Produk (44,000+)

MAX3243ECRHBR - 3/5 RS-232 Transceiver, 500kbps, 32-VQFN | TI
MAX3243ECRHBR

MAX3243ECRHBR - 3/5 RS-232 Transceiver, 500kbps, 32-VQFN | TI

The Texas Instruments MAX3243ECRHBR is a 3 V to 5.5 V multichannel RS-232 line driver/receiver IC providing three drivers, five receivers, and a dual charge-pump supply in a 32-pin VQFN (5 mm x 5 mm) surface-mount package. It supports data rates up to 500 kbps and is qualified for operation from 0 °C to 70 °C. An RS-232 transceiver is a bidirectional interface IC that converts logic-level TTL/CMOS signals into RS-232 level voltages on transmit and back into logic levels on receive. Within the power-management and interface hierarchy, the MAX3243E family sits at the physical-layer boundary between a host UART and a cable-attached peripheral, adding level translation, noise immunity, and electrostatic-discharge (ESD) hardening that a bare UART driver pair cannot provide. Key features of the MAX3243ECRHBR include ±15 kV ESD protection on all serial pins under the human body model (HBM), ±15 kV air-gap and ±8 kV contact discharge per IEC 61000-4-2, a dual on-chip charge pump that generates the bipolar RS-232 levels from a single supply, and a 3-to-5.5 V operating range that allows direct interfacing with 3.3 V and 5 V host logic without level shifters. A single-channel shutdown pin places the device in a low-power state when the port is idle. Architecturally, the device splits its channels asymmetrically: three drivers share the charge-pump rails for a typical transmit group, while five receivers provide more receive inputs than there are transmit outputs. This suits equipment where the host must listen to several peripherals but only drives one or two lines, such as multi-drop industrial terminals and POS equipment. The wide common-mode range of the receivers allows them to interpret RS-232 signals referenced to ground even when the two ends of a long cable sit at different ground potentials. Typical applications include industrial serial consoles, barcode scanners, weighing scales, laboratory instrument control ports, point-of-sale terminals, and battery-powered handheld peripherals that still require a hardened RS-232 port. The small 5 mm square VQFN footprint also makes the device attractive for space-constrained handheld and portable designs where a TSSOP would be too long for the board outline. When laying out this device, place the charge-pump flying capacitors and the RS-232 line-side protection network close to the device, and route the driver outputs directly to the connector with a common-ground return path. Use the pin-description table in the manufacturer datasheet to assign logic-side and line-side nets, and confirm the VQFN exposed-pad soldering and thermal requirements in the package drawing section.

RFC Hubungi kami
MAX3243ECUI+ 3V 5.5V 250kbps RS-232 Transceiver | ADI
MAX3243ECUI+

MAX3243ECUI+ 3V 5.5V 250kbps RS-232 Transceiver | ADI

Analog Devices MAX3243ECUI+ is a 3-to-5.5 V RS-232 transceiver with three transmitter channels, five receiver channels, 250 kbps data rate, ±15 kV ESD protection, and automatic shutdown in a 28-pin TSSOP package. The part is designed for equipment that requires multiple RS-232 ports while operating from either 3 V or 5.5 V supplies. An RS-232 transceiver is a line-driver and line-receiver interface IC that converts low-voltage digital logic signals into RS-232 voltage levels and converts incoming RS-232 signals back into logic-compatible levels. In the interface hierarchy, the MAX3243ECUI+ belongs to the communication-interface IC family, combining RS-232 drivers and receivers with low-voltage digital support and protected external connections. Key electrical features include operation from 3.0 V to 5.5 V, a maximum data rate of 250 kbps, and ±15 kV ESD protection on the serial interfaces. Automatic shutdown reduces supply consumption when the associated RS-232 links are inactive, while the complementary always-active receiver supports continuous monitoring. The 28-pin TSSOP package provides a compact surface-mount footprint for industrial control, communications, instrumentation, and embedded equipment. The three drivers accommodate outbound serial connections, while five receivers provide additional inbound monitoring channels. This asymmetric 3/5 arrangement is useful in systems where several remote devices report status to one controller while the controller drives a smaller number of commands. The 250 kbps maximum data rate supports moderate-speed point-to-point serial links and legacy peripheral communication. Typical uses include industrial controllers, data-acquisition equipment, POS terminals, test systems, and service interfaces. In an industrial controller, the device can connect a local processor to multiple RS-232 sensors or service ports while its ESD-protected lines improve resilience to electrostatic discharge encountered during installation and maintenance. PCB design should place the device close to its RS-232 connector and route driver and receiver traces away from clocks, switching regulators, and high-speed digital signals. Confirm that connector-side protection and grounding provide the intended surge and ESD path, and follow the manufacturer datasheet for recommended charge-pump capacitors and layout. This page combines the manufacturer specifications, package details, engineering applications, drop-in alternatives, comparison parameters, and practical design guidance to help engineers evaluate the MAX3243ECUI+ for new and existing RS-232 designs.

RFC Hubungi kami
MAX3243ECUI+T - 3/5 RS-232 Transceiver | Analog Devices
MAX3243ECUI+T

MAX3243ECUI+T - 3/5 RS-232 Transceiver | Analog Devices

Analog Devices MAX3243ECUI+T is a 3-driver, 5-receiver RS-232 transceiver with a 250 kbps data rate, 3.0 V to 5.5 V supply range, ±15 kV ESD protection, and a 28-pin TSSOP package. It combines three transmit channels, five receive channels, low-power AutoShutdown, and supply current as low as 1 µA for portable and industrial serial-interface designs. An RS-232 transceiver is an interface IC that converts logic-level UART signals into RS-232 line levels and converts incoming RS-232 signals back into CMOS-compatible logic. In the product hierarchy, the MAX3243 belongs to the RS-232 transceiver class, then to line-driver and receiver ICs, then to interface ICs and semiconductors. This multi-channel device reduces the number of discrete interface packages required when several serial ports share one controller. The MAX3243 operates from 3.0 V to 5.5 V, allowing operation from either 3.3 V or 5 V system rails. Its three drivers and five receivers support asymmetric port counts common in console, diagnostic, instrumentation, and embedded-control equipment. AutoShutdown disables the internal supply and drivers when the receiver inputs do not detect a valid signal level, reducing standby consumption to approximately 1 µA when supported by the selected power configuration. The interface provides ±15 kV ESD protection according to the device description, improving tolerance to electrostatic discharge at externally accessible serial connectors. The 250 kbps maximum signaling rate is suitable for legacy RS-232 equipment, industrial consoles, configuration ports, and control links that do not require the throughput of modern differential interfaces. Charge-pump circuitry generates the bipolar voltage required by RS-232 without a separate negative supply. Typical uses include three-port RS-232 console expansion, multi-channel data acquisition, service interfaces in industrial equipment, instrument control ports, and mixed-voltage embedded systems. The 28-pin TSSOP package supports compact surface-mount layouts while providing enough I/O for five receive inputs, three transmit outputs, power, ground, and control functions. PCB design should keep charge-pump capacitors close to their associated pins and route driver outputs and receiver inputs away from sensitive analog circuitry. External protection may still be required for long cables or connectors exposed to severe industrial transients. The receiver inputs should also be checked against the selected operating mode and shutdown behavior before finalizing the system power architecture. This page combines manufacturer specifications, package and interface details, drop-in family options, application guidance, and practical PCB considerations to support faster component selection and replacement planning.

RFC Hubungi kami
MAX3243ECWI+ - 3V to 5.5V RS-232 Transceiver | Maxim
MAX3243ECWI+

MAX3243ECWI+ - 3V to 5.5V RS-232 Transceiver | Maxim

The Maxim Integrated MAX3243ECWI+ is a 3V to 5.5V RS-232 transceiver with three transmitters, five receivers, full-duplex operation, and 15 kV ESD protection, housed in a 28-pin SOIC package. It is designed for systems that require multiple RS-232 data channels and low-power operation from a single 3.0V or 5.0V supply. An RS-232 transceiver is an interface IC that combines line drivers, also called transmitters, and line receivers. The MAX3243 family provides three driver outputs and five receiver inputs in one package, allowing several serial ports or multiple logic signals to share a compact RS-232 interface. The MAX3243ECWI+ is intended for industrial, instrumentation, communications, and embedded-control equipment. Key features include a 3.0V to 5.5V operating supply range, 1 uA supply current in shutdown mode, 120 kb/s data-rate capability in the comparison data, and integrated ESD protection rated to 15 kV. AutoShutdown functionality helps reduce system power consumption when the RS-232 interface is not required. The 28-pin SOIC package is a standard surface-mount industrial package. The device uses RS-232 line signaling to translate digital logic levels into differential bipolar voltage levels and back again. The three transmitters support point-to-point serial links, while the five receivers can monitor incoming data or accept additional RS-232 signals. The integrated protection circuitry is particularly useful in industrial environments where cable-connected ports can be exposed to electrostatic discharge. Typical applications include multi-port RS-232 equipment, test and measurement instruments, data acquisition systems, industrial controllers, and embedded serial interfaces. The MAX3243ECWI+ is appropriate when one board needs more than a single RS-232 transmitter and receiver while keeping the power supply below 5.5V. For implementation, verify the supply voltage, confirm that the transceiver is enabled or disabled according to the system power sequence, and provide the required external charge-pump capacitors recommended by the manufacturer datasheet. Place protection and signal-routing components close to the connector and the transceiver to minimize ESD current paths.

RFC Hubungi kami
MAX3243ECWI+T - 3/5 RS-232 Transceiver, 250 kbps | Analog Devices
MAX3243ECWI+T

MAX3243ECWI+T - 3/5 RS-232 Transceiver, 250 kbps | Analog Devices

The Analog Devices MAX3243ECWI+T is a 3/5 RS-232 transceiver with three drivers, three receivers, and 250 kbps signaling in a 28-SOIC package. It operates from 3.0 V to 5.5 V, provides ±15 kV ESD protection, and supports automatic shutdown to reduce supply current to 1 µA when no valid receiver signal is detected. AutoShutdown circuitry wakes the device when valid RS-232 activity resumes. An RS-232 transceiver is an interface IC that converts logic-level UART signals into RS-232 line levels and converts incoming RS-232 signals back into CMOS-compatible logic. The MAX3243 belongs to the RS-232 interface transceiver class, combining drivers, receivers, charge-pump support, and low-power management in one device. This integration allows a host controller or test system to communicate with RS-232 equipment over a cable-defined serial interface. Key features include a 3.0 V to 5.5 V supply range, operation up to 250 kbps, full-duplex communication through three transmit and three receive channels, and ±15 kV ESD protection. The 1 µA shutdown supply current helps preserve system energy when the port is idle. The wide 28-SOIC footprint is a practical option for designs requiring more channels than the smaller two- or three-driver transceivers commonly used in compact equipment. The MAX3243 architecture uses integrated level-shifting drivers and receivers to produce and accept RS-232-compatible signal levels from a low-voltage digital supply. Charge-pump circuitry provides the elevated transmitter voltage required by the RS-232 standard. AutoShutdown reduces power consumption when the connected port carries no valid activity, while receiver-side logic allows the host to recognize a returning signal and reactivate the device. Typical uses include industrial serial consoles, automated test equipment, data acquisition systems, instrumentation, point-of-sale terminals, and legacy peripheral connectivity. The 250 kbps capability also suits short-distance board-level links, data acquisition links, and configuration interfaces where the nominal RS-232 limit is lower but faster burst traffic is expected. A critical design consideration is that RS-232 is a point-to-point interface, so each driver should face a single receiver rather than an unterminated multidrop bus. Place transient-protection and connection components where cables enter the enclosure, and confirm that signal levels, ground reference, and cable length satisfy the system communication requirements.

RFC Hubungi kami
MAX3243EEAI+ - 3.0V RS-232 Transceiver | Analog Devices
MAX3243EEAI+

MAX3243EEAI+ - 3.0V RS-232 Transceiver | Analog Devices

The Analog Devices MAX3243EEAI+ is a 3/5-channel RS-232 transceiver designed for full-duplex serial communication, with three drivers, five receivers, a 3.0V to 5.5V supply range, and a 250kbps data rate. The device is housed in a 28-pin SSOP package and includes enhanced 15kV ESD protection on its RS-232 pins. It also provides automatic shutdown and wake-up functions for reducing supply current in portable or intermittently connected systems. An RS-232 transceiver is an interface IC that converts between logic-level digital signals and differential bipolar RS-232 line levels. The MAX3243EEAI+ belongs to the RS-232 transceiver hierarchy, where it combines line drivers, line receivers, charge-pump circuitry, and logic-level control into one communication interface. Its receiver structure supports both an active-low shutdown control and an active-high enhanced-power-management input. Key features include three transmit channels, five receive channels, 250kbps operation, operation from 3.0V to 5.5V, and 15kV ESD protection. The multiple receiver count allows one transmit line to be monitored by several destinations, while the three driver outputs support connections to three RS-232 data buses. Automatic shutdown can reduce power consumption when the connected equipment is inactive. The MAX3243E uses charge-pump circuitry to generate the positive and negative voltage levels required by RS-232 from a single low-voltage supply. Its enhanced driver design can provide true RS-232 performance at low supply voltages without requiring a 5V-only source. The manufacturer describes the MAX3243E family as 3V-powered EIA/TIA-232 and V.28/V.24 communications interfaces with automatic shutdown, wake-up, high data rates, and enhanced ESD protection. Typical applications include industrial serial controllers, point-of-sale equipment, instrumentation, data-acquisition systems, and communication links between a host and peripheral devices. The three drivers and five receivers are particularly useful when one controller must interface with multiple downstream devices or when received data must be distributed to several logic inputs. For a new design, verify the exact pin functions, shutdown polarity, charge-pump capacitor values, and external communication-line requirements against the Analog Devices MAX3243E datasheet before layout. Keep the RS-232 connector-side traces away from sensitive analog and high-speed digital paths, and place the required charge-pump capacitors close to their specified pins. This product page combines the MAX3243EEAI+ ordering information, RS-232 interface characteristics, package details, compatible alternatives, and practical implementation guidance to support component selection and PCB design decisions.

RFC Hubungi kami
MAX3243EEAI+C9V - 250kbps RS-232 Transceiver | Analog Devices
MAX3243EEAI+C9V

MAX3243EEAI+C9V - 250kbps RS-232 Transceiver | Analog Devices

Analog Devices MAX3243EEAI+C9V is a 3/5 RS-232 transceiver with three drivers, five receivers, 3.0V to 5.5V operation, 250kbps data rate, and ±15kV ESD protection in a 28-SSOP package. It also provides 1µA automatic-shutdown operation for low-power serial-port designs. An RS-232 transceiver is an interface IC that combines line drivers and receivers for communicating between digital logic and a serial port using EIA/TIA-232 voltage levels. The MAX3243E family belongs to the transceiver hierarchy, with RS-232 interface ICs forming part of the broader communications-interface semiconductor category. Its three-driver, five-receiver arrangement supports complete serial-port signal paths while reducing the number of discrete interface components required. Key features include a 3.0V to 5.5V supply range, operation up to 250kbps, ±15kV ESD protection, and a low 1µA shutdown current. Automatic shutdown and wakeup help reduce system power when the serial interface is idle. The 28-pin SSOP package is suitable for compact industrial, embedded, instrumentation, and data-communications equipment where board area and standardized surface-mount assembly are important. The MAX3243E architecture uses charge-pump circuitry to generate the bipolar voltage levels required by RS-232 from a single low-voltage supply. Its three drivers and five receivers provide flexible channel allocation for PC-style serial ports. Two receiver outputs remain active during shutdown according to the family description, allowing selected incoming signals to be monitored without keeping the entire interface fully powered. Typical applications include industrial serial adapters, embedded control systems, point-of-sale equipment, test instruments, data-acquisition systems, and legacy peripheral connections. The 3.0V minimum supply allows operation alongside 3.3V system logic, while the 5.5V maximum supports 5V designs. System designers should still verify signal levels, capacitance, line loading, and timing against the particular channel configuration. For PCB implementation, place charge-pump capacitors and interface bypass capacitors close to their associated pins, keep the RS-232 connector-side traces away from sensitive analog and clock paths, and provide adequate return-current paths. Confirm the device's charge-pump capacitor values and stability requirements in the manufacturer datasheet before releasing the layout. This page organizes the key electrical characteristics, drop-in alternatives, application guidance, comparison data, and practical layout considerations needed to evaluate the MAX3243EEAI+C9V for a new RS-232 interface design.

RFC Hubungi kami
MAX3243EEAI+G071 - 250kbps RS-232 Transceiver | Analog Devices
MAX3243EEAI+G071

MAX3243EEAI+G071 - 250kbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3243EEAI+G071 is a 3.0V to 5.5V RS-232 interface transceiver with a 250kbps data rate, ±15kV ESD protection, and a 28-pin SSOP package. The MAX3243EEAI family combines four drivers and four receivers with automatic shutdown and wake-up capability for reliable, low-power serial communication. An RS-232 transceiver is an interface integrated circuit that converts logic-level UART signals into RS-232 voltage levels and converts incoming RS-232 signals back to logic levels. In the hierarchy of electronic components, it belongs to the interface IC class, specifically the RS-232 transceiver and communications-interface subcategory used to bridge modern digital logic with legacy serial-port equipment. The MAX3243EEAI+G071 operates from a 3.0V to 5.5V supply, supporting both modern 3.3V and 5V systems. Its maximum signaling rate is 250kbps, making it suitable for industrial control links, data acquisition equipment, POS terminals, and service interfaces that require dependable RS-232 communication. Enhanced electrostatic-discharge protection on the RS-232 pins improves resilience to cable-borne transients encountered outside the equipment enclosure. The device family includes automatic shutdown and wake-up functions. These features allow a system to reduce supply consumption when no RS-232 activity is present and restore operation when a valid signal returns. The design combines four transmit channels and four receive channels in one package, reducing board area compared with several smaller interface components while preserving individual channel control. Typical applications include industrial serial controllers, test and measurement instruments, barcode scanners, security equipment, and communication links between a host computer and peripheral equipment. The 250kbps capability supports higher-throughput legacy serial traffic than slower RS-232 transceivers while retaining the voltage-level conversion required by the EIA/TIA-232 interface. PCB design should place the charge-pump capacitors and RS-232 interface components close to their associated IC pins. Keep long RS-232 traces away from clocks, sensitive analog inputs, and switching-supply nodes. Confirm the external capacitor values, supply range, and charge-pump requirements in the manufacturer datasheet before releasing the PCB. This page consolidates the exact package, operating-voltage, data-rate, and ESD characteristics, then adds application guidance, practical layout notes, and qualified same-family drop-in options for engineers evaluating the MAX3243EEAI+G071 for an RS-232 interface design.

RFC Hubungi kami
MAX3243EEAI+G1Z - 250kbps RS-232 Transceiver | Maxim
MAX3243EEAI+G1Z

MAX3243EEAI+G1Z - 250kbps RS-232 Transceiver | Maxim

The Maxim Integrated MAX3243EEAI+G1Z is a 3-transmitter, 5-receiver RS-232 interface transceiver operating from 3.0 V to 5.5 V, with a maximum data rate of 250 kbps in a 28-pin SSOP package. It provides automatic shutdown and wake-up, low 1 µA supply current, and enhanced electrostatic-discharge protection. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 voltage levels and converts incoming RS-232 signals back into digital logic levels. It belongs to the serial-interface hierarchy: transceiver > RS-232 interface > communications interface > interface IC. This bidirectional signal-conditioning function allows equipment operating at different logic levels to communicate through the EIA/TIA-232 physical interface. The MAX3243EEAI+G1Z combines three driver outputs with five receiver inputs, supporting applications that need multiple receive channels and a smaller number of transmit channels. Its 3.0 V to 5.5 V supply range accommodates modern 3.3 V and 5 V digital systems. The 250 kbps maximum data rate is suitable for moderate-speed serial links, including embedded control, instrumentation, and industrial communications equipment. Automatic shutdown is a defining feature of the MAX3243E family. When no valid receiver signal is detected, the on-board power supply and drivers can shut down to reduce supply current to as little as 1 µA. Automatic wake-up reactivates the interface when valid data returns, reducing system power consumption without requiring host intervention. Enhanced ESD protection strengthens the interface against electrostatic discharge encountered during cable installation or industrial environments. According to the MAX3243EEAI data-sheet description, transmitter outputs and receiver inputs support ±15 kV air-gap discharge and ±8 kV contact-discharge protection. These ratings are relevant to external cable-facing pins and should be considered alongside normal board-layout and grounding practices. Typical uses include RS-232 links in industrial controllers, test equipment, data-acquisition systems, point-of-sale hardware, and embedded serial-port systems. The 28-pin SSOP package is compact, but its lead pitch and thermal behavior require careful PCB planning. Use the manufacturer pin-description table when assigning tracks and confirming the exposed-package or thermal details for the selected ordering code. This page combines the family-level electrical characteristics, exact package identification, sourcing guidance, application fit, and practical design considerations. It also identifies genuine same-family alternatives while making the differences between ordering variants explicit for engineering review.

RFC Hubungi kami
MAX3243EEAI+T - 3/5 RS-232 Transceiver, 3-5.5V | Analog Devices
MAX3243EEAI+T

MAX3243EEAI+T - 3/5 RS-232 Transceiver, 3-5.5V | Analog Devices

The Analog Devices MAX3243EEAI+T is a 3-driver, 5-receiver full-duplex RS-232 transceiver operating from 3 V to 5.5 V in a 28-pin SSOP package. It supports data rates up to 250 kbps, includes ±15 kV ESD protection, and draws approximately 1 µA when the AutoShutdown feature has disabled the on-board supply and drivers. An RS-232 transceiver is an interface integrated circuit that converts between single-ended RS-232 line signals and complementary TTL/CMOS logic levels. It belongs to the RS-232 interface transceiver class, within interface ICs and broader semiconductor communication devices. The MAX3243EEAI+T combines three RS-232 drivers and five receivers, including two always-active noninverting receiver outputs for monitoring external signals without waking the main supply section. Principal features include a single 3 V to 5.5 V supply operation, 250 kbps data-rate capability, enhanced electrostatic discharge protection on all transmitter outputs and receiver inputs, and automatic shutdown with automatic wakeup. These characteristics support portable equipment, industrial controllers, data-acquisition systems, and legacy peripheral interfaces that require a direct RS-232 connection. The MAX3243 family uses Maxim Integrated's AutoShutdown architecture to reduce supply consumption when no valid receiver activity is detected. Supply current falls to approximately 1 µA in the shutdown condition, while activity on a receiver input can reactivate the internal supply and drivers. This behavior is useful in battery-powered and intermittently connected systems where an idle RS-232 port should not continue consuming significant power. Typical uses include configuring an embedded controller for legacy printers, industrial instruments, point-of-sale equipment, and service-console connections. The three-driver arrangement supports multiple outbound RS-232 channels, while the five-receiver arrangement provides additional input and monitoring paths. Its 28-pin SSOP package also suits compact boards where connector protection and ESD resilience are important. Design with the MAX3243EEAI+T by following the manufacturer datasheet for charge-pump capacitor selection, receiver-input handling, and supply bypassing. Confirm that every connected driver output meets the intended RS-232 voltage swing and that unused inputs remain in a defined state. Protect externally accessible connectors with the device's ESD capability and route return paths away from sensitive analog or high-speed digital circuitry. This page combines manufacturer specifications, distributor availability references, family-level drop-in alternatives, and application-focused design guidance to support faster component evaluation. It also identifies the temperature-grade and package differences that must be reviewed before assigning an alternative part to an existing PCB.

RFC Hubungi kami
MAX3243EETI+ - 250kbps RS-232 IC | Texas Instruments
MAX3243EETI+

MAX3243EETI+ - 250kbps RS-232 IC | Texas Instruments

The Texas Instruments MAX3243EETI+ is a 3 V to 5.5 V multichannel RS-232 line driver and receiver rated for 250 kbps data rates, with ±15 kV ESD protection on its communication pins. The device is offered in a 28-terminal, no-lead square QCCN package and operates in the industrial temperature grade. A low 1 µA supply specification supports power-conscious serial-interface designs. An RS-232 transceiver is an interface IC that combines a line driver, line receiver, and charge-pump voltage conversion in one package. It translates logic-level signals from a host or embedded controller into RS-232 levels and converts received RS-232 signals back to logic levels. Within the broader hierarchy of interface ICs, a multichannel RS-232 transceiver reduces component count, board area, and external voltage-doubling circuitry in multi-port serial systems. The MAX3243EETI+ supports supply voltages from 3 V to 5.5 V, enabling operation in both 3.3 V and 5 V systems. Its 250 kbps maximum data rate suits industrial equipment, data-acquisition equipment, point-of-sale terminals, and instrument-control links. Integrated ±15 kV ESD protection helps protect the external serial interface from electrostatic discharge encountered during installation or connection to cables. The MAX3243 family provides multiple drivers and receivers for RS-232 communication. When using the charge-pump section, the required capacitor arrangement and bypass components should follow the manufacturer datasheet's recommended application circuit. The integrated converter is intended to generate the positive and negative voltages required by RS-232, while the driver and receiver sections perform level conversion and signal conditioning. Typical uses include industrial serial controllers, test equipment, security systems, medical-instrument interfaces, and point-of-sale hardware. The 250 kbps capability is suitable for links that are faster than legacy 9600-bit-per-second ports but do not require the throughput of a modern high-speed differential serial standard. Cable length and signal-integrity requirements should still be checked against the RS-232 electrical limits for the intended operating environment. Place the MAX3243EETI+ close to the connector-side transceiver circuitry, keep the charge-pump capacitor loops compact, and provide a low-impedance ground return for each interface. Confirm logic levels, timing, shutdown behavior, and unused-channel connections in the manufacturer datasheet before releasing the PCB layout. Industrial temperature-grade qualification should also be checked against the complete assembly's environmental requirements. This page consolidates the manufacturer's operating limits, package characteristics, comparison criteria, replacement guidance, and application-oriented design guidance into one engineering reference. It focuses on practical selection and integration decisions rather than repeating only the basic distributor catalog description.

RFC Hubungi kami
MAX3243EETI+T - 250kbps RS-232 Transceiver | Analog Devices
MAX3243EETI+T

MAX3243EETI+T - 250kbps RS-232 Transceiver | Analog Devices

Analog Devices MAX3243EETI+T is a 3-channel RS-232 line driver and receiver operating from a 3V to 5.5V supply at data rates up to 250kbps. The device provides ±15kV electrostatic-discharge protection and uses AutoShutdown to reduce supply current to 1µA when no valid receiver signal is present. It is packaged in a 28-terminal, no-lead square QFN package designated QCCN. A multi-channel RS-232 transceiver combines push-pull line drivers and receivers for bidirectional data transfer between a host and an external serial device. In the broader hierarchy, MAX3243EETI+T is an interface transceiver, an interface IC, and a semiconductor for establishing the physical signal layer required by RS-232 equipment. The AutoShutdown function is particularly useful in battery-powered instruments, portable test equipment, and systems where an inactive serial port must not continue consuming power. The 3V to 5.5V operating range permits operation from both 3.3V and 5V system rails. Its 250kbps maximum signaling rate supports data rates above the traditional 20kbps RS-232 limit while remaining suitable for instrument control, point-of-sale equipment, industrial controllers, and embedded peripheral links. ±15kV ESD protection improves tolerance of connector-borne transients, although it does not eliminate the need for correct board layout and external protection strategy. The MAX3243 family combines low-power supply design with multiple driver and receiver channels. AutoShutdown detects whether valid signal levels appear on receiver inputs and disables the internal supply and drivers when the port is idle. This behavior allows a direct interface to operate from modern low-voltage digital rails without requiring a separate power-control transistor. The exact charge-pump, driver-slew, and receiver-threshold details should be confirmed against the manufacturer datasheet before finalizing a new design. Typical uses include multichannel instrument-control links, data acquisition, barcode and point-of-sale terminals, industrial serial adapters, and embedded systems that exchange RS-232 data with legacy peripherals. The 28-terminal QFN footprint also requires careful PCB planning because its compact leadless geometry leaves less visible inspection area and demands accurate land patterns, solder-paste control, and thermal-via placement. For a robust implementation, keep the MAX3243EETI+T close to the RS-232 connector, route driver and receiver traces away from sensitive analog circuitry, and place charge-pump and interface capacitors at the pins specified by the reference design. Confirm signal polarity, receiver thresholds, shutdown behavior, and grounding with the system-level RS-232 requirements rather than assuming that every ±15V RS-232-compatible product is electrically interchangeable. This page combines manufacturer specifications, package information, practical RS-232 design guidance, and carefully qualified same-family replacement options. It is intended to help engineers determine whether the MAX3243EETI+T fits the required voltage, data rate, channel count, package, and protection level before committing the part to a PCB or production BOM.

RFC Hubungi kami
MAX3243EETJ+ - 250kbps RS-232 Transceiver | Analog Devices
MAX3243EETJ+

MAX3243EETJ+ - 250kbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3243EETJ+ is a 3.0V to 5.5V RS-232 transceiver with three drivers and five receivers, automatic shutdown and wakeup, enhanced electrostatic-discharge protection, and a maximum data rate of 250kbps in a 32-pin TQFN package. The interface operates across -40°C to +85°C and provides ±15kV ESD protection. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 differential voltage levels and converts received RS-232 signals back into logic levels. The MAX3243E belongs to the broader hierarchy of interface ICs, serial transceivers, line drivers and receivers, and semiconductor communication components. Its multiple drivers and receivers allow several unidirectional or bidirectional serial links to share one compact device. Key features include three transmit outputs, five receive inputs, a 3.0V to 5.5V supply range, 1µA shutdown behavior, and automatic wakeup. The 250kbps maximum signaling rate supports data acquisition, industrial control, point-of-sale equipment, and embedded serial systems. A ±15kV ESD-rated interface helps protect equipment when connected cables are exposed to electrostatic discharge during installation or maintenance. The MAX3243E is designed for 3V-powered systems and uses automatic shutdown to reduce supply current when no valid signal is present. Automatic wakeup can return the transceiver to an operating state when incoming data resumes, reducing repeated manual enable control. Its three-driver and five-receiver arrangement provides more receive channels than the MAX3221E and MAX3223E family members, making it useful where several status or control signals must be monitored. Typical uses include industrial serial controllers, instrumentation, test and measurement equipment, security systems, and computer peripherals. In a point-of-sale terminal, the three transmitters can drive status indicators or service interfaces while the five receivers monitor keypad, sensor, and handshake signals. In an industrial controller, the device can bridge low-voltage logic and long RS-232 connections while its ESD protection reduces vulnerability to cable-borne transients. Design the circuit with the voltage ratings and external-charge-pump requirements specified in the manufacturer datasheet. Place bypass capacitors close to the supply and charge-pump nodes, route protected RS-232 lines away from sensitive clocks and data traces, and confirm that the connector and cable interface provide the intended ESD and common-mode protection. Verify signal polarity and handshake behavior in software because automatic shutdown and wakeup can affect receiver state at startup. This product page combines the manufacturer’s device specifications with practical RS-232 design guidance, compatible same-family alternatives, and a parameter-by-parameter comparison. It is intended to accelerate component selection while keeping the final engineering decision grounded in the official MAX3243E datasheet.

RFC Hubungi kami
MAX3243EETJ+T - 3/5 RS-232 Transceiver, 250kbps | Analog Devices
MAX3243EETJ+T

MAX3243EETJ+T - 3/5 RS-232 Transceiver, 250kbps | Analog Devices

The Analog Devices MAX3243EETJ+T is a 3.0V to 5.5V powered RS-232 interface transceiver with three transmit channels and five receive channels, supporting data rates up to 250kbps. It is packaged in a 32-pin TQFN with a 7 mm by 7 mm body and an exposed thermal pad for improved heat dissipation. The device includes automatic shutdown and wakeup functions, making it suitable for systems where the interface must remain available without continuously consuming power. An RS-232 transceiver is a signal-interface integrated circuit that converts between single-ended, bipolar RS-232 logic levels and CMOS/TTL logic levels used by microcontrollers, computers, and industrial controllers. The MAX3243E family belongs to the interface IC hierarchy: RS-232 transceiver, communications interface, and interface integrated circuit. It provides level translation, noise immunity, and electrical protection in one compact package. The MAX3243EETJ+T is specified for a 3.0V to 5.5V supply range, 15kV ESD protection on the RS-232 lines, and operation at rates up to 250kbps. Its three transmitters support point-to-point serial links, while its five receivers can monitor multiple incoming signals. Automatic shutdown reduces supply current when no active transmission is present, and the wakeup circuitry allows the interface to react to incoming serial activity. Typical uses include industrial control equipment, data acquisition systems, test and measurement instruments, service interfaces, and embedded products that communicate through legacy RS-232 ports. The exposed pad improves heat flow from the package to the PCB, but a proper thermal via and copper-pour layout remain necessary for reliable operation in elevated-temperature environments. When designing a board around this transceiver, route each RS-232 connector pin directly to the corresponding protection-capable interface pin and keep the ground return path close to the signal traces. Decoupling capacitors should be placed at the supply pins, and the exposed pad should be connected to the ground plane using multiple thermal vias. Review the manufacturer datasheet for the complete pin-description table and application circuit before assigning PCB tracks. This page combines manufacturer specifications, distributor package information, replacement analysis, and practical PCB guidance to help engineers evaluate the MAX3243EETJ+T for new RS-232 designs and for retrofit work where the original interface device is no longer readily available.

RFC Hubungi kami
MAX3243EEUI+ - 3/5 RS-232 Transceiver | Analog Devices
MAX3243EEUI+

MAX3243EEUI+ - 3/5 RS-232 Transceiver | Analog Devices

The Analog Devices MAX3243EEUI+ is a 3.0 V to 5.5 V RS-232 transceiver with three drivers, five receivers, 250 kbps data rate, ±15 kV ESD protection, and automatic shutdown/wakeup in a 28-pin TSSOP package. An RS-232 transceiver is an interface IC that converts logic-level digital signals into RS-232 line levels and converts incoming RS-232 signals back into CMOS-compatible logic. The MAX3243E belongs to the EIA/TIA-232 communications-interface family supporting V.28 and V.24 signaling. Its three-driver, five-receiver arrangement is particularly useful for DE-9 data-terminal-equipment connections, industrial control links, configuration ports, and service interfaces. Key features include operation from a 3.0 V to 5.5 V supply, a maximum data rate of 250 kbps, ±15 kV human-body-model ESD protection on serial-port pins, and low-power shutdown with automatic wakeup. The shutdown current is specified at 1 µA, while the always-enabled ROUT2B and INVALID outputs provide remote-ring and input-validity monitoring functions. The MAX3243E architecture supports both 3 V-powered and 5 V-powered systems. Automatic shutdown reduces supply consumption when the associated serial port is inactive, and automatic wakeup allows the interface to resume operation when valid serial activity is detected. This behavior is useful in distributed equipment where multiple RS-232 ports may remain present but unused for extended periods. Typical applications include industrial serial controllers, test and measurement instruments, point-of-sale terminals, security equipment, embedded service consoles, and legacy computer peripherals. The five receivers also provide extra input channels beyond the three transmit channels, enabling ring-indicator, remote-control, or status-signal monitoring alongside the primary serial connection. PCB design should preserve the manufacturer-recommended driver and receiver pin assignments, place the charge-pump and interface capacitors at their specified pins, and route exposed connector pins with direct ESD-current paths to ground. Check signal polarity, connector pin assignment, and logic levels before replacing an RS-232 controller with this transceiver. This page provides a focused selection guide, practical interface-layout notes, and a parameter comparison covering the MAX3243EEUI+ and its identified same-package option. Engineers can use the manufacturer datasheet and product page to confirm final pin routing, timing limits, and operating conditions before releasing a PCB.

RFC Hubungi kami
MAX3243EIDW - 3/5 RS-232 Transceiver | Texas Instruments
MAX3243EIDW

MAX3243EIDW - 3/5 RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3243EIDW is a 3/5 multichannel RS-232 line driver and receiver operating from a 3 V to 5.5 V supply, with data rates up to 500 kbps. It is housed in a 28-pin SOIC package and provides enhanced electrostatic-discharge protection of ±15 kV for IEC air-gap discharge and ±8 kV for contact discharge on serial-port connection pins. The device is intended for industrial, instrumentation, data-acquisition, and equipment-control interfaces requiring RS-232 compatibility with improved transient immunity. An RS-232 transceiver combines line drivers and line receivers in one interface circuit. The driver converts logic-level inputs into RS-232 bipolar levels, while the receiver converts differential, bipolar serial signals back into logic-compatible outputs. This MAX3243E device is positioned as a 3/5 transceiver for multichannel designs, allowing several RS-232 ports to share one package while reducing the number of external interface components. Key characteristics include a 500 kbps maximum signaling rate, operation across a 3 V to 5.5 V supply range, and industrial-temperature identification in the MAX3243EIDW ordering code. The E suffix denotes the enhanced ESD-protection family, making the device preferable to standard MAX3243 variants when exposed cables, connector contacts, or industrial wiring can introduce electrostatic discharge transients. The 28-pin SOIC footprint supports conventional through-hole or surface-mount assembly and is convenient for designs migrating from discrete RS-232 driver and receiver pairs. The MAX3243E is designed to meet the electrical requirements of the RS-232 standard while offering low-power operation from a single supply. The wide supply range permits use in systems with 3.3 V or 5 V logic rails, provided the interface is configured for the selected operating voltage. The transceiver architecture also allows designers to place receive and transmit functions close to a connector, reducing susceptibility to noise on long interconnects. Typical applications include industrial control consoles, serial test equipment, barcode and scanning systems, laboratory instrumentation, data-logging equipment, and RS-232 ports in embedded systems. The device is particularly useful where a cable-mounted connector can be exposed to electrostatic discharge during maintenance, plugging, or operation in electrically noisy environments. When laying out a board using the MAX3243EIDW, route each RS-232 driver and receiver connection directly to its connector and keep sensitive logic traces away from those protected connector pins. Confirm supply decoupling, grounding, and connector-return continuity in the manufacturer datasheet reference circuit. For systems requiring a different channel count or package, use the pin-configuration table and ordering information from the MAX3243E datasheet before selecting a substitute.

RFC Hubungi kami
MAX3243EIDWR - 3/5 RS-232 Transceiver, 500kbps | Texas Instruments
MAX3243EIDWR

MAX3243EIDWR - 3/5 RS-232 Transceiver, 500kbps | Texas Instruments

The Texas Instruments MAX3243EIDWR is a 3/5-channel RS-232 transceiver with three line drivers, five line receivers, and integrated charge-pump circuitry. It operates from a 3 V to 5.5 V supply, supports data rates up to 500 kbps, and is specified for industrial temperatures from -40 °C to +85 °C. The device is packaged in a 28-pin SOIC (DW) package. An RS-232 transceiver is the interface class that converts between digital logic levels and the differential voltage levels used by RS-232 serial links. The MAX3243EIDWR combines transmit and receive functions in one package, allowing a compact asynchronous serial-port interface. Its integrated dual charge pump generates the positive and negative voltage levels required by RS-232 drivers without requiring external negative-supply components. The principal protection feature is ±15 kV IEC ESD protection on the serial-port connection pins. The manufacturer specifies protection for HBM and IEC 61000-4-2 air-gap discharge, with ±8 kV contact-discharge protection. This makes the interface suitable for equipment exposed to electrostatic discharge at connector entry points. The device is designed to meet TIA/EIA-232-F requirements. The MAX3243EIDWR is appropriate for industrial control equipment, data acquisition systems, service interfaces, and embedded serial-port designs. Its 500 kbps capability supports communication with legacy peripherals and higher-speed control equipment while the 3 V to 5.5 V supply range allows use in both 3.3 V and 5 V systems. The three drivers and five receivers provide flexibility for multi-channel serial links. Designers should follow the manufacturer pin-description table and typical application circuit when assigning connector signals. Place charge-pump capacitors and supply bypass capacitors close to their specified pins, keep the protected serial traces away from sensitive analog circuitry, and provide adequate ESD-return paths through the connector and chassis. The 28-pin SOIC footprint allows straightforward use in conventional surface-mount PCB layouts. This page consolidates the manufacturer specifications, package information, interface guidance, and practical replacement considerations for engineers evaluating the MAX3243EIDWR in a 3 V to 5.5 V RS-232 design.

RFC Hubungi kami
MAX3243EIPW - 500kbps 3/5 RS-232 Transceiver | Texas Instruments
MAX3243EIPW

MAX3243EIPW - 500kbps 3/5 RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3243EIPW is a 3-to-5.5 V multichannel RS-232 line driver and receiver supporting a maximum data rate of 500 kbps. It integrates three drivers and five receivers in a 28-pin TSSOP (PW) package, and its transceiver outputs provide plus or minus 15 kV IEC electrostatic-discharge protection. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received line-level signals back into CMOS-compatible logic. In the broader electronics hierarchy, the MAX3243EIPW belongs to the interface-controller family, supports the EIA/TIA-232 communications standard, and provides the physical-layer signaling required between computers, industrial controllers, instrumentation, and other serial equipment. The device combines three driver channels and five receiver channels in one package. Its 3-to-5.5 V supply range allows operation from both 3.3 V and 5 V systems, while the 500 kbps maximum data rate supports moderate-speed point-to-point serial links. Automatic shutdown and wake-up functions can reduce supply demand when the associated receiver is inactive, and plus or minus 15 kV IEC ESD protection improves robustness on cables exposed to electrostatic discharge. The MAX3243EIPW is a pin-compatible member of the MAX3243E interface family, and the TRS3243E designation provides a second-source ordering path for the same device. Its 28-pin TSSOP package is substantially smaller than the older 28-pin DIP representation and supports compact PCB construction. The industrial temperature grade covers minus 40°C to plus 85°C operation, making the device suitable for factory equipment, data acquisition systems, service interfaces, and embedded serial ports. Typical applications include industrial control consoles, laboratory test equipment, point-of-sale terminals, security systems, external data-loggers, and embedded UART links. The three transmitters allow multiple outputs, while the five receivers support several incoming serial ports or multiple receive-connected inputs. The 500 kbps rate is appropriate for configuration transfers, status polling, command exchange, and short-distance industrial communication rather than continuous high-volume file transfers. For layout, keep the IC close to the protected connector and route each RS-232 trace as a short, direct channel. Follow the manufacturer datasheet for charge-pump capacitors, driver output connections, receiver inputs, and the exact supply-bypass arrangement. Confirm signal polarity and receiver input states before enabling a channel, especially when replacing a legacy MAX3243 implementation. This page combines the manufacturer specifications with practical transceiver application guidance, channel-count comparisons, package compatibility analysis, and design notes. These resources help engineers evaluate the MAX3243EIPW for both new RS-232 designs and existing 28-pin TSSOP board revisions.

RFC Hubungi kami
MAX3243EIPWG4 - RS-232 Transceiver | Texas Instruments
MAX3243EIPWG4

MAX3243EIPWG4 - RS-232 Transceiver | Texas Instruments

Texas Instruments MAX3243EIPWG4 is a four-channel RS-232 line driver and receiver with 3 V to 5.5 V supply operation, 250 kbps data signaling, and ±15 kV IEC ESD protection. The device is packaged in a 28-pin TSSOP and operates from -40°C to +85°C. An RS-232 transceiver is an interface IC that combines a line driver, which converts logic-level signals into RS-232 voltage levels, with a receiver, which converts incoming RS-232 signals back into logic-compatible levels. It belongs to the communication-interface hierarchy: transceiver → RS-232 interface IC → interface IC → integrated circuit. This integration reduces the component count and board area required for multiport serial connections. The MAX3243EIPWG4 provides four driver and four receiver channels, allowing two complete bidirectional RS-232 ports to be implemented with one package. Its 3 V to 5.5 V operating range supports both 3.3 V and 5 V system rails. The 250 kbps maximum data rate is suitable for legacy serial ports, industrial equipment, data-acquisition systems, and embedded control links. The MAX3243E designation adds enhanced electrostatic-discharge protection to the serial connections. The manufacturer describes ±15 kV IEC ESD protection, while component data also identifies ±15 kV HBM and air-gap discharge protection and ±8 kV IEC61000-4-2 contact-discharge protection. These ratings strengthen the external serial interface against electrostatic events encountered during connection, servicing, and industrial operation. Typical uses include industrial serial controllers, test and measurement equipment, point-of-sale terminals, security equipment, and embedded systems that retain an RS-232 port. The device is also useful when legacy peripherals must coexist with modern low-voltage logic because its receive and transmit functions operate from the same 3 V to 5.5 V supply range. Designers should preserve the recommended charge-pump capacitor and interface-decoupling networks, route protected connector pins directly to the device, and maintain an unobstructed return path for RS-232 signals. Because the exact MPN is listed as obsolete, new production designs should first confirm lifecycle requirements and compare the current MAX3243 family ordering options. This product page combines the manufacturer specifications, interface-protection ratings, package information, lifecycle status, and verified replacement context into a design-focused reference. It also highlights where a same-package substitute may require review of ESD ratings, temperature coverage, or ordering qualification.

RFC Hubungi kami
MAX3243EIPWR - 500kbps 3/5 RS-232 Transceiver | Texas Instruments (Tape & Reel)
MAX3243EIPWR

MAX3243EIPWR - 500kbps 3/5 RS-232 Transceiver | Texas Instruments (Tape & Reel)

The Texas Instruments MAX3243EIPWR is a 3-to-5.5 V multichannel RS-232 line driver and receiver supporting a maximum data rate of 500 kbps. It integrates three drivers and five receivers in a 28-pin TSSOP (PW) package, and its transceiver outputs provide plus or minus 15 kV IEC electrostatic-discharge protection. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received line-level signals back into CMOS-compatible logic. In the broader electronics hierarchy, the MAX3243EIPWR belongs to the interface-controller family, supports the EIA/TIA-232 communications standard, and provides the physical-layer signaling required between computers, industrial controllers, instrumentation, and other serial equipment. The device combines three driver channels and five receiver channels in one package. Its 3-to-5.5 V supply range allows operation from both 3.3 V and 5 V systems, while the 500 kbps maximum data rate supports moderate-speed point-to-point serial links. Automatic shutdown and wake-up functions can reduce supply demand when the associated receiver is inactive, and plus or minus 15 kV IEC ESD protection improves robustness on cables exposed to electrostatic discharge. The MAX3243EIPWR is a pin-compatible member of the MAX3243E interface family, and the TRS3243E designation provides a second-source ordering path for the same device. Its 28-pin TSSOP package is substantially smaller than the older 28-pin DIP representation and supports compact PCB construction. The industrial temperature grade covers minus 40°C to plus 85°C operation, making the device suitable for factory equipment, data acquisition systems, service interfaces, and embedded serial ports. Typical applications include industrial control consoles, laboratory test equipment, point-of-sale terminals, security systems, external data-loggers, and embedded UART links. The three transmitters allow multiple outputs, while the five receivers support several incoming serial ports or multiple receive-connected inputs. The 500 kbps rate is appropriate for configuration transfers, status polling, command exchange, and short-distance industrial communication rather than continuous high-volume file transfers. For layout, keep the IC close to the protected connector and route each RS-232 trace as a short, direct channel. Follow the manufacturer datasheet for charge-pump capacitors, driver output connections, receiver inputs, and the exact supply-bypass arrangement. Confirm signal polarity and receiver input states before enabling a channel, especially when replacing a legacy MAX3243 implementation. This page combines the manufacturer specifications with practical transceiver application guidance, channel-count comparisons, package compatibility analysis, and design notes. These resources help engineers evaluate the MAX3243EIPWR for both new RS-232 designs and existing 28-pin TSSOP board revisions.

RFC Hubungi kami
MAX3243EIPWRE4 - 500kbps RS-232 Transceiver | Texas Instruments
MAX3243EIPWRE4

MAX3243EIPWRE4 - 500kbps RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3243EIPWRE4 is a 3 V to 5.5 V multichannel RS-232 line driver and receiver with 500 kbps signaling and plus-or-minus 15 kV IEC ESD protection, housed in a 28-pin TSSOP package. The device is designed for systems that require multiple serial data channels and reliable protection for exposed RS-232 connections. An RS-232 transceiver combines a line driver, which converts logic-level signals into RS-232 voltage levels, with a receiver, which converts incoming RS-232 signals back into logic-level voltages. The MAX3243EIPWRE4 provides three transmitters and five receivers, allowing five inbound channels and three outbound channels in one interface circuit. This integration reduces the number of separate interface ICs required in multi-channel equipment. The MAX3243E family operates from a 3 V to 5.5 V supply, supporting both 3.3 V and 5 V system rails. Its maximum data rate is 500 kbps, making it appropriate for instrumentation, industrial control, data acquisition, point-of-sale equipment, and other serial interfaces operating well below that limit. The E designation corresponds to the enhanced ESD-protection version identified by the manufacturer. The integrated protection is specified as plus-or-minus 15 kV IEC ESD protection. This feature is important when a board connects through an external connector or long cable because electrostatic discharge can otherwise damage the interface IC. Protection capability does not eliminate the need for sound board layout, controlled ground return paths, chassis grounding, and appropriate surge protection in severe environments. The MAX3243EIPWRE4 is specified from minus 40 degrees Celsius to 85 degrees Celsius, covering industrial-temperature commercial equipment. Its 28-TSSOP package is suitable for compact, surface-mounted PCB layouts, but engineers should preserve adequate clearance around the package and route interface signals away from sensitive analog and clock paths. When designing around this transceiver, verify that the host UART, cable connector, logic levels, and line termination match the intended RS-232 application. Software should also handle RS-232 control signals and the behavioral differences between DTE and DCE equipment. The manufacturer product page and datasheet are the authoritative references for electrical limits, pin assignments, truth tables, and recommended application circuits.

RFC Hubungi kami
MAX3243EIRHBR - 500kbps RS-232 Transceiver | Texas Instruments
MAX3243EIRHBR

MAX3243EIRHBR - 500kbps RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3243EIRHBR is a multichannel RS-232 line driver and receiver operating from 3V to 5.5V at up to 500kbps, packaged in a 32-VQFN 5x5mm package. It integrates three line drivers, five line receivers, and a dual charge-pump circuit for RS-232 signal-level conversion. An RS-232 transceiver is an interface IC that translates logic-level signals from a host, controller, or embedded processor into RS-232-compatible levels and converts returning RS-232 signals back into logic levels. It belongs to the interface IC hierarchy, where transceiver products connect digital systems to communication ports requiring greater signal range, noise immunity, and electrical protection than ordinary logic I/O provides. The MAX3243EIRHBR provides three transmit channels and five receive channels, allowing several RS-232 links to be consolidated in one device. Its dual charge-pump circuit supports single-supply operation, while the integrated charge-pump capacitors reduce external component count. The device is designed for asynchronous serial communication and meets TIA/EIA-232-F interface requirements. ESD protection is a defining feature of the MAX3243E family. According to the manufacturer product documentation, the serial-port connection pins withstand plus or minus 15kV using the HBM and IEC61000-4-2 air-gap discharge methods, plus or minus 8kV using the IEC61000-4-2 contact-discharge method. These ratings help protect connector-facing circuitry from electrostatic discharge events. Typical applications include industrial serial-port adapters, test and measurement equipment, point-of-sale terminals, data-acquisition modules, and embedded systems that connect legacy RS-232 peripherals. The combination of multiple drivers, multiple receivers, a 3V to 5.5V supply range, and protected connector pins supports compact multi-port designs where board area and component count are important. PCB layout should keep the charge-pump capacitor connections and connector-side signal paths compact and appropriately separated. Pay particular attention to exposed-pad soldering, grounding, and the relationship between external cable transients and the protected RS-232 pins. Verify the complete pin configuration in the manufacturer pin-description table before assigning signals because the orderable RHB package includes power, ground, driver, receiver, and exposed-pad connections. This page combines the manufacturer's electrical and protection ratings with package information, same-footprint alternatives, application guidance, and design-oriented comparisons. These engineering details help distinguish the MAX3243EIRHBR from lower-channel-count transceivers, alternative data-rate versions, and other 32-pin RS-232 interface families.

RFC Hubungi kami
MAX3243EIRHBRG4 - 500kbps RS-232 Transceiver | Texas Instruments
MAX3243EIRHBRG4

MAX3243EIRHBRG4 - 500kbps RS-232 Transceiver | Texas Instruments

Texas Instruments MAX3243EIRHBRG4 is a 3 V to 5.5 V multichannel RS-232 line driver/receiver featuring three drivers, five receivers, a dual charge-pump circuit, and a 500kbps data rate. The device is packaged in a 32-pin VQFN (HVQCCN) package measuring 5 mm by 5 mm and is specified for an industrial temperature range of -40 °C to 85 °C. An RS-232 transceiver is an interface integrated circuit that converts logic-level signals into RS-232 line levels and converts received RS-232 signals back into logic levels. Within the interface hierarchy, the MAX3243E combines a line driver, line receiver, and charge-pump voltage converter to support the bipolar voltage swings required by TIA/EIA-232-F on systems powered from a single 3 V to 5.5 V supply. The MAX3243E family includes 3-to-5.5 V operation, a 500kbps maximum data rate, and enhanced electrostatic-discharge protection. According to the manufacturer product information, serial-port pins provide plus-or-minus 15kV HBM and IEC61000-4-2 air-gap discharge protection, plus plus-or-minus 8kV IEC61000-4-2 contact-discharge protection. These ratings are important when the interface connects to externally accessible equipment through an unprotected cable. Internally, the dual charge-pump circuit generates the positive and negative voltages used by the line drivers, allowing the device to operate from a single low-voltage supply without an external negative supply. Three line drivers and five line receivers support common RS-232 serial-port arrangements where more receive channels are useful for handshake, status, or control signals. The receiver architecture is intended for asynchronous communication-controller interfaces operating at rates up to 500kbps. Typical applications include industrial serial links, data-acquisition equipment, barcode and point-of-sale systems, test instrumentation, and embedded control systems. It is also suitable for equipment implementing RS-232 over cable runs where surge and electrostatic-discharge exposure is likely. System designers should still retain appropriate board-level grounding, cable routing, and chassis-protection practices because the IC ratings address specified ESD test conditions rather than every possible surge event. The primary design consideration is decoupling. Place the charge-pump capacitors and supply capacitors close to their designated pins, keep the exposed-pad thermal and electrical connection correctly implemented, and follow the manufacturer layout guidance. Confirm that the selected connector, cable, and system grounding strategy produce compatible RS-232 levels before releasing a production design. This page combines manufacturer specifications, package details, replacement guidance, comparison data, and practical implementation notes for faster engineering evaluation.

RFC Hubungi kami
MAX3243EUI+ - 3.3V/5V RS-232 Transceiver | Analog Devices
MAX3243EUI+

MAX3243EUI+ - 3.3V/5V RS-232 Transceiver | Analog Devices

Analog Devices MAX3243EUI+ is a +3V to +5.5V RS-232 transceiver with three drivers and three receivers, automatic shutdown and wake-up, full-duplex operation, and enhanced electrostatic-discharge protection in a 28-pin TSSOP package. According to the manufacturer product page, the MAX3243 family is in production and supports both 3V and 5V supply operation. An RS-232 transceiver is a serial-interface integrated circuit that converts between TTL/CMOS logic levels and the voltage-defined RS-232 signal levels used by computer serial ports and industrial equipment. The MAX3243EUI+ belongs to the interface-IC hierarchy: RS-232 transceiver → multi-channel serial-interface transceiver → communications interface IC → semiconductor. Automatic shutdown provides a practical power-management advantage when no valid receiver activity is detected. Key features include a 3V to 5.5V supply range, three transmit channels, three receive channels, AutoShutdown operation, enhanced ESD protection, and a 28-pin TSSOP package. The MAX3243E family description identifies EIA/TIA-232 and V.28/V.24 support, automatic shutdown and wake-up behavior, high data-rate capability, and enhanced electrostatic-discharge protection. These characteristics suit systems that must translate between modern digital logic and legacy RS-232 ports. The MAX3243EUI+ integrates both interface directions on one device, reducing the component count required for a multi-channel serial port. Its automatic shutdown function can reduce power consumption when the remote system is disconnected or inactive. The 28-pin TSSOP is a surface-mount package that supports conventional PCB assembly, although exact pin assignments, capacitor values, and electrical limits must be confirmed from the manufacturer datasheet before layout or replacement qualification. Typical uses include industrial control equipment, data-acquisition systems, configuration ports, service interfaces, and embedded systems that need to communicate with RS-232 peripherals. It is also appropriate for battery-powered or portable equipment where automatic shutdown can conserve energy during idle periods. In those applications, logic-level compatibility, ESD protection, and cable-receiver behavior are as important as the nominal data rate. When designing around the MAX3243EUI+, verify the complete supply range, operating temperature, absolute maximum ratings, driver slew rate, receiver thresholds, and required external charge-pump capacitors against the manufacturer datasheet. Place the interface IC close to the connector, route driver outputs toward the protected connector side, and provide a low-impedance ground return so common-mode noise does not corrupt receiver inputs. This page consolidates verified manufacturer and distributor information with practical selection guidance, parameter comparisons, and engineering-oriented interface design notes. It also distinguishes verified drop-in candidates from unresolved alternatives, helping engineers reduce sourcing risk while retaining the required 28-pin TSSOP footprint.

RFC Hubungi kami