Produk (44,000+)

MC33078D - Dual Low-Noise 15MHz Op Amp | Texas Instruments
MC33078D

MC33078D - Dual Low-Noise 15MHz Op Amp | Texas Instruments

The Texas Instruments MC33078D is a bipolar dual operational amplifier with two independent amplifiers, 4.5 nV/√Hz input-voltage noise, a 15 MHz gain-bandwidth product, and a 7 V/µs slew rate. The device is supplied in an 8-pin SOIC package and is intended for audio and data-signal applications operating from -40 °C to 85 °C. A dual operational amplifier combines two amplifiers in one package, providing a practical path from analog signal conditioning to broader voltage-amplifier and analog IC functions. Each channel can amplify, buffer, filter, or drive a defined analog signal when used with suitable external components. MC33078D is particularly useful where low noise, wide bandwidth, and fast large-signal response are more important than the very low power consumption associated with CMOS-only amplifiers. The MC33078D uses bipolar technology, which supports low-noise operation and audio-focused performance. Its 4.5 nV/√Hz input-noise figure is suited to high-fidelity audio preamplification, microphone-stage signal conditioning, and low-level instrumentation. A 15 MHz gain-bandwidth product supports higher closed-loop bandwidth than slower general-purpose precision amplifiers, while the 7 V/µs slew rate provides improved ability to reproduce large-amplitude signals without excessive distortion. Two independent channels in one package reduce board area for balanced, differential, or multi-stage analog circuits. The 8-pin SOIC (D) package uses a familiar surface-mount footprint and supports automated assembly. Because its dual topology is not rail-to-rail by specification, applications must account for the allowable input and output voltage ranges when using single-supply or dual-supply configurations. Decoupling and stable feedback-network design remain essential for low-noise performance. Typical uses include stereo audio input amplification, active equalization, low-level sensor conditioning, line-stage amplification, and mixed-signal filtering. The two channels may also implement separate gain blocks, buffers, or active filters when the required common-mode range and output swing fit the application. In audio designs, low-noise operation helps preserve quiet signal paths, while the 15 MHz bandwidth and 7 V/µs slew rate provide headroom for detailed waveform reproduction. When laying out the circuit, place the power-supply bypass capacitor close to the supply pins and keep feedback resistors and input components compact to minimize parasitic capacitance and noise pickup. Verify gain-bandwidth and stability requirements with the actual noise-gain network. Single-supply operation may require biasing or AC coupling if the source cannot reach ground, so confirm the input common-mode range before finalizing the schematic. This product page combines manufacturer specifications, package information, practical analog-design guidance, and verified drop-in alternatives. It also highlights the exact differences between same-manufacturer and cross-manufacturer options, helping engineers compare compatibility, bandwidth, noise, temperature range, and application fit before making a board-level replacement decision.

RFC Hubungi kami
MC33078N - Dual Low-Noise 15MHz Op Amp | STMicroelectronics
MC33078N

MC33078N - Dual Low-Noise 15MHz Op Amp | STMicroelectronics

STMicroelectronics MC33078N is a monolithic dual bipolar operational amplifier optimized for low-noise audio and data-signal applications. The device provides two amplifiers, 4.5 nV/√Hz voltage-noise density, a 15 MHz gain-bandwidth product, and a 7 V/µs slew rate in an 8-pin Mini DIP package. It supports both single-supply and dual-supply operation, allowing its dual amplifier to process audio channels or implement gain, filtering, buffering, and signal-conditioning functions. An operational amplifier is a high-gain differential amplifier whose inverting and non-inverting inputs are compared to produce an amplified output. The bipolar input stage of the MC33078N combines low voltage noise with a wide gain-bandwidth product and high slew rate. In the broader semiconductor hierarchy, the MC33078N is an analog amplifier IC, more specifically a dual low-noise operational amplifier used in audio, instrumentation, and general-purpose signal-processing circuits. The principal performance features include 4.5 nV/√Hz input-voltage noise, 15 MHz gain-bandwidth product, and 7 V/µs slew rate. Its two amplifier channels provide design economy in stereo audio preamplifiers, active filters, line drivers, and instrumentation. The 8-pin Mini DIP package is also suitable for through-hole construction and prototyping where dual-line access and straightforward manual assembly are useful. The bipolar architecture provides the fast large-signal response needed for audio signals while retaining low noise for microphone-level and line-level work. The 15 MHz gain-bandwidth product supports wider closed-loop bandwidth than a low-frequency general-purpose amplifier, while the 7 V/µs slew rate helps the device reproduce large-amplitude waveforms without excessive distortion. Supply topology determines the usable common-mode and output-voltage ranges, so single- and dual-supply circuits require different biasing arrangements. Typical applications include stereo audio preamplification, active crossover and equalization networks, microphone preamplifiers, line-level buffers, active filters, sensor signal conditioning, and general dual-channel analog processing. In stereo equipment, the two channels can process left and right signals independently, reducing component count and helping maintain matched channel layouts. For new PCB designs, place the decoupling capacitor close to the supply pin and connect the exposed return path directly to the ground plane. When replacing an existing MC33078 footprint, verify the exact power-supply range, common-mode limits, output swing, noise characteristics, and stability requirements rather than relying only on the DIP-8 outline. This page combines manufacturer specifications, cross-reference information, practical application guidance, and package-aware replacement analysis to support faster engineering evaluation and sourcing.

RFC Hubungi kami
MC33078P - Dual 16MHz Low-Noise Op Amp | Texas Instruments
MC33078P

MC33078P - Dual 16MHz Low-Noise Op Amp | Texas Instruments

The Texas Instruments MC33078P is a bipolar dual operational amplifier with 16 MHz gain-bandwidth product, a 7 V/µs slew rate, and 4.5 nV/√Hz input voltage noise, supplied in an 8-pin PDIP package. The device supports single-supply and dual-supply operation over a voltage range of ±5 V to ±18 V and is intended for quality audio and data-signal processing applications. An operational amplifier is an analog signal-conditioning IC that uses high-gain differential amplification to increase the voltage difference between two inputs. In the wider hierarchy, an op amp belongs to amplifiers, analog integrated circuits, and signal-chain conditioning devices. The MC33078P contains two independent amplifiers in one package, allowing one package to serve two channels while reducing board area and simplifying dual-audio or dual-data-signal designs. The MC33078/9 family uses bipolar transistor technology with high-frequency PNP input transistors. This architecture provides low input voltage noise, high gain-bandwidth product, high slew rate, low total harmonic distortion of 0.002%, and a low input offset voltage of 0.15 mV. These characteristics make the amplifier suitable for audio preamplification, filtering, instrumentation, and general-purpose analog signal conditioning where both small-signal fidelity and bandwidth are important. The two channels operate independently from the same supply pins. Its 16 MHz gain-bandwidth product allows useful closed-loop bandwidth well below the unity-gain frequency, while the 7 V/µs slew rate supports faster large-signal transitions than many general-purpose bipolar op amps. Noise and distortion figures should therefore be evaluated in the same signal bandwidth and output amplitude used in the target circuit; headline values do not describe complete system performance by themselves. Typical uses include microphone and line-level audio amplification, active filters, analog instrumentation, low-level sensor conditioning, and dual-channel signal processing. The 8-pin PDIP package is suitable for through-hole construction, prototyping, repair work, and applications where the larger package is acceptable. Local bypass capacitors close to the supply pins remain important for stable operation and low-noise performance. The principal design trade-off is package size rather than electrical capability: PDIP-8 is easy to install manually but occupies more PCB area than surface-mount dual-op-amp packages. Designers should preserve adequate output-current headroom for capacitive loads, verify stable operation with the selected feedback network and load, and avoid assuming that low-noise input devices are interchangeable with FET-input amplifiers because bias-current and distortion behavior differ. This page consolidates the verified manufacturer specifications, distributor availability references, and engineering-focused selection guidance for MC33078P. It also distinguishes documented MC33078-family options from true pin-compatible replacements, helping engineers avoid treating merely similar amplifiers as drop-in substitutes.

RFC Hubungi kami
MC33079D - 15 MHz Low-Noise Quad Op Amp | onsemi
MC33079D

MC33079D - 15 MHz Low-Noise Quad Op Amp | onsemi

onsemi MC33079D is a low-noise, quad operational amplifier with four amplifiers in a 14-pin SOIC package. Its headline specifications are 4.5 nV/√Hz voltage-noise density, a 15 MHz gain-bandwidth product, and a 7 V/µs slew rate. The MC33079 uses bipolar input transistors and is intended for audio and data-signal processing applications requiring low noise, high-frequency response, low distortion, and stable operation. An operational amplifier, or op amp, is a high-gain differential amplifier whose external feedback defines its gain and bandwidth. Within the semiconductor hierarchy, an op amp belongs to the linear amplifier and analog signal-conditioning categories. It is used to amplify weak sensor signals, buffer high-impedance sources, implement active filters, and provide gain in audio and control paths. The MC33079 integrates four amplifiers in one package, reducing board area while providing consistent device-level matching. The MC33079D combines 4.5 nV/√Hz low-voltage-noise performance with a 15 MHz gain-bandwidth product. Its 7 V/µs slew rate supports faster large-signal transitions than slower general-purpose amplifiers. Additional features include 0.002% distortion, a large output-voltage swing, 2 kV ESD protection, and a macromodel for simulation. These characteristics make the device relevant to microphone preamplification, active audio crossover networks, audio buffer stages, and precision low-frequency signal conditioning. The bipolar architecture uses high-frequency PNP input transistors to provide low input-voltage noise. Because the amplifiers are not rail-to-rail, system designers should verify input common-mode range and output swing against the selected supply voltage. The listed operating-voltage range of 2.5 V to 15 V permits operation from low-voltage analog systems through conventional ±15 V bipolar supplies. The four amplifiers share a common package, although each output still requires suitable output-current and stability analysis for its load. Typical uses include four-channel audio buffering, low-level microphone amplification, active equalization, filtering, instrumentation interfaces, and general-purpose analog signal processing. In multi-amplifier designs, adjacent channels can implement gain, filtering, and drive functions without requiring four separate packages. The device can also serve in laboratory and industrial control circuits where low noise and a 15 MHz bandwidth are more important than rail-to-rail input or output operation. The primary design consideration is power-supply configuration. Decouple each supply connection with a local ceramic bypass capacitor, maintain a short return path, and place input and feedback components close to the relevant amplifier pins. Avoid using the quad amplifier merely because four circuits are required: confirm common-mode limits, output-swing headroom, capacitive-load stability, noise-gain bandwidth, and channel-to-channel layout symmetry before releasing the PCB. This product record combines the MC33079D manufacturer-datasheet specifications, package information, search queries, and cross-reference findings with practical design guidance. It also highlights genuine replacement constraints: a mechanically similar 14-pin SOIC amplifier is not automatically a drop-in replacement, so common-mode range, bias current, stability, noise, and exact pin assignment must be checked before substitution.

RFC Hubungi kami
MC33079DG - 16MHz Low-Noise Quad Op Amp | onsemi
MC33079DG

MC33079DG - 16MHz Low-Noise Quad Op Amp | onsemi

The onsemi MC33079DG is a low-noise, general-purpose quad operational amplifier with four amplifiers per package, a 16 MHz gain-bandwidth product, a 7 V/us slew rate, and a 14-pin SOIC package. It operates from ±2.5 V to ±9 V, with a maximum operating voltage of ±18 V, making it suitable for dual-rail audio, instrumentation, and general signal-processing systems. An operational amplifier is an active analog component that uses negative feedback to amplify the difference between two input voltages. The quad configuration places four amplifiers in one package, reducing board area for multichannel audio preamplifiers, sensor-conditioning circuits, active filters, and low-level signal-processing systems. The MC33078/79 family uses bipolar circuitry and high-frequency PNP input transistors to combine low input-voltage noise with useful high-frequency performance. The MC33079DG provides 4.5 nV/sqrt(Hz) voltage-noise density, a 16 MHz gain-bandwidth product, and a 7 V/us slew rate. Its typical harmonic-distortion figure is 0.002%, while common-mode rejection is 80 dB. The low-noise input stage is particularly useful when amplifying weak signals from microphones, sensors, and audio sources without adding unnecessary broadband noise. The output stage supports large voltage swings for improved dynamic range in line-level circuits. The amplifier's 16 MHz bandwidth makes it suitable for signal paths operating well above the audio band. Its 7 V/us slew rate also allows comparatively rapid transitions when driving higher-impedance loads. The family specification identifies ESD protection of 2 kV, a macromodel for circuit simulation, and excellent frequency stability. These characteristics make the device suitable for precision audio, active filtering, low-level instrumentation, and mixed analog-signal processing. Typical uses include four-channel audio preamplification, microphone conditioning, active low-pass or band-pass filters, buffered sensor outputs, and general-purpose dual-supply amplification. Because all four amplifiers share one package, PCB space and supply routing can be organized efficiently. The 14-SOIC outline is also convenient for through-hole assembly and conventional prototype-board layouts. Design with adequate supply decoupling near pins 4 and 11 and confirm that the required output swing remains inside the amplifier's operating limits. The 80 dB common-mode rejection helps reject common-mode interference, but input and output layout still determines actual system noise performance. Avoid excessive capacitive loading because it can reduce stability and alter the practical slew rate. This product summary combines the manufacturer amplifier specifications, package information, operating limits, drop-in family options, and practical design guidance. It also distinguishes electrical and packaging variants so engineers can identify a suitable replacement without changing the 14-SOIC footprint.

RFC Hubungi kami
MC33079DT - Low-Noise Quad Op Amp | STMicroelectronics | Audio
MC33079DT

MC33079DT - Low-Noise Quad Op Amp | STMicroelectronics | Audio

The STMicroelectronics MC33079DT is a monolithic quad operational amplifier designed for low-noise audio signal paths, featuring 4.5 nV/√Hz voltage noise, a 15 MHz gain-bandwidth product, and a 7 V/µs slew rate. The device is packaged in a 14-pin SOIC for surface-mount production assemblies. Four amplifiers in one package reduce board area and simplify multi-channel audio circuitry. An operational amplifier is a voltage-gain circuit element used to amplify small signals while improving impedance characteristics. The MC33079 belongs to the low-noise operational-amplifier family within the broader linear-amplifier and signal-conditioning hierarchy. Its low-noise input stage is particularly useful when the amplified signal originates from microphones, pickups, sensors, or line-level audio sources. The four internal amplifiers share a common supply architecture and are intended for low-voltage audio applications. Key performance characteristics include 4.5 nV/√Hz input-voltage noise and 15 MHz gain-bandwidth product. The 7 V/µs slew rate supports faster signal transitions, while the manufacturer reports very low distortion of 0.002%. These characteristics make the device suitable where low noise, bandwidth, and signal fidelity must coexist in a compact package. MC33079DT is a general-purpose quad amplifier rather than a dedicated audio-output driver. Each amplifier includes the conventional non-inverting and inverting inputs, an output, and supply pins. The SOIC-14 package provides a practical surface-mount option for industrial and consumer audio boards, active crossovers, preamplifiers, mixers, and instrumentation. Its four-channel organization makes it suitable for multichannel systems requiring consistent amplifier performance. Typical uses include microphone preamplification, line-level buffering, active equalization, audio summing, and low-level sensor amplification. Designers should select suitable input and feedback networks based on the required noise gain, bandwidth, and output swing. The signal source and load must also be checked against the device's supply-voltage and common-mode limits before layout begins. For PCB implementation, place input and output paths to minimize parasitic capacitance and keep feedback resistors close to the relevant amplifier pins. Decoupling capacitors should be positioned near the supply pins, while analog and high-impedance traces should remain away from switching nodes. Stable feedback ratios and clean grounding are especially important when low-level audio noise must remain below the source's own noise floor. This page combines the MC33079DT's documented noise, bandwidth, slew-rate, distortion, and package characteristics with application-focused guidance, pin-compatible replacement analysis, and practical PCB considerations for evaluating the amplifier in new or existing audio designs.

RFC Hubungi kami
MC33079N - Low-Noise Quad Op Amp | STMicroelectronics | Audio
MC33079N

MC33079N - Low-Noise Quad Op Amp | STMicroelectronics | Audio

STMicroelectronics MC33079N is a monolithic quad operational amplifier designed for audio and general signal-processing applications, with four amplifiers in a 14-pin DIP package. Its headline characteristics are 4.5 nV/√Hz voltage noise, a 15 MHz gain-bandwidth product, and a 7 V/µs slew rate. The device is intended for designs that require low-noise signal amplification with sufficient bandwidth to handle audio signals and other low-frequency waveforms. An operational amplifier is a voltage-gain building block used throughout analog electronics. The MC33079 belongs to the op-amp hierarchy, where it provides amplification, buffering, filtering, and active gain for analog signals. Its four amplifiers share a common power supply in one package, allowing one quad device to implement several stages of an audio preamplifier, mixer, line amplifier, or measurement circuit while reducing board area. The MC33079N combines low voltage noise with high-frequency performance. The 4.5 nV/√Hz noise density supports low-noise audio amplification, while the 15 MHz gain-bandwidth product provides useful bandwidth for audio-frequency closed-loop designs. A 7 V/µs slew rate supports large-signal reproduction and reduces the likelihood of slew-rate distortion in higher-gain stages. The manufacturer also specifies very low distortion of 0.002%, along with strong phase and gain margins. Its four-circuit organization provides flexibility for mixed-signal layouts. Each amplifier can perform a separate function, such as input amplification, active filtering, buffering, or output drive, when the system does not require all four stages simultaneously. Since this is an analog integrated circuit, its performance depends on suitable bypass capacitors, stable feedback networks, appropriate source and load impedances, and careful consideration of common-mode and output-voltage limits. Typical uses include stereo and multichannel audio preamplification, active crossover networks, microphone and line-level signal conditioning, servo-control loops, and instrumentation requiring multiple amplifiers. The quad format can also reduce component count by replacing several individual single or dual amplifier packages. Where an existing amplifier section uses an equivalent 14-pin quad footprint, the MC33079N can serve as a focused upgrade for lower-noise audio operation after checking pin functions and operating limits. Design the supply rails to remain within the device's operating requirements and place the bypass capacitors close to the power pins. Keep feedback loops short, use resistors and capacitors suitable for the intended audio bandwidth, and verify stability with the selected gain and load. An oscilloscope measurement of output clipping, noise, and slew behavior can confirm that the overall circuit, rather than the op amp alone, meets the system specification. This page organizes the MC33079N's principal electrical characteristics, package details, application guidance, drop-in replacement options, and engineering trade-offs. It is designed to help engineers evaluate noise, bandwidth, slew rate, distortion, and compatibility before integrating the amplifier into an audio or precision analog design.

RFC Hubungi kami
MC33079PG - Quad 16 MHz Low-Noise Op Amp | onsemi
MC33079PG

MC33079PG - Quad 16 MHz Low-Noise Op Amp | onsemi

The onsemi MC33079PG is a low-noise, general-purpose quad operational amplifier fabricated with bipolar technology and optimized for audio and data-signal processing. The device contains four amplifiers in a 14-pin PDIP package and operates from a 5 V to 18 V supply. Its headline specifications include a 16 MHz gain-bandwidth product, a 7 V/µs slew rate, and low-noise bipolar input stages using high-frequency PNP input transistors. An operational amplifier is a voltage-controlled, high-gain differential amplifier used to amplify small input signals and drive higher-level circuits. Within the semiconductor hierarchy, an op amp belongs to the amplifier IC and analog signal-processing categories. The MC33079 combines four amplifiers in one package, reducing board area when a design requires multiple gain stages, buffers, summing amplifiers, or active filters. The MC33079PG offers a 16 MHz gain-bandwidth product and a 7 V/µs slew rate. These figures make it suitable for audio preamplification, active filtering, signal conditioning, and general instrumentation. High-frequency PNP input transistors are used to obtain low input-voltage noise, while the bipolar process supports operation from single-supply rails beginning at 5 V. The package is a 14-pin PDIP with a 7.62 mm pin pitch. Its four-amplifier architecture provides a practical way to implement stereo or multichannel signal paths without using four separate packages. When configured with non-inverting gain, the bandwidth depends on the selected feedback components; higher closed-loop gain reduces usable bandwidth. The 7 V/µs slew rate also influences large-signal behavior, so square-wave and high-fidelity audio tests should be evaluated against the intended load and feedback network rather than bandwidth alone. Typical uses include microphone preamplification, audio mixer stages, active equalization, sensor conditioning, low-frequency active filters, and general-purpose instrumentation. The general-purpose designation indicates that the device is not limited to one application topology. It is especially relevant where several low-noise amplification channels are needed with a shared supply and a conventional through-hole package. For PCB implementation, maintain short feedback paths and place compensation or filtering components close to the relevant input and output pins. The ±18 V maximum supply rating must include tolerance, transient overshoot, and any rail-to-rail total. Decouple the supply near pin 8 with a short ground return to reduce supply-noise coupling into the four amplifier channels. This product page combines the manufacturer’s device description with package, electrical, application, lifecycle, and replacement guidance. It also emphasizes the practical distinctions between the MC33079PG and commonly discussed alternatives so that engineers can determine whether the 14-pin PDIP footprint, bipolar input stage, supply range, and 16 MHz bandwidth meet the design requirements before committing to a layout.

RFC Hubungi kami
MC33102P - Dual 100nA 1.7V/us Operational Amplifier | Onsemi
MC33102P

MC33102P - Dual 100nA 1.7V/us Operational Amplifier | Onsemi

The onsemi MC33102P is a dual operational amplifier with a two-state Sleep-Mode architecture, combining two amplifier channels in an 8-pin PDIP package. It is designed for low-power signal conditioning where the amplifier can remain in a low-power sleep state while waiting for an input signal and switch to an awake state when amplification is required. The device is specified as a micropower operational amplifier with 100 nA supply current, 1.7 V/us slew rate, and 4.6 MHz gain-bandwidth product. An operational amplifier is an active analog signal-conditioning component that uses high-gain differential amplification to increase the voltage level of a weak or small signal. A dual operational amplifier contains two amplifier sections in one package, allowing two related signals to be processed simultaneously while reducing board area. The MC33102P adds Sleep-Mode technology to this familiar amplifier function, making it useful in portable instruments, sensor interfaces, battery-powered systems, and other applications where standby consumption matters. The MC33102P's main features include dual general-purpose amplifier channels, a sleep-mode operating state, an awake-mode operating state, 100 nA supply current, 1.7 V/us slew rate, and 4.6 MHz gain-bandwidth product. The low supply current supports designs that spend significant time monitoring or waiting for a valid input. The sleep and awake states provide a mechanism to control when the amplifier is intended to respond to signal activity. The dual configuration allows the part to handle two amplifier functions in one package, such as signal conditioning for two sensor channels, an instrumentation front end, or gain stages around a comparator and data-conversion system. The 4.6 MHz gain-bandwidth product supports moderate-bandwidth applications, while the 1.7 V/us slew rate provides useful response for slowly varying and low-to-moderate-frequency analog signals. Its PDIP-8 package is suitable for conventional through-hole PCB assembly and prototyping. When designing around the MC33102P, check the input common-mode range, output swing, supply-voltage limits, stability requirements, and the meaning of the sleep-mode control behavior in the manufacturer datasheet. Place the device close to the signal source when handling high-impedance nodes, provide normal bypassing at the supply pins, and account for input bias-current errors and offset voltage when resolving low-level signals. This product page combines the MC33102P device identity, package information, operating characteristics, sourcing guidance, comparison framework, and practical design notes. The information is intended to help engineers confirm pin compatibility, assess the dual low-power amplifier architecture, and select a suitable replacement or design approach without treating a different package or electrical function as a drop-in substitute.

RFC Hubungi kami
MC33121P - Low-Voltage SLIC Interface | Motorola | PBX
MC33121P

MC33121P - Low-Voltage SLIC Interface | Motorola | PBX

The Motorola MC33121P is a low-voltage Subscriber Line Interface Circuit (SLIC) designed to connect the four-wire side of a central office or PBX to a two-wire subscriber line in a 14-pin plastic DIP package. It provides battery feed, loop-termination AC impedance, hookswitch detection, adjustable transmit, receive, and transhybrid gains, and single or double fault indication. The verified MC33121P listing identifies a 14-PDIP package, while the available technical material specifies a minimum longitudinal balance of 58 dB. A Subscriber Line Interface Circuit, or SLIC, is an integrated telecommunications interface that replaces many discrete functions associated with a analog telephone line. In the broader hierarchy, it is a specialized line interface IC within interface ICs and telecommunications semiconductors. It bridges a central-office or PBX voice path and a subscriber loop while separating transmit and receive signals, supporting line termination, and exposing hookswitch and fault information to the surrounding codec or control electronics. The MC33121P integrates several line-facing functions into one device. Battery feed supplies the line, while proper loop termination establishes the intended AC impedance seen by the subscriber. Adjustable transmit, receive, and transhybrid gains allow the surrounding system to control voice-path levels and balance. Hookswitch detection reports line activity, and separate status outputs indicate single or double faults, reducing the number of external discrete monitoring elements. Transmit and receive signals are referenced to analog ground, while digital status and control signals are referenced to digital ground. This separation simplifies interconnection with codecs, filters, and digital control logic. The hookswitch and fault outputs are compatible with TTL/CMOS, and the power-down input permits local shutdown. These interface features make the MC33121P suitable for integrated access, subscriber-line, PBX, voice codec, and central-office interface designs. Typical uses include a PBX line card, a central-office subscriber interface, a two-wire telephone-line interface, a voice codec interface, a hookswitch monitor, and a line-fault indication circuit. In each case, the IC provides the physical subscriber-line interface while external circuitry handles codec conversion, call control, supervision, and system-level power management. Because this legacy device is a through-hole 14-pin DIP, it is most practical for legacy designs, repair assemblies, and industrial or telecommunications equipment that can accommodate through-hole leaded components. Designers should preserve separate analog and digital grounding paths and connect the device to the selected codec, filter, and line-conditioning network exactly as shown in the manufacturer application material. Before production use, verify the unavailable operating voltage, temperature range, loop-current limits, external-component values, and absolute maximum ratings against the manufacturer datasheet. Those parameters are not supplied in the verified excerpts and therefore cannot be safely inferred. This page consolidates verified distributor pricing, package information, interface functions, comparison fields, and practical implementation cautions. It also distinguishes documented MC33121P characteristics from unverified alternatives, avoiding unsupported claims that a different SLIC is truly pin-to-pin compatible.

RFC Hubungi kami
MC33171D - 1.8MHz Low Power Single Op-Amp SOIC-8 | STMicroelectronics
MC33171D

MC33171D - 1.8MHz Low Power Single Op-Amp SOIC-8 | STMicroelectronics

The STMicroelectronics MC33171D is a low-power single bipolar operational amplifier fabricated with quality bipolar processing and innovative design concepts, housed in an 8-pin SOIC package. It operates at 180 uA per amplifier, delivers a 1.8 MHz gain bandwidth product and a 2.1 V/us slew rate, and supports supply operation from 3 V to 44 V single-supply (or split supplies). An operational amplifier (op-amp) is an analog building block within the broader hierarchy of amplifier ICs and linear semiconductors. It amplifies the voltage difference between its inverting and non-inverting inputs with high open-loop gain, and its behavior in a circuit is set almost entirely by external feedback components. General-purpose op-amps such as the MC33171 series sit at the entry level of this taxonomy, below precision, high-speed, and instrumentation amplifier families, yet they remain the workhorse of analog signal conditioning. Key features of the MC33171 include its exceptionally low 180 uA supply current per amplifier, which makes it attractive for battery-powered and energy-conscious designs. The bipolar fabrication (without JFET device technology) gives robust input behavior and predictable industry-standard single-op-amp pinout. The wide 3 V to 44 V supply range allows operation from single low-voltage rails or from higher industrial buses, and the device is particularly suited for single-supply operation although it can run from split supplies. Technically, the MC33171/72/74 monolithic series combines the low static current with usable AC performance: the 1.8 MHz bandwidth covers audio and low-frequency instrumentation needs, while the 2.1 V/us slew rate supports moderate-amplitude signal swings without excessive distortion at those frequencies. Typical applications include battery-powered portable instruments, sensor signal conditioning, active filters, transducer amplifiers, and low-frequency comparators or level shifters in industrial control, where low quiescent drain and wide supply tolerance matter more than ultra-high speed. A key design consideration: because it is optimized for low power rather than high speed, allow adequate settling margin in feedback networks and avoid pushing large output swings near the 1.8 MHz bandwidth limit to prevent slew-induced distortion. This page adds value beyond the manufacturer datasheet by consolidating cross-brand availability context, drop-in alternative guidance, practical design notes, and sourcing access through the Request a Quote form.

RFC Hubungi kami
MC33171DT - 2.1MHz Low-Power Op Amp | STMicroelectronics
MC33171DT

MC33171DT - 2.1MHz Low-Power Op Amp | STMicroelectronics

STMicroelectronics MC33171DT is a single bipolar operational amplifier optimized for low consumption and moderate speed, delivering a 2.1 MHz gain-bandwidth product with a 2 V/µs slew rate. It operates from a single 4 V to 44 V supply or from dual ±2 V to ±22 V rails and consumes approximately 200 µA. The amplifier is packaged in an 8-pin SOIC, making it suitable for industrial control, instrumentation, signal conditioning, and general-purpose analog signal paths. An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages. Within the broader hierarchy of analog and mixed-signal electronics, an operational amplifier belongs to the amplifier IC family and supports precision control, buffering, filtering, sensing, and feedback-based circuit functions. The MC33171 combines a bipolar input and output stage with a low-current architecture intended to preserve useful speed without the higher consumption associated with many general-purpose precision amplifiers. The MC33171DT's 2.1 MHz gain-bandwidth product supports signal paths where moderate bandwidth is more important than nanovolt-level input noise. Its 2 V/µs slew rate gives it the capability to process larger voltage changes quickly, while its approximately 200 µA consumption supports low-power signal-conditioning systems. The common-mode input range extends toward the lower supply rail, enabling single-supply operation from 4 V to 44 V. Dual-rail operation is also possible over a stated range of ±2 V to ±22 V. The 8-pin SOIC package provides a conventional surface-mount footprint for analog boards and simplifies assembly alongside mixed-signal components. Because this is a single-amplifier device, systems requiring multiple independent amplifier channels must use additional packages or a suitable multi-amplifier device. Designers should account for the operating voltage, common-mode range, output swing, stability with the selected feedback network, and external compensation requirements when designing a new circuit. Typical applications include industrial process-control loops, low-power sensor interfaces, audio and communication signal conditioning, active filters, and general-purpose amplification stages. The extended supply capability is useful in industrial systems where signal levels may vary widely. The low 200 µA consumption is particularly relevant when the amplifier operates continuously from a compact or space-constrained power budget. For reliable implementation, connect the supply pins to bypass capacitors and route feedback components to minimize parasitic effects. Maintain signal levels within the common-mode and output ranges, and verify stability with the actual load capacitance and source impedance. This page combines manufacturer specifications, package information, sourcing guidance, and practical design considerations for engineers evaluating the MC33171DT. For design trade-offs, compare the MC33171DT with the related MC33172DT and MC33174DT family members before fixing the BOM. Each option should be selected according to the required gain, bandwidth, slew behavior, and application circuit rather than package availability alone.

RFC Hubungi kami
MC33171N - 2.1MHz Low-Power Op Amp | STMicroelectronics
MC33171N

MC33171N - 2.1MHz Low-Power Op Amp | STMicroelectronics

STMicroelectronics MC33171N is a single bipolar operational amplifier with a 2.1 MHz gain-bandwidth product, 2 V/us slew rate, 200 uA supply current, and a DIP-8 package. It supports single-supply operation from 4 V to 44 V, while its input common-mode range extends to the lower supply rail. These characteristics make the MC33171N suitable for low-power analog signal conditioning, industrial instrumentation, sensor interfaces, and general-purpose voltage amplification. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify differences between two input voltages. The bipolar MC33171N belongs to the operational-amplifier, analog-IC, and semiconductor hierarchy. Its rail-to-rail input common-mode capability is particularly useful in single-supply systems because the input signal can approach the lower supply rail without requiring a negative power source. The principal features are a 2.1 MHz gain-bandwidth product, a 2 V/us slew rate, and a typical supply current of 200 uA. The 2.1 MHz bandwidth provides useful bandwidth for general-purpose analog stages, while the 2 V/us slew rate limits how quickly the output can follow large voltage changes. Low 200 uA consumption supports battery-powered and distributed instrumentation designs where amplifier power can dominate the system budget. The MC33171N uses a single bipolar amplifier architecture rather than a JFET-input implementation. This architecture combines low supply consumption with moderate operating speed and makes the device appropriate for continuous analog signal processing without the static bias current associated with higher-performance precision amplifiers. Its 4 V to 44 V single-supply range allows operation from conventional 5 V and 12 V rails as well as higher industrial supply voltages. Typical applications include low-frequency instrumentation amplifiers, current-sensor signal conditioning, buffered sensor outputs, industrial control inputs, and low-power analog measurement systems. The input common-mode range extending to the lower rail is valuable in systems powered from a single positive supply, where input signals can be close to ground. Gain and bandwidth should be selected together so that the closed-loop noise gain remains compatible with the 2.1 MHz gain-bandwidth product. A key design consideration is the relationship between supply voltage, output swing, and input range. Confirm that the required signal and output remain inside the operating limits before assigning a high closed-loop gain. Keep feedback routing short, place input and supply bypass capacitors close to their relevant pins, and avoid extending high-impedance input traces where leakage and interference can degrade accuracy. This product page combines the STMicroelectronics MC33171 operating characteristics with package guidance, pin assignments, application analysis, verified drop-in alternatives, and practical circuit-design notes. It is intended to help engineers select the amplifier, confirm footprint compatibility, and plan an efficient single-supply analog implementation.

RFC Hubungi kami
MC33171P - 3-44V Low-Power Op Amp | onsemi | 8-PDIP
MC33171P

MC33171P - 3-44V Low-Power Op Amp | onsemi | 8-PDIP

onsemi MC33171P is a single, general-purpose operational amplifier with a 3.0 V to 44 V supply range, low 180 uA operating current per amplifier, 1.8 MHz gain-bandwidth product, and 2.1 V/us slew rate. The device is packaged in an 8-pin plastic dual in-line package (8-PDIP). Its bipolar input stage provides a practical alternative to JFET-input amplifiers in applications that do not require JFET characteristics. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The MC33171 belongs to the operational-amplifier hierarchy within analog and mixed-signal semiconductors. It can operate from a single supply or split supplies, allowing it to serve as a general-purpose amplifier, buffer, comparator, or active-filter building block in industrial, instrumentation, and control circuits. Key characteristics include the wide 3.0 V to 44 V operating range, 180 uA current consumption per amplifier, 1.8 MHz gain-bandwidth product, and 2.1 V/us slew rate. These values position the device for low-power, moderate-bandwidth signal conditioning where a larger package is acceptable and through-hole assembly is preferred. The 8-PDIP format also simplifies prototyping, breadboarding, repair, and manual production processes. The bipolar fabrication approach provides the stated bandwidth and slew-rate performance without JFET-device technology. Because the operating supply extends to 44 V, the amplifier can accommodate higher-voltage systems than conventional low-voltage operational amplifiers. Designers must still verify input and output common-mode limits against the selected supply configuration before using the amplifier outside its intended operating region. Typical uses include low-frequency sensor conditioning, buffered transducer interfaces, audio preamplification, industrial control signals, power-supply feedback monitoring, and active analog filters. The 1.8 MHz gain-bandwidth product is suitable for many audio and instrumentation stages, while the 2.1 V/us slew rate supports reasonably clean responses to moderate-amplitude step inputs. When designing a board around the MC33171P, maintain adequate input and output voltage headroom, bypass the supply pins close to the device, and route high-impedance input signals with minimal leakage and contamination. Stable operation also depends on the feedback network, source impedance, output loading, and application-specific settling requirements. This product page combines the manufacturer's MC33171 family documentation, distributor package information, search-focused technical data, and practical design guidance. It also distinguishes verified drop-in alternatives from broader equivalents that may require different packages, supply ranges, or performance checks before substitution.

RFC Hubungi kami
MC33171PG - 1.8 MHz Low-Power Op Amp | onsemi | 8-DIP
MC33171PG

MC33171PG - 1.8 MHz Low-Power Op Amp | onsemi | 8-DIP

The onsemi MC33171PG is a single general-purpose operational amplifier in an 8-pin plastic DIP package, specified for single-supply operation from 3.0 V to 44 V. It combines a 1.8 MHz gain-bandwidth product with a 2.1 V/us slew rate and a low quiescent current of 180 uA per amplifier. The device is designed for low-power instrumentation, industrial signal conditioning, sensor amplification, and control applications requiring operation from a single supply. An operational amplifier, or op amp, is an analog signal-conditioning integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. Its hierarchy extends from general-purpose amplification to signal conditioning, analog mixed-signal ICs, and broader power-management-aware system design. The MC33171/72/74 family uses bipolar fabrication without JFET input transistors, combining low supply current with adequate bandwidth and slew rate for many industrial signal paths. Key electrical characteristics include a 1.8 MHz gain-bandwidth product, 2.1 V/us slew rate, and approximately 180 uA operating current per amplifier. The wide 3.0 V to 44 V single-supply range allows operation from conventional 5 V, 12 V, 24 V, and higher industrial rails. The MC33171PG is specified across a -40C to +85C temperature range, while its input bias current is listed at 20 nA and input offset voltage at 2 mV. The MC33171 series is particularly suited to single-supply operation but can also be used with split supplies when the circuit and common-mode conditions permit. Its bipolar input stage avoids the need for JFET technology, and the 1.8 MHz bandwidth supports audio-frequency and general instrumentation tasks. The 2.1 V/us slew rate improves large-signal response compared with strictly low-bandwidth precision amplifiers, although the device remains a general-purpose rather than a high-speed amplifier. Typical applications include low-frequency sensor conditioning, transducer amplification, process-control loops, industrial current or voltage monitoring, audio preamplification, and general-purpose analog filtering. For higher-impedance sensors, the 20 nA input bias specification helps minimize loading, while the 2 mV input offset must be considered in precision measurement paths. Feedback-network layout, grounding, and supply bypassing remain important at the board level. When designing around the MC33171PG, check input and output voltage swing at the intended load because single-supply operation restricts the usable signal range near the rails. Place bypass capacitors close to the supply pins, route feedback paths away from high-current inputs, and verify stability with the selected gain, load capacitance, and compensation network. For an obsolete legacy design, confirm availability before committing to new production layouts. This page combines lifecycle status, package details, verified electrical characteristics, replacement guidance, and board-level design notes for engineers maintaining MC33171PG-based instrumentation. It also compares same-footprint amplifier options and highlights the trade-offs among supply current, bandwidth, input offset, and operating-temperature range.

RFC Hubungi kami
MC33172D - Low-Power Dual Op Amp | STMicroelectronics
MC33172D

MC33172D - Low-Power Dual Op Amp | STMicroelectronics

The STMicroelectronics MC33172D is a low-power dual bipolar operational amplifier with two amplifier circuits, a gain-bandwidth product of 1.8 MHz, and an 8-pin SOIC package. It is designed for general-purpose signal conditioning applications where two independent amplifiers are useful in a single package. An operational amplifier is a voltage-controlled differential amplifier that compares two input voltages and amplifies their difference. Operational amplifiers form part of the broader analog IC and active-signal-processing hierarchy. The MC33172D uses bipolar transistor input stages and is suitable for functions such as buffering, gain amplification, comparisons, filtering, and instrumentation interfaces when configured with suitable external resistors and capacitors. Each MC33172D channel provides a practical combination of low power consumption and general-purpose signal handling. The device contains two amplifier circuits in one 8-SOIC package, reducing component count and board area in designs requiring paired amplification. Its listed maximum input offset voltage is 6.5 mV, while its unity-gain bandwidth is 1.8 MHz. These characteristics suit signal paths that do not require the very low offset, very high bandwidth, or very low noise associated with specialized precision amplifiers. The bipolar architecture is appropriate for low-frequency control, measurement, and conditioning circuits where the amplifier operates mainly in a closed-loop configuration. Noise, offset, input common-mode range, output swing, supply current, and stability characteristics must be checked against the actual signal amplitude and frequency before the device is used. Negative feedback, adequate output loading, and input-referenced compensation should follow the manufacturer's recommended application circuits. Typical applications include dual-axis sensor signal conditioning, active filtering, audio preamplification, threshold detection, low-frequency instrumentation, and general industrial control. Two channels can also implement differential or complementary signal processing when their inputs and outputs are configured appropriately. The 8-SOIC package is easy to assemble with conventional surface-mount production equipment and can simplify upgrades compared with discrete single-amplifier packages. Designers should verify the supported supply voltage, common-mode input range, output swing, input bias current, and operating temperature against the manufacturer's datasheet. Input and output voltages must remain within the electrical limits, and unused amplifier inputs should be biased rather than left floating. Stable feedback-network values are essential at higher frequencies. This product page combines package details, searchable technical questions, application guidance, and a drop-in comparison focused on practical amplifier selection. It helps engineers distinguish the dual bipolar MC33172D from higher-speed rail-to-rail alternatives before committing a circuit board to an 8-SOIC footprint.

RFC Hubungi kami
MC33172N - Dual 44V Low-Power Op Amp | STMicroelectronics
MC33172N

MC33172N - Dual 44V Low-Power Op Amp | STMicroelectronics

The STMicroelectronics MC33172N is a dual bipolar operational amplifier designed for low-power signal conditioning from single or dual supplies. It provides two amplifiers in an 8-pin PDIP package, operates from +4 V to +44 V, or equivalently from ±2 V to ±22 V, and is specified for approximately 200 µA per amplifier. The device offers 2.1 MHz gain-bandwidth product and a 2 V/µs slew rate for a practical balance of speed, power consumption, and operating range. An operational amplifier is an analog signal-processing IC that amplifies the voltage difference between its two inputs while using feedback to control gain, bandwidth, and output behavior. The dual-amplifier configuration places two independent amplifiers in one package, reducing board area in audio, instrumentation, industrial control, and sensor-interface circuits. MC33172N belongs to the bipolar operational-amplifier family within the broader voltage-regulator-free analog IC and semiconductor hierarchy. The headline electrical characteristics are its dual-amplifier architecture, 2.1 MHz gain-bandwidth product, 2 V/µs slew rate, and low supply current of approximately 200 µA per amplifier. These specifications make the device suitable for signals that require more bandwidth than a micropower-only amplifier but do not demand the very high speed or rail-to-rail performance of newer CMOS families. Its wide supply range also allows operation from conventional ±15 V and ±22 V analog rails. The MC3x172 series uses a bipolar input and output architecture rather than JFET input. This family construction supports operation from very low positive supplies through relatively high industrial voltage rails. Because the amplifiers are specified for both single- and dual-supply operation, the same device can be used in grounded single-supply designs, where the signal is biased around the midpoint of the supply, or in conventional dual-rail systems. Typical applications include low-frequency audio amplification, instrumentation-amplifier input stages, industrial sensor buffers, general-purpose signal conditioning, and power-supply feedback or monitoring circuits. The 8-pin PDIP package is mechanically straightforward for through-hole assembly and prototype work. The relatively low 200 µA-per-amplifier supply current is particularly useful when each active channel must remain powered continuously within a multi-channel measurement system. The principal design consideration is common-mode and output-range behavior. Designers should calculate signal swing, input bias requirements, and the effect of load current before fixing external resistor values. Because this is a bipolar amplifier rather than a rail-to-rail CMOS amplifier, input and output headroom must be checked against the selected supply voltage. Stable operation also depends on correct feedback topology and suitable output-load isolation. This product page combines the manufacturer datasheet with practical guidance for supply selection, signal conditioning, PCB implementation, and replacement assessment. It also distinguishes true pin-and-footprint-compatible options from broader functional equivalents so engineers can make a replacement decision without treating a similar amplifier as an automatic drop-in substitute.

RFC Hubungi kami
MC33172PG - Dual 44V Low-Power Op Amp | onsemi
MC33172PG

MC33172PG - Dual 44V Low-Power Op Amp | onsemi

The onsemi MC33172PG is a dual, low-power bipolar operational amplifier designed for general-purpose instrumentation and signal-conditioning applications. It operates from a single supply of 3.0 V to 44 V, provides two amplifiers in an 8-pin PDIP package, and supports both single-supply and split-supply operation. Its key characteristics include a 1.8 MHz gain-bandwidth product, a 2.1 V/µs slew rate, and approximately 180 mA of operating current per amplifier. An operational amplifier, or op amp, is a high-gain analog building block used to amplify voltage differences. The MC33172 belongs to the operational-amplifier hierarchy within analog signal-conditioning ICs. Its bipolar input stage uses conventional bipolar transistor technology rather than JFET devices, combining relatively low input-offset behavior with moderate bandwidth. The dual configuration permits two independent amplifier channels in one package, reducing board area when paired gain, filtering, or buffering functions are required. The MC33172PG is particularly suited to single-supply systems because its 3.0 V minimum supply voltage allows operation from regulated 3.3 V or 5 V rails. Split supplies are also supported when the circuit requires a bipolar signal range around ground. The 44 V maximum supply voltage provides additional headroom for higher-voltage industrial interfaces, although input and output common-mode limits must still be respected. Both channels are intended for low-power operation at approximately 180 mA per amplifier. With a gain-bandwidth product of 1.8 MHz and slew rate of 2.1 V/µs, the device is suitable for moderate-frequency precision rather than high-speed video or RF amplification. The 1.8 MHz gain-bandwidth product allows useful closed-loop bandwidth in lower-gain configurations, while the 2.1 V/µs slew rate limits large-signal response in wideband designs. These characteristics make signal rise times and stability more important than raw bandwidth in most applications. Typical uses include industrial sensor conditioning, current-loop receivers, low-frequency active filters, audio preamplification, transducer interfaces, and general-purpose buffer stages. It is especially useful when two channels can share the same supply and ground arrangement. Because the package is an 8-pin PDIP, the device is also convenient for through-hole prototyping and repair assemblies where a surface-mount footprint would be inconvenient. Design the input network, output loading, and supply decoupling around the ratings in the onsemi MC33172 datasheet. Place bypass capacitors close to the supply pins, observe the input common-mode range, and avoid driving capacitive loads unless stability compensation is provided. Confirm the exact pin assignments and operating limits against the manufacturer pin-description table before finalizing a PCB layout. This product page combines the manufacturer specifications, commercial guidance, same-package replacement analysis, and application-oriented design considerations. It supports faster part selection while keeping the decisive checks—supply range, amplifier bandwidth, package, pin compatibility, and common-mode limits—visible at the design stage.

RFC Hubungi kami
MC33174D - Low-Power Quad Bipolar Op Amp | STMicroelectronics
MC33174D

MC33174D - Low-Power Quad Bipolar Op Amp | STMicroelectronics

STMicroelectronics MC33174D is a low-power quad bipolar operational amplifier with 200 uA supply current per amplifier, 2.1 MHz gain-bandwidth product, and 2 V/us slew rate. The device is offered in a 14-pin SOIC package and supports single-supply operation from +4 V to +44 V. Its input common-mode range extends to the lower supply rail, making it useful in low-side sensing and single-supply signal chains. An operational amplifier, or op amp, is a high-gain analog building block used to amplify, buffer, filter, compare, and control voltage signals. MC33174D belongs to the broader amplifier IC, analog IC, and semiconductor hierarchies. Unlike an amplifier built around JFET input devices, this bipolar implementation combines low supply consumption with useful low-frequency bandwidth and slew performance for general-purpose analog signal conditioning. The four amplifiers provide flexible circuit partitioning for industrial instrumentation, sensor interfaces, active filters, and control loops. Key characteristics include 200 uA supply current per amplifier, 2.1 MHz gain-bandwidth product, and 2 V/us slew rate. The input common-mode range reaches the lower supply rail, which simplifies designs powered from a single positive rail while the signal approaches the lower operating limit. Operation from +4 V to +44 V gives the device broad supply-voltage flexibility. The 14-pin SOIC package supports conventional surface-mount assembly, while the quad channel count consolidates four amplifiers into one component. The manufacturer datasheet identifies the MC3x174 family as low-power bipolar operational amplifiers that combine low consumption with improved speed compared with basic general-purpose bipolar alternatives. Typical uses include low-side current sensing, buffered sensor outputs, precision signal conditioning, sample-and-hold circuits, active filters, and low-frequency control loops. The extended lower-rail common-mode capability is particularly valuable when a measurement begins near ground and the circuit has only one positive supply. Split-supply operation remains possible where bipolar signals or output swing are required. Designers should verify input and output voltage limits, common-mode range, output-load capability, and stability requirements against the manufacturer datasheet for the operating condition. Decoupling capacitors should be placed close to the supply pins, and each amplifier stage should be checked for output saturation during startup and overload transients. This page organizes the MC33174D specifications, package information, verified sourcing context, drop-in alternatives, comparison parameters, and application guidance into one engineering-focused reference. It also identifies the limits of the available cross-reference information so replacement decisions can be made without treating merely similar amplifier families as confirmed drop-in devices.

RFC Hubungi kami
MC33174DG - 3-44V Quad Low-Power Op Amp | onsemi
MC33174DG

MC33174DG - 3-44V Quad Low-Power Op Amp | onsemi

The onsemi MC33174DG is a four-channel, low-power operational amplifier built with bipolar fabrication technology, with a 3 V to 44 V single-supply operating range, 1.8 MHz gain-bandwidth product, and 2.1 V/µs slew rate in a 14-pin SOIC package. The device provides four amplifiers in one package, reducing board area and simplifying four-signal conditioning, buffering, or filtering designs. An operational amplifier is an analog signal-conditioning semiconductor that amplifies the difference between two input voltages while providing high input impedance, low output impedance, and predictable closed-loop behavior. The MC33174 belongs to the operational-amplifier hierarchy within amplifier ICs and signal-conditioning electronics. It is particularly suited to single-supply operation, allowing a common-mode input range to approach the lower supply rail for many practical signal-chain applications. Key features include four amplifier channels, 1.8 MHz gain-bandwidth product, 2.1 V/µs slew rate, and operation from 3 V to 44 V. The bipolar process avoids the need for JFET input transistors, while the four-channel integration reduces the number of packages required for instrumentation and industrial control circuits. The 14-SOIC format also supports conventional surface-mount assembly and PCB layout practices. The MC33174 family is designed for instrumentation, buffer-amplifier, and general-purpose signal-conditioning applications. Its 1.8 MHz bandwidth supports moderate-frequency amplification, while the 2.1 V/µs slew rate allows relatively fast transitions through larger voltage swings. Because the device is primarily intended for single-supply systems, input and output biasing should be selected carefully when signals approach the ground rail. Typical uses include current-loop and voltage-loop signal conditioning, sensor amplification, active filtering, transducer interfaces, sample-and-hold stages, and industrial control modules. In a four-channel instrumentation design, the MC33174 can amplify four related sensor or feedback signals while sharing one supply and ground arrangement. Its industrial supply range also supports systems operating from 24 V rails, provided signal amplitudes remain within the amplifier's common-mode limits. A practical design consideration is to verify common-mode range, output swing, stability, and noise performance at the intended supply voltage. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured according to the manufacturer's recommended stable-input circuit rather than left floating. This page combines the MC33174's confirmed operating characteristics, pin-compatible family alternatives, parameter comparisons, and practical implementation guidance to support component selection, PCB reuse, and robust analog-circuit design.

RFC Hubungi kami
MC33174N - Low Power Quad Bipolar Op-Amp, 2.1MHz | STMicroelectronics
MC33174N

MC33174N - Low Power Quad Bipolar Op-Amp, 2.1MHz | STMicroelectronics

The STMicroelectronics MC33174N is a quad bipolar operational amplifier in a 14-pin PDIP package, combining a low supply consumption of 200 uA per amplifier with a gain-bandwidth product of 2.1 MHz and a slew rate of 2 V/uS, while operating from a single +4 V to +44 V rail. The input common-mode range extends down to the lower supply rail, which allows the four amplifiers to be used directly in single-supply systems where the signal sits near 0 V. An operational amplifier (op-amp) is a voltage-amplifier building block whose gain, bandwidth and accuracy are shaped by negative feedback around a high-gain differential input stage. The MC3x174 family is built with monolithic bipolar fabrication and provides four amplifiers in a single package, making it a member of the analog amplifier IC hierarchy: op-amp -> quad operational amplifier -> analog amplifier IC -> analog semiconductor. Because four amplifiers share one package, a quad device reduces board area, decoupling capacitor count and total part count compared with four discrete single amplifiers. Key features of the MC33174N include the 200 uA low-consumption bias current that suits battery-fed and low-leakage measurement systems, the 2.1 MHz gain-bandwidth product that supports audio-band and general instrumentation signal paths, and the 2 V/uS slew rate that limits large-signal distortion on fast transients. The wide +4 V to +44 V supply span covers industrial 24 V rails, telecom 48 V style environments and split-supply laboratory setups from a single part family, and the rail-to-rail-referenced input stage avoids the need for a mid-supply bias network. Technically, the MC33171/72/74 series uses quality bipolar fabrication with high open-loop gain and 2.1 V/uS slew rate without relying on JFET input devices, which keeps input bias current low and stable while preserving moderate input impedance. The monolithic quad arrangement also means a common die and a common bias network, so all four channels track closely in offset and bandwidth. Because the package is a through-hole PDIP-14 with generous lead spacing, the part is easy to prototype on perfboard and to socket in legacy industrial equipment where surface-mount footprints are impractical. Typical applications include low-power sensor signal conditioning on 24 V industrial loops, battery-powered portable instrumentation, active filters and audio input stages, and general-purpose amplification inside test and measurement equipment. The 44 V maximum supply also allows the part to sit directly behind a protected 24 V or 36 V field wiring with additional headroom for transients. When designing with the MC33174N, note that the amplifier is intended for single-supply operation from +4 V, and while the common-mode input range reaches the lower rail, the output swing and offset behavior near that rail still deserve checking against the signal range you need. Decouple the supply pins close to the package, keep feedback resistors in the same range so noise and offset match, and confirm the input common-mode window in your specific gain configuration before relying on signals close to ground. This page consolidates the manufacturer datasheet parameters, package and pinout detail, plus drop-in replacement candidates and practical design notes, so that you can qualify the MC33174N for a new design or an obsolescence-driven substitution without hunting through multiple documents.

RFC Hubungi kami
MC33174PG - 44V Quad Op Amp, 1.8MHz | onsemi
MC33174PG

MC33174PG - 44V Quad Op Amp, 1.8MHz | onsemi

The onsemi MC33174PG is a general-purpose quad operational amplifier with four amplifiers in a 14-pin plastic DIP package. Each channel supports a 3 V to 44 V single-supply operating range, while the device combines a 1.8 MHz gain-bandwidth product, 2.1 V/µs slew rate, and approximately 180 µA supply current per channel. These characteristics make it suitable for general-purpose signal conditioning where four independent amplifiers are needed on one PCB footprint. An operational amplifier is an active semiconductor device that compares two input voltages and drives its output to amplify the difference between them. A quad operational amplifier integrates four amplifiers into one package, reducing board area and simplifying multi-channel instrumentation, sensor, audio, and control designs. The MC33174 belongs to the broader operational-amplifier hierarchy, where it functions as a voltage-feedback amplifier and ultimately as a general-purpose analog signal-conditioning IC. The MC33174PG's major benefits include its wide 3 V to 44 V supply range, low 180 µA supply current per amplifier, and 1.8 MHz gain-bandwidth product. The 2.1 V/µs slew rate supports moderate-accuracy signal transitions without the operating characteristics of a high-speed precision amplifier. A 20 nA input-bias-current specification is particularly useful in sensor interfaces and bias-resistor networks, although the complete electrical limits should be checked against the required supply voltage and common-mode range. The device uses quality bipolar fabrication and provides four amplifiers in the MC33171/MC33172/MC33174 operating-amplifier family. Its electrical performance is intended for general-purpose applications rather than precision instrumentation. The 14-DIP package provides a conventional through-hole footprint with 7.62 mm row spacing, making it suitable for prototyping, industrial control equipment, legacy systems, and applications where a dual-inline package is easier to assemble or inspect. Typical uses include four-channel sensor conditioning, industrial current and voltage monitoring, audio preamplification, active filtering, relay and actuator drive, laboratory instrumentation, and embedded control boards. Because it accepts supply voltages as high as 44 V, the device can also operate in higher-voltage industrial circuits when the signal common-mode voltage, output swing, and input protection remain within the device limits. The main design consideration is the relationship among bandwidth, supply voltage, and output swing. A gain of 10 reduces the usable bandwidth to approximately 180 kHz, so higher closed-loop gains should not be selected when wider signal bandwidth is required. Decoupling capacitors should be placed close to the supply pins, unused amplifier channels should be configured in a stable non-inverting arrangement, and input and output paths should avoid excessive capacitive loading. This product record combines the manufacturer family information, package identification, electrical characteristics, lifecycle context, sourcing workflow, and practical guidance for evaluating the MC33174PG in a new quad-amplifier design. It also distinguishes the exact MC33174PG from package and ordering-code variations so engineers can confirm footprint compatibility before replacement.

RFC Hubungi kami
MC33178D - Low-Power Low-Noise Dual Op Amp | onsemi
MC33178D

MC33178D - Low-Power Low-Noise Dual Op Amp | onsemi

onsemi MC33178D is a low-power, low-noise dual operational amplifier designed for audio and data-signal processing applications. It is a monolithic bipolar amplifier using high-frequency PNP input transistors, an architecture selected to provide low input offset voltage, low noise, and low distortion. The device is offered in an 8-pin SOIC package and contains two amplifier circuits, allowing it to support common signal-conditioning tasks in compact analog designs. An operational amplifier is a voltage-amplifying component that uses negative feedback to create controlled gain, filtering, buffering, and signal-conditioning functions. The dual-amplifier configuration places two amplifiers in one package, reducing board area and simplifying designs that require two related channels. Within the broader semiconductor hierarchy, MC33178D belongs to the operational-amplifier family, which is part of the wider analog integrated-circuit and signal-processing categories. The MC33178/9 family combines bipolar transistor implementation with PNP input devices and an NPN output stage. This combination is particularly relevant to audio and general-purpose data processing because the input architecture is intended to reduce offset and distortion while maintaining a practical low-noise operating approach. Its dual-channel organization also makes the device applicable to small-signal amplification, filtering, buffering, and related analog front-end functions. The part can be used where two amplifier channels are needed at the same signal level or operating condition. Typical use cases include audio signal conditioning, low-level sensor amplification, active filtering, buffering, and general analog signal processing. The low-noise characteristic makes it relevant to designs in which the amplifier must preserve a small input signal without adding substantial unwanted noise, while the low-distortion architecture supports cleaner waveform reproduction. When designing around MC33178D, begin by confirming the required input common-mode range, output swing, gain-bandwidth behavior, input offset voltage, input bias current, and supply-current limits against the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins, and sensitive-input routing should avoid nearby switching nodes and high-current return paths. This page combines the manufacturer family information with package, sourcing, comparison, and design guidance to support initial component evaluation and PCB planning. MC33178D is therefore suited to engineers seeking a compact, dual-channel, low-power bipolar op amp for audio or data-signal processing. Its strongest differentiators are the combined low-noise and low-distortion architecture, dual amplifier integration, and 8-pin SOIC implementation. Confirm the exact electrical limits and environmental ratings for the finished design before release to production.

RFC Hubungi kami
MC33178PG - Dual Low-Power Low-Noise Op Amp | onsemi
MC33178PG

MC33178PG - Dual Low-Power Low-Noise Op Amp | onsemi

The onsemi MC33178PG is a dual, bipolar operational amplifier packaged in an 8-pin PDIP. It operates from 2 V to 18 V, is intended for low-power industrial signal-processing applications, and offers a gain-bandwidth product of 5 MHz. The device uses high-frequency PNP input transistors to provide low input offset voltage, low noise, and low distortion. An operational amplifier is a high-gain analog signal-conditioning component used in instrumentation, audio, and data-processing circuits. It compares an input signal with a feedback reference to amplify voltage differences. Within the broader semiconductor hierarchy, the MC33178PG belongs to the operational-amplifier, analog-amplifier, and signal-conditioning IC families. The MC33178 family combines two amplifiers in one package, reducing board area for dual-channel designs. Its bipolar construction supports low-noise analog signal handling, while the PNP input stage is intended to improve offset voltage and distortion performance. The manufacturer identifies the family for quality audio and data-signal-processing applications. The MC33178PG operates from 2 V to 18 V, making it suitable for low-voltage industrial systems as well as conventional dual-supply analog circuits. A typical dual op-amp layout uses pins 1 and 7 as outputs, pins 2 and 6 as inverting inputs, pins 3 and 5 as non-inverting inputs, and pins 4 and 8 as the negative and positive supplies. Typical applications include audio preamplification, low-level sensor conditioning, active filtering, instrumentation, and general-purpose analog signal processing. When operating from a single supply, the input and output signal levels must remain within the input common-mode range and output swing limits specified by the manufacturer datasheet. For stable operation, follow the datasheet requirements for bypassing the positive supply and configure feedback so that the required noise gain and closed-loop bandwidth remain compatible with the intended signal path. Avoid placing input and output traces beside unrelated high-current switching nodes to reduce coupling. This page combines the manufacturer's device description with application-oriented guidance, pin organization, package information, and a conservative replacement comparison. It also identifies which drop-in alternatives have documented package compatibility and where final electrical verification remains necessary before a substitution is approved.

RFC Hubungi kami