capacitors should be placed close to the device supply pins, while input and output routing should be kept short and away from high-current switching paths.
Because LM2904MWC is supplied as a wafer, engineers must confirm the die orientation, pin identification, tested temperature grade, quality level, and packaging flow before committing it to a manufacturing process. The official Texas Instruments LM2904 product page provides the authoritative ordering and technical information, while the manufacturer datasheet defines electrical characteristics, test conditions, and pin functions.
This page organizes the confirmed LM2904MWC identity, package format, electrical headline parameters, engineering applications, and verified cross-reference landscape. It also distinguishes a directly replaceable drop-in option from related amplifier families that may require different packages, pin assignments, or performance validation.
Pilihan pengganti yang segera untuk LM2904MWC — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Tiada pilihan pengganti yang segera untuk produk ini.
Minta AlternatifLM2904MWC Penilaian maksimum & Ciri-ciri Elektrik
| Amplifier Type | General-purpose operational amplifier |
| Number of Channels | 2 circuits |
| Maximum Supply Voltage | 26 V |
| Gain-Bandwidth Product | 700 kHz |
| Delivery Format | Wafer |
| Supplier | Texas Instruments |
Panduan Konfigurasi Pin LM2904MWC standard
Konfigurasi pin untuk LM2904MWC (standard pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.
Tiada data garisan pin yang diperoleh untuk LM2904MWC.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
LM2904MWC patut untuk 6 aplikasis: Industrial Sensor Signal Conditioning, Active Low-Pass Filtering, ADC Input Buffering, Process Control Amplification, Communication Interface Buffering, Power Supply Feedback Amplifier.
Industrial Sensor Signal Conditioning
The LM2904MWC fits general-purpose industrial sensor-conditioning circuits when the signal bandwidth remains within the device's 700 kHz gain-bandwidth capability. Its two amplifier channels can provide gain and buffering for low-frequency sensor outputs while operating from supply rails up to 26 V. The wafer format is appropriate for manufacturing organizations with established die-handling and packaging processes. Design work should include offset, bias-current, common-mode-range, and noise checks using the manufacturer electrical tables, while the PCB should provide local supply bypassing and a low-impedance return path.
Active Low-Pass Filtering
The dual LM2904MWC can implement two active low-pass filter sections for low-frequency measurement, control, or instrumentation systems. A 700 kHz gain-bandwidth product leaves usable closed-loop bandwidth below the device's unity-gain frequency, while the 26 V supply rating accommodates higher-rail analog systems. The two channels may be cascaded, used for separate channels, or assigned to a filter and a buffer. Component selection should preserve suitable noise and gain error behavior over the intended frequency range, and prototype boards should isolate sensitive input nodes from switching circuitry.
ADC Input Buffering
The LM2904MWC can buffer a sensor or transducer output before conversion by an analog-to-digital converter, provided the 700 kHz gain-bandwidth product satisfies the required settling behavior. Using both channels can support two buffered inputs or one differential signal path with an additional feedback network. The 26 V maximum supply rating supports systems that share a higher analog rail, although the complete input common-mode range must remain valid. Decoupling capacitors should be placed at the wafer-assembled supply connections, and sensitive routes should remain short, shielded from switching nodes, and referenced to a quiet ground plane.
Process Control Amplification
The LM2904MWC is applicable to slow process-control loops where a controller compares a sensed process value against a reference and generates an analog actuator command. One channel can amplify the sensor signal while the other handles reference or drive conditioning, helping reduce the component count. The device's 700 kHz gain-bandwidth product is more than adequate for many thermal, pressure, and level-control loops, while its 26 V rating permits higher-voltage control interfaces. Loop stability, output swing, common-mode limits, and transient response must be evaluated in the final circuit.
Communication Interface Buffering
The LM2904MWC can condition low-frequency communication, receiver, or line-interface signals in equipment using higher-voltage analog rails. The dual-channel format supports independent transmit and receive buffering, while the 700 kHz gain-bandwidth product suits moderate-bandwidth baseband functions rather than high-speed data lines. The 26 V supply rating is useful where legacy interface circuits operate above low-voltage logic levels. Designers should verify input common-mode range, output swing, slew rate, noise, and stability at the intended closed-loop gain before using the device in a new communication design.
Power Supply Feedback Amplifier
The LM2904MWC can amplify the error voltage in a linear-regulator feedback path where the operating band is well below 700 kHz. Its two channels can support redundant sensing, a feedback amplifier plus an auxiliary signal path, or one channel in each of two related rails. The 26 V supply capability can align with higher-voltage analog power systems, but the output must remain within the amplifier's swing limits under worst-case error conditions. Compensation components should be derived from the complete power-stage transfer function, and layout should minimize feedback-route pickup from power switching nodes.
Data referensi kejuruteraan untuk LM2904MWC — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Penyeberangsung Jelas
- Higher-voltage general-purpose dual-amplifier positioning (vsLM2904LV)
- Dual-channel integration in one die (vsLM2904B)
- General-purpose 700 kHz bandwidth (vsLM2904B)
Catatan Desain
Do not treat LM2904MWC as a finished-package component. The MWC ordering code identifies a wafer-sale configuration, so a conventional IC land pattern is not applicable. Confirm die orientation, pin mapping, temperature grade, tested status, assembly method, and lot traceability with the manufacturer before creating production tooling. Related LM2904 devices in SOIC or other packages can differ in ordering code, assembly process, and procurement conditions.
Treat the wafer-level assembly as a mixed-signal layout problem even though the amplifier itself is not a high-speed device. Provide local supply bypassing close to the assembled power pins, use a continuous or carefully partitioned ground plane, and keep noninverting inputs away from switching nodes. Because the wafer is packaged later, preserve access for die inspection and verify electrical continuity before the package is committed to a multichannel PCB assembly.
Design the power rails around the confirmed 26 V maximum supply rating, including tolerance, transients, and startup conditions. Do not interpret that value as permission to operate indefinitely at 26 V; the manufacturer electrical tables define the safe operating combinations. For a dual amplifier, calculate supply-current demand for both channels and ensure the regulator has adequate transient capability for the complete analog load.
Use closed-loop gains that preserve adequate stability and bandwidth with the LM2904's 700 kHz gain-bandwidth product. Keep feedback components close to the assembled amplifier pins, avoid long high-impedance input traces, and place input-biasing resistors where their thermal effects can be minimized. Validate the final board at the intended gain because parasitic capacitance on a wafer-assembled footprint can alter compensation and settling behavior.
Maklumat Kesediaan
The manufacturer product page and distributor snippets do not state the requested compliance status for the exact LM2904MWC wafer ordering code. A wafer-sale part should not inherit compliance assumptions automatically from a finished-package ordering option.