onsemi

MC33172PG - Dual 44V Low-Power Op Amp | onsemi

MPN: MC33172PG ✓ Aktif
3.0 V to 44 V Vdss Approximately 180 mA Id 8-pin PDIP Package
MOQ: 1 |

MC33172PG Ringkasan

The onsemi MC33172PG is a dual, low-power bipolar operational amplifier designed for general-purpose instrumentation and signal-conditioning applications. It operates from a single supply of 3.0 V to 44 V, provides two amplifiers in an 8-pin PDIP package, and supports both single-supply and split-supply operation. Its key characteristics include a 1.8 MHz gain-bandwidth product, a 2.1 V/µs slew rate, and approximately 180 mA of operating current per amplifier.

An operational amplifier, or op amp, is a high-gain analog building block used to amplify voltage differences. The MC33172 belongs to the operational-amplifier hierarchy within analog signal-conditioning ICs. Its bipolar input stage uses conventional bipolar transistor technology rather than JFET devices, combining relatively low input-offset behavior with moderate bandwidth. The dual configuration permits two independent amplifier channels in one package, reducing board area when paired gain, filtering, or buffering functions are required.

The MC33172PG is particularly suited to single-supply systems because its 3.0 V minimum supply voltage allows operation from regulated 3.3 V or 5 V rails. Split supplies are also supported when the circuit requires a bipolar signal range around ground. The 44 V maximum supply voltage provides additional headroom for higher-voltage industrial interfaces, although input and output common-mode limits must still be respected. Both channels are intended for low-power operation at approximately 180 mA per amplifier.

With a gain-bandwidth product of 1.8 MHz and slew rate of 2.1 V/µs, the device is suitable for moderate-frequency precision rather than high-speed video or RF amplification. The 1.8 MHz gain-bandwidth product allows useful closed-loop bandwidth in lower-gain configurations, while the 2.1 V/µs slew rate limits large-signal response in wideband designs. These characteristics make signal rise times and stability more important than raw bandwidth in most applications.

Typical uses include industrial sensor conditioning, current-loop receivers, low-frequency active filters, audio preamplification, transducer interfaces, and general-purpose buffer stages. It is especially useful when two channels can share the same supply and ground arrangement. Because the package is an 8-pin PDIP, the device is also convenient for through-hole prototyping and repair assemblies where a surface-mount footprint would be inconvenient.

Design the input network, output loading, and supply decoupling around the ratings in the onsemi MC33172 datasheet. Place bypass capacitors close to the supply pins, observe the input common-mode range, and avoid driving capacitive loads unless stability compensation is provided. Confirm the exact pin assignments and operating limits against the manufacturer pin-description table before finalizing a PCB layout.

This product page combines the manufacturer specifications, commercial guidance, same-package replacement analysis, and application-oriented design considerations. It supports faster part selection while keeping the decisive checks—supply range, amplifier bandwidth, package, pin compatibility, and common-mode limits—visible at the design stage.

Pilihan pengganti yang segera untuk MC33172PG — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

MC33172P

✅ Masuk Drop-In
📦 8-pin PDIP
Same dual MC33172 family and 8-pin PDIP package; ordering-suffix temperature, qualification, or packaging details must be compared before substitution.

📋 Alternatif rujukan (tidak dalam katalog)

MC33172PG Penilaian maksimum & Ciri-ciri Elektrik

Amplifier Count 2 amplifiers
Product Type Dual operational amplifier
Supply Voltage Range 3.0 V to 44 V
Gain-Bandwidth Product 1.8 MHz
Slew Rate 2.1 V/µs
Operating Current per Amplifier Approximately 180 mA
Input Transistor Technology Bipolar
Supply Configuration Single supply or split supply
Kemasan 8-pin PDIP
Jenis Pemasangan Through-hole
Temperature Grade Industrial temperature range
Automotive Temperature Version Available in the MC33171/72/74 series

Panduan Konfigurasi Pin MC33172PG 8-pin pdip

Konfigurasi pin untuk MC33172PG (8-pin pdip pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.

Garis bentuk pengecah pakai 8-pin pdip untuk MC33172PG

Tiada data garisan pin yang diperoleh untuk MC33172PG.

Rujuk kepada lembaran data untuk konfigurasi pin penuh.

Aplikasi Biasa

MC33172PG patut untuk 6 aplikasis: Industrial Sensor Signal Conditioning, Low-Frequency Active Filter, Current-Loop Receiver, Audio Preamplifier, Transducer Interface, Power Supply Feedback Buffer.

🏭

Industrial Sensor Signal Conditioning

The MC33172PG suits two-channel industrial sensor conditioning because it combines a 3.0 V minimum supply with approximately 180 mA operating current per amplifier. Place one channel around a sensor amplifier and use the second for filtering or an output buffer when the source impedance is high. The 1.8 MHz gain-bandwidth product supports moderate-gain stages, while the 2.1 V/µs slew rate handles sensor transients without operating as a high-speed amplifier. Protect inputs against excessive common-mode voltage and use local supply bypassing to prevent sensor excitation noise from coupling into the measurement chain.

🔧

Low-Frequency Active Filter

The MC33172PG can implement dual-section low-frequency active filters using its two amplifier channels. The 1.8 MHz gain-bandwidth product is suitable for filters whose operating frequencies remain well below the closed-loop bandwidth limit, and the bipolar input stage supports general-purpose precision-oriented designs. Keep the feedback network values consistent with the selected topology and account for the amplifier's slew rate when processing large low-frequency signals. Decoupling capacitors should be placed near the supply pins, while sensitive filter nodes should remain away from high-current return paths.

🏭

Current-Loop Receiver

The MC33172PG is appropriate for a 4-20 mA current-loop receiver when the application operates from a 5 V or higher supply and does not require modern micropower features. One channel can provide the main transimpedance or difference-amplifier function, while the other can add active filtering or a diagnostic buffer. Its 2.1 V/µs slew rate provides adequate response for many industrial process-control loops, but shunt-resistor values, common-mode limits, and input protection must be designed carefully. Verify loop bandwidth and transient behavior against the complete manufacturer electrical characteristics.

🎧

Audio Preamplifier

The MC33172PG can serve as a dual-channel audio preamplifier in equipment that prioritizes simplicity and supply flexibility over low-noise performance. Its bipolar input stage, 1.8 MHz gain-bandwidth product, and 2.1 V/µs slew rate are suitable for low- and mid-frequency audio paths. Use one amplifier per channel to preserve channel symmetry, and configure input and feedback networks for the intended source impedance. Check the input noise, offset voltage, and output-swing requirements in the onsemi datasheet because a general-purpose operational amplifier may not match a dedicated audio amplifier.

🧩

Transducer Interface

The MC33172PG is useful for bridge, resistive, or other transducer interfaces where two low-frequency amplifier stages are required. Its single-supply capability from 3.0 V simplifies systems that also use a 3.3 V embedded controller, and the second channel can provide excitation-buffer support, gain, or active filtering. The device's approximately 180 mA per-amplifier operating current must be included in the power budget. Input bias current, offset voltage, noise, and common-mode range are important when working with high-impedance sensors and should be checked against the final bridge impedance.

⚡

Power Supply Feedback Buffer

The MC33172PG can buffer a remote or high-impedance feedback node in a linear power-supply control loop, with the second channel used for error amplification or signal conditioning. The 3.0 V to 44 V operating range permits use across multiple regulated-rail domains, while the 1.8 MHz gain-bandwidth product can support many compensation networks that operate at substantially lower crossover frequencies. Verify the input and output ranges at the exact rail voltages, maintain adequate phase margin, and avoid capacitive loading on the buffered feedback node unless stability has been evaluated.

Ringkasan Produk Disebarkan

MC33172P Same-family dual operational amplifier Dipergunakan di: Industrial Sensor Signal Conditioning, Low-Frequency Active Filter, Current-Loop Receiver, Audio Preamplifier, Transducer Interface, Power Supply Feedback Buffer LM2902N/PB Texas Instruments Dipergunakan di: Industrial Sensor Signal Conditioning, Low-Frequency Active Filter, Current-Loop Receiver, Audio Preamplifier, Transducer Interface, Power Supply Feedback Buffer
What is the operating voltage of MC33172PG?
The MC33172PG operates from a 3.0 V to 44 V supply. According to the onsemi MC33172 datasheet, the device is particularly suited to single-supply operation while also supporting split supplies. This range permits use with common 3.3 V and 5 V regulated rails and provides headroom for higher-voltage industrial signal-conditioning systems. Input common-mode and output-swing restrictions remain narrower than the full supply rating, so each signal must remain inside the limits specified by the manufacturer.
What are the key specifications of MC33172PG that engineers should know?
The MC33172PG is a dual bipolar operational amplifier with a 3.0 V to 44 V supply range, 1.8 MHz gain-bandwidth product, and 2.1 V/µs slew rate. It provides two amplifier channels in an 8-pin PDIP package and operates at approximately 180 mA per amplifier. These figures place it in the low-power, general-purpose instrumentation class, making it appropriate for industrial sensor interfaces, low-frequency filters, buffering, and moderate-speed signal conditioning.
What can replace MC33172PG?
MC33172P is the closest identified same-package replacement because the MC33172 family uses an 8-pin PDIP and the listed MC33172P also appears as an 8-pin PDIP dual amplifier. Pin assignments and operating details must be checked in the onsemi datasheet before substitution. The cross-reference search did not establish five verified pin-to-pin alternatives, so functionally similar amplifiers in other packages should not be treated as direct replacements without an engineering review.
Is MC33172PG suitable for single 5 V supply operation?
Yes, the MC33172PG is suitable for 5 V single-supply operation because its documented supply range begins at 3.0 V and extends to 44 V. The onsemi family description specifically identifies single-supply operation as a strength. The input signal must remain within the specified common-mode range, and the output must retain adequate swing from each supply rail, so single-supply designs should include suitable biasing or level shifting when processing signals centered near ground.
MC33172PG vs MC33172P - which one should I select?
MC33172P is the listed 8-pin PDIP member of the same MC33172 family and is the closest verified alternative for MC33172PG. The manufacturer page identifies MC33172 as a family covering industrial and automotive temperature ranges with plastic and surface-mount options. Because the orderable suffix can encode temperature, quality, or packaging details, compare the full ordering information, pin table, temperature range, and qualification status before deciding which suffix fits the assembly.
When should I choose MC33172PG over another dual operational amplifier?
Choose MC33172PG when the design needs two amplifier channels, a through-hole 8-pin PDIP package, and a broad 3.0 V to 44 V supply range. Its 1.8 MHz gain-bandwidth product and 2.1 V/µs slew rate suit low-frequency instrumentation, filtering, buffering, and industrial signal conditioning. Choose another amplifier instead when the circuit requires substantially greater bandwidth, lower noise, rail-to-rail output, lower supply current, or a package already fixed by an existing PCB.
Where can I download the MC33172PG datasheet PDF?
The official MC33172 product page provides the authoritative MC33172 datasheet and ordering information. It covers the MC33171, MC33172, and MC33174 bipolar operational-amplifier family, including the dual MC33172 configuration used by MC33172PG. Use the onsemi product page as the primary document location and confirm the MC33172 ordering table for package, temperature, and qualification details. Third-party document archives can assist with discovery but should not replace the manufacturer document for design release.
Where is the MC33172PG pinout?
The MC33172PG pinout is published in the pin-description table of the onsemi MC33172 datasheet. Because MC33172PG is an 8-pin PDIP device, the drawing uses the standard counter-clockwise numbering of that package, beginning at pin 1 near the package marking. Use the manufacturer table when assigning input, output, supply, and ground connections. Do not infer the dual-amplifier pin functions from another package because changing from PDIP to a surface-mount option can change pin placement.
What is the best drop-in replacement for MC33172PG?
MC33172P is the best directly identified candidate because it belongs to the same MC33172 family and is listed in an 8-pin PDIP package. A true drop-in decision also requires matching pin functions, supply range, temperature grade, offset, bias current, common-mode range, and output capability. No additional cross-brand part was verified as both pin-to-pin compatible and available in the same PDIP package, so MC33172P is the only confirmed same-package candidate identified for the target.
How much bandwidth does MC33172PG have?
The MC33172PG has a gain-bandwidth product of 1.8 MHz and a slew rate of 2.1 V/µs. According to the onsemi MC33172 family description, these values are achieved with bipolar input devices without JFET technology. Closed-loop bandwidth depends on noise gain and stability, while the slew rate governs large-signal response. The device is therefore best suited to moderate-speed instrumentation rather than applications requiring high-frequency or high-amplitude waveform performance.
What is the power consumption of MC33172PG?
The MC33172 family operates at approximately 180 mA per amplifier, equivalent to roughly 360 mA total when both channels are active at comparable conditions. Actual dissipation depends on the supply voltage, operating state, output swing, and load. Estimated: with both amplifiers operating from 5 V at 180 mA per channel, the device dissipates approximately 1.8 W; confirm the maximum package dissipation and temperature-rise limits from the manufacturer datasheet.
Is MC33172PG in stock, and what is its lead time?
Current inventory and lead time should be requested through the Request a Quote form on this page. The manufacturer lists MC33172 as an active operational-amplifier family, while distributor listings may change stock by quantity and package suffix. For production planning, provide the exact MC33172PG ordering code, annual demand, and permitted alternatives. Do not substitute a different package or amplifier configuration merely to meet a target date without confirming electrical and pin compatibility.
What is the price of MC33172PG?
The current commercial quotation for MC33172PG should be requested through the Request a Quote form on this page. The structured price shown on the product page reflects the applicable sourcing mode and can change with quantity, availability, and packaging requirements. For an accurate quotation, state the required quantity, target delivery date, shipment country, and whether the 8-pin PDIP ordering configuration is mandatory.
Where can I buy MC33172PG online?
Use the Request a Quote form on this page to request MC33172PG from XAIPART. Include the desired quantity, delivery location, and required production schedule so the exact 8-pin PDIP configuration can be confirmed. The part is an onsemi dual operational amplifier in the MC33172 family and is listed as active on the manufacturer's product page. Quotation requests are the appropriate route when stock, volume, or lead-time confirmation is required.
Does MC33172PG support split-supply operation?
Yes, the MC33172PG supports both split-supply and single-supply operation. The onsemi family description states that the amplifiers can be operated from split supplies but are particularly suited to single-supply systems. In a split configuration, each rail must remain within the 3.0 V to 44 V total supply constraint, and the input and output voltages must satisfy the common-mode and output-swing restrictions for the particular supply arrangement.

Data referensi kejuruteraan untuk MC33172PG — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose MC33172PG for general-purpose dual amplification when the design uses a 3.3 V or 5 V supply, requires an 8-pin through-hole footprint, and operates at low-to-moderate signal frequencies. Its 1.8 MHz gain-bandwidth product and 2.1 V/µs slew rate make it appropriate for sensor conditioning, active filters, buffering, current-loop interfaces, and low-frequency audio paths. MC33172P is the closest same-package option because it uses the same dual MC33172 family and 8-pin PDIP format; compare its full ordering suffix, temperature grade, qualification status, and current electrical limits before replacement. Select a different amplifier when the design requires substantially lower noise, lower power consumption, rail-to-rail output, greater bandwidth, or a surface-mount footprint. Those changes affect circuit values, stability analysis, supply headroom, and PCB layout, so they should not be treated as simple drop-in substitutions.

Perbandingan dengan Gantian

Parametr Produk Ini MC33172P
Package 8-pin PDIP 8-pin PDIP
Brand onsemi onsemi
Amplifier Configuration Dual Dual
Supply Voltage Range 3.0 V to 44 V 3.0 V to 44 V
Gain-Bandwidth Product 1.8 MHz 1.8 MHz
Slew Rate 2.1 V/µs 2.1 V/µs
Operating Current per Amplifier Approximately 180 mA Approximately 180 mA
Input Technology Bipolar Bipolar
Supply Modes Single supply or split supply Single supply or split supply
Special Ordering Detail MC33172PG suffix MC33172P ordering suffix; temperature and qualification details require comparison

Penyeberangsung Jelas

  • Combines two channels with a broad supply range in one 8-pin PDIP package (vsMC33172P)
  • Moderate bandwidth and slew performance for low-power instrumentation (vsMC33172P)
  • Supports both 3.3 V and 5 V single-supply architectures (vsMC33172P)

Catatan Desain

Account for both channels when estimating the supply budget. Estimated: at a 5 V supply and approximately 180 mA per amplifier, the device can dissipate about 1.8 W with both outputs at their quiescent operating points. Actual dissipation changes with output voltage, load, and channel activity. Use the onsemi package dissipation and thermal information to determine whether the 8-pin PDIP requires a particular copper area or heat-spreading arrangement.

Route the two channels to minimize shared-impedance coupling between inputs, outputs, and ground returns. Place the supply bypass capacitor close to the positive and ground pins, and keep sensitive input traces away from power-supply switching nodes. In a dual-channel design, avoid routing one channel's output near the other channel's high-impedance input because parasitic coupling can create crosstalk or oscillation.

Do not treat the 3.0 V to 44 V supply rating as the usable input or output range. Common-mode voltage, output swing, and input-current limits are narrower and depend on the actual supply voltage. Confirm these boundaries in the manufacturer pin-description and electrical-characteristics tables. Also verify the complete MC33172 ordering suffix before substituting MC33172P, since temperature grade and qualification requirements may differ even though the package and principal family characteristics match.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

The onsemi product-page material identifies industrial and automotive-temperature versions within the MC33171/72/74 family, but it does not state the MC33172PG suffix's individual RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status.

Pencarian Berhubungan

MC33172PG datasheet MC33172PG pinout MC33172PG datasheet pdf onsemi MC33172PG MC33172PG equivalent MC33172PG replacement MC33172PG vs MC33172P MC33172PG 3.0V 44V MC33172PG 1.8MHz dual op amp MC33172PG PDIP application circuit MC33172PG price MC33172PG stock

Komponen dan Tanda berkaitan

onsemi MC33172PG MC33172P MC33171 MC33172 MC33174 TLV9302 LM2902N/PB dual operational amplifier operational amplifier op amp analog signal-conditioning IC bipolar input stage single-supply operation split-supply operation gain-bandwidth product slew rate input common-mode range output voltage swing 8-pin PDIP PDIP package through-hole mounting industrial instrumentation sensor conditioning active filter
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ