ATSAML11D15A-YU - 32MHz Cortex-M23 MCU | Microchip
MPN: ATSAML11D15A-YU ✓ AktifATSAML11D15A-YU Ringkasan
A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. The ATSAML11D15A belongs to the SAM L11 family of embedded controllers, combining an Arm Cortex-M23 core with a low-power sleep architecture, security hardware, and energy-conscious peripheral blocks. This product type sits between simple logic controllers and more complex application processors for connected, secure, and battery-oriented equipment.
Key features include Arm TrustZone Technology, chip-level tamper resistance, secure key storage, cryptographic support, and low active current below 25 uA/MHz. The manufacturer specifies sleep-mode current below 100 nA. Its 32-bit architecture, 32 MHz clock, 32 KB flash, and 8 KB SRAM provide a practical balance between processing capability, memory demand, and power consumption for embedded control tasks.
The Cortex-M23 core uses Armv8-M architecture and includes the security partitioning features of TrustZone. Hardware cryptographic blocks, tamper detection, and protected key storage support products that handle credentials, update data, or authenticated communications. These capabilities are more relevant than simply increasing clock speed when the end product must protect software execution boundaries or resist physical key-extraction attempts.
Typical uses include low-power sensor nodes, compact industrial controllers, secure access equipment, battery-operated condition monitoring, connected accessories, and small control systems with analog measurement. The ATSAML11D15A-YU is particularly suitable when a design needs an industrial-temperature 24-SSOP option, secure boot or key-management foundations, and low standby power without the overhead of a larger application processor.
PCB design should follow the manufacturer's package drawing and pin-description tables. Pay particular attention to decoupling, exposed analog and digital interfaces, programming access, clock configuration, and any externally connected sensitive signal. Because the device combines high-security functions with low-power operation, firmware should configure unused peripherals, security features, and wake-up sources deliberately rather than relying on default behavior.
This product page combines the manufacturer's device positioning with distributor specifications, package information, lifecycle status, and engineering-focused selection guidance. It also provides a same-footprint comparison framework for evaluating ATSAML11D15A family configurations without overlooking differences in memory, temperature grade, or delivery format.
Pilihan pengganti yang segera untuk ATSAML11D15A-YU — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera ATSAML11D15A-YU (sama faktor bentuk dan kaki) — berbeza dalam Package, RoHS Status, ADC, Active Current, Core Architecture.
ATSAML11D15A-YF
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →ATSAML11D15A-YFT
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
ATSAML11D15A-YUT
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →ATSAML11D16A-YU
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →ATSAML11D14A-YU
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →ATSAML11D15A-YU Penilaian maksimum & Ciri-ciri Elektrik
| Product Type | 32-bit Arm Cortex-M23 microcontroller |
| Processor Core | Arm Cortex-M23 |
| CPU Architecture | Armv8-M architecture |
| Maximum CPU Frequency | 32 MHz |
| Flash Memory | 32 KB (32K x 8) |
| SRAM | 8 KB |
| Active Current | Less than 25 uA/MHz |
| Sleep Current | Less than 100 nA |
| Security Architecture | Arm TrustZone Technology |
| Cryptographic Support | Crypto hardware supported |
| Tamper Resistance | Chip-level tamper resistance |
| Gambaran Suhu Operasi | -40C to +85C |
| Kemasan | 24-SSOP (0.209 in, 5.30 mm width) |
| Packaging | Tube |
| Jenis Pemasangan | Surface mount |
| Status RoHS | RoHS3 compliant |
| Status Lingkungan Hidup | Active |
| Minimum Order Quantity | 1 piece |
| Reported Lead Time | 10 weeks |
Panduan Konfigurasi Pin ATSAML11D15A-YU 24-ssop (0.209 in, 5.30 mm width)
Konfigurasi pin untuk ATSAML11D15A-YU (24-ssop (0.209 in, 5.30 mm width) pakai). IC digital ini termasuk GPIO, antaramuka komunikasi (UART, SPI, I2C), dan pin kuasa. Rujuk dokumen pengeluar untuk fungsi pin alternatif dan opsi konfigurasi. Biasa digunakan dalam rancangan sistem ter嵌入式 dan PCB.
Tiada data garisan pin yang diperoleh untuk ATSAML11D15A-YU.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
ATSAML11D15A-YU patut untuk 6 aplikasis: Battery-Powered Sensor Node, Secure Access Control Terminal, Industrial Condition Monitor, Compact Data Acquisition Controller, Connected Equipment Controller, Portable Diagnostic Device.
Battery-Powered Sensor Node
The ATSAML11D15A-YU fits low-power sensor nodes because its Cortex-M23 core operates at 32 MHz while consuming less than 25 uA/MHz, and its sleep current is specified below 100 nA. Firmware can wake periodically, acquire measurements, process them locally, and return the node to sleep without continuously powering unused peripherals. The 32 KB flash and 8 KB SRAM support compact protocol stacks and control logic, while TrustZone and secure key storage help isolate credentials used for authenticated sensor or network communication. Battery-life calculations should include regulator quiescent current, sensor excitation, radio activity, and wake-up duration rather than relying on sleep current alone.
Disebarkan
Secure Access Control Terminal
ATSAML11D15A-YU is appropriate for access-control terminals that require hardware-backed key protection and isolated trusted execution. Its Arm Cortex-M23 architecture provides the foundation for Arm TrustZone Technology, while the manufacturer highlights secure key storage, cryptographic support, and chip-level tamper resistance. These functions can protect credentials, authorization logic, and update pathways without assigning every security operation to general-purpose software. The 32 MHz processing rate is sufficient for keypad or credential handling and local communication, and the 24-SSOP package supports compact reader and controller designs. Firmware should isolate trusted boot and credential operations before deploying field-facing application code.
Disebarkan
Industrial Condition Monitor
The ATSAML11D15A-YU can serve as the supervisory controller in an industrial condition-monitoring system because its -40C to +85C temperature range supports demanding indoor equipment environments. The 32-bit Cortex-M23 core can combine sensor sampling, local filtering, threshold evaluation, event logging, and communications while retaining a modest 32 KB flash footprint. Hardware tamper detection is valuable in unattended monitoring equipment, and low sleep consumption permits long intervals between samples. The finished system still requires separate protection against transients, electrostatic discharge, and conducted disturbances; component temperature rating alone does not establish compliance for the complete industrial installation.
Disebarkan
Compact Data Acquisition Controller
ATSAML11D15A-YU fits compact data-acquisition equipment where a 32 MHz Cortex-M23 core must coordinate analog measurement and digital control in a small footprint. Its 32 KB flash and 8 KB SRAM provide sufficient space for calibration tables, control routines, sampling schedules, and communication firmware without requiring an external microcontroller. The mixed-signal SAM L11 architecture is useful when the design needs local conversion and low-power behavior rather than only digital logic. Designers should verify the required ADC channels, resolution, trigger behavior, reference accuracy, and peripheral multiplexing in the manufacturer data sheet, then place input and reference routing away from switching and high-current traces.
Disebarkan
Connected Equipment Controller
ATSAML11D15A-YU can act as the low-level controller in connected industrial or commercial equipment where secure communication, autonomous control, and low standby consumption must coexist. The Cortex-M23 processor can manage local state machines, interface drivers, and protocol tasks, while TrustZone provides a mechanism to separate security-sensitive services from application code. Secure key storage and tamper resistance are especially valuable in devices that maintain long-lived credentials. Actual connected-product suitability depends on the selected radio, protocol stack, response-time requirements, and memory headroom. If application code approaches the 32 KB flash limit, ATSAML11D16A-YU may provide a more practical upgrade path after software and pin compatibility are validated.
Disebarkan
Portable Diagnostic Device
The ATSAML11D15A-YU is well matched to portable diagnostic instruments that need responsive local control, protected operating data, and low standby demand. At 32 MHz, the Cortex-M23 core can perform measurement sequencing, signal processing, UI updates, and device management while the less-than-100 nA sleep specification supports energy-conscious standby behavior. TrustZone, secure key storage, and tamper resistance can protect configuration data and proprietary test sequences. The 24-SSOP format also assists compact enclosure designs, although it is larger than a typical QFN footprint. Prototype layouts should follow the exact package drawing and preserve access to programming, debug, reset, and clock signals.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk ATSAML11D15A-YU — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | ATSAML11D15A-YF | ATSAML11D15A-YFT | ATSAML11D15A-YUT | ATSAML11D16A-YU | ATSAML11D14A-YU |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 24-SSOP | 24-SSOP - same package | 24-SSOP - same package | 24-SSOP - same package | 24-SSOP - same package | 24-SSOP - same package |
| Processor Core | Arm Cortex-M23 | Arm Cortex-M23 | Arm Cortex-M23 | Arm Cortex-M23 | Arm Cortex-M23 | Arm Cortex-M23 |
| Maximum CPU Frequency | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Security Features | TrustZone, secure key storage, crypto hardware, chip-level tamper resistance | ATSAML11D15A family security features | ATSAML11D15A family security features | ATSAML11D15A family security features | SAM L11 family security features | SAM L11 family security features |
Penyeberangsung Jelas
- Combines low-power Cortex-M23 control with hardware-backed security (vsATSAML11D14A-YU)
- Maintains a practical balance of memory and firmware space (vsATSAML11D16A-YU)
- Uses the 24-SSOP package for compatibility with the ATSAML11D15A family (vsATSAML11D15A-MUT)
- Supports security-focused embedded designs at a low clock rate (vsATSAMV71Q19B-CB)
Catatan Desain
Place the device power and decoupling connections directly according to the Microchip package drawing and recommended-layout guidance. Keep the decoupling loop short and connect ground pins to the appropriate plane without introducing long return paths beneath the microcontroller. Because the 24-SSOP leads are relatively fine and widely spaced, inspect the PCB for assembly bridges, especially around adjacent signal pins. Preserve clean access to programming and debug signals so production programming and diagnostics do not require improvised board modifications.
Budget the complete power path rather than the CPU current alone. The manufacturer specifies less than 25 uA/MHz in active mode and less than 100 nA in sleep mode, but peripheral activity, analog conversion, communications, and wake transitions can dominate a duty-cycled design. Select a regulator with adequate transient response and acceptable quiescent current, then calculate average consumption from actual awake time, sleep time, and peripheral state. Include brownout behavior in firmware so an interrupted measurement is not mistaken for a valid result.
Route sensitive analog inputs away from switching nodes, high-current return paths, and digital clock lines. If the device performs measurement internally, preserve a quiet reference and supply region and follow the manufacturer recommendation for analog grounding. A 32 MHz digital clock can couple into adjacent low-level inputs even when the processor itself is operating correctly. For communications or external memory interfaces, maintain the specified impedance, avoid discontinuities, and place termination or protection components where their influence on signal timing is predictable.
Do not interchange ATSAML11D15A ordering suffixes without checking temperature grade, packing method, and marking. ATSAML11D15A-YU is the tube-packaged 24-SSOP configuration, while YFT and YUT identify other catalog delivery variants. Also treat ATSAML11D16A-YU and ATSAML11D14A-YU as different memory tiers rather than transparent substitutions. Before production release, load the correct device definition into the development tool, verify boot and peripheral initialization, and conduct a boundary test with the intended temperature and supply range.
Maklumat Kesediaan
The component is identified as RoHS3 compliant. No automotive qualification, REACH declaration, halogen-free declaration, or conflict-minerals statement is established by the cited product information.