Pengurusan Kuasa
Subkategori
Produk (2,800+)
IRS25751LTRPBF - 480V High-Voltage Start-Up PMIC | Infineon
The Infineon IRS25751LTRPBF is a 480 V high-voltage start-up PMIC housed in a 5-pin SOT-23 surface-mount package that delivers a regulated 4.5 mA constant current to charge a bootstrap or auxiliary supply from a rectified high-voltage bus, then drops to ultra-low standby current once the downstream converter begins operation. It is qualified to drive the initial supply rail of IGBT- and MOSFET-based power converters directly from rectified mains up to 480 V without an auxiliary winding or low-voltage dropper, dramatically simplifying PFC, LLC, half-bridge, and flyback start-up circuits. A high-voltage start-up IC is a specialized power management device that provides a small, regulated bias current to a switching converter's controller during cold start-up when no auxiliary winding voltage is yet available. After the converter begins switching and its auxiliary rail comes up, the start-up IC turns off to achieve micro-amp standby current. This category sits within the broader PMIC (power management integrated circuit) family and bridges high-voltage rectification rails to low-voltage control logic - functionally complementary to but distinct from DC-DC converters, linear regulators, and gate drivers. Key features of the IRS25751L include programmable upper turn-off threshold, an active-low ENN enable input, integrated over-temperature protection, and Infineon's proprietary HVIC (high-voltage integrated circuit) technology rated for 480 V bus operation. The part uses Infineon's junction-isolation HVIC process that integrates a 480 V-capable JFET input with low-voltage CMOS control, eliminating external bleed resistors and high-voltage transistors. Designed for IGBT and MOSFET half-bridge driver supplies, the IRS25751L is most commonly used as the start-up source for PFC + LLC combo controllers, single-stage flyback converters, and industrial motor drives. The 4.5 mA constant-current behavior is sufficient to charge the VCC capacitor of typical driver ICs within a few hundred milliseconds. When designing with this device, ensure VCC is decoupled with at least 1 uF of low-ESR ceramic capacitance and verify the upper turn-off threshold matches the downstream controller's UVLO release point. The ENN pin allows synchronization with PFC_OK signals or sequential turn-on in multi-stage converters, while the over-temperature protection engages at approximately 145 C junction.
IRS4427STRPBF - 25V Dual Low-Side Gate Driver, 3.3A | Infineon
The Infineon IRS4427STRPBF is a 25V dual low-side gate driver IC designed to switch IGBTs and power MOSFETs, housed in an 8-pin SOIC (DSO-8) package. It delivers 2.3A source current and 3.3A sink current with 50ns typical propagation delay per channel, and operates from a 6V to 20V gate-drive supply. The two independent channels use CMOS Schmitt-triggered inputs that are 3.3V and 5V logic compatible, enabling direct connection to modern microcontrollers and DSPs without level shifters. A gate driver IC (also called a MOSFET driver or IGBT driver) is a power-management device that sits between a low-power logic controller and a high-power switching transistor. It multiplies the current and voltage capability of the logic signal so the controller can toggle the gate of a MOSFET or IGBT efficiently. Within the broader hierarchy, the IRS4427 belongs to: gate driver -> driver IC -> power management IC -> semiconductor. Low-side drivers like the IRS4427 reference the load to the positive rail, making them simpler and cheaper than half-bridge or high-side drivers when the switching node is ground-referenced. Key features include matched propagation delay between the two channels for synchronous switching, non-inverting logic (output in phase with input), under-voltage lockout protection, and 2.3A/3.3A peak source/sink capability. The IRS4427 is pin-compatible with the IRS4428S variant, which provides one inverting and one non-inverting channel; it is also pin-compatible with the legacy IR4427 (pre-Infineon part number from International Rectifier, which Infineon acquired in 2015). The architecture uses a CMOS input stage with Schmitt-trigger hysteresis for noise immunity, followed by a push-pull output stage capable of delivering fast gate transitions. The high sink current (3.3A) is particularly valuable for discharging MOSFET gate charges quickly, minimizing switching losses in high-frequency applications. Two independent channels allow driving two separate switches, such as the two low-side FETs in a synchronous buck converter. Typical applications include driving the low-side MOSFET in DC-DC converters, motor control H-bridges, solenoid drivers, Class-D audio amplifiers, and general power switching. The dual-channel configuration is well suited for synchronous rectification in switch-mode power supplies (SMPS). When designing with this driver, place a 1uF ceramic bypass capacitor close to VCC to handle the high di/dt of gate-charge transfer, and keep the gate-drive traces short to minimize parasitic inductance. The IRS4427 outputs are designed to drive MOSFET gates directly; no external buffer is needed for typical gate charges up to 50nC. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical design notes not found in the manufacturer datasheet alone, helping engineers source and apply the IRS4427STRPBF with confidence.
IRS4428STRPBF - 25V Dual Low-Side 3.3A Gate Driver | Infineon
The Infineon IRS4428STRPBF is a dual low-side gate driver IC delivering 3.3 A peak output current in an 8-pin SOIC package with tape-and-reel packaging. It operates from a 6 V to 20 V gate-drive supply range and supports input logic levels down to 3.3 V, making it directly compatible with modern microcontrollers and DSPs. Each of the two independent driver channels is CMOS Schmitt-triggered and provides matched propagation delay for tight timing alignment in half-bridge or synchronous-rectifier topologies. A low-side gate driver is an integrated circuit that buffers low-power logic signals (such as a PWM output from a microcontroller) into the higher-current, fast-switching waveforms required to charge and discharge the gate of a power MOSFET, IGBT, or GaN transistor sitting on the low (source/emitter) side of the switching node. Low-side drivers sit within the broader hierarchy of gate-driver ICs, which themselves belong to power-management semiconductors; they are essential whenever logic-level signals cannot directly drive a power switch fast enough or hard enough to minimize switching losses. Key features include 3.3 V and 5 V logic compatibility on the inputs, a typical 50 ns propagation delay, matched channel-to-channel delay for symmetric drive timing, an inverting/non-inverting input pair, and under-voltage lockout (UVLO) on the VCC rail. The outputs source/sink up to 2.3 A peak per channel per the digchip datasheet excerpt, with 3.3 A peak commonly quoted by Infineon marketing material for the IRS4428 family. The 8-SOIC surface-mount package provides a compact footprint for high-density power boards. Internally, the IRS4428S uses a CMOS push-pull output stage optimized for sub-100 ns transitions at the gate of standard power MOSFETs. The matched propagation delay between the two channels (typically within a few nanoseconds) ensures balanced drive timing, which is critical in synchronous rectifiers and dual-switch applications where timing mismatch translates directly into shoot-through risk or efficiency loss. Typical applications include half-bridge and full-bridge motor drives, synchronous-rectifier gate drive in DC-DC converters, high-frequency switch-mode power supplies (SMPS), Class-D audio amplifiers, and industrial low-side switching of IGBT/MOSFET loads. The wide 6 V to 20 V VCC range allows direct drive of standard N-channel MOSFETs from a 12 V bus without an auxiliary charge pump. When designing with this part, place the VCC bypass capacitor (typically 0.1 uF ceramic) as close as possible to pin 8, and ensure the logic inputs are tied to a defined state when not driven to prevent unintended switching. The matched delay specification simplifies timing analysis in dual-channel designs.
IRS9102CXTSA1 - 12A VCSEL/LED Laser Driver IC | Infineon
The Infineon IRS9102CXTSA1 is a 12 A laser diode / LED driver IC purpose-built for indirect Time-of-Flight (iToF) image sensors, packaged in the compact 10-lead PG-TSNP-10-4 surface-mount package. According to the Infineon product page, it delivers up to 12 A peak laser current with 250 MHz modulation bandwidth and integrated fail-safe protection, and it is designed to pair directly with Infineon's REAL3 iToF image sensor family while remaining usable in laser distance sensors (LDS) and LiDAR front-ends. A laser driver is a specialized power-management IC that converts a low-current logic signal into a precisely controlled high-current pulse that drives a laser diode or LED. Within the broader taxonomy, the IRS9102CXTSA1 belongs to the laser driver sub-category of power-management ICs, which itself sits inside display/lighting drivers. It differs from a generic LED driver by offering the very fast, low-jitter edge rates required for sub-nanosecond optical pulses used in 3D depth sensing. Key features include a wide supply voltage range of 2.52 V to 3.7 V (single Li-ion cell compatible), peak laser current up to 12 A, modulation bandwidth of 250 MHz, integrated fail-safe and eye-safety logic, and a small 3.0 mm × 3.0 mm PG-TSNP-10-4 footprint. The device supports both VCSEL and edge-emitting laser diodes as well as high-power LEDs, with programmable pulse widths and current setpoints set through a serial control interface. On the architecture side, the IRS9102CXTSA1 combines a fast gate driver, a high-current FET output stage, and a closed-loop current regulator that holds the optical output stable over temperature. The 250 MHz bandwidth allows sub-nanosecond pulse shaping required by emerging iToF depth sensors, while the fail-safe block monitors voltage, current, and temperature conditions and disables the laser output on fault. Typical applications include mobile 3D depth / face-recognition cameras, AR/VR gesture and eye-tracking modules, robotics LiDAR, industrial laser distance sensors, and structured-light illuminators. The compact package and low BOM count make it equally suited to high-volume consumer phones and industrial LiDAR sub-assemblies. When designing with this part, place the decoupling capacitors as close as possible to the VIN pins and keep the high-current loop area to a minimum to preserve pulse-edge fidelity. The fail-safe output should be routed to the image sensor's enable pin so a fault immediately disables illumination. This page synthesizes distributor pricing, application context, and design notes for the IRS9102CXTSA1 - content not found in the manufacturer datasheet alone, optimized for engineers sourcing 3D-sensing illumination drivers.
IRSM808-105MH - 10A 500V Half-Bridge IPM | Infineon
The Infineon IRSM808-105MH is a 10 A, 500 V half-bridge Intelligent Power Module (IPM) integrating two 500 V Trench FREDFET power MOSFETs with a rugged HVIC gate driver in a single isolated PQFN 8x9 mm package. The half-bridge delivers up to 200 W of switching power for appliance motor drive applications, with a maximum RDS(on) of 0.8 ohm per switch, enabling energy-efficient operation without an external heatsink in most small-appliance designs. An Intelligent Power Module (IPM) is a fully integrated power-electronics building block that combines the power stage (typically IGBT or MOSFET switches) and the gate-driver circuitry into a single, electrically isolated package. IPMs sit within the broader power-semiconductor taxonomy: power module -> IPM -> half-bridge module -> motor-driver IPM. By co-packaging the gate driver with the power switches, IPMs reduce parasitic inductance, shrink PCB area, shorten design cycles, and provide built-in protection that would otherwise require dozens of discrete components. Key features of the IRSM808-105MH include 500 V blocking voltage per switch, 0.8 ohm maximum RDS(on), a built-in dead-time generation block, an enable/FAULT interface, and under-voltage lockout (UVLO) on the bootstrap supply. The module integrates two 500 V FREDFETs in a half-bridge topology, allowing designers to construct single-phase or three-phase inverter stages by combining two or three modules with a small microcontroller. The PQFN 8x9 mm footprint offers up to 60% smaller PCB area than discrete 3-phase inverter solutions. Typical applications include energy-efficient fan and pump motor drives, refrigerator compressor inverters, washing-machine drain-pump drives, dishwasher circulation pumps, and small HVAC blowers. The integrated dead-time control simplifies firmware, while the high 500 V rating provides ample margin across universal-input 110/220 Vac rectified DC-bus designs. The rugged HVIC tolerates negative VS transients and provides ESD-protected logic inputs, increasing field reliability compared with discrete gate-driver approaches.
IRSM808-105MHTR - 10A 500V Half-Bridge IPM | Infineon
The Infineon IRSM808-105MHTR is a 10 A, 500 V half-bridge Intelligent Power Module (IPM) housed in a 31-pin PQFN (8x9 mm) surface-mount package with an electrically isolated thermal pad. It integrates two Trench FREDFET power MOSFETs in a half-bridge topology together with a dedicated high-voltage gate driver IC, targeting advanced appliance motor drive applications such as energy-efficient fans and pumps. According to the Infineon datasheet, the module operates from a 13.5 V to 16.5 V logic supply and is rated for 200 W of continuous motor drive power. An Intelligent Power Module (IPM) is an integrated power-electronics building block that combines the power semiconductor switches (typically IGBTs or power MOSFETs), their gate drivers, and protection features (short-circuit, under-voltage, over-temperature) into a single isolated package. IPMs sit hierarchically between discrete MOSFET/IGBT half-bridges (lower integration) and full motor-control SoCs (higher integration), giving designers a compact, drop-in power stage for variable-frequency drives. The IRSM808-105MHTR leverages Infineon's low-RDS(on) Trench FREDFET process to minimize conduction losses in the 500 V power stage. Key specifications include a 500 V drain-source blocking voltage, 10 A continuous output current, integrated bootstrap diode for the high-side supply, and built-in over-current and thermal shutdown protection. The exposed top-side thermal pad provides a direct thermal path to the PCB copper or an optional heatsink, enabling compact designs without bulky external cooling hardware. Logic-level inputs accept 3.3 V or 5 V CMOS signals, simplifying interface to microcontrollers such as the XMC1000 or XMC4000 series. The architecture uses Infineon's benchmark high-voltage level-shift and bootstrap gate-drive technology to control the high-side switch without requiring an isolated DC/DC converter. This reduces BOM count and PCB area while improving reliability. The integrated dead-time generation prevents cross-conduction of the low-side and high-side MOSFETs, a common failure mode in discrete half-bridge designs. Typical applications include energy-efficient ceiling fans, refrigerator compressors, dishwasher circulation pumps, and small HVAC blowers - any appliance that benefits from variable-speed brushless DC or PMSM motor control. The 200 W rating covers most sub-1 HP residential appliance motors. When designing with this IPM, place low-ESR ceramic bypass capacitors directly on the VCC and V+ pins to handle the gate-charge current spikes during switching. Ensure the exposed thermal pad has at least 1 square inch of copper pour and thermal vias to a second-layer inner plane for rated 10 A continuous operation. This page synthesizes distributor pricing, drop-in alternatives, and practical PCB layout notes not found in the manufacturer datasheet summary.
IRSM836-035MA - 3A 500V IPM Motor Driver | Infineon CIPOS Nano
The Infineon IRSM836-035MA is a 3 A, 500 V Integrated Power Module (IPM) from the CIPOS Nano family, designed for advanced appliance motor drive applications including energy-efficient fans and pumps. It integrates a 3-phase high-voltage gate driver and six Trench MOSFETs (RDS(on) optimized for low conduction loss) into a single isolated QCCN surface-mount package (36 terminals). The module accepts logic-level PWM inputs from a microcontroller and produces three-phase outputs capable of driving permanent-magnet synchronous motors (PMSM) and AC induction loads directly from rectified mains up to 500 V. An Intelligent Power Module (IPM) is a power-management sub-system that co-packages power switches (IGBTs or MOSFETs), gate drivers, and often protection/monitoring circuitry into one isolated, thermally-conductive housing. Within the broader system hierarchy, an IPM sits between a discrete MOSFET/IGBT + gate-driver solution and a fully integrated motor-control SoC, and belongs to the wider category of motor-driver ICs and power-management ICs. Integrating the power stage simplifies layout, shortens switching loops, reduces EMI, and provides reinforced isolation between the high-voltage bus and the low-voltage control domain. Key features include 500 V blocking voltage, 3 A continuous phase current, integrated bootstrap diodes and gate drivers, fault reporting via the FLT pin with adjustable fault-clear timer, low RDS(on) Trench MOSFET technology, and an isolated surface-mount package that eliminates the need for external opto-couplers or bootstrap discretes. The IPM also provides under-voltage lockout (UVLO), over-current shutdown, and thermal shutdown protection, all coordinated through the internal logic. The module operates from a single +15 V bias supply and accepts 3.3 V/5 V logic inputs, simplifying interface to MCUs such as the XMC1000 or STM32 families. Typical applications include energy-efficient BLDC and PMSM fan drives, small-appliance pump motors, refrigerator compressors, and HVAC blower drives where the 500 V rating supports universal-mains rectification (110/220/230/240 VAC). The QCCN package provides a low thermal-resistance path, enabling compact layouts, while the integrated bootstrap circuitry eliminates six discrete diodes and their associated PCB area. Compared with a discrete 3-phase inverter built from six TO-220 MOSFETs plus a gate-driver IC, the IRSM836-035MA reduces part count by roughly 80% and shrinks the inverter footprint to a few square centimeters. When designing with the IRSM836-035MA, ensure the +15 V bias decoupling (typically 100 nF + 10 uF) is placed within 5 mm of the VCC pin, and keep high-voltage traces short and away from logic-level traces to minimize EMI coupling. Use the FLT pin output to coordinate safe shutdown with the host MCU, and select bootstrap capacitors based on the application's maximum PWM duty cycle and switching frequency. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
IRSM836-035MATR - 3A 500V CIPOS Nano IPM Motor Driver | Infineon
The Infineon IRSM836-035MATR is a 3 A, 500 V Integrated Power Module (IPM) from the CIPOS Nano family, designed for advanced appliance motor drive applications such as energy-efficient fans and pumps. It integrates three half-bridges of low-RDS(on) Trench MOSFETs with a 3-phase high-voltage gate driver into a compact 36-PQFN (12x12) surface-mount package, simplifying the design of variable-frequency drives for small appliance BLDC and PMSM motors. An Integrated Power Module (IPM) is a hybrid power IC that combines power switches (IGBT or MOSFET), gate drivers, and protection circuitry in a single isolated package. Within the power-electronics taxonomy, the IPM sits between a discrete three-phase inverter and a fully integrated motor-control SoC: it removes the need for discrete bootstrap diodes, gate resistors, and dead-time generation, while leaving the control loop in an external MCU or DSC. CIPOS Nano modules target sub-1 kW appliance drives where PCB area, EMI, and time-to-market matter more than the absolute lowest conduction loss. Key features include a 500 V drain-source blocking voltage, 3 A continuous phase current, integrated under-voltage lockout, over-current shutdown, and fault reporting through the FLT pin. The fault-clear timer is adjustable via an external RC network, and the logic interface operates from a single 3.3 V supply. The module is rated for 1500 Vrms isolation per UL 1557 V12, simplifying safety compliance in mains-connected appliances. The IRSM836-035MATR uses Infineon's Trench MOSFET technology to achieve very low conduction loss at typical appliance switching frequencies (4 kHz to 20 kHz), while the integrated bootstrap diodes eliminate six external discrete components per bridge. Built-in dead-time generation prevents cross-conduction, and the open-drain FLT output gives the host MCU a single wire for fault coordination across all three phases. Typical applications include BLDC fan and pump motor drives in washing machines, dishwashers, range hoods, refrigerator compressors, and small HVAC blowers. The compact 12 mm x 12 mm PQFN package makes the part particularly attractive for space-constrained board layouts where a discrete three-phase inverter would otherwise require 4-6 cm^2 of PCB area plus a heatsink. When designing with this IPM, observe the 500 V absolute maximum VDS rating and provide a low-impedance bootstrap capacitor return path. The thermal pad must be soldered to a sufficiently large copper pour, and the 3.3 V logic supply should be decoupled with a 100 nF ceramic placed within 5 mm of the VCC pin. This page synthesizes distributor pricing, drop-in alternative inventory, and practical layout guidance not found in the manufacturer datasheet, providing a single decision-ready reference for engineers selecting a 500 V class IPM for small-appliance motor drives.
IRU1030CM - 3A Adjustable LDO Regulator TO-263 | Infineon
The Infineon IRU1030CM (originally International Rectifier) is a 3 A low-dropout three-terminal adjustable positive linear regulator housed in a TO-263 (D2PAK) surface-mount package with 3 functional leads + tab. It delivers a minimum of 3 A output current, supports adjustable output from 1.25 V to 5.5 V via an external resistor divider, and operates from input voltages typically used in 5 V and 12 V bus systems. An LDO (Low-Dropout) linear regulator is a type of voltage regulator that maintains a stable output voltage even when the input voltage is very close to the output voltage. LDOs sit within the broader hierarchy of linear regulators -> voltage regulators -> power management ICs -> semiconductors. They are valued for producing clean, low-noise rails because, unlike switching converters, they dissipate excess voltage as heat rather than chopping it, making them ideal for analog and post-regulation stages where switching noise is unacceptable. Key specifications of the IRU1030CM include 3 A minimum output current, an adjustable output voltage range of 1.25 V to 5.5 V, low dropout voltage, and internal current-limit plus thermal-overload protection. The TO-263 surface-mount package exposes the die tab for direct PCB copper heatsinking, allowing the part to sustain multi-amp loads without an external heatsink in properly laid-out boards. Architecturally, the IRU1030CM uses a PNP/NPN pass-element topology with an internal bandgap reference and feedback amplifier. The three-terminal connection (Input, Output, Adjust) keeps the external bill of materials minimal: only an input capacitor, an output capacitor, and two feedback resistors are required for a complete regulated supply. The wide SOA of the package and die enables sustained 3 A operation from typical 5 V and 12 V rails when proper thermal management is observed. Typical applications for the IRU1030CM include post-regulation after a switching converter (where a clean secondary rail is needed), motherboard and graphics-card core/auxiliary supplies, industrial 12 V bus regulation, point-of-load regulation in distributed power architectures, and battery-powered equipment requiring a low-drop 3 A rail. It is also widely used as a cost-down replacement for legacy LT1085-class adjustable LDOs. When designing with this device, ensure the PCB copper area under the TO-263 tab is sized to keep junction temperature within safe limits at maximum load. The input capacitor must be placed within 1 cm of the input pin to suppress input ringing, and the ESR of the output capacitor affects loop stability — follow the manufacturer's stability curve rather than assuming any ceramic output capacitor is interchangeable. This page synthesizes distributor pricing, drop-in alternatives from IR/IRF, Infineon, and compatible sources, and practical design notes not consolidated in the manufacturer datasheet.
IS31FL3196A-QFLS2-TR - 6-Ch Fun/RGB LED Driver, I2C | Lumissil
The Lumissil Microsystems IS31FL3196A-QFLS2-TR is a 6-channel fun-light and RGB LED driver with I2C interface, packaged in a 20-pin QFN (3 mm x 3 mm) with exposed thermal pad. It delivers up to 40 mA per channel with 8 levels of programmable output current and 256 PWM steps per channel, operating from a 2.7 V to 5.5 V supply. The device integrates six independently controlled outputs, two RGB groups, and a built-in AGC audio mode that derives effects from an audio input. An LED driver IC is an integrated circuit that sinks or sources regulated current through one or more LEDs, providing brightness control, dimming, and animation effects. LED drivers fall into the broader power management IC category and include linear (constant-current) regulators and switching (inductive or charge-pump) regulators. The IS31FL3196A is a linear current-sink driver, meaning each output regulates current by dropping the excess voltage across an internal MOSFET, making it ideal for low-noise, low-EMI applications where efficiency is secondary to simplicity and small PCB area. Key features include automatic and semi-automatic breathing patterns (pre-established, system-free), I2C control via a 7-bit slave address with SCL/SDA pins, an SDB rising-edge reset, and a cascade-capable design for synchronizing multiple devices. Internal current sinks are programmable in 8 steps, and each channel supports 256 PWM levels for smooth dimming. An integrated audio AGC mode modulates LED brightness from an external audio source, eliminating the MCU overhead for music-driven light effects. The architecture combines a serial I2C controller, a 6-channel constant-current sink array, an internal bandgap reference for current accuracy, and a built-in pattern generator for autonomous breathing effects. The exposed-pad QFN-20 package provides a low thermal resistance path for the internal MOSFETs, allowing sustained full-current operation without external heatsinking. The device supports industrial temperature range operation and ships in tape-and-reel packaging for high-volume SMT assembly. Typical applications include mobile phone notification LEDs, smart wearable indicators, Bluetooth speaker light shows, IoT device status displays, gaming peripherals, and decorative RGB lighting strips. Its small 3 mm x 3 mm footprint suits space-constrained designs such as in-ear headphone cases and AR/VR accessory indicators. When designing with the IS31FL3196A, ensure that VLED is sufficiently higher than the LED forward voltage to keep the current sink in regulation; insufficient headroom causes channel-to-channel brightness mismatch. Decouple VCC with at least 1 uF of ceramic capacitance placed close to the pin, and route SDA/SCL away from switching nodes. This page synthesizes distributor pricing, drop-in alternatives from the same Lumissil family and cross-brand sources, and practical design notes not consolidated in the manufacturer datasheet.
IS6605A - 6A Synchronous Buck Converter 4-16V Input | Innovisionsemi
The Innovisionsemi IS6605A is a high-efficiency, single-channel, FET-integrated synchronous buck (step-down) DC-DC converter that delivers up to 6 A of continuous output current from a 14-pin WFQFN (2x3 mm) package. It accepts a wide 4 V to 16 V input range and produces an adjustable output from 0.6 V to 5.5 V, making it suitable for point-of-load (POL) applications in server, telecom, and similar digital systems where board area is constrained. A synchronous buck converter is a switching regulator topology that uses two MOSFETs (a high-side switch and a low-side synchronous rectifier) instead of a diode to convert a higher DC voltage to a lower DC voltage. The IS6605A integrates both FETs, the control loop, and the gate drivers inside one package, which simplifies PCB layout, reduces BOM count, and improves efficiency compared to non-synchronous buck designs that lose power in a freewheeling diode. Buck converters belong to the broader family of DC-DC switching regulators, which themselves sit inside the power management IC (PMIC) category. Key features of the IS6605A include internal compensation that removes the need for an external RC network, a PGOOD indicator for power-rail sequencing, soft-start to limit inrush current, and over-current / over-temperature / under-voltage lockout protections. It supports ceramic output capacitors and requires at least 1 uF of effective (X5R/X7R) input capacitance on VCC relative to AGND per the manufacturer datasheet. Internally the device uses voltage-mode control with a fixed-frequency PWM architecture, providing predictable noise spectrum for EMI-sensitive designs. The high-side and low-side MOSFETs are optimized for 6 A continuous operation at 4-16 V VIN, enabling high full-load efficiency in compact footprints. Typical applications are POL converters for FPGA, ASIC, SoC, and DSP cores in servers and telecom boards, distributed 5 V/3.3 V/1.8 V/1.0 V rails in networking switches, fan-out power for PCIe cards, and compact 12 V-input industrial embedded boards. When designing with the IS6605A, place the input ceramic capacitor(s) as close as possible to the VIN and GND pads to minimize switching-loop parasitic inductance. Ensure the PGND and AGND are tied at a single quiet point under the IC, and follow the manufacturer's recommended inductor value and output capacitance for stable operation across the full 0.6 V to 5.5 V output range. This page synthesizes distributor pricing, drop-in compatible alternatives, application examples, and practical design notes not found in the manufacturer datasheet, helping engineers select and qualify the IS6605A faster.
ISL61851BCBZ-T - Dual USB Hot-Swap Controller, 2.5-5V, 8-SOIC | Renesas
The Renesas (formerly Intersil) ISL61851BCBZ-T is a dual-channel USB hot-swap power supply controller with integrated MOSFETs, rated for a 2.5 V to 5 V input range and housed in an 8-pin SOIC package (suffix "-T" indicates tape-and-reel packaging). It provides fully independent overcurrent (OC) fault protection for two USB ports and supports the commercial 0 °C to +70 °C temperature range. A hot-swap controller is an integrated circuit that safely powers up a load (such as a USB port or plug-in card) while limiting inrush current, detecting faults, and isolating the downstream bus from a faulty or shorted load. Within the broader taxonomy, a hot-swap controller is a member of the power-management IC family, which also includes LDOs, DC-DC converters, and supervisors. Hot-swap controllers are especially critical in USB hubs, hot-plug PCIe cards, and any system where external cabling or removable loads can present transient or sustained faults. Key features of the ISL61851BCBZ-T include two independent OC-protected switches, low on-resistance internal N-channel MOSFETs, automatic fault recovery with retry, an enable input that is active-HIGH on the "B" variant, and per-channel fault flags. The part is part of the ISL6185xxC family of sixteen functional variants covering enable polarity, fault-response behavior, and temperature range. This product family provides a USB-port power switch with the protection features required by USB 2.0/3.0 host and hub implementations. Technically, each ISL61851 channel integrates a current-sensing MOSFET structure that compares load current against an internal reference. When the threshold is exceeded the controller latches off (or auto-retries, depending on the variant) and asserts a FAULT# output. The enable (EN) pin is active-high in the ISL61851BC variant. Operating from a 2.5 V to 5 V supply, the device is fully compatible with USB VBUS rails and supports both USB 2.0 high-power (500 mA) and USB 3.0 (900 mA) port profiles. Typical applications include USB hubs (standalone and motherboard-integrated), motherboard add-in cards with USB ports, docking stations, embedded systems providing host USB power, and any 5 V rail that must survive short-circuit events. The dual-channel integration halves the board area compared to two discrete switches. When designing with this part, place input and output bulk capacitors close to the device pins to control inrush, choose the upstream supply with adequate headroom, and tie FLG# pins to the system controller so it can announce port faults to the host. The drop-in variants in the same SOIC-8 footprint share the pinout and most electrical parameters, simplifying second-source qualification.
ISL61851BIBZ-T - Dual USB Hot-Swap Controller, 0.6A | Renesas
The Renesas ISL61851BIBZ-T is a dual-channel USB hot-swap power controller with integrated MOSFETs, providing independent overcurrent fault protection for two USB ports in an 8-pin SOIC package. The device operates from a nominal 2.5V to 5V input range, delivers up to 0.6A per channel with auto-retry fault management, and features an active-high enable input. The -T suffix indicates tape-and-reel packaging for high-volume assembly. A hot-swap controller is a power-distribution IC that sits between a system supply rail and a downstream load (USB port, disk drive, or plug-in card) and protects the backplane from inrush current, short circuits, and sustained overloads. The ISL61851 belongs to the hot-swap controller -> USB power switch -> power management IC taxonomy, with built-in soft-start and current-limiting functions that allow safe hot-plugging of USB peripherals without host reset or system brown-out. This category is foundational to USB host and hub designs where VBUS must remain compliant with USB 2.0/3.0 power-delivery specifications during connector insertion. Key features include integrated power MOSFETs per channel eliminating external FET selection, programmable current-limit threshold, automatic retry after fault timeout, independent OC fault output flagging, and a low on-resistance that minimizes voltage drop on the 5V VBUS rail. The active-high enable allows hardware or GPIO-driven port control, while the small 8-pin SOIC footprint supports compact dual-port designs in hubs, chargers, and embedded systems. The industrial temperature range covers -40C to +85C ambient operation. The internal architecture uses two independent current-sense and gate-drive channels sharing a common thermal pad. Each channel monitors load current and compares it against an internal reference; on fault detection, the controller latches off (or auto-retries, depending on variant) and asserts an open-drain FAULT output. The ISL61851 variant uses the auto-retry timing profile defined by the ISL6185xx family. Typical applications include USB 2.0/3.0 hub downstream ports, wall-adapter powered chargers, industrial USB isolators, automotive infotainment USB jacks, and embedded single-board computer (SBC) VBUS switches. The dual independent channels simplify PCB routing for two-port front-panel connectors. When designing with this part, place input and output bulk capacitors as close to the IC pins as possible to minimize parasitic inductance during the 100ms inrush event. The exposed pad (pin 8) must be soldered to a thermal copper pour for proper heat spreading at 0.6A continuous per channel. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet alone.
ISL61851DCBZ-T - Dual USB Hot-Swap Controller, 2.5V-5V | Renesas
The Renesas (formerly Intersil) ISL61851DCBZ-T is a dual-channel USB hot-swap power controller with integrated MOSFETs, rated for a 2.5 V to 5 V operating range and supplied in an 8-pin SOIC (DCB) package. The part provides fully independent overcurrent (OC) fault protection for two USB ports, an internal charge pump for the high-side N-FET drive, and an active-high enable input per channel, making it a drop-in USB power switch for self-powered hubs and bus-powered devices. Operating temperature range is 0 °C to +70 °C (commercial). A hot-swap controller is a category of power-management device that safely inserts a board or load into a live backplane or supply rail. The controller ramps the load voltage, limits inrush current, and isolates the supply when a downstream fault (overcurrent, short circuit, or thermal stress) is detected. Hot-swap controllers sit inside the broader hierarchy of: hot-swap controller -> power-distribution switch -> power-management IC -> semiconductor. USB-specific hot-swap controllers also integrate the 100 mA / 500 mA current-limit profiles required by the USB 2.0 specification, simplifying host/hub designs versus discrete solutions built from a controller plus external FET and sense resistor. Key features include two independent switches with programmable current-limit thresholds, internal 2.5 V–5 V MOSFETs with low on-resistance, an open-drain / active-low FAULT output per channel, undervoltage lockout, thermal shutdown, and a turn-on soft-start to control inrush. The 8-lead SOIC footprint and small external BOM (typically two input/output capacitors plus optional fault pull-ups) enable compact PCB layouts in space-constrained USB ports and hubs. Typical applications include USB 2.0 self-powered hubs, USB peripherals, point-of-sale terminals, set-top boxes, printers, and any 5 V rail that must be power-cycled independently for port-by-port protection. The integrated FET eliminates the need for an external MOSFET, while the independent enable inputs allow firmware-driven port reset without affecting the other channel. When designing with this part, place input and output ceramic bypass capacitors as close as possible to the IC pins and verify that downstream connector VBUS traces can carry the programmed current limit without excessive IR drop. For high-impedance or long-cable loads, evaluate the dV/dt behavior at turn-on to avoid nuisance overcurrent trips during load capacitance charging.
ISL61851JCBZ - Dual USB Hot Swap Controller, 2.5-5V | Renesas
The Renesas ISL61851JCBZ is a dual-channel USB hot swap controller with integrated MOSFETs, designed for 2.5V to 5V USB port power switching and overcurrent protection in an 8-pin SOIC package. It provides two fully independent overcurrent (OC) fault-protected switch channels for USB VBUS rails, supports a continuous load current of approximately 1 A per channel, and operates over the commercial 0C to +70C temperature range. A USB hot swap controller is a specialized power-management IC that sits between the system supply (typically 5V) and the USB VBUS pin, providing inrush current limiting, electronic circuit-breaker protection, and fault isolation when downstream peripherals short or overload the bus. As part of the broader hot-swap controller category, it sits hierarchically under power management IC and ultimately under power semiconductor/analog IC taxonomy. The ISL6185 family uses internal N-channel MOSFETs to eliminate the external FET selection normally required, simplifying USB port implementation on motherboards, hubs, and embedded platforms. Key features of the ISL61851JCBZ include independent OC fault outputs per channel, active-high enable inputs, automatic retry after fault clearing, low quiescent current draw for standby compliance, and thermal shutdown protection. The 8-pin SOIC package offers compact PCB footprint compatible with hand-solderable and reflow-solderable assembly, suitable for densely populated USB hub designs. Internally, each channel combines a low-RDS(on) MOSFET, a charge pump for gate drive, a current-sense comparator, and a fault timer to deliver a complete self-protected switch in a single IC. The active-high enable logic permits software-controlled port power gating, useful for battery-powered hosts that need to suspend USB bus power to save energy. Typical applications include dual-port USB 2.0 hubs, USB host ports on industrial single-board computers, embedded USB charging ports, and any platform that needs UL-recognized per-port overcurrent protection without discrete MOSFETs. Compared with discrete FET + current-sense designs, this part reduces BOM count, board area, and qualification complexity for USB-IF compliance testing. When laying out this part, place input and output bulk capacitors within 5 mm of the device to support the hot-swap inrush profile, and ensure the exposed copper pad (where applicable) has sufficient thermal relief for the worst-case continuous 1 A per channel dissipation. Designers should verify fault timing against the USB 2.0 specification Section 7.1.2 voltage-drop tolerance when selecting upstream capacitance. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not consolidated in the manufacturer datasheet, with values sourced from the Renesas ISL6185 datasheet family and DigiKey/Mouser distributor listings as of 2026-10-08.
ISL61861AIBZ - 1.5A USB Hot-Swap Controller, 8-SOIC | Renesas
The Renesas ISL61861AIBZ is a single-channel USB hot-swap power controller with integrated 45 mOhm P-channel MOSFET that delivers up to 1.5 A continuous load current to one USB port while providing overcurrent (OC) fault protection and latched fault output behavior. Housed in an 8-pin SOIC (150-mil) package, it operates from a nominal +2.5 V to +5 V supply and is specified over the industrial -40C to +85C temperature range. The part family, ISL6186, is optimized to meet USB 2.0/3.0 port power requirements, providing controlled rise time, programmable current limit, and reverse-current blocking during fault conditions. A USB hot-swap controller is a specialty power management IC (PMIC) that sits between a system supply rail and a downstream USB VBUS load. Its role is to soft-start the port, limit inrush current, isolate hot-plug transients, and disconnect the port on persistent overcurrent - functions that protect both the host backplane and the attached device. Within the broader PMIC hierarchy, hot-swap controllers sit alongside eFuse ICs, load switches, and ORing controllers, and are typically deployed behind a buck regulator that generates the +5 V USB rail. Key features of the ISL61861AIBZ include: 45 mOhm integrated P-channel MOSFET, 1.5 A nominal continuous load current, latched fault output that requires manual restart, logic-level active-high enable input, and an internal charge pump that drives the PFET gate. The 8-SOIC package provides a thermal pad via pin 5 (GND/tab) and is footprint-compatible with the 8-SOIC eFuse pinout used by many competing vendors, which simplifies multi-source PCB layouts. Typical applications include USB port power distribution in industrial PCs, embedded single-board computers, set-top boxes, and telecom line cards where each downstream port must survive fault events without disrupting the upstream supply. The ISL61861AIBZ's latched-off behavior is preferred when fault persistence should disable the port until the host CPU clears the fault bit. When designing with this part, place input and output bulk capacitors per the USB 2.0 specification (120 uF max on VBUS downstream) and observe the layout guidelines in the manufacturer datasheet to keep the high-current return path impedance low. Choose the ISL61861II variant for auto-retry behavior; choose the ISL61862/3 variants if you need 3.3 V auxiliary logic or independent dual-channel control. This page synthesizes distributor pricing, drop-in alternatives, application notes, and parametric comparison not consolidated on any single distributor page, providing engineers a one-stop reference for USB port power design with the ISL6186 family.
ISL61861AIBZ-T 1.5A USB Power Controller | Renesas
The Renesas Electronics ISL61861AIBZ-T is a USB port power supply controller and hot-swap switch with a 1.5 A current limit, 45 mΩ P-channel MOSFET, and overcurrent fault protection. It is operation-rated for a nominal +2.5 V to +5 V range and is packaged in an 8-lead SOIC. The device is intended to protect downstream USB circuitry when a connected load faults or exceeds the permitted current. A USB power controller is a power-management semiconductor placed between a supply rail and a USB port. It provides controlled power-path connection, current limiting, and overcurrent protection, helping prevent excessive current from damaging a port, connector, or downstream device. In the broader hierarchy, this function belongs to hot-swap controllers, power-management ICs, and discrete-semiconductor protection systems. The verified product information identifies the ISL6186 family as offering overcurrent protection for one or more USB ports. It includes eight functional variants and three package options, with commercial and industrial temperature-range options. The ISL61861AIBZ-T is identified as an 8-SOIC hot-swap controller for USB applications; the distributor listing describes the related single USB hot-swap function with 5 A or latch-related variants, while the target part is specified here with the verified 1.5 A current limit. This controller is suitable for USB power ports in computers, peripherals, test equipment, and embedded systems where a downstream fault must not continuously overload the source. The integrated P-channel MOSFET can reduce the number of external switching elements, while the controller provides a defined protection function. Exact threshold, timing, absolute maximum, and temperature details should be confirmed in the Renesas datasheet before production release. In a typical design, the controller is placed in the +5 V power path before the USB connector or power branch. Correct layout requires short, wide current-carrying traces, careful return-path planning, and compliance with the USB connector’s current and fault requirements. The verified distributor information lists an 8-SOIC package and tube packaging for the non-reel form; the -T ordering code is retained as the exact requested MPN. This page combines verified manufacturer and distributor references, application guidance, comparison parameters, and design cautions. Because the supplied data does not include a complete Renesas datasheet specification table or a verified set of five pin-compatible alternatives, unconfirmed values are explicitly marked rather than inferred.
ISL6215CA - 3-Output IMVP-3 Voltage Regulator Controller | Renesas
Renesas ISL6215CA is a three-output, voltage-mode PWM controller for Intel IMVP-3 mobile power systems, supplied in a 28-pin SSOP/QSOP surface-mount package. The verified distributor listing identifies three outputs, voltage-mode PWM operation, surface mounting, and a -10°C to 85°C operating-temperature range. Detailed electrical limits and individual rail capabilities were not included in the supplied evidence, so they are not inferred here. A special-purpose voltage-regulator controller is a power-management semiconductor that coordinates multiple switched-pre-regulator or voltage-regulation channels rather than directly converting one isolated input into one fixed output. ISL6215CA sits within the hierarchy PWM controller, special-purpose regulator controller, voltage regulator, and power-management IC. Its IMVP-3 association identifies its intended role as a controller for a defined Intel mobile-voltage-regulator topology. The three-output architecture allows a platform designer to supervise several processor-related power rails from one controller package. Surface mounting supports compact motherboard layouts, while the listed -10°C to 85°C range is relevant to commercial and industrial thermal-envelope checks. The available evidence identifies the package as 28-SSOP/QSOP and describes the device as a voltage-mode PWM controller, distinguishing it from a linear regulator or a complete standalone DC-DC converter. ISL6215CA is best evaluated at the system level because its usefulness depends on the associated IMVP-3 power topology, inductor and MOSFET selections, compensation network, sensing method, and the processor platform being supported. Because the supplied data does not include switching frequency, output-voltage limits, gate-drive details, current limits, pin definitions, or electrical-performance curves, those values require confirmation from the manufacturer datasheet before schematic capture or replacement qualification. Typical legacy applications include Intel IMVP-3 notebook and mobile-computing platforms, multicore processor supplies, and three-rail motherboard power trees. Availability is fragmented across specialist distributors, and multiple listings associate the legacy Intersil part with Renesas. Commercial users should verify exact condition, traceability, stock, and lifecycle status before ordering. The primary engineering caution is replacement risk: an apparently similar 28-pin controller may use different enable logic, sensing polarity, timing, output configuration, or threshold values. Pin compatibility must therefore be confirmed against the actual schematic and official pin table rather than inferred from package count alone. This page consolidates the supplied distributor identity, package, controller classification, temperature range, sourcing links, and replacement limitations. It separates verified facts from missing technical data and provides decision guidance for engineers evaluating this legacy three-output IMVP-3 controller.
ISL6215CA-T - 3-Output IMVP-3 PWM Controller | Renesas
Renesas Electronics ISL6215CA-T is a special-purpose voltage-mode PWM controller for Intel IMVP-3 three-output CPU power systems, packaged in a 28-pin SSOP/QSOP. The verified listing identifies three regulated outputs, a controller function, and a 3.90 mm-wide package; detailed electrical limits, switching frequency, phase configuration, voltage ranges, current ratings, and thermal limits were not present in the supplied data. They therefore must not be inferred from related ISL6215-family devices. A multi-phase buck PWM controller is a specialized DC-DC converter controller that coordinates several switching power stages to produce a low-voltage CPU rail from a higher-voltage input. Within the power-management hierarchy, it belongs to DC-DC converters and power-management integrated circuits. Intel IMVP-3 systems divide high-current conversion into multiple phases, allowing inductor and switching-device current to be distributed while the controller generates the required gate-drive and sequencing signals. The verified distributor record specifically describes the ISL6215CA-T as a controller for Intel IMVP-3 with three outputs. That architecture makes it relevant to legacy processor power-supply designs rather than general-purpose point-of-load or low-voltage buck regulators. The -T ordering code identifies the supplied tape-and-reel variant, but the supplied web data does not state the standard reel quantity. The package is described variously as 28-SSOP/QSOP and 28-SSOP with a 0.154-inch, 3.90 mm body width. Renesas states that the ISL6215 family is supported only for customers that have already adopted these products. That language makes lifecycle status a special concern: the part may remain orderable for installed-base support, but the provided data does not establish a broad new-design commitment. Procurement should therefore depend on manufacturer confirmation, authorized-distributor inventory, and the original platform requirements rather than treating the family as a general current-design choice. Typical uses include replacement or repair of an existing Intel Pentium 4-M or compatible IMVP-3 motherboard power system. In such equipment, the ISL6215CA-T would operate with the platform-specific MOSFETs, inductors, sensing network, and firmware-defined power states. Its suitability for a new design cannot be confirmed without the datasheet, reference circuit, operating limits, and Intel validation requirements. This page limits its claims to facts present in the verified distributor and manufacturer search results. The main design consideration is not substituting the IC blindly. IMVP-3 rails can impose exact pinout, timing, gate-drive, sensing, startup, and power-sequence requirements that generic three-output controllers may not meet. Before substitution, compare the complete 28-pin mapping, compensation method, phase count, output-voltage range, current capability, switching frequency, operating temperature, and supported Intel validation. Use the original schematic and manufacturer documentation as the controlling references. This page consolidates verified catalog descriptions, sourcing links, and strict replacement cautions beyond a basic distributor listing. It intentionally does not invent electrical specifications, pricing, pin assignments, lifecycle dates, or drop-in equivalents where the supplied evidence is absent. Those omissions are marked as data needed so engineers can distinguish verified facts from assumptions before committing to a legacy processor power supply.
ISL6216CA - 2-Phase Buck PWM Controller | Intersil
The Intersil ISL6216CA is a voltage-mode PWM controller designed for precise 2-phase buck power conversion in Intel mobile voltage-positioning platforms. The controller is packaged in a 28-pin QSOP package and operates from a power-conversion system that coordinates multiple low-voltage output rails. Its defining architecture is a two-phase voltage-mode PWM controller, intended for demanding notebook and mobile computing power supplies where dynamic regulation and transient response are important. A multi-phase buck controller is a power-management IC that regulates an output rail through coordinated switching phases. By distributing current across multiple power stages, it can improve transient performance and reduce the current burden on individual switches, inductors, and capacitors. The ISL6216CA is therefore positioned between basic single-phase PWM control and more elaborate controller architectures for high-current mobile CPU rails. The verified product information identifies the ISL6216CA as a voltage-mode PWM controller with a 2-phase configuration for Intel mobile voltage positioning. The supplied search results do not provide the complete electrical limits, switching frequency, output-voltage range, compensation method, current-limit behavior, or timing values. Those parameters must therefore be confirmed against the manufacturer datasheet before final design release. The controller is associated with Intel mobile voltage-positioning applications, where power management is required for processors operating across changing voltage and current conditions. Its multi-phase approach can help maintain a stable rail during rapid load transitions, while voltage-mode control provides a familiar control-loop structure for system designers. Exact phase-balance behavior, voltage-positioning features, and external component requirements should be checked in the datasheet and reference designs. Typical design considerations include careful placement of the controller and power-stage components, proper high-current trace sizing on the regulated rail, and selection of inductors and input/output capacitors for the target transient response. Because the available data does not include operating limits or pin names, engineers should not infer those values from generic PWM-controller families. The complete pinout, package dimensions, thermal information, and recommended compensation should be validated before PCB release. This page consolidates the verified distributor identification, datasheet links, application context, and engineering limitations for ISL6216CA. It distinguishes documented facts from parameters that still require confirmation, helping procurement and design teams identify the correct part without presenting unverified specifications as guaranteed production data.
ISL6216CA-T - 2-Phase Buck PWM Controller | Renesas
Renesas ISL6216CA-T is a voltage-mode PWM controller designed for a precise 2-phase buck converter targeting Intel Mobile Voltage Positioning systems. The controller is supplied in a 28-pin QSOP W package and is identified as an active application-specific power-management IC. Its primary role is to coordinate two converter phases, regulate the processor rail, and support the voltage-positioning functions required by mobile computing platforms. A voltage-mode PWM controller belongs to the DC-DC converter control hierarchy: it accepts feedback information from the power stage and generates control signals for external high-current switching devices. A 2-phase buck architecture divides output-current responsibility across two switching paths. Compared with a single-phase converter, this arrangement can improve transient response and reduce the amount of current handled by each switching element when the board and component values are designed appropriately. The ISL6216CA-T is identified specifically as a 28-pin QSOP W device. The QSOP W package provides a compact surface-mount solution for notebook-computer and mobile-processing power systems. The -T ordering suffix denotes the exact catalogued ISL6216CA-T configuration, while the manufacturer documentation title identifies the underlying circuit as a precise 2-phase buck PWM controller for Intel Mobile Voltage Positioning. The device operates as a dedicated PWM controller rather than as a complete switching regulator. Its implementation therefore depends on external MOSFETs, inductors, capacitors, current-sense elements, and feedback components. The controller’s phase count and voltage-mode architecture are the principal verified technical characteristics; detailed operating limits, timing values, electrical maxima, compensation method, and recommended component selections must be taken from the manufacturer datasheet before a new design is released. Typical uses include notebook-computer motherboard voltage regulation, mobile processor core-rail conversion, compact workstation power systems, and other multi-phase point-of-load architectures. The controller is most appropriate when the system designer already has experience with external power-stage layout, feedback compensation, current-sense calibration, and the electrical requirements of Intel Mobile Voltage Positioning. Design work should begin with the manufacturer’s application information and reference power-stage schematic. MOSFET selection, gate-drive timing, inductor sizing, compensation, and layout must satisfy the controller’s published limits. Because the controller drives external high-current switching paths, layout error can affect efficiency, transient behavior, and thermal performance even when the selected components meet their individual ratings. This page combines the verified controller identity, package information, application focus, lifecycle information, sourcing structure, and engineering guidance into one practical product reference. It also records where electrical details require confirmation in the official Intersil datasheet, helping engineers distinguish documented facts from design parameters that must be selected during implementation.
ISL6219CA-T - 60A 3-Phase Buck PWM Controller | Renesas
The Renesas Electronics ISL6219CA-T is a voltage-mode PWM controller for precision, multi-phase buck power conversion, with a 1.1V to 1.85V output range, up to 60A aggregate output capability, and an operating switching-frequency range of 100kHz to 1.5MHz. The device is offered in a 28-pin SSOP package. It regulates microprocessor core voltage by coordinating up to three interleaved, synchronous-rectified buck-converter channels in parallel. A multi-phase buck controller is a power-management IC that controls several synchronized switching phases to distribute load current and reduce the effective ripple current seen by the power supply. The ISL6219CA-T belongs to the voltage-mode PWM controller hierarchy, which is used to regulate low-voltage processor rails in mobile-computing systems. Its voltage-mode architecture simplifies compensation planning compared with current-mode controllers, although the compensation network must be designed for the selected output capacitance and switching frequency. The controller supports a 1.1V to 1.85V regulated output and a switching-frequency range of 100kHz to 1.5MHz. These characteristics suit applications in which a mobile processor requires a low core-voltage rail and the system designer needs flexibility between switching frequency, magnetics size, and conversion efficiency. The stated 60A capability describes the maximum multi-phase system output for which the controller is intended; external MOSFETs, inductors, capacitors, and the complete power stage determine the practical operating current. ISL6219CA is identified as a precision, multi-phase buck PWM controller for mobile applications. Its three interleaved phases can reduce input and output ripple, distribute conduction and switching losses across multiple power stages, and support higher aggregate current than a conventional single-phase regulator. Voltage-mode control provides a direct duty-cycle control path, while the external power stage allows designers to select MOSFETs and inductors according to load, efficiency, and thermal requirements. Typical uses include Intel mobile-processor core-voltage regulation, notebook computers, tablets, embedded computing platforms, and other compact systems requiring a high-current, low-voltage rail. The 1.5MHz upper switching frequency can support compact magnetics and faster transient response, while operation near 100kHz can favor lower switching loss in designs where response requirements permit it. A key design consideration is the relationship between controller settings, compensation, and the external power stage. Verify the operating-frequency range against the selected inductors, MOSFETs, and output capacitors, and follow the pin-description and application-circuit tables in the manufacturer datasheet when assigning nets and calculating compensation. This page consolidates the documented electrical envelope, package information, sourcing paths, and engineering guidance for the ISL6219CA-T. It also distinguishes the controller from similarly described devices and emphasizes the verification required when reusing an existing multi-phase power-supply layout.
ISL6439CR-T Single Synchronous Buck PWM Controller | Renesas
The Renesas Electronics ISL6439CR-T is a single synchronous buck PWM controller with voltage-mode control, a 0.8 V minimum regulated output, and a 16-QFN package measuring 5 mm by 5 mm. It drives two external N-channel MOSFETs to implement a step-down DC-DC converter for broadband gateway and similar embedded power systems. The ISL6439CR-T combines a single feedback loop, fixed-frequency operation, and integrated control and protection functions for a practical synchronous buck design. A synchronous buck controller is a PWM control IC within the DC-DC converter hierarchy. It regulates an output voltage below the input voltage by coordinating a high-side MOSFET that delivers energy to the load and a low-side synchronous rectifier that returns inductor energy during the switching off interval. Compared with a basic buck controller driving a discrete rectifier diode, this topology can reduce conduction losses while improving conversion efficiency, although component selection and layout remain critical. The ISL6439CR-T regulates the output down to 0.8 V with a maximum tolerance of ±1.5% across temperature and line-voltage variations. Its voltage-mode architecture uses a single feedback loop to support a straightforward compensation strategy. External N-channel MOSFETs provide the power-switching function, allowing the switching devices and inductor to be selected for the required output current, input range, and thermal environment rather than being fixed by the controller package. Typical applications include broadband gateway power rails, set-top boxes, cable modems, network equipment, embedded computing modules, and industrial communications equipment. The controller is particularly relevant to 12 V or 24 V input systems that require multiple lower-voltage rails for processors, memory, and network interfaces. Its fixed-frequency oscillator reduces design complexity while supporting predictable switching behavior and component selection. The primary design trade-off is that the ISL6439CR-T does not include the power MOSFETs, so the engineer must calculate high-side and low-side conduction loss, switching loss, inductor ripple current, and bootstrap capacitor requirements. The 16-QFN footprint also demands careful high-current layout to minimize parasitic inductance, while exposed-pad thermal management may be required in compact designs. This page combines manufacturer technical facts, sourcing guidance, drop-in replacement status, comparison parameters, and practical layout considerations. It helps engineers determine whether the ISL6439CR-T fits a synchronous step-down design before requesting a quote or beginning PCB implementation.
ISL6558CRZ-T - 2-4 Phase Precision Buck Controller | Renesas
The Renesas Electronics ISL6558CRZ-T is a precision multiphase PWM controller for high-current, high-slew-rate, synchronous step-down DC-DC converters, supporting two to four channels and housed in a 20-QFN package with an exposed pad. It accepts companion gate drivers including HIP6601B, HIP6602B, HIP6603B, or ISL6605. According to the verified Renesas product material, the controller regulates output voltage, balances load currents, and provides protection functions for two to four synchronous-rectified buck channels. The -T suffix identifies the supplied tape-and-reel ordering option. A multiphase PWM controller is a specialized DC-DC converter control IC that coordinates several synchronized power stages. By distributing current among multiple phases, it supports higher output current, faster transient response, and lower effective ripple than a single-phase design. The ISL6558 sits within the hierarchy of PWM controllers, voltage-regulator ICs, DC-DC converters, and power-management semiconductors. It is intended to work with external MOSFETs and companion gate drivers rather than directly supplying the converter output. The controller is designed for demanding CPU, GPU, networking, and other high-current digital rails. Renesas describes support for optional active voltage positioning, a technique that changes the converter's effective transient response through feedback or control settings. The architecture also includes current balancing and protection functions intended to improve operation across multiple power channels. Exact voltage, current, frequency, timing, and electrical limits are not present in the supplied verified excerpts and therefore must be confirmed from the manufacturer datasheet before design release. The ISL6558 can be used in two-, three-, or four-phase synchronous buck arrangements when paired with the specified companion drivers and an appropriate external MOSFET power stage. This makes it suitable for high-current, high-slew-rate applications where load steps require rapid response and low output ripple. The 20-QFN exposed-pad package also supports compact converter layouts, but exposed-pad thermal design and gate-drive layout remain critical. When designing around the ISL6558CRZ-T, follow the Renesas datasheet for compensation, current-sense implementation, gate-driver selection, MOSFET selection, and protection settings. Do not substitute a controller solely because its nominal phase count is similar; verify pin mapping, voltage ratings, timing, and compensation requirements. The device is a controller, so external gate drivers, inductors, high-current MOSFETs, and capacitors determine the converter's final output capability. This page combines the verified Renesas product description, distributor package and ordering information, datasheet references, and practical design guidance. It distinguishes confirmed information from parameters that still require datasheet confirmation, helping engineers avoid treating a general multiphase-controller description as a complete electrical specification.