Produk (44,000+)

MC14053BD - Triple 2:1 Analog Multiplexer | onsemi
MC14053BD

MC14053BD - Triple 2:1 Analog Multiplexer | onsemi

onsemi MC14053BD is a triple 2:1 analog multiplexer and demultiplexer IC designed to route analog signals among multiple channels using digital control inputs. The device is identified as a 3-circuit IC switch with 280 ohm on-state resistance in a 16-SOIC package. According to the manufacturer product information, its supported analog signal range is 3.0 V to 18 V when VEE is no higher than VSS, making it suitable for conventional CMOS control and low-voltage analog signal routing systems. An analog multiplexer is a semiconductor switching device that connects one of several signal terminals to a common terminal. The MC14053B family provides three independent 2:1 selections, allowing multiple analog sources to be routed through one shared signal path. Digital select inputs determine which source or destination is connected, while the analog switches provide bidirectional signal paths suitable for multiplexed and demultiplexed operation. Key features include three independently controlled 2:1 analog switches, 280 ohm on-state resistance, operation over a 3.0 V to 18 V analog voltage range, and a 16-SOIC package. The manufacturer also identifies low-noise performance of 12 nV per square-root-hertz for frequencies up to 1.0 kHz. These characteristics make the device useful for sensor selection, measurement routing, signal conditioning, test systems, and other applications requiring controlled analog-channel access. The MC14053B is part of the CMOS logic family of analog switches. Its digital control architecture allows a microcontroller or logic controller to select among signal paths without changing the physical routing of the analog network. Because the device is bidirectional, the same switching network can support multiplexing, demultiplexing, signal swapping, and routing functions depending on the external circuit configuration. Typical applications include multiplexed sensor interfaces, instrumentation signal routing, data acquisition systems, communication equipment, and industrial control modules. In a sensor interface, the select lines can choose among several inputs before amplification or conversion. In a data acquisition circuit, separate control logic can direct different sources to a shared analog front end while minimizing the number of separate signal-chain channels. Designers should confirm the actual pinout, control truth table, supply limits, and input voltage limits in the manufacturer datasheet before layout. The unused selector and signal terminals should be handled according to the datasheet guidance, and the common analog path should be kept away from switching nodes and high-current return paths to reduce coupling and crosstalk. This page consolidates the manufacturer product information, package identification, channel configuration, on-state resistance, supported voltage range, and low-noise figure into a practical reference for engineers selecting an analog multiplexer. It also distinguishes device-level switching facts from parameters that must be confirmed directly from the datasheet.

RFC Hubungi kami
MC14053BF - Triple SPDT Analog Multiplexer | onsemi
MC14053BF

MC14053BF - Triple SPDT Analog Multiplexer | onsemi

The onsemi MC14053BF is a triple single-pole double-throw CMOS analog multiplexer with an operating supply range of 3 V to 18 V, an on-state resistance of 280 ohms, and a 16-SOEIAJ package. The device routes three independent analog signals through common digital address and inhibit-control inputs, making it suitable for instrumentation, data acquisition, communication, and test systems. An analog multiplexer is an interface IC that connects multiple signal sources to a shared processing channel. The MC14053BF belongs to the broader multiplexer and demultiplexer hierarchy, which sits within analog switches, interface ICs, and semiconductor signal-routing components. Unlike a mechanical selector, its CMOS switching elements are controlled by logic levels, allowing compact and repeatable signal selection. Key features include three 2:1 switching paths, a 3 V to 18 V analog operating range, and a typical on-state resistance of 280 ohms. The onsemi product information also identifies a pin-for-pin replacement relationship with the CD4053 function and a typical low-noise figure of 12 nV per square root hertz at frequencies up to 1 kHz. Lead-free packages are offered, making package selection important for environmentally conscious production programs. Internally, the MC14053BF uses complementary analog switches to select between paired inputs for each channel. Address logic determines the active throw, while the inhibit input provides a common control path for disabling the selected channels. Designers must maintain valid logic levels across the full supply range and account for off-state leakage, switching transients, charge injection, and the finite 280-ohm path resistance when setting source and measurement impedances. Typical applications include multiplexed sensor acquisition, audio routing, industrial control interfaces, communication equipment, and laboratory test systems. It is particularly useful when several low-frequency or moderate-bandwidth analog signals must share one amplifier, converter, or measurement channel. Its 280-ohm resistance can create source-loading error when driving a high-impedance amplifier or a comparatively low-impedance ADC input. A key design practice is to place the multiplexer close to the signal source, use high-impedance buffering where necessary, and validate the complete acquisition path for settling time and crosstalk. The data-select and inhibit traces should remain short and away from noisy clock or power-conversion nodes. Supply bypassing and return-current planning are also important because rapidly switching analog paths can inject transients into sensitive measurement circuitry. This product record combines manufacturer feature data with practical guidance for multiplexing, signal integrity, PCB implementation, and replacement selection. It also distinguishes true pin-compatible options from functional alternatives so engineers can reuse an existing 16-pin layout without overlooking control-logic, package, or signal-integrity differences.

RFC Hubungi kami
MC14060BF - 14-Bit Counter with Oscillator | onsemi
MC14060BF

MC14060BF - 14-Bit Counter with Oscillator | onsemi

onsemi MC14060BF is a 14-stage binary ripple counter with an on-chip oscillator buffer, supplied in a 16-pin SOIC package. It provides 14 binary counter outputs, a common reset function that clears all outputs and disables the oscillator, and an oscillator arrangement that supports RC or crystal timing networks. The clock advances the counter on a negative transition, making the device suitable for frequency division, timing generation, pulse counting, and periodic control functions. A binary ripple counter is a digital sequential circuit in which each counting stage drives the next stage. The MC14060BF belongs to the counter and divider hierarchy within CMOS logic ICs. Its integrated oscillator removes the need for a separate clock generator when a free-running time base is required. If an external clock is available, the clock input allows the circuit to operate as a divide-by-2 through divide-by-16,384 counter chain. The on-chip oscillator buffer supports both resistor-capacitor and crystal oscillator configurations. The onsemi datasheet also identifies a Schmitt-trigger clock input, which improves switching behavior when the clock waveform has a slow edge or appreciable noise. Buffered outputs are available from stages 4 through 10 and stages 12 through 14, providing usable drive capability for selected divider outputs in frequency-divider and timing applications. A common reset input places every counter output into the zero state and disables the oscillator. This behavior allows a system controller to establish a known timing origin, synchronize multiple events, or restart a periodic sequence. Each negative transition on the clock advances the count by one, and the 14 counter stages provide a total division ratio of 16,384 when the highest-order output is used. Typical applications include digital clocks and timers, industrial sequence controllers, periodic pulse generators, frequency dividers, phase-shift systems, and embedded control systems requiring a local time base. The 16-pin SOIC package also allows the counter to be used on conventional surface-mount control boards where a larger leaded package would be unnecessary. For reliable oscillator operation, keep the oscillator and clock traces short and place timing components close to the device. When using an RC network, validate component tolerance and temperature behavior across the intended operating range. For crystal timing, follow the manufacturer connection and load recommendations and maintain clean return paths to reduce false clock transitions. This product page combines the MC14060B functional description, package information, drop-in alternatives, comparison parameters, and practical oscillator and layout guidance to support faster component selection and implementation.

RFC Hubungi kami
MC14066BD - 3-18V Quad Analog Switch | onsemi | SOIC-14
MC14066BD

MC14066BD - 3-18V Quad Analog Switch | onsemi | SOIC-14

The onsemi MC14066BD is a 3-18 V quad analog switch and quad multiplexer integrated circuit packaged in a 14-pin SOIC. It contains four independent bilateral switches, allowing each switch to control either a digital or an analog signal. The MC14066B family is designed for signal gating, chopper, modulator, demodulator, and CMOS logic applications, while individual control inputs can switch signal excursions as large as the full supply voltage. An analog switch is a semiconductor device that routes a signal between circuit nodes under digital control. The MC14066BD belongs to the analog switch and multiplexer hierarchy, which sits within interface ICs and broader logic semiconductor systems. Unlike a mechanical relay, its switching action is controlled by CMOS-compatible logic and is intended for compact signal-routing implementations. Its four independent switches allow one package to handle multiple gated channels without requiring four separate single-switch packages. The key defining feature is the MC14066B family's pin-for-pin compatibility with the onsemi MC14016B. The manufacturer states that the MC14066B provides substantially lower ON resistance than the MC14016B while retaining compatibility between the two devices. Its 3-18 V operating range supports both lower-voltage CMOS logic systems and higher-voltage analog signal-routing systems. Each of the four switches has a separate control input, allowing independent routing decisions within one circuit. The MC14066BD uses parallel MOSFET-style switch elements to provide bilateral signal paths. A control signal determines whether the corresponding path is ON or OFF, and the switched signal can travel in either direction. This bilateral behavior makes the device suitable for signal gating, multiplexed test paths, chopper functions, modulation and demodulation stages, and general CMOS logic implementations where multiple analog or logic nodes must be routed independently. Typical uses include switching sensor outputs in industrial measurement systems, routing audio-range signals in test equipment, selecting external networks in control circuits, and implementing modulator or demodulator functions. Because the control inputs operate from the same supply family as the signal paths, system designers should account for input logic levels, permissible signal excursions, ON-resistance effects, and off-state leakage when choosing external bias and interface components. For PCB implementation, place the device so that switched signal traces remain short and away from high-current switching nodes. Use a common ground reference and provide a clean supply connection where logic thresholds matter. Confirm the exact pin assignment, electrical limits, and recommended operating conditions in the onsemi MC14066B datasheet before finalizing signal amplitude, control timing, and external resistor values. This page consolidates the manufacturer’s core switch characteristics, package information, pin-compatibility guidance, application contexts, and design considerations into an engineering-focused selection reference. It also distinguishes the verified MC14016B relationship from unsupported substitutions, helping designers identify where a board-level change can be evaluated without relying on a generic cross-reference listing.

RFC Hubungi kami
MC14071BDR2G - Quad 2-Input OR Gate, 3-18V CMOS, SOIC-14 | onsemi
MC14071BDR2G

MC14071BDR2G - Quad 2-Input OR Gate, 3-18V CMOS, SOIC-14 | onsemi

The onsemi MC14071BDR2G is a B-suffix series Quad 2-Input OR Gate built with P-channel and N-channel enhancement-mode CMOS transistors in a single monolithic structure, supplied in a 14-pin SOIC package. It contains four independent 2-input OR gates and operates across a wide supply voltage range of 3 V to 18 V DC, with logic-level compatibility across the full range. An OR gate is a fundamental combinational logic device that outputs a logic HIGH whenever at least one of its inputs is HIGH; four such gates share a common power rail in the MC14071B, forming part of the 4000-series CMOS logic family. This family sits within the broader hierarchy: logic gate -> combinational logic -> digital IC -> integrated circuit -> semiconductor. The MC14071BDR2G is widely used as a glue-logic building block in mixed-signal systems, replacing discrete transistors and providing reliable logic OR-ing where board-level routing is critical. Key features include extremely low quiescent supply current (typically 0.5 nA per gate at 5 V), high noise immunity of 45% of VDD minimum, and 5 V, 10 V, and 15 V parametric ratings per JEDEC JESD 20. Output drive is symmetric CMOS with balanced rise/fill characteristics and ESD protection on all inputs. The MC14071BDR2G's buffered-output architecture provides consistent fan-out and clean logic levels across the supply range, while inputs are diode-protected against over-voltage transients. The MC14071BDR2G uses a complementary MOS (CMOS) process in which P-channel pull-ups and N-channel pull-downs are co-integrated; this yields the family's hallmark near-zero quiescent current (current flows only during switching), making it ideal for battery-powered equipment. Designers can cascade gates for combinatorial logic, use the part as a logic-level translator between 5 V and 12 V domains, or wire OR multiple interrupt sources together for MCU monitoring. The 14-SOIC footprint is footprint-compatible with the rest of the MC140xx family, allowing easy migration to NAND, AND, NOR or XOR equivalents when board real-estate is reserved. Typical applications for the MC14071BDR2G include industrial control logic, automotive body electronics, battery-powered instrumentation, alarm-system OR-tying, and general-purpose glue logic in mixed-signal PCBs. The wide 3-18 V supply tolerates 12 V and 15 V analog rails, simplifying designs that interface to legacy analog sections. When designing with this part, observe standard CMOS handling precautions: tie all unused inputs to VDD or GND to prevent floating-input oscillation and extra current draw. The MC14071BDR2G is a direct functional replacement for the legacy CD4071B from Texas Instruments and is drop-in compatible on most 14-pin SOIC layouts.

RFC Hubungi kami
MC1430G - Low-Offset Amplifier, 33V/us | Motorola
MC1430G

MC1430G - Low-Offset Amplifier, 33V/us | Motorola

The Motorola MC1430G is a single-circuit general-purpose operational amplifier with a 10 mV input offset voltage, 33 V/us slew rate, 75 dB common-mode rejection, and low 15 uA input bias current. The verified component data identifies a -9 V to +9 V supply range, a 0 °C to +70 °C commercial operating range, and 9.2 mA supply current. Distributor listings classify the device as a metal-can instrumentation or general-purpose amplifier. An operational amplifier is a voltage-gain stage that compares its inverting and non-inverting inputs. The difference between those voltages is amplified by a very high open-loop gain and then conditioned to drive the intended external feedback network. In the broader semiconductor hierarchy, the MC1430G belongs to the operational-amplifier, analog-amplifier, linear-amplifier, and analog IC families. It is intended for applications requiring signal amplification rather than power conversion or logic operation. The principal verified performance parameters include a 10 mV input offset voltage, 15 uA input bias current, 400 nA input bias-current variation, 33 V/us slew rate, 75 dB common-mode rejection, and 9.2 mA supply current. The 10 mV offset establishes the practical dc error that must be considered in precision signal chains. The 33 V/us slew rate limits how quickly the output can follow a changing input, while 75 dB common-mode rejection reduces the output response to voltage applied simultaneously to both inputs. MC1430G operates from -9 V to +9 V and supports a 0 °C to +70 °C temperature range. These limits place it in the traditional bipolar, dual-supply general-purpose amplifier class. Its metal-can construction reflects an older package family used for through-hole and panel or chassis-style applications. The verified distributor descriptions consistently identify one amplifier circuit and a metal-can package, although the available listings express the package designation inconsistently. Typical uses include low-level instrumentation, feedback stages around transducers, analog signal conditioning, and general-purpose voltage amplification. In a practical circuit, the amplifier should be configured with suitable negative feedback, supply bypassing, and output loading appropriate for the required signal bandwidth. The MC1430G can be used where a 33 V/us slew rate and 75 dB common-mode rejection are sufficient, but its 10 mV offset may make it less attractive than a lower-offset precision amplifier in high-gain dc measurement systems. Designers should verify the exact physical lead numbering and package dimensions against the manufacturer datasheet before PCB layout or replacement work. The available verified data does not expose a complete pin map, and the distributor records refer to metal-can and TO-100-style descriptions inconsistently. Power-supply bypassing, input common-mode range, output swing, bias-current compensation, and stability with the selected feedback network also require confirmation before production release. This page consolidates the verified distributor specifications, sourcing information, package ambiguity, and selection guidance for the MC1430G. It also separates directly verified data from fields that still require manufacturer-datasheet confirmation, helping engineers avoid treating generic cross-reference pages as proof of pin-to-pin compatibility.

RFC Hubungi kami
MC1436CD - ±36V Internally Compensated Op Amp | Motorola
MC1436CD

MC1436CD - ±36V Internally Compensated Op Amp | Motorola

Motorola MC1436CD is a single-amplifier, general-purpose operational amplifier designed for high-voltage signal chains, with a specified supply range of ±36 V and internally compensated operation. The device is available in an 8-pin SOIC package, making the MC1436CD suitable for industrial, instrumentation, feedback-control, summing, and integration circuits where a conventional low-voltage operational amplifier cannot tolerate the required supply voltage. Its internally compensated architecture simplifies closed-loop design because the manufacturer identifies the MC1436 family as suitable for summing-amplifier, integrator, and external-feedback applications. The MC1436 belongs to the operational-amplifier hierarchy, where an operational amplifier is a differential-input voltage-amplifier IC used to amplify, buffer, sum, or integrate signals. An internally compensated operational amplifier integrates the frequency-compensation network, reducing the number of external components required for stable negative-feedback operation. The MC1436CD consequently sits between generic amplifier functions and precision signal-conditioning applications, while its ±36 V rating distinguishes it from common ±5 V, ±12 V, and ±15 V amplifier families. The verified product information identifies the MC1436 as a high-voltage, internally compensated operational amplifier intended for operation with external feedback components. This architecture supports conventional inverting and non-inverting amplifier configurations, active summing networks, and closed-loop integrators. Because the exact gain-bandwidth, slew-rate, input-offset, bias-current, input-common-mode-range, and output-swing limits are not included in the supplied source snippets, designers must consult the complete four-page MC1436CD datasheet before fixing loop gain, compensation, noise, accuracy, and stability margins. Typical industrial uses include process-control loops, high-voltage sensor interfaces, laboratory instrumentation, analog summing and averaging circuits, and active integrators. Its 8-pin SOIC format also supports compact surface-mount assemblies, although exposed-pad thermal analysis is not applicable because the specified package has no stated exposed thermal pad. Designers should still provide adequate copper and consider nearby heat sources because dissipation rises as supply voltage and output current increase. A key design consideration is to verify the complete DC and AC parameter set before replacing the amplifier with a lower-voltage modern part. The ±36 V supply capability is the principal differentiator, but stability, common-mode range, output swing, slew rate, and offset behavior determine whether a substitute is truly interchangeable. The available MC1436CD documentation is a four-page datasheet; no revision number or additional document number is established by the supplied data. This page consolidates verified distributor identification, package information, high-voltage operation, application positioning, cross-reference findings, and practical selection guidance. It also distinguishes documented facts from parameters that still require confirmation from the complete manufacturer datasheet, supporting faster sourcing without obscuring design-critical uncertainties.

RFC Hubungi kami
MC14407L - Full-Duplex 8-Bit PCM Codec | Motorola
MC14407L

MC14407L - Full-Duplex 8-Bit PCM Codec | Motorola

Motorola MC14407L is a full-duplex 8-bit companded PCM codec designed for telecommunications interface applications. The verified source information identifies A-law and mu-law companding support, a 24-pin CDIP package, and an operating temperature range of -40°C to +85°C. Its principal function is to convert between 8-bit companded PCM voice signals and the parallel digital interface used by a telecommunications system. A PCM codec is a semiconductor interface IC that performs the digital conversion required by pulse-code-modulation communication systems. In the hierarchy of electronic components, a codec belongs to the interface IC and telecom-interface categories, between general-purpose integrated circuits and complete voice-processing subsystems. Companded PCM reduces the number of bits required to represent selected voice-amplitude ranges while retaining a representation suitable for transmission over digital communication links. The MC14407L supports both A-law and mu-law operation, allowing it to match common digital telephony signaling conventions. Its full-duplex architecture supports simultaneous transmit and receive signal paths, making it suitable for channel interfaces, terminal adapters, and telecommunications equipment that exchange PCM data with a line interface or digital switching system. The 24-pin CDIP package also provides a through-hole construction for systems assembled with conventional axial or DIP-compatible processes. Operation across -40°C to +85°C supports industrial-temperature telecommunications equipment, although the available evidence does not specify a modern automotive qualification. The MC14407L is a legacy Motorola Semiconductor device rather than a contemporary lead-free-focused component. Consequently, engineers should confirm current availability, original construction details, obsolete-material conditions, and revision-specific timing or electrical limits against the manufacturer datasheet and the authorized distributor documentation before committing a new design. Typical uses include PCM switching interfaces, digital telephone terminal equipment, voice-channel converters, telecommunications multiplexers, and embedded systems that need an A-law or mu-law PCM codec. System-level implementation also depends on the connected line-interface or DSP device, clocking arrangement, signal framing, and board-level decoupling specified in the original design documentation. The principal design consideration is that MC14407L is a legacy through-hole codec, so a modern replacement cannot be selected from package size alone. The replacement should be verified for pin-to-pin behavior, clock mode, companding law, power requirements, timing margins, and channel direction. This page synthesizes the verified distributor and datasheet references, sourcing information, and cautious replacement guidance that are not consolidated in a single manufacturer product page.

RFC Hubungi kami
MC145010P Photoelectric Smoke Detector IC | NXP
MC145010P

MC145010P Photoelectric Smoke Detector IC | NXP

The NXP MC145010P is a CMOS photoelectric smoke-detector integrated circuit with an I/O interface, a supply current of 12 µA, and a 16-pin through-hole DIP package. It is designed to operate with an infrared photoelectric chamber and contains the low-power analog and digital circuitry required to evaluate smoke-related optical conditions. The device supports voltage output and includes an interconnectable I/O function for linking smoke-detector units. A photoelectric smoke detector IC is a specialized sensor-interface and signal-processing component. Unlike a simple photointerrupter, it coordinates an infrared light source, an optical chamber, and detection electronics within the broader smoke-alarm system. The MC145010 family belongs to the CMOS integrated-circuit hierarchy and is intended for compact, low-power residential and commercial alarm equipment where response accuracy and standby power are important. The principal operating characteristics include very-low-power CMOS circuitry, a 12 µA supply current, photoelectric input sensing, voltage output, and an I/O pin that can be interconnected with other detector units. The I/O arrangement permits up to 40 units to share common signaling according to the manufacturer documentation. A local smoke condition activates the short-circuit-protected I/O driver to notify remotely connected units and can also support functions such as escape-light activation. Technically, the MC145010P combines analog detection functions with digital control and signaling in one package. The analog section interfaces with the infrared photoelectric chamber, while the digital section manages detector behavior, output signaling, and inter-unit communication. This integration reduces the number of discrete components required in a smoke-alarm design while maintaining a very-low 12 µA supply current. Its 16-pin DIP format also supports through-hole assembly and hand-repairable industrial appliance construction. Typical applications include residential photoelectric smoke alarms, commercial building alarm panels, interconnected multi-unit smoke-detection systems, and low-power safety appliances. The device is particularly appropriate where an infrared chamber is used instead of an ionization chamber and where low standby consumption supports long-lived battery operation. The I/O function can connect detectors across a larger installation so that a local alarm condition can be communicated to remote units. When designing around the MC145010P, follow the manufacturer pin-description and maximum-rating tables when assigning chamber, supply, output, and I/O connections. Preserve the recommended bypass and interconnection arrangements, and verify that the detector’s electrical thresholds match the selected chamber and infrared emitter. Because the I/O line can connect multiple units, check noise immunity, fault propagation, and short-circuit behavior across the completed system. This page organizes the product specifications, sourcing information, application guidance, and verified references for engineers evaluating the MC145010P. It also distinguishes a verified drop-in replacement from related parts that cannot be assumed to share the same footprint, preventing a functionally similar component from being treated as a safe PCB-level substitution.

RFC Hubungi kami
MC145011P Photoelectric Smoke Detector IC | NXP
MC145011P

MC145011P Photoelectric Smoke Detector IC | NXP

NXP Semiconductors MC145011P is a CMOS photoelectric smoke detector interface IC designed for line-powered smoke-detector applications. It accepts an infrared photoelectric chamber, combines very-low-power analog and digital circuitry, and includes an I/O function for detector-system integration. The device is packaged as a 16-pin plastic dual in-line package, identified by the MC145011P ordering code. A photoelectric smoke detector IC is a specialized interface circuit that connects an optical sensing chamber to the rest of an alarm system. Its internal analog and digital sections condition the chamber signal, evaluate smoke-related conditions, and support low-power operation. In the broader device hierarchy, the MC145011P belongs to sensor and detector interface ICs, connecting a physical sensing element to a line-powered embedded alarm system. The principal feature is the CMOS implementation described for the MC145011 family, combining analog signal processing with digital control while emphasizing low power consumption. The IC is intended to operate with an infrared photoelectric chamber rather than relying on a purely ionization-based sensing arrangement. Its I/O capability allows the detector assembly to participate in system signaling and alarm-state control without requiring every function to be implemented by a separate microcontroller. The MC145011 family architecture is intended for compact, battery-conscious alarm products. Low-power operation is particularly important because residential smoke alarms are expected to remain installed for years and often derive operating energy from a line-connected alarm circuit. The integrated analog and digital circuitry reduces the external support circuitry required for optical chamber signal conditioning, threshold evaluation, and system interfacing. Typical applications include residential photoelectric smoke alarms, commercial alarm panels, and other line-powered fire-detection products. A typical design places the MC145011P beside an infrared photoelectric chamber, connects the chamber elements and required timing or filtering components, and uses the I/O interface to communicate with the alarm system. Exact component values, operating limits, timing thresholds, and test points should be selected from the manufacturer application guidance rather than inferred from general smoke-detector practice. Designers should preserve the pin assignment and layout architecture of the original MC145011P design when reusing an existing printed circuit board. The 16-pin plastic DIP package facilitates through-hole assembly and inspection, but its larger footprint differs from modern surface-mount detector-controller packages. Validate chamber sensitivity, alarm thresholds, startup behavior, standby current, and regulatory performance on the final mechanical and optical assembly. This product page combines the identified package and application characteristics with practical guidance for smoke-alarm integration. It also distinguishes the verified MC145011P identity from unconfirmed replacement devices, helping engineers decide when an existing footprint can be reused and when a redesigned detector interface is required.

RFC Hubungi kami
MC145012P Photoelectric Smoke Detector IC | NXP
MC145012P

MC145012P Photoelectric Smoke Detector IC | NXP

The NXP Semiconductors MC145012P is a CMOS photoelectric smoke detector integrated circuit with an I/O interface and temporal-pattern horn driver, designed for use with an infrared photoelectric chamber. Its stated operating voltage range is 6 V to 12 V, its average supply current is 8 µA, and it is supplied in a 16-pin plastic dual in-line package. A photoelectric smoke detector is a safety sensor that detects airborne smoke or other aerosols through light scattering. The MC145012 integrates low-power analog and digital circuitry, an infrared sensing interface, an I/O connection for unit interconnections, and the timing and drive functions required for a pulsed horn. This places the component within the hierarchy of sensor interface IC, smoke detector circuit, alarm-system component, and integrated circuit. The principal functional features are photoelectric chamber support, I/O capability, and temporal-pattern horn drive. The low average supply current of 8 µA is particularly important for battery-backed household alarms because it reduces standby energy consumption. The 6 V to 12 V operating range is compatible with common alarm-system supply arrangements, while the I/O pin provides a path for coordinating interconnected smoke alarms. Internally, the device combines sophisticated very-low-power analog circuitry with digital control and timing functions. Detection occurs when scattered infrared light from smoke particles or other aerosols reaches the sensing input. The detector circuitry evaluates this signal and, upon a detected alarm condition, causes the horn output to follow a pulsating temporal pattern. The manufacturer identifies the circuit as designed for operation in compliance with UL217 and UL268. Typical applications include residential photoelectric smoke alarms, interconnected smoke-alarm networks, commercial building alarm panels, and low-power battery-operated safety products. The same device can serve both single-unit and interconnected alarm designs because its I/O pin supports coordination between multiple detectors, while the horn-driver section provides the required temporal signaling output. A key implementation consideration is the relationship between the chamber, analog signal path, and alarm timing. Component placement, grounding, supply bypassing, and the external chamber interface should follow the manufacturer application circuit to preserve low-noise detection and reliable alarm signaling. The plastic DIP package also requires adequate spacing from heat sources and careful observation of lead orientation during assembly. This product summary consolidates the manufacturer identification, functional description, operating limits, package information, and design intent into an engineering-focused reference. It also distinguishes the MC145012P from generic smoke-detector transistors by documenting its complete photoelectric detection, I/O, and temporal horn-drive roles in one component.

RFC Hubungi kami
MC145017P - Low-Power Ionization Smoke Detector IC | NXP
MC145017P

MC145017P - Low-Power Ionization Smoke Detector IC | NXP

NXP Semiconductors MC145017P is a low-power CMOS ionization smoke detector IC with a temporal-pattern horn driver, a 12 µA supply current, and a 16-pin PDIP package. Designed for use with an external ionization chamber, the device detects smoke, evaluates the chamber signal, and activates an external piezoelectric transducer through its internal horn-driver circuitry. Its operating-temperature range is -10°C to 60°C. An ionization smoke detector is a safety appliance that uses a radiation-based sensing chamber to identify airborne smoke particles. The MC145017 belongs to the sensor and detector interface hierarchy: it accepts an analog signal from the ionization chamber, applies internal detection logic, and controls a piezoelectric alarm. This architecture allows the sensitive ionization chamber, resistive components, and acoustic transducer to remain separate from the monolithic CMOS control circuit. The principal features of the MC145017P include very low 12 µA supply current, CMOS construction, an ionization-sensor input, a voltage output, and a temporal-pattern horn driver for an external piezoelectric transducer. Low supply current is important in battery-operated alarm systems because the detector electronics and sensing chamber must maintain useful standby and alarm performance without imposing excessive load on the backup battery. The MC145017 is designed to operate with an ionization chamber and a small number of external components. According to the NXP MC145017 datasheet, the associated circuit is intended for smoke-detector systems designed to comply with UL217 and UL268 specifications. The temporal horn pattern provides an intermittent alarm signal, while the low-power CMOS control section supports battery-powered installations where standby current is a primary design constraint. Typical applications include residential ionization smoke alarms, commercial smoke-detector modules, and legacy alarm-system replacements that retain the MC145017P pinout. Because the part is listed as obsolete, engineers should treat it primarily as a maintenance component for equipment already built around this device. New smoke-alarm designs should also evaluate current-generation detector ICs against applicable safety requirements rather than assuming an obsolete part can be introduced into a newly certified product. Circuit design requires careful treatment of the ionization-chamber interface, alarm-driver output, supply decoupling, and test points. Keep sensitive input routing away from the piezoelectric drive path, provide the external components specified by the manufacturer, and verify startup, smoke-entry, alarm-sound, and battery-fallback behavior in the complete detector assembly. The 16-pin PDIP package also requires adequate hole spacing and through-hole assembly clearance on the PCB. This page consolidates the MC145017P electrical characteristics, package information, application context, and selection considerations into an engineering-focused guide. It also documents the absence of a verified pin-compatible substitute set and highlights the product's obsolete lifecycle status, helping engineers distinguish usable legacy replacements from components that merely perform a similar smoke-detection function.

RFC Hubungi kami
MC145018P - Low-Power Ionization Smoke Detector IC | NXP
MC145018P

MC145018P - Low-Power Ionization Smoke Detector IC | NXP

The NXP Semiconductors MC145018P is a low-power CMOS ionization smoke detector interface with an interconnect output and temporal horn driver, designed for a 16-pin PDIP package. It accepts an ionization-chamber signal, evaluates smoke-related sensor activity, and drives an external piezoelectric transducer when an alarm condition is detected. The device uses a voltage-output sensor interface and operates with an external ionization chamber and a small number of supporting components. An ionization smoke detector is an electronic system that senses changes in the electrical behavior of an ionization chamber when smoke enters the chamber. The MC145018P belongs to the broader smoke-detector IC category, where it functions as a sensor interface and alarm-control device. Its internal circuitry connects the chamber to the detection electronics, coordinates the alarm signal, and provides a temporal horn-drive output for compatible sounders. The principal features include low-power CMOS operation, an ionization-sensor input, a voltage output, an interconnect function, and a temporal horn driver for an external piezoelectric transducer. The interconnect function supports installation schemes in which multiple detector units can be interconnected. The temporal horn driver provides the required switched drive for the alarm transducer rather than requiring a separate general-purpose driver circuit. The manufacturer identifies the MC145018 family as suitable for smoke-detector systems designed around UL 217 and UL 268 requirements. Its CMOS implementation targets low standby power, an important characteristic for continuously powered household and commercial alarm systems. The 16-pin PDIP package also supports through-hole assembly and inspection of an alarm product that must integrate an ionization chamber, discrete support components, a sound path, and the detector electronics. Typical applications include residential ionization smoke alarms, interconnected commercial alarm panels, portable detector modules, and retrofit assemblies where a legacy through-hole detector interface must be combined with an external piezoelectric horn. In these systems, the MC145018P handles the sensor-to-alarm path while the external chamber and transducer perform the physical sensing and sound-generation functions. Designers should follow the manufacturer datasheet for the ionization-chamber interface, interconnect wiring, external component values, test points, and horn-drive network. PCB layout should keep sensitive chamber connections short and isolated from the switched horn output. Adequate spacing between high-impedance sensor traces and buzzer-drive traces helps reduce false triggering, while correct grounding and stable supply bypassing remain essential for dependable alarm operation. This page organizes the device function, package information, sourcing paths, and design considerations into a focused engineering reference. It also distinguishes verified drop-in alternatives from package or functional substitutes, helping PCB designers avoid assuming that similarly described smoke-detector ICs can share the same footprint and alarm circuitry.

RFC Hubungi kami
MC145026D - 9-Line CMOS Encoder IC | NXP | 16-SOIC
MC145026D

MC145026D - 9-Line CMOS Encoder IC | NXP | 16-SOIC

The NXP Semiconductors MC145026D is a CMOS encoder integrated circuit designed to encode nine information lines and transmit the resulting data serially for remote-control and security applications. It supports nine input lines with either trinary low, high, or open states or binary low and high states, providing 19,683 possible trinary codes. The device is packaged in a 16-pin SOIC surface-mount package. A remote-control encoder IC is part of the broader interface and logic semiconductor hierarchy used to convert physical switch or control states into a compact serial signal. The MC145026D is intended for use with the MC145027 decoder family, allowing an encoded command or access-code word to be transmitted over a wired link and recovered by a compatible receiving circuit. Its repeated transmission behavior increases security by making the received word more resistant to simple single-event transmission errors. The encoder accepts a transmit-enable input to initiate a serial encoding sequence. During normal operation, the nine input pins can represent individual control functions such as multiple button states, access-code positions, or discrete logic conditions. The trinary mode is especially useful for systems that need more than binary combinations, while binary mode can simplify the interface when each control line is restricted to two valid states. The MC145026D is a dedicated encoder rather than a general-purpose microcontroller or communication transceiver. It does not require firmware, and its function is determined by the electrical state of the input pins and the transmit-enable control. This makes it suitable for simple, compact remote-control systems, keypad-based access devices, industrial control panels, and security-related key-entry modules where a hardware encoder is preferable to a programmable controller. As a legacy CMOS logic device, the principal design considerations are operating voltage compatibility, input-state definitions, timing around the transmit-enable signal, and correct receiver pairing. The MC145026D should be used with an appropriate MC145027-family decoder and verified against the NXP datasheet for pin functions, electrical timing, and operating conditions. The part’s documented lifecycle status is obsolete, so new designs should confirm availability and consider a supported alternative before committing to a production release. This page consolidates the manufacturer’s functional description, package information, application guidance, and replacement considerations into a design-focused reference for engineers evaluating the MC145026D in legacy remote-control systems.

RFC Hubungi kami
MC145026P - 9-Line CMOS Encoder | NXP | Remote Control
MC145026P

MC145026P - 9-Line CMOS Encoder | NXP | Remote Control

The NXP Semiconductors MC145026P is a CMOS remote-control encoder with nine input lines, serial data output, and a 16-pin through-hole PDIP package. Each of the nine encoded inputs can represent a low, high, or open state, allowing 19,683 possible codes. A low-level transmit-enable signal starts the transmission sequence, and the encoded word is sent twice to improve communication security. A remote-control encoder is a logic IC that converts a group of physical control inputs into a serial data stream suitable for transmission over a wired or wireless communications link. In the broader product hierarchy, it is a CMOS encoder within the interface-IC and logic-IC categories, connecting human-operated controls to an embedded control, communication, or automation system. The MC145026P forms the transmitting side of the encoder and decoder family described by NXP. The principal features are nine independently encoded lines, three valid logic states per line, support for trinary encoding, and duplicate-word transmission. The active-low transmit-enable input provides a defined event for starting a serial sequence. Because an open state is distinct from low and high, the device can represent more commands with fewer physical input lines than a conventional binary-only encoder. The encoder converts each input combination into a serial codeword and drives its serial output when transmit enable is asserted. During an encoding sequence, the word is transmitted twice, allowing the receiving decoder to reject many transmission errors and recognize repeated valid data. The NXP datasheet identifies the nine inputs as A1 through A5 and A6/D6 through A9/D9, reflecting the family’s support for paired encoder and decoder functions. Typical uses include television remote controls, audio-system command links, industrial pendant controllers, garage-door and access-control transmitters, and low-cost consumer control panels. The device is particularly useful when a design needs a compact command interface with more valid states than a conventional nine-bit binary input would provide, without requiring a separate microcontroller to serialize every button event. When laying out a transmitter, treat the nine command inputs as digital signal lines and keep their traces away from noisy switching nodes. Confirm the electrical levels of the receiver interface and provide suitable pull components for open-state operation. Firmware or hardware should also distinguish a valid repeated word from an incomplete or corrupted transmission before acting on a remote command. This product page combines the NXP manufacturer datasheet, distributor identification, package information, and technical search results with practical guidance for PCB implementation, system pairing, sourcing, and design verification. It also distinguishes the MC145026 encoder from its decoder counterpart and records the absence of a manufacturer-supported pin-compatible substitute.

RFC Hubungi kami
MC145028P - 9-Line CMOS Remote Control Decoder | NXP
MC145028P

MC145028P - 9-Line CMOS Remote Control Decoder | NXP

NXP MC145028P is a CMOS remote-control decoder IC designed for the decoding half of an encoder/decoder pair, with nine address lines, a 16-pin through-hole DIP package, and a 0.300-inch, 7.62 mm body width. It receives a serially encoded command stream, checks the transmitted address, and presents the decoded data and valid-data indication to the associated system controller. A remote-control decoder is a logic IC that translates a serial communication stream into usable control signals. The MC145026, MC145027, and MC145028 devices form encoder/decoder families for remote-control applications. In such a hierarchy, an encoder converts parallel command information into a serial waveform, while a decoder receives that waveform, validates the address information, and reconstructs the data. The MC145028P is therefore a semiconductor interface and logic device rather than a general-purpose microcontroller or analog receiver. The MC145028P supports nine encoded information lines, as described for the MC145026/27/28 encoder-and-decoder family. Its CMOS construction supports low-power remote-control system implementations, while the 16-pin DIP package facilitates through-hole assembly, prototyping, repair, and legacy industrial equipment. The identified package is a 0.300-inch, 7.62 mm 16-DIP configuration. Operating details beyond the package and basic device function require confirmation from the manufacturer datasheet. The decoder is intended to work with a compatible remote-control transmitter, commonly an MC145026 encoder. The transmitter serializes address and command information when its transmit-enable signal is asserted. The receiver reconstructs the transmitted information and indicates whether the received command corresponds to the selected address. This arrangement allows one receiver system to respond selectively to one transmitter or group of transmitters. Typical uses include industrial remote-control panels, access and equipment-control systems, telemetry links, model or process-control interfaces, and legacy embedded systems. The 16-DIP format is especially useful where a through-hole replacement is required, but board area and manual insertion limitations make the device less suitable for compact new portable products. When designing around the MC145028P, match the encoder waveform, address coding, timing, and interface voltage levels rather than selecting the receiver from package appearance alone. Confirm the complete pin assignment and electrical limits in the manufacturer datasheet before routing a new PCB. This page combines device identity, package information, sourcing guidance, application fit, and design cautions for engineers evaluating legacy or repair applications.

RFC Hubungi kami
MC14503BD - Hex 3-State Buffer, 3-18V | onsemi
MC14503BD

MC14503BD - Hex 3-State Buffer, 3-18V | onsemi

The onsemi MC14503BD is a hex non-inverting buffer with six high-impedance, 3-state outputs and two independent disable controls. The device operates from 3 V to 18 V, supports common-bus multiplexing, and is packaged in a 16-pin SOIC for surface-mount assembly. It is designed to provide high current source and sink capability while allowing multiple drivers to share a bus without active output contention. A hex 3-state buffer is a digital logic device that passes each input signal to its corresponding output without inversion. When an output is disabled, it enters a high-impedance state and releases the connected bus line. This tri-state behavior places the MC14503BD in the wider logic-buffer and bus-driver hierarchy, supporting functions from signal isolation and level buffering to bus multiplexing and data-bus sharing. The MC14503B family provides two disable controls. A high level on Disable A places the outputs of buffers 1 through 4 into the high-impedance state, while a high level on Disable B controls the outputs of buffers 5 and 6. This arrangement allows two groups of three outputs to be enabled or disabled independently, which is useful when several devices drive a shared communication or address bus. The 3 V to 18 V operating range makes the MC14503BD suitable for both 5 V and legacy multi-voltage logic systems. Its 16-pin SOIC construction supports compact, high-density PCB layouts while preserving the pin arrangement associated with the MC14503B family. Because the output impedance is high while disabled, only one buffer should actively drive a shared node at a time. Typical uses include bidirectional bus isolation, address decoding, memory-bank selection, peripheral multiplexing, and level translation within mixed-voltage systems. Its non-inverting signal path preserves data polarity, allowing the device to be inserted between a source and destination logic node without changing bus timing or data format. When assigning PCB signals, use the manufacturer pin-description table to confirm the data, disable, supply, and ground connections. Keep the disable traces away from high-current switching nodes, and confirm that every shared output node has exactly one enabled driver during any operating state.

RFC Hubungi kami
MC14503BF - Hex 3-State Non-Inverting Buffer | onsemi
MC14503BF

MC14503BF - Hex 3-State Non-Inverting Buffer | onsemi

onsemi MC14503BF is a hex non-inverting buffer with six 3-state outputs, a 5 V nominal operating voltage, 150 ns propagation delay, and a 16-lead PDIP package. The device provides high-current source and sink capability, making it suitable for common-bus applications where multiple logic devices must share an interconnect. Two independent disable controls allow buffers 1 through 4 and buffers 5 through 6 to be placed in the high-impedance state independently. A 3-state buffer is a digital interface component that can present a valid logic level, actively drive a bus, or electrically release the bus with a high-impedance output. The three-state function distinguishes it from a conventional buffer, which continuously drives its output. By placing several drivers in parallel, a system can reduce contention when only one device is active. The hex organization provides six non-inverting channels in one package. The MC14503BF supports common-bus architectures where source and sink capability must accommodate driven logic levels. Its 150 ns propagation delay provides a defined timing relationship between an input transition and the corresponding output transition. The 50 pF load-capability figure identifies a useful bus-loading condition when evaluating interconnect behavior. Two disable inputs add local bus-segment control without requiring individual output gating at the source logic. The MC14503BF is a bipolar CMOS-family logic device, with the MC14503B family identified by onsemi as a hex non-inverting, 3-state buffer. The two disable controls divide the six buffers into separately controlled groups: Disable A controls buffers 1 through 4, while Disable B controls buffers 5 through 6. This arrangement permits a compact implementation of segmented shared buses, bidirectional-looking bus translators built from unidirectional channels, and systems that require a driver to relinquish a line during another device's transfer cycle. Typical uses include microprocessor and microcontroller bus isolation, memory-module data buses, peripheral port expansion, test-interface routing, and industrial control systems with shared parallel data paths. The device is particularly relevant when one group of four channels must disengage together while another group of two channels remains active. The package also provides through-hole mechanical compatibility with conventional 16-pin logic-board layouts. For reliable operation, design the disable signals so that no two devices actively drive the same shared node simultaneously. Account for output propagation delay when establishing bus ownership timing, and keep signal routing short enough to limit capacitive loading. Because the device includes a high-impedance state, the disable logic must actively establish every required output state rather than relying on floating control inputs. This product page combines the functional description, technical attributes, sourcing information, interface use cases, and design guidance needed to evaluate the MC14503BF. It also organizes drop-in alternatives and engineering trade-offs so designers can determine whether the original part remains the best fit before modifying a PCB or changing the bus architecture.

RFC Hubungi kami
MC14510BF - BCD Up/Down Counter | onsemi | Logic IC
MC14510BF

MC14510BF - BCD Up/Down Counter | onsemi | Logic IC

The onsemi MC14510BF is a BCD up/down counter integrated circuit, also categorized as a counter and divider, and is offered in a flat-package configuration. Its core function is to count upward or downward through a decade and preserve the count in BCD format, making it suitable for sequencing, timing, and event-counting systems that require decimal-compatible logic rather than ordinary binary counting. The MC14510BF belongs to the broader 4000-series CMOS logic family, where counter ICs operate as state-management building blocks inside larger digital control systems. A BCD up/down counter is a specialized type of counter IC that advances or reverses through ten states from zero through nine. This decimal-oriented behavior can simplify the interface between digital logic and ten-position displays because each decade is represented by four BCD output bits. The counter can therefore support decade-stepping, programmable timing, and sequential control functions. By contrast, a conventional binary counter advances through 16 states per four output bits, which may require additional conversion when a decimal display or decade-oriented mechanism is involved. The MC14510BF uses four parallel BCD outputs to represent the current count. Typical system use requires a clock source, control logic for count direction, reset or initialization handling, and suitable decoupling close to the power terminals. Because the part belongs to the MC14510B family, designers should consult the family datasheet for the exact electrical limits, truth table, propagation timing, supply-voltage range, and pin assignments before finalizing a PCB. MC14510BF is suitable for industrial sequencing equipment, laboratory timers, digital panel meters, test fixtures, event counters, and embedded control subsystems. In a timer or sequencer, the up/down capability allows the same counter to advance through timing intervals or reverse when a control event requests a return to the starting state. In an instrument, the BCD outputs can feed display-driver circuitry without requiring the system controller to perform repeated binary-to-BCD conversion. PCB implementation should follow the package drawing and pin-description table in the onsemi family datasheet. Place the decoupling capacitor close to the supply and ground connections, route clock and control traces away from noisy analog or switching-power nodes, and use a consistent ground-return path. Decoupling requirements, operating voltage, and maximum clock frequency must follow the official family documentation rather than assumptions based on another package or counter variant. This product page combines the device identity, package information, application guidance, comparison structure, and practical design considerations needed to plan a replacement or redesign. It also separates confirmed device facts from parameters that require verification against the manufacturer datasheet, helping engineers create a reproducible design review before committing the counter to a new PCB.

RFC Hubungi kami
MC14516BD - 3-18V Binary Up/Down Counter | onsemi
MC14516BD

MC14516BD - 3-18V Binary Up/Down Counter | onsemi

The onsemi MC14516BD is a synchronous 4-bit binary up/down counter built with MOS P-channel and N-channel enhancement-mode devices in a monolithic structure. It operates from a 3.0 Vdc to 18 Vdc supply, uses a 16-SOIC package, and includes diode protection on all inputs. The synchronous architecture allows the counting stages to change together rather than operating as separate ripple counters. A binary up/down counter is a digital logic component that increments or decrements a four-bit numerical state according to direction-control and clock inputs. It belongs to the counter and arithmetic-function hierarchy within CMOS logic ICs. The MC14516BD is useful when a digital system must track a sequence in either direction, such as positioning, timing, indexing, or state progression, while retaining the familiar parallel binary-counter interface. Key features include a 3.0 Vdc to 18 Vdc supply range, internal synchronous operation for high-speed counting, and diode protection on every input. These characteristics make the device appropriate for general-purpose digital control, clocked sequencing, and count-direction control. The 16-SOIC package is a surface-mount format that supports conventional reflow assembly and PCB routing without requiring a through-hole footprint. The counter uses MOS P-channel and N-channel enhancement-mode devices in a monolithic implementation. Its internal synchronous operation provides coordinated state transitions when the clock advances the count. Direction control determines whether the binary output increments or decrements, allowing two counting behaviors to share one counter block. The manufacturer describes the circuit as a binary up/down counter and identifies all inputs as protected by diodes. Typical applications include digital position and step tracking, programmable event counters, industrial sequencing logic, instrumentation timers, and control systems that need a reversible binary count. In these systems, the synchronous counter can be clocked from a defined timing source while external control logic selects count direction or clears the state. The broad 3.0 Vdc to 18 Vdc supply range accommodates both low-voltage CMOS logic and higher-voltage industrial interface environments. Designers should use the manufacturer pin-description and connection diagrams when assigning PCB nets and should not infer inactive or reserved pins from abbreviated online descriptions. Input transitions, clock timing, reset behavior, and output-state requirements must be verified against the MC14516BD datasheet before high-speed operation. Decoupling practice should also follow the voltage rails used in the final system and the manufacturer application guidance. This product page consolidates the verified device identity, supply range, synchronous-counter construction, protected-input feature, package information, source links, and same-footprint family alternatives. It also provides application guidance and engineering checks that support faster part selection without replacing the complete manufacturer datasheet.

RFC Hubungi kami
MC14516BF - 4-Bit Synchronous Up/Down Counter | onsemi
MC14516BF

MC14516BF - 4-Bit Synchronous Up/Down Counter | onsemi

The onsemi MC14516BF is a 4-bit synchronous binary up/down counter built with complementary P-channel and N-channel enhancement-mode MOSFETs in a monolithic structure. It operates from a 3.0 V to 18 V supply, provides input diode protection, and is offered in a 16-pin SOP package. The counter can be incremented or decremented synchronously and can be loaded with a parallel preset value for deterministic control sequences. A synchronous binary counter is a sequential logic device that advances or reverses its four-bit output state on each active clock transition. The MC14516BF belongs to the broader CMOS counter hierarchy, where counter ICs provide repeatable digital state generation for timing, sequencing, arithmetic, and industrial control. Unlike a simple ripple counter, its internally synchronous architecture coordinates state transitions for predictable operation in clocked digital systems. The primary features of the MC14516BF include a 3.0 V to 18 V supply range, internal synchronization, diode protection on all inputs, and four preset inputs. Preset data can be loaded into the counter by applying the desired binary value and asserting the preset-enable control. This combination supports repeatable initialization, programmable step sequences, and compact state management in systems that need more flexibility than a fixed modulus counter. Internally, the monolithic construction combines P-channel and N-channel enhancement-mode MOSFETs. The four output bits represent the current count, while separate direction, clock, preset-enable, and preset-data controls allow the system designer to choose between counting and parallel loading. Because the device operates from 3.0 V through 18 V, it can be used with both low-voltage digital systems and higher-voltage industrial control environments, subject to the input and output limits in the manufacturer datasheet. Typical applications include industrial sequence controllers, programmable timing modules, digital instrumentation, batch-counting equipment, and control systems that periodically divide an event stream into groups. The counter is also useful in laboratory and test equipment where a repeatable four-bit state must advance at each clock edge. A design can use the outputs as address bits, time-slot indicators, step markers, or binary control signals. For reliable implementation, review the manufacturer pin-description table and the input transition and timing diagrams before assigning logic levels. Account for setup and hold requirements around the clock, direction, and preset controls. Ensure unused inputs are connected to a defined valid state and include reset or preset sequencing in the controller startup routine. The 16-pin SOP footprint also requires an appropriate land pattern and adequate clearance between adjacent copper features. This product page combines the manufacturer function description with practical sourcing, replacement, pinout-location, and circuit-integration guidance. It also distinguishes documented device characteristics from parameters that still require verification against the latest ON Semiconductor datasheet, helping engineers move from selection to schematic capture with fewer component-level questions.

RFC Hubungi kami
MC145170D2 - 185MHz PLL Frequency Synthesizer | NXP
MC145170D2

MC145170D2 - 185MHz PLL Frequency Synthesizer | NXP

NXP Semiconductors MC145170D2 is a single-chip PLL frequency synthesizer with a maximum operating frequency of 185 MHz, supplied in a 16-pin SOIC package. It combines fully programmable R and N counters, an input amplifier, crystal-oscillator support, a programmable reference output, and both single-ended and double-ended phase detectors. The double-ended detector uses a linear transfer function without a dead zone, making the device suitable for precision phase-control and frequency-generation systems. A phase-locked loop, or PLL, is a feedback-controlled timing circuit that locks an output frequency to a reference frequency. The PLL frequency synthesizer category sits within clock and timing integrated circuits, where it supports clock generation, frequency multiplication, modulation, and phase alignment. The MC145170 family was designed for direct use in MF, HF, and VHF bands, combining digital counters and analog phase-detection functions on one integrated circuit. Programmable R and N counters allow the relationship between the reference input and synthesized output to be established by register programming. The device supports an external crystal at the input amplifier, while the programmable reference output provides a convenient reference for other system blocks. Its maximum specified quiescent supply current remains 100 μA, making it practical for low-power frequency-control equipment when the operating conditions permit low current consumption. The MC145170-2 uses a more responsive power-on reset circuit than MC145170-1. According to NXP, both devices use the same chip with different power-on-reset mask options, and the MC145170-2 is recommended for new designs. This reset behavior is especially useful when a brief supply interruption could otherwise leave internal counters or the phase comparator in an incorrect state. The MC145170-2 is also identified as pin-for-pin compatible with MC145170-1. Typical uses include local-oscillator generation in radio receivers and transmitters, FM and phase-modulation systems, frequency-agile communications equipment, industrial instrumentation, and low-power RF test equipment. The 185 MHz operating limit provides useful range for VHF designs, while the 16-pin SOIC package supports conventional surface-mount assembly. System designers should account for the required loop filter, reference source, divider programming, and decoupling network shown in the manufacturer’s application guidance. For a new design, confirm that the selected reference frequency, counter ratio, loop bandwidth, and required reference output can be supported by the internal divider arrangement. Place the input and reference-network components close to their associated pins, use a clean and stable reference source, and verify startup and reacquisition behavior across supply interruptions. The D suffix denotes the 16-pin SOIC ordering option identified by the product listing. This page combines the manufacturer’s device capabilities, package information, family compatibility details, application guidance, and drop-in replacement analysis. It also organizes the most important selection constraints into a practical guide for evaluating the MC145170D2 in PLL-based RF and timing designs.

RFC Hubungi kami
MC14521BD - 24-Stage Frequency Divider | onsemi
MC14521BD

MC14521BD - 24-Stage Frequency Divider | onsemi

onsemi MC14521BD is a 24-stage CMOS frequency divider with a 16-pin SOIC package, capable of dividing an input frequency by up to 2^24, or 16,777,216. Its input circuit supports crystal-oscillator, RC-oscillator, and external-oscillator operating modes. Each successive flip-flop divides the preceding frequency by two, making the device suitable for long-duration timing, pulse-rate division, and low-frequency clock-generation systems. A frequency divider is a counter or logic IC that reduces one clock frequency to a lower, predictable frequency. The MC14521BD belongs to the CMOS counter-and-divider hierarchy, where a chain of bistable stages forms a ripple-style binary frequency reduction network. The 24-stage count provides a much longer division interval than ordinary binary counters, allowing a relatively high-frequency timing reference to produce a slow event rate without a microcontroller or complex divider array. The key features of the MC14521BD include 24 internal flip-flops, three selectable input operating modes, division by two per stage, and a maximum count of 16,777,216. Its 16-lead SOIC package supports conventional surface-mount assembly. The D suffix identifies the particular onsemi device grade, while the MC14521B family datasheet describes the common divider architecture and electrical characteristics used to evaluate the MC14521BD. Internally, the input section can operate as a crystal oscillator, an RC oscillator, or a buffer for an externally supplied oscillator signal. This flexibility allows the circuit designer to establish a self-contained timebase or use a cleaner reference already present elsewhere in the system. Each flip-flop divides the frequency of the preceding stage by two, creating a binary sequence across the divider chain and supporting applications that require long count intervals or periodic pulse generation. Typical uses include low-frequency clock generation, industrial timer modules, laboratory pulse generators, frequency-counting instruments, event-rate reduction, and embedded timing references. In an oscillator arrangement, the device can replace a bank of discrete divider flip-flops. When driven from an external oscillator, the same package provides a compact way to reduce a reference clock to a rate suitable for counters, displays, or slow sequencing circuits. Designers should verify the selected crystal or RC network against the operating conditions in the MC14521B datasheet and confirm that the oscillator starts and remains stable over the intended temperature and supply range. Decoupling should be placed close to the supply pins, unused inputs should be held at defined logic levels, and output timing should be checked for the propagation delay accumulated through 24 stages. The maximum operating frequency and output-drive capability must also be considered in the final timing design. This product page combines the verified divider architecture, package information, application guidance, replacement analysis, and practical design considerations in one engineering-focused reference. It helps designers identify the correct operating mode, understand the binary count limit, and distinguish a genuine same-footprint replacement from a merely similar counter before committing a new PCB revision.

RFC Hubungi kami
MC14521BF - 24-Stage Binary Frequency Divider | onsemi
MC14521BF

MC14521BF - 24-Stage Binary Frequency Divider | onsemi

onsemi MC14521BF is a 24-stage binary frequency divider and counter IC with a 16-pin PDIP package. Its internal architecture contains 24 flip-flops, each dividing the frequency of the preceding stage by two, allowing the device to count through 2^24 states, or 16,777,216. The input circuit supports three operating modes: crystal oscillator, RC oscillator, and buffered external-oscillator input. A binary frequency divider is a sequential logic device that reduces an input clock frequency by a fixed integer factor. The MC14521B belongs to the counter and multivibrator family of CMOS logic ICs, placing it within the broader semiconductor hierarchy of sequential logic, counters, frequency dividers, and clock-management circuits. Unlike a programmable divider or phase-locked loop, it implements a fixed divide-by-2^24 ratio at its output while retaining a simple external clocking architecture. The principal feature of the MC14521BF is its 24-stage flip-flop chain. Each successive stage operates at one-half the frequency of the preceding stage, enabling a clock input to be divided into a substantially lower-frequency output. The manufacturer describes three input configurations: a crystal oscillator, an RC oscillator, or an input buffer for an externally supplied oscillator. These configurations give designers flexibility when creating stable timing references or dividing an existing system clock. The internal counting architecture advances on each active clock transition. The 24-bit count range reaches 16,777,216, which makes the device useful for long timing intervals, fixed-ratio clock generation, event counting, and low-frequency timing references. Its fixed binary ratio differs from general-purpose programmable counters and makes system timing easier to analyze when a known divide factor is required. Typical uses include timer and delay networks, pulse-rate reduction, instrumentation clocks, sequential test systems, low-frequency waveform generation, and digital timing references. In an RC or crystal-oscillator implementation, the device can establish its own timing source; with the buffered external-oscillator mode, it can instead divide a clock already present elsewhere in the system. Designers should select the appropriate oscillator components and confirm the device’s electrical limits, supply requirements, and timing characteristics against the manufacturer datasheet before implementation. PCB layout should keep oscillator and timing paths compact, maintain a defined ground reference, and separate sensitive timing nodes from noisy switching circuits. The 16-pin PDIP package is suitable for through-hole assembly and prototype or legacy industrial equipment where a large package is acceptable. This page combines the manufacturer function description, package and pin-count information, architecture details, application guidance, and a transparent assessment of drop-in replacement options. It also distinguishes the uniquely ordered MC14521BF ordering code from generic family references and focuses design decisions on the fixed 24-stage division behavior.

RFC Hubungi kami